Facts and figures ALLROUNDER 375 V Vertical free-space system Clamping force: 500 kn Injection unit (acc. to EUROMAP): 100, 1, 290 www.arburg.com
375 V Installation dimensions Vertical version 1050 850 3250 1) 3535 2) 3685 3) 3260 1) 3405 2) 3520 3) 2200 115 800 Fixed mould mounting platen 2524 1050 Fixed mould mounting surface Horizontal version 2202 800 4) Horizontal / vertical version 5) Electrical connection 750 564 Cooling water connection 725 514 Pneumatic connection 2130 1) 2410 2) 2560 3) 1) Injection unit 100 2) Injection unit 1 3) Injection unit 290 4) Additional control cabinet dependent on version 5) Position of cooling water connection can vary due to optional equipment 2
Technical data 375 V Clamping unit with clamping force max. kn 0 0 0 0 0 375 V 500 0 0 0 0 0 Version Standard Rotary table Shuttle table Opening force stroke max. kn mm 40 250 40 250 40 250 Mould height, fixed variable min. mm --- 200 --- 1 --- 172 Platen daylight fixed variable max. mm --- 450-550 --- 420-520 --- 422-522 Table diameter mm --- 900 --- Shuttle table stroke mm --- 0 650 Angle of rotation, left/right --- 180 --- 0 Rotation time for 180 min. s --- 2,3 --- Weight on rotary/shuttle table max. kg --- 240 240 Weight of movable mould half max. kg 230 230 230 Ejector force stroke max. kn mm 30 30 30 Dry cycle time EUROMAP ² min. s - mm 3-240 3-240 3-240 Injection unit with screw diameter mm 20 100 25 30 25 1 30 35 30 290 35 40 Effective screw length L/D 25 20 16,7 24 20 17 23,3 20 17,5 Screw stroke max. mm 100 120 150 Calculated stroke volume max. cm³ 31 49 71 59 85 115 106 144 188 Shot weight max. g PS 29 45 65 54 77 105 97 132 172 Material throughput max. kg/h PS 5,5 8 9,5 10 13,5 16 17 20,5 24,5 max. kg/h PA6.6 2,8 4 4,9 5 7 8 8,5 10,5 12,5 Injection pressure max. bar 2500 2000 1390 2500 2000 14 2500 2000 1530 Holding pressure max. bar 2500 2000 1390 2500 2000 14 2500 2000 1530 Injection flow ² max. cm³/s 64 100 146 66 96 132 72 100 130 Screw circumferential speed ² max. m/min 28 35 42 35 42 49 33 39 44 Screw torque max. Nm 120 150 180 250 290 320 380 430 Nozzle contact force retraction stroke max. kn mm 50 180 50 60 240 Heating capacity zones kw 4,9 5 9,4 5 6,4 5 Feed hopper l 25 25 25 Drive and connection with injection unit 100 Standard 1 290 100 Rotary table 1 290 100 Shuttle table 1 290 Net weight of machine kg 3049 3111 3161 3529 3591 3641 3449 3511 3561 Sound press. level Insecurity ⁴ db(a) 65 3 65 3 65 3 Oil filling l 0 160 0 0 160 0 0 160 0 Drive power ² max. kw 0 11 0 0 11 0 0 11 0 Electrical connection ³ kw 18 22 20 18 22 20 18 22 20 Total A 0 63 0 0 63 0 0 63 0 Machine A 0 --- 0 0 --- 0 0 --- 0 Heating A 0 --- 0 0 --- 0 0 --- 0 Cooling water connection max. C min. Δp bar 25 1,5 DN 25 25 1,5 DN 25 25 1,5 DN 25 Machine type with EUROMAP size designation ¹ 375 V 500-100 1 290 0 0 Upon request: other machine types and mould installation heights, screws, drive powers, etc. All specifications relate to the basic machine version. Deviations are possible, depending on variants, process settings and material type. Depending on the drive, certain combinations, e.g. max. injection pressure and max. injection flow may be mutually exclusive. 1) Clamping force (kn) - large injection unit = max. stroke volume (cm³) x max. injection pressure (kbar) 2) Specifications depend on the drive variant / drive configuration. 3) Specifications relate to 400 V/50 Hz. 4) Detailed info in the operating instructions. [ ] Specifications apply to alternative equipment. 3
375 V Mould installation dimensions Cut-out in mould (if required) Y Ø 50 107 15 B 180-5 A Y 1 X R 300 Stroke max. 250 max. 450-550 Stroke max. Ejector bolt X Ø 125 without coupling element with coupling element Coupling element Stroke max. 18 135 127 8,5 max. 15 26 Ø 28 Ø 13,5 Ø 18,5 Injection in the mould parting line Variable a (set in accordance with mould parting line) 1) / 266 2)3) Cut-out in mould (if required) 60 20 a b, fixed mould mounting platen, fixed mould mounting platen Mount for horizontal injection unit Splatter guard Mount for injection in the parting line Ø 50 Ø80 c 233 1) Injection unit 100 2) Injection unit 1 3) Injection unit 290 Injection positions with hydraulic nozzle Injection unit 100 Injection unit 1 Injection unit 290 a min. 100 100 100 100 a max. 200 200 200 200 b min. 100 100 100 100 c min. 96 76 83 76 4
Mould installation dimensions 375 V Fixed mould mounting platen A 286 516 100 250 M12-24 deep 420 Ø 10H8-13 deep 926 504 Ø125 H7 212 330 324 424 35 (Free space up to C frame) 335 Ø125 H7 Rear safety door Ø 10H8-13 deep 195 Moving mould mounting platen B 375 5
375 V Rotary table dimensions Vertical version 1080 850 1) 2) 3) 3250 3535 3685 1) 2) 3) 3260 3405 3520 2015 454 3012 1200 1080 Rotary platen Rotary platen Horizontal version 2202 1200 4) Non-contacting safety device (light curtain) Horizontal / vertical version 5) 725 750 1114 Electrical connection Cooling water connection 1) 25 2990 2) 3 3) 1) Injection unit 100 2) Injection unit 1 3) Injection unit 290 4) Additional control cabinet dependent on version 5) Position of cooling water connection can vary due to optional equipment 6
Mould installation dimensions for rotary table 375 V min.145 / max. 235 (set in accordance with mould parting line)* 107 15 B A 180-5 1 R 300 Stroke min. 250 max. 420-520 Ejector bolt (for gentle ejection) 29,5 +0,1 Ø 26 Mould Rotary table Fixed mould mounting platen, rotary table A 420 Usable mounting surface 896 130 Ø 900 Rear safety door 516 324 Moving mould mounting platen B 504 Ø 900 Ø 550 Couplings Cooling circuits M12-24 deep Ø 125H7 Ø 28 for hydraulic ejector 212 330 424 M12-20 deep For installation in top mould half Non-contacting safety device (light curtain) max. R450 250 375 Ø 10H8-13 deep *) Maximum height: Observe mould parting line with ejector stroke or height of sprue in case of vertical injection unit 7
375 V Overall dimensions - sliding table Vertical version 1078 1) 2) 3) 3250 3535 3685 1) 3260 3405 2) 3) 3520 2015 169 800 2578 Horizontal version 1078 Sliding platen 2202 Sliding platen 800 4) Horizontal / vertical version 5) *) 2400 Electrical connection Cooling water connection Pneumatic connection 1) 2) 3) 2 2495 2645 1) Injection unit 100 2) Injection unit 1 3) Injection unit 290 4) Additional control cabinet dependent on version 5) Position of cooling water connection can vary due to optional equipment *) Non-contacting safety device (light curtain) 8
Mould installation dimensions - sliding table 375 V ( 291 ) Ejector bolt (for gentle ejection) 28 Height, sliding platen to mounting surface 107 60 15 A 15 B 180-5 1 R 300 Stroke max. 250 max. 422-522 25,5 +0,1 26 Mould Sliding table Sliding table A Usable mounting surface Ø 30 for hydraulic ejector Stroke 650 Stroke 650 Rear safety door M12-18 deep Ø 30 for hydraulic ejector 480 480 246 516 324 Non-contacting safety device (light curtain) Ø 125 H7 Distance from sliding platen to bar 2 Height, sliding platen 26 420 420 Moving mould mounting platen B 125 H7 504 212 330 424 Ø 10H3-13 deep 250 375 M12-24 deep 9
375 V Shot weights Theoretical shot weights for the most important injection moulding materials Injection units according to EUROMAP Screw diameter mm Polystyrene max. g PS Styrene heteropolymerizates max. g SB max. g SAN, ABS 1) Cellulose acetate max. g CA 1) Celluloseacetobutyrate max. g CAB 1) Polymethyl methacrylate max. g PMMA Polyphenylene ether, mod. max. g PPE Polycarbonate max. g PC Polysulphone max. g PSU Polyamides max. g PA 6.6 PA 6 1) max. g PA 6.10 PA 11 1) Polyoximethylene (Polyacetal) max. g POM Polyethylene terephthalate max. g PET Polyethylene max. g PE-LD max. g PE-HD Polypropylene max. g PP Fluorpolymerides max. g FEP, PFA, PCTFE 1) max. g ETFE Polyvinyl chloride max. g PVC-U max. g PVC-P 1) 100 20 25 30 29 45 65 28 44 63 27 43 62 32 50 73 30 47 68 30 46 67 27 42 60 30 47 68 31 49 28 44 64 26 41 60 35 55 80 34 53 77 22 34 49 22 35 50 23 36 51 46 72 103 40 63 91 35 54 78 32 50 72 1 25 30 35 54 77 105 53 76 103 52 74 101 61 87 119 56 81 110 56 80 109 50 72 98 57 81 111 58 84 115 53 77 104 50 72 98 66 96 130 64 92 126 41 59 80 42 60 82 43 62 84 86 124 169 76 109 148 65 94 127 60 87 118 290 30 35 40 97 132 172 95 129 168 93 126 165 109 148 194 101 138 180 100 136 178 90 122 160 102 139 181 105 143 187 96 131 171 90 122 160 120 163 213 115 157 205 73 100 130 76 103 134 77 105 137 155 211 276 136 185 242 117 159 208 108 147 192 1) average value ARBURG GmbH + Co KG Arthur-Hehl-Strasse 72290 Lossburg Tel.: +49 7446 33-0 www.arburg.com E-Mail: contact@arburg.com With locations in Europe: Germany, Belgium, Denmark, France, United Kingdom, Italy, Netherlands, Austria, Poland, Switzerland, Slovakia, Spain, Czech Republic, Turkey, Hungary Asia: People s Republic of China, Indonesia, Malaysia, Singapore, Taiwan, Thailand, United Arab Emirates America: Brazil, Mexico, USA For more information, please go to www.arburg.com. 2017 ARBURG GmbH + Co KG The brochure is protected by copyright. Any utilisation, which is not expressly permitted under copyright legislation, requires the previous approval of ARBURG. All data and technical information have been compiled with great care. However we accept no responsibility for correctness. Individual illustrations and information may deviate from the actual delivery condition of the machine. The relevant valid operating instructions are applicable for the installation and operation of the machine. ARBURG GmbH + Co KG DIN EN ISO 9001 + 01 + 50001 certified 680185_EN_GB_092017 Subject to alterations