Van Guard Bulkhead Test Report A257S01 If you have any questions relating to this test please contact your Project Manager: Mr A Thompson direct line + 44 (0)1344 770050 fax: + 44 (0)1344 770356 email: athompson@trl.co.uk switchboard: + 44 (0)1344 773131 website: http://www.trl.co.uk/ Copyright TRL March 11. All rights reserved. This is an unpublished report prepared for the customer named above and must not be referred to in any publication without the permission of the customer. The views expressed are those of the author(s) and not necessarily those of the customer Test Engineers C Walker / A Thompson Quality review S Ahmed TRL Limited, Registered in England, Number 3142272 Registered Offices: Crowthorne House, Nine Mile Ride, Wokingham, Berkshire, RG40 3GA, United Kingdom. A member of the Transport Research Foundation Group of Companies. Page 1 of 7
Van Guard Bulkhead Test Contents Summary... 3 A257S01... 4 Test Details... 4 Test Requirements... 4 Test Object... 4 Test Setup... 4 Test Observations... 6 Visual Documentation... 7 Page 2 of 7
SUMMARY A static loading test based on the requirements of BS ISO 27956:2009 was undertaken on an aftermarket van bulkhead produced by Van Guard at TRL on the 17 th February 2011. Customer Test Facility Test Number Van Guard Impact Sled Facility / Squeeze Rig A257S01 Test Date 17/02/2011 TRL Test Engineers Report Author Chris Walker / Alex Thompson Alex Thompson Page 3 of 7
A257S01 Test Details Test Procedure Based on BS ISO 27956:2009 Test Description Test Object Test Mass Applied Force Test Requirements Type 1 static load test Punched steel bulkhead 925 kg 9.07 kn BS ISO 27956:2009 states that a bulkhead should be able to withstand a force equivalent to half of the maximum payload of the vehicle multiplied by 1g, with permanent deformation of the bulkhead not exceeding 300mm. The standard specifies a force applied horizontally using a 1m x 1m square plunger piston to a bulkhead mounted in a van body. However, an equivalent test is to mount the bulkhead horizontally in a rigid frame representative of the installation in a van and apply a vertical load using a 1m x 1m mass. This was the test type used in this case. Test Object The test object used in this test was a sheet steel bulkhead with a punched section at the upper part of the bulkhead. The bulkhead was a vehicle-specific design intended for use in the Peugeot Boxer / Fiat Ducato / Citroën Relay ( 06 on) van models, where the largest variant (L4) has a maximum payload of 1850kg. Test Setup The bulkhead was mounted in the test rig on a rigid frame representative of the fitment in the van. Two displacement transducers were attached to the underside of the bulkhead to measure the deformation of the bulkhead during the test. Page 4 of 7
The required force to be applied to the bulkhead was calculated as follows: Where F = 0.5 x m p x g F is the test force in N m p is the maximum payload in kg g is the acceleration due to gravity (9.81 m/s 2 ) Therefore F = 0.5 x 1850 x 9.81 = 9074.25 N This force can be applied vertically by a mass of 925 kg under the influence of gravity. The force was applied to the centre of the bulkhead, which was measured according to its maximum height and width as shown in the photographs below: Page 5 of 7
Deformation (mm) Test Observations The following observations were made during the test: The full force was applied within 2 seconds of first loading The load was applied for a time period in excess of 10 seconds The bulkhead deformation was measured to a peak level of 183.1mm at the upper part of the bulkhead during the test, which reduced to 177.1mm once the load had stabilised The load was removed from the bulkhead and there was some spring back of the bulkhead, resulting in a permanent measured deformation of 151.1mm All of the recorded deformation values were well within the limit of 300mm for permanent deformation as specified in the standard. 0-50 -100 0 5 10 15 20 25 30 Van Guard Bulkhead Test Punched steel bulkhead A257S01 17/02/2011 9.07 kn Applied force Test Engineer: A Thompson -150-200 -250-300 Time (s) Bulkhead centre Bulkhead upper Peak deformation Centre: 154.3 mm Upper: 183.1 mm Stabilised deformation (under load) Centre: 150.0 mm Upper: 177.1 mm Permanent deformation (unloaded) Centre: 118.7 mm Upper: 151.1 mm No sharp edges or other deformations were observed on the bulkhead during or after the test which may directly or indirectly result in injuries to the vehicle occupants. Page 6 of 7
Visual Documentation Pre and post test still photographs of the bulkhead test can be found in the folder A257S01/Stills on the test CD. Real time video of the bulkhead test can be found in the A257S01/Video folder on the test CD. Page 7 of 7