SCOPE OF ACCREDITATION TO ISO/IEC 17025:2005 AUTONEUM NORTH AMERICA, INC. 29293 Haggerty Rd. Novi, MI 48331 Jian Pan Phone: 248 324 2264 MECHANICAL Valid To: October 31, 2017 Certificate Number: 1745.02 In recognition of the successful completion of the A2LA evaluation process, accreditation is granted to this laboratory to perform the following tests on automotive components, coatings, plastics, polymers, and textiles: Test Abrasion Linear Taber Adhesion Test/ Peel Bearding/ Snagging GMW 14125 (A2X2, BX2) ASTM D3884; SAE J1530 (except Section 5); GMW 3208; ISO 5470-1; FLTM BN 108-02 ASTM D903, D413; Chrysler LP-463LB-10-01; FLTM BN 151-05; GMW 14695, 16596 1, 16381 1 ; GM 9193P; DIN 53530, 53357; TL 52411 (6) 1 SAE J1530 Bending/ Impact FLTM BN 102-01; Ford WSS-M8P16-B 1 Cleanability Chrysler LP-463KC-04-01 (Procedure 1), LP-463KC-04-01 (Procedure 2); FLTM BN 112-08; TL 52094 (3.21) 1 ; GMW 3402, 16596 (Section 3.4.2.3) Cold Cracking/ Flexibility SAE J323 (Mandrel Method A); Chrysler LP-463DD-07-01 (Mandrel), LP463LB-11-01B, LP463LB-11-01A; FLTM BN 102-01; Ford WSS-M15P32-D 1, WSS-M15P6-D 1, WSS-M8P16-B 1, WSS-M5G52-B 1 ; GMW 14108, 16596 1, 14093 (Method C); DBL 5306 (7.2, 7.3) 1 Color Evaluation ISO 105-A02; AATCC Evaluation Procedure 1, Evaluation Procedure 2 (A2LA Cert. No. 1745.02) Revised 09/30/2017 Page 1 of 4
Test Compression SAE J1352; ASTM D3574 (Test D); ISO 1856, 3386-1; PV 3919 Corrosion SAE J1389 Crocking SAE J861; FLTM BN 107-01, BN 108-10; ISO 105-X12 (DIN EN ISO 105-X12); PV 3906 Density/ Specific Gravity ASTM D792 (Method A); ISO 1183 (Method A) Dye Transfer - Color Bleeding Dust-out Environmental Conditioning FLTM AN 101-01; Chrysler LP-463KC-1-01; GMW 14129 (Section 3.3.3) GM9635P Chrysler MS-HZ100 1, LP-463DD-08-02, LP463LB-12-01B; Ford WSS-M99P32-C 1, WSS-M15P32-D 1, WSS-M15P6-D 1, WSS-M8P16-B 1 ; GMW 14124 (Cycle R), 14124 (Cycle M), 3221 (Code A), 3026 1, 16596 1, 15757 1 ; ISO 2440; DBL 5471 (PV95-4.1) 1, 5463 (PV00-4.3.1) 1, 5972 (4.4) 1 ; VW PV 1200, 2005-A, 3904; TL 52306 (7.13) 1, TL 52411 (9) 1 Flammability ISO 3795; SAE J369; FMVSS 302; GMW 3232; Chrysler MS-JP9-4 1, LP-463DB-16-03; DBL 5307 (5.1) 1 ; Toyota TSM 0500G; GB 8410; TL 1010; DIN 75200 Fluid/ Chemical Resistance, Immersion Chrysler MS-HZ100 1 ; ASTM D896; FLTM BO 101-05; GMW 14194 1, 14196 1, 15725 (Table 3), 15725; TL 52306 (7.11) 1 Fogging Gravimetric Photometric SAE J1756; GMW 3235 (Method B) SAE J1756; Chrysler LP-463DB-12-01; GMW 3235 (Method A) Fungus/ Mildew Ford WSS-M99P32-C 1, WSS-M15P32-D 1, WSS-M15P6-D 1, WSS-M8P16-B 1, WSS-M15P44-B 1 ; GMW 3259 Hardness ASTM D2240 (Type A); ISO 868 Heat Aging (Exposure, Degradation) Chrysler LP463LB-13-01, MS-HZ100 (Hot Plate) 1 ; Ford WSS-M99P32-C 1, WSS-M15P32-D 1, WSS-M15P6-D 1, WSS-M99D63-A3 1, WSS-M8P16-B 1, WSS-M15P44-B 1, WSS-M15P37-B 1, WSS-M5G52-B 1 ; GMW 14194 1, 14196 1, 16381 1 ; DBL 5471 (PV95-4.2) 1, 5972 (4.3) 1 ; TL 52306 (7.4.1, 7.4.3) 1 (A2LA Cert. No. 1745.02) Revised 09/30/2017 Page 2 of 4
Test Humidity Exposure Chrysler LP463CB-10-01-A 2, MS-HZ-100 (Table 2) Moisture Content/ Water Absorption/ Thickness Swell Ford WSS-M99P32-C (Section 3.11); GMW 16381 1 ; TL 52094 (3.19) 1 Odor SAE J1351; FLTM BO 131-03, 131-01; GMW 3205; VDA 270; PV 3900 Salt Immersion Chrysler MS-JB2000 1, MS-JP1-3 1 Shrinkage/ Dimensional Stability ASTM D1204; SAE J883; FLTM BN 105-01, 105-03, BS 103-01B (using SAE J315 1 ); GMW 4217; DIN 53377, 53892-2; TL 52306 (7.4, 7.5) 1, 52094 (3.18) 1, 52411 (6.7) 1, 52499 (7.7, 7.8) 1, 52463 (3.1.2, 3.2.2, 3.3.2, 7.4) 1 Stain Resistance FLTM BN 103-01 Tear Strength "C" Block Method Tongue Method Trapezoid Method Trouser Method Tensile Strength Elongation Grab Method Elongation Dumbbell Method Thickness Tuft Lock Strength ASTM D624 (Die C), D1004; ISO 34-1 (Method B) ASTM D2261 ASTM D5733 (Withdrawn 2008) 3, D5587; ISO 9073-4; GMW 3326 ASTM D461 (Withdrawn 2004) 3, D3574 (Test F); ISO 13937-2; DIN EN ISO 13937-2; DIN 53356 ASTM D1117, D5034; GMW 3010 (Code A), 3010 (Code C); ISO 9073-3, 13934-1 ASTM D3574 (Test E), D412 (Dies A and C); ISO 37, 527 (Type 1A), 1798 ASTM D5736 Chrysler LP-463KB-22-01; ASTM D1335 Water Spotting/ Staining Chrysler LP-463KC-03-01; FLTM AN 101-01; Ford WSS-M99D63-A3 (Section 3.7.6); GMW 14102 Weight Loss Chrysler LP-463DD-04-01 (Section 7.1) (Volatile loss) Weight/ Mass ASTM D3776, D4611 (Withdrawn 2004) 3 ; SAE J860; FLTM BN 106-01; GMW 3182; DIN EN 12127, 29073-1; ISO 9073-1, 2286-2 Wicking (Water) SAE J913 (A2LA Cert. No. 1745.02) Revised 09/30/2017 Page 3 of 4
When applicable, all tests can be performed under any or all of the following conditions: Temperature High: (21 to 300) C Low: (-40 to 0) C Environmental Temperature: (21 to 150) C Humidity: (20 to 98) %RH Fogger Temperature/ heating: (50 to 120) C Temperature/ cooling: (20 to 40) C 1 This material specification is not an accredited test and the inclusion of this material specification on this Scope does not confer laboratory accreditation to the material specification nor does it confer accreditation for the method(s) embedded within the specification. The accredited test methods listed on this scope are used in determining compliance with this material specification. 2 Utilizing non-condensing humidity environmental chamber. 3 This laboratory s scope contains withdrawn or superseded methods. As a clarifier, this indicates that the applicable method itself has been withdrawn or is now considered historical and not that the laboratory s accreditation for the method has been withdrawn. (A2LA Cert. No. 1745.02) Revised 09/30/2017 Page 4 of 4
Accredited Laboratory A2LA has accredited AUTONEUM NORTH AMERICA, INC. Novi, MI for technical competence in the field of Mechanical Testing This laboratory is accredited in accordance with the recognized International Standard ISO/IEC 17025:2005 General requirements for the competence of testing and calibration laboratories. This accreditation demonstrates technical competence for a defined scope and the operation of a laboratory quality management system (refer to joint ISO-ILAC-IAF Communiqué dated 8 January 2009). Presented this 6 th day of July 2015. President & CEO For the Accreditation Council Certificate Number 1745.02 Valid to October 31, 2017 Revised September 30, 2017 For the types of tests to which this accreditation applies, please refer to the laboratory s Mechanical Scope of Accreditation.