Tap and Drill Bit Selection Guide

Similar documents
8 to 10 threads chamfered for easy thread starting in tough material.

TAPS & DIES S.T.I. TAPS - HIGH SPEED GROUND MACHINE SCREW SIZES FRACTIONAL SIZES

SPIRAL POINT TAPS for through hole tapping

ITM HSS GROUND THREAD HAND TAPS - MACHINE SCREW

Table of Contents. Standard Taps

Aluminium and (-2)* aluminium casting alloys *() * emulsion (long-chip) **

member sizes 0-6 have male point in addition to length shown in the general dimensions on page 162

CUTTING TOOLS 5/64 27/64 3/32 7/16 7/64 29/64 1/8 15/32 9/64 31/64 5/32 1/2 11/64 3/16 3/16 13/64 13/64 7/32 7/32 15/64 15/64 1/4 1/4 17/64 17/64 9/32

Table of Contents. Standard Taps

TAPS AND DIES. American Made American Owned

P&N/SUTTON. A trusted name, serving Canadian industries since

Bluechip Tooling td Tel Table of Content Type Page range Metric M with chamfer M3 - M20 M5 - M Metric

TPI NO. OF DIA. THREAD EDP NO. SIZE UNC UNF FLUTES LIMIT LENGTH OAL SETS TAPER PLUG BOTTOM

Introduction. Sparkplug / Plugsaver Kits

Taps, Dies & Threading

Mill - Thread Inserts and Kits

Solid Carbide Thread Milling

Scandinavian Tool Systems AB is a Swedish based manufacturer and supplier of tools for thread turning, thread milling, parting off and grooving.

LEADER CORPORATION CATALOG

POWER PRICE UNI. powerful UNF METAL. UNCPower. power ful GOLD FOR. powerful TOP GEOMETRIES UNF PERFECT CHOICE VER. perfect thread form.

Solid Carbide Thread Milling

Performance requires quality.

Hand Taps For Through or Blind Holes in General Machining Applications

CMT Vertical Mill-Thread

Metrics

Thread and Connector Identification

METAL DRILLING. Metal Drilling ENGINEERED FOR CONTROLLED PRECISION AND SPEED 118 SPLIT POINT 118 STANDARD POINT 135 SPLIT POINT TURBOMAX JET POINT

Edge Preparation. Edge Preparation. Centre Drills...5. Spot Drills (90 & 120 ) Flute Countersinks...8. Edge Preparation

SPRING LOADED DEVICES

121 indexable. Butt WelDeD tools. Die heads & chasers. restorers. Page Page sheet & tube Drills. Drills. Page Page...

$1795 $2350 $540 $1650 $2700 $1200 BONUS! BONUS! More than 3,000 tools within our range! 295PC TOOL KIT 262PC TOOL KIT 7 DRAWER ROLL CABINET

Lubrication Fittings. General Information. Alemite Lubrication Fittings include:

NEW PRODUCTS GUIDE EDITION Oil Filter Remover Set 21 Piece. Oil Filter Remover Set Truck 6 Piece

MEET OUR TEAM. North American Tool Corporation 215 Elmwood Avenue, PO Box 116, South Beloit, IL CURTIS LANSBERY PRESIDENT & CEO

Carbide Drills When productivity matters - Stub 1. to Long 1

NIAGARA CUTTER THREAD MILLING THREAD MILLS

9 Drawer Top Chest - PRO+ Series 42 x 19 x 23¹ ₂ Capacity: 10,841 cu. in. List $1, $866 95

Connecting Rods External Thread

How to Identify Fluid Ports and Connectors

PLAIN RING THREAD RING TRUNCATED SET PLUG TAPERLOCK THREAD PLUG TAPERLOCK PLAIN PLUG TAPER PIPE PLUG REVERSIBLE PLAIN PLUG REVERSIBLE THREAD PLUG

ThreadMill. For Thread Milling

YE-PT19 EUROPE. HSS-PM (Powder Metallurgy) TAPS Excellent Performance on Various Work Materials HEAD OFFICE

October & November 2017 Retail Specials Available From

No. of Holes. Drill Dia. (in.)

Tugger T-Bolts Coupling (Extension) Nuts Eye Bolts Metric Coupling (Ext.) Nuts Latch Swing Bolts Heavy Hex Nuts...

Engineering Data. Assembly Length. How to Determine Correct Assembly Length

2017 NORTH AMERICA TAPS EDITION

PRECISION THREADING TECHNOLOGY

How to Identify Fluid Ports and Connectors

Super. Line. 10th Edition SUPER PRICE SUPER QUALITY SUPER AVAILABILITY

Auto Feed Drills & Tappers. Comprehensive range Single spindle operations Multi-spindle processes. More Than Productivity

HSS ground for steel to 900 N/mm 2, aluminium alloys, brass, bronze. Use For producing screw through-holes DIN EN 20273,

Lubrication Fittings. 1/4"-28 Taper Thread Fittings

Auto Feed Drills & Tappers. Comprehensive range Single spindle operations Multi-spindle processes. More Than Productivity

THREADED INSERTS.

Drilling Solutions. Solid Carbide Tools. New Expanded Offering VALUE AT THE SPINDLE. High Performance

FLEXIBLE. EASY-TO-USE. DURABLE. BI-METAL HOLE SAWS

BASIC STANDARDS. Core holes for tapping screws and bolts with tapping screw thread DIN Simple, most common tapping thread-joints.

Fine Pitch Cobalt Roughers

Weighs only 58 pounds Built-in carrying handle Includes: 1 / 2" 1" die head Foot switch. Front and Rear Chucks Unique One Blade Reamer

Specifications R & RX Lanco

LSM SFM. METRIC SPECIFICATIONS and TECHNICAL INFORMATION

Lubrication Installation Components, Accessories & Fittings Table of Contents

(Click on the links below for the category contents) YONG. Custom Hex Plain Plug Gages.. Page 29. Custom Cylindrical Plain Ring Gages...

Standard programme. Multi-bladed reamers and counterboring tools. The tool specialists for the trade.

Solid Carbide Tools. Drilling Solutions. New Expanded Offering. ISO 9001 Certified

PINS & BUSHINGS METRIC

INDEX METRIC SOCKET SCREWS. Page CAP HEAD SCREWS TORQUE INFORMATION 3

80 PHONE SECTION 3 CUTTING ONSITE SUPPLY RENTAL & EQUIPMENT 1. PIPING 2. WORKSHOP MACHINERY SPECIALISED FORCE

DRILL INSERTS & HOLDERS

Industrial Tooling Corporation Ltd. Product Catalogue Issue 10

10,000 Series. Highlights C-6

Threading tools to JIS standard

Thread Milling AM-CAT-THREADMILL(GB)-07/08. Cutters, Inserts and Holders

TECHNICAL INFORMATION

A M Supply Co. Hand Tools Metal Cutting. Metal Cutting. Lenox Seamers. Snips. Milwaukee Snip Sets. Snips. Phone:(405) (800)

Tooling for Swiss Automatics

SECTION FIVE INDUSTRIAL LUBRICATIONFITTINGS

14 Piece 1/4" Dr. Standard

Product features. only RS. Application-specific features RS. Indication for the RS UNF. 400 C max. 200 C. Lifting points ready for bolting RS RM

Conversion Factors 1

Keyed Industrial Chucks Keyless Industrial Chucks Rubber-Flex Collet Chucks Arbors

STAR TOOL SUPPLY / GRAND TOOL SUPPLY

Content. SU series. SU series. SL series. ST series. ST series. PC series. PC series. SC series ZTD03/04/05 SPGT WCMX KONDA TOOLS.

HEX-CELLENT TOOLS! ALLEN KEYS FOR EVERY APPLICATION DESIGNED FOR THOSE HARD TO REACH AREAS A GREAT ACCESSORY FOR CORDLESS SCREWDRIVER OR DRILL!

Power TOOLS. Power Threading Machine / Model 535. Power Threading / Model Model 300 Compact Threading Machine

PINS & BUSHINGS METRIC

NOTES FOR PLUG 30% RINGS UPTO 24MM 40% RINGS ABOVE 24 MM 40% 8) FOR LEFT HAND GAUGES ADD TO BASIC LIST PRICE.

TECHNICAL INFORMATION

The HSS drill bit range

TWISTED B R U S H E S

Blank Size AEW BEW CEW DEW AA A B C D E AAL AL BL CL AE BE CE DE HA HB HC HD /4-20, 10-24, /4-20, 5/ /8-16 LA LB LC LD LE

Our History Index 1/4" -28 Tapered Thread Fittings 1/4" NPT Fittings

Accuracy Build Credibility

GRINDING WHEEL COMPONENTS PRODUCT GUIDE

HTR Precisions Cutting Tools is proud to offer you the complete range of cutting tools of superior quality according to international standards.

MECHANICAL OVERLOAD CLUTCHES SECTION CONTENTS

TOTEM HSS HAND / SHORT MACHINE / LONG SHANK MACHINE TAPS

List No STANDARD All sizes 1 each

TOOL SETS. Handsaws 1

Transcription:

148 2012/2013 Power Tools & Accessories Catalog Tap and Drill Bit Selection Guide American Standard and Unified Form Threads Tap drill size is approximately 7% of threaded depth. Thread Nominal Size Standard Drill Size Decimal 0 80 NF 3/64".0469" 1 64 NC 3.09" 1 72 NF 3.09" 2 6 NC 0.0700" 2 64 NF 0.0700" 3 48 NC 47.078" 3 6 NF 4.0820" 4 40 NC UNC 43.0890" 4 48 NF 42.093" 40 NC 38.101" 44 NF 37.1040" 6 32 NC UNC 36.106" 6 40 NF 33.1130" 8 32 NC UNC 29.1360" 8 36 NF 29.1360" 10 24 NC UNC 2.149" 10 32 NF UNF 21.190" 3/16 24 NS 26.1470" 3/16 32 NS 22.170" 12 24 NC 16.1770" 12 28 NF 14.1820" 14 20 NS 10.193" 1/4 20 NC UNC 7.2010" 1/4 28 NF UNF 3.2130" /16 18 NC UNC F.270" /16 24 NF UNF I.2720" 3/8 16 NC UNC /16".312" 3/8 24 NF UNF Q.3320" 7/16 14 NC UNC U.3680" 7/16 20 NF UNF 2/64".3906" 1/2 13 NC UNC 27/64".4219" 1/2 20 NF UNF 29/64".431" 9/16 12 NC UNC 31/64".4844" 9/16 18 NF UNF 33/64".16" /8 11 NC UNC 17/32".312" /8 18 NF UNF 37/64".781" 3/4 10 NC UNC 21/32".662" 3/4 16 NF UNF 11/16".687" 7/8 9 NC UNC 49/64".766" 7/8 14 NF UNF 13/16".812" 1 8 NC UNC 7/8".870" 1 14 NS 1/16".937" 1-1/8 7 NC UNC 63/64".9844" 1-1/8 12 NF UNF 1-3/64" 1.0469" 1-1/4 7 NCUNC 1-7/64" 1.1094" 1-1/4 12 NF UNF 1-11/64" 1.1719" 1-3/8 6 NC UNC 1-7/32" 1.2188" 1-3/8 12 NF UNF 1-19/64" 1.2969" 1-1/2 6 NC UNC 1-11/32" 1.3438" 1-1/2 12 NF UNF 1-27/64" 1.4219" 1-3/4 NC UNC 1-9/16" 1.62" 2 4-1/2 NC UNC 1-2/32" 1.7813" 2-1/4 4-1/2 NC-UNC 2-1/32" 2.0313" 2-1/2 4 NC UNC 2-1/4" 2.200" 2-3/4 4 NC UNC 2-1/2" 2.000" 3 4 NC UNC 2-3/4" 2.700" 3-1/4 4 NC UNC 3" 3.0000" 3-1/4 4 NC UNC 3-1/4" 3.200" 3-3/4 4 NC UNC 3-1/2" 3.000" 4 4 NC UNC 3-3/4" 3.700" Metric Threads French International Standard (D.I.N.) Tap Size Standard Drill Size Decimal 2..4 French /64".0781" 2.6.4 D.I.N. #4.0820" 3.0 D.I.N. #40.0980" 3.60 French #39.099" 3.7 Optional #43.8090" 3..60 French & D.I.N. #33.1130" 4.70 D.I.N. 1/8".120" 4.7 French 1/8".120" 4..7 French & D.I.N. #26.1470".7 Optional #19.1660".80 D.I.N. 11/64".1719".90 French #20.1610" 1.00 Optional /32".163"..7 Optional 3/16".187"..90 French & D.I.N. #14.1820" 6 1.00 French & D.I.N. 13/64".2031" 6 1.2 Optional 3/16".187" 7 1.00 French & D.I.N. 1/64".2344" 7 1.2 Optional #1.2280" 8 1.00 French J.2770" 8 1.2 D.I.N. 17/64".266" 9 1.00 French /16".312" 9 1.2 D.I.N. /16".312" 10 1.00 Optional 23/64".394" 10 1.2 Optional 11/32".3437" 10 1.0 French & D.I.N. 11/32".3437" 11 1.0 D.I.N. 3/8".370" 12 1.2 Optional 7/16".437" 12 1.0 French 13/32".4063" 12 1.7 D.I.N. 27/64".4219" 12 1.7 Optional 29/64".431" 13 1.0 Optional 29/64".431" 13 2.00 Optional 7/16".437" 14 1.2 Optional 33/64".16" 14 1.7 Optional 1/2".000" 14 2.00 French & D.I.N. 1/32".4687" 1 1.7 Optional 17/32".313" 1 2.00 Optional 33/64".16" 16 1.0 Optional 37/64".781" 16 2.00 French & D.I.N. 3/64".469" 17 2.00 Optional 19/32".937" 18 1.0 Optional 21/32".663" Taper Pipe For tapping without reaming Thread Drill Thread Drill Thread Drill 1/16" D 3/4" 9/64" 2-1/2" 2-/8" 1/8" R 1" 1-/32" 3" 3-1/4" 1/4" 7/16" 1-1/4" 1-1/2" 3-1/2" 3-3/34" 3/8" 37/64" 1-1/2" 1-47/64" 4" 4-1/4" 1/2" 4/64" 2" 2-7/32" Straight Pipe Thread Drill Thread Drill Thread Drill 1/16" 1/4" 1/2" 23/32" 1-1/2" 1-3/4" 1/8" 11/32" 3/4" 9/64" 2" 2-7/32" 1/4" 7/16" 1" 1-/32" 2-1/2" 2-21/32" 3/8" 37/64" 1-1/4" 1-1/2" For more details visit Boschtools.com

f f f f f 2012/2013 Power Tools & Accessories Catalog 149 Black Oxide Heat-treated carbon steel provides long life and clean, accurate threads Rolled threads provide more accuracy than machined threads Laser-etched marking ensures size identification won't wear off Black oxide coating provides corrosion resistance Product Info Tap Point Styles Taper Plug Bottoming Taper f f8 10 chamfered threads at the tip ideal for starting threads in tough materials f Longest chamfer of all three types f Commonly used in through holes and with materials where a guide is necessary f Requires less torque due to more working teeth Plug (most widely used) f fgeneral purpose tap, with 3 chamfered threads f Used when there is sufficient room on a blind hole and tapping to the bottom is not required Bottoming f fused after the threads have been started f 1 3 chamfered threads at the tip are enough to start the hole and taps all the way to the bottom Note: Tap and die size is indicated by two numbers. The first number represents the diameter of the screw or bolt. The second number represents threads per inch. The letters after the tap size indicate particular screw or bolt standard: NC = National Coarse NF = National Fine NS = National Special NEF = National Extra Fine NPT = National Pipe Taper BSP = British Standard Pipe D.I.N. = French International Standard Example: A 1/4-20 NC tap will cut 1/4" outside diameter with 20 threads per inch for a National Coarse-type screw. Toll free: 877-BOSCH-99

10 2012/2013 Power Tools & Accessories Catalog Black Oxide Plug Taps (Bulk) Size and Thread Standard 9397 4 40 NC #43 9406 6 32 NC #36 9409 8 32 NC #29 9412 10 24 NC #2 941 10 32 NF #21 9418 12 24 NC #16 9421 14 20 NS #10 9432 1/4 20 NC #7 943 1/4 28 NF #3 9438 /16 18 NC F 9441 /16 24 NF I 9444 3/8 16 NC /16 9447 3/8 24 NF Q 940 7/16 14 NC U 943 7/16 20 NF 2/64 946 1/2 13 NC 27/64 949 1/2 20 NF 29/64 9462 9/16 12 NC 31/64 1 1 946 9/16 18 NF 33/64 1 1 9468 /8 11 NC 17/32 1 1 9471 3/4 10 NC 21/32 1 1 9474 3/4 16 NF 11/16 1 1 9477 7/8 9 NC 49/64 1 1 9480 7/8 14 NF 13/16 1 1 9483 1 8 NC 7/8 1 1 96303 3mm.0 D.I.N. #40 96304 3mm.60 French #39 9630 4mm.70 D.I.N. 1/8 96306 4mm.7 French 1/8 96307 mm.80 D.I.N. 11/64 96308 mm.90 French #20 96309 6mm 1.00 French and D.I.N. 13/64 96310 7mm 1.00 French and D.I.N. 1/64 96311 8mm 1.2 D.I.N. 17/64 96314 10mm 1.2 Optional 11/32 9631 10mm 1.0 French and D.I.N. 11/32 96316 11mm 1.0 D.I.N. 3/8 96317 12mm 1.0 French 13/32 96318 12mm 1.7 D.I.N. 27/64 Black Oxide Taper Taps (Bulk) Size and Thread Standard 9399 4 40 NC #43 9408 6 32 NC #36 9411 8 32 NC #29 9414 10 24 NC #2 9417 10 32 NF #21 9420 12 24 NC #16 9424 14 20 NS #10 9434 1/4 20 NC #7 9437 1/4 28 NF #3 9440 /16 18 NC F 9443 /16 24 NF I 9446 3/8 16 NC /16 948 1/2 13 NC 27/64 9461 1/2 20 NF 29/64 For more details visit Boschtools.com

2012/2013 Power Tools & Accessories Catalog 11 Black Oxide Bottoming Taps (Bulk) Size and Thread Standard 9398 4 40 NC #43 1 9407 6 32 NC #36 9410 8 32 NC #29 9413 10 24 NC #2 9416 10 32 NF #21 9419 12 24 NC #16 9423 14 20 NS #10 9433 1/4 20 NC #7 9436 1/4 28 NF #3 9439 /16 18 NC F 9442 /16 24 NF I 944 3/8 16 NC /16 9448 3/8 24 NF Q 941 7/16 14 NC U 947 1/2 13 NC 27/64 9460 1/2 20 NF 29/64 1 Pipe Taps (Bulk) Size and Thread Standard 9492 1/8 27 NPT R 949 1/4 18 NPT 7/16 9498 3/8 18 NPT 37/64 B4404 1/2 14 NPT 4/64 1 1 B440 3/4 14 NPT 9/64 1 1 B4409 2 11 1/2 NPT 1 1 Black Oxide Pipe Dies (Bulk) Size and Thread Standard Width Across Flat 9739 1/8 27 NPT 1" 9738 1/4 18 NPT 1" 9740 1/4 18 NPT 1-7/16" 1 1 9722 3/8 18 NPT 1-7/8" 1 1 973 1/2 14 NPT 1-7/8" 1 1 96336 1/8 28 BSP 1" Toll free: 877-BOSCH-99

12 2012/2013 Power Tools & Accessories Catalog Black Oxide Hex Dies (Bulk) Size and Thread Width Across Flat Standard 9680 4 40 1" NC 9683 6 32 1" NC 9686 8 32 1" NC 9689 10 24 1" NC 9692 10 32 1" NF 969 12 24 1" NC 9709 1/4 20 1" NC 9712 1/4 28 1" NF 971 /16 18 1" NC 9718 /16 24 1" NF 9721 3/8 16 1" NC 9724 3/8 24 1" NF 9727 7/16 14 1" NC 9730 7/16 20 1" NF 9733 1/2 13 1" NC 9736 1/2 20 1" NF 9734 1/2 13 1-7/16" NC 1 1 B46022 9/16 12 1-7/16" NC 1 1 B46023 9/16 18 1-7/16" NF 1 1 B46024 /8 11 1-7/16" NC 1 1 B4602 /8 18 1-7/16" NF 1 1 B46026 3/4 10 1-7/16" NC 1 1 B46027 3/4 16 1-7/16" NF 1 1 B46028 7/8 9 1-13/16" NC 1 1 B46029 7/8 14 1-13/16" NF 1 1 B46030 1 8 1-13/16" NC 1 1 9772 1 12 1-7/8" NF 1 1 96320 3mm.0 1" 96321 3mm.60 1" 96322 4mm.70 1" 96323 4mm.7 1" 96324 mm.80 1" 9632 mm.90 1" 96326 6mm 1.00 1" 96327 7mm 1.00 1" 96328 8mm 1.2 1" 96330 9mm 1.2 1" 96331 10mm 1.2 1" 96332 10mm 1.0 1" 96333 11mm 1.0 1" 96334 12mm 1.0 1" 9633 12mm 1.7 1" Black Oxide Screw Extractors (Bulk) Size and Thread 978 #1 spiral flute /64 9788 #2 spiral flute 7/64 9791 #3 spiral flute /32 9794 #4 spiral flute 1/4 9797 # spiral flute 17/64 9800 #6 spiral flute 13/32 1 1 9803 #7 spiral flute 17/32 1 1 9806 #8 spiral flute 13/16 1 1 9809 #9 spiral flute 1-1/8 1 1 B46212 pc spiral flute (#1 #) (carded) 1 9786 #1 straight flute 1/8 9789 #2 straight flute 3/16 9792 #3 straight flute 1/64 979 #4 straight flute /16 9798 # straight flute 3/8 9801 #6 straight flute 1/32 1 1 9804 #7 straight flute 9/16 1 1 B4481 pc straight flute (#1 #) (carded) 1 For more details visit Boschtools.com

2012/2013 Power Tools & Accessories Catalog 13 Black Oxide Tap and Die Sets Black Oxide 12 pc Tap Set B44711 Black Oxide 40 pc Tap and Die Set B44717 Black Oxide 8 pc Tap and Die Set B44713 # of Pieces Includes Case Type B46212 Spiral flute screw extractors (carded): (1) #1, (1) #2, (1) #3, (1) #4, (1) # 1 Card B4481 Straight flute screw extractors (carded): (1) #1, (1) #2, (1) #3, (1) #4, (1) # 1 Card B4621 12 Spiral extractors: #1 #6; drill bits: (1) /64", (1) 7/64", (1) /32", (1) 1/4", (1) 17/64", (1) 13/32" B44710 11 Taps: (1) 6-32, (1) 8-32, (1) 10-24, (1) 10 32, (1) 1/4 20; drill bits: (1) #36, (1) #29, (1) #2, (1) #21, (1) #7; (1) T-handle wrench # of Pieces Includes (taps) Includes (dies) B44711 12 Plug taps: (1) 6 32, (1) 8 32, (1) 10 24, (1) 10 32, (1) 12 24, (1) 1/4 20, (1) 1/4 28, (1) /16 18, (1) 3/8 16, (1) 7/16 14, (1) 1/2 13, (1) 1/8 27 B44712 19 Plug taps: (1) 10 24, (1) 6 32, (1) 8 32, (1) 10 32, (1) 1/4 20, (1) 1/4 28, (1) /16 18, (1) /16 24, (1) 3/8 16, (1) 3/8 24 B44713 8 Plug taps: (1) 6 32, (1) 8 32, (1) 10 24, (1) 10 32, (1) 12 24, (1) 1/4 20, (1) 1/4 28, (1) /16 18, (1) /16 24, (1) 3/8 16, (1) 3/8 24, (1) 7/16 14, (1) 7/16 20, (1) 1/2 13, (1) 1/2 20, (1) 9/16 12, (1) 9/16 18, (1) /8 11, (1) /8 18, (1) 3/4 10, (1) 3/4 16, (1) 1/8 27, (1) 1/4 18 B44714 19 Plug taps: (1) 3mm 0.60, (1) 4mm 0.70, (1) 4mm 0.7, (1) mm 0.80, (1) 6mm 1.00, (1) 7mm 1.00, (1) 8mm 1.2, (1) 9mm 1.2, (1) 10mm 1.2, (1) 10mm 1.0 B44716 77 Plug taps: (1) 4 40, (1) 6 32, (1) 8 32, (1) 10 24, (1) 10 32, (1) 12 24, (1) 1/4 20, (1) 1/4 28, (1) /16 18, (1) /16 24, (1) 3/8 16, (1) 3/8 24, (1) 7/16 14, (1) 7/16 20, (1) 1/2 13, (1) 1/2 20, (1) 9/16 12, (1) 9/16 18, (1) /8 11, (1) /8 18, (1) 3/4 10, (1) 3/4 16, (1) 7/8 9, (1) 7/8 14, (1) 1 8, (1) 1 12; pipe taps: (1) 1/8 27, (1) 1/4 18, (1) 3/8 18, (1) 1/2 14 B44717 40 Plug taps: (1) 4 40, (1) 6 32, (1) 8 32, (1) 10 24, (1) 10 32, (1) 12 24, (1) 1/4 20, (1) 1/4 28, (1) /16 18, (1) /16 24, (1) 3/8 16, (1) 3/8 24, (1) 7/16 14, (1) 7/16 20, (1) 1/2 13, (1) 1/2 20; pipe tap: (1) 1/8 27 B44718 40 Plug taps: (1) 3mm.0, (1) 3mm 0.60, (1) 4mm 0.70, (1) 4mm 0.7, (1) mm 0.80, (1) mm 0.90, (1) 6mm 1.00, (1) 7mm 1.00, (1) 8mm 1.2, (1) 9mm 1.00, (1) 9mm 1.2, (1) 10mm 1.2, (1) 10mm 1.0, (1) 11mm 1.0, (1) 12mm 1.0, (1) 12mm 1.7; BSP pipe tap: (1) 1/8 28 Includes (handle and accessories) 1 Brute Tough 1 Brute Tough Case Type 1 Brute Tough 1" hex dies: (1) #60, (1) 1/4 20, (1) 1/4 28, (1) /16 18, (1) /16 24, (1) 3/8 16, (1) 3/8 24 1" hex dies: (1) 6 32, (1) 8 32, (1) 10 24, (1) 10 32, (1) 12 24, (1) 1/4 20, (1) 1/4 28, (1) /16 18, (1) /16 24, (1) 3/8 16, (1) 3/8 24, (1) 7/16 14, (1) 7/16 20, (1) 1/2 13, (1) 1/2 20, (1) 1/8 27; pipe die: (1) 1/4 18; 1 7/16" hex dies: (1) 9/16 12, (1) 9/16 18, (1) /8 11, (1) /8 18, (1) 3/4 10, (1) 3/4 16 (1) 1" 6mm 1.00, (1) 1" 7mm 1.00, (1) 1" 8mm 1.2, (1) 1" 9mm 1.2, (1) 1" 10mm 1.2, (1) 1" 10mm 1.0 1" hex dies: (1) 4 40, (1) 6 32, (1) 8 32, (1) 10 24, (1) 10 32, (1) 12 24, (1) 1/4 20, (1) 1/4 28, (1) /16 18, (1) /16 24, (1) 3/8 16, (1) 3/8 24, (1) 7/16 14, (1) 7/16 20, (1) 1/2 13, (1) 1/2 20; 1 7/16" hex dies: (1) 1/4 18, (1) 1/2 13, (1) 1/2 20, (1) 9/16 12, (1) 9/16 18, (1) /8 11, (1) /8 18, (1) 3/4 10, (1) 3/4 16; 1 7/8" hex dies: (1) 7/8 9; (1) 7/8 14; (1) 1 8; (1) 1 12; 1 7/8" pipe dies: (1) 3/8 18, (1) 1/2 14 1" hex dies: (1) 4 40, (1) 6 32, (1) 8 32, (1) 10 24, (1) 10 32, (1) 12 24, (1) 1/4 20, (1) 1/4 28, (1) /16 18, (1) /16 24, (1) 3/8 16, (1) 3/8 24, (1) 7/16 14, (1) 7/16 20, (1) 1/2 13, (1) 1/2 20; pipe die: (1) 1" 1/8 27 1" hex dies: (1) 3mm.0, (1) 3mm.60, (1) 4mm.70, (1) 4mm.7, (1) mm.80, (1) mm.90, (1) 6mm 1.00, (1) 7mm 1.00, (1) 8mm 1.2, (1) 9mm 1.00, (1) 9mm 1.2, (1) 10mm 1.2, (1) 10mm 1.0, (1) 11mm 1.0, (1) 12mm 1.0, (1) 12mm 1.7, (1) 1/8 28 BSP (1) tap adapter, (1) T-handle wrench Spiral screw extractors #1, (1) tap wrench 1/4 1/2, (1) tap wrench 1/2 3/4, (1) T-handle wrench, (1) 1 7/16" hex die stock, (1) # screwdrivier, (1) screw pitch gauge (1) die stock/tap adapter, (1) T-handle wrench Spiral screw extractors #1 7, (1) # screwdriver, (1) tap wrench 1/4 1/2, (1) screw pitch gauge, (1) 1 7/16" hex die stock, (1) 1 7/8" hex die stock, (1) T-handle wrench 0 1/4, (1) T-handle wrench 1/4 1/2, (1) tap and die chart (1) # screwdriver, (1) screw pitch gauge, (1) T-handle wrench 0 1/4, (1) T-handle wrench 1/4 1/2, (1) tap wrench 1/4 1/2 (1) # screwdriver, (1) screw pitch gauge, (1) T-handle wrench 0 1/4, (1) T-handle wrench 1/4 1/2, (1) tap wrench 1/4 1/2 Toll free: 877-BOSCH-99

14 2012/2013 Power Tools & Accessories Catalog Tap and Die Accessories (Bulk) Description 39908 3/8" square drive T-handle tap wrench 1 9893 Tap and reamer wrench, 1/4 3/4" 1 B44719 Tap and reamer wrench, 1/2 1-1/8" 1 1 989 Tap and reamer wrench, 0 1/2" 1 9930 Die stock, solid, 1" 1 9934 Die stock adj., 1-7/16" hex dies 1 991 Screw pitch gauge, US thread, 10 40" 1 992 Screw pitch gauge, metric 1 High-Speed Steel Plug Taps and Hex Dies High-Speed Steel Plug Taps f f Abrasion and heat resistant for longer life fprovides f accuracy for tighter tolerances High-Speed Steel Hex Dies f f Abrasion and heat resistant for longer life fprovides f accuracy for tighter tolerances Size and Thread Corresponding Drill Size # Pieces/ Standard Pack 396400 4 40 NC #43 1 396401 6 32 NC #36 1 396402 8 32 NC #29 1 396403 10 24 NC #2 1 396404 10 32 NF #21 1 39640 12 24 NC #16 1 396410 1/4 20 NC #7 1 396411 1/4 28 NF #3 1 396412 /16 18 NC F 1 396413 /16 24 NF I 1 396414 3/8 16 NC /16" 1 39641 3/8 24 NF Q 1 396416 7/16 14 NC U 1 396417 7/16 20 NF 2/64" 1 396418 1/2 13 NC 27/64" 1 396419 1/2 20 NF 29/64" 1 396420 9/16 12 NC 31/64" 1 396421 9/16 18 NF 33/64" 1 396422 /8 11 NC 17/32" 1 396423 /8 18 NF 37/64" 1 396424 3/4 10 NC 21/32" 1 39642 3/4 16 NF 11/16" 1 396430 1/8 27 NPT 396431 1/4 18 NPT Multiples of Size and Thread Width Across Flat # Pieces/ Standard Pack 39640 4 40 1" NC 1 39641 6 32 1" NC 1 39642 8 32 1" NC 1 39643 10 24 1" NC 1 39644 10 32 1" NF 1 3964 12 24 1" NC 1 39648 1/8 27 1" NPT 1 396460 1/4 20 1" NC 1 396461 1/4 28 1" NF 1 396462 /16 18 1" NC 1 396463 /16 24 1" NF 1 396464 3/8 16 1" NC 1 39646 3/8 24 1" NF 1 396466 7/16 14 1" NC 1 396467 7/16 20 1" NF 1 396468 1/2 13 1" NC 1 396469 1/2 20 1" NF 1 39649 1/4 18 1-7/16" NF 1 396470 9/16 12 1-7/16" NC 1 1 396471 9/16 18 1-7/16" NF 1 1 396472 /8 11 1-7/16" NC 1 1 396473 /8 18 1-7/16" NF 1 1 396474 3/4 10 1-7/16" NC 1 1 39647 3/4 16 1-7/16" NF 1 1 396478 1/2 13 1-7/16" NC 1 1 396479 1/2 20 1-7/16" NF 1 1 For more details visit Boschtools.com

2024 © autodocbox.com Privacy Policy | Terms of Service | Feedback