EN-XX Retrofitting instructions Lighting NA_Deckblatt_9753.85.300.0_EN
SAFETY NOTES Professional Qualification These assembly instructions are aimed exclusively at skilled staff trained for this work. Intended Use Intended use is described in the machine s Operating Instructions. The attachment or installation of additional equipment does not constitute a change to the machine s intended use. Prior to Starting Assembly Work Park the machine on firm level ground, switch off the tractor s engine, apply the hand brake, remove the ignition key and keep safe. Allow the machine to come to a complete stop (rotating parts may carry on turning for a longish period). Secure machine and tractor against accidental rolling. Secure work area so that there can be no risk to or for other people. Observe the statutory regulations on accident prevention. Observe warning signs (pictograms) on the machine. - 2 -
SAFETY NOTES General Safety Notes for Assembly DANGER Risk of severe or life-threatening injuries all over the body due to getting caught up, being pulled in, crushing and hydraulic oil escaping at high pressure! It is imperative to follow the safety notes! Only couple and uncouple the machine on solid level ground, secure against accidental rolling and falling over. Only carry out work if the PTO drive shaft and the motor have been switched off, the handbrake has been applied and the ignition key has been removed and kept safe. Wait until all rotating machine parts come to a complete stop! Wear close-fitting workwear and use personal protective equipment such as safety glasses, gloves, safety shoes and safety helmet! Only raise the machine using lifting gear suitable for the purpose (hydraulic jack, crane, etc.) and only support it using appropriate supporting elements. No welding, cutting, grinding, drilling on frame, axles or other load-bearing parts. Check nuts and bolts for tight fit. Hoses and cables may not strain, rub or become trapped. Attachment or installation of non-standard equipment alters the overall weight and depending on the non-standard equipment involved may also alter the external dimensions of the machine. Pay attention to the altered dimensions in operation and particularly when driving on public roads. Attach sufficient ballast weights to the tractor. At least 20% of the vehicle s unladen weight on the front axle. Insufficient ballast will make tractor and machine uncontrollable when driving. Do not step between tractor and machine whilst attaching/coupling up. Have someone guide you in if the coupling point cannot be seen from the driver s seat of the tractor. Do not step between tractor and machine until both have come to a stop and have been secured against accidental rolling. Bring the supporting devices (e.g. support legs) into the correct position in each case. Secure as prescribed! Do not get close to hydraulic oil escaping under high pressure. Prior to Starting Up Follow the machine s Operating Instructions. Check safety equipment for completeness and function. Check oil levels. Check machine for compressed air and oil losses. Check tyre pressures and wheelnuts for tight fit. Check electrical, pneumatic and hydraulic connections to the tractor. Check service brake and parking brake for proper function. Completely release machine s parking brake and turn the crank handle inwards. Place tractor s hydraulic control unit in neutral position prior to attaching the machine. Pay attention to lateral locking of the tractor s three-point linkage depending on the machine type. - 3 -
MOUNTING INSTRUCTIONS 9753.85.300.0-4 -
PNR TEILE-NR MENGE BENENNUNG DESIGNATION DESCRIPTION BEMERK/REMARQUE FU ============================================================================================================================================= 0.01 00 9753.85.300.0 1 BELEUCHTUNG ECLAIRAGE LIGHTING SET 1 00 2441.22.011.0 4 VERSTEIFUNG RENFORCEMENT REINFORCEMENT 2 00 3846.75.023.0 1 DISTANZLASCHE ECLISSE ENTRETOISE SPACER TIEPLATE 3 00 3846.75.030.0 1 BOLZEN SZ. AXE PIN 4 00 9753.85.210.0 1 STREBE LI SZ JAMBE DE FORCE STRUT L 5 00 9753.85.220.0 1 STREBE RE SZ JAMBE DE FORCE STRUT R 6 00 9753.85.315.0 1 KLEMMSCHALE ENVELOPPE PEEL 7 00 9753.85.360.0 1 BELEUCHTUNGSHALTER SZ. SUPPORT SUPPORT 8 00 9753.85.370.0 1 FORMROHR TUBE FACONNE SZ SUPPORT SZ 9 00 9753.85.371.0 1 WINKEL CORNIERE ANGLE 10 00 9753.85.375.0 2 BOLZEN AXE PIN 11 00 9753.85.380.0 1 STREBE SZ. BRAS DROIT STRUT 12 00 9753.85.385.0 1 WINKEL CORNIERE ANGLE 13 00 101.839 12 SK-SCHR. M8X20-8.8-DIN 69 VIS M8X20 SCREW M8X20 14 00 103.087 1 SK-SCHRAUBE M12X35-DIN 933-8.8 VIS SCREW 15 00 103.287 4 SK-SCHR. M8X60 DIN 931-8.8 VIS M8X60 SCREW M8X60 16 00 103.304 4 SK-SCHR. M10X65 DIN 931-8.8 VIS M10X65 SCREW M10X65 17 00 103.326 2 SK-SCHR. M 12X70 DIN 931 VIS M 12X70 SCREW M 12X70 18 00 103.330 2 SK-SCHR. M12X90 DIN 931-8.8 VIS M12X90 SCREW M12X90 19 00 103.335 1 SK-SCHR. M 12X130 DIN 931-8.8 VIS HEXAGONAL SCREW, HEX.HD. 20 00 103.365 4 SK-SCHR. M16X55 DIN 931 8.8 ZN VIS M16X55 SCREW M16X55 21 00 122.107 4 SI-MUTTER M10 DIN 980-8 ECROU M10 DIN 980 NUT M10 DIN 980 22 00 122.108 2 SI-MUTTER M12 DIN 980-8 ZN ECROU M12 DIN 980-8 NUT M12 DIN 980-8 23 00 122.108 3 SI-MUTTER M12 DIN 980-8 ZN ECROU M12 DIN 980-8 NUT M12 DIN 980-8 24 00 122.110 4 SI-MUTTER M16 DIN 980-8 ZN ECROU M16 DIN 980 NUT M16 DIN 980 25 00 122.317 16 FLANSCHMUTTER M8 ECROU M8 NUT M8 26 00 157.829 4 SICHERUNGSRING 45X2,5 DIN 471 SEGMENT D ARRET CIRCLIP 27 00 162.402 8 SCHEIBE 24X8,5X1,5 RONDELLE WASHER 28 00 162.404 8 SCHEIBE 20X10,5X1,5 ZN RONDELLE WASHER 29 00 162.416 6 SCHEIBE 13*2 RONDELLE WASHER 30 00 163.111 4 SCHEIBE 60X45.2X2 RONDELLE WASHER 31 00 417.626 2 VIERKANTSTOPFEN COUVERCLE CARRE FITTING 32 00 438.016 1 KLAPPVORSTECKER 5X32 DIN 11023 GOUPILLE FENDUE PIN LINCH 33 00 459.112 2 KABELTUELLE 50/31/40/10/20 PASSE-FIL CABLE GROMMET 34 00 470.037 2 WARNTAFELN WS/RO PANNEAU D AVERTISS. WARNING PLATE 35 00 470.040 2 WARNTAFEL 423X283 PANNEAU AVERTISS. WARNING PLATE 36 00 470.053 2 RUECKLEUCHTE FEU ARRIERE P.TYPE E REAR LIGHT F.E-TYPE 37 00 470.960 2 RUECKSTRAHLER 55 ORANGE CATAPHOTE 55 REFLECTOR 55 38 00 475.173 14 KABELBINDER PLT 5 H 8,9X 450 ATTACHE-CABLE STRIP 39 00 476.237 1 VERSORGUNGSKABEL ZUS. L=7500MM CABLE L=7500MM CABLE L=7500MM 42 00 3846.75.020.0 2 TRAEGER SUPPORT TRANSPORT BRACKET 9755/BT 0261-5 -
Assembly Sequence 7 3 2 5 4 6 1-6 -
24 20-7 -
- 8 -
24 20-9 -
- 10 -
- 11 -
17 22 22-12 -
2x - 13 -
26 30 26 10 30 26 30 10 Lightly grease bearing points with universal grease! - 14 -
- 15 -
- 16 -
- 17 -
22 29 19 29-18 -
- 19 -
- 20 -
9 27 16-21 -
21 28 4x - 22 -
- 23 -
Laying lighting cable Feed lighting cable through from front to back. Secure lighting cable with accompanying cable ties. Feed cable with yellow plug through to the left. Feed cable with green plug through to the right. - 24 -
PÖTTINGER Service Support Centres Austria PÖTTINGER Landtechnik GmbH Industriegelände 1 4710 Grieskirchen Phone +43 7248 600-0 Fax +43 7248 600-2513 info@poettinger.at Deutschland PÖTTINGER Deutschland GmbH Landsberg Service Centre Spöttinger Straße 24 86899 Landsberg am Lech Phone +49 8191 9299-0 Fax +49 8191 59656 info@poettinger.at PÖTTINGER Deutschland GmbH Recke Sales and Service Centre Steinbecker Straße 15 49509 Recke Phone +49 5453 9114-0 Fax +49 5453 9114-14 France PÖTTINGER France S.a.r.l. La Chapelle 129b 68650 Le Bonhomme Phone +33 389 472830 Fax +33 389 472839 france@poettinger.at Italia POETTINGER Italia s.r.l. Via E. Fermi 6 29010 San Pietro in Cerro/PC Phone +39 0523 838012 Fax +39 0523 838253
Polska PÖTTINGER Polska Poladowo 70 64-030 Smigiel United Kingdom Alois POTTINGER UK Ltd. St. Marks Road 15 NN18AN Corby Phone +44 1536 272220 Fax +44 1536 206220 info.uk@pottingeruk.co.uk Ireland POETTINGER Ireland Ltd. Cashel road, Clonmel Co. Tipperary Phone +353 52 6125766 Україна PÖTTINGER Ukraine Prywokzalna vulitsa 50, Office 215 08300 Boryspil Phone +38 04595 710 42 Россия OOO "POETTINGER" Bachruschin Str. 32/1 115054 Moskau Phone +7 495 646 89 15 Fax +7 495 646 89 16 info.ru@poettinger.ru Canada POETTINGER Canada Inc. 650 Route 112 J0L 1T0 St. Cesaire Phone +1 450 469 5594 Fax +1 866 417 1683
United States POETTINGER US, Inc. 393 Pilot drive 46383 Valparaiso/IN Phone +1 219 510 5534 Fax +1 219 707 5412 POETTINGER US, Inc. West Iona Ave 93245 Lemoore/CA Australia POETTINGER Australia PTY LTD 15 Fordson Street Campbellfield/VIC 3061 Phone +61 3 9359 2969
PÖTTINGER Service Partner A worldwide network of well established Service Specialist Centres is at your disposal. This regional proximity guarantees the prompt supply of spare parts, enables optimum product handover and parameterisation of machines through competent personnel. Our service features include: Expertise through the regular training of professional personnel. 24 hour online ordering service for ORIGINAL INSIDE replacement parts. Long-term availability of replacement parts. And much more Contact your nearest Specialist Service Centre for more information, or go to www.poettinger.at