Supersonic Combustion of Liquid Hydrogen using Slotted Shaped Pylon Injectors

Similar documents
Design Rules and Issues with Respect to Rocket Based Combined Cycles

Supersonic Combustion Experimental Investigation at T2 Hypersonic Shock Tunnel

Analysis of Scramjet Engine With And Without Strut

Design Rules and Issues with Respect to Rocket Based Combined Cycles

Scramjet Engine Research of KARI : Ground Tests of Engines and Components

Numerical simulation of detonation inception in Hydrogen / air mixtures

K. P. J. Reddy Department of Aerospace Engineering Indian Institute of Science Bangalore , India.

PERFORMANCE ESTIMATION AND ANALYSIS OF PULSE DETONATION ENGINE WITH DIFFERENT BLOCKAGE RATIOS FOR HYDROGEN-AIR MIXTURE

Experimental Research on Hydrogen and Hydrocarbon Fuel Ignition for Scramjet at Ma=4

COMPUTATIONAL ANALYSIS DIAMOND-SHAPED STRUT INJECTOR FOR SCRAMJET COMBUSTOR AT MACH 4.3 S. Roga1,K.M. Pandey2 and A.P.Singh3 1

In this lecture... Components of ramjets and pulsejets Ramjet combustors Types of pulsejets: valved and valveless, Pulse detonation engines

FLUIDIC THRUST VECTORING NOZZLES

CFD Analysis on a Different Advanced Rocket Nozzles

Plasma Assisted Combustion in Complex Flow Environments

Silencers. Transmission and Insertion Loss

Design Fabrication And Performance Analysis Of Subsonic RAMJET Engine

DESIGN AND TESTING OF A DUAL-MODE SCRAMJET FOR OPTICAL MEASUREMENT TECHNIQUES

Study of Inlet Guide Vanes for Centrifugal Compressor in Miniature Gas-Turbines

Numerical Simulation on the Pattern Factor of the Annular Combustor

Comparison of Efficiency of Conventional Shaped Circular and Elliptical Shaped Combustor

AERODYNAMIC PERFORMANCES OF THE COMBINED CYCLE INLET

NON-PREMIXED CONDITIONS IN THE FLAMEHOLDING RECIRCULATION REGION BEHIND A STEP IN SUPERSONIC FLOW

COMPUTATIONAL ANALYSIS OF SUPERSONIC COMBUSTION USING CAVITY BASED FUEL INJECTION WITH SPECIES TRANSPORT MODEL AT MACH NUMBER 4.

Dean Andreadis Pratt & Whitney Space Propulsion, Hypersonics, West Palm Beach, FL,

Australian Journal of Basic and Applied Sciences

AE Aircraft Performance and Flight Mechanics

CFD Analysis of Single and Double Cavity Based Scramjet Combustion with Front Ramp Angle at Mach 2

Computational Analysis of Hydrogen-Fueled Scramjet Combustor with Diamond-Shaped Strut Injector at Mach 4

SWIRL MEASURING EQUIPMENT FOR DIRECT INJECTION DIESEL ENGINE

Ignition delay studies on hydrocarbon fuel with and without additives

Numerical Simulation of Gas Turbine Can Combustor Engine

Numerical Simulation of Cavity Fuel Injection and Combustion for Mach Scramjet. Dora E. Musielak University of Texas at Arlington

The spray characteristic of gas-liquid coaxial swirl injector by experiment

EFFECT OF INJECTION ORIENTATION ON EXHAUST EMISSIONS IN A DI DIESEL ENGINE: THROUGH CFD SIMULATION

Experimental Testing of a Rotating Detonation Engine Coupled to Nozzles at Conditions Approaching Flight

Comparison of Swirl, Turbulence Generating Devices in Compression ignition Engine

PERFORMANCE EVALUATION OF A FOUR STROKE COMPRESSION IGNITION ENGINE WITH VARIOUS HELICAL THREADED INTAKE MANIFOLDS

1.1 The Ramjet and the Supersonic Combustion Ramjet (Scramjet) Engine Cycle

Supersonic Combustion Flow Visualization at Hypersonic Flow

Observation of Flame Stabilized at a Hydrogen-Turbojet-Engine Injector Installed into a Lab-Scale Combustion Wind Tunnel

Gujarat, India,

The SABRE engine and SKYLON space plane

Methods for Reducing Aerodynamic Drag in Vehicles and thus Acquiring Fuel Economy

Fig 2: Grid arrangements for axis-symmetric Rocket nozzle.

EXPERIMENTAL STUDIES OF INJECTOR ARRAY CONFIGURATIONS FOR CIRCULAR SCRAMJET COMBUSTORS

PNEUMATIC BIKES ABSTRACT

OF THE FUTURE-THE PNEUMATIC BIKE ECO FRIENDLY

Fig. 2: Strut with circular injector [4] All rights reserved by 544

Marc ZELLAT, Driss ABOURI and Stefano DURANTI CD-adapco

ATOMIZATION AND COMBUSTION IN LOX/H 2 - AND LOX/CH 4 -SPRAY FLAMES. M. Oschwald 1, F. Cuoco 2, B. Yang 3, M. De Rosa 1

THE RIG STAND FOR TESTING INTEGRATED ROCKET RAMJET ENGINE

Effects of Dilution Flow Balance and Double-wall Liner on NOx Emission in Aircraft Gas Turbine Engine Combustors

REDUCTION OF EMISSIONS BY ENHANCING AIR SWIRL IN A DIESEL ENGINE WITH GROOVED CYLINDER HEAD

ALCOHOL LOX STEAM GENERATOR TEST EXPERIENCE

Investigation of converging slot-hole geometry for film cooling of gas turbine blades

The Prime Glass DeNOx solutions in the present scenario of the glass industry NOx containment technologies

IJSRD - International Journal for Scientific Research & Development Vol. 3, Issue 11, 2016 ISSN (online):

Fuel Injection and Combustion Study for Mach Scramjet. Dora E. Musielak University of Texas at Arlington

CFD Analysis of a Hydrogen Fueled Mixture in Scramjet Combustor with a Strut Injector by Using Fluent Software

LIQUID HYDROGEN AS AVIATION FUEL AND ITS RELATIVE PERFORMANCE WITH COMMERCIAL AIRCRAFTS FUEL

Experimental Investigation of Performance and Emission Characteristics of Hybrid Fuel Engine

The influence of shear layer control on DDT

CONTENTS Duct Jet Propulsion / Rocket Propulsion / Applications of Rocket Propulsion / 15 References / 25

HYDROCARBON AND HYDROGEN-FUELLED SCRAMJET CAVITY FLAMEHOLDER PERFORMANCE AT HIGH FLIGHT MACH NUMBERS

Dual-Mode Combustion of a Jet in Cross-Flow with Cavity Flameholder

IJESRT: 7(10), October, 2018 ISSN:

Numerical Analysis of External Supersonic Combustion of Hydrogen and Ethylene

Rotating Detonation Wave Stability. Piotr Wolański Warsaw University of Technology

OPTIMIZATION OF SCRAMJET COMBUSTOR WITH NORMAL AND TANGENTIAL FUEL INJECTION

PROPULSION. THE TECHNOLOGICAL revolution of the past - MANY ROADS GO UP. zrt -

Thermal Design And Analysis Of Regeneratively Cooled Thrust Chamber Of Cryogenic Rocket Engine

Combustion Equipment. Combustion equipment for. Solid fuels Liquid fuels Gaseous fuels

Study of Performance and Emission Characteristics of a Two Stroke Si Engine Operated with Gasoline Manifold Injectionand Carburetion

HY-V SCRAMJET INLET Christina McLane Virginia Polytechnic Institute and State University

DESIGN AND ANALYSIS OF UNDERTRAY DIFFUSER FOR A FORMULA STYLE RACECAR

Experimental Investigation on Diesel Engines by Swirl Induction with Different Manifolds

COMBUSTION in SI ENGINES

Aircraft Propulsion Technology

PROVISIONAL PATENT APPLICATION INVENTORS: RICHARD E. AHO CAVITATION ENGINE

A.S.P. Sri Vignesh 1, Prof C. Thamotharan 2 1 (Department of Automobile Engineering, Bharath Institute of Science and Technology, Bharath University

TECHNICAL PAPER FOR STUDENTS AND YOUNG ENGINEERS - FISITA WORLD AUTOMOTIVE CONGRESS, BARCELONA

Design Modification and Optimization of Trolley in an Off-Bearer Mechanism Present In Concrete Block Making Machines

INFLUENCE OF INTAKE AIR TEMPERATURE AND EXHAUST GAS RECIRCULATION ON HCCI COMBUSTION PROCESS USING BIOETHANOL

THE THEORETICAL STUDY ON INFLUENCE OF FUEL INJECTION PRESSURE ON COMBUSTION PARAMETERS OF THE MARINE 4-STROKE ENGINE

apply to all. space because it is an air-breather. Although from the atmosphere to burn its fuel. This limits

Module7:Advanced Combustion Systems and Alternative Powerplants Lecture 32:Stratified Charge Engines

EXTENDED GAS GENERATOR CYCLE

Case Study of Exhaust Gas Recirculation on Engine Performance

Metrovick F2/4 Beryl. Turbo-Union RB199

Recent Advances in Scramjet Fuel Injection - A Review

Shock wave assisted removal of micron size dust. particles from silicon wafer surfaces.

Overview of Dual-mode Operation of Scramjets

Development of a Non-Catalytic JP-8 Reformer

ia 451s, 10-y (12) Patent Application Publication (10) Pub. No.: US 2003/ A1 (19) United States Johnson et al. (43) Pub. Date: Feb.

PROPULSION SYSTEMS. bjectives

Make a great improvement of Engine fuel efficiency. Explanation

IAC-15-C4.3.1 JET INDUCER FOR A TURBO PUMP OF A LIQUID ROCKET ENGINE

Hypersonic Airbreathing Propulsion

Development of In-Line Coldstart Emission Adsorber System (CSEAS) for Reducing Cold Start Emissions in 2 Stroke SI Engine

Design and Analysis of Restricted Air Intake for Performance Optimization of Single-Cylinder Engine

Transcription:

Advances in Aerospace Science and Applications. ISSN 2277-3223 Volume 3, Number 3 (2013), pp. 131-136 Research India Publications http://www.ripublication.com/aasa.htm Supersonic Combustion of Liquid Hydrogen using Slotted Shaped Pylon Injectors Gokul.R and Mythri.M.S Department of Aeronautical Engineering, Rajalakshmi Engineering College, Thandalam, Chennai, India. Abstract Successful supersonic combustion has always been a dream-come true for all sonic enthusiasts for a huge number of applications, prime ones being hypersonic and ballistic missile defense, and air-breathing access to space like SSTOs (Single Stage To Orbit), reusable rockets, etc. In this paper, liquid hydrogen and its possibility as a fuel for scramjets has been studied. Also, fuel injection and injector jet geometries play a king s role in enhancing the combustion efficiency. A handful of different pylon injector geometries have been referred and studied. Keywords: Mach number, fuel injection, combustion efficiency, G mixing, OH fluorescence, Specific impulse. 1. Introduction Man has evolved greatly from stones to metal. Need to dominate the world both with power and technology drove the 20 th century scientists to unfold the most challenging arena of engineering- flying piece of metal. Ever since, the invention of the theories of lift and airfoil, flying was made possible, but not efficient. After the categorization of mach numbers, it is quite obvious that man will hop to pioneer high speed propulsion. Turbojets were invented and put into reality readily for subsonic vehicles. For a supersonic travel, even though enhancing the vehicle aerodynamically and structurally, engines were transformed from turbojets to ramjets. In ramjets, compression was achieved by formation of normal shock, which means the flow turns to be subsonic after the shock wave. This principle will not be friendly enough at higher mach numbers, say in an order of 5 or above. Hence we meet a new tricky technique of combustion, which is going to be at a supersonic speed.

132 Gokul.R & Mythri.M.S 1.1 Supersonic combustion: A Scramjet engine is well known as hypersonic air-breathing engine in which heat release due to combustion process occurs in a supersonic flow relative to the engine. Hence, the flow velocity throughout the engine remains supersonic. Here, the free stream is compressed by producing inclined (i.e., oblique) shock waves using isolators. At very high speeds, combustion has to be invariably supersonic. Reasons of which are as follows: If combusted at a subsonic speed using a normal shock, as in ramjets, the engine will suffer from a very high total pressure loss. Also, molecular dissociation will be appreciable, when we conduct combustion subsonically, while the inlet mach is hypersonic. 2. Why Liquid Hydrogen? Generally, kerosene is the working fuel for any air-breathing aero engine. But for a hypersonic vehicle, (above mach 7 or 8), kerosene does not seem to be a good choice, reasons worth penning. In this paper usage of cryogenic liquid hydrogen (which is at - 253 deg C), as a fuel has been studied. Kerosene, which has a high molecular mass, cannot be injected as such, into the incoming air stream. A proper atomization technique is inevitable. Hydrogen, being the lightest of all, does not have to be atomized separately to get ignited, as its auto ignition temperature is 571 deg C. Incoming supersonic free stream has a temperature way higher than this. Moreover, its ignition time time between injection and ignition, proves to be less compare to kerosene. Thus increasing combustion efficiency and also bringing down the required combustor length. Also beyond a high mach (say > 8 or 9), kerosene reached its flash point easily, making itself incapable to cool the vehicle. Liquid hydrogen, if managed to maintain its cryogenic temperature, will prove to be a good reliable cooling agent. Literature studies reveal that liquid hydrogen reduces the molecular weight of the exhaust gas and thus increases the specific impulse, despite incomplete combustion. Evidently, one of the main important receiving end of an efficient air-breathing hypersonic vehicle (scramjet powered) is SSTOs (Single Stage To Orbit). Arriving at the LEO (Low Earth Orbit), with a high orbiting speed, has always been with stage propulsion, usually non-air breathing, by carrying oxidizer and fuel separately in tanks. Utilization of an efficient air-breathing scramjet is believed to rocket the payload at one go, i.e., devoid of stages. Employing liquid hydrogen in a scramjet eliminates oxidizer space, thus pushing out a major term in weight calculation. 2.1 OH fluorescence: The emission of self-fluorescence of a flame consists of thermal fluorescence (thermal excitation of the molecules) and chemiluminescence (production of excited molecules by chemical reactions). By choosing a suitable molecule and knowing their role in the chemical kinetics involved, the kinetical processes can be examined. The highly reactive OH radicals are products of starting and chain branching reactions of the

Supersonic Combustion of Liquid Hydrogen using Slotted Shaped Pylon Injectors 133 hydrogen combustion process, subsequently serve as reaction partners for the exothermic fuel oxidation reactions and are finally consumed by chain terminating reactions. Therefore the detection of OH self-fluorescence is an appropriate means to determine location and intensity of the reaction zones. Comparing the OH fluorescence of the cases, viz., liquid hydrogen with LOX- liquid oxygen (non air breathing) and liquid hydrogen with atmospheric incoming air (2) we get even more technical insight of the advantage of using the latter in rocketing. Fig. 1 Fig.2 In the above graph, along X axis is the length of the wall of the combustor and along Z axis is the height of the combustor. Figure 1 represents the case of non air breathing combustion (LOX with LH2) and figure 2 represents the case of air breathing combustion ( LH2 with atm air). Injector is placed at the origin. 3. Injectors There are several important issues that have to be troubleshot while designing an efficient fuel injector, especially for supersonic combustion. Some bullet points are total pressure loss, mixing efficiency parameter (G mixing ) among which the formal have to be low and the latter-high. Also, careful crafting of the injector will help metering the combustion length and weight down the scale. 3.1Injector Types: Arriving at the injectors types, there are two main categories, namely, intrusive and non-intrusive. Intrusive ones are those whose geometry is included inside the combustor. Some of the intrusive types are strut, pylons, ramp, etc. On the other hand, non-intrusive ones are those that are not themselves included into the combustor working space. E.g. wall jet injectors.

134 Gokul.R & Mythri.M.S In this paper with a reference to the paper by C.Gruenig and his co-authors (3), a set of four different pylon injectors have been studied. 4. Pylon Injection Pylon injection is essentially an injection behind a tall, narrow in-stream body. Injection may be axial, normal, or at any angle relative to the free stream. By injecting the fuel in the center of the flow, with pylons, problem of slow lateral mass transport in supersonic mixing layers is circumvented. 4.1Tested pylon designs: 3 Various pylon designs have been tested with respect to their mixing and combustion performance. The fuel injection holes of the pylons were designed to give a mach of 1 at the exit. The orifices were sized to give approximately the same fuel mass flow rate for a selected injection pressure range. The chosen pylon designs are shown in fig.3. These pylons allow the study of the effects the injection angle, shape of the injection orifice, and the number of injected fuel jets. Pylons A, C and D inject a single fuel jet. Pylon B injects four jets. Pylons A and B inject circular jets and pylons C and D inject elliptical or slot-shaped jets. Mixing efficiency parameter is interpretated as the inverse of the fuel mass flux. Faster the fuel mass flux decreases along the combustor, better the mixing process.it can be given as,. G mixing of all the four pylons has been studied and is plotted in the graph in fig.4. Fig. 3: Tested pylons. 3

Supersonic Combustion of Liquid Hydrogen using Slotted Shaped Pylon Injectors 135 Fig. 4: G mixing of all four pylons. 3 Fig. 5: Optimized pylon(pylon B) 3 4.2Optimized pylon and its combustion performance: 3 Based on the results of mixing and combustion experiments, the pylon design is been optimized and is shown in fig.5. The pylon basically consists of a strut that is equipped with six small ramps that inject the fuel with a downstream angle of 30deg. By means of multiple injection orifices, the fuel is spread across the whole duct. 5. Conclusion From the above collective study, following inferences can be spot-lighted: i. Utilizing liquid hydrogen as a fuel in scramjets, as well as the active coolant, some serious limitations of employing hydrocarbon fuels can be obliterated. ii. Liquid hydrogen fuelled scramjet will rapidly reach very high mach numbers( above 8 or 9) so fast and easily, than a hydrocarbon counter part. iii. In the reffered paper for pylon injection, circular injection jets have been used, solely for budget reasons. If the finance be taken care of, integration of the cross section of pylon C(slot shaped) or D with the optimized pylon(pylon B) - wholly, a slot shaped multi jet pylon, might prove to be the most efficient choice, as it brings two advantages together - a) Most homogenous fuel distribution across the flow channel(pylon B) b) Faster expansion than circular jets.( slot shaped ones-pylons C and D) References [1] K.M.Pandey, Member IACSIT and T.Sivasakthivel., Recent advances in scramjet fuel injection- A review, International Journal of Chemical Engineering and Applications, Vol.1, No.4, Dec 2010. [2] Fabrizio Vergine, Luca Maddalena, Victor Miller and Mirko Gamba., Supersonic Combustion and Flame holding characteristics of Pylon injected Hydrogen in a Mach 2.4 High enthalpy flow, 50 th Aerospace Sciences Meeting and Aerospace exposition, 09-12 January 2012.

136 Gokul.R & Mythri.M.S [3] C.Gruenig, V.Avrashkov, and F.Mayinger, Fuel injection into a supersonic airflow by means of pylons, Journal of Propulsion and Power, Vol 16, No.1, January-february 2000.