INDUSTRIAL VALVES. 2-Way Valves. ANSI Flanged Valves. Flush Tank Valves. Angle Stem Flush Tank. 3-Way Diverter Valves. 3, 4, & 5-Way Valves

INDUSTRIAL VALVS S SRIS AN SRIS F SRIS AF SRIS D SRIS M SRIS TI SRIS IM SRIS FF SRIS 2-Way Valves ANSI Flanged Valves Flush Tank Valves Angle Stem Flush Tank 3-Way Diverter Valves 3, 4, & 5-Way Valves Transmitter Isolation Valves Instrument Valves Fabflex Manifold Assemblies S, AN V-ball Valves SRIS for Flow Control PA Automation SRIS & Controls www.pbmvalve.com

Features n Adjust-O-Seal feature PBM valves provide bidirectional upstream sealing. n Valve body bolts can be tightened to compensate for normal seat wear without having to remove the valve from service. Competitor s Design PBM s Design Seals at downstream seat Seals at upstream seat Line pressure pushes ball downstream in the ball-closed position, providing sealing at the downstream seat. There is no adjustment to compensate for seat wear. Valve body bolts compress valve seats against the ball, providing bidirectional sealing at the upstream seat. To compensate for seat wear, body bolts can be slightly tightened to recompress seats against ball. PBM valves offer value over the life of the product with: n n n n Fewer process interruptions Longer life Clean/drain without process interruption Improved product yields PBM also offers: n n n On-time delivery Documentation Solutions to tough applications This means on valves mounted vertically like PBM s angle stem flush tank valve, the valve seats on the upstream seat, thus allowing the body to be purged and drained without process interruption.

Table of Contents Industrial Valves ITM PAG Features 2 Ordering information 4-5 Materials of Construction 6 Seat & Seal materials 6 Allowable working pressures and temperature 7 Pressure and temperature charts; Cv factors 8 Torque values 9 Testing 10 Available options 10-11 Flow patterns 12-13 Specifications 14-15 3 DIMNSIONAL INFORMATION, MANUAL & AUTOMATD S series 2-way 16-17 AN series ANSI 18-19 F series Flush Tank 20-21 AF series Angle Stem Flush Tank 22-23 D series 3-way Diverter 24-25 M series 3, 4, & 5-way Multi-port 26-29 TI series Transmitter Isolation valve 30 IM Series Instrument valves 31 Special Application valves 32-33 Automation 34-35 Rep locations 36

Ordering Information for PBM Industrial Valves Number in "( )" represents part number position. Product (1-2) Material (3-4) Size ( 5) Series (6) nd Connection (7-8) Seat & Seal / Filler / O-ring (9) SP Industrial 2-way H- 316 Stainless A 1/4" 1 ANSI, AF, Brz and Iron MP Q- Female NPT G TFM / None / Viton SD Indust, Steam 2-way HL 316L Stainless B 3/8" 3 Firesafe ANSI, AF U- Socket Weld J TFM / VTF / Viton AN ANSI - Carbon Steel C 1/2" 4 S/S and C/S MP B- Buttweld Sch 40 1 A RTF / None / Viton FT Flush Tank 2-way N- 922 Bronze D 3/4" 5 Series 5 (SP, FT, DD, SD C- Buttweld Sch 5 1 B RTF / VTF / Viton AF Angle Stem FT C- Hastelloy C-276 1" DP, CT, SM, SB, SA, FA D- Buttweld Sch 10 1 C VTF / None / Viton DP Diverter Port 3-way C1 Hastelloy B-2 F 1 1/4" 6 Series 5 Firesafe 2-way only 150# Flange D VTF / VTF / Viton DD Diverter Steam Y- Hastelloy C-22 G 1 1/2" M- 300# Flange H S-tef TM / None / Viton MP Multi-port B- 836 Bronze H 2" N- 600# Flange I S-tef TM / VTF / Viton TI Transmitter Isolation R- 955 Al-Brz J 2 1/2" O- Grooved K UHMWP / None / Viton X- 958 Ni-Al-Brz K 3" K- Cam Lock L UHMWP / VTF / Viton 9-954 Al-Brz L 4" P- Male NPT M UHMWP / UHMWP / Viton Z- 70/30 Cu-Ni M 6" R- Sil Braze N PK / None / Kalrez 1-90/10 Cu-Ni N 8" S- Sil Braze (1) Groove O PK / VTF / Kalrez P- AL6XN P 10" T- Solder Joint P PK / PK / Kalrez I- Inconnel 600 W- Tri-Clamp Pipe Q Carbon - Graphite M- Monel 400 -Z No nd Fittings R Kynar / None / Viton S- 953 Al-Brz S Kynar / Kynar / Viton T- Gr 5 Titanium T VTF / None / PR W- Nickel 200 Notes: U VTF / VTF / PR D- Iron 1. xtended butt weld end fittings are standard V RTF / None / PR A- Aluminum on Series 5 & 6 valves. W RTF / VTF / PR 25 254 SMO 6 -moly 2. All options are not available on all valve styles Z TFM / None / PR 22 Duplex 2205 3. For valves with (2) different end connections, use 0 S-tef TM / None / PR 76 Super duplex both end codes, for example LQ = 150# flanged 1 S-tef TM / VTF / PR 32750 / 32760 by female NPT 2 TFM / VTF / PR 55 Ferralium 255 3 UHMWP / None / PR 4 UHMWP / VTF / PR 5 UHMWP / UHMWP / PR 6 PK / None / Viton 7 VTF / None / ncapsulated Viton 8 RTF / None / ncapsulated Viton INDUSTRIAL VALVS (Series 5) 9 TFM / None / ncapsulated Viton Industrial 2-way VALV TYP SP Industrail flush tank FT FD TFM TM is standard for Seres 5 & 6 Industrail diverter valve 3 way DP DD RTF is standard seat material for Series 1 valves. Standard STANDARD SATS NCAPSULATD SATS STAM SRVIC Options 1 + 2 3 + 4 5 6 7 + 8 9 10 + 11 12 13 + 14 15 Product Material Size Series nd Fitting Seat/Seal Flow Pattern Ball/Stem Operator Polish Purge Ports. Ball Flats SP H- H 5 Q- G - - G 34 - SPH-H5Q-G G34- is the code f or a SP Industrial 2 -way, 316 stainless steel, 2 inch size, Series 5, FNPT end connections, TFM seats and seals, 17-4 PH stem, 80 psig Spring Return Actuator. - - SD TFM TM is a registered trademark of Dyneon TM, a 3M Company S-TF TM is 50% 316 stainless steel and 50% PFF. www.pbmvalve.com PBM, Inc. Valve Solutions - 1070 Sandy Hill Road - Irwin, PA 15642 - Phone: 724.863.0550 - Fax: 724.864.9255 - mail: info@pbmvalve.com

Ordering Information for PBM Industrial Valves cont. Flow Pattern / Flush Tank Pad / Aseptic (Pos 10-11) Ball / Stem (Pos 12) Operator (13-14) Polish (15) (max values) For Non-Flow Pattern, Non-Flush Tank, Non Aseptic, Use " - - " - Standard - - w/ lever operator - No polish For Valves with Flow Patterns, enter the 2 digit flow pattern no. B w/4" stem extension 01 w/o handle A 20 RA ID For all non-aseptic Flush Tank Valves, Use codes below w/4" stem ext, & internal 02 w/o handle, w/ actuator prep B 32 RA OD - - Standard Flush Tank Pad and external ground 03 w/ handle, w/ actuator prep. C 20 RA ID, 32 RA OD 02 No Pad w/ shipping pad F w/ internal and external 04 w/ locking handle D 15 RA ID 04 w/ 316L barstock pad ground 05 w/ stainless oval handwheel 10 RA ID 05 w/ 1" bolt on flat pad G w/ 17-4 PH stem 06 w/ manual safety nut F 20 RA ID after 06 w/ 1.5" bolt on flat pad I w/ monel ball 07 w/ 45 degree handle electropolish 07 w/ 2" bolt on flat pad J w/ 932 bronze ball 08 w/ gear operator G 15 RA ID after 08 w/ 3" bolt on flat pad K w/ monel stem, followers 09 w/ T handle electropolish 09 w/ 4" bolt on flat pad L w/monel ball, stem, 10 w/ manual spring return handle H 10 RA ID after 10 w/ 6" bolt on flat pad and followers 11 w/ fusible link spring return electropolish 11 w/ 8" bolt on flat pad M w/ aluminum ball handle I 5 RA ID N w/ 922 bronze ball 12 w/ vane actuator for 80 psig K 5 RA ID & 32 RA OD For all aseptic valves, use the codes below: O w/ hastelloy C-276 ball 13 w/ nema 4 120 VAC electric actr L 20 RA ID & 32 RA OD Purge Ports (10) Ball Flats & holes (11) P w/ has C-276 ball,stem, 14 w/ nema 7 120 VAC electric actr after electropolish M (1) 1/4" FNPT on center, 90 #1 #2 Use column #1 for and followers 15 w/ square operating nut M lectropolish only degrees from stem 2 way or aseptic FT Q w/ 922 ball, monel stem 16 w/ locking handle,w/ actr mount (ID & OD) N (1) 1/4" FNPT on center, w/ std. Pad. Use and followers body N 10 RA ID & 32 RA OD opposite stem column #2 if valve is R w/ monel stem, followers 17 w/ 4" ext. locking oval handwheel O 15 RA ID & 32 RA OD O (1) 1/4" FNPT upstream, 90 aseptic FT with and bolting 18 w/ 4" ext. locking lever handle after electropolish degree from stem shipping pad. S w/monel ball,stem, 20 w/ DA 80 psig actr. Q 15 RA ID & 32 RA OD P (1) 1/4" FNPT downstream, A K flats, closed. dwnstrm followers and bolting 21 w/ DA 80 psig actr., N 4 L.S. S 10 RA ID & 32 RA OD opposite stem B L flats, closed, upstrm T w/ 922 ball, monel stem & 22 w/ DA 80 psig actr, N 4 Sol. after electropolish Q (2) 1/4" FNPT on center, 90 C M flats, open, upstrm followers, sil-brz bolting 23 w/ DA 80 psig actr, N 4 L.S. & Sol. degree from & opposite stem D N flats, open, dwnstrm U with CuSi fasteners 24 w/ DA 80 psig actr, N 7 L.S. R (2) 1/4" FNPT upstream, 90 O flats, open, up & 25 w/ DA 80 psig actr, N 7 Sol. Optional 16th Position deg frn & dwnstream opp stem downstream 26 w/ DA 80 psig actr, N 7 L.S. & Sol. LOX Cleaning (16) - no purge. Use only if adding F P holes, closed, dwnstr 27 w/ DA 60 psig actr. L Oxygen Service Cleaning ball flats or drain holes G Q holes, closed, upstrm 28 w/ DA 60 psig actr., N 4 L.S. per PBM Procedure UNIQU PART NUMBRS, FXXX, GXXX, HXXX H R holes, open, upstrm 29 w/ DA 60 psig actr, N 4 Sol. I S holes, open, dwnstrm 30 w/ DA 60 psig actr, N 4 L.S. & Sol. J T holes, open, up & 31 w/ DA 60 psig actr, N 7 L.S. downstream 32 w/ DA 60 psig actr, N 7 Sol. - U No flats or holes 33 w/ DA 60 psig actr, N 7 L.S. & Sol. V 2 std width slotted ball 34 w/ SR 80 psig actr. Operator (13-14) continued W 3 30 degree V ball 35 w/ SR 80 psig actr., N 4 L.S. Codes for Asco Limit Switch X 4 45 degree V ball 36 w/ SR 80 psig actr, N 4 Sol. 55 w/ DA 80 actr., N 4 L.S. Y 5 60 degree V ball 37 w/ SR 80 psig actr, N 4 L.S. & Sol. 56 w/ DA 80 actr, N 4 L.S. & Sol. Z 6 90 degree V ball 38 w/ SR 80 psig actr, N 7 L.S. 57 w/ DA 80 psig actr, N 7 L.S. 1 7 120 degree V ball 39 w/ SR 80 psig actr, N 7 Sol. 58 w/ DA 80 actr, N 7 L.S. & Sol. 8 9 self flushing ball 40 w/ SR 80 psig actr, N 7 L.S. & Sol. 59 w/ DA 60 psig actr., N 4 L.S. "-XXX designates a unique part number where PBM's traditional part number cannot completely describe the valve. For xample, a sepecial actuator, solenoid, etc. 41 w/ SR 60 psig actr. 60 w/ DA 60 actr, N 4 L.S. & Sol. 42 w/ SR 60 psig actr., N 4 L.S. 61 w/ DA 60 psig actr, N 7 L.S. 43 w/ SR 60 psig actr, N 4 Sol. 62 w/ DA 60 actr, N 7 L.S. & Sol. 44 w/ SR 60 psig actr, N 4 L.S. & Sol. 63 w/ SR 80 psig actr., N 4 L.S. 45 w/ SR 60 psig actr, N 7 L.S. 64 w/ SR 80 actr, N 4 L.S. & Sol. 46 w/ SR 60 psig actr, N 7 Sol. 65 w/ SR 80 psig actr, N 7 L.S. 47 w/ SR 60 psig actr, N 7 L.S. & Sol. 66 w/ SR 80 actr, N 7 L.S. & Sol. 51 w/ DA 80 psig actr, beacon 67 w/ SR 60 psig actr., N 4 L.S. 52 w/ DA 60 psig actr, beacon 68 w/ SR 60 actr, N 4 L.S. & Sol. 53 w/ SR 80 psig actr, beacon 69 w/ SR 60 psig actr, N 7 L.S. 54 w/ SR 60 psig actr, beacon 70 w/ SR 60 actr, N 7 L.S. & Sol. www.pbmvalve.com PBM, Inc. Valve Solutions - 1070 Sandy Hill Road - Irwin, PA 15642 - Phone: 724.863.0550 - Fax: 724.864.9255 - mail: info@pbmvalve.com

Industrial Valves Materials Stainless Steel 316 S/S complies with ASTM A 351-CF8M or A 4 7 9, S 3 1 6 0 0 316L S/S complies with ASTM A 351-CF3M or A479, S31603 Is exceptionally corrosion-resistant to acidic and basic environments and does not pit easily. Can be polished to a near-mirror finish for easy cleanability. Weld fittings have a carbon content of <.03% to facilitate welding. Carbon Steel, A 2 1 6 - W C B This versatile material handles mildly corrosive media. B ronze, A l l oy 922 xcellent resistance to sea water environments and good steam resistance. Also, suitable for sub-zero tempera t u r e a p p l i c a t i o n s. H a s t e l l oy C-276 Very good corrosion in reducing and mildly oxidizing environments. Very good resistance to localized attack and ve r y good resistance to stress corrosion cra cking. A l l oy CW-12MW in cast form. Others Additional materials are available, including A l l oy 20, Bronze, Duplex Stainless Steels, Hastelloys, Titanium, and Inconel. Seat and Seal Materials Designation Description Color Purpose TFM RTF Chemically Modified PTF PBM Standard for Series 5 & 6 Glass Reinforced PTF White Slightly Off White VTF Virgin PTF White S-TF TM Stainless Steel Reinforced PTF Charcoal Gray CARBON Carbon/Graphite Black UHMWP Ultra High Molecular Weight Polyethylene Off White PK Poly ether ether ketone Putty This chemically modified PTF material is PBM s standard seat and seal material. It combines the ruggedness of a filled PTF with the low coefficient of friction of virgin PTF. TFM also has much improved porosity control and deformation under load when compared to PTF grades. FDA and USP Class VI compliant. Meets bubbletight seat leakage. Used in a wide variety of applications. Bubbletight leakage. A low stem torque material ideal for sanitary use. FDA and USP Class VI compliant. Meets bubbletight seat leakage. A suitable material for higher pressure/temperature applications. Higher stem torque than virgin grades and TFM. USP Class VI compliant. Meets bubbletight seat leakage. A hard material impervious to high temperatures. Can withstand up to 750 F (400 C) and is used for heat transfer fluid applications and other high temperature applications. Meets Class V seat leakage. Suitable for applications under 200 F. An extremely wear resistant material having a wear rate about 1/10th that of PTF. FDA compliant and is used in high cycle applications where possible. Meets bubbletight seat leakage. For applications up to 500 F. PK is a rugged, high strength material having fairly high stem torque. PBM s PK is 10 weight percent PTF to reduce the hardness of virgin PK. FDA compliant and meets Class V seat leakage. KYNAR Polyvinylidene Fluoride Slightly Transparent White Suitable for applications under 250 F. Kynar has been used successfully in abrasive service and is suitable for radiation environments where gamma levels accumulate to 1,000 megarads. FDA and USP Class VI compliant. Meets bubbletight seat leakage. NOTS: 1. PTF is Polytetrafluorethylene. 2. Seat and seal materials may be mixed in a valve in order to provide media-compatibility and the appropriate torque, temperature and pressure ratings.

Industrial Valves Allowable Working Pressures and Temperatures Non-Flanged 150# Flanged Valve Style/Series Series 5 SP, SD, DP, DD SP, FT, Series 6 AN Series 1 and 3 150# Class MP All Series 1 MP, All Series 4 AF Series 1 AF Series 3 FT, FD Series 5 FD Series 6 TIV Series Notes: Material Size (inches) -20 to 100 F -28.9 to 37.8 C 300 F 1 4 8. 9 C 450 F 232.2 C -20 to 100 F -28.9 to 37.8 C 300 F 1 4 8. 9 C 450 F 232.2 C psig barg psig barg psig barg psig barg psig barg psig barg 316 SS/316L 1-1/2 (DN40) and smaller 900 62.1 770 53.1 680 46.9 275 19.0 205 14.1 195 13.4 316 SS/316L 2 and larger 720 49.6 620 42.7 540 37.2 275 19.0 205 14.1 195 13.4 C-276 1-1/2 (DN40) and smaller 600 41.4 520 35.9 450 46.9 230 15.9 200 13.8 180 12.4 C-276 2 (DN50) and larger 600 41.4 520 35.9 450 46.9 230 15.9 200 13.8 180 12.4 Carbon Stl. 1-1/2 (DN40) and smaller 900 62.1 770 53.1 680 46.9 285 19.7 230 15.9 185 12.8 Carbon Stl. 2 (DN50) and larger 740 51.0 655 45.2 620 42.7 285 19.7 230 15.9 185 12.8 922 Bronze 1-1/2 (DN40) and smaller 600 41.4 600 41.4 580 40.0 225 15.5 180 12.4 135 9.3 922 Bronze 2 (DN50) and larger 600 41.4 600 41.4 580 40.0 225 15.5 180 12.4 135 9.3 316 SS/316L 3 (DN80) and under 720 49.6 620 42.7 540 37.2 275 19.0 205 14.1 195 13.4 Carbon Stl. 3 (DN80) and under 740 51.0 655 45.7 620 42.7 285 19.7 230 15.9 185 12.8 316 SS/316L All n/a n/a n/a 275 19.0 205 14.1 195 13.4 C-276 All n/a n/a n/a 230 15.9 200 13.8 180 12.4 Carbon Stl. All n/a n/a n/a 285 19.7 230 15.9 185 12.8 836 Bronze All n/a n/a n/a 225 15.5 180 12.4 135 9.3 836 Bronze 1-1/2 (DN40) and smaller 400 27.6 385 26.5 360 24.8 225 15.5 180 12.4 135 9.3 836 Bronze 2 (DN50) 350 24.1 340 23.4 315 21.7 225 15.5 180 12.4 135 9.3 836 Bronze 3 (DN80) 300 20.7 290 20.0 270 18.6 225 15.5 180 12.4 135 9.3 836 Bronze 4 (DN100) n/a n/a n/a 225 15.5 180 12.4 135 9.3 316 SS/316L 3/4 (DN20) and smaller 900 62.1 770 53.1 680 46.9 275 19.0 205 14.1 195 13.4 316 SS/316L 1 (DN 25) thru 4 (DN100) 720 49.6 620 42.7 540 37.2 275 19.0 205 14.1 195 13.4 316 SS/316L 6 (DN150) 275 19.0 205 14.1 195 13.4 275 19.0 205 14.1 195 13.4 C-276 3/4 (DN20) and smaller 900 62.1 770 53.1 680 46.9 230 15.9 200 13.8 180 12.4 C-276 1 (DN25) thru 4 (DN100) 720 49.6 620 42.7 540 37.2 230 15.9 200 13.8 180 12.4 C-276 6 (DN150) 275 19.0 205 14.1 195 13.4 230 15.9 200 13.8 180 12.4 Carbon Stl. 3/4 (DN20) and smaller 900 62.1 770 53.1 680 46.9 285 19.7 230 15.9 185 12.8 Carbon Stl. 1 (DN25) thru 4 (DN100) 740 51.0 655 45.7 620 42.7 285 19.7 230 15.9 185 12.8 Carbon Stl. 6 (DN150) 300 20.7 250 17.2 220 15.2 285 19.7 230 15.9 185 12.8 316 SS/316L 1-1/2 (DN40) and smaller 900 62.1 770 53.1 680 46.9 275 19.0 205 14.1 195 13.4 316 SS/316L 2 (DN50), 4 (DN100) 550 37.9 540 37.2 525 36.2 275 19.0 205 14.1 195 13.4 316 SS/316L 3 (DN80) 625 43.1 610 42.1 6 0 0 46.9 275 19.0 205 14.1 195 13.4 316 SS/316L 6 (DN150) 375 25.9 3 6 5 25.2 360 24.8 275 19.0 205 14.1 195 13.4 C-276 1-1/2 (DN40) and smaller 600 41.4 520 35.9 475 32.8 230 15.9 200 13.8 180 12.4 C-276 2 (DN50), 4 (DN100) 550 37.9 540 37.2 525 36.2 230 15.9 200 13.8 180 12.4 C-276 3 (DN80) 600 41.4 520 35.9 475 32.8 230 15.9 200 13.8 180 12.4 C-276 6 (DN150) 375 25.9 320 22.1 280 19.3 230 15.9 200 13.8 180 12.4 Carbon Stl. 1-1/2 (DN40) and smaller 900 62.1 770 53.1 680 46.9 285 19.7 230 15.9 185 12.8 Carbon Stl. 2 (DN50) 550 37.9 550 37.9 550 37.9 285 19.7 230 15.9 185 12.8 Carbon Stl. 3 (DN80) 625 43.1 625 43.1 625 43.1 285 19.7 230 15.9 185 12.8 Carbon Stl. 4 (DN100) 550 37.9 550 37.9 550 37.9 285 19.7 230 15.9 185 12.8 Carbon Stl. 6 (DN150) 375 25.9 375 25.9 375 25.9 285 19.7 230 15.9 185 12.8 316 SS/316L 1-1/2 (DN40) and smaller 720 49.6 620 42.7 540 37.2 275 19.0 205 14.1 195 13.4 316 SS/316L 2 (DN50), 4 (DN100) 550 37.9 540 37.2 525 36.2 275 19.0 205 14.1 195 13.4 316 SS/316L 3 (DN80) 625 43.1 610 42.1 600 41.4 275 19.0 205 14.1 195 13.4 316 SS/316L 6 (DN150) 375 25.9 365 25.2 360 24.8 275 19.0 205 14.1 195 13.4 Carbon Stl. 1-1/2 (DN40) and smaller 740 51.0 655 45.2 620 42.8 285 19.7 230 15.9 185 12.8 Carbon Stl. 2 (DN50), 4 (DN100) 550 37.9 550 37.9 550 37.9 285 19.7 230 15.9 185 12.8 Carbon Stl. 3 (DN80) 625 43.1 625 43.1 625 43.1 285 19.7 230 15.9 185 12.8 Carbon Stl. 6 (DN150) 375 25.9 375 25.9 375 25.9 285 19.7 230 15.9 185 12.8 316 SS/316L All 720 49.6 620 42.8 540 37.2 275 19.0 205 14.1 195 13.4 C-276 All 720 49.6 620 42.8 540 37.2 230 15.9 200 13.8 180 12.4 Carbon Steel All 740 51.0 655 45.2 620 42.8 285 19.7 230 15.9 185 12.8 316 SS/316L All n/a n/a n/a 275 19.0 205 14.1 195 13.4 317L SS All n/a n/a n/a 275 19.0 205 14.1 195 13.4 C-276 All n/a n/a n/a 230 20.0 200 15.9 180 12.4 Ti Grade 5 All n/a n/a n/a 275 19.0 240 16.5 200 13.8 1. Bronze, 316 SS and C-276 retain their CWP below minus 20 F. 2. All valves rated for full vacuum. 7

Industrial Valves 1000 1-1/2 Valves 1-1/2-Inch and smaller and Smaller 2 2-Inch to 3-Inch 3 800 900 700 800 700 600 Pressure (psig) 600 500 400 UHMWP VTF RTF/TFM SS/TF PK Pressure (psig) 500 400 UHMWP VTF RTF/TFM 300 SS/TF 300 PK 200 200 100 100 8 0 0 50 100 150 200 250 300 350 400 450 500 Temperature (F) Seat & Seal Temperature and Pressure Charts Pressure (psig) 600 500 400 300 200 4 and 6-Inch 4 to 6 0 0 100 200 300 400 500 600 Temperature (F) UHMWP VTF RTF/TFM SS/TF PK 100 Cv Values VALV SIZ 2-WAY FLUSH TANK DIVRTR PORT SP AN AF FT DP SRIS 5 S/S DP SRIS 1 BRONZ PORT T-PORT PORT T-PORT SRIS 5 SRIS 1 SRIS 1 SRIS 5 STRAIGHT BRANCH STRAIGHT BRANCH 1/4" 5* 3/8" 10* 1/2" 12 31 14 6.6 7.4 5.2 12 14 8.7 3/4" 42* 52 42 17 20 13 21 25 16 1" 73 80 65 70 33 39 24 33 39 24 1-1/4" 1-1/2" 170 190 143 190 79 93 58 79 93 58 2" 360 400 280 370 149 180 110 149 180 110 2-1/2" 650 600 3" 935 1,100 700 900 350 415 250 290 345 210 4" 1,900 2,400 880 1,650 640 770 465 460 540 340 6" 4,800 5,600 1,500 3,900 1,550 1,860 1,110 1,050 1,220 790 8" 10,700 7,400 10" 17,400 150# Flanged and Butt Weld, unless indicated otherwise noted (gpm at 1 psi d/p) VALV SIZ MULTI-PORT MP SRIS 4 (S/S, CARBON) MP SRIS 1 (BRONZ, DUCTIL) PORT T-PORT LPORT PORT T-PORT LPORT STRAIGHT BRANCH STRAIGHT BRANCH 1/2" 6.6 7.4 5.2 6.6 12 14 8.7 6.6 3/4" 17 20 13 16 17 20 13 16 1" 33 39 24 27 33 39 24 27 1-1/4" 32 36 23 26 32 37 23 26 1-1/2" 79 93 58 73 79 93 58 73 2" 149 180 110 128 149 180 110 128 3" 350 415 250 300 200 250 140 180 4" 640 770 465 530 365 450 260 340 6" 1,550 1,860 1,110 1,210 1,550 1,860 1,110 770 *Q (FNPT) ends 0 0 50 100 150 175 200 250 300 350 400 450 500 Temperature (F)

Stem Torque Valve Style/ Series All Series 5 & 6 2-Way and 3- Way AN Series 1 and 3 MP Series 1 MP Series 4 Valve Size (in.) As built Torque 0 psig 0 barg 100 psig 6.9 barg 200 psig 13.8 barg Differential Pressure across Seats 300 psig in.-lb. N-m in.-lb. N-m in.-lb. N-m in.-lb. N-m in.-lb. N-m in.-lb. N-m in.-lb. N-m in.-lb. N-m in.-lb. N-m 1/4 32 3.6 64 7.2 64 7.2 64 7.2 64 7.2 64 7.2 64 7.2 64 7.2 64 7.2 1/2 32 3.6 64 7.2 64 7.2 64 7.2 64 7.2 64 7.2 64 7.2 64 7.2 64 7.2 3/4 40 4.5 80 9.0 80 9.0 80 9.0 80 9.0 80 9.0 96 10.8 112 10.8 128 12.7 20.7 barg 400 psig 27.6 barg 500 psig 34.5 barg 1 58 6.6 116 13.1 116 13.1 116 13.1 150 16.9 185 20.9 220 24.9 trun. 1-1/2 154 17.4 308 34.8 308 34.8 440 49.7 580 65.5 715 80.8 trun. trun. 2 182 20.6 364 41.1 364 41.1 635 71.7 910 102.8 1,180 133.3 trun. trun. 2-1/2 288 32.5 576 65.1 576 65.1 1,200 135.6 1,600 180.8 trun. 3 430 48.6 860 97.2 860 97.2 1,560 176.3 trun. trun. 4 787 88.9 1,570 177.4 2,650 299.4 trun. trun. 6 1,920 217.0 3,840 433.9 7,100 8 0 2. 3 Use trunnion above 75 psid. 1/2 32 3.6 64 7.2 64 7.2 64 7.2 64 7.2 3/4 4 0 4.5 80 9.0 80 9.0 80 9.0 80 9.0 1 60 6.8 120 13.6 120 13.6 120 13.6 120 13.6 1-1/2 132 14.9 264 29.8 264 29.8 280 31.6 390 4 4. 1 2 156 17.6 312 35.3 312 35.3 545 61.6 785 88.7 3 336 38.0 672 75.9 1,050 118.7 1,950 220.4 trun. trun. 4 720 58.6 1,440 162.7 2,650 299.5 trun. trun. 6 1,560 176.3 3,120 352.6 7,100 802.3 Use trunnion above 75 psid. 1/2 77 8.7 144 16.3 144 16.3 144 16.3 144 16.3 144 16.3 3/4 77 8.7 144 16.3 144 16.3 144 16.3 144 16.3 144 16.3 1 192 21.7 385 43.5 385 43.5 385 43.5 385 43.5 385 43.5 1-1/4 192 21.7 385 43.5 385 43.5 385 43.5 385 43.5 385 43.5 1-1/2 384 43.4 770 87 770 87 770 87 940 106.2 trun. trun. 2 432 48.8 865 97.7 865 97.7 865 97.7 1,200 135.6 trun. trun. 3 576 65.1 1,150 129.9 1,150 129.9 1,620 183 2,100 237.3 trun. trun. 4 864 9 7. 6 1,700 192.1 3,000 339 trun. trun. 1/2 77 8.7 144 16.3 144 16.3 144 16.3 144 16.3 144 16.3 144 16.3 144 16.3 144 16.3 3/4 77 8.7 144 16.3 144 16.3 144 16.3 144 16.3 144 16.3 144 16.3 144 16.3 144 16.3 1 192 21.7 385 43.5 385 43.5 385 43.5 385 43.5 385 43.5 385 43.5 440 49.7 trun. trun. 1-1/4 192 21.7 385 43.5 385 43.5 385 43.5 385 43.5 385 43.5 385 43.5 440 49.7 trun. trun. 1-1/2 384 43.4 770 87 770 87 770 87 940 106.2 trun. trun. 2 432 48.8 865 97.7 865 97.7 865 97.7 1,200 135.6 trun. trun. 3 864 97.6 1,730 195.5 1,730 195.5 trun. trun. 4 1,920 216.9 3,840 433.9 3,840 433.9 trun. trun. Minimum Actuator Sizing Torque vs. Differential Pressure TFM or VTF Seats 6 3,000 339.0 6,000 678.0 8, 8 0 0 994.4 Use trunnion above 75 psid. Industrial Valves Notes: 1. For valves with UHMWP and RTF seats, multiply the above values by 1.25 2. For valves which have SS/TF or Kynar seats multiply the above values by 1.56. 3. For valves with PK seats multiply the above values by 1.7. 4. Where trunnion is indicated, PBM recommends trunnion mounting the ball to avoid excessive seat loads and stem torques. 5. For Series 5 SD valves, 2-1/2 and larger, with RTF seats, multiply the torques in the table by 1.56. 600 psig 41.4 barg 700 psig 48.3 barg 9

Industrial Valves 0 Testing n Vacuum Testing n Cycle Testing n Shock and Vibration n Seismic n Hydrostatic n Material Test Reports - Physical testing - Chemical testing Steam Valves Options n Cryogenic n USCG Category A n Manual Spring Return Handles n Internal & xternal Grounding n LOX (Cleaned for Oxygen Service) n Mechanical & lectro-polishing n Body Cavity Fillers n Direct Mount Actuation n Steam Seats (ncapsulated) n Positioners n Purge Ports (SIP/CIP) n Fieldbus, AS-i, DeviceNet n Fire Rated, API 607 n Ball Flats or Purge Holes n Dribble Control Units n Locking Handle n High Alloys n xtended Locking Handle n Fabflex Manifolds n Cylindrical Radius Weld Pads n Self Cleaning Flushable Ball n V-Balls for Flow Control

Options Industrial Valves 1 Cylindrical Radius Pad Direct Mount Actuation Cavity Fillers Purge Ports, Milled Flats and Purge Holes Locking Handle

Industrial Valves Flow Pattern Diagrams The diagrams show the top view as though you were looking down on the stem. White areas indicate the path available for process flow. Shaded areas indicate unused ports for a given flow position. Diverter Port Patterns By specifying a T- Port, Double T- Port, Angle Port (L) or Double Angle Port (LL) Ball, different flow configurations are possible. For example, a DP va l ve with a T- Port Ball might be used to control flow to one or two simultaneous operations. The side entry Angle Port Ball and the bottom entry Double Angle Po r t Ball are ideal for connecting two relief va l ves to a system. Th e Double Angle Port Ball diverts flow from one outlet to another outlet 180 away, with only 90 stem rotation. This allows use of 90 double acting or spring return actuation, instead of 180. SID NTRY C o d e 0 3 0 4 0 6 10 T- Po r t T- Po r t T- Po r t L - Po r t 90 Tu r n 90 Tu r n 180 Tu r n 90 Tu r n 3-Way Multi-Port Patterns 3 - way Multi-Ports are a popular choice in a variety of industries. A seal at every port distinguishes the 3-way MP/MI Series va l ve from d iverting-type va l ves. In some applications, the 3-way MP/MI va l ve can take the place of two or three 2-way va l ves, with corresponding s avings in piping and fittings. For applications requiring simultaneous process line changes, two 3-way MP/MI Series va l ves may be mounted in tandem and controlled with a single actuator or handle for greater control and additional savings. Additional flow patterns are possible by using manifolds of two or more va l ve s. SID NTRY 0 1 0 2 0 3 0 4 0 5 0 6 0 7 T- Po r t T- Po r t T- Po r t T- Po r t T- Po r t T- Po r t T- Po r t 90 Tu r n 90 Tu r n 90 Tu r n 90 Tu r n 180 Tu r n 180 Tu r n 180 Tu r n Position A Position A Position B Position B Position C Position C 0 8 0 9 1 0 1 1 1 2 1 3 T- Po r t T- Po r t L - Po r t L - Po r t L - Po r t L - Po r t 180 Tu r n 360 Tu r n 90 Tu r n 180 Tu r n 180 Tu r n 360 Tu r n Position A BOTTOM NTRY 1 4 1 5 1 6 1 7 1 8 L - Po r t L - Po r t T- Po r t T T- Po r t L L - Po r t 360 Tu r n 180 Tu r n 90 Tu r n 180 Tu r n 90 Tu r n Position B Position C Position A Position D Position B Position C Position D BOTTOM NTRY Position A Position B 1 4 1 5 1 6 1 7 1 8 1 9 L - Po r t L - Po r t T- Po r t T T- Po r t L L - Po r t L - Po r t 360 Tu r n 180 Tu r n 90 Tu r n 180 Tu r n 90 Tu r n 90 Tu r n Position C Position D

Industrial Valves 4 - way Multi-Ports are a true Multi-Port va l ve with seals at eve r y port. This design makes the 4-way MP/MI Series ideal for flow sw i t ching operations. In some applications, this va l ve can replace as many as four ordinary 2-way va l ves, with corresponding savings in piping and fittings. The follow i n g i l l u s t rations show how different ball and port configura t i o n s create many flow patterns with a single 4-way Multi-Po r t. 4-Way Multi-Port Patterns BOTTOM NTRY 2 0 2 1 2 2 2 3 2 4 2 5 2 6 2 7 Double Po r t Double Po r t Double Po r t Double Po r t Double Po r t Double Po r t L - Po r t T- Po r t 90 Tu r n 180 Tu r n 180 Tu r n 180 Tu r n 180 Tu r n 360 Tu r n 360 Tu r n 90 Tu r n 4-Way Multi-Port Patterns Position A Position B Position C Position D SID NTRY 3 7 3 8 3 9 4 0 4 1 4 2 4 3 Double Po r t L - Po r t L - Po r t T- Po r t S t raight Po r t T- Po r t T- Po r t 90 Tu r n 180 Tu r n 360 Tu r n 180 Tu r n 90 Tu r n 90 Tu r n 90 Tu r n 1 2 8 2 9 3 0 3 1 3 2 3 3 3 4 3 5 Double T- Po r t Double T- Po r t Double T- Po r t Double T- Po r t Double T- Po r t Double T- Po r t Double T- Po r t Double T- Po r t 180 Tu r n 180 Tu r n 180 Tu r n 180 Tu r n 360 Tu r n 90 Tu r n 90 Tu r n 90 Tu r n 5-Way Multi-Port Patterns 5 - way Multi-Ports are 5-seated to provide positive shut off and flow control at each port. This design is not only versatile, but extremely economical. In some applications, this va l ve can replace as many as four ordinary 2-way va l ves, with corresponding savings in piping and fittings. The following illustrations show available flow patterns with a single 5-way Multi-Port va l ve. BOTTOM NTRY 4 4 4 5 4 6 4 7 4 8 4 9 5 0 5 1 L - Po r t Double Po r t T- Po r t Double T- Po r t Double T- Po r t Double T- Po r t Double T- Po r t Double Po r t 360 Tu r n 180 Tu r n 90 Tu r n 90 Tu r n 90 Tu r n 180 Tu r n 360 Tu r n 360 Tu r n Position A Position B 3 6 Double T- Po r t 90 Tu r n Position C Position D

Industrial Valves Written Specifications S SRIS S-Series 5: Two - way full port ball va l ve; Body, ball, stem, and end fitting material shall be 316 stainless steel, Hastelloy C-276, Carbon Steel, Hastelloy C-22, bronze alloy 922, or other. Va l ve shall be three-piece swing-out body design. Seats and seals shall be T F M - P T F material and provide both upstream and dow n s t ream bubbletight seal and be adjustable for in-line we a r. Stem packing shall be live loaded T F M -PTF material. For manual va l ves, handle shall be 300 series stainless steel. Body bolts and nuts shall be 18-8 stainless steel. Maximum working pre s s u re to be 720 psig and full vacuum. Va l ves shall be non-firesafe design unless otherwise specified. For fire ra t e d va l ves to API 607 d 4, sizes 1/2 3, designate Series 6 (see section f i re rated ). To add automation and controls, see section Automation and Controls. PBM Model number SP(material)-(size)5(end connection) 4 SD Series 5: Two - way full port steam ball va l ve; Body, ball, stem, and end fitting material shall be 316 stainless steel, Hastelloy C-276, Carbon Steel, Hastelloy C-22, bronze alloy 922, or other. Va l ve shall be three-piece swing-out body Seats shall be T F M -PTF with PR O-ring energizer. Seats shall have stainless steel encapsulation on ID, provide both upstream and dow n s t ream bubbletight seal and be adjustable for in-line we a r. Stem packing shall be live loaded white T F M -PTF. Body seal shall be PR o-rings with white T F M - P T F b a ck up seal. Optional 300 Series s/s 2 stem extension for 4 thick installation. Va l ves shall not re q u i re disassembly for buttwelding. Body bolts, nuts, and belleville washers shall be 18-8 stainless steel. Body bolts shall be live-loaded with belleville washers. Maximum wo r k i n g p re s s u re to be 720 PSIG and full vacuum. Va l ves shall be a non-firesafe design. To add automation and controls, see section Au t o m a t i o n and Controls. PBM Model number SD(material)-(size)5(end connection) AN SRIS Series 1 ANSI: Two-way ANSI flanged full port ball valve; B o dy, ball, stem, and end fitting material shall be 316 stainless steel, Hastelloy C-276, Carbon Steel, bronze, aluminum bronze, or other. Valve shall be two piece split body design. Seats and seals shall be RTF material, with Viton O-ring body seal. Seats shall provide both upstream and downstream bubbletight seal and be adjustable for in-line wear. Stem packing shall be live loaded RTF material. nd fittings shall be ANSI 150# flanged per ANSI B16.5 and face to face dimension shall conform to ASM B16.10 Long Pattern. Valve handle shall be 300 series stainless steel with optional pad locking device allowing valve to pad locked in the open or closed position. Body bolts and nuts shall be 18-8 stainless steel. Maximum working pressure to be as material is rated for 150# flanges to and full vacuum. Valves shall be 100% tested per ASM / ANSI B16.34. Valves shall be non-firesafe design unless otherwise specified. For fire rated valves to API 607 d 4, sizes 1/2 6, designate Series 3 (see section fire rated ). To add automation and controls, see section Automation and Controls. PBM Model number AN(material)-(size)1L F & AF SRIS F-Series 5: Flush tank bottom ball valve; Body, ball, stem, and end fitting material shall be 316 stainless steel, Hastelloy C-276, Carbon Steel, Hastelloy C-22, or other. Weld pad shall be 316L grade stainless steel (or other) material (specify). Valve shall be three-piece swing-out body design. Seats and seals shall be TFM -PTF material and provide both upstream and downstream bubbletight seal and be adjustable for in-line wear. Stem packing shall be live loaded TFM -PTF material. For manual valves, handle shall be 300 series stainless steel. Body bolts and nuts shall be 18-8 stainless steel. Valves shall be non-firesafe design unless otherwise specified. For fire rated valves to API 607 d 4, sizes 1/2 3, designate Series 6. To add automation and controls, see last section. PBM Model number FT(material)-(size)5(end connection) AF Series 1: Angle stem flush tank bottom ball valve. Body, ball, stem, and end fitting material shall be 316 stainless steel, Hastelloy C- 276, Hastelloy C-22, or other. Weld pad shall be 316L grade stainless steel (or other) material (specify). Valve shall be two-piece design. Seats and seals shall be RTF material and provide both upstream and downstream bubbletight seal and be adjustable for inline wear. Stem packing shall be live loaded RTF material. For manual valves, handle shall be 300 series stainless steel. Body bolts and nuts shall be 18-8 stainless steel. Valves shall be non-firesafe design unless otherwise specified. For fire rated valves to API 607 d 4, sizes 1 6, designate Series 3. To add automation and controls, see last section. PBM Model number AF(material)-(size)-1-(end connection) FIR RATD Fire Rated 2-way Industrial, S- and F- 1/2 to 3, AN and AF 1 to 6. Add text: Valve design shall be tested and comply with criteria set forth in API-607 edition 4. Valve body bolts shall be fully encapsulated. Valve design is non-adjust-o-seal. Body seals shall be graphite material isolated from product stream under normal operation conditions by o-ring seals. Upon sublimation of seat and seal

Industrial Valves material in the event of a fire condition, a metal back up seat shall seal the valve at leakage rates in accordance with API- 607 d. 4. Model Number: Same as above, except Series 5 Changes to 6, Series 1 changes to 3. D SRIS D-Series 5, Th re e - way diverter port ball va l ve; Body, ball, stem, and end fitting material shall be 316 stainless steel, H a s t e l l oy C-276, Hastelloy C-22, or other. Va l ve shall be three-piece design. Seats and seals shall be T F M -PTF material and provide both upstream and dow n s t ream bubbletight seal and be adjustable for in-line we a r. Stem packing shall be live loaded T F M -PTF material. For manual va l ves, handle shall be 300 series stainless steel. Body bolts and nuts shall be 18-8 stainless steel. Maximum working pre s s u re to be 720 psig and full vacuum. Specify PBM flow pattern. To add automation and controls, see section Automation and Controls. PBM Model number DP(material)-(size)5(end connection) (flow pattern) M SRIS M-Series 4: Three, four, or five way multi-port ball valve. Body, ball, stem, and end fitting material shall be 316 stainless steel, Carbon Steel, Hastelloy C-276, or other. Valve shall have 4 or 5 TFM -PTF Seats and seals and provide bubbletight seal and be adjustable for in-line wear. Stem packing shall be live loaded TFM -PTF material. For manual valves, handle shall be 300 series stainless steel. Body bolts and nuts shall be 18-8 stainless steel. Maximum working pressure to be 400 psig and full vacuum. Specify PBM flow pattern for 3,4,or 5-way valve. To add automation and controls, see section Automation and Controls. PBM Model number MP(material)-(size)-4-(end connection)-(flow pattern) 1 M-Series 1: Three, four, or five way multi-port ball valve. Body, ball, stem, and end fitting material shall be (Bronze or Ductile Iron). Valve shall have 4 or 5 RTF Seats and seals and provide bubbletight seal and be adjustable for in-line wear. Stem packing shall be live loaded RTF material. For manual valves, handle shall be 300 series stainless steel. Body bolts and nuts shall be 18-8 stainless steel. Maximum working pressure to be 300 psig and full vacuum. Specify PBM flow pattern for 3, 4, or 5-way valve. To add automation and controls, see section Automation and Controls. PBM Model number MP(material)-(size)-1-(end connection)-(flow pattern) TI SRIS TI Series 5: Transmitter Isolation ball valve Valve shall be a PBM Model TI Transmitter Isolation Valve (TIV), 316 stainless steel construction (body, ball,and trim), or optional Hastelloy, Titanium, 317 stainless, others) with 1.0-inch or 2-1/2-inch port diameter, with a tank side flange to accommodate both standard ANSI 3-inch 150-lb. Flange drilling and a 25 to 27 degree offset flange pattern. Instrument side flange shall be drilled to accommodate a standard ANSI 3-inch 150-lb flange drilling. Valve shall have a 1/4 turn manual lockable stainless steel handle. Valve shall have four (4) 1/4 inch NPT purge ports, each filled with a 1/4 inch MNPT plug made from the same material as the valve body. Seat and seal material shall be reinforced Teflon with VTF o-ring. PBM Valve model TI(material)-5A. For 2-1/2 port diameter, PBM Valve model TI(material)-J5A AUTOMATION AND ACCSSORIS PBM s Direct Mount Automated Ball Valves, Valves as specified in Manual Valves section with addition of a Direct Mount double acting or spring return pneumatic actuator. Actuator shall be of the double opposing piston, rack and pinion design with bidirectional pinion travel stops and hard anodized aluminum oxide body with co-deposited fluoropolymer. nd caps to be polyester powder coated with 300 series stainless steel fasteners. Mounting bracket shall be stainless steel and valve stem shall insert directly into actuator drive adapter. Actuator shall be sized utilizing a 100% safety factor. Specify supply air pressure at actuator (60 or 80 psig). PBM Model Number PA PBM s lectric actuators, limit switches, positioners, solenoids, and field bus accessories; Specify according to all statutory and regulatory requirements. Include Nema rating requirements and electrical current.

Industrial Valves S-Series 5 6 Size 1 / 4 " DN 8 3 / 8 " DN 10 1 / 2 " DN 15 3 / 4 " DN 20 1 " DN 25 1-1 / 2 " DN 40 2 " DN 50 2-1 / 2 " DN 65 3 " DN 80 4 " DN 100 6 " Size Code Units Port Dia. 1 A B C Q- U- S- T- A B D F G H Approx. Weight Face to Fa c e B- D- Q- U- S- T- CL to Fa c e B- D- CL t o B o t t o m B- D- Q - S- T- U CL t o To p o f H a n d l e H a n d l e L e n g t h f ro m CL nd Fitting Length U- Length B-, D- Length Dia. x t e n d e d H a n d l e inches 0. 5 0 3. 1 5. 5 1. 5 6 2. 8 0. 9 2. 6 4. 2 0. 4 1. 5 7. 5 1.7 lbs. mm 13 79 140 40 70 23 67 1 0 5 1 0 3 8 1 8 9.8 kg. inches 0. 5 3. 1 5. 5 1. 5 6 2. 8 0. 9 2. 6 4. 2 0. 4 1. 5 7. 5 1.7 lbs. mm 13 79 140 40 70 23 67 1 0 5 1 0 3 8 1 8 9.8 kg. inches 0. 5 3. 1 5. 5 5. 5 1. 5 6 2. 8 2. 8 0. 9 2. 6 4. 2 0. 4 1. 5 3. 5 7. 5 1.7 lbs. 4.0 lbs. mm 13 79. 140 140 40 70 70 23 67 1 0 5 1 0 3 8 8 9 1 8 9.8 kg. 1. 8 k g. D inches 0. 8 3. 4 5. 5 5. 8 1. 7 2. 8 2. 9 1. 0 2. 8 4. 2 0. 5 1. 5 3. 9 7. 6 2.0 lbs. 5.2 lbs. mm 19 87 140 146 44 70 73 2 5 71 1 0 5 1 4 3 8 9 9 1 9 3.9 kg. 2.4 kg. inches 1. 0 4. 3 6. 0 6. 5 2. 1 3. 0 3. 3 1. 3 3 3. 0 5. 1 0. 5 1. 5 4. 3 7. 6 4.5 lbs. 8.7 lbs. mm 25 108 152 165 54 76 83 34 77 1 2 9 1 4 3 8 1 0 8 1 9 4 2.0 kg. 3.9 kg. G inches 1. 5 5. 5 7. 5 8. 0 2. 8 4. 0 4. 0 1. 7 8 4. 1 8. 7 0. 5 1. 5 5. 0 9. 4 10.2 lbs. 17.4 lbs. mm 38 140 191 203 70 95 102 45 104 2 2 1 1 4 3 8 1 2 7 2 4 0 4.6 kg. 7.9 kg. H inches 2. 0 6. 0 8. 0 9. 8 3. 0 4. 0 4. 9 2. 2 4. 4 8. 7 0. 7 1. 8 6. 0 9. 8 15.4 lbs. 26.5 lbs. mm 51 152 203 248 76 102 124 55 112 1 2 1 7 4 5 1 5 2 2 4 8 7.0 kg. 12.0 kg. J K L inches 2. 5 8. 0 1 1. 5 1 1. 5 4. 0 5. 8 5. 8 2. 8 6. 5 1 2. 4 0. 7 2. 3 7. 0 1 1.3 36.0 lbs. 53.5 lbs. mm 64 203 2921 292 102 146 146 71 163 3 1 6 1 8 5 9 1 7 8 2 8 8 16.3 kg. 24.3 kg. inches 3. 0 9. 0 1 3. 5 1 2. 8 4. 5 6. 8 6. 4 3. 1 6. 7 8 1 2. 4 0. 7 2. 3 7. 5 1 1. 7 48 lbs. 68 lbs. mm 76 229 343 324 114 172 162 80 172 3 1 6 1 8 5 9 1 9 1 2 9 6 21.8 kg. 30.8 kg. inches 4. 0 1 2. 0 1 6. 0 1 5. 0 6. 0 8. 0 7. 5 4. 9 7. 3 2 4. 4 0. 8 2. 3 9. 0 C F 109 lbs. 15 7 l b s. mm 102 305 406 381 152 203 191 125 186 6 2 1 2 1 5 9 2 2 9 C F 49.4 kg. 71. 2 k g. DN 150 M inches 6. 0 2 2. 0 2 0. 0 1 1. 0 1 0. 0 7. 3 *Note 3 *Note 3 C F 3. 8 1 1. 0 C F C F C F mm 152 559 508 279 2 5 4 184 *Note 3 *Note 3 C F 9 5 2 7 9 C F C F C F NOT : * L e ver Handle not recommended. B- D- Q- U- 1. Full Po r t 2. CF = Consult Fa c t o r y. 3. Gear operator is recommended if not actuated. F H G D Optional xtended Locking Handle B A Female NPT Q- G Socket Weld U- G Butt Weld B- D- 150# Flange Silver Braze S- Solder Joint T- *922 Alloy Bronze Only

S-Series 5 Actuated Industrial Valves Valve Size 1/4, 3/8, 1/2 DN 8, 10, 15 3/4" DN 20 1" DN 25 1-1/2" DN 40 2" DN 50 2-1/2" DN 65 3" DN 80 4" DN 100 6" DN 150 Actuator TFM or VTF SAT MATRIAL Air Pressure A B C D psig barg inches mm inches mm inches mm inches mm inches Double Acting 60, 80 4. 1 / 5. 5 5.5 139 2.8 71 5.4 136 1.61 40.9 1/8 Spring Return 80 5.5 5.5 139 2.8 71 5.4 136 1.61 40.9 1/8 Spring Return 60 4. 1 6.4 162 3.2 81 5.8 147 1.77 45.0 1/8 Double Acting 60, 80 4. 1 / 5. 5 5.5 139 2.8 71 5.6 140 1.61 40.9 1/8 Spring Return 60, 80 4. 1 / 5. 5 6.4 162 3.2 81 6.0 151 1.77 45.0 1/8 Double Acting 60, 80 4. 1 / 5. 5 5.5 139 2.8 71 6.2 157 1.61 40.9 1/8 Spring Return 60, 80 4. 1 / 5. 5 8.2 207 3.7 95 7.3 184 2.1 52.6 1/8 Double Acting 80 5.5 6.4 162 3.7 95 7.9 201 1.77 45.0 1/8 Double Acting 60 4. 1 8.2 207 3.7 95 8.6 217 2.1 52.6 1/8 Spring Return 60, 80 4. 1 / 5. 5 10.7 272 4.8 123 9.5 242 2.7 68.1 1/4 Double Acting 80 5.5 8.2 207 3.7 95 8.9 225 2.1 52.6 1/8 Double Acting 60 4. 1 8.2 207 3.7 95 8.9 225 2.1 52.6 1/8 Spring Return 80 5.5 10.7 272 4.8 123 9.8 249 2.7 68.1 1/4 Spring Return 60 4. 1 12.9 328 5.4 137 11.0 279 2.9 72.9 1/4 Double Acting 60, 80 4. 1 / 5. 5 12.9 328 5.4 137 12.7 322 2.9 72.9 1/4 Spring Return 80 5.5 12.9 328 5.4 137 12.7 322 2.9 72.9 1/4 Spring Return 60 4. 1 14.4 366 5.8 148 13.1 334 3.2 80.0 1/4 Double Acting 60, 80 4. 1 / 5. 5 12.9 328 5.4 137 13.0 330 2.9 72.9 1/4 Spring Return 80 5.5 14.4 367 5.8 148 13.5 342 3.2 80.0 1/4 Spring Return 60 4.1 16.9 428 6.5 164 14.4 364 3.4 87.0 1/4 Double Acting 60, 80 4.1, 5.5 16.9 428 6.5 164 16.5 419 3.4 87.0 1/4 Spring Return 60, 80 4.1, 5.5 20.6 522 7.4 187 17.0 431 4.0 100.1 1/4 Double Acting 60, 80 4. 1 / 5. 5 22.6 575 8.6 218 23.0 574 4.3 109.0 1/4 Spring Return 80 5.5 22.6 575 8.6 218 23.0 574 4.3 109.0 1/4 Spring Return 60 4. 1 26.5 672 11.4 290 26.2 666 5.7 145.0 1/4 1 A D B C

Industrial Valves AN Series 150# Class 8 A B D F G Approx. Size Units Port Overall C Weight C Length L to nd L to C L to Top of Handle Length Flange Bottom Handle from C Bronze L Diameter 1/2 inches.5 4.3 1.84 1.62 3.1 5.1 3.5 6 lbs. DN 15 mm 13 108 47 41 78 129 89 2.7 kg. 3/4 DN 20 1 DN 25 1-1/2 DN 40 2 DN 50 3 DN 80 4 DN 100 6 DN 150 8 DN 200 10 DN 250 inches.75 4.6 2.0 1.88 3.1 5.1 3.9 9 lbs. mm 19 117 51 48 80 129 99 4.1 kg. inches 1.0 5.0 2.2 2.1 4.3 6.1 4.3 10 lbs. mm 25 127 56 52 110 155 108 4.5 kg. inches 1.5 6.5 2.8 2.4 5.3 8.7 5.0 20 lbs. mm 38 165 71 61 133 221 127 9.1 kg. inches 2.0 7.0 3.0 2.9 5.6 8.7 6.0 24 lbs. mm 51 178 76 73 141 221 152 10.9 kg. inches 3.0 8.0 3.6 4.6 7.1 12.4 7.5 92 lbs. mm 76 203 92 116 180 316 191 41.7 kg. inches 4.0 9.0 3.8 4.8 7.9 14.4 9.0 118 lbs. mm 102 229 98 121 201 367 229 53.5 kg. inches 6.0 15.5 7.3 7.3 N/A N/A 11.0 330 lbs. mm 153 394 186 184 N/A N/A 279 149.7 kg. inches 8.0 18.0 8.5 9.3 N/A N/A 13.5 600 lbs. mm 203 457 216 236 N/A N/A 343 275 kg. inches 10.0 21.0 CF CF N/A N/A 16.0 CF mm 254 533 CF CF N/A N/A 406 CF NOT S: 1. Standard product is 316 Stainless Steel. Carbon Steel, Bronze and other materials are available upon request. Consult PBM. 2. Dimensions meet ASM Standard B16.10 long pattern. 3. Stainless Steel va l ves and Carbon Steel va l ves have raised face flanges, but are also available with flat faced flanges. Bronze va l ves have flat face flanges only. 4. D rawings are for illustration purposes only. Consult PBM prior to any fabrication or installation wo r k. 5. A gear operator is recommended for va l ves 6" and larger. Consult PBM. 6. Dimensions are for ANSI 150# Class va l ves. Consult PBM for 300# Class. F D B G A

AN Series Actuated Size 1/2" DN 15 3/4" DN 20 1 DN 25 1-1/2" DN 40 2" DN 50 3" DN 80 4" DN 100 6" DN 150 8" DN 200 Industrial Valves RTF OR UHMWP SAT MATRIAL Actuator A B C D psig barg inches mm inches mm inches mm inches mm inches Double Acting 60, 80 4.1/5.5 5.5 139 2.8 71 5.8 148 1.61 41 1/8 Spring Return 60, 80 4.1/5.5 8.2 207 3.7 94 6.9 176 2.1 53 1/8 Double Acting 60, 80 4.1/5.5 5.5 139 2.8 71 5.9 151 1.61 41 1/8 Spring Return 60, 80 4.1/5.5 8.2 207 3.7 95 7.0 178 2.1 53 1/8 Double Acting 60, 80 4.1/5.5 5.5 139 2.8 71 7.2 182 1.61 41 1/8 Spring Return 80 5.5 8.2 207 3.7 95 8.3 210 2.1 53 1/8 Spring Return 60 4.1 9.4 238 4.2 106 8.7 221 2.3 58 1/8 Double Acting 60, 80 4.1/5.5 8.2 207 3.7 95 8.4 214 2.1 53 1/8 Spring Return 80 5.5 10.7 272 4.8 123 9.4 238 2.7 68 1/4 Spring Return 60 4.1 12.9 328 5.4 137 10.6 268 2.9 73 1/4 Double Acting 60, 80 4.1/5.5 8.2 207 3.7 95 8.7 222 2.1 53 1/8 Spring Return 80 5.5 10.7 272 4.8 123 9.7 246 2.7 68 1/4 Spring Return 60 4.1 12.9 328 5.4 137 10.9 276 2.9 73 1/4 Double Acting 60, 80 4.1/5.5 12.9 328 5.4 137 13.4 341 2.9 73 1/4 Spring Return 80 5.5 14.4 366 5.8 148 13.9 353 3.2 80 1/4 Spring Return 60 4.1 16.9 428 6.5 164 14.8 376 3.4 87 1/4 Double Acting 80 5.5 12.9 328 5.4 137 16.4 418 2.9 73 1/4 Double Acting 60 4.1 14.4 366 5.8 148 16.9 430 3.2 80 1/4 Spring Return 80 5.5 20.6 522 7.4 187 18.3 464 3.9 100 1/4 Spring Return 60 4.1 22.6 575 8.6 218 20.3 515 4.3 109 1/4 Double Acting 60, 80 4.1/5.5 20.6 522 7.4 187 20.2 514 3.9 100 1/4 Spring Return 80 5.5 22.6 575 8.6 218 22.3 565 4.3 109 1/4 Spring Return 60 4.1 26.5 672 11.4 290 25.9 657 5.7 145 1/4 Double Acting 80 5.5 26.5 672 11.4 290 28.5 725 5.7 145 1/4 Spring Return 60 CF CF CF CF CF CF CF CF CF CF Spring Return 60, 80 5.5 26.5 672 11.4 290 28.5 725 5.7 145 1/4 1 B A D C

Industrial Valves F-Series 5 Female NPT (Q-), Socket Weld (U-), Butt Weld for Sched. 40 (B-), Butt Weld for Sched. 40 (B-) 150# Flange () Size Code Units 1/2" DN 15 3/4" DN 20 1" DN 25 1-1/2" DN 40 2" DN 50 3" DN 80 4" DN 100 6" NOT S: C D G H K L Port Dia. 1 Q- U- A B D F G Face to Fa c e C L to Fa c e CL t o B o t t o m B- Q- B- B - D - D- U- D- Q-, U- CL t o To p o f H a n d l e H a n d l e Length from C L * For pad thickness requirements greater than those listed, consult PBM. 1. Full Po r t 2. Gear Operator recommended. 3. CF = Consult Fa c t o r y 4. Consult factory for approximate weight of 6" va l ves with Butt Weld for Sched. 40 (B-) end fitting. 5. Male NPT, Solder Joint, Sil-Braze, Camlock, and Grooved end fittings are also ava i l a b l e. 6. B- dimensions shown meet Schedule 40. nd fittings are also available to meet Schedule 10s or Schedule 5s. 7. 1/2" through 3" have 4 bolts. 4" through 8" va l ves have 8 bolts. 8. Flange holes straddle the center line, except for the 1-1/2" size. 9. D rawings are for illustration purposes only. Consult PBM prior to any fabrication or installation. 1 0. When using optional cylindrical radius pads, pocket area may increase. Consult PBM if reduced pocket area is desired. Note reduced pocket may decrease va l ve pressure rating. Butt Weld Length Pad Pad Dia. Thickness* Approx. Weight inches.5 2.8 4.0 4.0 1.56 2.8 2.8.98 2.68 4.2 1.5 2.8 0.28 2 lbs. 3 lbs. mm 13 72 102 102 40 70 70 23 67 105 38 70 7.1.9 kg. 1.4 kg. inches.8 3.1 4.1 4.2 1.72 2.8 2.9 1.0 2.8 4.2 1.5 3.0 0.31 2.5 lbs. 4 lbs. mm 19 78 104 107 44 70 73 25 71 105 38 70 7.1 1.1 kg. 1.8 kg. inches 1.0 3.8 4.7 5.0 2.1 3.0 3.3 1.33 3.1 5.1 1.5 3.8 0.32 5 lbs. 7 lbs. mm 25 98 120 126 54 76 83 34 78 129 38 95 8.1 2.3 kg. 3.2 kg. inches 1.5 5.1 6.1 6.3 2.8 3.8 4.0 1.78 4.4 8.7 1.5 5.5 0.46 13 lbs. 16 lbs. mm 38 129 154 161 70 95 102 45 111 221 38 140 11.7 5.9 kg. 7.3 kg. inches 2.0 5.7 6.7 7.6 3.0 4.0 4.9 2.2 4.7 8.7 1.75 6.5 0.49 19 lbs. 25 lbs. mm 51 144 169 192 76 102 124 55 119 221 45 165 12.4 8.6 kg. 11.3 kg. inches 3.0 8.4 10.6 10.3 4.5 6.8 6.4 3.1 6.8 12.4 2.3 9.0 0.77 57 lbs. 68 lbs. mm 76 213 270 261 114 172 162 80 174 315 59 229 19.6 25.9 kg. 30.8 kg. inches 4.0 10.8 12.8 12.3 6.0 8.0 7.5 4.9 7.3 24.1 2.3 11.5 0.90 120 lbs. 133 lbs. mm 102 275 325 313 152 203 191 125 186 611 59 292 22.9 54.4 kg. 60.3 kg. DN 150 M mm 154 452 427 279 254 182 Note 2 CF 95 432 31.2 CF CF inches 6.0 17.8 16.8 11.0 10.0 7.2 Note 2 CF 3.8 17.0 1.23 CF CF I F B-, Q- U- G H D A B Female NPT Q- Socket Weld U- Butt Weld B- D- 150# Flange

F-Series 5 Actuated Industrial Valves Size 1/2" DN 15 3/4" DN 20 1" DN 25 1-1/2" DN 40 2" DN 50 3" DN 80 4" DN 100 6" DN 150 TFM OR VTF SAT MATRIAL Actuator Type Air Supply A B C D F p s i g b a r g inches mm inches mm inches mm inches mm inches inches mm Double Acting 60, 80 4. 1 / 5. 5 5.5 139 2.8 71 5.4 136 1.61 41 1/8 0.09 2.3 Spring Return 80 5. 5 5.5 139 2.8 71 5.4 136 1.61 41 1/8 0.09 2.3 Spring Return 60 4. 1 6.4 162 3.2 81 5.8 147 1.77 45 1/8-0.13-3.3 Double Acting 60, 80 4. 1 / 5. 5 5.5 139 2.8 71 5.5 140 1.61 41 1/8 0.17 4.3 Spring Return 60, 80 4. 1 / 5. 5 6.4 162 3.2 81 6.0 151 1.77 46 1/8-0.05-1. 27 Double Acting 60, 80 4. 1 / 5. 5 5.5 139 2.8 71 6.2 156 1.61 41 1/8 0.53 13.5 Spring Return 60, 80 4. 1 / 5. 5 8.2 207 3.7 95 7.3 184 2.1 53 1/8 0.06 1.5 Double Acting 80 5. 5 6.4 162 3.2 81 7.9 200 1.77 45 1/8 0.92 23.4 Double Acting 60 4. 1 8.2 207 3.7 95 8.6 217 2.1 53 1/8 0.67 17.0 Spring Return 60, 80 4. 1 / 5. 5 10.7 272 4.8 123 9.5 241 2.7 68 1/4 0.15 3.8 Double Acting 60, 80 4. 1 / 5. 5 8.2 207 3.7 95 8.9 225 2.1 53 1/8 1.01 25.7 Spring Return 80 5. 5 10.7 272 4.8 123 9.8 249 2.7 68 1/4 0.49 12.5 Spring Return 60 4. 1 12.9 328 5.4 137 11.0 279 2.9 73 1/4 0.14 3.6 Double Acting 60, 80 4. 1 / 5. 5 12.9 328 5.4 137 13.0 330 2.9 73 1/4 1.36 34.5 Spring Return 80 5. 5 14.4 366 5.8 148 13.5 342 3.2 80 1/4 1.20 30.5 Spring Return 60 4. 1 16.9 428 6.5 164 14.4 364 3.4 87 1/4 0.85 22 Double Acting 60, 80 4. 1 / 5. 5 16.9 428 6.5 164 14.4 364 3.4 87 1/4 1.78 45 Spring Return 60, 80 4. 1 / 5. 5 20.6 522 7.4 187 17.0 431 3.9 100 1/4 1.38 35.1 Double Acting 60, 80 4. 1 / 5. 5 22.6 575 8.6 218 22.6 574 4.3 109 1/4 2.51 63.8 Spring Return 80 5. 5 22.6 575 8.6 218 22.6 574 4.3 109 1/4 2.51 63.8 Spring Return 60 4. 1 26.5 672 11.4 290 26.2 666 5.7 145 1/4 1.09 27.7 2 B F D A C

Industrial Valves AF-Series 1 Size Units Port B C D H I Face-to-Face CL to nd Q-, B-, U- Q-, B-, U- Pad Diameter Pad Thickness 2 1 DN 25 1-1/2 DN 40 2 DN 50 3 DN 80 4 DN 100 6 DN 150 8 DN 200 i n ch e s 1. 0 3.6 4. 1 1. 9 2.5 3.7.31 m m 25 91 104 48 64 94 7.9 i n ch e s 1. 5 5.0 5.5 2.7 3.3 5.5.56 m m 38 127 140 69 84 139.7 14.2 i n ch e s 2. 0 5.5 6.2 2.9 3.5 7.0.69 m m 51 140 158 74 89 177.8 17.5 inches 2.8 8.4 9.2 4.3 5.1 10.75 mm 70 213 234 109 130 254. 19.1 inches 3.5 9.5 10. 5 5.2 6.2 11.5.75 mm 89 241 267 132 158 292 19.1 inches 5.3 12. 1 * 15.6 6.6* 10.1 15.75 mm 133 307 396 168 257 381 19.1 inches 8 N / A 18 N / A 9.8 18.5 1.25 mm 2 0 0 N / A 460 N / A 250 470 32 *Buttweld end; Q and U not available in 6 size. 1, 1-1/2, & 8 = 10º 2, 3, 4, & 6 = 15º < degrees H I C D Q- = Female NPT Outlet U- = Socket Weld Outlet = 150# ANSI Flange Outlet

AF-Series 1 Actuated Size 1" DN 25 1-1/2" DN 40 2" DN 50 3" DN 80 4" DN 100 6" DN 150 RTF or UHMWP Seats Industrial Valves NPT Air Air supply Port A B C D Actuator Type Inlet psig barg inches mm inches mm inches mm inches mm inches mm inches Double Acting 80 5.5 5.5 139 2.8 71 1.12 28 6.2 158 1/8 Double Acting 60 4.1 6.4 162 3.2 81 0.93 24 6.7 169 1/8 1.00 25.4 Spring Return 80 5.5 8.2 207 3.7 95 0.73 19 7.3 186 1/8 Spring Return 60 4.1 9.4 238 4.2 106 0.55 14 7.8 197 1/8 Double Acting 60, 80 4.1, 5.5 8.2 207 3.7 95 1.55 39 8.4 212 1/8 Spring Return 80 5.5 1.50 38.1 10.7 272 4.8 123 1.10 28 9.3 237 1/4 Spring Return 60 4.1 12.9 328 5.4 137 0.84 21 10.5 267 1/4 Double Acting 60, 80 4.1, 5.5 8.2 207 3.7 95 2.5 63 8.5 216 1/8 Spring Return 80 5.5 2.00 50. 8 10.7 272 4.8 123 2.1 53 9.5 240 1/4 Spring Return 60 4.1 12.9 328 5.4 137 1.86 47 10.7 271 1/4 Double Acting 60, 80 4.1, 5.5 12.9 328 5.4 137 3.9 100 13.2 334 1/4 Spring Return 80 5.5 2.75 69.9 14.4 367 5.8 148 3.8 98 13.6 345 1/4 Spring Return 60 4.1 16.9 430 6.5 164 3.7 95 14.5 367 1/4 Double Acting 60, 80 4.1, 5.5 12.9 328 5.4 137 4.3 109 13.6 346 1/4 Spring Return 60 4.1 3.50 88.9 16.9 430 6.5 164 4.1 104 24.9 633 1/4 Spring Return 80 5.5 20.6 522 7.4 187 3.7 94 15.4 391 1/4 Double Acting 60, 80 4.1, 5.5 20.6 522 7.4 187 5.9 150 18.9 481 1/4 Spring Return 80 5.5 5.25 133.4 22.6 575 8.6 218 4.6 117 20.9 530 1/4 Spring Return 60 4.1 26.5 672 11.4 290 3.3 83 24.4 619 1/4 2 B A C D

Industrial Valves D-Series 5 Female NPT (Q-), Socket weld (U-), butt Weld for Schedule 40 (B-), 150# Flange () 4 Size 1 / 2 " DN 15 3 / 4 " DN 20 1 " DN 25 1-1 / 2 " DN 40 2 " DN 50 3 " DN 80 Size Code C D G H K U n i t s Po r t D i a. Q- U- A B C D G Face-to-Face B- D- Q- U- CL to Face B- D- H a n d l e L e n g t h f rom C L CL to Top of Handle CL to Bottom ntry Q- U- B- D- Length Dia. nd Fitting B- U- D- Length Length Dia. Approximate Weight Q-, U- B-, D- i n ch e s 0. 5 0 3. 1 5. 5 5. 5 1. 6 2. 8 2. 8 4. 2 2. 6 1. 6 2. 8 2. 8 0. 5 1. 5 3. 5 2 lbs. 5.2 lbs. m m 1 2. 7 7 9 1 4 0 1 4 0 4 1 7 1 7 1. 1 0 7 6 6 4 1 7 1 7 1 1 3 3 8 8 9.9 kg. 2.4 kg. i n ch e s 0. 7 5 3. 4 5. 5 5. 8 1. 7 2. 8 2. 9 4. 2 2. 8 1. 7 2. 8 2. 9 0. 6 1. 5 4. 0 2.5 lbs. 7 lbs. m m 1 9. 1 8 6 1 4 0 1 4 7 4 3 7 1 7 4 1 0 7 7 1 4 3 7 1 7 4 1 5 3 8 1 0 2 1.1 kg. 3.2 kg. i n ch e s 1. 0 4. 3 6. 0 6. 5 2. 1 3. 0 3. 3 5. 1 3. 0 2. 1 3. 0 3. 3 0. 5 1. 5 4. 3 5 lbs. 11 lbs. m m 2 5 1 0 9 1 5 2 1 6 5 5 3 7 6 8 4 1 3 0 7 6 5 3 7 6 8 4 1 3 3 8 1 0 9 2.3 kg. 5.0 kg. i n ch e s 1. 5 5. 5 7. 5 8. 0 2. 8 3. 8 4. 0 8. 7 4. 1 2. 8 3. 8 4. 0 0. 5 1. 5 5. 0 11.5 lbs. 21.5 lbs. m m 3 8 1 4 0 1 9 1 2 0 3 7 1 9 7 1 0 2 2 2 1 1 0 4 7 1 9 7 1 0 2 1 3 3 8 1 2 7 5.2 kg. 9.8 kg. i n ch e s 2. 0 6. 0 8. 0 9. 8 3. 0 4. 0 4. 9 8. 7 4. 4 3. 0 4. 0 4. 9 0. 7 1. 8 6. 0 16.5 lbs. 33 lbs. m m 5 1 1 5 2 2 0 3 2 4 9 7 6 1 0 2 1 2 5 2 2 1 1 1 2 7 6 1 0 2 1 2 5 1 8 4 6 1 5 2 7.5 kg. 15.0 kg. i n ch e s 3. 0 9. 0 1 3. 5 1 2. 9 4. 5 6. 8 6. 4 1 2. 4 6. 8 4. 5 6. 8 6. 4 0. 7 2. 3 7. 5 50 lbs. 80 lbs. m m 7 6 2 2 9 3 4 3 3 2 8 1 1 4 1 7 3 1 6 3 3 1 5 1 7 3 1 1 4 1 7 3 1 6 3 1 8 5 8 1 9 1 22.7 kg. 36.3 kg. 4 " i n ch e s 4. 0 12. 0 16. 0 15. 0 6. 0 8. 0 7. 5 24. 4 7. 3 6. 0 8. 0 7. 5 0. 8 2. 3 9. 0 123 lbs. 155 lbs. DN 100 L m m 102 305 406 381 152 203 191 620 185 152 203 191 20 58 229 55.8 kg. 70.3 kg. 6 " DN 150 M i n ch e s 6. 0 C F 2 2. 0 2 0. 0 C F 1 1. 0 1 0. 0 Note 1 Note 1 9. 0 1 1. 0 1 0. 0 C F 3. 8 1 1. 0 C F C F m m 1 5 2. 4 C F 5 5 9 5 0 8 C F 2 7 9 2 5 4 Note 1 Note 1 2 2 9 2 7 9 2 5 4 C F 9 7 2 7 9 C F C F N o t e s : 1. Gear operator is recommended. 2. Other end fittings are also available. See page 16 and 18. 3. Other flanged end fittings are available upon special request. 4. Butt Weld ends are also available in Schedule 10s & Schedule 5s. 5. 1/2" 3" size va l ves have 4 bolts. 4" and 6" sizes have 8 bolts. 6. D rawings are for illustration purposes only. 7. Using a welded connection on the common port of a DP va l ve may complicate maintenance. Provisions must be made to allow removal of end fittings and body from the line. PBM recommends Female NPT (Q-) or flanged end fittings for common port connection for ease of va l ve maintenance. Refer to Page 12 for Flow Pattern Options C D G B A Female NPT Q- G Socket Weld U- G Butt Weld B- D- 150# Flange B

D-Series 5 Actuated Industrial Valves Size 1/2" DN 15 3/4" DN 20 1" DN 25 1-1/2" DN 40 2" DN 50 3" DN 80 4" DN 100 6" DN 150 TFM or VTF SAT MATRIAL Actuator Type Air Supply A B C D psig barg inches mm inches mm inches mm inches mm inches Double Acting 60, 80 4.1, 5.5 5.5 139 2.8 71 5.4 136 1.61 41 1/8 Spring Return 80 5. 5 5.5 139 2.8 71 5.4 136 1.61 41 1/8 Spring Return 60 4.1 6.4 162 3.2 81 5.8 147 1.77 45 1/8 Double Acting 60, 80 4.1, 5.5 5.4 139 2.8 71 5.5 140 1.61 41 1/8 Spring Return 60, 80 4.1, 5.5 6.4 162 3.2 81 6.0 151 1.77 45 1/8 Double Acting 60, 80 4.1, 5.5 5.5 139 2.8 71 6.2 157 1.61 41 1/8 Spring Return 60, 80 4.1, 5.5 8.2 207 3.7 95 7.3 184 2.1 53 1/8 Double Acting 80 5. 5 6.4 162 3.2 81 7.9 201 1.77 45 1/8 Double Acting 60 4.1 8.2 207 3.7 95 8.6 217 2.1 53 1/8 Spring Return 60, 80 4.1, 5.5 10.7 271 4.8 123 9.5 242 2.7 68 1/4 Double Acting 80 5. 5 8.2 207 3.7 95 8.9 225 2.1 53 1/8 Double Acting 60 4.1 8.2 207 3.7 95 8.9 225 2.1 53 1/8 Spring Return 80 5. 5 10.7 271 4.8 123 9.8 249 2.7 68 1/4 Spring Return 60 4.1 12.9 328 5.4 137 11.0 279 2.9 73 1/4 Double Acting 60, 80 4.1, 5.5 12.9 328 5.4 137 13.0 330 2.9 73 1/4 Spring Return 80 5. 5 14.4 366 5.8 148 13.5 342 3.2 80 1/4 Spring Return 60 4.1 16.9 428 6.5 164 14.4 364 3.4 87 1/4 Double Acting 60, 80 4.1, 5.5 16.9 428 6.5 164 16.5 419 3.4 87 1/4 Spring Return 60, 80 4.1, 5.5 20.6 522 7.4 187 17.0 431 3.9 100 1/4 Double Acting 60, 80 4.1, 5.5 22.6 575 8.6 218 23.0 574 4.3 109 1/4 Spring Return 80 5. 5 22.6 575 8.6 218 23.0 574 4.3 109 1/4 Spring Return 60 4.1 26.5 672 11.4 290 26.2 666 5.7 145 1/4 2 B A D C

6 Industrial Valves M-Series 4 A B C 1 D 1 C 2 D 2 F G 1 G 2 H I Size 1 / 2 " DN 15 3 / 4 " DN 20 1 " DN 25 1-1 / 4 " DN 32 1-1 / 2 " DN 40 2 " DN 50 3 DN 80 4 DN 100 6 DN 150 Size Code Units Port Dia. C D F G H K L Face to Fa c e CL to Fa c e Face to Fa c e CL to Fa c e Q/U- B- Q/U- B- Q/U- B- Q/U- B- H a n d l e L e n g t h f rom CL CL to Top of Handle CL to Bottom Side ntry CL to Bottom Bottom ntry U - D i a. Dia. A p p rox. Weight S/S i n ch e s. 50 4. 5 C F 2. 3 C F 4. 5 C F 2. 3 C F 6. 1 2. 8 1. 5 C F. 9 3. 5 7 lbs. m m 13 114 C F 58 C F 114 C F 58 C F 155 71 38 C F 23 89 3.2 kg. i n ch e s. 75 4. 5 C F 2. 3 C F 4. 5 C F 2. 3 C F 6. 1 2. 8 1. 5 C F 1. 0 3. 9 7 lbs. m m 19 114 C F 58 C F 114 C F 58 C F 155 71 38 C F 25 99 3.2 kg. i n ch e s 1. 0 4. 7 7. 3 2. 3 3. 6 4. 7 5. 7 2. 3 3. 6 8. 1 5. 0 1. 6 2. 3 1. 3 4. 3 12 lbs. m m 25 119 185 58 91 119 145 58 91 206 127 41 58 33 109 5.4 kg. i n ch e s 1. 0 4. 7 C F 2. 3 C F 4. 7 C F 2. 3 C F 8. 1 5. 0 1. 6 2. 4 1. 7 4. 6 12 lbs. m m 25 119 C F 58 C F 119 C F 58 C F 206 127 41 61 43 117 5.4 kg. i n ch e s 1. 5 6. 6 10. 6 3. 3 5. 3 6. 6 8. 6 3. 3 5. 3 12. 1 5. 3 2. 3 3. 3 1. 9 5. 0 31 lbs. m m 38 168 269 84 135 168 218 84 135 307 135 58 84 48 127 14.1 kg. i n ch e s 2. 0 7. 8 11. 9 3. 9 6. 0 7. 6 9. 7 3. 9 6. 0 12. 1 5. 8 2. 6 3. 9 2. 4 6. 0 47 lbs. m m 51 198 302 99 152 193 246 99 152 307 147 66 99 61 152 21.3 kg. i n ch e s 3. 0 11. 7 16. 5 5. 8 8. 2 11. 1 13. 5 5. 8 8. 2 Consult PBM 3. 9 5. 8 3. 5 7. 5 133 lbs. m m 76 297 419 147 208 282 343 147 208 99 147 89 191 60.3 kg. i n ch e s 4. 0 15. 4 19. 3 7. 7 9. 6 14. 2 16. 2 7. 7 9. 6 Consult PBM 4. 9 7. 7 4. 6 9. 0 254 lbs. m m 102 391 490 196 244 361 412 196 244 125 196 117 229 115. 2 k g. M m m 152 419 546 216 305 506 610 254 305 241 254 170 279 181.4 kg. i n ch e s 6. 0 16. 5 21. 5 8. 5 12. 0 19. 9 24. 0 10. 0 12. 0 Consult PBM 9. 5 10. 0 6. 7 11. 0 400 lbs. -NOT S: 1. Using a welded connection for more than one end fitting on an MP Series va l ve may complicate maintenance. Provisions must be made to allow removal of end fittings and body from the line. 2. C avity fillers in 1/2" 4" sizes are installed from the top. Cavity fillers in 6" size are installed from the sides. 3. 1-1/4" and double angle port are not full-port design. 4. A gear operator is recommended for 3", 4", and 6" va l ves. Consult PBM. 5. D rawings are for illustration purposes only. Consult PBM prior to any fabrication or installation wo r k. 6. Approximate weights are for 3-way, side entry, angle port MP Series 4 va l ves, with female NPT end fittings. 7. Q and U ends not available in 6 size. Refer to Page 12-13 for Flow Pattern Options F B G2 G1 I H D2 C2 Female NPT Q- C1 D1 150# Flange Butt Weld B- Socket Weld U-

M-Series 4 Actuated Size 1/2" DN 15 3/4" DN 20 1" DN 25 1-1/4" DN 32 1-1/2" DN 40 2" DN 50 3" DN 80 4" DN 100 6" DN 150 Actuator Type VTF OR TFM SAT MATRIAL Industrial Valves Air supply A B C D psig barg inches mm inches mm inches mm inches mm inches Double Acting 80 5.5 5.5 139 2.8 71.1 6.8 171 1.61 41 1/8 Double Acting 60 4.1 6.4 162 3.2 80.5 7.2 182 1.77 45 1/8 Spring Return 80 5.5 8.2 207 3.7 94.5 7.8 199 2.1 53 1/8 Spring Return 60 4.1 9.4 238 4.2 105.9 8.3 210 2.3 58 1/8 Double Acting 80 5.5 5.5 139 2.8 71.1 6.7 171 1.61 41 1/8 Double Acting 60 4.1 6.4 162 3.2 80.5 7.2 183 1.77 45 1/8 Spring Return 80 5.5 8.2 207 3.7 94.5 7.8 199 2.1 53 1/8 Spring Return 60 4.1 9.4 238 4.2 106 8.3 210 2.3 58 1/8 Double Acting 60, 80 4.1, 5.5 8.2 207 3.7 94.5 8.7 220 2.1 53 1/8 Spring Return 80 5.5 10.7 272 4.8 123 9.6 244 2.7 68 1/4 Spring Return 60 4.1 12.9 328 5.4 137 10.8 274 2.9 73 1/4 Double Acting 60, 80 4.1, 5.5 8.2 207 3.7 94.5 8.7 220 2.1 53 1/8 Spring Return 80 5.5 10.7 272 4.8 123 9.6 244 2.7 68 1/4 Spring Return 60 4.1 12.9 328 5.4 137 10.8 274 2.9 73 1/4 Double Acting 60, 80 4.1, 5.5 12.9 328 5.4 137 12.1 308 2.9 73 1/4 Spring Return 80 5.5 14.4 366 5.8 148 12.6 320 3.2 80 1/4 Spring Return 60 4.1 16.9 428 6.5 164 15.2 387 3.4 87 1/4 Double Acting 60, 80 4.1, 5.5 12.9 328 5.4 137 12.5 318 2.9 73 1/4 Spring Return 80 5.5 14.4 366 5.8 148 13.0 330 3.2 80 1/4 Spring Return 60 4.1 16.9 428 6.5 164 15.6 397 3.4 87 1/4 Double Acting 80 5.5 12.9 328 5.4 137 15.7 399 2.9 73 1/4 Double Acting 60 4.1 14.4 366 5.8 148 16.2 411 3.2 80 1/4 Spring Return 80 5.5 20.6 522 7.4 187 19.3 490 3.9 100 1/4 Spring Return 60 4.1 22.6 575 8.6 218 21.6 548 4.3 109 1/4 Double Acting 60, 80 4.1, 5.5 22.6 575 8.6 218 22.7 576 4.3 109 1/4 Spring Return 80 5.5 22.6 575 8.6 218 22.7 576 4.3 109 1/4 Spring Return 60 4.1 26.5 672 11.4 290 26.9 684 5.7 145 1/4 Double Acting 80 5.5 22.6 575 8.6 218 23.7 602 4.3 109 1/4 Double Acting 60 4.1 22.6 575 8.6 218 23.7 602 4.3 109 1/4 Spring Return 80 5.5 26.5 672 11.4 290 28.0 711 5.7 145 1/4 Spring Return 60 4.1 26.5 672 11.4 290 28.0 711 5.7 145 1/4 2 B A D C

Industrial Valves M-Series 1 8 S i z e 1 / 2 " DN 15 3 / 4 " DN 20 1 " DN 25 1-1 / 4 " DN 32 1-1 / 2 " DN 40 2 " DN 50 3 " DN 80 4 " DN 100 N o t e s : S i z e C o d e C D F G H K L U n i t s B C 1 D 1 C 2 D 2 F G 1 G 2 H I Face to Fa c e A p p rox. CL to Fa c e Face to Fa c e CL to Fa c e CL to CL to Po r t H a n d l e CL to Bottom Bottom R - L - We i g h t L e n g t h Top of D i a. B ro n z e f rom C Side Bottom D i a. D i a. Q -/ S L - Q -/ S L - Q -/ S L - Q -/ S L - L Handle ntry ntry i n ch e s. 62 4. 0 C F 2. 0 C F 4. 0 C F 2. 0 C F 6. 1 2. 8 1. 5 C F. 9 3. 5 17 lbs. m m 16 102 C F 51 C F 102 C F 51 C F 155 71 38 C F 23 89 7.7 kg. i n ch e s. 75 4. 0 C F 2. 0 C F 4. 0 C F 2. 0 C F 6. 1 2. 8 1. 5 C F 1. 0 3. 9 17 lbs. m m 196 102 C F 51 C F 102 C F 51 C F 155 71 38 C F 25 99 7.7 kg. i n ch e s 1. 0 4. 7 7. 3 2. 3 3. 6 4. 5 5. 7 2. 4 3. 6 8. 1 5. 0 1. 6 2. 3 1. 3 4. 3 22 lbs. m m 25 119 185 58 91 114 145 61 91 206 127 41 58 33 109 10.0 kg. i n ch e s 1. 0 4. 8 C F 2. 4 C F 4. 5 C F 2. 4 C F 8. 1 5. 0 1. 6 2. 4 1. 7 4. 6 23 lbs. m m 25 122 C F 61 C F 114 C F 61 C F 206 127 41 61 43 117 10.4 kg. i n ch e s 1. 5 6. 6 10. 6 3. 3 5. 3 6. 0 8. 6 3. 3 5. 3 12. 1 5. 3 2. 3 3. 3 1. 9 5. 0 47 lbs. m m 38 168 269 84 135 152 218 84 135 307 135 58 84 48 127 21.3 kg. i n ch e s 2. 0 7. 8 11. 9 3. 9 6. 0 7. 6 9. 7 3. 9 5. 9 12. 1 5. 8 2. 6 3. 9 2. 4 6. 0 70 lbs. m m 51 198 302 99 152 193 246 99 150 307 147 66 99 61 152 31.8 kg. i n ch e s 2. 3 11. 0 14. 6 5. 5 7. 3 9. 6 11. 4 5. 5 7. 3 12. 1 6. 7 4. 1 5. 5 3. 5 7. 5 107 lbs. m m 57 279 371 140 185 244 290 140 185 307 170 104 140 89 191 48.5 kg. i n ch e s 3. 0 C F 17. 0 C F 8. 5 C F 14. 0 C F 8. 5 14. 1 8. 8 5. 6 C F C F 9. 0 235 lbs. m m 76 C F 432 C F 216 C F 356 C F 216 358 224 142 C F C F 229 107 kg. 1. Iron va l ves have raised face flanges. Bronze va l ves have flat face flanges. 2. D rawings are for illustration purposes only. Consult PBM prior to any fabrication or installation wo r k. 3. Using a brazed or soldered connection for more than one end fitting on an MP Series va l ve may complicate maintenance. Provisions must be made to allow removal of end fittings and body from line. 4. Approximate weights are estimated based on va l ves with 150# Flange end fittings. Refer to Page 12-13 for Flow Pattern Options F I H B G2 G1 D2 S- (Bronze Only) C2 Female NPT Q- C1 D1

M-Series 1 Actuated Industrial Valves Size 1/2" DN 15 3/4" DN 20 1" DN 25 1-1/4" DN 32 1-1/2" DN 40 2" DN 50 Actuator Type VTF OR TFM SAT MATRIAL Air Supply A B C D psig barg inches mm inches mm inches mm inches mm inches Double Acting 80 5.5 5.5 139 2.8 71 7.5 189 1.61 41 1/8 Double Acting 60 4.1 6.4 162 3.2 81 7.9 200 1.77 45 1/8 Spring Return 80 5.5 8.2 207 3.7 95 8.5 217 2.1 53 1/8 Spring Return 60 4.1 9.4 238 4.2 106 9.0 228 2.3 58 1/8 Double Acting 80 5.5 5.5 139 2.8 71 7.5 189 1.61 41 1/8 Double Acting 60 4.1 6.4 162 3.2 81 7.9 200 1.8 45 1/8 Spring Return 80 5.5 8.2 207 3.7 95 8.5 217 2.1 53 1/8 Spring Return 60 4.1 9. 238 4.2 106 9.0 228 2.3 58 1/8 Double Acting 60, 80 4.1, 5.5 8.2 207 3.7 95 9.5 241 2.1 53 1/8 Spring Return 80 5.5 10.7 272 4.8 123 10.5 265 2.7 68 1/4 Spring Return 60 4.1 12.9 328 5.4 137 11.6 295 2.9 73 1/4 Double Acting 60, 80 4.1, 5.5 8.2 207 3.7 95 9.5 241 2.1 53 1/8 Spring Return 80 5.5 10.7 272 4.8 123 10.5 265 2.7 68 1/4 Spring Return 60 4.1 12.9 328 5.4 137 11.6 295 2.9 73 1/4 Double Acting 80 5.5 12.9 328 5.4 137 13.3 338 2.9 73 1/4 Double Acting 60 4.1 12.9 328 5.4 137 13.3 338 2.9 73 1/8 Spring Return 80 5.5 14.4 366 5.8 148 13.8 350 3.2 80 1/4 Spring Return 60 4.1 16.9 428 6.5 164 15.2 387 3.4 87 1/4 Double Acting 60, 80 4.1, 5.5 12.9 328 5.4 137 13.5 344 2.9 73 1/4 Spring Return 80 5.5 14.4 366 5.8 148 14.0 356 3.2 80 1/4 Spring Return 60 4.1 16.9 428 6.5 164 15.6 397 3.4 87 1/4 3" Double Acting 60, 80 4.1, 5.5 12.9 328 5.4 137 13.9 353 2.9 73 1/4 DN 80 Spring Return 60, 80 4.1, 5.5 20.6 522 7.4 187 17.5 445 3.9 100 1/4 4" Double Acting 60, 80 4.1, 5.5 12.9 328 5.4 137 17.0 433 2.9 73 1/4 DN 100 Spring Return 60, 80 4.1, 5.5 20.6 522 7.4 187 20.6 524 3.9 100 1/4 2 B A D C

Industrial Valves Transmitter Isolation Valves Obtain accurate transmitter readings and replace leaky knife gate valves with PBM s Transmitter Isolation Valve. Ideal for Pulp & Paper and Chemical applications. 2-Way ball valve features minimal dead space and positive shut-off. Calibration Port, CIP Port, 150# Flange, and Locking Handle standard. 0 Sizes: 1", 2", 2-1/2", 3" Materials: 316 & 317L S/S Ti t a n i u m H a s t e l l oy O t h e r s Options: Milled Ball Flats Po l i s h i n g Tank Bottom Valve Transmitter 1 TIV Studs from Tank Pad to Valve Transmitter 3 150# Flange 5/8-11 x 2-1/4 LG. Hex Bolt or 3-1/4 LG. All Thread Stud for Transmitter to Valve 2-1/2 TIV 3 150# Flange Studs from Tank Pad to Valve Transmitter 5/8-11 x 2-1/4 LG. Hex Bolt or 3-1/4 LG. All Thread Stud for Transmitter to Valve

Instrument Valves Industrial Valves root valves gauge valves isolation valves drain valves Applications Isolation for: n Transmitter pressure measurement n Flush rings n Flow measurement n Pressure gauges n Orifice plates 3 Features Can be mounted on 2-1/8 centers asy 1/4-turn operation 1/2, 3/4 sizes, API 607 dition 5 qualified Class 2500# Manufactured from wrought or forged material Rod-out capability Variety of end connections Variety of body materials Variety of seat and seal materials Optional Ceramic Balls & Seats (Zirconia TTZ) Welded tamperproof body design Visual position indication Lockable handles available Unique applications welcome

Industrial Valves Fabflex Manifold Assemblies 2 Fabflex Manifolds are space-saving pipe and valve configurations designed to accommodate special industrial and sanitary applications. Can be shipped in lengths up to 18, with multiple manual and automated valves preinstalled. 100% testing before shipment ensures proper performance. Minimal dead space reduces areas where media could become trapped. Blank valve pads can be provided to accommodate future process expansion. Valve Sizes: 1/4" - 6" M a t e r i a l s : 316 & 316L S/S Carbon Steel H a s t e l l o y O p t i o n s : F i re - Te s t C I P / S I P Cavity Fillers A c t u a t i o n S t e a m Polishing & l e c t ro p o l i s h i n g

Industrial Valves Control Valves Sampling Valves Use PBM s 2-Way Control Valves in industrial and sanitary throttling or shearing applications to accurately control the flow of liquids or thick media. These valves feature characterized balls with various port shapes, including "V." Manual valve standard. S i z e s : 1/2" - 6" M a t e r i a l s : 316 & 316L S/S H a s t e l l o y O t h e rs O p t i o n s : A c t u a t i o n 30, 45, 60 V Angles S l o t t e d Locking Handle Polishing & l e c t ro p o l i s h i n g 3 Sample process media quickly and easily with PBM s Sampling Valve. Special pad design minimizes dead space. asy CIP with Purge Ports and Milled Ball Flats ensures reliable samples. Valve can be shipped pre-mounted to piping for easy installation. Ideal for heavy duty and sanitary applications. Manual valves standard. S i z e s : 1/2" - 2" M a t e r i a l s : 316 & 316L S/S H a s t e l l o y T i t a n i u m O t h e rs O p t i o n s : A c t u a t i o n S t e a m Po l i s h i n g Rising Stem Sampling Valve 316L S/S Swickle or Hose Barb Outlet 1/4 Bore Diameter L a rge Nylon Knob T h readed Inlet (1/4, 3/8 ) Autoclavable or To rc h a b l e Replaceable PDM O-Ring and T F M S e a t Po l i s h i n g

Automation and Controls Die cast aluminu m end cap s, p o lyester p owder coat e d N i cke l - p l at e d Steel pinion S t a n d a rd Vi s u a l Po s i t i o n I n d i c at o r B o dy manu fa c t u red from ex t ruded aluminum UNI 6060, H a rd coat anodize d Piston guide 4 N e s t e d spring sets A s s e m bly screw Stainless Steel Operating Pressure Range - 40 psig to 120 psig (2.8 barg to 8 barg) Temperature Range: -4ºF to 185ºF (-20ºC to 85ºC) Rotation Adjustment: + or - 5º Namur Pinion and Solenoid Valve Mounting Bottom of Pinion according to ISO 5211 - DIN 3337 Actuator Model Spring Set Piston guide S e a l s NBR Standard Pistons made from die cast aluminu m Air Pressure at Actuator Approximate 60 psig 4.1 barg 80 psig 5.5 barg Actuator Model Weight Constant Torque Output in-lbs. N-m in-lbs. N-m lbs. kg. PAVBL453D--0052 133 15 179 20 2.3 1.0 PAVBL453D--0063 238 27 321 36 3.3 1.5 PAVBL453D--0075 435 49 586 66 5.5 2.5 PAVBL453D--0085 629 71 851 96 7 3 PAVBL453D--0100 991 112 1,336 151 11 5 PAVBL453D--0115 1,640 185 2,210 250 18 8 PAVBL453D--0125 2,157 244 2,906 328 22 10 PAVBL453D--0140 3,013 340 4,018 454 34 15 PAVBL453D--0160 4,394 497 5,859 662 43 20 PAVBL453D--0200 8,239 931 10,981 1,241 71 32 PAVBL453D--0270 19,097 2,158 25,469 2,878 154 70 Air Pressure at Actuator Spring Torque 60 psig/4.1 barg 80 psig/5.5 barg Output Torque Output from Pressure Start Start nd nd Start Start nd nd Start Start nd nd Approximate Weight in-lbs. N-m in-lbs. N-m in-lbs. N-m in-lbs. N-m in-lbs. N-m in-lbs. N-m lbs. kg. PAVBL253S- -0052 03 66 7.5 38 4.3 80 9.0 47 5.3 N/A N/A N/A N/A 2.7 1.2 PAVBL453S- -0052 05 88 10 60 7 N/A N/A N/A N/A 101 11.4 55 6 2.7 1.2 PAVBL253S- -0063 03 128 15 71 8 149 17 79 9 N/A N/A N/A N/A 4.0 2 PAVBL453S- -0063 05 196 22 111 13 N/A N/A N/A N/A 193 22 95 11 4.0 2 PAVBL253S- -0075 03 234 26 125 14 275 31 137 16 N/A N/A N/A N/A 6.9 3 PAVBL453S- -0075 05 358 40 193 22 N/A N / A N/A N/A 354 40 157 18 6.9 3 PAVBL253S- -0085 03 307 35 183 21 387 44 211 24 N/A N/A N/A N/A 9.4 4 PAVBL453S- -0085 05 456 52 273 31 N/A N/A N/A N/A 503 57 257 29 9.4 4 PAVBL253S- -0100 03 495 56 279 32 628 71.0 329 37 N/A N/A N/A N/A 14.4 7 PAVBL453S- -0100 05 733 83 417 47 N/A N / A N/A N/A 802 91 378 43 14.4 7 PAVBL253S- -0115 03 786 89 442 50 1,044 118 541 61 N/A N/A N/A N/A 24 11 PAVBL453S- -0115 05 1,176 133 657 74 N/A N/A N/A N/A 1,352 153 637 72 24 11 PAVBL253S- -0125 03 969 110 530 60 1,351 153 640 72 N/A N/A N/A N/A 27 12 PAVBL453S- -0125 05 1,412 160 779 88 N/A N/A N/A N/A 1,762 199 789 89 27 12 PAVBL453S- -0140 03 1,617 183 853 96 1,910 216 856 97 N/A N/A N/A N/A 45 21 PAVBL453S- -0140 05 2,251 254 1,200 136 N/A N/A N/A N/A 2,481 280 1,017 115 45 21 PAVBL253S- -0160 04 2,443 276 1,522 172 2,447 277 1,350 153 N/A N/A N/A N/A 65 30 PAVBL453S- -0160 05 2,860 323 1,917 217 N/A N/A N/A N/A 3,452 390 2,240 253 65 30 PAVBL253S- -0200 04 4,040 457 2,686 304 4,788 541 3,080 348 N/A N/A N/A N/A 111 50 PAVBL453S- -0200 06 5,900 667 4,009 453 N/A N/A N/A N/A 5,893 666 3,539 400 111 50 PAVBL253S- -0270 05 10,788 1, 219 6,915 781 11,495 1, 299 6,884 778 N/A N/A N/A N/A 193 88 PAVBL453S- -0270 08 14,400 1, 627 9,230 1,043 N/A N/A N/A N/A 15,360 1,735 9,220 1,042 193 88

Automation and Controls Postioners lectric Actuators 4-20 ma 3-15 psi Nema 4, 7 Nema 4, 7 Features: Solenoids 3 Compact spool valve with threaded port direct mounts to actuator. All exhaust ports are pipeable, providing better protection against harsh environments. Standard manual override DIN, watertight and explosion-proof solenoids available Single and dual coil solenoid constructions Mountable in any position Position Indicators Options: Nema 4, 7 Mechanical Switches Proximity Fieldbus DeviceNet Visual Indication AS-i

PBM, Inc. United States Canada Australia Mexico Brazil Chile UA United Kingdom Germany Sweden Spain Belgium France Ireland Switzerland Austria The Netherlands India Taiwan China Thailand Singapore Visit PBM online at www.pbmvalve.com to find the PBM domestic or international representative near you. PBM, Inc. 1070 Sandy Hill Road, Irwin, PA 15642 Phone: 800.967.4PBM 724.863.0550 Fax: 724.864.9255 -mail: info@pbmvalve.com Web: www.pbmvalve.com LT- 31 5/08