INSTALLATION INSTRUCTIONS Accessory S P/N 08R04-TK6-100A Application 2012 FIT Publications No. AII 45990 Issue Date AUG 2011 PARTS LIST Door Visors cannot be installed on a vehicle equipped with the accessory B-pillar trim. 2 Brackets H Left front door visor 12 Clips Right front door visor EPT sealer 6 Sealers Left rear door visor TOOLS AND SUPPLIES REQUIRED Right rear door visor Isopropyl alcohol Shop towel Ruler Masking tape Illustration of the Door Visors installed on the vehicle RIGHT REAR 2 Brackets F RIGHT 8 Brackets G Q0D1420AH 2011 American Honda Motor Co., Inc. All Rights Reserved. AII 45990 (1108) 08R04-TK6-1A00-90 1 of 10
INSTALLATION NOTE: Visors may not be legal in all states. Please check the laws of your state. These installation instructions show the left door visors being installed. The same procedure applies to installing the right door visors. Do not damage the paint finish or the run channels when installing the door visors. Handle the door visors with care. They are not designed to absorb shock or impact. Thoroughly clean the surfaces where the door visors attach using a shop towel dampened with isopropyl alcohol. Let the cleaned surface dry thoroughly before installation. This door visor kit should be installed only if the ambient air temperature is 15 C (60 F) or above. Align and install the door visors carefully. Trying to detach and reattach the visor can damage the part and/or ruin the adhesive so it no longer sticks properly. To allow the adhesive to cure, do not wash the vehicle for 24 hours. Please advise your customer. Installing the Rear Door Visor 1. Fully open the left rear window. 2. Pull out the upper corner of the run channel. 3. Open the run channel as shown, and measure where the EPT sealer (long) will attach. 50 mm (2.0 in.) RUN CHANNEL JOIN EPT SEALER (long) JOIN SEALER ATTACHMENT POINT (Clean with EPT SEALER (long) 7 mm (0.3 in.) OUTSIDE OUTSIDE 861820AH 4. Using isopropyl alcohol, clean the area where the EPT sealer (long) will attach. 5. Remove an EPT sealer (long) from the adhesive backing, and attach it as shown. Make sure it is attached securely. 831101AH 2 of 10 AII 45990 (1108) 2011 American Honda Motor Co., Inc. All Rights Reserved.
6. Reinstall the run channel. Make sure it is installed correctly. 9. Using isopropyl alcohol, clean the area where the EPT sealer (short) will attach. EPT SEALER (short) Check the run channel installation. 831103BH 7. Slide the left rear quarter trim forward slightly to release the two retaining tabs. Do not try to remove the left rear quarter trim, the clip is easily damaged. EPT SEALER (short) REAR BOTTOM GROOVE SEALER ATTACHMENT POINT (Clean with isopropyl alcohol.) REAR OUTSIDE 7 mm (0.3 in.) OUTSIDE 861821AH 10. Remove an EPT sealer (short) from the adhesive backing, and attach it as shown. Make sure it is attached securely. RETAINING TABS QUARTER TRIM 831104AH 8. Pull out the rear corner of the run channel. 2011 American Honda Motor Co., Inc. All Rights Reserved. AII 45990 (1108) 3 of 10
11. Reinstall the run channel and left rear quarter trim. Make sure the run channel is installed properly. 12. Pull down the run channel in the areas shown. SASH VIEW VIEW 60 mm (2.4 in.) 60 mm (2.4 in.) 2 BRACKETS G SASH SASH Check the run channel installation. 831203BH 040502AJ 13. Install two brackets G to the door sash at the measurements shown. 14. Reinstall the run channel. Make sure the brackets G are installed correctly against the door sash as shown. 4 of 10 AII 45990 (1108) 2011 American Honda Motor Co., Inc. All Rights Reserved.
15. Using isopropyl alcohol, clean the door sash where the left rear door visor will attach. Clean with isopropyl alcohol. 17. Peel back the adhesive backing partway and attach it to the outer surface of the left rear door visor with masking tape. Remove two adhesive backings. MASKING TAPE 040503AJ 16. Remove the adhesive backing from two sealers, and attach them to the left rear door as shown. 7 mm (0.3 in.) Align. TRIM BACKINGS (Remove.) BACKING (Peel back.) 040505AJ 18. Secure the left rear door visor to two brackets G with two clips. NOTE: Align the brackets and the door visor carefully before installing the clips. The clips cannot be removed and reinstalled. SEALER TRIM Align. 5 mm (0.2 in.) 2 CLIPS 040506AJ SEALER 040504BJ 2011 American Honda Motor Co., Inc. All Rights Reserved. AII 45990 (1108) 5 of 10
19. Push the left rear door visor upward, and check that it aligns with the contour of the door sash. Push the brackets firmly against the door sash so there is no gap between the clips and the sash. 20. Insert a bracket H between the rear pillar trim and the door sash. Secure the left rear door visor to the bracket H with a clip. NOTE: The clip cannot be removed and reinstalled. SASH BRACKET H Push. SASH SASH BRACKET H REAR PILLAR TRIM CLIP 040507AJ 040508AJ 6 of 10 AII 45990 (1108) 2011 American Honda Motor Co., Inc. All Rights Reserved.
21. Remove the adhesive backing while pressing the left rear door visor in the direction of the arrow so there is no gap between the brackets and the door sash. Installing the Front Door Visor 23. Fully open the left front window. 24. Pull down the run channel in the areas shown. Space evenly. VIEW 60 mm (2.4 in.) VIEW 60 mm (2.4 in.) BACKING (Remove.) 2 BRACKETS G Press firmly. LEFT Push. 040509AJ 22. Press on the ends of the door visor for 30 seconds. 040510AJ 25. Install two brackets G to the door sash at the measurements shown. 26. Reinstall the run channel. Make sure the brackets G are installed correctly against the door sash as shown. 2011 American Honda Motor Co., Inc. All Rights Reserved. AII 45990 (1108) 7 of 10
27. Install a bracket F between the door sash and the run channel in the position shown. 29. Remove the adhesive backing from a sealer, and attach it to the left front door as shown. BRACKET F 3 mm (0.1 in.) Align. TRIM SEALER SASH 761015AS 28. Using isopropyl alcohol, clean the door sash where the left front door visor will attach. 040512BJ 30. Peel back the adhesive backing partway and attach it to the outer surface of the left front door visor with masking tape. Remove two adhesive backings. Clean with isopropyl alcohol. BACKING (Peel back.) BACKINGS (Remove.) MASKING TAPE 040511AJ 040513AJ 8 of 10 AII 45990 (1108) 2011 American Honda Motor Co., Inc. All Rights Reserved.
31. Secure the left front door visor to two brackets G with two clips. NOTE: Align the brackets and the door visor carefully before installing the clips. The clips cannot be removed and reinstalled. 32. Push the left front door visor upward, and check that it aligns with the contour of the door trim. Push the brackets firmly against the door sash so there is no gap between the clips and the sash. SASH Align. Push. TRIM 2 CLIPS 040514AJ Equal. LEFT REAR VISOR Align. 040515AJ 2011 American Honda Motor Co., Inc. All Rights Reserved. AII 45990 (1108) 9 of 10
33. Move bracket F up or down to align it with the clip installation hole in the left front door visor. 36. Press on the ends of the door visor for 30 seconds. 37. Repeat steps 1 thru 36 on the right side of the vehicle. CLIP CLIP BRACKET F 040516AJ 34. Secure the left front door visor to the bracket F with a clip. NOTE: The clip cannot be removed and reinstalled. 35. Remove the adhesive backing while pressing the left front door visor in the direction of the arrow so there is no gap between the brackets and the door sash. BACKING (Remove.) Press firmly. CONFIRMATION AFTER INSTALLATION 1. Start the engine. 2. Using the power window switch, fully close each window and check that there are no problems, such as a pinched run channel, etc. 3. Using the power window switch, repeat opening and closing of each window from fully closed to half-open 4 or 5 times to allow the run channels to fully seat. (While doing this, check for any problems with the window operation.) 4. Referring to the service manual for the vehicle, reset the power window control unit. (If the automatic closing/opening does not function after the reset, repeat the procedure.) NOTE: This reset must be done to ensure that the anti-pinching function works properly. USE AND CARE When the door visors are dusty, clean them with a soft cloth dampened with water. If the door visors are very dirty, clean them with a neutral detergent and water. Do not use any volatile solvents (e.g. thinner, benzine, alcohol, etc.) or a cleaner containing abrasive material. BRACKETS G Push. 040517AJ 10 of 10 AII 45990 (1108) 2011 American Honda Motor Co., Inc. All Rights Reserved.