OFFICE OF THE PRINCIPAL, GOVT. INDUSTRIAL TRAINING INSTITUTE,

OFFICE OF THE PRINCIPAL, GOVT. INDUSTRIAL TRAINING INSTITUTE, MATHILI, AT/PO: MATHILI, DIST: MALKANGIRI (ODISHA) PIN-764045 Email: principalitimathili@gmail.com No 104 /ITIMathili Dated 05.05.2015 QUOTATION CALL NOTICE FOR SUPPLY OF TOOLS & EQUIPMENTS Sealed Quotations are invited from reputed Manufacturers/Authorized Dealers/Distributors/ Suppliers/ having valid VAT clearance, TIN & PAN/TAN Registration for supply and installation of Tools, Equipments of reputed make to Govt, ITI, Mathili, Dist- Malkangiri under the Directorate of Technical Education & Training, Odisha, Cuttack. A complete set of Quotation documents containing the details of items in Package No. A,B & C with specification, terms and conditions can be obtaining from the OFFICE OF THE PRINCIPAL ITI MATHILI on working days between 10.00Am to 5.00Pm. The Quotation shall be submitted along with requisite amount of EMD 1 % of the total quoted value in the shape of Bank draft drawn in favor of the Principal ITI Mathili payable at Malkangiri in a sealed packets by speed post or registered post only or dropped in the quotation box.the quotation super scribing Quotation for T. &.E., Package No. _ in the top of the envelope & submitted latest by 04.06.2015 up to 10.00 AM The same will be opened at 10.30AM on 04.06.15. The Authority reserves the right to accept or reject any or all, full or part of Quotation without assigning any reason thereof. Sd/- Principal ITI Mathili Memo No. 105 / Dt 05.05.15 Copy to Institute Notice board for information to the Dealers/Distributors/ Suppliers & wide publicity of the quotation. Sd/- Principal ITI Mathili

GENERAL INFORMATIONS, TERMS AND CONDITIONS FOR THE BIDDERS. FOR SUPPLY OF TOOLS/EQUIPMENTS/MACHINERIES 1. The sealed Quotation invites for supply and installation of tools, equipments & machineries for Govt.I.T.I Mathili, SDC Kalimela & SDC Korkunda 2. Interested credible Bidders can obtain Complete set of Quotation documents from Office of the Principal ITI Mathili from 05.05.15 to 30.05.15 3. The Bidders are required to indicate the page no. and signature in each page with seal on each of the documents of the Quotation. Further they are required to quote rate against the item with make, model etc. supported with technical literature/leaflets wherever necessary. Failing which, the item shall be summarily rejected. 4. Bidder may quote for any one or more than one package should submit separate Quotation for each Package as in separate sealed cover super-scribing Quotation for T &.E of Package No... 5. The Bidder shall quote rate against the items mentioned with make and model in the package list considering that the make & model as an equivalent brand. However in case of non- specified brand items the Bidders have to quote rate mentioning the standard and quality authorized brand and the Quotations with out make & model shall be summarily rejected if that Item is having a specified brand. 6. The Quotation s h a l l be accompanied by the Earnest Money Deposit (refundable with out interest) against each package separately in shape of Bank Draft from SBI drawn in favour of the Principal ITI Mathili,, failing which the bid shall be summarily rejected. The Bid EMD shall be returned to unsuccessful bidders on finalization of the Quotation. In the event of failure to execute necessary agreement with in the specific time the supply order or violation of terms and conditions by the successful Bidder, the E M D for the Schedule shall be forfeited. 6. Conditional Quotation shall be out rightly rejected. 7. The Quotations should be reach to the office of the Principal, Govt, I.T.I Mathili upto 04.06.2015 on 10.00 AM by speed post/ registered post or can be drop in the quotation box available in the Office only. No other mean of post will be allowed. The Quotations will be opened on 04.06.2015 at 10.30 AM in the Office of the Principal, Govt.I.T.I., Mathili in presence of the member of Purchase Committee and the Bidders or their authorized representatives who wish to be present. Quotation received after due date and time shall not be entertained and the authority shall not be held responsible for delay or missing of the Quotation during postal transit. If the office happens to be closed on the date of receipt and opening of this Quotation specified, the Quotation will be received & opened on the next working day at the same time and venue. 8. (I) The Price the rate quoted in words in the Quotation shall be taken into consideration quoted should be inclusive of all required accessories. (II)The Bidder shall have to give unit price rate including all charges (such as taxes, transportation, etc.). The Rate shall be indicated both in words and figures. In case of discrepancy, the rate quoted in words shall be taken into consideration. (III) No over & above the quoted/approved rate should be paid extra under any circumstances. 9. No claim shall be entertained towards any expenses made by the Bidders for submission of the Quotation in case of cancellation or withdrawal of Quotation call notice. 10. Delivery of mat eria ls mu st be accompanied with Manufacturing Test Certif icate /Guarantee Certificate/Manual/Leaflets, as applicable. 11. Unilateral stoppage of supply by the supplier without prior written permission shall be considered as breach of contract and the authority reserves the right to take action,as deemed fit. 12. Materials rejected by the authority shall be immediately removed with the knowledge of the undersigned. If it is not removed within the specified time, the authority reserves the right to remove the same and deduct the expenditure incurred from the supplier s bill.the authority shall in no way be held responsible for

any detoriation or damage to the materials under any circumstances what-so-over. 13. BID EVALUATION: - The Authority will evaluate and compare the Bids determined to be substantially responsive i.e. which are properly signed; and confirm to the terms and conditions, and specifications. The bid would be evaluated separately for each item: Quality, Price & Suitability for purpose of training to the ITI s trainees shall be a considering factor of selection of testing tools & equipments. The Bid shall also be evaluated taking into consideration of after sale service provided by the firm, experience in supply of similar type of Tools, Equipments and Machineries to reputed organization. Reputed Brand shall also be a considering factor for selection of the item. The authority is empowered to select any of the Quoted items taking in to account Quality & Price, which may not be lowest quoted price. 14. DELIVERY OF GOODS/CONSIGNEE: - The materials shall be delivered at Govt. ITI, Mathili, within 90 (Ninety) days from the date of issue of Purchase Order. Any delivery beyond the stipulated period shall attract a penalty of 0.5% per week of the contract amount subject to maximum of 10% of contract value. The goods on delivery will be physically verified by the Govt. ITI, Mathili through Technical Experts of the Institute and it shall be the responsibility of the suppliers to arrange demonstration on functioning of Individual goods/machines wherever required. 15. PAYMENT TERMS:- 100% payment w i l l be made (deducting penalty amount if any) within 7(Seven) days only after receipt of certificate in regards to satisfactory supply, installation, demonstration, smooth running/working, verification and stock entry of the goods within due date of delivery. 16. BID VALIDITY: The price quoted in the Bid should valid at least for 90 (Ninety) days from the date of opening of the Quotation. 17. WARENTEE/GUARENTEE: The goods shall be covered with warrantee/guarantee for minimum period of 12(Twelve) Months from the date of supply. The firm shall provide prompt after sales services and attend complaint within a week to prevent disruption of work in the Institute. 18.TAXES AND DUTIES: The Bidder shall be entirely responsible for all Taxes, Duties, License fees, Road permits etc. incurred until delivery of the contract goods to the consignee. 19. AUTHORIZATION: In case of Authorized supplier of the Manufacturer/Dealer the Bid must accompany with authorization from the Manufacturer/Dealer. 20. ACCEPTANCE: - The Bidder should sign each page of Bid document with seal as a token of acceptance of all terms and conditions of the Quotation and should submit along with the Bid documents. 21. PURCHASER S RIGHT: The Authority resolves the right to accept/reject any or all, full or part Bids without assigning any reason thereof. He may also withheld the payment on account of subsequently discovered evidence, nullify the whole or a part to the extent as may be necessary to protect himself from loss on account of : (i)defective supply not remedied. (ii)damaged caused due to departmental property. 22. BID LANGUAGE AND CURRENCIES; All information in the offer & all correspondences & documents, printed literatures furnished by the bidder should be written in English. The quoted price will be Indian Rupees only. 23. JURISDICTION OF THE COURT: The purchaser and the supplier shall agree that the competent court at Malkangiri shall have the jurisdiction to try and decide anything between the parties and they may approach the Competent Court at Malkangiri if required at any time. 24. AMENDMENT OF BIDDING DOCUMENTS: At any time prior to the deadline for submission of bids, the undersigned may, for any reason, whether at its own initiative or in response to a clarification requested by a prospective bidder, modify the bidding documents by amendment. Sd/- Principal Govt. ITI, Mathilil Dist- Malkangiri

PACKAGE-A SL Name of the Items with NO specification 1 Steel Rule 15 cm with metric graduation Brand Make Unit/Set Price Quoted rate in word 2 Try Square 10 cm blade. 3 Caliper inside 15 cm spring. 4 Caliper 15 cm hermaphrodite 5 Caliper outside 15 cm spring 6 Divider 15 cm spring 7 Straight Scriber 15 cm. 8 Centre Punch 10 cm 9 Screw driver 15 cm 10 Chisel cold flat 10 cm 11 Hammer ball peen 0.45 kg. With handle 12 Hammer ball peen 0.22 kg. With handle. 13 File flat 25 cm. second cut 14 File flat 25 cm. smooth 15 File half round second cut 15 cm. 16 Hacksaw frame fixed 30 cm. 17 Safety goggles. 18 Dot slot punch 10 cm. 19 Steel Rule 30 cm 20 Steel Rule 60 cm. 21 Straight edge 45 cm steel 22 Surface plate 45 x 45 cm CI / Granite. 23 Universal scribing block 22 cm.

24 V-Block pair 7 cm and 15 cm with clamps 25 Square adjustable 15 cm blade. 26 Angle plate 10 x 20 cm. 27 Spirit Level 15 cm metal 28 Punch letter 3 mm set. 29 Punch number set 3 mm. 30 Punch hollow 6 mm to 19 set of 5 31 Punch round 3mm x 4 mm set of 2 32 Portable hand drill (Electric) 0 to 6 mm 33 Drill twist straight shank 1.5 to 12 mm by 0.5 mm 34 Drill twist straight shank 8 mm to 15 mm by ½ mm 35 Taps and dies complete set in box B.A 36 Taps and dies complete set in box with-worth. 37 Taps and dies complete set in box 3-18 mm set of 10 38 File warding 15 cm smooth 39 File knife edge 15 cm smooth 40 File cut saw 15 cm smooth 41 File feather edge 15 cm smooth 42 File triangular 15 cm smooth 43 File round 20 cm second cut 44 File square 15 cm second cut 45 File square 25 cm second cut 46 Feeler gauge 10 blades

47 File triangular 20 cm second cut. 48 File flat 30 cm second cut. 49 File flat 20 cm bastard 50 File flat 30 cm bastard. 51 File Swiss type needle set of 12. 52 File half round 25 cm second cut. 53 File half round 25 cm bastard. 54 File round 30 cm bastard. 55 File hand 15 cm second cut. 56 Card file. 57 Oil Stone 15 cm x 5 cm x 2.5 cm 58 Stone carborandum 15 cm x 5 cm x 5 cm x 4 cm. 59 Oil Can 0.25 liters. 60 Pliers combination 15 cm 61 Soldering Iron 350 gm. 62 Blow Lamp 0.50 liters. 63 Spanner D.E. 6-26 mm set of 10 pcs. 64 Spanner adjustable 15 cm 65 Interchangeable ratchet socket set with a 12 mm driver, sized10-32 mm set of 18 socket & attachments. 66 Box spanner set 6-25 mm set of 8 with Tommy bar. 67 Glass magnifying 7 cm 68 Clamp toolmaker 5 cm and 7.5 cm set of 2. 69 Clamp C 5 cm 70 Clamp C 10 cm

71 Hand Reamer adjustable cover max 9,12,18mm set of 3 72 Hand Reamer taper 4-7 mm set of 4. 73 Reamer parallel 12-16mm set of 5. 74 Scraper flat 15 cm. 75 Scraper triangular 15 cm 76 Scraper half round 15cm 77 Chisel cold 9 mm cross cut 9 mm diamond. 78 Chisel cold 19 mm flat 79 Chisel cold 9 mm round noze. 80 Combination Set 30 cm. 81 Micrometer 0 25 mm outside. 82 Micrometer 25 50 mm outside. 83 Micrometer 50 75 mm outside. 84 Micrometer inside 25-50 mm with extension rods. 85 Vernier caliper 15 cm 86 Vernier height gauges 30 cm. 87 Vernier bevel protractor. 88 Screw pitch gauge. 89 Wire gauge, metric standard. 90 Drill chuck 12 mm. 91 Pipe wrench 40 cm 92 Pipe vice 100mm 93 Adjustable pipe tap set BSP with die set cover pipe size 15, 20, 25,32,38,50 mm. 94 Wheel dresser 95 Machine vice 10 cm.

96 Machine vice 15 cm 97 Sleeve drill Morse 0-1, 1-2, 2-3. 98 Vice bench 12 cm jaws. 99 Vice leg 10 cm jaw. 100 Machine vice 100mm. 101 Wing compass 25.4 cm or 30 cm. 102 Hand hammer 1 kg. with handle. 103 Hammer smith 2 kg. With handle. 104 Tongs roving 350mm. 105 Tongs fiat 350mm. 106 Smith's square 45 cm x 30 cm. 107 Cold set rodded 25X200mm. 108 Hot set rodded 25X200mm. 109 Swages top & bottom 12 mm /19 110 Swage block 35 x 35 x 12 cm. 111 Flatters (rodded) 55 mm square. 112 Fuller top & bottom 6 mm 9 mm (Pair). 113 Anvil 50 kg. 114 Trammer 30cm. 115 Pocker. 116 Hardle. 117 Leather apron. 118 Prick punch 119 Mallet. 120 Snips straight 25 cm. 121 Setting hammers with handle. 122 Planishing hammer.

123 Snip bent 25 cm. 124 Stake hatchet. 125 Stake grooving. 126 Slip Gauge as Johnson metric set. 127 Carbide Wear Block 1 mm 2 mm. 128 Gauge snap Go and Not Go 25 to 50 mm by 5mm. Set of 6 pcs. 129 Gauge plug single 3 ended 5 to 55 by 5 mm. Set of 11 pcs. 130 Gauge telescopic upto 150 mm. 131 Dial test indicator.01 mm on stand 132 Sine bar 125 mm. 133 Sine bar 250 mm. 134 Lathe tools H.S.S. tipped set. 135 Lathe tools bit 6 mm x 75 mm. 136 Lathe tools bit 8 mm x 75 mm. 137 Lathe tools bit 10 mm x 85mm. 138 Arm strong type tool bit holder R.H. 139 Arm strong type tool bit holder L.H. 140 Arm strong type tool bit holder straight. 141 Stilson wrenches 25 cm 142 Pipe cutter 6 mm to 50 mm wheel type. 143 Pipe bender spool type up to 25 mm. with stand manually operated. 144 Adjustable pipe chain tonge to take pipes up to 300 mm. 145 Adjustable spanner 38 cm long.

146 Dial vernier caliper 0 200 mm LCO 0.05 mm. (Universal type). 147 Screw thread micrometer with interchangeable 0-25mm. Pitch anvils for checking metric threads 60. 148 Depth micrometer 0-25 mm. 0.01 mm. 149 Vernier caliper 0-150 mm. L.C. 0.02 mm. 150 Comparators stand with dial indicator LC 0.01mm. 151 Engineer s try square (knifewedge) 150 mm blade. 152 Surface roughness comparison plates N1-N12 grade 153 Drilling machine pillar sensitive 0-20 mm cap with swivel table motorised with chuck & key. 154 Drilling machine bench sensitive 0-12 mm cap motorised with chuck and key. 155 Forge portable hand blower 38 cm to 45 cm. 156 Grinding machine (General purpose) D.E. pedestal with 2 cm. dia wheels rough and smooth with twist drill grinding attachment.

PACKAGE-B SL Name of the Items with NO specification 1 Steel Tape, 10 m length Brand Make Unit/Set Price Quoted rate in word 2 Plier Insulated, 150 mm 3 Plier Side Cutting, 150 mm 4 Screw Driver, 100 mm 5 Screw Driver, 150 mm 6 Electrician Connector, screw driver insulated handle thin stem, 100 mm 7 Heavy Duty Screw Driver, 200 mm 8 Electrician Screw Driver thin stem insulated handle, 250 mm 9 Punch Centre, 150 mm X 9 mm 10 Knife Double Bladed Electrician 11 Neon Tester 12 Steel Rule 300 mm 13 Hammer, cross peen with handle 14 Hammer, ball peen With handle 15 Gimlet 6 mm. 16 Bradawl 17 Scriber (Knurled centre position ) 18 Pincer 150 mm 19 C- Clamp 200 mm, 150 mm and 100 mm 20 Spanner Adjustable 150 mm, 15 degree 21 Blow lamp 0.5 ltr 22 Melting Pot 23 Ladel 24 Chisel Cold firmer 25 mm X 200 mm

25 Chisel 25 mm & 6 mm 26 Hand Drill Machine 0 to 6 mm capacity 27 Portable Electric Drill Machine 6 mm capacity 28 Pillar Electric Drill Machine 12 mm capacity 29 Allen Key 30 Oil Can 0.12 ltr 31 Grease Gun 32 Out Side Micrometer 0 to 25 mm 33 Motorised Bench Grinder 34 Rawl plug tool & bit 35 Pully Puller 36 Bearing Puller 37 Hygrometer 38 Thermometer 0 to 100 deg Centigrade 39 Scissors blade 150 mm 40 Crimping Tool 41 Wire stripper 20 cm 42 Chisel Cold flat 12 mm 43 Mallet hard wood 0.50 kg 44 Hammer Exeter type 0.40 kg 45 Hacksaw frame 200 mm 300 mm adjustable 46 Try Square 150 mm blade 47 Outside & Inside Divider Calliper 48 Pliers flat nose 150 mm 49 Pliers round nose 100 mm

50 Tweezers 100 mm 51 Snip Straight & Bent 150 mm 52 D.E. metric Spanner 53 Drill hand brace 0 to 100 mm 54 Drill S.S. Twist block 2 mm, 5 mm 6 mm set of 3 55 Plane, smoothing cutters 50 mm 56 Gauge, wire imperial 57 File flat 200 mm 2 nd cut 58 File half round 200 mm 2 nd cut 59 File round 200 mm 2 nd cut 60 File flat 150 mm rough 61 File flat 250 mm bastard 62 File flat 250 mm smooth 63 File Rasp, half round 200 mm bastard 64 Soldering Iron 25 watt, 65 watt, 125 wat 65 Copper bit soldering iron 0.25 kg. 66 Desoldering Gun 67 Hand Vice 50 mm jaw 68 Table Vice 100 mm jaw 69 Pipe Cutter to cut pipes upto 5 cm. dia 70 Pipe Cutter to cut pipes above 5 cm dia 71 Stock and Die set for 20 mm to 50 mm G. pipe 72 Ohm Meter; Series Type & Shunt Type 73 Stock and Dies conduit 74 Multi Meter (Analog) 0 to 1000 M Ohms, to 500 V 75 Digital Multi Meter

76 A.C. Voltmeter M.I. 0 500V A.C 77 Milli Voltmeter centre zero 100 0 100 volt 78 D.C. Milli ammeter 0-500m A 79 Ammeter MC 0-5 A, 0-25 A 80 A.C. Ammeter M.I.. 0-5A, 0-25 A 81 Kilo Wattmeter 0-1-3 kw 82 A.C. Energy Meter,Single phase 5 amp. Th Phase 15 amp 83 Power Factor Meter 84 Frequency Meter 85 Tachometer with watch 86 Current Transformer 87 Potential Transformer 88 Growler 89 Tong Tester / Clamp Meter 0 100 amp. 90 Megger 500 volts 91 Wheat Stone Bridge with galvanometer & battery 92 Contactor & auxiliary contacts 3phase, 440volt, 16amp 93 Contactor & auxiliary contacts 3 phase, volt, 32 amp. 94 Limit Switch 95 Rotary Switch 16 A 96 Load Bank5 KW( Lamp / heater Type) 97 Brake Test arrangement with two spring balance 0 to 25 kg rating 98 Knife Switch DPDT fitted with fuse termin 16 amp

99 Knife Switch TPDT fitted with fuse termin 16 amp 100 DC Power Supply 101 Inverter- 1 KVA with 12 V Battery Input- 12 volt DC, Output- 220 volt AC 102 Voltage Stabiliser Input: 150 230 volt AC Output: 220 volt AC 103 Rheostat 0-1 Ohm, 5 Amp 0-10 Ohm, 5 Amp 0-25 Ohm, 1 Amp 0-300 Ohm, 1 Amp 104 Domestic Appliances a. Electric Hot Plate 1500 watt b. Electric Kettle, 100 watts c. Electric Iron 1200 watts d. Immersion Heater 500/100/2000 watt e. A.C. Fan f. Geyser (Storage type) 15 ltr minimum g. Mixture & Grinder 105 Flux meter 106 Laboratory Type Induction Coil 107 3- point D.C. Starter 108 4- point D.C. Starter 109 Relays- a. Cut out

b. Reverse current c. Over current d. Over load e. Under voltage 110 Starters for 2 to 5 H.P. A.C Motors- a. Resistance type starter b. Direct on line Starter c. Star Delta Starter- manual, semi-autom and automatic d. Auto Transformer type 111 Used DC Generators-series, shunt and compound type for overhauling practice 112 D.C. Shunt Generator with control panel, 2.5 KW, 230 V 113 D.C. Compound Generator with control panel including fitted rheostat, voltmeter, ammeter and breaker, 2.5 KW, 230 V 114 DC Series Motor coupled with mechanical load 0.5 to 2 HP, 220 Volts 115 DC Shunt Motor2 to 3 HP, 220 volts 116 DC compound Motor with starter and switch2 to 3 HP, 220 volts 117 AC Squirrel Cage Motor with star delta starter and triple pole iron clad switch fuse.2 to 3 HP, 3-phase,400 volts, 50 cycles 118 AC phase-wound slip ring Motor with starter and switch5 HP, 400 volts, 3- phase,50 cycles 119 A.C. Series type Motor with mechanical load ¼ HP, 230V, 50 cycles 120 Single Phase Capacitor Motor with

starter switch 1 HP 230 volt 50 cycles 121 Universal Motor with starter/switch 230 volt, 50 cycles ¼ HP 122 Stepper Motor with Digital Controller 123 Shaded Pole Motor 124 Single phase Transformer, core type, air cooled 125 Three phase transformer, shell type oil cooled 126 Variable Auto Transformer 127 Oscilloscope Dual Trace,30 MHZ 128 Function Generator 129 Discrete Component Trainer 130 Linear I.C.Trainer 131 Digital I.C.Trainer 132 Bath Impregnating 133 Oven Stove 134 Oil Testing Kit 135 Battery Charger 136 Hydrometer 137 Air Breaker 5 KVA 138 Miniature Breaker 16 amp 139 Thyristor/IGBT controlled D.C. motor drive with tacho-generator feedback arrangement.1 HP 140 Thyristor/IGBT controlled A.C. motor drive with VVVF control 3 Phase, 2 HP

PACKAGE-C SL Name of the Items with NO specification 1 Allen Key set of 12 pieces (2mm to 14mm) 2 Caliper inside 15 cm Spring Brand Make Unit/Set Price Quoted rate in word 3 Calipers outside 15 cm spring 4 Center Punch 10 mm. Dia. x 100 mm. 5 Dividers 15 cm Spring 6 Electrician Screw Driver 250mm 7 Hammer ball peen 0.5 kg with handle 8 Hands file 20 cm. Second cut flat 9 Philips Screw Driver set of 5 pieces (100 mm to 300 mm) 10 Pliers combination 20 cm. 11 Screw driver 20cm.X 9mm. Blade 12 Screw driver 30 cm. X 9 mm. Blade 13 Scriber 15 cm 14 Spanner D.E. set of 12 pieces (6mm to 32mm) 15 Spanner, ring set of 12 metric sizes 6 to 32 mm. 16 Spanners socket with speed handle, T-bar, ratchet and universal upto 32 mm set of 28 pieces with box 17 Steel rule 30 cm inch and metric 18 Steel tool box with lock and key (folding type) 400x200x150 mm 19 Wire cutter and stripper 20 AC alternator slip ring puller 21 Adjustable spanner (pipe wrench 350 mm) 22 Air blow gun with standard accessories 23 Air Brake Assembly 24 Air impact wrench with standard accessories

25 Air ratchet with standard accessories 26 Allen Key set of 12 pieces (2mm to 14mm) 27 Alternator assembly used for LMV 28 Ammeter 300A/ 60A DC with external shunt 29 Angle plate adjustable 250x150x175 30 Angle plate size 200x100x200mm 31 Anti theft device 32 Anvil 50 Kgs with Stand 33 Auto Electrical test bench 34 Battery charger 35 Belt Tensioner gauge 36 Blow Lamp 1 litre 37 Caliper inside 15 cm Spring 38 Calipers outside 15 cm spring 39 Car Jet washer with standard accessories 40 Carburetor Solex, Mikuny for dismantling and assembling 41 Carburetor repair tool kit 42 Chain Pulley Block-3 ton capacity with tripod stand 43 Chisel 10 cm flat 44 Chisels cross cut 200 mm X 6mm 45 Circlip pliers Expanding and contracting type 15cm and 20cm each 46 Clamps C 100mm 47 Clamps C 150mm 48 Clamps C 200mm 49 Cleaning tray 45x30 cm. 50 Coil spring compressor for suspension spring 51 Compression testing gauge suitable for diesel Engine with standard accessories

52 Connecting rod alignment fixture 53 Constant Mesh Gear box with stand for Dismantling and assembly. 54 Copper bit soldering iron 0.25 Kg 55 Cut section Model of Mock layout of a motor car electrical system working model 56 Cut section models of shock absorbers 57 Cut section of cross ply and radial tyres 58 Cut section working model of automatic transmission Gear box 59 Cut section working model of centrifugal clutch assembly. 60 Cut section working model of Diaphragm clutch assembly. 61 Cut section working model of Single plate clutch assembly. 62 Cylinder bore gauge capacity 20 to 160 mm 63 Cylinder liner- Dry & wet liner, press fit & slidefit liner 64 DC Ohmmeter 0 to 300 Ohms, mid scales at 20 Ohms 65 Demonstration board of 2W Ignition system, ignition coil 66 Demonstration board of electronic Ignition system, ignition coil 67 Demonstration board of MPFI system 68 Depth micrometer 0-25mm 69 Dial gauge type 1 Gr. A (complete with clamping devices and with magnetic stand) 70 Different type of Engine Bearing model 71 Different type of piston model 72 Disk brake with caliper assembly 73 Distributor Duel advance type, reluctance type 74 Dividers 15 cm Spring 75 Drift Punch Copper 15 Cm 76 Drill point angle gauge

77 Drill twist 1.5 mm to 15 mm (various sizes) by 0.5 mm 78 Drum brake assembly 79 Electric Soldering Iron 230 V 60 watts 230 V 25 watts 80 Electric testing screw driver 81 Engineer s square 15 cm. Blade 82 Engineers stethoscope 83 Executive Auto Electrical tool kit 84 Feeler gauge 20 blades (metric) 85 File flat 20 cm bastard 86 File, half round 20 cm second cut 87 File, Square 20 cm second cut 88 File, Square 30 cm round 89 File, triangular 15 cm second cut 90 Files assorted sizes and types including safe edge file (20 Nos) 91 Flat File 25 cm second cut 92 Flat File 35 cm bastard 93 Front axle ( Rzeeppa Joint) with stand for Dismantling and assembly 94 Fuel feed pump for diesel 95 Fuel injection pump (Diesel) inline 96 Fuel injection pump dismantling tool kit /Universal Vice 97 Fuel injection pump, VE pump / Distributor fuel rotary pump (DPC) pumps / along with special tools and accessories. 98 Full floating axle and semi-floating axle assembly 99 Functional/experiment model of different type of sensors. 100 Garage stand 101 Gloves for Welding (Leather and Asbestos) 102 Glow plug tester 103 Granite surface plate 1600 x 1000 with stand and cover

104 Grease Gun 105 Grease Gun heavy duty trolley type 10 kg capciaty 106 Growler 107 Hacksaw frame adjustable 20-30 cm 108 Hammer Ball Peen 0.75 Kg 109 Hammer Chipping 0.25 Kg 110 Hammer copper 1 Kg with handle 111 Hammer Mallet 112 Hammer Plastic 113 Hand operated crimping tool (i) for crimping up to 4mm and (ii) for crimping up to 10mm 114 Hand reamers adjustable 10.5 to 11.25 mm, 11.25 to 12.75 mm, 12.75 to 14.25 mm and 14.25 to 15.75 mm 115 Hand Shear Universal 250mm 116 Hand vice 37 mm 117 Hollow Punch set of seven pieces 6mm to 15mm 118 Horn and Horn relay 119 Impact screw driver 120 Injector Multi hole type, Pintle type 121 Injector cleaning unit 122 Injector testing set (Hand tester) 123 Insulated Screw driver 20 cm x 9mm blade 124 Insulated Screw driver 30 cm x 9mm blade 125 Left cut snips 250mm 126 Lifting jack screw type 3 ton, 5ton & 20 Ton capacity 127 Magneto spanner set with 8 spanners 128 Magnifying glass 75mm 129 Marking out table 90X60X90 cm.

130 Multimeter digital 131 Multi-point fuel injection pump 132 Oil can 0.5/0.25 liter capacity 133 Oil pump for dismantling and assembling. 134 Oil Stone 15 cm x 5 cm x 2.5 cm 135 Oscilloscope 20MHz 136 Outside micrometer 0 to 25 mm 137 Outside micrometer 25 to 50 mm 138 Outside micrometer 50 to 75 mm 139 Outside micrometer 75 to 100 mm 140 Petrol nozzle 141 Philips Screw Driver set of 5 pieces (100 mm to 300 mm) 142 Pipe cutting tool 143 Pipe flaring tool 144 Piston ring compressor 145 Piston Ring expander and remover. 146 Piston Ring groove cleaner. 147 Pliers combination 20 cm. 148 Pliers flat nose 15 cm 149 Pliers round nose 15 cm 150 Pliers side cutting 15 cm 151 Portable electric drill Machine 152 Prick Punch 15 cm 153 Punch Letter 4mm (Number) 154 Radiator cut section-cross flow 155 Radiator cut section-down flow 156 Radiator pressure cap 157 Rear axle full floating type with stand for Dismantling and assembly

158 Right cut snips 250mm 159 Rivet sets snap and Dolly combined 3mm, 4mm, 6mm 160 Scraper flat 25 cm 161 Scraper half round 25 cm 162 Scraper Triangular 25 cm 163 Scriber 15 cm 164 Scriber with scribing black universal 165 Set of stock and dies Metric 166 Shear Tin Man s 450 mm x 600mm 167 Sheet Metal Gauge 168 Sher Tinmans 300mm 169 Soldering Copper Hatchet type 500gms 170 Solid Parallels in pairs (Different size) in Metric 171 Spanner Clyburn 15 cm 172 Spanner D.E. set of 12 pieces (6mm to 32mm) 173 Spanner T. flocks for screwing up and up-screwing inaccessible positions 174 Spanner, adjustable 15cm. 175 Spanner, ring set of 12 metric sizes 6 to 32 mm. 176 Spanners socket with speed handle, T-bar, ratchet and universal upto 32 mm set of 28 pieces with box 177 Spark lighter 178 Spark plug spanner 14mm x 18mm x Size 179 Starter motor axial type, preengagement type & Co-axial type 180 Steel measuring tape 10 meter in a case 181 Steel rule 15 cm inch and metric 182 Steel rule 30 cm inch and metric 183 Straight edge gauge 2 ft.

184 Straight edge gauge 4 ft. 185 Stud extractor set of 3 186 Stud remover with socket handle 187 Surface gauge with dial test indicator plunger type i.e. 0.01 mm 188 Synchronous Gear box with stand for Dismantling and assembly. 189 Tachometer (Counting type) 190 Tandem master cylinder with booster 191 Taps and Dies complete sets BSF 192 Taps and wrenches - metric 193 Telescope gauge 194 Temperature gauge with sensor 0-100 deg c 195 Tester sparking plug NEON Type 196 Thermostat 197 Thread pitch gauge metric, BSW 198 Timing lighter 199 Toe-in, toe-out gauge 200 Torque wrenches 5-35 Nm, 12-68 Nm & 50-225 Nm 201 Trammel 30 cm 202 Tread wear indicator 203 Tubed tyre of car, trucks & motorcycle 204 Tubeless tyre of cars & trucks 205 Tubeless tyre repair kit 206 Turbocharger cut sectional view 207 Tyre & split rim wheel assembly 208 Tyre pressure gauge with holding nipple 209 Universal puller for removing pulleys, bearings 210 V Block 75 x 38 mm pair with Clamps 211 Vacuum assisted hydraulics brake assembly with vacuum booster

212 Vacuum gauge to read 0 to 760 mm of Hg. 213 Valve Lifter 214 Valve spring compressor universal. 215 vernier caliper 0-300 mm with least count 0.02mm 216 Vice grip pliers 217 Water pump for dismantling and assembling 218 Wheel cylinder 219 Wiper motor assembly 220 Wire Gauge (metric) 221 Working Model of power windows 222 Working model of torque converter 223 4 Point relays 224 5 Point relays 225 Air bag simulator 226 Air conditioned CRDI Vehicle in running condition -LMV 227 Air conditioning service Unit (Car) 228 Air conditioning trainer kit 229 Arbor press hand operated 2 ton capacity 230 Automotive exhaust 5 gas analyzer (petrol & Diesel) or Diesel Smoke Meter 231 Bench lever shears 250mm Blade x 3mm Capacity 232 Diesel Engine CRDI - 4 stroke for Dismantling and assembling with swivelling stand 233 Diesel engine ( Running condition ) Stationary type 234 Discrete Component Trainer / Basic Electronics Trainer 235 Drilling machine bench to drill up to 12mm dia along with accessories 236 Dual Magnetization Yoke : AC / HWDC, 230 VAC, 50Hz

237 Four stroke petrol engine with CNG setup-working condition 238 Gas Welding Table 1220mm x760mm 239 Grinding machine (general purpose) D.E. pedestal with 300 mm dia wheels rough and smooth 240 Hand operated Hydraulic press 241 Heavy Commercial vehicle type (without body on frame) 242 Hydraulic jack HI-LIFT type -3 ton capacity, and 5 Ton capacity 243 Liquid penetrant Inspection kit 244 MPFI petrol engine with swiveling stand along with special tools for dismantling and assembling 245 Multi Scan Tool with oscilloscope 246 Petrol Engine(2-stroke) Motor Cycle/Scooter along with special tools and accessories 247 Pneumatic rivet gun with standard accessories 248 Spring tension tester 249 Tin smiths bench folder 600 x 1.6mm 250 Transfer case with stand for Dismantling and assembly. 252 Trolley type portable air compressor single cylinder with 45 liters capacity Air tank, along with accessories & with working pressure 6.5 kg/sq cm 252 Tube/ tyre vulcanizing machine 253 Two post car lift capacity 4000 kg 254 Tyer Changer Machine 255 Ultrasonic Injection cleaning equipment 256 Welding plant Oxy-Acetylene complete ( high pressure) 257 Welding Transformer ( 150-300 Amps) 258 Wheel alignment Machine computerized 3D 259 Wheel balancing machine

260 Working Condition of Diesel Engine CRDI - 4 stroke Engine Assembly with fault simulation board 261 Working Condition of Petrol MPFI Engine Assembly with fault simulation board Principal ITI Mathili

[Type text]