Automotive Data Solutions Inc. INSTALL GUIDE ADS-TB-CH6 CH6 Available for : ADS-TB Rev. Date: January 06, 0 Doc. No.: ##7984## 0094 Version FRançaise disponible en ligne au www.idatalink.com please visit www.idatalink.com/support for complete product details The brand names and logos found in this guide are property of their respective owners. Automotive Data Solutions Inc. 0 NOTICE: The manufacturer will accept no responsibility for any electrical damage resulting from improper installation of this product, be that either damage to the vehicle itself or to the installed device. This device must be installed by a certified technician. This guide has been written for properly trained technicians; a certain level of skill & knowledge is therefore assumed. Please!review the Installation Guide carefully before beginning any work.
Page of 7 ADS-TB-CH6 Doc. No.: ##7984## 0094 install TYPE SELECTiOn MaKe ModeL plymouth Jeep dodge CHrysLer year InsTaLL Type data IMMoBILIZer Bypass data/mux starter CTrL 300M 99-04 Concorde 99-04 LHS 99-0 Neon 00-05 Pacifica 04-08 PT Cruiser 0-05 Sebring Sedan/Convertible 0-06 Town & Country 0-03 Town & Country 04-07 Voyager 0-03 Caravan/Grand Caravan 0-03 Caravan/Grand Caravan 04-07 Dakota 0-04 Durango 0-03 Intrepid 99-04 Ram Pickup 0-05 SRT 4 03-05 Stratus Sedan 0-06 SX.0 03-05 Grand Cherokee 99-04 Liberty 0-07 TJ 0-06 Wrangler 0-06 Neon 00-0
Page 3 of 7 ADS-TB-CH6 Doc. No.: ##7984## 0094 TYPE - wire CrOSS reference CHArT IGnITIon J850 MaKe ModeL plymouth Jeep dodge CHrysLer year WIre CoLor WIre CoLor 300M 99-04 Blue/White Violet/Yellow Concorde 99-04 Blue/White Violet/Yellow LHS 99-0 Blue/White Violet/Yellow Neon 00-05 Blue/White Violet/Yellow Pacifica 04-08 Pink/Gray White/Violet PT Cruiser 0-05 Blue/Black Violet/Yellow Sebring Sedan/Convertible 0-06 Blue/White Violet/Pink Town & Country 0-07 Pink/White White/Violet Voyager 0-03 Pink/White White/Violet Caravan/Grand Caravan 0-07 Pink/White White/Violet Dakota 0-04 LtGreen/Black Violet/Yellow Durango 0-03 LtGreen/Black Violet/Yellow Intrepid 99-04 Blue/White Violet/Yellow Ram Pickup 0-03 LtGreen/Black Violet/White Ram Pickup 04-05 Pink/Gray White/Violet SRT 4 03-05 Blue/White Violet/Yellow Stratus Sedan 0-06 Blue/White Violet/Pink SX.0 03-05 Blue/White Violet/Yellow Grand Cherokee 99-04 Blue/White Yellow/Violet or Violet/Black Liberty 0-04 Blue Yellow/Violet or Violet/Black Liberty 05-07 Pink/LtGreen White/Violet TJ 0-04 Blue Violet/Yellow TJ 05-06 Pink/White White/Violet Wrangler 0-04 Blue Violet/Yellow Wrangler 05-06 Pink/White White/Violet Neon 00-0 Blue/White Violet/Yellow
Page 4 of 7 ADS-TB-CH6 Doc. No.: ##7984## 0094 TYPE - wiring DIAGRAM SKIM IMMOBILIZER MODULE 3 4 5 6 J850 IGNITION REMOTE STARTER CONNECT ONLY WHEN MUX ND START IS REQUIRED STARTER (+) OUTPUT V (+) GROUND (-) GROUND WHEN RUNNING (-) OUTPUT LEGEND NOT REQUIRED IN (-WAY) NOT REQUIRED IN (-WAY) USE OR HARDWIRE MODE GWR (-) INPUT - BLUE/WHITE (NC) WHITE GROUND - BLACK V (+) - RED WHITE/BLACK - IGNITION IMMO. SIDE WHITE/RED - IGNITION VEHICLE SIDE WHITE (NC) IGNITION (+) INPUT - PINK (NC) PINK/BLACK DATA (J850) - ORANGE (NC) GRAY/YELLOW STARTER (+) INPUT - GRAY/RED (NC) GREEN/YELLOW (NC) GREEN/RED (NC) BLUE/YELLOW (NC) BLUE/RED
Page 5 of 7 ADS-TB-CH6 Doc. No.: ##7984## 0094 TYPE - wiring DIAGRAM RESISTOR BETWEEN 80-0 0HMS VIOLET/BROWN - SWITCH (MUX*) PINK/WHITE - IGNITION (+) YELLOW - STARTER (+) SKIM IMMOBILIZER MODULE 3 4 5 6 USE ISOLATED GROUND WHEN RUNNING FROM REMOTE STARTER TO POWER RELAY DIODE 85 87A 87 86 N400 IGNITION - PINK/WHITE J850 - WHITE/VIOLET 30 REMOTE STARTER V (+) GROUND (-) GROUND WHEN RUNNING (-) OUTPUT LEGEND NOT REQUIRED IN (-WAY) NOT REQUIRED IN (-WAY) USE OR HARDWIRE MODE GWR (-) INPUT - BLUE/WHITE (NC) WHITE GROUND - BLACK V (+) - RED WHITE/BLACK - IGNITION IMMOBILIZER SIDE WHITE/RED - IGNITION VEHICLE SIDE WHITE (NC) IGNITION (+) INPUT - PINK (NC) PINK/BLACK DATA (J850) - ORANGE (NC) GRAY/YELLOW (NC) GRAY/RED (NC) GREEN/YELLOW (NC) GREEN/RED (NC) BLUE/YELLOW (NC) BLUE/RED
Page 6 of 7 ADS-TB-CH6 Doc. No.: ##7984## 0094 Press and release programming button to select installation mode. LED flashes (X) once = LED flashes (X) twice = STANDARD HARDWIRE MODE installation MODULE PrOgrAMMing MODE SELECTiOn! Press and hold programming button until LED turns solid GREEN to register selection. After registration, follow Factory Reset Procedure to change installation mode and restart this procedure. MODULE PrOgrAMMing PrOCEDUrE Insert key into ignition. 5 OFF Turn key to OFF position. ON Turn key to ON position. 6 Remove key. 3 LED will turn solid RED. 7 Module Programming Procedure completed. 4 Wait, it may take up to 0 seconds. LED will turn solid GREEN then will turn OFF.
Page 7 of 7 ADS-TB-CH6 Doc. No.: ##7984## 0094 identify VEHiCLE YEAr Locate the Vehicle Identification Number (VIN) and identify the 0th character. 4 3 A 5 Y N 5 T A L 8 D 5 R 0 X Match the VIN s 0th character to its corresponding year. L > 990 s > 995 y > 000 5 > 005 a > 00 M > 99 T > 996 > 00 6 > 006 B > 0 n > 99 V > 997 > 00 7 > 007 C > 0 p > 993 W > 998 3 > 003 8 > 008 d > 03 r > 994 X > 999 4 > 004 9 > 009 e > 04 Led status Flashing RED diagnostics during programming during remote start WITH IGnITIon off Missing/wrong information from firmware or vehicle Incorrectly programmed Solid RED Waiting for more vehicle information Incorrectly programmed Flashing GREEN Additional steps required to complete programming MODULE DiAgnOSTiCS Correctly programmed and operational Incorrectly programmed or connected Not programmed waiting for more vehicle information False ground when running status from remote starter Solid GREEN then OFF Correctly programmed Reset in progress Reset in progress OFF No activity or already programmed Invalid ground when running status from remote starter At rest and ready for a remote start sequence FACTOrY reset PrOCEDUrE DISCONNECT all connectors from module EXCEPT the black 4-PIN standard or optional data connector. DISCONNECT black 4-PIN standard or optional data connector. 5 6 LED will turn solid red for seconds. RESET COMPLETED. RECONNECT all connectors. 3 4 PRESS AND HOLD programming button while connecting either 4-PIN standard or optional data connector. When LED flashes red, RELEASE programming button. 7! Repeat programming procedure. Failure to follow procedure may result with a DTC or a CHECK ENGINE error message.