To Protect Your Warranty, Use Only ENERPAC Hydraulic Oil.

Repair Parts Sheet POWERFUL SOLUTIONS. GLOBAL FORCE. Pow r Riser Lifting Jacks PR Series - 100 Ton Air Models L547 Rev. D 0/16 For Date Codes Beginning with the Letter A To Protect Your Warranty, Use Only ENERPAC Hydraulic Oil. Enerpac recommends that all kit components be installed to insure optimum performance of the repaired product. Note: This illustration is for reference only. The appearance of your unit may differ from the unit shown. P.R. Basic Assembly See Figure Cylinder Assembly See Figure 15 Filter/Lube Assemblies See Figures and Valve Sub-assemblies See Figures 16 through 0 Handle Assembly See Figure 5 Pump Sub-assemblies and Sub-components See Figures 4 through 1 Jack Components See Figures 1 and Manifold Assembly See Figure 1 Pendant Assembly (Not Shown - PRASA Models Only) See Figure 4

A RAISE LOWER THIS JACK IS FOR LIFTING ONLY! SUPPORT THE LOAD IMMEDIATELY AFTER LIFT BY OTHER APPROPRIATE MEANS. NEVER GET ON OR UNDER A LOAD SUPPORTED ONLY BY THE JACK. NEVER EXCEED THE RATED CAPACITY OF THE JACK. USE JACK ONLY ON SOLID SURFACES CAPABLE OF SUPPORTING THE LOAD AND THE BASE OF THE JACK. ALWAYS CENTER THE LOAD ON THE LIFTING SADDLE OF THE JACK. USE ONLY ENERPAC HYDRAULIC OIL, OR APPROVED EQUIVALENT. FAILURE TO HEED THESE WARNINGS MAY CAUSE LOSS OF LOAD OR FAILURE OF THE JACK RESULTING IN PROPERTY DAMAGE OR PERSONAL INJURY. CONSULT ENERPAC OPERATING INSTRUCTIONS AND ASME/ANSI B0.1 SAFETY STANDARD FOR ADDITIONAL INSTRUCTIONS ABOUT SAFE OPERATION. DO NOT REMOVE OR COVER THIS LABEL MOISTURE IN AIR LINE CAN CAUSE DANGEROUS ICING IN MUFFLER AND BLOW OUT FELT MUFFLER PADDING. USE ONLY ANTI-FREEZE LUBRICANT IN OILER AND MUFFLER. 88111E 899E Figure 1 - Main Assembly, PRAMA Models NOTE: This illustration is for reference only. The appearance of your unit may differ from unit shown. 5 14 6 1 15 1 Testing Procedure: Load the jack to 100 Tons, hold and check. No drift allowed. Lift 4-" @ 1 minute. Lower and check load holding.1" drift max. before load lock off. 100 TON CAPACITY 19 CAUTION 5 VIEW A-A 75 IN-LBS 11 9 8 18 5 6 0 75 IN-LBS 150 IN-LBS A A 100 TONS 100 NS 9 4 16 6 7 7 APPLY LOCTITE 4 150 IN-LBS 8 1 1 10 6 1 7 4 50 IN-LBS

Item Repair Parts List (Refer to figure 1) Model Qty. Description PRAMA10016L PRAMA1007L 1 (See Fig. ) (See Fig. ) 1 PR Basic Asm (See Fig. 4A & 4B) (See Fig. 4A & 4B) 1 Subassy, Pump and Air Motor. 40085E 40085E 1 Male Elbow /8-/8" 5 408E 408E 1 Load Cap PR Long Stm 6 41944E 41944E Tire/Rim Assembly 7 41779E 41779E 1 Air Tubing 8 8874E 8874E 1 Plug Hex O-Ring 9 (See Fig. 5) (See Fig. 5) 1 Handle Assembly 10 85469E 85469E 1 Gasket 11 (See Fig. ) (See Fig. ) 1 Filter Lube/Regulator Asm 1 401E - - - Square Hole Plug PR 1 8644E 8644E 1 Street Elbow 14 451E 451E 1 Label 100 Ton Capacity 15 458E - - - 1 Lifting Bar 4" PR 16 449E 4441E 1 Model Label 18 465E - - - Nut Plt - Lift Bar 19 899E 899E 1 Decal, Warning PWR R 0 B005046E B005046E 1 Screw 1/4-0 x /4" St 1 4605E 4605E 1"-8 Hex Lock Nut 6964E 6964E 1 Breather Vent 4 41979E 441E 1 Tube 5 46E - - - 4 HCS 5/16-18 x 1.5" Plt. 6 994E - - - 4 Lock Washer 5/16" 7 4198E 4198E 1 Screw Shoulder 8 89967E 89967E 1 Enerpac Logo - Large 9 B007046E B007046E Washer Hd. Screw 1/-0 x /4" 8607E 8607E 1 Control Valve Plate 41598E 41598E 1 Lower Weldment 4" PR 4 8469E 8469E SHC /8-16 x 1.75" 5 88111E 88111E 1 Label, Caution, Filter/Lube 6 4659E 4659E Decal Overlay 7 41945E 41945E Spacer N/A = Not Available.

THIS JACK IS FOR LIFTING ONLY! SUPPORT THE LOAD IMMEDIATELY AFTER LIFT BY OTHER APPROPRIATE MEANS. NEVER GET ON OR UNDER A LOAD SUPPORTED ONLY BY THE JACK. NEVER EXCEED THE RATED CAPACITY OF THE JACK. USE JACK ONLY ON SOLID SURFACES CAPABLE OF SUPPORTING THE LOAD AND THE BASE OF THE JACK. ALWAYS CENTER THE LOAD ON THE LIFTING SADDLE OF THE JACK. USE ONLY ENERPAC HYDRAULIC OIL, OR APPROVED EQUIVALENT. FAILURE TO HEED THESE WARNINGS MAY CAUSE LOSS OF LOAD OR FAILURE OF THE JACK RESULTING IN PROPERTY DAMAGE OR PERSONAL INJURY. CONSULT ENERPAC OPERATING INSTRUCTIONS AND ASME/ANSI B0.1 SAFETY STANDARD FOR ADDITIONAL INSTRUCTIONS ABOUT SAFE OPERATION. DO NOT REMOVE OR COVER THIS LABEL MOISTURE IN AIR LINE CAN CAUSE DANGEROUS ICING IN MUFFLER AND BLOW OUT FELT MUFFLER PADDING. USE ONLY ANTI-FREEZE LUBRICANT IN OILER AND MUFFLER. 88111E 899E Figure - Main Assembly, Pendant Controlled PRASA Models NOTE: This illustration is for reference only. The appearance of your unit may differ from unit shown. 5 16 51 1 1 Testing Procedure: Load the jack to 100 Tons, hold and check. No drift allowed. Lift 4-" @ 1 minute. Lower and check load holding.1" drift max. before load lock off. 100 TON CAPACITY CAUTION 19 50 VIEW B-B 11 4 8 A 4 5 45 150 IN-LBS B B 4 100 TONS 100 TONS A 9 P 5 6 44 0 75 IN-LBS 9 1 9 0 INSTALL IN LOWER PORT OF VALVE 15 4 18 7 14 51 7 47 46 41 8 6 APPLY LOCTITE 4 150 IN-LBS 1 48 7 75 IN-LBS 1 10 6 1 5 49 50 IN-LBS 4

Repair Parts List (Refer to figure ) Item Model PRASA10016L PRASA1007L Qty. Description 1 (See Fig. ) (See Fig. ) 1 PR Basic Asm (See Fig. 5A & 5B) (See Fig. 5A & 5B) 1 Subasy, Pump and Air Motor 40085E 40085E 1 Male Elbow /8-/8" 5 408E 408E 1 Load Cap PR Long Stm 6 41944E 41944E Tire/Rim Assembly 7 41779E 41779E 1 Air Tubing 8 8874E 8874E 1 Plug Hex O-Ring 9 (See Fig. 5) (See Fig. 5) 1 Handle Assembly 10 85469E 85469E 1 Gasket 11 (See Fig. ) (See Fig. ) 1 Filter Lube/Regulator Asm 1 401E - - - Square Hole Plug PR 1 864E 864E 1 Male Elbow 14 444E 4444E 1 Decal, Blank 15 (See Fig. 4) (See Fig. 4) 1 Pendant, Air 16 451E 451E 1 Label 100 Ton Capacity 18 41965E 41965E 1 Hose 19 899E 899E 1 Decal, Warning PWR R 0 B005046E B005046E 1 Screw 1/4-0 x /4" St 1 4605E 4605E 1"-8 Hex Lock Nut 6964E 6964E 1 Breather Vent 4 - - - 4504E 1 Hanger, 10" Lock Ring 5 - - - 455E 4 SHCS, #10- x 1/" SS 6 - - - 9940E 4 Lockwasher, #10 7 B007046E B007046E Washer Hd. Screw 1/4-0 x /4" 8 4968E 4968E Swivel Tee, 1/8" 9 DS104660 DS104660 1 Control Valve, Air 0 45970E 45970E 1 Nipple, Male 1/4" x 1/8" 1 41979E 441E 1 Tube 458E - - - 1 Lifting Bar 4" PR 465E - - - Nut Plt - Lift Bar 4 46E - - - 4 HHCS 5/16-18 x 1.5" Plt. 5 994E - - - 4 Lock Washer 5/16" 6 4198E 4198E 1 Screw Shoulder 7 89967E 89967E 1 Enerpac Logo - Large 9 467E 467E 1 S-Hook, Pendant 41 4445E 4445E 1 Shuttle Valve 4 4099E 4099E 1 Hose, /16" 10.5" Lg 4 4098E 4098E 1 Hose, /16" 1.5" Lg 44 4667E 4667E Reducer, 1/4-1/8" 45 4966E 4966E 1 Street Elbow, 1/8" 46 18970E 18970E Swivel, Straight, 1/" 47 4967E 4967E 1 Street Elbow, 1/4", 90 Deg. 48 41598E 41598E 1 Lower Weldment 4" PR 49 8469E 8469E SHC /8-16 x 1.75" 50 88111E 88111E 1 Label, Caution, Filter/Lube 51 4659E 4659E Decal Overlay 5 41945E 41945E Spacer N/A = Not Available. 5

Figure - 4199SR, 4408SR Pow r Riser Basic Assembly 4 0-5 FT. LBS. 1 0 1 9 4 8 7 7 15 17 14 8 10 19 TORQUE BOLTS TO 5 FT-LBS. MINIMUM TORQUE ADAPTER TO 180 FT-LBS. MINIMUM 6 TORQUE ACORN NUT TO 90-100 FT-LBS. 5 16 1 18 5 6

Repair Parts List (Refer to figure ) Model Item PRAMA10016L and PRASA10016L PRAMA1007L and PRASA1007L Qty. Description BASIC ASSY 4199SR 4408SR 1 41886E 41886E 1 Housing Mach P. R. 4 (See Fig. 15) (See Fig. 15) 1 100 Ton Cylinder Assy. 5 85477E 85477E Jam Nut 6 (See Fig. 14) (See Fig. 14) 1 O.C. Valve and Hoses 7 9947E 9947E 6 Lock Washer 5/8" 8 9605E 9605E 6 SHCS 5/8-11 x 1.5" Lg. 9 41941E 41941E 1 100 Ton P.R. Base 10 89754E 89754E 1 Screen - " Nipple 1 44968E 44968E Rubber Ball /8" 70 14 9950E 9950E 1 1/4" Soc Pipe Plug 15 1 Gasket Adapter 16 41948E 41948E Axle Shaft 17 4194E 4194E 1 Adapter O.C. Valve 18 475E 475E PR Base Pin 19 46740E 46740E 1 Acorn Nut 5/8-11 0 41940E 41940E 1 Ring 100 Ton 1 1 O-Ring 6-/4 x 7-1/4" 1 O-Ring 9" x 9-1/" 1 Gasket Base 4 1 O-Ring Power Riser 5 6601E 6601E 1 Magnet 7 1 O-Ring 6" x 6-1/4" 8 6818E 6818E Gasket Plug Included in 54411K Repair Kit. 7

Figure 4A - 69746SR Pump and Motor Sub-Assembly (PRAMA Models Only) 1 1 17 A 6 11 10 9 0 5 19 10 4 7 14 1 15 PUMP ASSEMBLY SPECIFICATIONS: 16 TONNAGE: 100 TONS PRESSURE RELIEF: 9,500-9,700 PSI PRESSURE UNLOADING: 800 PSI 8

Repair Parts List (Refer to figures 4A and 4B) Item Part Number Qty. Description 1 69445SR 1 Pump Asm 4P Air 6601E 1 Gasket-Motor 681E 1 Gasket-Pump @ Motor 4 68551E 1 Gasket-Pump @ Valve 5 DD608101E 1 Cover Plate, Reservoir 6 85501E 1 Air Motor 7 6906E 1 Pin Dowel /16-1 9 (See Fig. 1) 1 Manifold Asm NPR 10 86184E 5 SHCS /8-16 x 1-1/" 11 (See Fig. 0) 1 Locking Valve w/relief 1 (See Fig. 16) 1 Control Valve Asm. 1 48E 4 SHCS /8-16 x 8.0" 14 6896SR 1 Adapter Assy. 15 6944E 1 Nipple, 1/4NPT x 1.5L 16 8041E 1 Pipe Coupling, 1/4" 17 (See Fig. 1) 1 Filter Block Assembly 18 561604E 1 Roll Pin 1/8 x /8" Lg. 19 41964E Swivel Fitting 0 DD610607E 1 Valve Gasket 1 B10108X SHCS, 1/4-0 x 1.5" Lg Included in 54177K Repair Kit. Figure 4B - 69746SR Pump and Motor Sub-Assembly (PRAMA Models Only) 1 18 9

Figure 5A - 41976SR Pump and Motor Sub-Assembly (PRASA Models Only) PUMP ASSEMBLY SPECIFICATIONS: TONNAGE: 100 TONS PRESSURE RELIEF: 9,500-9,700 PSI PRESSURE UNLOADING: 800 PSI 10

Repair Parts List (Refer to figures 5A and 5B) Item Part Number Qty. Description 1 69445SR 1 Pump Asm 4P. 6601E 1 Gasket-Motor 681E 1 Gasket-Pump @ Motor 4 68551E 1 Gasket-Pump @ Valve 5 DD608101E 1 Cover Plate, Reservoir 6 85501E 1 Air Motor 7 6906E 1 Pin Dowel /16-1 9 (See Fig 1) 1 Manifold Asm NPR 10 86184E 5 SHCS /8-16 x 1-1/" 11 (See Fig 0) 1 Locking Valve w/relief 1 (See Fig 17) 1 Control Valve Asm. 1 477E 4 SHCS /8-16 x 8.0" 14 6896SR 1 Adapter Assy. 15 6944E 1 Nipple, 1/4" NPT x 1.5"L 16 8041E 1 Pipe Coupling, 1/4 17 (See Fig 1) 1 Filter Block Asm 18 561604E 1 Roll Pin 1/8 x /8" LG 19 41964E Swivel Fitting 0 DD610607E 1 Valve Gasket 1 B10108X SHCS, 1/4-0 x 1.5" Lg Included in 54177K Repair Kit. Figure 5B - 41976SR Pump and Motor Sub-Assembly (PRASA Models Only) 11

Figure 6A - 69445SR Pump Assembly 180 IN-LBS. 46 1 5 6 7 8 50 IN-LBS. 50 IN-LBS. 180 IN-LBS. 15 16 46 5 IN-LBS. 4 18 14 11 00 IN-LBS. 1 1 5 10 9 4 1 8 8 7 10 IN-LBS. 5 6 1 180 IN-LBS. 46 5 1 4 10 IN-LBS. 5 7 8 175 IN-LBS. 41 4 17 18 44 45 19 5 IN-LBS. 9 18 44 40 150 IN-LBS. 49 50 150 IN-LBS. 5 IN-LBS. 47 48 0 1

Repair Parts List (Refer to figures 6A and 6B) Item Part Number Qty. Description Item Part Number Qty. Description 1 44917E 1 Pump Body 4 Piston 7 68849E 1 Plate-Bottom 6860E 1 Bearing, Roller 8 68855E 1 Gearset, /8 Clydesdale 660E 1 Thrust Bearing 9 68850E 1 Shaft-Idler 4 66474E Thrust Washer 0 68884E 1 Screen 5 (See Fig. 9) 1 Eccentric Shaft Assembly 1 689E Tube-Guide. 6 66106E 1 Thrust Bearing 89148E 1 SHCS 1/4-8 x 1-1/" 7 66108E Thrust Washer 5 685E 1 Spring 8 (See Fig. 7) 1 Adapter-Shaft Asm. 6 81E 1 Roll Pin 1/8 x 15/16" 9 5600E O-Ring 1-7/8 x " Ure 7 686E 1 Screw, Ball Stop 10 68978E 1 Retaining Ring 8 8576E Gasket 5/64 x 19/" 11 68915E 1 Adaptor.10 Piston 40 6855E 4 SHCS 1/4-8 x 1-/4" 1 6880E 1 Piston.10 Dia. 41 68569E 1 Tube Return 1 6840E 1 Spring, Piston 4 6951E Shaft Adp Backup Was. 14 68810E 1 Ball Stop 4 6604E 1 Spring 15 9950E 1 1/4" Soc Pipe Plug 44 68891E Bearing 16 (See Fig. 8) 1 Unloading Piston Assy 45 6889E 1 Ring-Retaining 17 6604E 1 Ball Retainer 46 A100745 Pipe Plug 1/8" Flush 18 90906E 5 Ball 1/8" 47 68004E 1 Seat - Ext Relief 19 66046E 1 Intake Seat 48 6800E 1 Cone - Ext Relief 0 68851SR 1 Tube Asm 49 66085E 1 Spring - Relief Valve 1 91701E Ball 5/16" 50 6608E 1 Relief Valve Adj. Screw 4671E 1 Unloading Spring 5 467E 1 Spring Cap Unload Valve 4674E 1 Set Screw Unloading Valve 5 (See Fig. 10) Piston Blk.10 4 4675E 1 Hex Nut Unloading Valve 54 B15608 6 SHCS 5 97641E 1/16" Soc Pipe Plug 55 8687E 6 SHCS 5/16-4 x 5/8" Included in 54177K Repair Kit. Included in 55057K Relief Kit. 10 9 4 1 Figure 6B - 69445SR Pump Assembly 8 7 6 55 175 IN-LBS. 4 5 1 7 8 175 IN-LBS. 54 0 40 150 IN-LBS. 1

Figure 7-6889SR Adapt-Shaft Assembly Repair Parts List (Refer to figure 7) Item Part Number Qty. Description 1 6891E 1 Adapter Shaft 6600E 1 Bearing 68901E 1 Seal Included in Repair Kit 54177K. Figure 8-4766SR Unloading Piston Assembly Repair Parts List (Refer to figure 8) Item Part Number Qty. Description 1 4765E 1 Unload Piston 560009E 1 O-Ring 4768E 1 Back-Up Washer 4 4686E 1 Roll Pin Figure 9-68906SR Eccentric Shaft Assembly 5 1 4 Repair Parts List (Refer to figure 9) Item Part Number Qty. Description 1 68907E 1 Eccentric Shaft, 7/8" 68818SR 1 Eccentric Asm. 69475E Bearing Washer 4 6786E 1 Retaining Ring 5 90548E 1 Ball Figure 10-688SR Piston Block Assembly 1 1 11 10 14 400 IN-LBS. 9 1 15 150 IN-LBS. 4 5 5 IN-LBS. 6 8 7 150 IN-LBS. 00 IN-LBS. Repair Parts List (Refer to figure 10) Item Part Number Qty. Description 90906E Ball 1/8" 6604E 1 Spring 4 68810E 1 Ball Stop 5 6604E 1 Ball Retainer 6 66046E 1 Intake Seat 7 8669E 1 Gasket 9/64 x 5/8" 8 6885E 1 Plug, Piston Block 9 8576E 1 Gasket 5/64 x 19/" 10 68915E 1 Adaptor.10 Piston 11 6840E 1 Spring, Piston 1 6880E 1 Piston,.10 Dia. 1 68970SR 1 Adapter Assy. 14 560008E 1 O-Ring /16 x 5/16" 15 A100745 1 Pipe Plug 1/8" Flush Included in Repair Kit 54177K. 14

Figure 11-6896SR Adapter Assembly Repair Parts List (Refer to figure 11) Item Part Number Qty. Description 1 8807E 1 Valve Adapter 65881E B-U Ring 56001E O-ring, /8 x 1/" Included in Repair Kit 54177K. Figure 1-68818SR Eccentric Bearing Assembly Repair Parts List (Refer to figure 1) Item Part Number Qty. Description 1 6891E 1 Ring, Eccentric 68060E 1 Bearing, Sleeve Figure 1-69740USR Filter Block Assembly Repair Parts List (Refer to figure 1) Item Part Number Qty. Description 1 69546E 1 Filter Block 69670E 1 Oil Filter Power Pump 69144E 1 Adapter Filter 4 9950E 1/4" Soc Pipe Plug 5 560011E 4 O-Ring 5/16 x 7/16" URE 6 560008E 1 O-Ring /16 x 5/16" 15

Figure 14-45SR OC Valve Subassembly Repair Parts List (Refer to figure 14) Item Part Number Qty. Description Item Part Number Qty. Description 1 695MSR 1 O.C. Valve Asm New PR 5 454E Hose 1/4 x 17" Nw PR 18970E 1 Elbow 1/4" 90 Deg Strt 6 84084E 1 /8" Pipe Plug - Flush 45E 1 Elbow 1/4-/8" 90 Strt N/S 94414E 1 Ball 7/16" 4 6818E Gasket-Plug N/S = Not Shown. Figure 15-41917SR, 440SR Cylinder Assembly Model Repair Parts List (Refer to figure 15) PRA_A10016L (all versions) PRA_A1007L (all versions) Item Asm. 41917SR Asm. 440SR Qty. Description 1 41918E 449E 1 Cylinder Weldment 4191SR 447SR 1 Piston Rod Asm. 4194E 4194E 1 100 Ton Head Gland 4 1 T-Seal Rod 4" Dia 5 1 T-Seal Piston 5-1/4" 6 1 Wiper 4" Rod Dia 7 1 O-Ring 5" x 5-1/4" 8 1 B-U Washer 9 4195E 4195E 1 Ring 10 N/A 408E 1 Swivel Eye Bolt 1/" 11 N/A 44888E 1 Washer Eyebolt 1 45664E 45664E 1 O-Ring Face Seal Plug 1 44865E 45666E 1 O-Ring Ftg, /8" NPT Included in 54401K Repair Kit. 16

Figure 16-69101SR 4-Way Manual Valve Subassembly (PRAMA Models Only) Repair Parts List (Refer to figure 16) Item Part Number Qty. Description Item Part Number Qty. Description 1 476E 1 Valve Rotor 1 6809E 1 Seal 560011E 4 O-Ring 1 6808E Spring Washer 68180E 1 Subplate - Valve 14 6805E 1 Detent Spring 4 5605E 1 O-Ring 15 9549E 1 Ball 5 6806E Thrust Washer 16 69091E 1 Valve Handle 6 68155E 1 Thrust Bearing 17 44595E 1 Screw 7 56001E 1 O-Ring 18 8517E Screw 8 6915E 1 Upper Valve Block 19 9598E 4 Screw 9 9804E 1 Drive Lok Pin 0 560008E 1 O-Ring 10 560011E O-Ring 1 68181E Seal 11 6588E Washer Y0010765E 1 Lockwasher Included in Valve Kit 54490K. 17

Figure 15 17-41949SR P4WM Air Valve Assembly (PRASA Models Only) Repair Parts List (Refer to figure 17) Item Part Number Qty. Description Item Part Number Qty. Description 1 (See Fig. 18) 1 Valve Assembly TC 5 68711E Spring (See Fig. 19) Air Cyl Assembly 6 560011E 4 O-Ring 5/16 x 7/16" 6888E 1 Cover, Valve 7 9850E 4 Screw 4 6889E 1 Gasket Cover 8 41959E 8 SHCS #10-4 x.5" Figure 16 18-68710SR Valve Assembly TC (PRASA Models Only) 16 17 75 IN*LBS. 1 84-108 IN-LBS. 18 4 1 15 50 IN-LBS. 14 11 10 1 Repair Parts List (Refer to figure 18) Item Part Number Qty. Description 1 68708E 1 Body-Valve 68709E 1 Slider 90548E 1 Ball 4 4054E 1 Screw 6 560009E O-Ring 7 6891E Back-up Washer 8 688E Seal 9 6884E Spring 10 56008E 1 O-Ring 11 6885E 4 Bearing, Roller 1 6890E Pin Bearing 1 94418E 1 Set Screw, 5/16-18 x 1/4" 14 6864E Screw 15 6881E 1 Plate-Top 16 9549E 1 Ball, 1/4" 17 560008E 1 O-Ring 18 6966E Roll Pin 5 IN-LBS. 9 8 6 7 18

Figure 19-41954SR Air Cylinder Assembly (PRASA Models Only) 8 9 10 5 1 11 1 7 4 14 15 1 Repair Parts List (Refer to figure 19) Item Part Number Qty. Description 1 4744E 1 Body Air Cylinder 560006E 1 O-Ring 1/8-1/4" 560010E 1 O-Ring 1/4-/8" 4 4747E 1 Air Cylinder Piston 5 4749E 1 Spring, Air Cylinder 7 41956E 1 End Cap 8 5600E 1 O-Ring 1-1/16 x 1-/16" 9 68497E 1 Seal 10 560017E 1 O-Rng 11/16 x 1/16 11 560910E 1 O-Ring SAE Port #10 1 4746E 1 Push Pin Air Valve 1 41958E 1 Override Pin 14 4750E 1 E-Ring 1/4" Shaft 15 4748E 1 Spring Plate Air Valve 19

Figure 0-4480SR Locking Valve Subassembly (with relief) SPOOL AND SEAL REPLACEMENT INFORMATION OLD DESIGN - ITEM A 0.4" 0.8" 0.198" 0.196" DIA. IMPORTANT: Use items B and 4B with NEW design spool, item B. A B A A A B B B 0.9" 0.505" NEW DESIGN - ITEM B 0.10" 0.05" 0.64" 0.6" DIA. IMPORTANT: Use items A and 4A with OLD design spool, item A. 0.07" 0.50" Note: Old design spool (A) must be replaced with new design spool (B) if it is worn or damaged. Old design spool (A) is no longer available. Repair Parts List (Refer to figure 0) Item Part Number Qty. Description Item Part Number Qty. Description 1 407E 1 Locking Valve Body - Relief 1 6858E 1 Plug SAE #4 A (not available) 1 Spool Piston (old design) 1 84084E 1 Spring Washer B 477E 1 Spool Piston (new design) 14 69870E 1 Spring Eyelet Lock A 5608106E Backup Washer 8-106 15 68004E 1 Seat - Ext Relief B 497E Backup Washer TEF -010 16 6800E 1 Cone - Ext Relief 4A 560106E 1 O-Ring /16 x /8" 17 66085E 1 Spring - Relief Valve 4B B100550 1 O-Ring 1/4 x /8" 18 6608E 1 Relief Valve Adjusting Scr. 5 68590E 1 Seat 19 40049E 1/16" Pipe Plug - Flush 6 956E 1 Ball 9/" 0 69518E 1 Screen O.C. Valve 7 69508E 1 Plug - Adapt P.R. Lock 1 44E 1 Screen O.C. Valve 8 6818E 1 Gasket - Plug 69517E 1 Screen Cap 9 560010E O-Ring 1/4 x /8" Ureth 85E 1 Pipe Plug 1/4" Flush 10 560016E 1 O-Ring 5/8 x /4" Ureth 4 476E 1 Washer PR Lock Block 11 68870E 1 Compression Spring 5 68871E 1 Compression Spring Included in 55057K Relief Kit. Included with item B 0

Figure 1-69749SR Manifold Assembly 50 IN-LBS 4 1 50 IN-LBS 9 150 IN-LBS 90 IN-LBS 7 8 50 IN-LBS Repair Parts List (Refer to figure 16) Item Part Number Qty. Description Item Part Number Qty. Description 1 6949E 1 Manifold Pow r Riser 7 45664E 1 O-Ring Face Seal Plug 40049E 1/16" Pipe Plug - Flush 8 4566E 1 O-Ring Face Tube Ftg 1/4" 8109E 1 Pipe Plug 1/8" Flush 9 4100067E 1 Nipple 1/4" 4 4166E 1 Elbow 90 /8-1/4" 1

Figure - DS107900SR Filter Lube Assembly (PRAMA Models Only) 5 1 7 6 VIEW A - A SIGHT GLASS TO FACE THIS DIRECTION 4 NOTE ( ): ASSEMBLE WITH LOCTITE 4 Item Repair Parts List (Refer to figure ) Part Number Models PRASA10016L and PRASA1007L Qty. Description 1 DS1018118E 1 Air Filter 864E 1 Air Lubricator 69998E 1 Pipe Nipple 4 4511E 1 Bracket/Nipple Weldment 5 4176E 1 Swivel Male 1/" NPTF 6 85851E 1 Air Valve 7 8644E 1 Street Elbow

Figure - DS1019900SR Filter Lube Assembly (PRASA Models Only) 9 7 8 1 10 5 6 VIEW A - A NOTE ( ): ASSEMBLE WITH LOCTITE 4 SIGHT GLASS TO FACE THIS DIRECTION 4 Item Repair Parts List (Refer to figure ) Part Number Models PRASA10016L and PRASA1007L Qty. Description 1 DS1018118 1 Filter/Regulator 864E 1 Air Lubricator 69998 1 Pipe Nipple 1/" BRS 4 4511E 1 Bracket/Nipple Weldment 5 4176E 1 Swivel Male 1/" NPTF 6 85851E 1 Air Valve 7 478E 1 Male Run Tee 1/" 8 477E 1 Pipe Adpter, 1/-1/8" 9 480E 1 Swivel Adapter, 1/8"-90 10 8644E 1 Street Elbow

Figure 4-41950SR Motor Pendant (PRASA Models Only) Repair Parts List (Refer to figure 4) Item Part Number Qty. Description 1 41968E 1 Pendant Body 41969E 1 Block Air Pendent 4196E Cartridge-Air 4 481E Swivel ADP 1/8" 5 606961E Ball 5/" 6 68808E Retaining Ring 7 41970E Cartridge Cap 4

Figure 5-41961SR Upper Handle Assembly Repair Parts List (Refer to figure 5) Item Part Number Qty. Description Item Part Number Qty. Description 1 41595E 1 Upper Weldment 8 41614E 1 Washer 9/16" ID x /" 468E 1 Handle Lock Lever 9 4497E 1 Roll Pin 5/ x 7/8" 4 41600E 1 Sleeve 11 8849E 4 Washer SS 1/4" 5 41601E 1 Handle Rod 1 440E 4 Pin Ring 6 4160E 1 Spring. 656 x 9.50" 1 48E Pin Handle Lever 7 4161E 1 E-Ring.8/.8 x.04 5

Enerpac Worldwide Locations e-mail: info@enerpac.com internet: www.enerpac.com Australia and New Zealand Actuant Australia Ltd. P.O. Box 6867 Wetherhill Park, NSW1851 Block V Unit Regents Park Estate 91 Park Road Regents Park NSW 14 Australia T +61 87 177 00 F +61 97 48 648 sales-au@enerpac.com Brazil Power Packer do Brasil Ltda. Rua Luiz Lawrie Reid, 548 0990-760 - Diadema (SP) - Brazil T +55 11 5687 11 Toll Free: 0800 891 5770 vendasbrasil@enerpac.com China (Taicang) Actuant (China) Industries Co. Ltd. No. 6 Nanjing East Road, Taicang Economic Dep Zone Jiangsu, China T +86 051 58 7500 F +86 051 55 9690 Toll Free: +86 400 885 069 sales-cn@enerpac.com France, Switzerland, North Africa and French speaking African countries ENERPAC Une division d ACTUANT France S.A.S. ZA de Courtaboeuf, avenue de la Baltique 91140 VILLEBON /YVETTE France T + 1 60 1 68 68 F + 1 69 0 7 50 sales-fr@enerpac.com Germany and Austria ENERPAC GmbH P.O. Box 0011 D-40401 Düsseldorf Willstätterstrasse 1 D-40549 Düsseldorf, Germany T +49 11 471 490 F +49 11 471 49 8 sales-de@enerpac.com India ENERPAC Hydraulics (India) Pvt. Ltd. No. 10, Bellary Road, Sadashivanagar, Bangalore, Karnataka 560 080 India T +91 80 98 9000 info@enerpac.co.in www.enerpac.com Italy ENERPAC S.p.A. Via Canova 4 0094 Corsico (Milano) T +9 0 4861 111 F +9 0 4860 188 sales-it@enerpac.com Japan Applied Power Japan LTD KK Besshocho 85-7 Kita-ku, Saitama-shi 1-081, Japan T +81 48 66 4911 F +81 48 66 4955 sales-jp@enerpac.com Middle East, Egypt and Libya ENERPAC Middle East FZE Office 4, LOB 15 P.O. Box 18004, Jebel Ali, Dubai United Arab Emirates T +971 (0)4 887686 F +971 (0)4 887687 sales-ua@enerpac.com Russia Rep. office Enerpac Russian Federation Admirala Makarova Street 8 151 Moscow, Russia T +7 495 98090 91 F +7 495 98090 9 sales-ru@enerpac.com Southeast Asia, Hong Kong and Taiwan Actuant Asia Pte Ltd. 8 Joo Koon Circle Singapore 69109 T +65 68 6 0611 F +65 64 84 5669 Toll Free: +1800 6 77 sales-sg@enerpac.com South Korea Actuant Korea Ltd. Ba 717, Shihwa Industrial Complex Jungwang-Dong, Shihung-Shi, Kyunggi-Do Republic of Korea 49-450 T +8 1 44 4506 F +8 1 44 4507 sales-kr@enerpac.com Spain and Portugal ENERPAC SPAIN, S.L. Avda. Los Frailes, 40 Nave C & D Pol. Ind. Los Frailes 8814 Daganzo de Arriba (Madrid) Spain T +4 91 884 86 06 F +4 91 884 86 11 sales-es@enerpac.com Sweden, Denmark, Norway, Finland and Iceland Enerpac Scandinavia AB Kopparlundsvägen 14, 71 0 Västerås Sweden T +46 (0) 771 41 50 00 scandinavianinquiries@enerpac.com The Netherlands, Belgium, Luxembourg, Central and Eastern Europe, Baltic States, Greece, Turkey and CIS countries ENERPAC B.V. Galvanistraat 115, 6716 AE Ede P.O. Box 8097, 6710 AB Ede The Netherlands T +1 18 55 911 F +1 18 55 848 sales-nl@enerpac.com Enerpac Integrated Solutions B.V. Spinelstraat 15, 7554 TS Hengelo P.O. Box 41, 7550 AK Hengelo The Netherlands T +1 74 4 0 45 F +1 74 4 0 8 integratedsolutions@enerpac.com South Africa and other English speaking African countries Enerpac Africa Pty Ltd. No. 5 Bauhinia Avenue Cambridge Office Park Block E Highveld Techno Park Centurion 0157 Republic of South Africa T: +7 1 940 0656 sales-za@enerpac.com United Kingdom and Ireland ENERPAC UK Ltd. 5 Coopies Field Morpeth, Northumberland NE61 6JR, England T +44 1670 5010 00 sales-uk@enerpac.com USA, Latin America and Caribbean ENERPAC World Headquarters P.O. Box 41 Milwaukee WI 501-41 USA N86 W1500 Westbrook Crossing Menomonee Falls, Wisconsin 5051 T +1 6 9 1600 F +1 6 9 706 User inquiries: T +1 800 4 766 Distributor inquiries/orders: T +1 800 558 050 F +1 800 68 0490 Technical inquiries: techservices@enerpac.com sales-us@enerpac.com All Enerpac products are guaranteed against defects in workmanship and materials for as long as you own them. For the location of your nearest authorized Enerpac Service Center, visit us at www.enerpac.com 0016