HP-4 Recessed with Regressed Visible Flange /Independent Scan QR code for helpful video(s) Step 1 Cutout Dimension Step 2 Step 3 0-10V 5" 7/8" Feed "A" A + 1/4" +/- 1/1 3/4" Nominal Length Add 1/4" to body/row length (A), +/- 1/1 to simplify installation. installed next to support blocking. Remove diffuser and set aside to prevent from getting dirty or damaged. Refer to threads and feed hole locations above before connecting luminaire wires. Step 34 STANDARD INSTALLATION ALTERNATE OPTION FROM TOP Step 5 Conduit Conduit Plate (Gray) (Purple) Feed Hole Remove jam nut from conduit then insert wires and connector through feed hole. NOTE: Purple and gray wires are for Low Voltage Control. Remove screw (provided) to open trap door and then insert luminaire into ceiling. Align luminaire within rough opening in drywall and 1/4"-20 threaded rod. 1 2017 FINELITE, INC. ALL RIGHTS RESERVED. Form 98181 V2. 04/17
HP-4 Recessed with Regressed Visible Flange /Independent Step 6 (provided) Connector 1/4"-20 Threaded Rod 1/4"-20 Nut ALTERNATE MOUNTING OPTION Screw 1/4"-20 Washer 1/4"-20 Nut Screw Secure to structure by installing 1/4" washers and 1/4"-20 nuts onto 1/4"-20 threaded rod. ALTERNATE MOUNTING OPTION: Install screw through mounting hole into proper structurally supported blocking. Step 7 Step 8 Step 9 Make wire connections and secure trap door with screw (provided). On opposite end of luminaire, fold trap door down. Install 1/4"-20 nut and 1/4" washer onto 1/4"-20 threaded rod or use ALTERNATE MOUNTING OPTION in step 6. Replace trap door and fasten with screws (provided). Reinstall diffuser and turn power on. NOTE: If part of a longer run, diffuser will be reinstalled back into original luminaire section as lengths vary. 2 2017 FINELITE, INC. ALL RIGHTS RESERVED. Form 98181 V2. 04/17
HP-4 Recessed with Regressed Visible Flange Scan QR code for helpful video(s) Step 1 Cutout Dimension Step 2 Step 3 0-10V 5" 7/8" Feed A A + 1/4" +/- 1/1 3/4" Nominal Length Add 1/4" to body/row length (A), +/- 1/1 to simplify installation. needs to be installed next to support blocking. Remove diffuser and set aside to prevent from getting dirty or damaged. NOTE: If part of a longer run, diffuser will be reinstalled back into original luminaire section as lengths vary. Refer to threads and feed hole locations above before connecting luminaire wires. Step 34 STANDARD INSTALLATION ALTERNATE OPTION FROM TOP Step 5 Conduit Conduit Plate Remove jam nut from conduit then insert wires and connector through feed hole. (Gray) (Purple) Feed Hole Remove screw (provided) to open trap door and then insert luminaire into ceiling. Align luminaire within rough opening in drywall and 1/4"-20 threaded rod. 1
HP-4 Recessed with Regressed Visible Flange Step 6 (provided) Connector 1/4"-20 Threaded Rod ALTERNATE MOUNTING OPTION 1/4"-20 Nut Screw 1/4"-20 Washer 1/4"-20 Nut Screw Secure to structure by installing 1/4" washers and 1/4"-20 nuts onto 1/4"-20 threaded rod. ALTERNATE MOUNTING OPTION: Install screw through mounting hole into proper structurally supported blocking. Step 7 Step 8 Step 9 Joiner Plate Make wire connections and secure trap door with screw (provided). On opposite end of luminaire, fold trap door down. Install 1/4"-20 nut and 1/4" washer onto 1/4"-20 threaded rod or use ALTERNATE MOUNTING OPTION in step 6. Replace trap door and fasten with screws (provided). Plug-Together Wiring Connect plug-together wiring. Slide joiner luminaire against starter luminaire Be careful not to damage any wiring. 2
HP-4 Recessed with Regressed Visible Flange Step 10 IMPORTANT STEP #8-18 x 1/2" Combo Hex Screw (provided) End Brackets Step 11 Joiner 1/4"-20 Nut 1/4"-20 Washer IMPORTANT STEP: Install the two #8-18 x 1/2" combo hex screws (provided) into end bracket as shown. Screws can be installed from the left or right. CAUTION: Do not over-tighten. On opposite end of luminaire, fold trap door down. Install 1/4" washer and 1/4"-20 nut onto 1/4"-20 threaded rod or use ALTERNATE MOUNTING OPTION in step 6. Replace trap door and fasten with Step 12 s Reinstall diffusers to starter and joiner/enders and turn power on to luminaire. NOTE: If part of a longer run, diffuser will be reinstalled back into original luminaire section as lengths vary. 3