EARTHMASTER Pub 11/05 1165 S/N 2300 -CURRENT Part No. 4353P 1465 S/N 1239 -CURRENT PART'S MANUAL An Operator's Manual was shipped with the equipment in the Manual Canister. This Operator's Manual is an integral part of the safe operation of this machine and must be maintained with the unit at all times. READ, UNDERSTAND, and FOLLOW the Safety and Operation Instructions contained in this manual before operating the equipment. If the Operator's Manual is not with the equipment, contact your dealer or M&W (800-446-5158) to obtain a Free copy before operating the equipment. MODEL 965, 1165, & 1465 M&W 1020 South Sangamon Ave. Gibson City, Illinois 60936 217-784-4261 2005 Alamo Group Inc.
TO THE OWNER/OPERATOR/DEALER All implements with moving parts are potentially hazardous. There is no substitute for a cautious, safe-minded operator who recognizes the potential hazards and follows reasonable safety practices. The manufacturer has designed this implement to be used with all its safety equipment properly attached to minimize the chance of accidents. BEFORE YOU START!! Read the safety messages on the implement and shown in your manual. Observe the rules of safety and common sense! WARRANTY INFORMATION: Read and understand the complete Warranty Statement found in this Manual. Fill out the Warranty Registration Form in full and return it within 30 Days. Make certain the Serial Number of the Machine is recorded on the Warranty Card and on the Warranty Form that you retain. The use of "will-fit" parts will void your warranty and can cause catastrophic failure with possible injury or death.
Parts Section 1 PARTS SECTION
PARTS ORDERING GUIDE The following instructions are offered to help eliminate needless delay and error in processing purchase orders for the equipment in this section. 1. The Parts Section is prepared in logical sequence and grouping of parts that belong to the basic machine featured in this manual. Part Numbers and Descriptions are given to help locate the parts and quantities required. 2. The Purchase Order must include the name and address of the person or organization ordering the parts, who should be charged, and if possible, the serial number of the machine for which the parts are ordered. 3. The Purchase Order must clearly list the quantity of each part, the complete and correct part number, and the basic name of the part. 4. The Manufacturer reserves the right to substitute parts where applicable. 5. Some parts are unlisted items which are special production items not normally stocked and are subject to special handling. Request a quotation for such parts before sending a Purchase Order. 6. The Manufacturer reserves the right to change prices without prior notice. NOTE: Please refer to The Safety Section in the front of this Manual for the proper Part Number when ordering Replacement Safety Decals. For maximum safety and to guarantee optimum product reliability, always use genuine Alamo Group Parts. The use of inferior replacement parts may cause premature or catastrophic failure which could result in serious injury or death. Direct any questions regarding parts to: M&W 1020 South Sangamon Ave. Gibson City, Illinois 60936 217-784-4561 2005 Alamo Group Inc. Parts Section 2
PART NAME INDEX AUTOMATIC RESET SHANK... 18 AUTOMATIC RESET STRAIGHT SHANK... 20 AXLE ASSEMBLY 1165S/N 2299 1475S/N 1238 -BELOW Pub 11-05... 8 AXLE ASSEMBLY 1165S/N 2300 1475S/N 1239 -CURRENT Pub 11-05... 7 CHISEL POINT REMOVABLE PIN KIT NO. 2420479 INSTALLATION INSTRUCTIONS... 35 DISC FRAME... 4 DISC GANG... 9 DRAGBAR HARROW INSTRUCTIONS... 32, 34 HYDRAULIC ASSEMBLY... 12, 13 HYDRAULIC CYLINDER #2420178... 11 HYDRAULIC TONGUE CYLINDER #2420177... 10 MANUAL RESET SHANK... 16 RIDGEMASTER... 30 RIGID DISC SCRAPER... 26, 27, 28 TONGUE ASSEMBLY... 6 V-CHISEL BAR COULTER... 24 V-CHISEL BAR GAUGE WHEEL... 22 V-CHISEL BAR MODEL 1165 & 1465... 15 V-CHISEL BAR MODEL 965... 14 1165 & 1465 EARTHMASTER LIGHT KIT INSTALLATION SHEET... 29 2005 Alamo Group Inc. Parts Section 3
DISC FRAME 2005 Alamo Group Inc. Parts Section 4
DISC FRAME ITEM PART NO. QTY. DESCRIPTION 1 2430326 1 DISC FRAME 2 2438307 2 DECAL, EARTHMASTER 3 2438323 2 DECAL, MODEL 1465 2438324 2 DECAL, MODEL 1165 2438331 2 DECAL, MODEL 965 4 31797H5C 4 BOLT 5 2438312 1 DECAL, CAUTION 6 2438313 1 DECAL, MAINTENANCE 7 2430301 2 FRONT GANG TUBE, MODEL 1465 2430299 2 FRONT GANG TUBE, MODEL 1165 2430329 2 FRONT GANG TUBE, MODEL 965 8 2738333 2 DECAL, YELLOW OBLONG REFLECTOR 9 350012C 12 LOCKWASHER 10 330010C 12 HEX NUT 11 2431525 4 GANG CLAMP PLATE 12 2430302 2 REAR GANG TUBE, MODEL 1465 2430300 2 REAR GANG TUBE, MODEL 965 & 1165 13 2738332 2 DECAL, RED OBLONG REFLECTOR 14 317917H5C 8 BOLT 15 49054 6 COTTER PIN 16 F102 7 KLICK PIN 17 420816 6 ROLL PIN 18 2432511 2 PIN 19 2432540 2 REAR HITCH 20 2432539 4 STOP PIN 21 2430293 2 REAR TOGGLE HITCH BAR 22 2438407 1 BUSHING, SPRING 23 2430297 1 SCREW LINK 24 2430257 1 PIN 25 2431279 1 LOCK TAB 26 2430253 1 ADJUSTING SCREW - 965 26A 2420252 1 ADJUSTING SCREW - 1165 & 1465 27 45051 3 GREASE FITTING 28 2430298 1 ADJUSTING SCREW YOKE 29 2432513 1 PIN 30 2438329 1 DECAL, PATENT NO. 31 2431561 4 U-BOLT 32 33008C 16 HEX NUT 33 2438332 1 DECAL, GREASE, 8 HOUR 34 2438345 2 DECAL, M&W 2005 Alamo Group Inc. Parts Section 5
TONGUE ASSEMBLY ITEM PART NO. QTY. DESCRIPTION 2 2435516 1 HITCH 3 330812C 1 HEX SLOTTED NUT 4 49055 1 COTTER PIN 5 2430295 1 HITCH MOUNT PIN 6 1338600 1 JACK 7 2438326 1 DECAL, JACK 8 2430291 1 TONGUE 9 2432553 2 TONGUE MOUNT PIN 10 420915 4 ROLL PIN 2005 Alamo Group Inc. Parts Section 6
AXLE ASSEMBLY 1165S/N 2300 1475S/N 1239 -CURRENT Pub 11-05 ITEM PART NO. QTY. DESCRIPTION 1 2430356 1 AXLE STRUT W/HUBS 2 2410207 1 AXLE STRUT W/O HUBS 3 2438407 1 BUSHING, SPRING 4 45051 5 GREASE FITTING 5 49055 2 COTTER PIN 6 330812C 2 HEX SLOTTED NUT 7 0536013 4 BRONZE BUSHING 8 2430296 2 AXLE MOUNT PIN 9 2238400 16 WHEEL STUD 10 6W300 16 LUG NUT 11 02021500 2 SEAL 12 02707700 2 BEARING CONE, INNER 13 02708100 2 BEARING CUP, INNER 14 0535508 2 HUB, 8-BOLT 15 00749492 2 BEARING CUP, OUTER 16 6W507 2 BEARING CONE, OUTER 17 00724462 2 SPINDLE WASHER 18 49035 2 COTTER PIN, 5/32 X 1-3/4 19 33099C 2 HEX SLOTTED NUT, 7/8-14 20 00772500 2 HUB CAP 21 2437600 2 WHEEL 22 TR415 2 VALVE STEM 23 0527802 2 TIRE 24 2420130 2 WHEEL & TIRE ASSEMBLY 25 2438332 3 DECAL, 8 HOUR GREASE 2005 Alamo Group Inc. Parts Section 7
AXLE ASSEMBLY 1165S/N 2299 1475S/N 1238 -BELOW Pub 11-05 ITEM PART NO. QTY. DESCRIPTION 1 2430356 1 AXLE STRUT W/HUBS 2 2410207 1 AXLE STRUT W/O HUBS 3 2438407 1 BUSHING, SPRING 4 45051 5 GREASE FITTING 5 49055 2 COTTER PIN 6 330812C 2 HEX SLOTTED NUT 7 0536013 4 BRONZE BUSHING 8 2430296 2 AXLE MOUNT PIN 9 2238400 16 WHEEL STUD 10 6W300 16 LUG NUT 11 0536803 2 SEAL 12 0536021 2 BEARING CONE 13 0536022 2 BEARING CUP 14 0535505 2 HUB 15 0536016 2 BEARING CUP 16 0536014 2 BEARING CONE 17 380010C 2 FLATWASHER 18 49034 2 COTTER PIN 19 330910C 2 HEX SLOTTED NUT 20 0536701 2 HUB CAP 21 2437600 2 WHEEL 22 TR415 2 VALVE STEM 23 0527802 2 TIRE 24 2420130 2 WHEEL & TIRE ASSEMBLY 25 2438332 3 DECAL, 8 HOUR GREASE 2005 Alamo Group Inc. Parts Section 8
DISC GANG ITEM PART NO. QTY 965 QTY 1165 QTY 1465 DESCRIPTION 1 2430304 0 0 4 DISC AXLE, 80" 2430303 2 4 0 DISC AXLE, 65" 2430330 2 0 0 DISC AXLE, 50" 2 2436510 4 4 4 BUMPER END CAP 3 2438356 18 18 22 DISC 4 2460446 8 8 12 MALE BEARING SPOOL 5 2435511 8 8 12 TRUNNION HOUSING 6 45051 8 8 12 GREASE FITTING 7 2436506 16 16 24 TRUNNION MOUNT 8 2435501 6 8 8 SPOOL 9 2438355 0 2 2 DISC 10 2436500 4 4 4 MALE END CAP 11 2431150 4 4 4 NUT LOCK TAB 12 330014C 4 4 4 HEX NUT 13 2460447 8 8 12 FEMALE BEARING SPOOL 14 2436800 16 16 24 SEAL 15 2438201 16 16 24 RETAINING RING 16 2436004 8 8 12 DOUBLE TAPERED BEARING 16A 2236000 16 16 24 BEARING CUP 17 31709H5C 16 16 24 BOLT 18 33008C 40 40 60 HEX NUT 19 35009C 40 40 60 LOCKWASHER 20 2437500 8 8 12 BEARING HANGER SPRING 21 2431418 16 16 28 CLAMP PLATE 22 317020H5C 24 24 24 BOLT 23 2430357 8 8 12 SPRING STOP 24 2431436 8 8 8 SCRAPER MOUNT PLATE 2005 Alamo Group Inc. Parts Section 9
HYDRAULIC TONGUE CYLINDER #2420177 ITEM PART NO. QTY. DESCRIPTION 1 2417163 1 CYLINDER ROD 2 2417164 1 CYLINDER TUBE 3 2417162 1 CYLINDER HEAD 4 2417165 1 PISTON 5 5JRC12160 1 NUT 6 ----- 1* ROD SEAL 7 ----- 1* ROD WIPER 8 ----- 1* O-RING 9 ----- 1* SEAL 10 ----- 1* O-RING 11 ----- 1* SEAL 12 2717166 2 PLUG 13 2437137 1 TEE 14 2437136 1 ADAPTER * 02975529 1 SEAL KIT 2005 Alamo Group Inc. Parts Section 10
HYDRAULIC CYLINDER #2420178 ITEM PART NO. QTY. DESCRIPTION 1 2417171 1 CYLINDER ROD 2 2417170 1 CYLINDER TUBE 3 2417169 1 CYLINDER HEAD 4 2417173 1 PISTON 5 02963358 1 LOCKNUT 6 ----- 1* ROD SEAL 7 ----- 1* ROD WIPER SEAL 8 ----- 1* O-RING 9 ----- 1* SEAL 10 ----- 1* O-RING 11 ----- 1* SEAL 12 1917132 2 PLUG 13 2417168 2 BUSHING 14 2417172 1 CYLINDER ROD CLEVIS 15 11554 2 90DEGREES ELBOW 16 380460C 2 FLATWASHER 17 00774740 1 SETSCREW 18 3047117 1 THREAD LOCK * 2417174 1 KIT,SEAL 45W-175 2005 Alamo Group Inc. Parts Section 11
HYDRAULIC ASSEMBLY ITEM PART NO. QTY. DESCRIPTION 1 2432513 2 PIN 2 49054 4 COTTER PIN 3 2430253 1 ADJUSTING SCREW 4 2434792 1 TONGUE CYLINDER LOCK 5 45051 1 GREASE FITTING 6 2420177 1 TONGUE CYLINDER 7 11773 2 MALE RUN TEE 8 2437210 2 HOSE 9 F102 1 KLICK PIN 10 2430257 1 TRANSPORT LOCK PIN 11 11554 2 ELBOW, 90DEGREES 12 2437212 1 HOSE 13 2437213 1 HOSE 14 2432555 1 CYLINDER PIN 15 380460C 6 FLATWASHER 16 2420178 1 HYDRAULIC CYLINDER ASSY. 17 2432538 1 CYLINDER LOCK RETAINER PIN 18 42069 1 ROLL PIN 19 F101 1 KLICK PIN 20 2430358 1 CYLINDER TRANSPORT LOCK 21 2432554 1 UPPER CYLINDER PIN 22 02972180 1 HYD. ADAPTER STRAIGHT 23 2457350 1 BALL VALVE 24 49055 4 COTTER PIN 25 2437138 2 HYD. ADAPTER 2005 Alamo Group Inc. Parts Section 12
HYDRAULIC ASSEMBLY ITEM PART NO. QTY. DESCRIPTION 1 2432513 2 PIN 2 49054 4 COTTER PIN 3 2430253 1 ADJUSTING SCREW 4 2434792 1 TONGUE CYLINDER LOCK 5 45051 1 GREASE FITTING 6 2437127 1 TONGUE CYLINDER ASSEMBLY 7 11844 2 MALE RUN TEE 8 2437210 2 HOSE 9 F102 1 KLICK PIN 10 2430257 1 TRANSPORT LOCK PIN 11 2438316 1 DECAL, LOCK CAUTION 12 11528 2 MALE ELBOW 13 2437212 1 HOSE 14 2437213 1 HOSE 16 2432555 1 CYLINDER PIN 17 380460C 4 FLATWASHER 18 2438328 1 DECAL, LOCK CAUTION 19 2420131 1 HYDRAULIC CYLINDER 20 2432538 1 CYLINDER LOCK RETAINER PIN 21 42069 1 ROLL PIN 22 F101 1 KLICK PIN 23 2430358 1 CYLINDER TRANSPORT LOCK 24 2432554 1 UPPER CYLINDER PIN 25 10011EH 1 PIPE NIPPLE 26 1437351 1 BALL VALVE 27 49055 4 COTTER PIN 28 2738314 1 DECAL, LUBRICATION 2420131 1 CYLINDER ASSEMBLY, (INCLUDES ITEMS 18,19, & 28) 2430167 1 TONGUE CYLINDER ASSEMBLY (INCLUDES ITEMS 3,5,6, & 11) 2432513 PISTON 2417136 GUIDE 329812H8C NUT LOCK 2417139 SEAL KIT 2417135 ROD 2417134 CYLINDER BODY 2417137 RETAINING PLATE 2417138 CLEVIS MC W/ BUSHING 2005 Alamo Group Inc. Parts Section 13
V-CHISEL BAR MODEL 965 ITEM PART NO. QTY. DESCRIPTION 1 2430306 1 V-CHISEL BAR 2 420816 3 ROLL PIN 3 F102 3 KLICK PIN 4 2420273 2 LOWER HITCH PIN 5 2432503 1 UPPER HITCH PIN 6 2432505 1 UPPER HITCH PIN 7 2432504 1 UPPER HITCH PIN 8 2738332 2 DECAL, RED REFLECTOR 9 2438300 2 DECAL, EARTHMASTER 10 2738333 1 DECAL, YELLOW REFLECTOR 11 2196 2 CLIP 2005 Alamo Group Inc. Parts Section 14
V-CHISEL BAR MODEL 1165 & 1465 ITEM PART NO. QTY. DESCRIPTION 1 2430392 1 V-CHISEL BAR 1165 & 1465 2 420816 3 ROLL PIN 3 F102 3 KLICK PIN 4 2420273 2 PIN 5 2432503 1 UPPER HITCH PIN 6 2432505 1 UPPER HITCH PIN - 965 7 2432504 1 UPPER HITCH PIN - 965 8 2738332 2 DECAL, RED REFLECTOR 9 2438300 2 DECAL, EARTHMASTER 10 2738333 1 DECAL, YELLOW REFLECTOR 11 2420275 2 TURNBUCKLE PIN 14 2196 3 CLIP 2005 Alamo Group Inc. Parts Section 15
MANUAL RESET SHANK 2005 Alamo Group Inc. Parts Section 16
MANUAL RESET SHANK ITEM PART NO. QTY. Center QTY. RH QTY. LH DESCRIPTION 1 2430226 1 0 0 CENTER TRIP SHANK MOUNT 2 2438358 1 1 1 MANUAL SHANK* 3 2432509 1 1 1 LEAF SPRING PIN 4 2432030 2 2 2 SPACER PLATE 5 31709H5C 1 1 1 BOLT 6 32908C 1 1 1 HEX LOCKNUT 7 31809H5C 1 1 1 BOLT 8 32909C 1 1 1 HEX LOCKNUT 9 317016H5C 4 0 0 BOLT 10 35009C 4 4 4 LOCKWASHER 11 33008C 4 4 4 HEX NUT 12 38008C 2 2 2 FLATWASHER 13 2432510 1 1 1 TRIP PIN 14 49053 4 4 4 COTTER PIN 15 2437420 1 1 1 LEAF SPRING SUPPORT 16 2430227 1 1 1 STUD 17 32925C 1 1 1 ELASTIC STOP NUT 18 2437421 1 1 1 LEAF SPRING, SHORT 19 2437422 1 1 1 LEAF SPRING, MIDDLE 20 2437423 1 1 1 LEAF SPRING, LONG 21 2410400 1 1 1 CHISEL POINT & PEN 23 2434856 1 1 1 SPACER TUBE 24 2431456 0 1 1 SHANK MOUNT PLATE 25 2430336 0 0 1 TRIP SHANK MOUNT, LH 26 2430335 0 1 0 TRIP SHANK MOUNT, RH 27 317017H5C 0 4 4 BOLT 28 2418402 1 1 1 SPECIAL OVERSIZED PIN FOR CHISEL POINT 2430124 CENTER SHANK ASSEMBLY, COMPLETE 2430122 SHANK ASSEMBLY, RH, COMPLETE 2430123 SHANK ASSEMBLY, LH, COMPLETE * 2430178 SHANK, POINT & PIN ASSEMBLY (INCLUDES ITEMS 2005 Alamo Group Inc. Parts Section 17
AUTOMATIC RESET SHANK 2005 Alamo Group Inc. Parts Section 18
AUTOMATIC RESET SHANK ITEM PART NO. QTY. Center QTY. RH QTY. LH DESCRIPTION 1 2430333 1 0 0 SHANK MOUNT, CENTER 2 2430331 0 1 0 SHANK MOUNT, RH 3 2430332 0 0 1 SHANK MOUNT, LH 4 317017H5C 0 4 4 BOLT 5 317016H5C 4 0 0 BOLT 6 35009C 4 4 4 LOCKWASHER 7 33008C 4 4 4 HEX NUT 8 2430261 1 1 1 PIVOT PIN 9 2430262 1 1 1 PULL ARM PIN 10 49053 4 4 4 COTTER PIN 11 380450C 2 2 2 FLATWASHER 12 2432543 1 1 1 SPRING YOKE 13 2430334 1 1 1 PULL ARM 14 2410400 1 1 1 CHISEL POINT & PIN 15 2430275 1 1 1 PULL ARM TO MOUNT PIN 16 2438360 1 1 1 AUTOMATIC SHANK* 17 2438404 1 1 1 SHANK WASHER 18 331212C 2 2 2 NYLON INSERT JAM NUT 19 2432523 1 1 1 PIVOT PIN 20 420916 1 1 1 ROLL PIN 21 420619 1 1 1 ROLL PIN 22 2435508 1 1 1 OUTER TOGGLE 23 2435507 1 1 1 INNER TOGGLE 24 2431106 1 1 1 STOP 25 35002C 1 1 1 LOCKWASHER 26 31102H5C 1 1 1 BOLT 27 331210C 1 1 1 NYLON INSERT JAM LOCKNUT 28 2430265 2 2 2 SPRING GUIDE BAR 29 2437424 2 2 2 SPRING 30 2435509 2 2 2 SPRING INSERT, END PLUG 31 2430319 1 0 0 CENTER SPRING TUBE 32 2430320 0 1 1 SPRING TUBE 33 2431882 2 2 2 FLATWASHER 34 300516H5C 2 2 2 HEX TAP BOLT 35 2432521 1 1 1 TOGGLE PIN 36 45053 1 1 1 GREASE FITTING 37 45051 5 5 5 GREASE FITTING 38 2432301 2 2 2 TOGGLE WASHER 39 2432300 4 4 4 PULL ARM WASHER 40 380454C 2 2 2 FLATWASHER 41 2434866 2 2 2 ROLLER 42 2431456 0 1 1 SHANK MOUNT PLATE 43 2431602 0 2 2 TIE PLATE 44 31103C 0 2 2 BOLT 45 38005C 0 2 2 FLATWASHER 46 6D9016 0 2 2 HEX WHIZLOCK NUT 47 2438332 1 1 1 DECAL, 8 HOUR GREASE 48 2418402 1 1 1 SPECIAL OVERSIZED PIN FOR CHISEL POINT 2420123 SHANK ASSEMBLY, CENTER, COMPLETE 2420121 SHANK ASSEMBLY, RH, COMPLETE 2420122 SHANK ASSEMBLY, LH, COMPLETE 2430179 SHANK, POINT AND PIN ASSEMBLY (INCLUDES ITEMS 14 & 16) 2005 Alamo Group Inc. Parts Section 19
AUTOMATIC RESET STRAIGHT SHANK 2005 Alamo Group Inc. Parts Section 20
AUTOMATIC RESET STRAIGHT SHANK ITEM PART NO. QTY. CENTER QTY. RH QTY. LH DESCRIPTION 1 2430333 1 0 0 SHANK MOUNT, CENTER 2 2430331 0 1 0 SHANK MOUNT, RH 3 2430332 0 0 1 SHANK MOUNT, LH 4 317017H5C 0 4 4 BOLT 5 02025700 4 0 0 BOLT 6 35009C 4 4 4 LOCKWASHER 7 00000200 4 4 4 NUT 8 2430261 1 1 1 PIVOT PIN 9 2430262 1 1 1 PULL ARM PIN 10 49053 4 4 4 COTTER PIN 11 15B1400 2 2 2 FLATWASHER 12 2432543 1 1 1 SPRING YOKE 13 2430334 1 1 1 PULL ARM 14 2450269 1 1 1 CHISEL POINT 15 2430275 1 1 1 PULL ARM TO MOUNT PIN 16 2450285 1 1 1 STRAIGHT AUTOMATIC SHANK* 17 2438404 1 1 1 SHANK WASHER 18 331212C 2 2 2 NYLON INSERT JAM NUT 19 2432523 1 1 1 PIVOT PIN 20 420916 1 1 1 ROLL PIN 21 420619 1 1 1 ROLL PIN 22 2435508 1 1 1 OUTER TOGGLE 23 2435507 1 1 1 INNER TOGGLE 24 2431106 1 1 1 STOP 25 00011700 1 1 1 LOCKWASHER 26 31102H5C 1 1 1 BOLT 27 331210C 1 1 1 NYLON INSERT JAM LOCKNUT 28 2430265 2 2 2 SPRING GUIDE BAR 29 2437424 2 2 2 SPRING 30 2435509 2 2 2 SPRING INSERT, END PLUG 31 2430319 1 0 0 CENTER SPRING TUBE 32 2430320 0 1 1 SPRING TUBE 33 2431882 2 2 2 FLATWASHERS 34 300516H5C 2 2 2 TAP BOLT 35 2432521 1 1 1 TOGGLE PIN 36 45053 1 1 1 GREASE FITTING 37 45051 5 5 5 GREASE FITTING 38 2432301 2 2 2 TOGGLE WASHER 39 2432300 4 4 4 PULL ARM WASHER 40 15B1600 2 2 2 FLATWASHER 41 2434866 2 2 2 ROLLER 42 2431456 0 1 1 SHANK MOUNT PLATE 43 2431602 0 2 2 TIE PLATE 44 31103C 0 2 2 BOLT 45 00002700 0 2 2 FLATWASHER 46 6D9016 0 2 2 WHIZLOCK NUT 47 2438332 1 1 1 DECAL, GREASE, 8 HOUR 48 02027400 1 1 1 BOLT 49 00001800 1 1 1 TOP LOCKNUT 50 32905C 1 1 1 LOCKNUT 51 02788400 1 1 1 BOLT 52 2456503 1 1 1 SHANK PROTECTOR 2450132 CENTER SHANK ASSEMBLY, COMPLETE 2450130 SHANK ASSEMBLY, RH, COMPLETE 2450131 SHANK ASSEMBLY, LH, COMPLETE 2450133 SHANK & POINT ASSEMBY (INCLUDES ITEMS 14, 16 & 48-52) 2005 Alamo Group Inc. Parts Section 21
V-CHISEL BAR GAUGE WHEEL 2005 Alamo Group Inc. Parts Section 22
V-CHISEL BAR GAUGE WHEEL ITEM PART NO. QTY. DESCRIPTION 1 2420268 2 STRUT TUBE 2 2422503 2 SPINDLE 3 2420201 1 MOUNT PLATE, LH 4 2420200 1 MOUNT PLATE, RH 5 2420203 1 CLAMP PLATE, LH 6 2420202 1 CLAMP PLATE, RH 7 2422501 4 PIN 8 2428600 2 TURNBUCKLE JACK 9 317914C 2 BOLT 10 317017H5C 8 BOLT 11 33008C 8 HEX NUT 12 35009C 8 LOCKWASHER 13 329010C 2 HEX LOCKNUT 14 49044 8 COTTER PIN 16 0536801 2 SEAL 17 0536009 2 BEARING CONE 18 0536008 2 BEARING CUP 19 0538400 12 DRIVE STUD 20 0538401 12 STUD NUT 21 0535501 2 HUB 22 0536002 2 BEARING CUP 23 0536003 2 BEARING CONE 24 38008C 2 FLATWASHER 25 33098C 2 HEX SLOTTED NUT 26 49033 2 COTTER PIN 27 0536700 2 HUB CAP 28 TR415 2 VALVE STEM 29 2427600 2 WHEEL 30 0527800 2 TIRE 31 312012H5C 2 BOLT 32 32903C 2 HEX LOCKNUT 2 2422503 1 SPINDLE 16 0536801 1 SEAL 17 0536009 1 BEARING CONE 18 0536008 1 BEARING CUP 19 0538400 6 DRIVE STUD 20 0538401 6 STUD NUT 21 0535501 1 HUB 22 0536002 1 BEARING CUP 23 0536003 1 BEARING CONE 24 38008C 1 FLATWASHER 25 33098C 1 HEX SLOTTED NUT 26 49033 1 COTTER PIN 27 0536700 1 HUB CAP 28 TR475 1 VALVE STEM 29 2427600 1 WHEEL 30 0527800 1 TIRE 31 312012H5C 1 BOLT 32 32903C 1 HEX LOCKNUT 2005 Alamo Group Inc. Parts Section 23
V-CHISEL BAR COULTER 2005 Alamo Group Inc. Parts Section 24
V-CHISEL BAR COULTER ITEM PART NO. QTY. DESCRIPTION 1 2428351 1 COULTER ASSEMBLY (INCLUDES ITEMS 10-34) 2 2422502 1 COULTER MOUNT ROD 3 2420207 1 COULTER MOUNT ARM 4 420915 2 ROLL PIN 5 3904A6C 2 SQUAREHEAD SCREW 6 33115C 2 HEX JAM NUT 7 35009C 2 LOCKWASHER 8 33008C 4 HEX NUT 9 317010C 2 BOLT 10 30708H5C 1 BOLT 11 2417500 1 PUSH ROD 12 33108C 1 HEX JAM NUT 13 3905A6C 1 SQUAREHEAD SETSCREW 14 2417501 1 LOCKING COLLAR 15 49054 1 COTTER PIN 16 2418400 1 WASHER 17 2417502 1 HINGE CASTING 18 2417421 1 SPRING 19 2417503 1 SPRING BUSHING 21 32918C 1 HEX LOCKNUT 22 2417504 1 COULTER ARM 23 2417505 1 SPACER 24 6W702 1 SEAL 25 0536003 2 BEARING CONE 26 0536002 2 BEARING CUP 27 37053C 4 CARRIAGE BOLT 28 2417506 1 HUB ASSEMBLY 29 35005C 4 LOCKWASHER 30 33005C 4 HEX NUT 31 2418401 1 RETAINER WASHER 32 32917C 1 HEX LOCKNUT 33 0536700 1 HUB CAP 34 2418352 1 COULTER BLADE 2005 Alamo Group Inc. Parts Section 25
RIGID DISC SCRAPER ITEM PART NO. QTY 965 QTY 1165 QTY 1465 DESCRIPTION 1 2425004 2 0 0 SCRAPER MOUNT TUBE, 50" 2 2425000 2 4 0 SCRAPER MOUNT TUBE, 65" 3 2425001 0 0 4 SCRAPER MOUNT TUBE, 80" 6 2428401 8 8 8 U-BOLT 7 38005C 16 16 16 FLATWASHER 8 35005C 16 16 16 LOCKWASHER 9 33005C 16 16 16 HEX NUT 11 0627504 36 40 48 U-BOLT 12 2420253 9 10 12 RIGID SCRAPER, RH FRONT, LH REAR 13 2420254 9 10 12 RIGID SCRAPER, LH FRONT, RH REAR 14 38003C 36 40 48 FLATWASHER 15 35003C 72 80 96 LOCKWASHER 16 33003C 72 80 96 HEX NUT 2005 Alamo Group Inc. Parts Section 26
RIGID DISC SCRAPER 2005 Alamo Group Inc. Parts Section 27
RIGID DISC SCRAPER 2005 Alamo Group Inc. Parts Section 28
1165 & 1465 EARTHMASTER LIGHT KIT INSTALLATION SHEET ITEM PART NO. QTY. DESCRIPTION 1 1457937 1 RH LAMP 2 1457938 1 LH LAMP 4 2437900 1 WISHBONE HARNESS 5 1457939 1 MAIN HARNESS 6 32901C 8 LOCKNUT 7 10058000 8 BOLT 8 5E805 12 TY-RAP 9 2420233 2 LIGHT BRACKET 2005 Alamo Group Inc. Parts Section 29
RIDGEMASTER 2005 Alamo Group Inc. Parts Section 30
RIDGEMASTER ITEM PART NO. QTY 4/5 Shank QTY 7 Shank QTY 9 Shank DESCRIPTION 1 MW2951 1 1 1 ARM, LH 2 MW295R 1 1 1 ARM, RH (NOT SHOWN) 3 MW296 2 2 2 BOTTOM PLATE 4 MW5002 18 24 30 PLATE 5 DD0056 4 4 4 U-BOLT 6 2428354 6 8 10 S-TINE 7 MW5003 6 8 10 SHOVEL 8 314021H5C 24 32 40 BOLT 9 316019H5C 8 8 8 BOLT 10 35007C 16 16 16 LOCKWASHER 11 33007C 16 16 16 HEX NUT 12 35005C 24 32 40 LOCKWASHER 13 33005C 24 32 40 HEX NUT 14 37644H5C 12 16 20 PLOW BOLT 15 38004C 12 16 20 FLATWASHER 16 32904C 12 16 20 HEX LOCKNUT 17 MW3312 1 0 0 TUBE, 144" MW3314 0 1 0 TUBE, 168" MW3317 0 0 1 TUBE, 204" 18 3708 2 2 2 DECAL, M&W GENERAL 19 2738332 2 2 2 DECAL, RED OBLONG REFLECTOR HOW TO INSTALL YOUR RIDGEMASTER A. Assemble arm weldment to V-Chisel (Shank must clear tube when it trips). B. Assemble tube in highest position. C. Assemble an S-Tine with shovel between each ripper shank in its highest position. D. On the first trial run operate the Earthmaster to the desired working depth. E. Adjust the S-Tine and shovel down so shovel will penetrate tilled ground 2" - 4". NOTE: THE RIDGEMASTER IS NOT DESIGNED TO PENETRATE UNTILLED GROUND 2005 Alamo Group Inc. Parts Section 31
DRAGBAR HARROW INSTRUCTIONS 2005 Alamo Group Inc. Parts Section 32
DRAGBAR HARROW INSTRUCTIONS ITEM PART NO. QTY. DESCRIPTION 1 DD0071 TENSION SPRING 2 PD013 ANCHOR CHAIN 3 31207C BOLT 4 38003C FLATWASHER 5 35003C LOCKWASHER 6 33003C HEX NUT 7 DD0036 PIVOT PIN 8 CP150 SWING ARM 9 49208 HAIR PIN 10 M291N UPPER SUPPORT ARM 11 M290N UPPER SUPPORT ARM 12 37032C CARRIAGE BOLT 13 PD111 TOOTH 14 PD119 U-BOLT 15 35005C LOCKWASHER 16 33005C HEX NUT 18 316020H5C BOLT 19 35007C LOCKWASHER 20 33007C HEX NUT 21 PD107 BAR, 7 PD110 BAR, 10 PD113 BAR, 13 NOTE: The above is complete MW3001 and MW3002 Arm Assemblies. The Arm Assemblies include everything shown except (21), (13) and the bolt, washer and nut to install the tooth. 2005 Alamo Group Inc. Parts Section 33
DRAGBAR HARROW INSTRUCTIONS 2005 Alamo Group Inc. Parts Section 34
CHISEL POINT REMOVABLE PIN KIT NO. 2420479 INSTALLATION INSTRUCTIONS 2005 Alamo Group Inc. Parts Section 35
LIMITED WARRANTY 1. LIMITED WARRANTIES 1.01.M&W warrants for one year from the purchase date to the original non-commercial, governmental, or municipal purchaser ( Purchaser ) and warrants for six months to the original commercial or industrial purchaser ( Purchaser ) that the goods purchased are free from defects in material or workmanship. 1.02.Manufacturer will replace for the Purchaser any part or parts found, upon examination at one of its factories, to be defective under normal use and service due to defects in material or workmanship. 1.03.This limited warranty does not apply to any part of the goods which has been subjected to improper or abnormal use, negligence, alteration, modification, or accident, damaged due to lack of maintenance or use of wrong fuel, oil, or lubricants, or which has served its normal life. This limited warranty does not apply to any part of any internal combustion engine, or expendable items such as blades, shields, guards, or pneumatic tires except as specifically found in your Operator s Manual. 1.04.Except as provided herein, no employee, agent, Dealer, or other person is authorized to give any warranties of any nature on behalf of Manufacturer. 2. REMEDIES AND PROCEDURES. 2.01.This limited warranty is not effective unless the Purchaser returns the Registration and Warranty Form to Manufacturer within 30 days of purchase. 2.02.Purchaser claims must be made in writing to the Authorized Dealer ( Dealer ) from whom Purchaser purchased the goods or an approved Authorized Dealer ( Dealer ) within 30 days after Purchaser learns of the facts on which the claim is based. 2.03.Purchaser is responsible for returning the goods in question to the Dealer. 2.04.If after examining the goods and/or parts in question, Manufacturer finds them to be defective under normal use and service due to defects in material or workmanship, Manufacturer will: (a) (b) Repair or replace the defective goods or part(s) or Reimburse Purchaser for the cost of the part(s) and reasonable labor charges (as determined by Manufacturer) if Purchaser paid for the repair and/or replacement prior to the final determination of applicability of the warranty by Manufacturer. The choice of remedy shall belong to Manufacturer. 2.05.Purchaser is responsible for any labor charges exceeding a reasonable amount as determined by Manufacturer and for returning the goods to the Dealer, whether or not the claim is approved. Purchaser is responsible for the transportation cost for the goods or part(s) from the Dealer to the designated factory. 3. LIMITATION OF LIABILITY. 3.01.MANUFACTURER DISCLAIMS ANY EXPRESS (EXCEPT AS SET FORTH HEREIN) AND IMPLIED WARRANTIES WITH RESPECT TO THE GOODS INCLUDING, BUT NOT LIMITED TO, MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. 3.02.MANUFACTURER MAKES NO WARRANTY AS TO THE DESIGN, CAPABILITY, CAPACITY, OR SUITABILITY FOR USE OF THE GOODS. 3.03.EXCEPT AS PROVIDED HEREIN, MANUFACTURER SHALL HAVE NO LIABILITY OR RESPONSIBILITY TO PURCHASER OR ANY OTHER PERSON OR ENTITY WITH RESPECT TO ANY LIABILITY, LOSS, OR DAMAGE CAUSED OR ALLEGED TO BE CAUSED DIRECTLY OR INDIRECTLY BY THE GOODS INCLUDING, BUT NOT LIMITED TO, ANY INDIRECT, SPECIAL, CONSEQUENTIAL, OR INCIDENTAL DAMAGES RESULTING FROM THE USE OR OPERATION OF THE GOODS OR ANY BREACH OF THIS WARRANTY. NOT WITHSTANDING THE ABOVE LIMITATIONS AND WARRANTIES, MANUFACTURER S LIABILITY HEREUNDER FOR DAMAGES INCURRED BY PURCHASER OR OTHERS SHALL NOT EXCEED THE PRICE OF THE GOODS. 3.04.NO ACTION ARISING OUT OF ANY CLAIMED BREACH OF THIS WARRANTY OR TRANSACTIONS UNDER THIS WARRANTY MAY BE BROUGHT MORE THAN TWO (2) YEARS AFTER THE CAUSE OF ACTION HAS OCCURRED. 4. MISCELLANEOUS. 4.01.Proper Venue for any lawsuits arising from or related to this limited warranty shall be only in Guadalupe County, Texas. 4.02.Manufacturer may waive compliance with any of the terms of this limited warranty, but no waiver of any terms shall be deemed to be a waiver of any other term. 4.03.If any provision of this limited warranty shall violate any applicable law and is held to be unenforceable, then the invalidity of such provision shall not invalidate any other provisions herein. 4.04.Applicable law may provide rights and benefits to purchaser in addition to those provided herein. KEEP FOR YOUR RECORDS M&W ATTENTION: Purchaser should fill in the blanks below for his reference when buying repair parts and/or for proper machine identification when applying for warranty. M&W Implement Model Serial Number Date Purchased Dealer ATTENTION: READ YOUR OPERATOR'S MANUAL M&W An Alamo Group Company 1020 South Sangamon Ave. Gibson City, Illinois 60936 217-784-4261
TO THE OWNER/OPERATOR/DEALER To keep your implement running efficiently and safely, read your manual thoroughly and follow these directions and the Safety Messages in this Manual. The Table of Contents clearly identifies each section where you can easily find the information you need. The OCCUPATIONAL SAFETY AND HEALTH ACT (1928.51 Subpart C) makes these minimum safety requirements of tractor operators: REQUIRED OF THE OWNER: 1. Provide a Roll-Over-Protective Structure that meets the requirements of this Standard; and 2. Provide Seatbelts that meet the requirements of this paragraph of this Standard and SAE J4C; and 3. Ensure that each employee uses such Seatbelt while the tractor is moving; and 4. Ensure that each employee tightens the Seatbelt sufficiently to confine the employee to the protected area provided by the ROPS. REQUIRED OF THE OPERATOR 1. Securely fasten seatbelt if the tractor has a ROPS. 2. Where possible, avoid operating the tractor near ditches, embankments, and holes. 3. Reduce speed when turning, crossing slopes, and on rough, slick, or muddy surfaces. 4. Stay off slopes too steep for safe operation. 5. Watch where you are going - especially at row ends, on roads, and around trees. 6. Do not permit others to ride. 7. Operate the tractor smoothly - no jerky turns, starts, or stops. 8. Hitch only to the drawbar and hitch points recommended by the tractor manufacturer. 9. When the tractor is stopped, set brakes securely and use park lock, if available. Keep children away from danger all day, every day... Equip tractors with rollover protection (ROPS) and keep all machinery guards in place... Please work, drive, play and live each day with care and concern for your safety and that of your family and fellow citizens.
EM 965 1165 & 1465 PL 11/05 Printed U.S.A. P/N 4353P