IL511001EN Brand Logo reversed black out of INS # RSA-MRZ Installation Instructions IMPORTANT: Read carefully before installing fixture. Retain for future reference. WARNING Risk of Electric Shock Disconnect power at fuse or circuit breaker before installing or servicing. WARNING Risk of Fire/Electric Shock. If not qualified, consult an electrician. WARNING Proper grounding is required to ensure personal safety. WARNING Risk of burn Use protective gear to ensure personal safety. This product must be installed in accordance with the applicable installation code by a certified electrician, familiar with the construction and operation of the product and hazard involved. To prevent possible wiring damage, do not expose wiring to edges of sheet metal or other sharp objects. Fixture in compliance with UL 1598 and UL 8750. MAX ambient temperature 25 C for all small fixtures. All electrical wire from junction box to fixture is to be provided by others. Ensure mounting surface s can support fixture assembly. Ensure all screws are torqued to proper settings. This product must be installed in accordance with applicable installation code and the hazards involved. Battery Section: This luminaire is provided with a factory installed emergency lighting pack and must be serviced by a person familiar operation of the product and the hazards involved. Danger Risk of shock. Disconnect all power and disable the battery pack Description: The RSA-MRZ is a single and multi-head, recessed group of products with integral LED dedicated head / heads. Options include: flanged or mud-in trim, varied LED color temperatures, lumen packages, CRI, paint finishes, and optics are available. Each fixture head / heads tilt 45 deg with 365 deg rotation. Accessories available include: different shielding media, Chicago plenum, and remote mounted battery pack. The RSA-MRZ also has two available controls platforms, LumaWatt Pro and WaveLinx.
INSTALLATION Flange Full Housing Assembly 1. Unpack RSA-MRZ fixture and ensure that all parts are included. (Figure 1) Figure 1. Accessory Plate (5) Wirenuts (2) S-Hooks Head Plate (2) 8-32 Screw (2) #1/4-20 Flange Nut Sheet Rock/ Grid Ceiling Tile Cut hole in ceiling or ceiling tile per cutout chart below: 1 Head Cut 1 Head (sensor) Cut 2 Head 2 Head (sensor) Length 5.63 5.88 7.03 7.28 10.91 11.16 12.31 12.56 Flange Length 6.67 7.97 11.95 13.25 Width 5.82 6.07 5.82 6.07 5.82 6.07 5.82 6.07 Cut 3 Head Cut 3 Head (sensor) Cut 4 Head Cut 4 Head (sensor) Length 16.16 16.41 17.56 17.81 21.41 21.66 22.81 Flange Length 17.20 18.50 22.45 23.75 Width 5.82 6.07 5.82 6.07 5.82 6.07 5.82 2 EATON RSA-MRZ Installation Instructions IL511001EN
Mounting with ¼-20 Threaded Rod (All Thread) Options for threaded rod: Unistrut, Hanger Bars, Metal Bar Hanger Space ¼-20 threaded rod to line up with the knockouts on top of the fixture housing per distance(s) provided below. 1 Head 2 Head 3 Head 4 Head 5 Head 6 Head Distance Between Holes 3.53 8.78 14.03 19.28 24.53 29.78 Distance Holes off Center 1.338 0 0 0 0 0 Distance From End 1.063 1.063 1.063 1.063 1.063 1.063 2. Remove Fixture Head Plate, Using the S hooks to support the Fixture Head Plate, and set the #8-32 screws aside to be used again. Disconnect low voltage Red and Blue wires at the WAGO connector junction located midway between the LED driver and fixture head mounting plate. (Figure 2) Figure 2. IL511001EN EATON RSA-MRZ Installation Instructions 3
3. Remove both ½ (0.5 ) knockouts from the top of the housing for threaded rod installation. (Figure 3) Figure 3. Remove knockouts for Threaded 4. Raise fixture housing into ceiling so the threaded rod feeds into the knockout holes. Make sure the flanges of the fixture housing are pulled tightly against the ceiling using the ¼-20 flange nuts on the threaded rod inside the housing. Figure 4. #1/4-20 Threaded Rod Attached to Structure #1/4-20 Flange Nut Lift fixture into place and fasten with #1/4-20 Flange Nut 4 EATON RSA-MRZ Installation Instructions IL511001EN
(Figure 4) Figure 5. Attach Whip to Accessory Plate 5. Power wires can be pulled through the power access plate. (Figure 5) Figure 6. Insert S-Hooks into rectangular slots IL511001EN EATON RSA-MRZ Installation Instructions 5
6. Use the S Hooks provided to attach through the rectangular slots on the non-power side of the housing. Figure 7. Hang Head Assembly From S-Hooks Connect Low Voltage wires Using Provided WAGO connectors (Figure 6) 7. Lift the Fixture Head Plate up to the S Hooks and attach through the slots on the small flanges. (Figure 7) Figure 8. Wiring Table: Black - Hot White - Neutral Green - Ground Purple - 0-10V (+) Gray - 0-10V (-) 6 EATON RSA-MRZ Installation Instructions IL511001EN
8a. Remove S Hooks while supporting Fixture Head Plate. Move the Fixture Head Plate into the housing, inserting the small flanges into the rectangular slots at a slight angle. Ensure wires do not get pinched along the edges of the plate and tilt up. Install the 8-32 screws. (Figure Figure 8A. Re-attach Head Plate using provided 8-32 thread forming screws 8. Reconnect the Red and Blue low voltage wires into the provided Wago connectors. Connect the hot, neutral, ground, purple (0-10V (+)), and gray (0-10V(-)) wires from fixture side to power feed side using wire nuts provided - minimize the lengths of wires being pushed back into the wire compartment, cut and strip wires to a Figure 9. #1/4-20 Threaded Rod Attached to Structure Structure (by others #1/4-20 Flange Nut Lift fixture into place and fasten with 1/4-20 Flange Nut Drywall Screws (by others) To finish - apply a generous amount of joint compound to fixture flange and feather at least 12 from fixture aperture. Mud in up to the trim around the edge of the fixture. IL511001EN EATON RSA-MRZ Installation Instructions 7
Replacing Optics shorter length if necessary. (Figure 8) Figure 10. Mud In/ Gypsum/ Sheet Rock Full Housing Assembly 9. Follow Flange Version above. Mounting shown below. (Figure 9) Figure 11. Head Assembly ML4 Optic Media (Optional) Snoot O-Ring (Remove only when using Shielding Media) Bezel Ring 8 EATON RSA-MRZ Installation Instructions IL511001EN
Head Rotation Figure 12. 360 Rotation pull down head to rotate up to 45 IL511001EN EATON RSA-MRZ Installation Instructions 9
Warranties and Limitation of Liability Please refer to www.eaton.com/lightingwarrantyterms for our terms and conditions. Garanties et limitation de responsabilité Veuillez consulter le site www.eaton.com/lightingwarrantyterms pour obtenir les conditions générales. Garantías y Limitación de Responsabilidad Visite www.eaton.com/lightingwarrantyterms para conocer nuestros términos y condiciones. Eaton 1121 Highway 74 South Peachtree City, GA 30269 P: 770-486-4800 www.eaton.com/lighting Canada Sales 5925 McLaughlin Road Mississauga, Ontario L5R 1B8 P: 905-501-3000 F: 905-501-3172 2017 Eaton All Rights Reserved Printed in USA Imprimé aux États-Unis Impreso en los EE. UU. Publication No. IL511001EN November 1, 2017 Eaton is a registered trademark. All trademarks are property of their respective owners. Eaton est une marque de commerce déposée. Toutes les autres marques de commerce sont la propriété de leur propriétaire respectif. Eaton es una marca comercial registrada. Todas las marcas comerciales son propiedad de sus respectivos propietarios. Product availability, specifications, and compliances are subject to change without notice La disponibilité du produit, les spécifications et les conformités peuvent être modifiées sans préavis La disponibilidad de productos, las especificaciones y los cumplimientos están sujetos a cambio sin previo aviso