INSTLLTION INSTRUCTIONS FOR PRT 99-74 PPLICTIONS Nissan Sentra 007-008 99-74 KIT FETURES DIN Radio Provision with Pocket Double DIN Radio Provision Stacked ISO Mount Units Provision KIT COMPONENTS ) Radio Housing ) Radio Housing Trimplate C) Radio Housing rackets D) Double DIN Trim Plate E) () Carriage olts F) () Nuts C D E F WIRING ND NTENN CONNECTIONS (Sold Separately) Harness: 70-755 - Nissan harness 007-up NIRD-0 - Nissan display and luetooth retention harness 007-08 ntenna dapter: 40-NI - Nissan antenna adapter 007-up TOOLS REQUIRED: Small Flat lade Screwdriver/ Panel Removal Tool Phillips Screwdriver Hook Tool Socket Set -800--09 www.metraonline.com COPYRIGHT 004-009 METR ELECTRONICS CORPORTION
99-74 Dash Disassembly TLE OF CONTENTS - Nissan Sentra 007-008..........................., Kit ssembly - Kit Preparation (For DIN radio with pocket only)................. - DIN Radio Provision with Pocket............................. 4 - Double DIN Radio Provision................................ 5 - Stacked ISO Mount Units Provision........................... 6 Final ssembly...........................................7 *Note: Refer also to the instructions included with the aftermarket radio. KNOWLEDGE IS POWER Enhance your installation and fabrication skills by enrolling in the most recognized and respected mobile electronics school in our industry. Log onto www.installerinstitute.com or call 800-54-678 for more information and take steps toward a better tomorrow.
SEEK POWER TUNE PSS IRG 99-74 DSH DISSSEMLY NISSN SENTR 007-008 Disconnect the negative battery terminal to prevent an accidental short circuit. Push down on the collar below the shift knob to unclip. Using a small screwdriver or hook tool remove the spring clip to release and remove the shift knob. (Figure ) Unclip and remove shifter trim panel around shifter. (Figure ) 4 5 Unclip and remove the a/c control panel. (Figure C) Remove () Phillips screws securing the bottom of the radio trim panel. (Figure D) D C POWER SEEK TUNE c LO HI LO c HI
SEEK POWER TUNE SEEK POWER TUNE 99-74 DSH DISSSEMLY NISSN SENTR 007-008 6 Unclip and remove the trim panel at the top of the radio trim panel. (Figure E) E 7 8 Remove () Phillips screws securing the top of the radio trim panel. (Figure F) Unplug and remove radio/trim panel assembly. (Figure G) POWER 9 Remove (4) Phillips screws securing the radio brackets to the trim panel and remove the trim panel. F 0 Remove (6) Phillips screws ( per side) securing the factory brackets to the radio/display assembly. (Retain the factory brackets and display for possible use during kit assembly.) Continue to kit assembly. G
99-74 KIT SSEMLY KIT PREPRTION (FOR DIN RDIO WITH POCKET ONLY) *Note: Refer also to the instructions included with the aftermarket radio. ttach the () radio housing brackets to the radio housing using the supplied () carriage bolts and nuts. (Figure ) Secure the display* into the assembled radio housing/bracket assembly using the factory hardware. (Figure ) *NOTE: Display can be replaced with Metra s Pocket, Part number 88-00- 74 sold separately. Continue to final assembly.
99-74 KIT SSEMLY DIN RDIO PROVISION WITH POCKET *Note: Refer also to the instructions included with the aftermarket radio. Slide the DIN cage into the Radio Housing and secure by bending the metal locking outward. (Figure ) Slide the aftermarket radio into the cage until it snaps into place. (Figure ) ttach the radio housing trim plate supplied with the kit. (Figure ) NOTE: Display can be replaced with Metra s Pocket, Part number 88-00- 74 sold separately. Continue to final assembly. 4
99-74 KIT SSEMLY DOULE DIN RDIO PROVISION *Note: Refer also to the instructions included with the aftermarket radio. Re-Secure the display* to the factory brackets using the factory hardware. (Figure ) Slide the Double DIN radio into the factory brackets and secure the unit to the brackets using the screws supplied with the radio. (Figure ) Place the Double DIN trim plate over the face of the aftermarket radio. (Figure ) *NOTE: Display can be replaced with Metra s Pocket, Part number 88-00- 74 sold separately. Continue to final assembly. 5
99-74 KIT SSEMLY STCKED ISO MOUNT UNITS PROVISION *Note: Refer also to the instructions included with the aftermarket radio. Re-Secure the display* to the factory brackets using the factory hardware. (Figure ) Slide the stacked ISO Mount units into the factory bracket/display assembly and secure the units to the assembly using the screws supplied with the units. (Figure ) Place the Double DIN trim plate over the face of the units. (Figure ) *NOTE: Display can be replaced with Metra s Pocket, Part number 88-00- 74 sold separately. Continue to final assembly. 6
99-74 FINL SSEMLY FINL SSEMLY C () Strip wire ends back /" ) Twist ends together C) Solder D) Tape D Locate the factory wiring harness in the dash. Metra recommends using the proper mating adapter and making connections as shown. (Isolate and individually tape off the ends of any unused wires to prevent electrical short circuit.) Re-connect the negative battery terminal and test the unit for proper operation. Reassemble radio and dash assemblies in reverse order of disassembly. FINL WIRING CONNECTIONS Make wiring connections using the EI color code chart shown below and the instructions included with the head unit. Metra recommends making connections as shown below; Strip, Splice, Solder, Tape. Isolate and individually tape off ends of any unused wires to prevent electrical short circuit. METR / EI WIRING CODE V Ignition / cc.......... Red V att / Memory......... Yellow Ground.................. lack* Power ntenna............ lue mp Turn-On............. lue / White mp Ground.............. lack / White Illumination.............. Orange Dimmer................. Orange / White Right Front (+)............ Gray Right Front (-)............. Gray/ lack Left Front (+)............. White Left Front (-).............. White / lack Right Rear (+)............ Violet Right Rear (-)............. Violet / lack Left Rear (+)............. Green Left Rear (-).............. Green / lack *NOTE: When a lack wire is not present, ground radio to vehicle chassis. ll colors may not be present on all leads due to manufacturer s specifications. 7
99-74 NOTES 8
99-74 NOTES 9
99-74 INSTRUCTIONS -800--09 www.metraonline.com REV. 06/5/09 COPYRIGHT 004-009 METR ELECTRONICS CORPORTION INST99-74