Little David ase Former F-F Semi utomatic ase Former Ver. E //0 Operator s Manual
LITTLE DVID SE FORMER F-F Operation Manual opyright Loveshaw 0 Easton Turnpike, PO. ox South anaan, P Tel: -00-- 0-- Fax: 0--0 www.loveshaw.com PDLOKER, LTD. Unit runel Gate West Portway Industrial Estate ndover, Hampshire SP0 SL ENGLND Tel: - Fax: -
Table of ontents hapter : Introduction hapter : Operating Safety hapter : Overview and Specifications hapter : Installation hapter : Theory of Operation hapter : Maintenance hapter : Troubleshooting hapter : Warranty hapter : Machine omponents hapter 0: Schematics hapter : Machine vailable Special Options
HPTER : INTRODUTION Thank you for purchasing the Little David F-F by Loveshaw. This machine is designed to be a simple yet effective way to form corrugated boxes and hold the box while an operator fills it with product. Some of the key features of the F- F are: DJUSTMENT FREE There are no adjustments required for varying width or length boxes. No scales to read, cranks to turn or locks to fasten. (There are adjustable aids for new users to make running the machine easier.) ESE OF USE The operator simply opens the blank and lowers it onto the Tee-Rail and Folding lock to tuck both minor flaps. Then they push the case against the folding block and the major flaps are folded up automatically. FEW MOVING PRTS The machine is designed to be low-maintenance due to the low number of moving parts and the low stress levels on the components. VERSTILE The F-F will work with nearly any case sealer. SIMPLIITY Low number of parts and NO PL. It s important that anyone installing, using or maintaining the machine read this manual before starting the task. fter reading this manual, a person will be able to: Set-up the machine and optimize it for their production. Maintain the machine in good working order. Troubleshoot any problems. Order spare parts. Throughout this manual are illustrations to aid in the performance of the various tasks. HPTER : OPERTING SFETY Observe the warnings and cautions below when using the Little David F-F case former. If a safety label is missing or not legible it must be replaced immediately. Failure to follow safety labels can lead to injury or damage to the machine. Important Requirement to System Operation
n electrical receptacle must be located near the machine. The line cord connection to the receptacle is the disconnect means for the machine. The receptacle must be located in an area that is easily accessible to all personnel. Warning: Potential odily Injury lways disconnect all sources of energy to the machine before performing maintenance. Sources of energy include electrical and pneumatic. Refer to your company s lock out tag out procedures. Never bypass or remove safety guards from the machine. Never override safety devices such as Emergency Stop switches. Never make adjustments to the machine when the machine is operating. Never place hands or body inside confines of the machine unless all power sources are locked out. Never wear jewelry, loose clothing, such as ties, scarves etc. and long hair must be pulled back when operating this machine. Never pull a jammed box out of the machine while it is in operation. Stop machine and release pneumatic energy before clearing a jam. HPTER : OVERVIEW ND SPEIFITIONS
MHINE SPEIFITIONS Electrical: 0 V Single Phase, 0 Hz., >amp. Pnuematic: 0 psi, clean, dry air, >FM per minute. Dimensions: long x 0-/ wide x -/ high (w/o leveling pads). Weight: 0 lbs. ox Range: (L x W x H) x x (Min.) x x infinity (Max.) HPTER : INSTLLTION IMPORTNT: Use care when lifting and moving the machine. Do not drop or jar the machine or damage may result. Lift the machine off of the shipping skid with a powered fork lift by positioning forks under main frame beam. enter the forks under the frame so the unit does not tip. Unpack the shipping box that contains the leveling pads and hardware. While the machine is elevated and secure, install the threaded rod (/-UN X ) and leveling pads. Use a () jam nut on top of leveling pad and () on rod above machine leg.
Determine the desired height of the machine by measuring the surface to floor distance of your mating case sealer or conveyor. Set the leveling pads so that the Tee-Rail top surface is / -/ above the mating machine s working surface. Optional threaded rods up to long are available. ONNETION TO SE SELERS: Kits are available to connect the F-F to any of the Little David case sealers. These kits should be used to maintain alignment between the two machines. Installation instructions for connecting specific machines are supplied with each one. There is also a Universal onnection Kit available to connect the F-F to another company s case sealer or conveyor. The Little David connection kits can be ordered thru our aftermarket department using the following part number format:.kff- dd the model number of your machine. Example:.KFF-LD for connection to the Little David LD The available kits are:.kff-ld.kff-lds.kff-ldxss.kff-ldxrt.kff-ldxut.kff-ld.kff-ldr.kff-ldx/ss.kff-sext ELETRIL ND PNEUMTI ONNETIONS Electrical: The F-F is equipped with a 0 ft. line cord and a NEM - male -prong straight plug. The current requirement is less than ampere. Pneumatic: onnect the air supply to the manual shut off valve on the back panel of the machine. The shut off valve comes factory equipped with a Foster 0- (Series ) male quick-disconnect fitting. If the mating socket is not available remove the fitting and insert your own ¼ NPT fitting to connect to plant air. The regulator should be set to 0 psi.
HPTER : THEORY OF OPERTION The basic function of the F-F is to serve as a case former and pack station for a low to medium volume operation. With minimal physical inputs from a human operator, the machine will fold the bottom major flaps of an RS or HS corrugated box and hold the box in place while the operator fills it with product and dunnage. fter the case has been filled, the operator will manually push the case out of the machine into either a case sealer or onto conveyor. The F-F does not have the capacity to tape or glue the flaps. That must be accomplished by a secondary machine. The machine can be used as a semi-automatic case erector when coupled with a side-belt bottom only case sealer. The operating sequence is as follows:. ased on the length of the cases you are using, set the folding block forward to minimize the distance between the front of the case and the front of the machine. This will reduce the time required to push the box out of the machine. Lift up on the spring pin located at the back of the folding block and move the folding block accordingly. The spring pin will snap into the tee rail when aligned with the series of holes.(this function is not available on machine with pneumatic pusher option). To turn the machine on, pull up on the RED knob marked E-STOP. This will supply air to the pneumatic system. THIS DEVIE DOES NOT ONTROL ELETRI POWER.. The operator will pick up a blank and grip it at the top, on the minor flaps and open the case to form its shape.
. Position the case centered over the tee-rail with the long side of the box running in the direction of box travel.. Lower the case front end first onto the tee-rail to fold the front minor. While doing this lower the rear end onto the sloped surface of the folding block to fold in the rear minor.. In one motion, bring the case downward and forward until it sits evenly on the tee-rail.
. Slide case rearward until it contacts the nose of the folding block. The roller air switch housed in the nose will be activated and the major folding panels will rise up.. If the case does not fold properly press the yellow RESET button and repeat step.. t this point the case is ready to be filled. 0a. Manual Version - Once the case is ready the operator will push it out over the rollers into the mating machine. When the box clears the exit photo-eye, the flap folders will reset and the machine is ready for the next cycle.
0b. Pusher Version - Once the case is filled and ready the operator will push the green start button (fig. ). This will actuate the pusher and transfer case into the mating machine (fig. ). The exit photo-eye will reset the flaps down and return the pusher to the home position so the machine is ready for the next cycle (fig. ). Figure Figure Figure
HPTER : MINTENNE THE FOLLOWING MINTENNE HEKS SHOULD E PERFORMED FTER EVERY 0 HOURS OF OPERTION. MEHNIL. HEK LL FSTENERS FOR TIGHTNESS. HEK LIGNMENT OF FF RELTIVE TO THE MTING SE SELER OR ONVEYOR IN OTH THE HORIZONTL ND VERTIL DIRETIONS.. DJUST VEE WHEELS (PUSHER VERSION) TO ELIMINTE PLY.. HEK FLP FOLDER UMPERS FOR WER ND POSITION. PNUEMTI. HEK LL HOSES ND FITTINGS FOR LEKS OR DMGE.. HEK LL IR YLINDERS FOR WER. THE FLP FOLDER YLINDERS RE NON REUILDLE, THROWWY TYPE. REPLE S NEESSRY. THE PUSHER YLINDER IS REUILDLE. SEE THE REOMMENDED SPRE PRTS LIST TO ORDER REUILD KIT.. HEK FOR TIGHTNESS ND PROPER FUNTION OF LL OF THE MNULLY TUTED VLVES INLUDING THE FLP FOLDER VLVE, THE RESET VLVE, THE PUSHER VLVE ND THE E STOP VLVE. REPLE NY MLFUNTIONING VLVE.. HEK THE IR FILTER. LEN THE ELEMENT S NEESSRY.. SET IR PRESSURE TO 0 P.S.I. ELETRIL. HEK LL WIRES FOR GOOD ONNETION ND INSULTION.. HEK THE EXIT PHOTO EYE FOR SENSITIVITY, LIGNMENT ND TIMING. REFER TO INSTRUTIONS IN SETION
HPTER : TROULE SHOOTING OX DOESN T FOLD PROPERLY. MKE SURE OX IS ENTERED OVER TEE RIL EFORE UMPING OX GINST FLP FOLDER SWITH.. MKE SURE OX IS SITTING FLT ON TEE RIL.. REVIEW THEORY OF OPERTION SETION FOR ORRET SEQUENE OF TIONS TO FORM OX. FLP FOLDERS DON T TUTE. HEK TO SEE THT IR SUPPLY IS ONNETED, SHUT OFF VLVE IS TURNED ON, IR REGULTOR SET TO 0 PSI, ND E STOP UTTON IS PULLED UP.. IS FLP FOLDER VLVE FUNTIONL? TRY TUTING Y HND. DJUST POSITION OF VLVE OR REPLE S NEESSRY.. HEK IR FLOW ONTROLS ON THE FLP FOLDER YLINDERS. DJUST S NEESSRY. E SURE TO TIGHTEN LOK NUTS FTER DJUSTING.. PERFORM LOK OUT/TG OUT OF ELETRIL POWER ND IR SUPPLY THEN HEK FOR NY MEHNIL OSTRUTION. FLP FOLDERS DON T RETRT. DOES MHINE HVE ELETRIL POWER?. PHOTO EYE (PE) IS PIKING UP INDVERTENT SIGNL: a) HEK TO SEE IF SOMETHING IS LOKING THE FIELD OF THE PE. b) DJUST NGLE OF PE TO VOID PIKING UP MHINE OMPONENTS. c) REDUE SENSITIVITY OF PE (SEE PPENDIX).. HEK SOLENOID VLVE FOR PROPER FUNTION: a) IS DIN ONNETOR TIGHT? b) IS VLVE STIKING? TEST Y PRESSING MNUL OVERIDE. c) REPLE VLVE IF NEESSRY. PERFORM LOK OUT/TG OUT OF ELETRIL POWER ND IR SUPPLY THEN HEK FOR NY MEHNIL OSTRUTION. OX PUSHER (OPTIONL) DOES NOT MOVE FORWRD OR RETRT. IS LOD TOO HEVY? INRESE IR PRESSURE (0 PSI MX.). PNEUMTI VLVE MLFUNTION: REPLE.. IR YLINDER LEKING: REPLE.. PERFORM LOK OUT/TG OUT OF ELETRIL POWER ND IR SUPPLY THEN HEK FOR NY MEHNIL OSTRUTION. OX QULITY ISSUES. ORNERS OF FLPS RE URLING: a) RE FLP FOLDING PNELS OMING UP LL THE WY? DJUST Y REMOVING YLINDER GURD ND ROTTING SHFT LMP. b) RE RMPS PROPER DJUSTED? SET TOP OF RMPS TNGENT TO THE EXIT ROLLERS. c) RE EXIT ROLLERS SET TO THE RIGHT HEIGHT RELTIVE TO THE SE SELER OR ONVEYOR? a. TOP OF ROLLERS SHOULD E EVEN WITH WORKING SURFE OF NEXT MHINE. d) IS THE MHINE T THE ORRET HEIGHT RELTIVE TO THE SE SELER OF ONVEYOR? a. TOP OF TEE RIL SHOULD E / TO / HIGHER THN WORKING SURFE OF NEXT b. MHINE.
HPTER : WRRNTY Little David Warranty For: SE FORMER MODELS F-T, F0-T, F0T-XL MODELS YER WRRNTY ON DRIVE MOTOR YER WRRNTY ON GER REDUER YER WRRNTY ON TPE RTRIDGE (EXEPT FOR MOVING PRTS THT RE SUJET TO NORML WER, TER ND REPLEMENT, WHIH RE WRRNTED ONLY TO E FREE FROM DEFETS IN MTERIL ND WORKMNSHIP.) YER ON PL YER LL OTHER PRTS (EXEPT FOR WER ND MOVING PRTS.) For: SE FORMER MODELS F & FF YER ON PL YER LL OTHER PRTS (EXEPT FOR WER ND MOVING PRTS.) *LIMITED WRRNTY LOVESHW, WRRNTS ONLY THT THE GOODS SOLD Y IT SHLL E FREE FROM DEFETS IN MTERIL ND WORKMNSHIP, UNDER PROPER ND NORML USE ND MINTENNE, S FOLLOWS: DRIVE MOTOR - YER GER REDUER - YER TPE RTRIDGE - YERS (EXEPT FOR MOVING PRTS THT RE SUJET TO NORML WER, TER ND REPLEMENT, WHIH RE WRRNTED ONLY TO E FREE FROM DEFETS IN MTERIL ND WORKMNSHIP.) PL - YER LL OTHER PRTS - YER (EXEPT FOR MOVING PRTS THT RE SUJET TO NORML WER, TER ND REPLEMENT, WHIH RE WRRNTED ONLY TO E FREE FROM DEFETS IN MTERIL ND WORKMNSHIP.) THE WRRNTY PERIOD SHLL OMMENE S OF THE DTE OF DELIVERY TO THE PURHSER. THE OLIGTION OF LOVESHW UNDER THIS WRRNTY IS STRITLY LIMITED TO THE OST OF REPIRING OR REPLING, S LOVESHW MY ELET, NY PRT OR PRTS THT PROVE IN LOVESHW S JUDGMENT TO HVE EEN DEFETIVE IN MTERIL OR WORKMNSHIP T THE TIME THE GOODS WERE SHIPPED FROM LOVESHW S PLNT. NY WRRNTY LIM NOT MDE IN WRITING TO LOVESHW T ITS HOME OFFIE WITHIN THE PPLILE WRRNTY PERIOD ND WITHIN 0 DYS OF FILURE WILL NOT E VLID. THIS IS THE SOLE ND EXLUSIVE REMEDY VILLE UNDER THIS WRRNTY. UNDER NO IRUMSTNES WILL LOVESHW E LILE FOR INIDENTL, SPEIL OR ONSEQUENTIL DMGES. IF REQUESTED Y LOVESHW, PURHSER SHLL RETURN NY DEFETIVE PRT OR PRTS TO LOVESHW S PLNT, FREIGHT PREPID. LL WRRNTY PRT REPLEMENTS ND REPIRS MUST E MDE Y LOVESHW OR LOVESHW UTHORIZED TO HNDLE THE GOODS OVERED Y THIS WRRNTY. NY OUTSIDE WORK OR LTERTIONS DONE WITHOUT LOVESHW S PRIOR WRITTEN PPROVL WILL RENDER THIS WRRNTY VOID. LOVESHW, WILL NOT SSUME NY EXPENSE OR LIILITY FOR NY REPIRS MDE TO ITS GOODS OUTSIDE ITS WORKS WITHOUT ITS PRIOR WRITTEN ONSENT. THIS WRRNTY SHLL NOT PPLY TO NY ITEM THT HS NOT EEN USED, OPERTED, ND MINTINED IN ORDNE WITH LOVESHW S REOMMENDED PROEDURES LOVESHW SHLL HVE NO LIILITY WHTSOEVER WHERE THE GOODS HVE EEN LTERED, MISUSED, USED OR INVOLVED IN N IDENT. NO PERSON IS UTHORIZED TO MKE NY WRRNTY OR TO RETE NY LIILITY INDING UPON LOVESHW. WHIH IS NOT STTED IN THIS WRRNTY. THIS WRRNTY IS EXPRESSLY IN LIEU OF LL OTHER WRRNTIES OF NY KIND, EXPRESSED OR IMPLIED, WHIH RE HEREY EXLUDED. IN PRTIULR, THE IMPLIED WRRNTY OF MERHNTILITY, S WELL S THE IMPLIED WRRNTY OF FITNESS FOR PRTIULR PURPOSE RE HEREY EXLUDED. LOVESHW 0 ESTON TURNPIKE, OX SOUTH NN, P TEL: 0.. - 00.. - FX: 0..
HPTER : MHINE OMPONENTS
D ITEM 0 0 Parts List QTY PRT NUMER RFF-00- RFF-00- RFF-00- RFF-00R- RFF-00L- RFF-000R- RFF-000L- RFF-000- RFF-000- RFF-000R- RFF-000L- RFF-000- RFF-000- FLWMIP FLWMHP FHHMI00P FHHMH00P0 FHHMH0P0 FHHMG0P0 FHFNMIP FHFNMHP FFWMHP FFWMGP RFF-00- DESRIPTION END PNEL, FRONT UMPER, FLP FOLDER R, FLP REST SIDE PNEL SIDE PNEL GURD, YLINDER, RIGHT GURD, YLINDER, LEFT END PNEL, RER MHINE LEG V-SPR, FRME V-SPR, FRME END PLTE MIN EM LOK WSHER M0 LOK WSHER M HHS M0 X 0 HHS M X 0 HHS M X HHS M X HEX NUT M0 HEX NUT M FLT WSHER M FLT WSHER M RKET, ONTROL STTION 0 REVISION HISTORY DESRIPTION DTE REV Y RELESED //0 RM D 0 0 MT'L PRT # STD D FILE.FRFR.idw PLOT DTE /0/0 TOLERNES UNLESS OTHERWISE NOTED: LOVESHW an ITW ompany RT., SOUTH NN, P. ST. ST. STINLESS : NO FINISH DRWN DTE //0 DO NOT SLE PRINT THIS DRWING ND SUJET MTTER THEREON IS THE EXLUSIVE PROPERTY OF LOVESHW-ITW ND IS TO E TRETED Y YOU S ONFIDENTIL PRPRIETRY INFORMTION. THIS DRWING OR SUJET MTTER THEROF SHLL NOT E REPRODUED OTHER THN FOR YOUR OWN USE OR TO E DISLOSED TO OTHER WITHOUT THE EXPRESSED WRITTEN ONSENT OF LOVESHW-ITW ND WILL E RETURNED TO LOVESHW-ITW UPON REQUEST..X = + -.00 TITLE INH.XX = + -.0 NGLES + - / -.00.X = + -.0mm MH. METRI.XX = + -.mm DWG NO FINISH.FRFF -.mm MTERIL NOTED FRTIONS + - / DRWN richm FRME, FF SLE : HEKED PPROVED
D ITEM 0 Parts List QTY PRT NUMER DESRIPTION RG-00 FLNGE ERING FHMF0P0 HS M X FFWMGP FLT WSHER M FHFNMGP HEX NUT M FHHMG0P0 HHS M X FHJNSMP /-0 HEX JM NUT FLWMGP LOK WSHER M FSS00S0 SHD SR / x LG, 0- THRD FSHMG00P0 SHS M X 0 RFF-00- SHFT, FLP FOLDER RFF-00- LMP, FLP FOLDER RFF-00- MOUNT, YLINDER RFF-000- PNEL, FLP FOLDER SPH-0 ROD END, SPHERIL SPH- DOWEL PIN, / X " N00-0 FLOW ONTROL, TMPER PROOF REVISION HISTORY DESRIPTION DTE REV Y RELESED //0 RM D 0 0 MT'L PRT # STD D FILE.FFFF.idw PLOT DTE //0 TOLERNES UNLESS OTHERWISE NOTED: LOVESHW an ITW ompany RT., SOUTH NN, P. ST. ST. STINLESS : NO FINISH DRWN DTE //0 DO NOT SLE PRINT THIS DRWING ND SUJET MTTER THEREON IS THE EXLUSIVE PROPERTY OF LOVESHW-ITW ND IS TO E TRETED Y YOU S ONFIDENTIL PRPRIETRY INFORMTION. THIS DRWING OR SUJET MTTER THEROF SHLL NOT E REPRODUED OTHER THN FOR YOUR OWN USE OR TO E DISLOSED TO OTHER WITHOUT THE EXPRESSED WRITTEN ONSENT OF LOVESHW-ITW ND WILL E RETURNED TO LOVESHW-ITW UPON REQUEST..X = + -.00 TITLE INH.XX = + -.0 NGLES + - / -.00.X = + -.0mm MH. METRI.XX = + -.mm DWG NO FINISH.FFFF -.mm MTERIL FRTIONS + - / DRWN richm FLP FOLDER SSY, FF SLE : HEKED PPROVED
D ITEM 0 QTY PRT NUMER FFWMGP FFWMHP FHFNMGP FHFNMHP FHHMG00P0 FHHMH00P0 FLWMGP FLWMHP RFF-000- RFF-00L- RFF-00R- RFF-00L- RFF-00R- FHHMG0P0 N00- Parts List DESRIPTION FLT WSHER M FLT WSHER M HEX NUT M HEX NUT M HHS M X 0 HHS M X 0 LOK WSHER M LOK WSHER M TEE RIL SSEMLY RKET, ENTER TEE, LEFT RKET, ENTER TEE, RIGHT RMP, LH RMP, RH HHS M X /" ULKHED PUSH LOK REVISION HISTORY DESRIPTION DTE REV Y RELESED //0 RM D MT'L PRT # STD D FILE.TRMFF.idw TOLERNES UNLESS OTHERWISE NOTED: PLOT DTE //0 LOVESHW an ITW ompany RT., SOUTH NN, P. 0 ST. ST. DRWN DTE //0 STINLESS : NO FINISH DO NOT SLE PRINT THIS DRWING ND SUJET MTTER THEREON IS THE EXLUSIVE PROPERTY OF LOVESHW-ITW ND IS TO E TRETED Y YOU S ONFIDENTIL PRPRIETRY INFORMTION. THIS DRWING OR SUJET MTTER THEROF SHLL NOT E REPRODUED OTHER THN FOR YOUR OWN USE OR TO E DISLOSED TO OTHER WITHOUT THE EXPRESSED WRITTEN ONSENT OF LOVESHW-ITW ND WILL E RETURNED TO LOVESHW-ITW UPON REQUEST..X = + -.00 TITLE INH.XX = + -.0 NGLES + - / -.00.X = + -.0mm MH. METRI.XX = + -.mm DWG NO FINISH.TRMFF -.mm MTERIL FRTIONS + - / DRWN richm TEE RIL, MNUL VERSION SLE HEKED : PPROVED
D ITEM 0 0 QTY PRT NUMER 0 FFWMFP FFWMGP FHHMF0P0 FHHMF00P0 FHHMG00P0 FHHMH0P0 FLWMEP 0 FLWMFP FLWMHP FNLNMGP FSHME0P0 N0-0 PF- RFF-000- RFF-00- RFF-00- RFF-00- RFF-00- RFF-00- RFF-00- N00- Parts List DESRIPTION KNO, /- FLT WSHER M FLT WSHER M HHS M X HHS M X 0 HHS M X 0 HHS M X LOK WSHER M LOK WSHER M LOK WSHER M NYLOK NUT M SHS M X VLVE, ROLLER ELOW, / NPT X / PUSH LO SE, PUSHER GUIDE, RRIGE SPRING PIN SSEMLY FOLDING LOK K PNEL, FOLDING LOK GUIDE, OX ENTERING SLIDE, OX ENTERING GUIDE /" ULKHED PUSH LOK REVISION HISTORY DESRIPTION DTE REV Y RELESED //0 RM D 0 0 MT'L PRT # STD D FILE.FFF.idw PLOT DTE //0 TOLERNES UNLESS OTHERWISE NOTED: LOVESHW an ITW ompany RT., SOUTH NN, P. ST. ST. STINLESS : NO FINISH DRWN DTE //0 DO NOT SLE PRINT THIS DRWING ND SUJET MTTER THEREON IS THE EXLUSIVE PROPERTY OF LOVESHW-ITW ND IS TO E TRETED Y YOU S ONFIDENTIL PRPRIETRY INFORMTION. THIS DRWING OR SUJET MTTER THEROF SHLL NOT E REPRODUED OTHER THN FOR YOUR OWN USE OR TO E DISLOSED TO OTHER WITHOUT THE EXPRESSED WRITTEN ONSENT OF LOVESHW-ITW ND WILL E RETURNED TO LOVESHW-ITW UPON REQUEST..X = + -.00 TITLE INH.XX = + -.0 NGLES + - / -.00.X = + -.0mm MH. METRI.XX = + -.mm DWG NO FINISH.FFF -.mm MTERIL FRTIONS + - / DRWN richm FOLDING LOK, FF SLE : HEKED PPROVED
D ITEM 0 NS QTY PRT NUMER N0- N0- N0- N00- PF- PF- N00- N00- N/ N0 N PF-0 PF- N0- N0- RFF-00- H0 N Parts List DESRIPTION MNIFOLD, STTION VLVE, IR PILOTED VLVE SOL / MUFFLER PLUG, HEX SO PIPE, / NPT ELOW, / NPT X / PUSH LO ELOW, / NPT X / PUSH LO WYE, / NPT X / PUSH-LO RKET VLVE, MNUL LOK-OUT FILTER/REGULTOR, 0-0 PSI, / NPT RSS STREET ELOW, 0, / NPT QUIK DISONNET PLUG, / NPT VLVE, MNULLY OPERTED VVLE, PUSH UTTON WSHER, MNUL VLVE PLUG, HEX, / NPT OIL HOSE, MULTI-ORE, /" REVISION HISTORY DESRIPTION DTE REV Y RELESED //0 RM D SETION - SLE : 0 VIEW - NOTE:. USE PIPE THRED SELNT ON LL FITTINGS. MT'L PRT # D FILE.PNEUFFM-.idw TOLERNES UNLESS STD OTHERWISE NOTED: PLOT DTE //0.X = +.00 ST. ST. - DRWN DTE TITLE //0 INH.XX = + -.0 NGLES + - / -.00 STINLESS : NO FINISH DO NOT SLE PRINT.X = + -.0mm THIS DRWING ND SUJET MTTER THEREON IS THE EXLUSIVE PROPERTY OF MH. METRI.XX = + -.mm DWG NO FINISH.PNEUFFM LOVESHW-ITW ND IS TO E TRETED Y YOU S ONFIDENTIL PRPRIETRY INFORMTION. THIS DRWING OR SUJET MTTER THEROF SHLL NOT E -.mm REPRODUED OTHER THN FOR YOUR OWN USE OR TO E DISLOSED TO OTHER MTERIL WITHOUT THE EXPRESSED WRITTEN ONSENT OF LOVESHW-ITW ND WILL E RETURNED TO LOVESHW-ITW UPON REQUEST. FRTIONS + - / DRWN richm LOVESHW an ITW ompany RT., SOUTH NN, P. PNEUMTI SSEMLY FF MNUL VERSION SLE : HEKED PPROVED
REVISION HISTORY DESRIPTION DTE REV Y RELESED //0 JF D D Parts List 0 0 ITEM 0 0 0 0 QTY PRT NUMER FHFNMHP FLWMGP FSHMG00P0 RL-0 RFF-00- RFF-000- RFF-00L- RFF-00R- RFF-00- RG-0 RFF-00- RG-0 FHJNMGP RFF-000- N0-0 FSSJ000 SPH- TS0-0-0- P0-S- RG-0 N0 RFF-00L- RFF-00R- FHHMG0P0 FFWMGP FHFNMGP SP-0 RFF-00-.FFR HOK PUSHER N00- FHHMG00P0 FSHMF0P0 FSHMF00 SPH- FNLNMIP N FLWMFP FLWMIP FFWMIP FHHMI0P0 FHHMG0P0 FFWMHP FHHMH00P0 FLWMHP DESRIPTION HEX NUT M LOK WSHER M SHS M X 0 VEE WHEEL, STUDDED T, RRIGE SLIDE STRIP RKET, ENTER TEE, LEFT RKET, ENTER TEE, RIGHT PUSHER RM ROD END, M MLE TEE RIL SSY, VEE-TRK MOUNTED ERING, /" M HEX JM NUT SE, PUSHER YLINDER, 0mm X." S / DI. x L x /- THRD UMPER, URETHNE LINER SHFT, 0mm X 0mm ERING, PILLOW LOK ROD END, /", FEMLE, /-0 THRD. PIVOT RKET RMP, LH RMP, RH HHS M X FLT WSHER M HEX NUT M OLLR 0mm ID PUSH ROD GURD FOLDING LOK SSEMLY, FF /" ULKHED PUSH LOK HHS M X 0 SHS M X 0. - MM LG. M X mm SHS SHOULDER OLT M0 x 0mm NYLOK NUT M0 FLOW ONTROL, / NPT X / TUE LOK WSHER M LOK WSHER M0 FLT WSHER M0 HHS M0 X HHS M X FLT WSHER M HHS M X 0 LOK WSHER M 0 0 MT'L PRT # STD D FILE TRPFR.idw PLOT DTE TOLERNES UNLESS OTHERWISE NOTED: LOVESHW 0 ESTON TPK., SOUTH NN, P. ST. ST. STINLESS : NO FINISH DRWN DTE //0 DO NOT SLE PRINT THIS DRWING ND SUJET MTTER THEREON IS THE EXLUSIVE PROPERTY OF LOVESHW ND IS TO E TRETED Y YOU S ONFIDENTIL PRPRIETRY INFORMTION. THIS DRWING OR SUJET MTTER THEROF SHLL NOT E REPRODUED OTHER THN FOR YOUR OWN USE OR TO E DISLOSED TO OTHER WITHOUT THE EXPRESSED WRITTEN ONSENT OF LOVESHW ND WILL E RETURNED TO LOVESHW UPON REQUEST..X = + -.00 TITLE INH.XX = + -.0 NGLES + - / -.00.X = + -.0mm MH. METRI.XX = + -.mm DWG NO FINISH -.mm MTERIL FRTIONS + - / DRWN PUSHER SSEMLY, FF brycef SLE HEKED PPROVED
HPTER 0: SHEMTIS
HPTER : MHINE VILLE SPEIL OPTIONS FULL STINLESS STEEL ONSTRUTION PNEUMTILLY POWERED SE PUSHER LNK HOLDER USTOM ONNETION KITS STERS SPRE PRTS KIT ONTT YOUR LITTLE DVID DISTRIUTOR OR LL OUR FTERMRKET DEPRTMENT T 00 TO INQUIRE OUT SPEIL OPTIONS.
ITEM QTY Parts List PRT NUMER SEE HRT LD- FHJNSPP DESRIPTION STUD, /- X " LEVELING PD /- HJN REVISION HISTORY REV DESRIPTION DTE PPROVED RELESED //0 TONYS SSY. NO..LPFFM.LPFF/ PRT NO SPH- SPH-/ ONV. HEIGHT RNGE. to.0. to.0 MT'L NOTED ST. ST. N/ PRT # STD STINLESS : NO FINISH THIS DRWING ND SUJET MTTER THEREON IS THE EXLUSIVE PROPERTY OF LOVESHW ND IS TO E TRETED Y YOU S ONFIDENTIL PRPRIETRY INFORMTION. THIS DRWING OR SUJET MTTER THEROF SHLL NOT E REPRODUED OTHER THN FOR YOUR OWN USE OR TO E DISLOSED TO OTHER WITHOUT THE EXPRESSED WRITTEN ONSENT OF LOVESHW ND WILL E RETURNED TO LOVESHW UPON REQUEST. D FILE.LPFFM.idwTOLERNES UNLESS PLOT DTE //0 OTHERWISE NOTED:.X = + -.00 DRWN DTE TITLE //0 INH.XX = + -.0 NGLES + - / DO NOT SLE PRINT -.00.X = + -.0mm MH. METRI.XX = + -.mm DWG NO FINISH.LPFFM -.mm MTERIL NOTED FRTIONS + - / DRWN tonys LOVESHW 0 ESTON TPK., SOUTH NN, P. LEVELER PD SSEMLY SLE N/ HEKED PPROVED TONYS