Replacement parts to fit MASSEY FERGUSON CONTENTS IMPORTANT ORDERING INFORMATION

CONTENTS SECTION 1 SECTION 2 SECTION 3 SECTION 4 SECTION 5 SECTION 6 SECTION 7 SECTION 8 SECTION 9 ENGINES...MF-1-1 through MF-1-72 ENGINE SYSTEMS...MF-2-73 through MF-2-97 ELECTRICAL...MF-3-97 through MF-3-107 POWER TRAIN...MF-4-108 through MF-4-126 WHEELS AND ALES...MF-5-127 through MF-5-140 HITCH AND HYDRAULICS...MF-6-141 through MF-6-165 FORAGE AND HARVESTING...MF-7-166 through MF-7-176 IMPLEMENTS AND BEARINGS...MF-8-177 through MF-8-182 MISCELLANEOUS...MF-9-183 through MF-9-199 IMPORTANT ORDERING INFORMATION PART NUMBERS OEM numbers are used only for identification. All parts shown in this catalog are represented and sold as replacement parts only. Engine Kits To make ordering easier, we have four types of engine kits available. (1) Complete Engine Overhaul Kit (available for a limited number of tractor models) (2) Engine Overhaul Kit (EOK) (3) Basic Engine Kit (BEK) (4) Basic In-Frame Kit (BIF) EOKs and BEKs are available for most of the tractor models that we service with engine parts. Section 1 pages list the contents and also parts that can be ordered individually. Piston & Ring Sets For ease of ordering, our PK kits contain pistons, piston pins, pin retainers, piston rings, cylinder sleeves & sleeve seals(where noted) for one complete engine. Our PRS kits contain piston rings for one complete engine. Unless otherwise noted, we make no representation that our piston rings fit pistons available from other suppliers. We are aware of some interchangeability of tractor engine parts for other Massey Ferguson applications (combine, forklifts, industrial tractors & power plants); some of these applications are listed on the engine pages, otherwise no attempt is made to suggest other applications. Alphabetical Index Follows MF-I

ALPHABETICAL INDE A Actuator, Brake, 109 Adapter, Engine Block Heater, 92 Air Cleaner Bowl, 80 Air Cleaner Cap, 82 Air Cleaner Hose, 82 Air Cleaner Oil Cup, 82 Air Filter, 81 Alignment Tool, Clutch, 113 Alternator, 105 Bearing, 106 Brush, 106 Conversion Kit, 105 Diode Trio, 106 Pulley, 106 Repair Kit, 106 Ammeter, 106 Anchor Pins, 150 Arm, Steering, 134 Arm, Three Point Lift, 142, 144, 147 Armrest, Seat, 199 Auger Finger, 174 Auger Finger Guide, 174 Axle Bearing, Front Spindle, 137 Bearing, Spindle Thrust, 137 Bearings, Front, 136, 138 Bolt, 131 Bushing, Front Pivot, 131 Bushing, Front Spindle, 137 Front, 135 Gasket, Rear Housing, 124 Hub, 139 Knee, Front, 135 Pin, Front Pivot, 131 Seal, Rear, 124 Seals, 122, 124, 180 Seals, Front, 138 Seals, Front Hub, 138 Sleeve, Rear Speedi, 124 Sleeve, Wear, Front, 136, 139 Spindle, Front, 135 to 136 Tie Rod Ends, Front, 131 to 132 B Backrest, Seat, 199 Bale Counter, 172 Baler Parts Bearing, Wire Guide, 171 Bolt, Bale Chamber Shear Blade, 171 Counter, Bale, 172 Shearbolt, 171 Switch, Twine Tie, 171 Teeth, Pickup, 170 Ball Bearing, 177 Ball, Disc Brake, 109 Ball, Lift Arm, 144 to 145 Battery Bolt, 104 Cable, 104 Door, 190 Ground Strap, 104 Bearings Alternator, 106 Ball, 177 Carrier, Clutch Release, 117 Clutch, Pilot, 117 Clutch, Release, 117 Combine, 172, 178 Disc Harrow, 179 Disc Harrow Wheel Kit, 180 Flanges, 179 Generator, 104 Guide, Baler Wire, 171 Mower, 170 PTO Shaft, 125 to 126 Pump, Hydraulic Lift, 155 Shaft, Steering, 127 Sickle Head, 168 Spindle, Thrust, 137 Straw Walker, 175 Tapered Cups & Cones, 123 to 124, 127, 170, 180 Thrust, Spindle, 137 Thrust, Steering Gear, 127 Transmission, 119, 123 to 124 Wheel, Disc, 180 Wheel, Front, 136, 138 Wheel, Gauge, 177 Belts Alternator, 86 Combine, 86, 176 Fan, 86 Generator, 86 Mower, 170 Block Heater, 92 Block, Hydraulic Pump Cam, 153 to 154 Blower Assembly Massey Ferguson, 187 Blower Motor Massey Ferguson, 187 Blower Switch Massey Ferguson, 184 Bolt Axle, 131 Bale Chamber Shear Blade, 171 Battery, 104 Clutch Release Lever, 113 Differential Ring Gear, 121 Front Wheel, 140 Guard, 168 MF-II

Bolt (continued) Hydraulic Pump Drive, 157 Sickle Head, 168 Swinging Drawbar, 152 Wheel, 139 to 140 Bowl, Air Cleaner, 80 Bracket Bumper, 187 Hood Side Panel, 190 Three Point Stabilizer, 149 to 150 Valve Handle, 163 Brakes Actuators, 109 Ball, Disc, 109 Cable, 110 Cylinder, 108 Discs, 109 Drum, 108 Rod, 110 Seal, Rod, 110 Shoes, 108 Spring, 110 Brush, Alternator, 106 Brush, Generator, 104 Bulb, Light, 106 to 107 Bumper Bracket, 187 Bumper, Front, 187 Bushing Carburetor Throttle Shaft, 74 Clutch Shaft, 118 Combine Slip Clutch, 175 Corn Head, 172 Front Axle Pivot, 131 Hydraulic Pump, 153 Hydraulic Pump Drive Plate, 158 Link Pin Adaptor, 145, 148 Spindle, 137 Steering Shaft, 128 Sway Chain Eyebolt, 151 Three Point Lift Shaft, 142 Three Point Stabilizer, 151 C Cab Floormat, 193 Cable, Battery, 104 Cable, Brake, 110 Cable, Tachometer, 84 Cam & Weight, Distributor, 97 Camshaft Gear, 71 Camshaft, Engine, 71 Cap, Air Cleaner, 82 Cap Distributor, 97 to 98 Fuel Tank, 76 Hub, 138 Oil Filler, 83 Radiator, 88 Steering Wheel, 127 Carburetor, 73 Bushing, Throttle Shaft, 74 Elbow, Inlet, 75 Float, 75 Kits, 73 to 74 Carrier, Clutch Release Bearing, 117 Chain Combine Drive, 175 Connector Links, 173 Gathering, Corn Head, 173 Half Links, 173 Offset Links, 173 Clamp Exhaust, 94 Hydraulic Coupler, 159 Rear Wheel, 140 Clevis, Lift Arm Stay Chain, 151 Clevis, Swinging Drawbar Mount, 151 Clutch Alignment Tool, 113 Bearing, Pilot, 117 Bearing, Release, 117 Bolt, Release Lever, 113 Bushing, Combine Slip Clutch, 175 Bushing, Shaft, 118 Carrier, Bearing, 117 Cover, 111, 115 Disc, 112, 116, 119 Disc, PTO, 112 Disc, Slip Clutch, 171 Kits, Complete, 111 Lever, Release, 113, 115 Link, Release Lever, 113 Nut, Release Lever, 113 Pin, 113 Pin, Release Lever Pivot, 113 Pin, Release Lever Retaining, 113 Plate, Friction, 121 Pressure Plate, 111, 116 Slip, Combine, 175 Spring, 113, 115 to 116, 118 Washer, Pressure Plate Spring, 113 Coils, Ignition, 98 Combine Parts Bearing, Straw Walker, 175 Bearings, 172, 178 Belts, 86, 176 Blades, Sickle, 166 Bushing, Slip Clutch, 175 Chain, Corn Head Gathering, 173 Chain, Drive, 175 Clutch, Slip, 175 Finger, Auger, 174 Flute, Corn Head, 172 Guards, Sickle, 169 Guide, Auger Finger, 174 Holder, Auger Finger, 174 Idler, Chain, 175 MF-III

Combine Parts (continued) Idler, Wood Block Chain, 175 Knife, Straw Chopper, 174 Paddle, 174 Rivet, Sickle, 167 Seal, Engine Air Intake, 173 Section, Sickle, 166 to 167 Spacer, Corn Head, 172 Teeth, Pickup, 170 Tine, Pickup Reel, 173 Compressor Massey Ferguson, 183 Condenser, Distributor, 97 to 98 Cone, Hood Nose, 188 Connector, Sickle Head, 168 Cooling Systems Caps, Radiator, 88 Drain, Radiator, 88 Fan, Blade, 88 Gaskets, 86 Hoses, 90 to 91 Kits, Water Pumps, 86 Pulley, Water Pumps, 86 Radiators, 89 Sender, Water Temperature, 84 Thermostats, 90 Water Pumps, 85 Counter, Bale, 172 Coupler Clamp, Hydraulic, 159 Female Hydraulic, 159 Hydraulic Pump Drive, 157 Male Hydraulic, 159 Cover, Distributor Dust, 98 Cover, PTO, 125 Crankshaft Gear, 71 Crankshaft, Engine, 71 Cuff, Lift Arm, 145 Cultivator Gauge Wheel, 177 Cultivator Sweep Washer, 177 Cup, Air Cleaner Oil, 82 Cut-out, Generator, 104 Cylinder Head, Engine, 72 Cylinder Ball Joint End, 129 Brakes, 108 Hydraulic Three Point Lift, 143 Side Link, 165 Steering, 128 Top Link, 165 D Decals, 197 Deflector, Ear Corn, 173 Detent, Hydraulic Valve, 163 Differential Bolt, Ring Gear, 121 Coupler, Pinion Shaft, 121 to 122 Differential (continued) Nut, Ring Gear, 121 Pinion, 123 Resin Kit, 121 Disc Bearings, 179 Brake, 109 Clutch, 112, 116, 119 Clutch, Slip, 171 PTO Clutch, 112, 116 PTO Friction, 119 Quadrant Friction Plate, 143 Distributor, 97 Caps, 97 to 98 Coil, 98 Dust Cover, 98 Rotor, 97 to 98 Door, Battery, 190 Drag Link Ends, 131 to 132 Drain Cock, Radiator, 88 Drawbar Bolt, Swinging, 152 Clevis Mount, 151 Drawbar, 151 Hanger, 151 Pin, 151 Pivot Pin, 152 Stay Arm, 151 Three Point, 151 Drum, Brake, 108 Dust Cap, Wheel, 138 E Ear Corn Deflector, 173 Elbow, Exhaust, 92 Electrical Adapter, Block Heater, 92 Alternators, 105 Ammeter, 106 Bolt, Battery, 104 Brush, Alternators, 106 Brush, Generator, 104 Bulb, Light, 106 to 107 Cables, Battery, 104 Cables, Ground Strap, 104 Cam & Weight, Distributor, 97 Cap, Distributor, 97 to 98 Clip, Neutral Safety Switch, 101 Coils, Ignition, 98 Condenser, 97 to 98 Cover, Distributor Dust, 98 Cut-out, Generator, 104 Diode, Alternator, 106 Distributor, 97 Drive, Starters, 103 Electronic Ignition Kit, 98 Heater, Engine, 92 Heater, Engine Manifold, 91 MF-IV

Electrical (continued) Holder, Fuse, 106 Housing, Starter Drive, 103 Key, Ignition Switch, 100 Kit, Alternator Conversion, 105 Kit, Alternator Repair, 106 Kit, Tune-up, 98 to 99 Light, Warning, 107 Points, 97 to 98 Pulley, Alternator, 106 Rectifier, Alternators, 106 Regulator, Voltage, 104, 106 Rotor, Distributor, 97 to 98 Sender, Fuel Tank, 76 Solenoid, Starter, 102 Spark Plugs, 98 Starter Drive, 103 Starters, 102 Switch, Ignition, 100 Switch, Light, 101 Switch, Neutral Safety, 101 Switch, Oil Pressure, 83 Switch, Water Temperature Sending Unit, 84 Wires, Spark Plug, 97 End Lift Arm, 144 to 145 Lift Arm Repair, 144 Top Link, 147 Engines Belts, 86 Camshaft, 71 Caps, Fuel Tank, 76 Caps, Oil Filler, 83 Caps, Radiator, 88 Clamps, Mufflers, 94 Crankshaft, 71 Elbow, Exhuast, 92 Fan, Cooling, 88 Filters, Air, 80 to 81 Filters, Fuel, 80 Filters, Oil, 82 Gaskets, Manifold, 93 Gauge, Oil Pressure, 83 Gauge, Water Temperature, 84 Gear, Camshaft, 71 Gear, Crankshaft, 71 Governor, 83 Head, Cylinder, 72 Heater, Block, 92 Heater, Manifold, 91 Kit, See page I to V for complete application listing, 1, 3 to 70 Manifolds, 92 Mufflers, 93 to 96 Oil Level Indicator, 83 Pulley, Water, Repair, 86 Pump Repair Kit, Oil, 72 Pump, Oil, 72 Pumps, Water, 85 Engines (continued) Pumps, Water, Repair Kit, 86 Seal, Combine Air Intake, 173 Thermostat, 90 Exhaust System Caps, Rain, 94 Clamps, 94 Elbow, 92 Gaskets, Manifold, 93 Heater, Manifold, 91 Manifolds, 92 Mufflers, 93 to 96 Rain Caps, 94 Expansion Valve Massey Ferguson, 186 Eyebolt, Lift Arm Sway Chain, 151 Eyebolt, Sway Chain, 151 F Fan, Cooling, 88 Fender, 190, 192 Filters Air, 80 to 81 Fuel, 80 Oil, Engine, 82 Oil, Hydraulic, 119, 121, 158 to 159 Power Steering, 130 Finger, Auger, 174 Flange, Hydraulic Pump Drive, 157 Flangettes, Bearing, 179 Float, Carburetor, 75 Floormat, 193 Flute, Corn Head, 172 Flywheel Ring Gear, 103 Fork, Leveling Shaft, Three Point, 142 Fork, Three Point Leveling, 141 Fuel Gauge, 76 Fuel Injector Pumps, 78 Fuel Systems Bushing, Carburetor Throttle Shaft, 74 Caps, Fuel Tank, 76 Carburetors, 73 Filter, Air, 80 to 81 Filter, Fuel, 80 Floats, Carburetor, 75 Gauge, 76 Injector Nozzle, 79 Injector Pumps, 78 Kits, Carburetors, 73 to 74 Needle & Seat, 75 Nozzle, Injectors, 79 Pumps, Lift, 77 Sediment Bowl Assembly, 75 Sender, Tank, 76 Shut-Off, Tank, 76 Strainer, Carburetor Inlet, 75 Tank Webbing, 76 Valve, Float, 75 MF-V

Fuel Systems (continued) Valve, Shut-off, 75 Fuse Holder, 106 Fuse, Limiter Massey Ferguson, 185 G Gas Struts, 194 Gaskets Axle, Rear Housing, 124 Exhaust, 93 Hydraulic Lift Cover, 143 Hydraulic Pump Base, 143 Hydraulic Pump Valve Chamber, 143 Hydraulic Quadrant, 143 Transmission, 119, 143, 153 Water Outlet, 86 Gauge Wheel, 177 Gauges Ammeter, 106 Cable, Tachometer, 84 Fuel, 76 Fuel Tank Sender, 76 Oil Level Indicator, Engine, 83 Oil Level Indicator, Hydraulic, 152 Pressure, Engine Oil, 83 Tachometer, 84 Temperature, Water, 84 Gear Camshaft, Engine, 71 Crankshaft, Engine, 71 Lift Leveling Box, 141 Shift Knob, 118 Starter Ring, 103 Generator Bearing, 104 Brush, 104 Cut-out, 104 Governor, 83 Grassboard, Sickle Mower, 170 Grill, 187, 189 Grommet, Steering Column, 127 Guard Bolt, 168 Guard, Sickle, 169 Guide, Auger Finger, 174 H Handle Kit, Valve, 162 Handle, Hydraulic Valve, 162 to 163 Hanger, Swinging Drawbar, 151 Hardener, Paint, 196 Head Connector, Seals, 168 Head, Engine Cylinder, 72 Head, Sickle, 168 Heater Adapter, Engine Block, 92 Heater, Engine Block, 92 Hitch Pins, 152 Hold Down, Sickle Knife, 169 Holder, Auger Finger, 174 Hood Decals, 197 Engine, 190 Latch, 104, 190 Nose Cone, 188 Side Panel, 190 Trim, 189 Hose Air Cleaner, 82 Hydraulic Assemblies, 161 Radiator, 90 to 91 Housing, PTO Pinion Shaft, 122 Hub Cap, 138 Hydraulic Bearing, Lift Pump, 155 Block, Pump Cam, 153 to 154 Bolt, Pump Drive, 157 Bracket, Valve Handle, 163 Bushing, Pump, 153 Bushing, Pump Drive Plate, 158 Chamber Kit, Pump, 153 Clamp, Coupler, 159 Coupler Kit, 160 Coupler, Pump Drive, 157 Couplers, Female, 159 Cylinder, Side Link, 165 Cylinder, Three Point Lift, 143 Cylinder, Top Link, 165 Detent, Valve, 163 Disc, Quadrant Friction Plate, 143 Filter, 119, 121, 158 to 159 Flange, Pump Drive, 157 Gasket, Lift Cover, 143 Gasket, Pump Base, 143 Gasket, Pump Valve Chamber, 143 Gasket, Quadrant, 143 Handle, 162 to 163 Handle Kit, Valve, 162 Hose Assembly, 161 Kit, Control Valve, 155 Kit, Cylinder Seal, 159 Kit, Pump Repair, 153 to 154 Kit, Top and Side Link Cylinder Seal, 165 Kit, Valve Spool Return, 163 Kits, Valve, 160 to 161, 163 Knob, Valve Handle, 162 Nut, Pump Drive, 157 O-Rings, 119, 152, 154 to 156 Oil Dipstick, 152 Piston, Lift, 153, 155 Piston, Pump, 155 Piston, Three Point Lift, 143 Plate, Pump Drive, 158 Plug, Coupler Dust, 159 Power Beyond Plug, Valve, 163 Pumps, 153, 156 Ring, Three Point Lift Piston, 155 MF-VI

Hydraulic (continued) Rings, Piston, 143 Seal Kit, Valve, 163 Seal, Cylinder, 159, 165 Shaft, Pump, 158 Shaft, Three Point Lift, 142 Stop, Quadrant Lever, 144 Tips, Male, 159 Valve, 162 Valve, Isolator, 160 Valve, Lift Cylinder Pressure Relief, 156 Valve, Pressure Relief, 156 Valve, Pump Chamber Assembly, 154 Valve, Pump Control, 155 Valve, Pump Releif, 156 I Ignition Kit, Electronic, 98 Ignition Switch, 100 Injector Nozzle Tip, 79 Injector Nozzle, Fuel, 79 Injector Pumps, Fuel, 78 K Key, Ignition Switch, 100 Kits Alternator Conversion, 105 Clutch, 111 Coupler, Hydraulic, 160 Cylinder Seal, 159 Electronic Ignition, 98 Engine, See page I to V for complete application listing, 1, 3 to 70 Hydraulic Lift Cover Repair, 143 Hydraulic Pump Repair, 153 to 154 Hydraulic Pump, Chamber, 154 Hydraulic Remote Valve, 159 Ignition Tune-Up, 98 to 99 Over-Running Coupler Repair, 126 Pump Control Valve, 155 Pump Seal, 130 Seal, Steering Cylinder, 128 Steering Seal, 129 to 130 Top and Side Link Cylinder Seal, 165 Valve Spool Return, Hydraulic, 163 Valve, Hydraulic, 160 to 161, 163 Knife Clip, 169 Knife, Straw Chopper, 174 Knob, Hydraulic Valve Handle, 162 Knob, Transmission Gear Shift, 118 L Latch, Hood, 104, 190 Leveling Box Assembly, Three Point, 141 Lever, Clutch Release, 113, 115 Lift Arm End, Three Point, 144 to 145 Lift Arm, Three Point, 142, 144, 147 Lift Cover Repair Kit, 143 Light, Warning, 107 Light Bulb, 106 to 107 Switch, 101 Limiter Fuse Massey Ferguson, 185 Linch Pin, 149, 152 Link, Clutch Release Lever, 113 Link, Three Point Lift, 141 Links, Chain Connector, 173 Links, Offset Chain Connector, 173 Lower Link Pins, 150 Lug Bolt, 139 to 140 M Manifold, 92 Massey Ferguson Blower Assembly, 187 Blower Motor, 187 Blower Switch, 184 Compressor, 183 Expansion Valve, 186 Limiter Fuse, 185 Pressure Switch, 184 Receiver Drier, 185 Thermostatic Switch, 184 Mower Parts Bearings, 170 Belts, 170 Bolt, Guard, 168 Bolt, Sickle Head, 168 Clip, Knife, 169 Connector, Sickle Head, 168 Grassboard, 170 Guards, Disc Mower, 169 Guards, Sickle Mower, 169 Head, Sickle, 168 Hold Down, Knife, 169 Knives, Sickle, 166 Nut, Sickle Guard, 168 Pitman Wood, 169 Plate, Wear, 168 to 169 Rivet, Sickle, 167 Section, Sickle, 166 to 167 Spacer, Sickle Head, 168 Strip, Hold Down Wear, 169 Vise, Sickle Section Rivet, 168 Washer, Sickle Guard, 168 Mufflers, 93 to 96 N Needle & Seat, Carburetor, 75 Nozzle, Fuel Injector, 79 Nozzle, Injector, 79 Nut Clutch Release Lever, 113 Differential Ring Gear, 121 Front Wheel, 139 Hydraulic Pump Drive, 157 MF-VII

Nut (continued) Sickle Guard, 168 Stabilizer Pin, 149, 151 Wheel, 140 Wheel Clamp Lock, 138 O O-Rings, 119, 152, 154 to 156 Oil Cup, Air Cleaner, 82 Oil Cap, Filler, 83 Engine Pump Repair Kit, 72 Filter, Engine, 82 Gauge, Pressure, 83 Indicator, Level, 83, 152 Pump, Engine, 72 Switch, Pressure, 83 Over-Running Coupler Repair, 126 P Paddle, Combine, 174 Paint Aluminum, 195 Black, 195 Hardener, 196 OEM Colors, 195 Primer, 196 White, 195 Panel, Hood Side, 190 Pickup Teeth, Baler, 170 Pin Anchor, 150 Clutch, 113 Clutch Release Lever Pivot, 113 Clutch Release Lever Retaining, 113 Drawbar, 151 Front Axle Pivot, 131 Hitch, 152 Linch, 149, 152 Lower Link, 150 Stabilizer, 144, 149 to 151 Swinging Drawbar Pivot, 152 Top Link, 150 Piston, Hydraulic Lift, 153, 155 Piston, Three Point Lift, 143 Pitman Wood, 169 Plate, Hydraulic Pump Drive, 158 Plate, Sickle Wear, 168 to 169 Plug, Hydraulic Coupler Dust, 159 Points, Distributor, 97 to 98 Power Beyond Plug, Hydraulic Valve, 163 Power Steering Plate, 130 Pressure Plate, 111, 116 Pressure Switch Massey Ferguson, 184 Primer, 196 PTO Bearing, Shaft, 125 to 126 PTO (continued) Clutch Disc, 112, 116 Coupler, Over-Running, 126 Cover, 125 Disc, Clutch, 112 Housing, Pinion Shaft, 122 Kit, Over-Running Coupler Repair, 126 Plate, Clutch, 119 Shaft, Conversion, 125 Shaft, Pinion, 122 Sleeve, Shaft Retainer, 125 Pulley, Alternator, 106 Pulley, Water Pump, 86 Pump Control Valve, 155 Pumps Bushing, Hydraulic Drive Plate, 158 Cam Block, Hydraulic, 153 to 154 Chamber Kit, Hydraulic, 153 Coupler, Hydraulic Drive, 157 Flange, Hydraulic Drive, 157 Fuel Lift, 77 Hydraulic, 153, 156 Hydraulic Chamber Repair, 154 Hydraulic Repair Kit, 153 Kit, Hydraulic Repair, 154 Oil, Engine, 72 Plate, Hydraulic Drive, 158 Repair Kit, Engine Oil, 72 Shaft, Hydraulic, 158 Steering, Power, 129 Valve, Hydraulic Chamber Assembly, 154 Water, Engine, 85 Water, Repair Kit, 86 R Radiator, 89 Cap, 88 Drain, 88 Hose, 90 to 91 Rain Cap, Exhaust, 94 Receiver Drier Massey Ferguson, 185 Rectifier, Alternator, 106 Resin Kit, Differential, 121 Rim Clamp, Rear, 140 Front Wheel, 139 Rear Wheel, 140 Ring Gear, Starter, 103 Rings, Hydraulic Lift Piston, 143 Rings, Three Point Lift Piston, 143, 155 Rivet, Sickle, 167 Rod and Yoke, Three Point Leveling, 142 Rod End, Steering Cylinder, 128 Rod, Brake, 110 Rod, Lift Leveling, 141 Rotor, Distributor, 97 to 98 MF-VIII

S Screw, Power Adjust Stop, 140 Seal Kit, Steering Cylinder, 128 Seal, Front Axle, 138 Seals, 119, 122, 124 to 125, 136, 138 Axle, Rear, 124 Brake Rod, 110 Head Connector, 168 Sleeve, Implement Wheel, 180 Sleeve, Wear, Front Axle, 136, 139 Valve, Hydraulic, 163 Seat Armrest, 199 Backrest, 199 Cover, Cushion, 198 to 199 Cushion, 198 to 199 Inlay, Cushion, 198 Riser, 199 Seat Assembly, 198 Section, Sickle, 166 to 167 Sediment Bowl Assembly, 75 Sending Unit, Fuel Tank, 76 Shaft Conversion, PTO, 125 Hydraulic Pump, 158 Leveling Three Point, 141 to 142 Lift Arm Pivot, 144 PTO, 125 PTO Pinion, 122 Steering, 127 Three Point Lift, 142 Shearbolt, 171 Sheet Metal Bracket, Bumper, 187 Bracket, Side Panel, 190 Bumpers, 187 Cone, Hood Nose, 188 Door, Battery, 190 Fender, 190, 192 Grill, 187, 189 Hood, 190 Latch, Hood, 104, 190 Panel, Side, 190 Trim, Hood, 189 Shoe, Brake, 108 Shut-Off, Fuel, 76 Sickle Guard Bolt, 168 Guard Nut, 168 Guard Washer, 168 Head, 168 Head Bearing, 168 Head Bolt, 168 Head Connector, 168 Head Spacer, 168 Hold Down Wear Strip, 169 Knife Assembly, 166 Knife Clip, 169 Sickle (continued) Pitman Wood, 169 Repair Vise, 168 Rivets, 167 Section, 166 to 167 Wear Plate, 168 to 169 Sleeve, PTO Shaft Retainer, 125 Slip Clutch Disc, 171 Slip Clutch, Combine, 175 Solenoid, Starter, 102 Spacer, Sickle Head, 168 Spark Plug Wires, 97 Spark Plugs, 98 Spindle, Front Axle, 135 to 136 Spring Brakes, 110 Clutch, 113, 115 to 116, 118 Multi-Power Piston Return, 119 Sprocket, Chain Idler, 175 Stabilizer Pins, 149 to 150 Stabilizer, Three Point Hitch, 149 to 150 Starter, 102 Drive, 103 Housing, Drive, 103 Ring Gear, 103 Switch, Neutral Safety, 101 Starter Solenoid, 102 Starter Drive, 103 Housing, Drive, 103 Ring Gear, 103 Switch, Neutral Safety, 101 Steering Arm, 134 Axle, Front, 135 Bearing, Steering Gear Thrust, 127 Bushing, Shaft, 128 Bushing, Spindle, 137 Cap, Steering Wheel, 127 Cylinder, 128 Drag Link End, 131 to 132 End, Power Steering Cylinder, 129 Filters, 130 Grommet, Column, 127 Kit, Cylinder, 128 Kit, Pump Seal, 130 Plate, Power Steering, 130 Pump Seal Kit, 130 Pumps, 129 Rod End, Cylinder, 128 Seal Kit, 129 to 130 Shaft, Steering Wheel, 127 Spindle, Front, 135 to 136 Tee, Line, 131 Tie Rod, 132 Tie Rod Ends, 131 to 132 Wheel, 127 Stop, Hydraulic Quadrant Stop, 144 MF-I

Stop, Power Adjust Wheel, 140 Strainer, Fuel, 75 Strip, Sickle Hold Down Wear, 169 Struts, Gas, 194 Sway Chain, Lift Arm, 151 Swinging Drawbar, 151 Switch Activator, Tine Tie, 171 Clip, Neutral Safety, 101 Ignition, 100 Light, 101 Neutral Safety, 101 Oil Pressure, 83 Water Temperature Sending Unit, 84 Switches Blower, Massey Ferguson, 184 Pressure, Massey Ferguson, 184 Thermostatic, Massey Ferguson, 184 T Tachometer, 84 Tachometer Cable, 84 Tank Webbing, Fuel, 76 Tee, Steering Line, 131 Teeth, Baler Pickup, 170 Teeth, Combine Pickup, 170 Thermostatic Switch Massey Ferguson, 184 Thermostats, 90 Three Point Hitch Arm, Lift, 142, 144, 147 Ball, Lift Arm, 144 to 145 Bracket, Stabilizer, 149 to 150 Bushing, Lift Shaft, 142 Bushing, Link Pin Adaptor, 145, 148 Bushing, Stabilizer, 151 Bushing, Sway Chain Eyebolt, 151 Clevis, Stay Chain, 151 Cuff, Lift Arm, 145 Cylinder, Hydraulic Lift, 143 Drawbar, 151 End, Lift Arm, 144 to 145 End, Lift Arm Repair, 144 End, Top Link, 146 to 148 Eyebolt, Sway Chain, 151 Fork, Leveling, 141 to 142 Gear, Leveling Box, 141 Kit, Lift Cover Repair, 143 Leveling Box Assembly, 141 Link, 141 Nut, Stabilizer Pin, 149, 151 Pin, Anchor, 150 Pin, Lower Link, 150 Pin, Stabilizer, 144, 149 to 151 Pin, Top Link, 150 Piston, Hydraulic Lift, 153, 155 Piston, Lift, 143 Ring, Lift Piston, 155 Three Point Hitch (continued) Rings, Lift Piston, 143 Rod and Yoke, Leveling, 142 Rod, Leveling, 141 Seal, Top and Side Link Cylinder, 165 Shaft, Leveling, 141 to 142 Shaft, Lift, 142 Shaft, Lift Arm Pivot, 144 Stabilizer, 149 to 150 Stay, Drawbar, 151 Sway Chain, 151 Top Link, 146 to 147 Washer, Stabilizer Lock, 149 Tie Rod Ends, 131 to 132 Tine, Pickup Reel, 170, 173 Tire, Cultivator Gauge Wheel, 177 Tool, Clutch Alignment, 113 Tools, Sickle Repair, 168 Top Link End, 146 to 148 Top Link Pins, 150 Top Link, Three Point, 146 to 147 Transmission Bearing, 123 to 124 Bearing, PTO Shaft, 125 to 126 Bearings, 119 Bolt, Differential Ring Gear, 121 Coupler, Differential, 121 to 122 Cover, Clutch, 111 Cover, PTO, 125 Disc, Clutch, 112, 116, 119 Disc, Multi-Power, 119 Disc, PTO, 119 Disc, PTO Clutch, 112, 116 Gaskets, 119, 143, 153 Kits, Clutch, 111 Knob, Gear Shift, 118 Nut, Differential Ring Gear, 121 Pinion, Differential, 123 Plate, Friction, 121 Plate, PTO Clutch, 119 Pressure Plate, Clutch, 111 Resin Kit, Differential, 121 Ring Gear, Differential, 123 Shaft, PTO, 125 Shaft, PTO Conversion, 125 Shaft, PTO Pinion, 122 Spring, Multi-Power Piston Return, 119 Trim, Hood, 189 U Upholstery, Floormat, 193 V Valve, Expansion Massey Ferguson, 186 Valve Hydraulic, 162 Hydraulic Lift Cylinder Pressure Relief, 156 MF-

Valve (continued) Hydraulic Pressure Relief Valve, 156 Hydraulic Pump Control, 155 Hydraulic Pump Relief, 156 Isolator, 160 Pump Control, 155 Vise, Sickle Section Rivet, 168 Voltage Regulator, 104, 106 W Warning Light, 107 Washer Guard, Sickle, 168 Lock, Stabilizer Pin, 149 Spring, Pressure Plate, 113 Sweep, Cultivator, 177 Water Pump Repair Kit, 86 Water Pumps, 85 Water Temperature Gauge, 84 Water Temperature Sending Unit, 84 Weather Cap, Exhaust, 94 Webbing, Fuel Tank, 76 Wheel Bearings, Disc, 180 Bearings, Front, 136, 138 Bearings, Gauge Wheel, 177 Bolt, 139 to 140 Bolt, Front, 140 Cap, Hub, 138 Clamp, Rear, 140 Front, 139 Gauge, 177 Hub, 139 Nut, 140 Nut, Clamp Lock, 138 Nut, Front, 139 Rear, 140 Rim, Rear, 140 Screw, Power Adjust Stop, 140 Sleeve, Implement Wheel Seal, 180 Steering, 127 Stop, Power Adjust, 140 Tire, Cultivator Gauge Wheel, 177 Wires, Spark Plug, 97 Wood Block, Chain Idler, 175 MF-I

Model Machine Type Engine Index Fuel Engine model (CID) Page No. A6-354.4 Engine Diesel A6-354.4 Perkins MF-1-69 AT6-354.4 Engine Diesel AT6-354.4 Turbo Perkins MF-1-69 F40 Tractor Gas Z134 Continental MF-1-5 to MF-1-7 FE35 Tractor Diesel A3-152 Perkins.040 Sleeve flange thickness MF-1-17 to MF-1-19 FE35 Tractor Diesel A3-152 Perkins.150 Sleeve flange thickness MF-1-20 to MF-1-22 MF1080 Tractor Diesel A4-318 Perkins MF-1-57 to MF-1-58 MF1085 Tractor Diesel A4-318 Perkins MF-1-57 to MF-1-58 MF1100 Tractor Diesel A6-354 Perkins To Engine s/n 354UA3515 MF-1-59 to MF-1-60 MF1100 Tractor Diesel A6-354 Perkins Engine s/n 354UA3515 thru 354UA10361 MF-1-61 to MF-1-62 MF1100 Tractor Diesel A6-354 Perkins Engine s/n 354UA10362 & up MF-1-63 to MF-1-64 MF1105 Tractor Diesel AT6-354 Turbo Perkins MF-1-67 to MF-1-68 MF1130 Tractor Diesel AT6-354 Turbo Perkins To Engine s/n 354UA3356T MF-1-65 to MF-1-66 MF1135 Tractor Diesel AT6-354 Turbo Perkins MF-1-67 to MF-1-68 MF135 Tractor Diesel AD3-152 Perkins.150 Sleeve flange thickness MF-1-23 to MF-1-26 MF135 Tractor Gas AG3-152 Perkins MF-1-14 to MF-1-16 MF135 (Deluxe) MF135 (Special) Tractor Gas Z145 Continental MF-1-8 to MF-1-10 Tractor Gas Z134 Continental MF-1-5 to MF-1-7 MF150 Tractor Diesel AD3-152 Perkins.150 Sleeve flange thickness MF-1-23 to MF-1-26 MF150 Tractor Gas Z145 Continental MF-1-8 to MF-1-10 MF150 Tractor Gas AG3-152 Perkins MF-1-14 to MF-1-16 MF165 Tractor Diesel MF165 Tractor Diesel AD4-203 Perkins.150 Sleeve flange thickness Engine s/n 2939036 to 29C1084 AD4-203 Perkins.150 Sleeve flange thickness Engine s/n 29C1084 & up MF-1-45 to MF-1-46 MF-1-47 to MF-1-48 MF165 Tractor Gas G176 Continental MF-1-11 to MF-1-12 MF175 Tractor Diesel A4-236 Perkins MF-1-49 to MF-1-50 MF180 Tractor Diesel A4-236 Perkins MF-1-49 to MF-1-50 MF230 Tractor Diesel AD3-152 Perkins.150 Sleeve flange thickness MF-1-27 to MF-1-29 MF235 Tractor Diesel MF235 Tractor Diesel MF235 Tractor Diesel MF235 Tractor Diesel AD3-152 Perkins.150 Sleeve flange thickness Engine s/n ending in DL AD3-152 Perkins.150 Sleeve flange thickness Engine s/n ending in DL AD3-152 Perkins.150 Sleeve flange thickness Engine s/n ending in DS AD3-152 Perkins.150 Sleeve flange thickness Engine s/n ending in DLS MF-1-23 to MF-1-26 MF-1-27 to MF-1-29 MF-1-30 to MF-1-32 MF-1-33 to MF-1-34 continues MF-II

Model Machine Type MF245 Tractor Diesel MF245 Tractor Diesel MF250 Tractor Diesel MF250 Tractor Diesel MF255 Tractor Diesel Engine Index Fuel Engine model (CID) Page No. AD3-152 Perkins.150 Sleeve flange thickness Engine s/n ending in DS AD3-152 Perkins.150 Sleeve flange thickness Engine s/n ending in DLS AD3-152 Perkins.150 Sleeve flange thickness Engine s/n prefix CE22488U only AD3-152 Perkins.150 Sleeve flange thickness Engine s/n prefix CE31089U only AD4-203 Perkins.150 Sleeve flange thickness Engine s/n 29C1084 & up MF-1-30 to MF-1-32 MF-1-33 to MF-1-34 MF-1-35 to MF-1-36 MF-1-37 to MF-1-38 MF-1-47 to MF-1-48 MF255 Tractor Diesel A4-236 Perkins MF-1-51 to MF-1-52 MF265 Tractor Diesel A4-236 Perkins To Engine s/n 236UA109215L MF-1-49 to MF-1-50 MF265 Tractor Diesel A4-236 Perkins Engine s/n 236UA109215L & up MF-1-51 to MF-1-52 MF275 Tractor Diesel A4-248 Perkins Engine s/n prefix 248UA or LF --- N or LF --- U only MF-1-53 to MF-1-54 MF285 Tractor Diesel A4-318 Perkins MF-1-57 to MF-1-58 MF290 Tractor Diesel A4-248 Perkins Early with 4 ring piston MF-1-55 to MF-1-56 MF294-4 Tractor Diesel A4-248 Perkins MF-1-55 to MF-1-56 MF35 Tractor Diesel A3-152 Perkins.040 Sleeve flange thickness MF-1-17 to MF-1-19 MF35 Tractor Diesel A3-152 Perkins.150 Sleeve flange thickness MF-1-20 to MF-1-22 MF35 Tractor Gas Z134 Continental MF-1-5 to MF-1-7 MF50 Tractor Diesel A3-152 Perkins.040 Sleeve flange thickness MF-1-17 to MF-1-19 MF50 Tractor Diesel A3-152 Perkins.150 Sleeve flange thickness MF-1-20 to MF-1-22 MF50 Tractor Gas Z134 Continental MF-1-5 to MF-1-7 MF65 Tractor Diesel MF65 Tractor Diesel MF65 Tractor Diesel MF65 Tractor Diesel MF65 Tractor Diesel A4-203 Perkins.040 Sleeve flange thickness To Engine s/n 2820092 A4-203 Perkins.150 Sleeve flange thickness Engine s/n 2820092 & up AD4-203 Perkins.040 Sleeve flange thickness To Engine s/n 2939036 AD4-203 Perkins.150 Sleeve flange thickness Engine s/n 2939036 to 29C1084 AD4-203 Perkins.150 Sleeve flange thickness Engine s/n 29C1084 & up MF-1-39 to MF-1-40 MF-1-41 to MF-1-42 MF-1-43 to MF-1-44 MF-1-45 to MF-1-46 MF-1-47 to MF-1-48 MF65 Tractor Gas G176 Continental MF-1-11 to MF-1-12 MF690 Tractor Diesel A4-248 Perkins To Engine s/n LF --- U839080J MF-1-55 to MF-1-56 MH44 Tractor Gas H260 MF-1-13 MH50 Tractor Gas Z134 Continental MF-1-5 to MF-1-7 Super 92 Combine Diesel A6-305 Perkins MF-1-70 TE20 Tractor Gas Z120 Continental MF-1-1 to MF-1-2 continues MF-III

Model Machine Type Engine Index Fuel Engine model (CID) Page No. TO20 Tractor Gas Z120 Continental MF-1-1 to MF-1-2 TO30 Tractor Gas Z129 Continental MF-1-3 to MF-1-4 TO35 Tractor Gas Z134 Continental MF-1-5 to MF-1-7 20 Industrial Diesel 20 Industrial Diesel AD3-152 Perkins.150 Sleeve flange thickness To engine s/n 152UA391044DL AD3-152 Perkins.150 Sleeve flange thickness Engine s/n 152UA391044DL & up MF-1-23 to MF-1-26 MF-1-27 to MF-1-29 20 Industrial Gas AG3-152 Perkins MF-1-14 to MF-1-16 20C Industrial Diesel 20C Industrial Diesel AD3-152 Perkins.150 Sleeve flange thickness Engine s/n ending in DS AD3-152 Perkins.150 Sleeve flange thickness Engine s/n ending in DLS MF-1-30 to MF-1-32 MF-1-33 to MF-1-34 200 Crawler Diesel AD3-152 Perkins.150 Sleeve flange thickness MF-1-23 to MF-1-26 200B Crawler Diesel AD3-152 Perkins.150 Sleeve flange thickness MF-1-27 to MF-1-29 202 Industrial Gas Z134 Continental MF-1-5 to MF-1-7 203 Industrial Diesel 203 Industrial Diesel 203 Industrial Diesel A3-152 Perkins.040 Sleeve flange thickness To Tractor s/n 659002115 A3-152 Perkins.150 Sleeve flange thickness To Tractor s/n 659002115 AD3-152 Perkins.150 Sleeve flange thickness Tractor s/n 659002115 & Up MF-1-17 to MF-1-19 MF-1-20 to MF-1-22 MF-1-23 to MF-1-26 204 Industrial Gas Z134 Continental MF-1-5 to MF-1-7 205 Industrial Diesel 205 Industrial Diesel 205 Industrial Diesel A3-152 Perkins.040 Sleeve flange thickness To Tractor s/n 659101250 A3-152 Perkins.150 Sleeve flange thickness To Tractor s/n 659101250 AD3-152 Perkins.150 Sleeve flange thickness Tractor s/n 659101250 & Up MF-1-17 to MF-1-19 MF-1-20 to MF-1-22 MF-1-23 to MF-1-26 2135 Industrial Diesel AD3-152 Perkins.150 Sleeve flange thickness MF-1-23 to MF-1-26 2200 Treever Diesel AD3-152 Perkins.150 Sleeve flange thickness MF-1-23 to MF-1-26 2200 Forklift Diesel AD3-152 Perkins.150 Sleeve flange thickness MF-1-23 to MF-1-26 2244 Crawler Diesel AD3-152 Perkins.150 Sleeve flange thickness MF-1-23 to MF-1-26 2500 Forklift Diesel 2500 Forklift Diesel AD3-152 Perkins.150 Sleeve flange thickness To engine s/n 152UA391044DL AD3-152 Perkins.150 Sleeve flange thickness Engine s/n 152UA391044DL & up MF-1-23 to MF-1-26 MF-1-27 to MF-1-29 2500 Forklift Gas AG3-152 Perkins MF-1-14 to MF-1-16 30 Industrial Diesel 30B Industrial Diesel AD4-203 Perkins.150 Sleeve flange thickness Engine s/n 29C1084 & up AD3-152 Perkins.150 Sleeve flange thickness Engine s/n ending in DS MF-1-47 to MF-1-48 MF-1-30 to MF-1-32 continues MF-IV

Model Machine Type 30B Industrial Diesel 300 Combine Diesel 300 Combine Diesel 302 Industrial Diesel 302 Industrial Diesel 304 Industrial Diesel 304 Industrial Diesel Engine Index Fuel Engine model (CID) Page No. AD3-152 Perkins.150 Sleeve flange thickness Engine s/n ending in DLS AD4-203 Perkins.150 Sleeve flange thickness Engine s/n 2939036 to 29C1084 AD4-203 Perkins.150 Sleeve flange thickness Engine s/n 29C1084 & up AD4-203 Perkins.150 Sleeve flange thickness Engine s/n 2939036 to 29C1084 AD4-203 Perkins.150 Sleeve flange thickness Engine s/n 29C1084 & up AD4-203 Perkins.150 Sleeve flange thickness Engine s/n 2939036 to 29C1084 AD4-203 Perkins.150 Sleeve flange thickness Engine s/n 29C1084 & up MF-1-33 to MF-1-34 MF-1-45 to MF-1-46 MF-1-47 to MF-1-48 MF-1-45 to MF-1-46 MF-1-47 to MF-1-48 MF-1-45 to MF-1-46 MF-1-47 to MF-1-48 31 Industrial Diesel A4-236 Perkins MF-1-49 to MF-1-50 3165 Industrial Diesel 3165 Industrial Diesel AD4-203 Perkins.150 Sleeve flange thickness Engine s/n 2939036 to 29C1084 AD4-203 Perkins.150 Sleeve flange thickness Engine s/n 29C1084 & up MF-1-45 to MF-1-46 MF-1-47 to MF-1-48 35 Utility Industrial Diesel A3-152 Perkins.040 Sleeve flange thickness MF-1-17 to MF-1-19 35 Utility Industrial Diesel A3-152 Perkins.150 Sleeve flange thickness MF-1-20 to MF-1-22 356 356 356 356 356 Tractor Shovel Tractor Shovel Tractor Shovel Tractor Shovel Tractor Shovel Diesel Diesel Diesel Diesel Diesel 40 Industrial Diesel 40 Industrial Diesel A4-203 Perkins.040 Sleeve flange thickness To Engine s/n 2820092 A4-203 Perkins.150 Sleeve flange thickness Engine s/n 2820092 & up AD4-203 Perkins.040 Sleeve flange thickness To Engine s/n 2939037 AD4-203 Perkins.150 Sleeve flange thickness Engine s/n 2939036 to 29C1084 AD4-203 Perkins.150 Sleeve flange thickness Engine s/n 29C1084 & up AD3-152 Perkins.150 Sleeve flange thickness To engine s/n 152UA391044DL AD3-152 Perkins.150 Sleeve flange thickness Engine s/n 152UA391044DL & up MF-1-39 to MF-1-40 MF-1-41 to MF-1-42 MF-1-43 to MF-1-44 MF-1-45 to MF-1-46 MF-1-47 to MF-1-48 MF-1-23 to MF-1-26 MF-1-27 to MF-1-29 40 Industrial Gas AG3-152 Perkins MF-1-14 to MF-1-16 40B Industrial Diesel AD4-203 Perkins.150 Sleeve flange thickness Engine s/n 29C1084 & up MF-1-47 to MF-1-48 4500 Forklift Diesel AD3-152 Perkins.150 Sleeve flange thickness MF-1-27 to MF-1-29 50 Industrial Diesel AD4-203 Perkins.150 Sleeve flange thickness Engine s/n 29C1084 & up MF-1-47 to MF-1-48 50C Industrial Diesel A4-236 Perkins MF-1-51 to MF-1-52 continues MF-V

Model Machine Type Engine Index Fuel Engine model (CID) Page No. 540 Combine Diesel A4-318 Perkins MF-1-57 to MF-1-58 6500 Forklift Diesel A4-236 Perkins To Engine s/n 236UA109215L MF-1-49 to MF-1-50 6500 Forklift Diesel A4-236 Perkins Engine s/n 236UA109215L & up MF-1-51 to MF-1-52 750 Combine Diesel AT6-354 Turbo Perkins To Machine s/n 169615716 MF-1-67 to MF-1-68 760 Combine Diesel AT6-354 Turbo Perkins To Machine s/n 1746009413 MF-1-67 to MF-1-68 MF-VI

YEAR OF MANUFACTURE AND STARTING SERIAL NUMBER MF-35 1960... 204181 1961... 211071 1962... 222207 1963... 235123 MF-50 1958... 515708 1959... 522693 1960... 528163 1961...680210 1962... 685370 1963... 693040 1964...701057 MF-85 1959... 800001 1960... 804355 1961... 807750 1962... 808564 MF-88 1959... 880001 1960... 881453 1961... 882229 1962... 882496 MF-90 1962... 810000 1963...813170 1964... 816113 1965... 819342 MF-90WR 1962... 885000 1963... 835870 1964... 886829 1965... 888238 MF-97D 1962... 25200001 1963... 25200506 1964... 25202005 MF-97LPG 1962... 25300001 1963... 25300096 1964... 25300397 MF-135 1964...641000001 1965...641001909 1966... 641014871 1967... 9A10001 1968...9A39836 1969... 9A63158 1970...9A87325 1971... 9A107519 1972... 9A128141 1973... 9A152025 1974... 9A182761 1975... 9A207681 MF-150 1964... 642000001 1965...642000015 1966... 631000505 1967... 9A10001 1968...9A39836 1969... 9A63158 1970...9A87325 1971... 9A107519 1972... 9A128141 1973... 9A152025 1974... 9A182761 1975... 9A207681 MF154-4 1980... 2226706 1981... 2227212 154S-2 1986... 13300288 1987... 133A00489 1988... 133C00645 1989... 133C00791 154S-4 1986... 23300755 1987...233A01012 1988... 233C01304 1989...233C01511 MF-165 1964... 643000001 1965... 643000003 1966...643000149 1967... 9A10001 1968...9A39836 1969... 9A63158 1970...9A87325 1971... 9A107519 1972... 9A128141 1973... 9A152025 1974... 9A182761 1975... 9A207681 174S-2 1986... 13200653 1987... 132A00912 1988... 132C01178 1989...132C01413 174S-4 1986...23201344 1987... 232A01754 1988... 1232C02271 1989...232C02679 MF-175 1964... 644000001 1965... 644000004 1966... 644000214 1967... 9A10001 1968...9A39836 1969... 9A36158 1970...9A87325 1971... 9A107519 1972... 9A128141 1973... 9A152025 1974... 9A182761 1975... 9A207681 MF-180 1964... 645000001 1965... 645000002 1966... 645000047 1967... 9A10001 1968...9A39836 1969... 9A63158 1970...9A87325 1971... 9A107519 1972... 9A128141 1973... 9A152025 1974... 9A182761 1975... 9A207681 MF-184-4 1976... 22000001 1977... 22000930 1978...22001860 1979... 22002789 1980... 22003890 1981... 2205600 194F-2 1986...14000014 1987...140D00025 1988...140D00037 1989...140D00062 194-F 1986...24000129 1987...240D00382 1988...240D00925 1989... 240D01456 194S-2 1989... 141D00136 194S-4 1989...241D00393 MF-205 1978... 00101 1979... 00315 1980... 9A10001 1981...01512 1982...01966 1983... 02159 1984... 02337 MF-205-4 1979... 00101 1980... 0677 1981... 0916 1982...01390 1983...01440 1984...01516 MF-210 1978... 00101 1979... 00961 1980... 001711 1981... 002700 1982... 03982 1983... 04231 1984... 04902 MF-210-4 1979... 00101 1980...00711 1981... 00764 1982...01595 1983...01915 1984... 02209 MF-220 1978... 00101 1979... 00300 1980... 00552 1981... 00750 1982...01339 1983...01458 1984...01708 MF-220-4 1979... 00101 1980... 00520 1981... 00868 1982...01673 1983...01981 1984... 02163 MF-230 1976...9A232539 1977...9A257837 1978... 9A280301 1979...9A300200 1980... 9A326169 1981...9A339343 1982...9A350584 1983...9A354679 MF-231 1989...P17001 1990... Q01001 1990... R08001 1991...S01001 1992...A01001 1993...B01001 1994...C01001 MF-235 1975... 9A207681 1976...9A232539 MF-VII

MF-240 1983...524172 1984...552016 1985... 557882 1986... 562369 1987...V01001 1988... N01001 1989... 901001 1990...R01001 1991...S01001 1992...A01001 1993...B01001 1994...C01001 MF-245 1976...9A242489 1977...9A257837 1978... 9A280301 1979...9A300200 1980... 9A326169 1981...9A339343 1982...9A350584 1983...9A354679 MF-250 1983... 621838 1984... 624021 1985... 627250 1986... 629926 MF-253 1988... N01001 1989...P01001 1990...R01001 1991...S01001 1992...A01001 1993...B01001 1994...C01001 MF-254-4 1982... 2229282 1983... 2229927 1984...22210485 1985... 222M01750 1986... 22202733 1987... 22203556 MF-255 1975... 9A207681 1976...9A262539 1977...9A257837 1978... 9A280301 1979...9A300200 1980... 9A326169 1981...9A339343 MF-261 1992... A22001 1993...B01001 1994...C01001 MF-265 1975... 9A207681 1976...9A232539 1977...9A257837 1978... 9A280301 1979...9A300200 1980... 9A326169 1981...9A339343 1982...9A350584 1983...9A354679 MF-270 1983... 286152 1984...287179 1985...288016 1986... 288425 MF-274-4 1982... 22111297 1983... 22112162 1984...22112828 1985...221N02384 1986...22103628 1987...22104826 MF-275 1975... 9A207681 1976...9A232539 1977...9A257837 1978... 9A280301 1979...9A300200 1980... 9A326169 1981...9A339343 1982...9A350584 1983...9A354679 MF-282(S) 1982... KC24457S 1983... KD26466S MF-282(H) 1982... KC25226H 1983... KD25518H MF-283 1985...393474 1986... 723784 1987... 00001 1988...00102 1989...01202 1990...R01001 1991... 02052 1992... 2502 1993...B01001 1994...C01001 MF-285 1974... 9A182761 1975... 9A207681 1976...9A232539 1977...9A257837 1978... 9A280301 1979...9A300200 1980... 9A326169 1981...9A339343 1982...9A350584 MF-290 1983... 386453 1984... 389947 1985... 393422 1986... 723909 MF-294-4 1982... 2235938 1983... 2236290 1984...2236511 1985...23D00915 1986...22301652 1987... 22302505 MF-298 1983... 702586 1984... 703062 1985...703760 1986... 704095 MF-360 1986... U01001 1987...V01001 1988... N01001 1989...P01001 1990...R01001 1992...A01001 MF-362 1990...R01001 1991...S01001 1992...A01001 1993...B01001 1994...C01001 MF-364 1989...P01001 1990...R01001 1991...S01001 1992...A01001 1993...B01001 MF-374 1989...P01001 1990...R01001 1991...S01001 1992...A01001 1993...B01001 MF-375, MF-383 1986... U01001 1987...V01001 1988... N01001 1989...P01001 1990...R01001 1991...S01001 1992...A01001 1993...B01001 1994...C01001 MF-384 1989...P01001 1990...R01001 1991...S01001 1992...A01001 1993...B01001 1994...C01001 MF-390 1986... U01001 1987...V01001 1988... N01001 1989...P01001 1990...R01001 1991...S01001 1992...A01001 1993...B01001 1994...C01001 MF-390T, MF394 1989...P01001 1990...R01001 1991...S01001 1992...A01001 1993...B01001 MF-393, MF-396 1992...A01001 1993...B01001 1994...C01001 MF-398, MF399 1986... U01001 1987...V01001 1988... N01001 1989...P01001 1990...R01001 1991...S01001 1992...A01001 1993...B01001 1994...C01001 MF-670 1983...B207021 1983... K183027 1984... T101001 1985... L101001 1986... U031001 MF-690 1983... B197022 1984... K181026 1985... L101001 1986... U031001 MF-698 1983... B201031 1983... K186009 1984... T101001 1985... L101001 1986... U031001 MF-699 1984... T101001 1985... L101001 1986... U031001 MF-VIII

1010 2WD 1982... 00101 1983... 00613 1984...10901 1985...11727 1986... 12075 1987... 13902 1988... 14433 1989... NA 1990... 14549 1991... 14840 1992... 14937 1010 2WD HYDRO 1987... 13953 1988... 14455 1989... 14549 1990... 14600 1991... 14879 1992... NA 1010 4WD 1982... 40101 1983... 40607 1984... 40809 1985... 41491 1986...42317 1987... 43683 1988... 44498 1989... 44696 1990... 44886 1991...45211 1992... 45362 1010 4WD HYDRO 1987... 43640 1988... 44370 1989... 44696 1990... 44907 1991... 45226 1992... NA 1020 2WD 1983... 00101 1984...00411 1985... 00809 1986...01548 1987... 02394 1988... 02707 1989...02768 1990... 02913 1991... 03159 1992... 03262 1020 WD HYDRO 1987... 02319 1988... 02707 1989...02768 1990... 02933 1991... 03157 1992... NA 1020 4WD 1983... 40101 1984... 40395 1985... 40549 1986... 41002 1987...41787 1988... 42273 1989... 42532 1990... 42963 1991... 43326 1992... 43647 1020 4WD HYDRO 1987...41709 1988... 42343 1989... 42641 1990...43016 1991... 43355 1992... NA MF-1030-2WD 1984... 00101 1985... 00820 1986... 01501 MF-1030 2WD 1984... 00101 1985... 00820 1986... 01501 MF-1030L-2 1988... 02067 1987... 02542 1988... 03139 1989... 03285 1990... 03308 1991... 03713 MF-1030 4WD 1984... 40101 1985... 40600 1988... 41245 MF-1030L-4 1986...41713 1987... 42167 1988... 42594 1989... 42953 1990... 43251 1991... 43549 MF-1035 2WD 1986...00100 1987... 00315 1988... NA 1989... 00540 1990... 00585 1991... 00729 MF-1035 4WD 1986...40100 1987... 40377 1988... 40691 1989... 40936 1990...41058 1991... 41252 MF-1040 2WD 1984... 00101 1985...00155 1986... 00552 MF-1040 4WD 1984... 40101 1985... 40351 1986... 40562 MF-1045 2WD 1986...00100 1987... 00234 1988... NA 1989... 00334 1990... 00334 MF-1045 4WD 1986...40100 1987... 40275 1988... 40566 1989... 40757 1990...41144 MF-1080 1969... 9B18673 1970...9B23486 1971...9B28227 1972... 9B31958 MF-1085 1973...9B36841 1974...9B43432 1975...9B50494 1976...9B58735 1977...9B67772 1978... 9B76058 MF-1100 1964... 650000001 1965...650000003 1966... 650000831 1967... 9B10001 1968... 9B14693 1969... 9B18673 1970...9B23486 1971...9B28227 1972... 9B31958 MF1105 1973...9B36841 1974...9B43432 1975...9B50494 1976...9B58735 1977...9B67772 1978... 9B75182 1978... 9B76058 MF-1125 1992...A40101 MF-1130 1964... 650500001 1965... 650500004 1966... 65150049 1967... 9B10001 1968... 9B14693 1969... 9B18673 1970...9B23486 1971...9B28227 1972... 9B31958 MF-1135, MF-1155 1973...9B36841 1974...9B43432 1975...9B50494 1976...9B58735 1977...9B67772 1978... 9B75182 1978... 9B76058 MF-1140-2 1991...S201001 1992...A50101 MF-1140-4 1991...S201001 1992...A50101 MF-1145-4 1991...S201001 1992...A50101 MF-1160 4WD 1992...A70101 1993...B70101 MF-1180 1992...A80101 1993...B80101 MF-1190 1992...A90101 1993...A90101 MF-1210 1993...B10101 MF-1220 1993...B20101 MF-1230 1993...B30101 MF-1240 1992... A44401 1993...B40101 MF-1250 1992... A54401 1993...B50101 MF-1260 1992... A64401 1993...B60101 MF-1500, MF-1800 1971... 9C001007 1972... 9C001912 1973...9C002463 1974...9C003184 MF-1505, MF-1805 1974...9C003184 1975...9C004227 1976...9C006806 1977...9C007858 MF-I

2640 2WD 1982...S276213 1983... B160217 1983... K181026 2640 4WD 1982...S276213 1983... B160217 1983... K181026 MF-2675, MF-2705 1978...9R000733 1979...9R003482 1980...9R007282 1981... 9R010307 1982... 9R013230 1983...9R03525 MF-2745 1978...9R000733 1979...9R003482 1980...9R007282 1981... 9R010307 1982... 9R013230 1983... 9R013525 MF-2775 1977...9R000092 1978...9R000733 1979...9R003482 1980...9R007282 1981... 9R010307 1982... 9R013230 1983... 9R013525 MF-2805 1976...9R000001 1977...9R000092 1978...9R000733 1979...9R003482 1980...9R007282 1981... 9R010307 1982... 9R013230 1983... 9R013525 MF-3050 1986... U031001 1987...V001001 1988... N001001 1989...P001001 MF-3060 1986... U031001 1987...V001001 1988... N001001 1989...P001001 1990...R001001 MF-3070 1986... U031001 1987...V001001 1988... N001001 1989...P001001 1990...R001001 1991...S001001 1992...A001001 1993...B001001 MF-3075 1993...B001001 1994...C001001 MF-3090 1986... U031001 1987...V001001 1988... N001001 1989...P001001 1990...R001001 MF-3120, MF-3140 1990...R001001 1991...S001001 1992...A001001 1993...B001001 1994...C001001 MF-3505 1984... K241203 1985... L101201 1986... U031201 1987...V001201 MF-3525 1984... K241203 1985... L101201 1986... U031201 1987...V001201 MF-3545 1984... K242206 1985... L101201 1986... U031201 1987...V001201 MF-3630, MF-3650 1987...V001001 1988... N001001 1989...P001001 1990...R001001 MF-3660 1990...R001001 1991...S001001 1992...A001001 1993...B001001 1994...C001001 MF-3670 1992...A001001 1993...B001001 1994...C001001 MF-3680 1988...N293001 1989...P001001 1990...R001001 1991...S001001 MF-3690 1991... S180001 1992...A001001 1993...B001001 1994...C001001 MF-4800 1979... 9D001031 1980...9D002102 1981...9D002752 1982...9D003515 1983...9D003897 MF-4840, MF-4880 1978... 9D001001 1979... 9D001031 1980...9D002102 1981...9D002752 1982...9D003515 1983...9D003897 MF-4900 1980...9D002102 1981...9D002752 1982...9D003515 1983...9D003897 MF-

MF-I

1 ENGINES Replacement parts to fit Tractor: TE20, TO20 Z120 120 CID 4 Cylinder Continental Gas 3-5/16" Overbore Supplied, Standard Bore 3-3/16" TRU-POWER Engine Kits (Pin type valves furnished in EOK.) Engine bearings must be ordered separately. Cylinder Parts 20K600-LCB BEKM118-LCB Complete overhaul kit. Contains sleeve & piston kit, complete gasket set, pin bushings, valve overhaul kit, fan belt, oil pump repair kit, oil filter element, air cleaner hose, upper & lower radiator hose, distributor points & condenser, spark plugs, Marvel-Schebler basic carburetor kit. Basic engine kit. Contains sleeves, sleeve seals, pistons & rings, pins & retainers, pin bushings, gasket sets, & crankshaft seals. PRS106 836092M91 840708M91 Ring set for 4 pistons. For 3-5/16" overbore Super Power pistons. 2 @ 3/32", 2 @ 5/32" Ring set for 4 pistons. For 3-3/16" standard bore replacing original rings. 3 @ 1/8", 1 @ 3/16" Bushing kit, 4-760916M1 pin bushings. EOK118-LCB Engine overhaul kit. Contains sleeves, pistons, rings, pins, overhaul gasket set, valves, springs, guides, and keys. 760916M1 Bushing, piston pin BIFM118 Basic in-frame kit. Contains sleeve & piston kit with rings, pins & retainers, valve grind set, oil pan gasket. Gaskets Sleeve & Piston Kit 830631M91 Complete gasket set, less crankshaft seals. TO20VG Valve grinding set. 1750336M1 Gasket, cylinder head. 1750274M1 Gasket, timing gear cover. 1750269M1 Gasket, hand hole cover to pan. Complete for one engine. (Super Power Kit increases bore to 3-5/16".) 1750002M1 1750006M1 Gasket, cylinder head cover. Gasket, vent cover, cylinder head. PK106 Sleeve & piston kit. Contains sleeves, sleeve seals, pistons & rings, pins & retainers. Increases bore to 3-5/16". 1750062M1 1750045M1 Seal, oil, intake valve stem Gasket, manifold. Tractors: TO20, TO30, TO35, MF35, F40, MF50, MF135. 1750024M1 Gasket, oil pan to block. 1750000M1 Gasket, rubber, cylinder sleeve. 1006635M1 Packing, rear main bearing cap. MF-1-1

1 ENGINES Tractor: TE20, TO20 Z120 120 CID 4 Cylinder Continental Gas 3-5/16" Overbore Supplied, Standard Bore 3-3/16" Crankshaft Seals Connecting Rod Bearing Kits 1 kit used per engine. 15287A Seal, front, lip-type. 15288A Front dust seal, felt. For Continental engines. 830486M91 Rod bearing kit, standard 1750216M92 Seal, rear, lip-type. For Continental engines. 830508M91 Rod bearing kit,.002" 1750112M1 Rear seal gasket. Use with 1750216M92. 830509M91 Rod bearing kit,.010" CSK3 Seal kit. Contains front seal & dust felt, rear seal & gasket for crankshaft. For Continental engines. Valve Parts 830510M91 830510-030 Rod bearing kit,.020" Rod bearing kit,.030" Main Bearing Kits Includes thrust washers (1 kit used per engine) Pin Type Valves MBKZ120 Main bearing kit, standard VOKM120 Valve overhaul kit. Contains intake & exhaust valves, springs, keys, guides. MBKZ120-010 MBKZ120-020 Main bearing kit,.010" Main bearing kit,.020" 1751518M1 Valve, engine intake, pin type 1751519M1 Valve, engine exhaust, pin type 830726M91 Valve, engine exhaust, pin type (set of 4) 830490M91 Guide, intake & exhaust valve (set of 8) 21176A Spring, intake & exhaust valve 840754M91 Spring, intake & exhaust valve (set of 8) 18291A Lock, intake & exhaust valve, pin type (1 used per valve) 1750062M1 Seal, oil, intake valve stem MF-1-2

1 ENGINES Replacement parts to fit Tractor: TO30 Z129 129 CID 4 Cylinder Continental Gas 3-3/8" Overbore Supplied, Standard Bore 3-1/4" TRU-POWER Engine Kits (Pin-type intake & key-type exhaust valves furnished in EOK) "Super Power" sleeve & piston kit, increases bore to 3-3/8". Engine bearings must be ordered separately. Cylinder Parts 30K600-LCB Complete overhaul kit. Contains sleeve & piston kit, complete gasket set, pin bushings, valve overhaul kit, fan belt, oil pump repair kit, oil filter element, air cleaner hose, upper & lower radiator hose, distributor points & condenser, spark plugs, Marvel-Schebler basic carburetor kit. PRS105 836096M91 760916M1 Ring set for 4 pistons. For 3-3/8" overbore Super Power pistons. 3 @ 3/32", 1 @ 3/16" Ring set for 4 pistons. For 3-1/4" standard bore replacing original rings. 3 @ 1/8", 1 @ 3/16" Bushing, piston pin EOK119FL-LCB Engine overhaul kit. Contains sleeves, pistons & rings, pins & retainers, pin bushings, complete gasket set, crankshaft seals, valves, springs, guides, & keys. 840708M91 Bushing kit, 4-760916M1 pin bushings. BEKM119FL-LCB Basic engine kit. Contains sleeves, sleeve seals, pistons & rings, pins & retainers, pin bushings, gasket sets, crankshaft seals. Gaskets BIFM119FL Basic in-frame kit. Contains sleeve & piston kit with rings, pins & retainers, valve grind gasket set, oil pan gasket. Sleeve & Piston Kit 830631M91 Complete gasket set, less crankshaft seals. TO20VG Valve grinding set. 1750336M1 Gasket, cylinder head. 1750274M1 Gasket, timing gear cover. 1750002M1 Gasket, cylinder head cover. 1750006M1 Gasket, vent cover, cylinder head. PK105 Complete for one engine. (Super Power Kit, increases bore to 3-3/8") Sleeve & piston Kit. Contains sleeves, sleeve seals, pistons & rings, pins & retainers. Increases bore to 3-3/8". 1750062M1 1750045M1 1750024M1 1750000M1 Seal, oil, intake valve stem Gasket, manifold. Tractors: TO20, TO30, TO35, MF35, F40, MF50, MF135. Gasket, oil pan to block. Gasket, rubber, cylinder sleeve. 1006635M1 Packing, rear main bearing cap. MF-1-3

1 ENGINES Tractor: TO30 Z129 129 CID 4 Cylinder Continental Gas 3-3/8" Overbore Supplied, Standard Bore 3-1/4" Crankshaft Seals Connecting Rod Bearing Kits 1 kit used per engine. 15287A Seal, front, lip-type. 15288A Front dust seal, felt. For Continental engines. 830486M91 Rod bearing kit, standard 1750216M92 Seal, rear, lip-type. For Continental engines. 830508M91 Rod bearing kit,.002" 1750112M1 Rear seal gasket. Use with 1750216M92. 830509M91 Rod bearing kit,.010" CSK3 Seal kit. Contains front seal & dust felt, rear seal & gasket for crankshaft. For Continental engines. Valve Parts (Pin-type intake, key-type exhaust) 830510M91 830510-030 Rod bearing kit,.020" Rod bearing kit,.030" Main Bearing Kits Includes thrust washers (1 kit used per engine) VOKM129 Valve overhaul kit. Contains intake & exhaust valves, springs, keys, guides. 1750070M1 830487M91 1750072M1 830488M91 830490M91 Valve, engine intake, pin type Valve, engine intake, pin type (set of 4) Valve, engine exhaust, key type Valve, engine exhaust, key type (set of 4) Guide, intake & exhaust valve (set of 8) MBKZ120 MBKZ120-010 MBKZ120-020 Main bearing kit, standard Main bearing kit,.010" Main bearing kit,.020" Crankshaft Kits 21176A Spring, intake & exhaust valve 840754M91 18291A Spring, intake & exhaust valve (set of 8) Lock, intake & exhaust valve, pin type (1 used per valve) Z129CK Crankshaft kit with standard size rod & main bearings. For Z129 Continental gas engine in tractors: TO30 with thrust on front main. 1004512M1 Lock, intake & exhaust valve, key type (2 used per valve). Replaces 74356080 841370M91 Lock, intake & exhaust valve, key type (set of 8) 1750062M1 Seal, oil, intake valve stem MF-1-4

1 ENGINES Replacement parts to fit Industrial Tractor: 202, 204 Tractor: F40, MF135, MF35, MF50, TO35 Z134 134 CID 4 Cylinder Continental Gas 3-3/8"" Overbore Supplied, Standard Bore 3-5/16"" TRU-POWER Engine Kits (Pin-type intake & key-type exhaust valves furnished in EOK) "Super Power" sleeve & piston kit, increases bore to 3-3/8". Engine bearings must be ordered separately. Sleeve & Piston Kit 35K600-LCB 45K600-LCB Complete overhaul kit for TO35, MF35, MF135, 202 & 204 industrials. Contains sleeve & piston kit, complete gasket set, pin bushings, valve overhaul kit, fan belt, oil pump repair kit, oil filter element, air cleaner hose, upper & lower radiator hose, distributor points & condenser, spark plugs, Marvel-Schebler basic carburetor kit. Complete overhaul kit for F40 & MF50. Contains sleeve & piston kit, complete gasket set, pin bushings, valve overhaul kit, fan belt, oil pump repair kit, oil filter element, air cleaner hose, upper & lower radiator hose, distributor points & condenser, spark plugs, Marvel-Schebler basic carburetor kit. PK105 Complete for one engine. (Super Power Kit, increases bore to 3-3/8") Sleeve & piston Kit. Contains sleeves, sleeve seals, pistons & rings, pins & retainers. Increases bore to 3-3/8". Cylinder Parts EOK119-LCB BEKM119-LCB BIFM119 Engine overhaul kit. Contains sleeves, sleeve seals, pistons & rings, pins & retainers, pin bushings, complete gasket set, crankshaft seals, valves, springs, guides, & keys. Basic engine kit. Contains sleeves, sleeve seals, pistons & rings, pins & retainers, pin bushings, gasket sets, crankshaft seals. Basic in-frame kit. Contains sleeve & piston kit with rings, pins & retainers, valve grind gasket set, oil pan gasket. PRS105 836097M91 760916M1 840708M91 Ring set for 4 pistons. For 3-3/8" overbore Super Power pistons. 3 @ 3/32", 1 @ 3/16" Ring set for 4 pistons. For 3-5/16" standard bore replacing original rings. 3 @ 1/8", 1 @ 3/16". Bushing, piston pin Bushing kit, 4-760916M1 pin bushings. MF-1-5

1 ENGINES Industrial Tractor: 202, 204 Tractor: F40, MF135, MF35, MF50, TO35 Z134 134 CID 4 Cylinder Continental Gas 3-3/8"" Overbore Supplied, Standard Bore 3-5/16"" Gaskets Valve Parts 830689M91 Complete gasket set, with front seals. 836287M91 Valve grinding set. 1750017M1 Gasket, cylinder head. 1750032M1 1750002M1 1750006M1 1750062M1 1750045M1 1750024M1 1022451M1 1750000M1 1006635M1 Gasket, timing gear cover. For tractors: TO35, MF50, MF35. Gasket, cylinder head cover. Gasket, vent cover, cylinder head. Seal, oil, intake valve stem Gasket, manifold. Tractors: TO20, TO30, TO35, MF35, F40, MF50, MF135. Gasket, oil pan to block. Gasket, oil pan. For tractors: MF35. Gasket, rubber, cylinder sleeve. Packing, rear main bearing cap. Crankshaft Seals VOKM129 1750070M1 830487M91 1750072M1 830488M91 830490M91 21176A 840754M91 18291A (Pin-type intake, key-type exhaust) Valve overhaul kit. Contains intake & exhaust valves, springs, keys, guides. Valve, engine intake, pin type Valve, engine intake, pin type (set of 4) Valve, engine exhaust, key type Valve, engine exhaust, key type (set of 4) Guide, intake & exhaust valve (set of 8) Spring, intake & exhaust valve Spring, intake & exhaust valve (set of 8) Lock, intake & exhaust valve, pin type (1 used per valve) 1004512M1 Lock, intake & exhaust valve, key type (2 used per valve). Replaces 74356080 841370M91 Lock, intake & exhaust valve, key type (set of 8) 1750062M1 Seal, oil, intake valve stem 15287A Seal, front, lip-type. 15288A Front dust seal, felt. For Continental engines. 1750216M92 Seal, rear, lip-type. For Continental engines. 1750112M1 Rear seal gasket. Use with 1750216M92. CSK3 Seal kit. Contains front seal & dust felt, rear seal & gasket for crankshaft. For Continental engines. MF-1-6

1 ENGINES Replacement parts to fit Industrial Tractor: 202, 204 Tractor: F40, MF135, MF35, MF50, TO35 Z134 134 CID 4 Cylinder Continental Gas 3-3/8"" Overbore Supplied, Standard Bore 3-5/16"" Connecting Rod Bearing Kits 1 kit used per engine. Crankshaft Kits 830486M91 830508M91 Rod bearing kit, standard Rod bearing kit,.002" Z134CK Crankshaft kit with standard size rod & main bearings. For Z134 Continental gas engine in tractors: TO30 late with thrust on center main, TO35, MF35, MF135; industrial: 202. Camshafts 830509M91 Rod bearing kit,.010" 830510M91 Rod bearing kit,.020" 830510-030 Rod bearing kit,.030" Main Bearing Kits (Flanged center main bearing) 1 kit used per engine. 836543M91 Camshaft, for Continental gas engines Z120, Z129, Z134. Replaces 1750074M1, 1750293M1. Oil Pump Repair Kits 837155M91 837156M91 830639M91 830639-030 Main bearing kit, standard Main bearing kit,.010" Main bearing kit,.020" Main bearing kit,.030" OPK60A 1750087M1 Complete repair kit; replaces 835643M91, Drive gear is 2-15/16" O.D. Gasket, oil pump body cover. For tractors: TO35, F40, MF35, & MF50. MF-1-7

1 ENGINES Tractor: MF135 (Deluxe), MF150 Z145 145 CID 4 Cylinder Continental Gas Standard Bore 3-3/8" TRU-POWER Engine Kits Standard Bore 3-3/8". (Pin type intake & key type exhaust valves furnished in EOK) Bearings must be ordered separately. Cylinder Parts 37K600-LCB Complete overhaul kit. Contains sleeve & piston kit, complete gasket set, pin bushings, valve overhaul kit, fan belt, oil pump repair kit, oil filter element, air cleaner hose, upper & lower radiator hose, distributor points & condenser, spark plugs, Marvel-Schebler basic carburetor kit. 836100M91 760916M1 840708M91 Ring set for 4 pistons. For 3-3/8" standard bore. 12 @ 1/8", 4 @ 3/16" Bushing, piston pin Bushing kit, 4-760916M1 pin bushings. BEKM1135-LCB EOK1135-LCB Basic engine kit. Contains sleeves, sleeve seals, piston & rings, pins & retainers, pin bushings, gasket sets, crankshaft seals. Engine overhaul kit. Contains sleeves, pistons & rings, pins & retainers, pin bushings, complete gasket set, crankshaft seals, valves, springs, guides, & keys. Gaskets BIFM1135 Basic in-frame kit. Contains sleeve & piston kit with rings, pins & retainers, valve grinding set, oil pan gasket. Sleeve & Piston Kit 830689M91 836287M91 Complete gasket set, with front seals. Valve grinding set. 1750017M1 Gasket, cylinder head. 1750002M1 Gasket, cylinder head cover. 1750006M1 Gasket, vent cover, cylinder head. 1750062M1 Seal, oil, intake valve stem 1750045M1 Gasket, manifold. Tractors: TO20, TO30, TO35, MF35, F40, MF50, MF135. PK135 Sleeve & piston kit. Contains sleeves, sleeve seals, pistons & rings, pins & retainers. For standard 3-3/8" bore. 1750032M1 1750024M1 1750000M1 Gasket, timing gear cover. For tractors: TO35, MF50, MF35. Gasket, oil pan to block. Gasket, rubber, cylinder sleeve. 1006635M1 Packing, rear main bearing cap. MF-1-8

1 ENGINES Replacement parts to fit Tractor: MF135 (Deluxe), MF150 Z145 145 CID 4 Cylinder Continental Gas Standard Bore 3-3/8" Crankshaft Seals Connecting Rod Bearing Kits 1 kit used per engine. 15287A Seal, front, lip-type. 15288A Front dust seal, felt. For Continental engines. 830486M91 Rod bearing kit, standard 1750216M92 Seal, rear, lip-type. For Continental engines. 830508M91 Rod bearing kit,.002" 1750112M1 Rear seal gasket. Use with 1750216M92. 830509M91 Rod bearing kit,.010" CSK3 Seal kit. Contains front seal & dust felt, rear seal & gasket for crankshaft. For Continental engines. Valve Parts 830510M91 830510-030 Rod bearing kit,.020" Rod bearing kit,.030" Main Bearing Kits (Flanged center main bearing) 1 kit used per engine. VOKM145 1027654M1 1027653M1 830490M91 21176A 840754M91 (Pin-type intake, key-type exhaust) Valve overhaul kit. Contains intake & exhaust valves, springs, keys, & guides. Valve, engine intake, pin type (4 used per engine) Valve, engine exhaust, key type (4 used per engine) Guide, intake & exhaust valve (set of 8) Spring, intake & exhaust valve Spring, intake & exhaust valve (set of 8) 837155M91 837156M91 830639M91 830639-030 1750054M1 Main bearing kit, standard Main bearing kit,.010" Main bearing kit,.020" Main bearing kit,.030" Timing Gears Crankshaft gear, 24 teeth. For Continental gas engine in tractors: TO35, MF35, MF50, MH50, MF135, MF150. 18291A 1004512M1 841370M91 1750062M1 Lock, intake & exhaust valve, pin type (1 used per valve) Lock, intake & exhaust valve, key type (2 used per valve). Replaces 74356080 Lock, intake & exhaust valve, key type (set of 8) Seal, oil, intake valve stem 1750237M1 Camshaft gear, 48 teeth. For Continental gas engine in tractors: TE20, TO20, TO30, TO35, F40, MH50, MF50, MF135, MF150; industrials: 202, 204, 2135. MF-1-9

1 ENGINES Tractor: MF135 (Deluxe), MF150 Z145 145 CID 4 Cylinder Continental Gas Standard Bore 3-3/8" Camshafts 1027656M1 Camshaft with nut, 10 tooth, 1.234" gear. For Continental Z145 gas engine in tractors: MF135, MF150, MF230, MF235, MF245; industrials: 20C, 30B; forklifts: 2500, 4500. MF-1-10

1 ENGINES Replacement parts to fit Tractor: MF165, MF65 G176 176 CID 4 Cylinder Continental Gas Standard Bore 3-37/64" Stepped Head Piston TRU-POWER Engine Kits Standard Bore 3-37/64". Bearings must be ordered separately. Cylinder Parts 65K600-LCB BEKM165-LCB EOK165-LCB Complete overhaul kit. Contains sleeve & piston kit, complete gasket set, pin bushings, valve overhaul kit, fan belt, oil pump repair kit, oil filter element, air cleaner hose, upper & lower radiator hose, distributor points & condenser, spark plugs, Marvel-Schebler basic carburetor kit. Basic engine kit. Contains sleeves, sleeve seals, pistons & rings, pins & retainers, pin bushings, gasket set, crankshaft seals. Engine overhaul kit. Contains sleeves, pistons & rings, pins & retainers, pin bushings, complete gasket set, crankshaft seals, valves, springs, guides, & keys. 836103M91 1753787M1 830759M91 Ring set, for 4 pistons. For 3-37/64" standard bore. 12 @ 1/8", 4 @ 1/4" Piston pin bushing. Bushing kit, 4-1753787M1 pin bushings. Gaskets BIFM165 Basic in-frame kit. Contains sleeve & piston kit with rings, pins & retainers, valve grinding gasket set, oil pan gasket. Sleeve & Piston Kit 830766M92 836283M91 Complete gasket set, with front & rear crankshaft seals. Valve grinding set. 1753818M1 Gasket, cylinder head. 1750062M1 Seal, oil, intake valve stem 1750000M1 Gasket, rubber, cylinder sleeve. 1753804M1 Gasket, oil pan. 1006635M1 Packing, rear main bearing cap. Complete for one engine (Standard bore 3-37/64") Stepped head piston 1750216M92 Crankshaft Seals Seal, rear, lip-type. For Continental engines. PK65 Sleeve & piston kit. Contains sleeves, sleeve seals, pistons & rings, pins & retainers. For standard 3-37/64" bore. MF-1-11

1 ENGINES Tractor: MF165, MF65 G176 176 CID 4 Cylinder Continental Gas Standard Bore 3-37/64" Stepped Head Piston Valve Parts Main Bearing Kits 1 kit used per engine. 830752M91 Main bearing kit, standard 830754M91 Main bearing kit,.010" 830755M91 Main bearing kit,.020" VOKM176 Valve overhaul kit. Contains intake & exhaust valves, springs, keys, & guides. Oil Pump Repair Kits 1019742M1 Valve, engine intake 830761M91 Valve, engine intake (set of 4) 1019743M1 Valve, engine exhaust 830760M91 Valve, engine exhaust (set of 4) 1019739M1 830762M91 1010268M1 Guide, intake & exhaust valve Guide, intake & exhaust valve (set of 8) Spring, intake & exhaust valve OPK65A Oil pump repair kit. For Continental engine in tractors: MF65, MF165, MF175, MF180. Drive gear is 3-1/8" O.D. 841374M91 Spring, intake & exhaust valve (set of 8) 841375M91 Key, intake & exhaust valve (set of 16) Connecting Rod Bearing Kits 1 kit used per engine. 830748M91 Rod bearing kit, standard 830750M91 Rod bearing kit,.010" 830751M91 Rod bearing kit,.020" MF-1-12

1 ENGINES Replacement parts to fit Tractor: MH44 (1946-1954) H260 260 CID 4 Cylinder Continental Gas 4" Overbore Supplied, Standard Bore 3-7/8" Flat Head Piston TRU-POWER Engine Kits Super Power sleeve & piston kit, increases bore to 4". Engine bearings must be order separately. Gaskets BEKM1325-LCB Basic engine kit. Contains sleeves, pistons, rings, pins, and overhaul gasket set with crankshaft seal. Sleeve and Piston Kit 760234M2 Oil pan gasket set.tractors: MH44 (1946-1954) H260 4 cylinder Continental Gas. Complete for one engine. VGK7624B Valve grinding set. Flat head piston Valve Parts PK325 Sleeve & piston kit. Contains sleeves, sleeve seals, pistons & rings, pins & retainers. 4" bore. Cylinder Parts 835987M91 Guide, intake & exhaust valves (set of 8) 760196M1 Piston pin bushing. 840759M91 Key, intake & exhaust valve (set of 16) Connecting Rod Bearing Kits 1 kit used per engine. 840710M91 Bushing kit, 4-760196M1 pin bushings. 840598M92 Rod bearing kit, standard MF-1-13

1 ENGINES Forklift: 2500 Industrial Tractor: 20, 40 Tractor: MF135, MF150 AG3-152 152 CID 3 Cylinder Perkins Gas Standard Bore 3.6" TRU-POWER Engine Kits Gaskets BEKP152G-LCB Basic engine kit. Contains sleeves, pistons, rings, pins, pin bushings, and overhaul gasket set with crankshaft seals. EOK152G-LCB Engine overhaul kit. Contains sleeves, pistons, rings, pins, pin bushings, overhaul gasket set with crankshaft seals, valves, springs, guides, and keys. BIFP152G Basic in-frame kit. Contains sleeves, pistons, rings, pins, valve grind set, and oil pan gasket kit. Sleeve & Piston Kit 748007M91 738797M91 Top engine set. Bottom engine set. MF3152PG Oil pan gasket. Crankshaft Seals 1851747M1 Seal, front, lip-type. PK152G Sleeve & piston kit. Contains sleeves, pistons & rings, pins & retainers. Complete for 3-cylinders. 735866M1 Seal, rear, rope-type. For original production blocks (2 required) 739043M1 Cylinder Parts Sleeve, CAST, replacing original CAST sleeve. Flange thickness.150". Replaces 734175M1. 1447049M91 Seal, rear, lip-type (s/n 248UA123424L & up). For replacement blocks (2 required) 745815M91 740407M1 Ring set, for 1 piston. 2 @ 3/32", 1 @ 1/4". Bushing, piston pin (3 used per engine) *Both rear seal types included in engine kits MF-1-14

1 ENGINES Replacement parts to fit Forklift: 2500 Industrial Tractor: 20, 40 Tractor: MF135, MF150 AG3-152 152 CID 3 Cylinder Perkins Gas Standard Bore 3.6" Valve Parts Main Bearing Kits 1 kit used per engine (Thrust washers not included) 746156M91 Main bearing kit, standard VOKP152G 739641M1 739439M1 3637527M1 731153M1 731154M1 Valve overhaul kit. Contains intake & exhaust valves, springs, keys, guides. Valve, engine intake Valve, engine exhaust Guide, intake & exhaust valve Spring, inner, intake & exhaust valve Spring, outer, intake & exhaust valve 746157M91 746158M91 746159M91 735112M1 Main bearing kit,.010" Main bearing kit,.020" Main bearing kit,.030" Thrust Washers Thrust washer, upper. 2 used per engine. 731155M1 Key, intake & exhaust valve (12 used per engine) Connecting Rod Bearing Kits 1 kit used per engine. 735113M1 Thrust washer, lower, tabbed. 2 used per engine. 737070M91 Rod bearing kit, standard 737071M91 Rod bearing kit,.010" 737072M91 Rod bearing kit,.020" 737073M91 Rod bearing kit,.030" MF-1-15

1 ENGINES Forklift: 2500 Industrial Tractor: 20, 40 Tractor: MF135, MF150 AG3-152 152 CID 3 Cylinder Perkins Gas Standard Bore 3.6" Crankshaft Kits 3638309M91 3641825M91 3638632M91 Crankshaft kit, new, with standard rod bearings, main bearings, & thrust washers. For Perkins AG3-152 gas, A3-152 & AD3-152 diesels. Uses 2 piece rope-type rear seal. 1/2" wide flywheel flange. Crankshaft kit, new, with standard size rod & main bearings, & thrust washers. For Perkins AG3-152 gas & AD3-152 diesel engines using 1 piece lip-type rear seal, keyed nose, 1-1/2" wide flywheel flange. Replaces U5BG0027, 742827M91, 3637399M91, 3637410M91. Oil Pump Repair Kits Oil pump assembly for Perkins A3-152 & AD3-152 gas & diesel engines. Replaces 41314178 & 736513M91. MF-1-16

1 ENGINES Replacement parts to fit Industrial Tractor: 203 (prior to tractor s/n 659002115), 205 (prior to tractor s/n 659002115), 35 Utility Tractor: FE35, MF35, MF50 A3-152 152 CID 3 Cylinder Perkins Diesel Standard Bore 3.6".040 Sleeve Flange Thickness Injectors Vertical in Head BEKP1335D-LCB TRU-POWER Engine Kits Used prior to engine s/n 1935854, replacing original chrome sleeves (.040" sleeve flange thickness) Engine bearings & thrust washers must be ordered separately. Basic engine kit. Contains sleeves (.040" flange thickness), pistons, rings, pins, pin bushings, and overhaul gasket set with crankshaft seals. 732638M-CST 734460M91 Cylinder Parts Sleeve, CAST, for replacing original CHROME sleeve. Flange thickness.040". Piston with pin, flat head. EOK1335D-LCB BIFP1335D Engine overhaul kit. Contains sleeves (.040" sleeve flange thickness), pistons, rings, pins, pin bushings, overhaul gasket set with crankshaft seals, valves, springs, guides, retainers, and keys. Basic in-frame kit. Contains sleeves (.040" flange thickness), pistons, rings, pins, valve grind set, and oil pan gasket kit. Sleeve & Piston Kit PRS334DC 836325M91 Ring set for 3 pistons only, use with CHROME sleeves, can replace 3-842521M92. 2 @ 3/32", 1 @ 1/8", 2 @ 1/4". Ring set, for 1 piston, used with CAST sleeves only. 2 @ 3/32", 1 @ 1/8", and 2 @ 1/4" 740407M1 Bushing, piston pin (3 used per engine) PK334DC Complete for 1 engine Kit, with original style 732638M1 CHROME sleeves, flange thickness.040". 1851747M1 Crankshaft Seals Seal, front, lip-type. PK335D Kit, with CAST sleeves, for REPLACING original style CHROME sleeves. Flange thickness.040". 735866M1 Seal, rear, rope-type. For original production blocks (2 required) MF-1-17

1 ENGINES Industrial Tractor: 203 (prior to tractor s/n 659002115), 205 (prior to tractor s/n 659002115), 35 Utility Tractor: FE35, MF35, MF50 A3-152 152 CID 3 Cylinder Perkins Diesel Standard Bore 3.6".040 Sleeve Flange Thickness Injectors Vertical in Head Gaskets Valve Parts 747166M91 747187M91 MF3152PG Lower engine gaskets are for engines using 2 piece rope-type rear seal. Seals are included in engine kits but are not included in gasket sets. Top engine set. Bottom set, to engine s/n 19B8552. Oil pan gasket. Connecting Rod Bearing Kits VOKP152 731151M1 731152M1 732445M1 731153M1 731154M1 Valve overhaul kit. Contains intake & exhaust valves, springs, keys, & guides. Valve, intake Valve, exhaust Guide, intake & exhaust valve Spring, inner, intake & exhaust valve Spring, outer, intake & exhaust valve 731959M1 Retainer, valve spring 731155M1 Key, intake & exhaust valve (12 used per engine) Main Bearing Kits 1 kit used per engine. 737070M91 Rod bearing kit, standard 737071M91 737072M91 737073M91 Rod bearing kit,.010" Rod bearing kit,.020" Rod bearing kit,.030" 746156M91 746157M91 1 kit used per engine (Thrust washers not included) Main bearing kit, standard Main bearing kit,.010" 746158M91 Main bearing kit,.020" 746159M91 Main bearing kit,.030" MF-1-18

1 ENGINES Replacement parts to fit Industrial Tractor: 203 (prior to tractor s/n 659002115), 205 (prior to tractor s/n 659002115), 35 Utility Tractor: FE35, MF35, MF50 A3-152 152 CID 3 Cylinder Perkins Diesel Standard Bore 3.6".040 Sleeve Flange Thickness Injectors Vertical in Head Thrust Washers Crankshaft Kits 735112M1 Thrust washer, upper. 2 used per engine. 735113M1 Thrust washer, lower, tabbed. 2 used per engine. 3638309M91 Crankshaft kit, new, with standard rod bearings, main bearings, & thrust washers. For Perkins AG3-152 gas, A3-152 & AD3-152 diesels. Uses 2 piece rope-type rear seal. 1/2" wide flywheel flange. Cylinder Heads 3641825M91 Crankshaft kit, new, with standard size rod & main bearings, & thrust washers. For Perkins AG3-152 gas & AD3-152 diesel engines using 1 piece lip-type rear seal, keyed nose, 1-1/2" wide flywheel flange. Replaces U5BG0027, 742827M91, 3637399M91, 3637410M91. Oil Pump Repair Kits 3638632M91 Oil pump assembly for Perkins A3-152 & AD3-152 gas & diesel engines. Replaces 41314178 & 736513M91. 3638321M91 Cylinder head assembly, for Perkins A3-152 regular injection engine (injectors vertical in cylinder head). Head assembly includes valves & valve parts. Tractors: MF35, MF50; industrials: 35 utility, 203, 205. Replaces ZZ080058, 743272M91. MF-1-19

1 ENGINES Industrial Tractor: 203 (prior to tractor s/n 659002115), 205 (prior to tractor s/n 659002115), 35 Utility Tractor: FE35, MF35, MF50 A3-152 152 CID 3 Cylinder Perkins Diesel Standard Bore 3.6".150 Sleeve Flange thickness Injectors Vertical in Head BEKP1336D-LCB TRU-POWER Engine Kits Used engine s/n 1935854 & up (.150" sleeve flange thickness). Engine bearings & thrust washers must be ordered separately. Basic engine kit. Contains sleeves (.150" sleeve flange thickness), pistons, rings, pins, pin bushings, and complete gasket set with crankshaft seals. 739043M1 734460M91 836325M91 Cylinder Parts Sleeve, CAST, replacing original CAST sleeve. Flange thickness.150". Replaces 734175M1. Piston with pin, flat head. Ring set, for 1 piston, used with CAST sleeves only. 2 @ 3/32", 1 @ 1/8", and 2 @ 1/4" EOK1336D-LCB Engine overhaul kit. Contains sleeves (.150" sleeve flange thickness), pistons, rings, pins, pin bushings, overhaul gasket set with crankshaft seals, valves, springs, guides, retainers, and keys. BIFP1336D Basic in-frame kit. Contains sleeves (.150" sleeve flange thickness), pistons, rings, pins, valve grind set, and oil pan gasket kit. Sleeve & Piston Kit 740407M1 Bushing, piston pin (3 used per engine) Gaskets PK336D Complete for 1 engine Flat head piston Sleeve & piston kit. Contains CAST sleeves, flange thickness.150", pistons & rings, pins & retainers. Complete for 3-cylinders. 747166M91 735232M92 MF3152PG Lower engine gaskets are for engines using 2 piece rope-type rear seal. Seals are included in engine kits but are not included in gasket sets. Top engine set. Bottom engine set (s/n 19B8552 & up) *seal not included Oil pan gasket. MF-1-20

1 ENGINES Industrial Tractor: 203 (prior to tractor s/n 659002115), 205 (prior to tractor s/n 659002115), 35 Utility Tractor: FE35, MF35, MF50 A3-152 152 CID 3 Cylinder Perkins Diesel Standard Bore 3.6".150 Sleeve Flange thickness Injectors Vertical in Head Thrust Washers Crankshaft Kits 735112M1 Thrust washer, upper. 2 used per engine. 735113M1 Thrust washer, lower, tabbed. 2 used per engine. 3638309M91 Crankshaft kit, new, with standard rod bearings, main bearings, & thrust washers. For Perkins AG3-152 gas, A3-152 & AD3-152 diesels. Uses 2 piece rope-type rear seal. 1/2" wide flywheel flange. Cylinder Heads 3641825M91 Crankshaft kit, new, with standard size rod & main bearings, & thrust washers. For Perkins AG3-152 gas & AD3-152 diesel engines using 1 piece lip-type rear seal, keyed nose, 1-1/2" wide flywheel flange. Replaces U5BG0027, 742827M91, 3637399M91, 3637410M91. Oil Pump Repair Kits 3638632M91 Oil pump assembly for Perkins A3-152 & AD3-152 gas & diesel engines. Replaces 41314178 & 736513M91. 3638321M91 Cylinder head assembly, for Perkins A3-152 regular injection engine (injectors vertical in cylinder head). Head assembly includes valves & valve parts. Tractors: MF35, MF50; industrials: 35 utility, 203, 205. Replaces ZZ080058, 743272M91. MF-1-22

1 ENGINES Replacement parts to fit Crawler: 200, 2244 Forklift: 2200, 2500 (prior to s/n 152UA391044DL) Industrial Tractor: 20, 40 (prior to s/n 152UA391044DL), 2135, 203 (tractor s/n 659002115 & up), 205 (tractor s/n 659002115 & up) Tractor: MF135, MF150, MF235 (with engine s/n ending in "D") Treever: 2200 AD3-152 152 CID 3 Cylinder Perkins Diesel Standard Bore 3.6".150 Flange Thickness Injectors at Angle in Cylinder Head 2 Piece rope-type rear seal TRU-POWER Engine Kits For engines with 2-piece rope-type rear crankshaft seal. Not for engines with serial number ending in L or S. Engines with L s/n ending use lip-type rear seal. Engines with S s/n ending use different pistons, rings, & valves with 35º face angle. Engine bearings & thrust washers must be ordered separately. Sleeve & Piston Kit BEKP1337D-LCB EOK1337D-LCB BIFP1337D Basic engine kit. Contains sleeves, pistons, rings, pins, pin bushings, and overhaul gasket set with crankshaft seals. Engine overhaul kit. Contains sleeves, pistons, rings, pins, pin bushings, overhaul gasket set with crankshaft seals, valves, springs, guides, retainers, and keys. Basic in-frame kit. Contains sleeves, pistons, rings, pins, valve grind set, and oil pan gasket kit. PK337D Complete for one engine..150" flange thickness 5 ring piston Sleeve & piston kit. Contains sleeves, pistons & rings, pins & retainers. Complete for 3-cylinders. Cylinder Parts 739043M1 Sleeve, CAST, replacing original CAST sleeve. Flange thickness.150". Replaces 734175M1. 743824M91 Piston (w/pin), cupped head 836325M91 Ring set, for 1 piston, used with CAST sleeves only. 2 @ 3/32", 1 @ 1/8", and 2 @ 1/4" 740407M1 Bushing, piston pin (3 used per engine) MF-1-23

1 ENGINES Crawler: 200, 2244 Forklift: 2200, 2500 (prior to s/n 152UA391044DL) Industrial Tractor: 20, 40 (prior to s/n 152UA391044DL), 2135, 203 (tractor s/n 659002115 & up), 205 (tractor s/n 659002115 & up) Tractor: MF135, MF150, MF235 (with engine s/n ending in "D") Treever: 2200 AD3-152 152 CID 3 Cylinder Perkins Diesel Standard Bore 3.6".150 Flange Thickness Injectors at Angle in Cylinder Head 2 Piece rope-type rear seal Gaskets Valve Parts Lower engine gaskets are for engines using 2 piece rope-type rear seal. Seals are included in engine kits but are not included in gasket sets. 735018M2 748008M91 735232M92 MF3152PG Head gasket only. Top engine set. Bottom engine set (s/n 19B8552 & up) *seal not included Oil pan gasket. Crankshaft Seals VOKP152A 732811M1 737640M1 732445M1 731153M1 Valve overhaul kit. Contains intake & exhaust valves, springs, keys, & guides. Valve, intake (3 used per engine) Valve, exhaust Guide, intake & exhaust valve Spring, inner, intake & exhaust valve 1851747M1 Seal, front, lip-type. 731154M1 Spring, outer, intake & exhaust valve 731959M1 Retainer, valve spring 731155M1 Key, intake & exhaust valve (12 used per engine) 735866M1 Seal, rear, rope-type. For original production blocks (2 required) MF-1-24

1 ENGINES Replacement parts to fit Crawler: 200, 2244 Forklift: 2200, 2500 (prior to s/n 152UA391044DL) Industrial Tractor: 20, 40 (prior to s/n 152UA391044DL), 2135, 203 (tractor s/n 659002115 & up), 205 (tractor s/n 659002115 & up) Tractor: MF135, MF150, MF235 (with engine s/n ending in "D") Treever: 2200 AD3-152 152 CID 3 Cylinder Perkins Diesel Standard Bore 3.6".150 Flange Thickness Injectors at Angle in Cylinder Head 2 Piece rope-type rear seal Connecting Rod Bearing Kits Thrust Washers 735112M1 Thrust washer, upper. 2 used per engine. 1 kit used per engine. 735113M1 Thrust washer, lower, tabbed. 2 used per engine. 737070M91 Rod bearing kit, standard 737071M91 737072M91 Rod bearing kit,.010" Rod bearing kit,.020" Crankshaft Kits 737073M91 Rod bearing kit,.030" Main Bearing Kits 3638309M91 Crankshaft kit, new, with standard rod bearings, main bearings, & thrust washers. For Perkins AG3-152 gas, A3-152 & AD3-152 diesels. Uses 2 piece rope-type rear seal. 1/2" wide flywheel flange. 746156M91 746157M91 746158M91 1 kit used per engine (Thrust washers not included) Main bearing kit, standard Main bearing kit,.010" Main bearing kit,.020" 3641825M91 Crankshaft kit, new, with standard size rod & main bearings, & thrust washers. For Perkins AG3-152 gas & AD3-152 diesel engines using 1 piece lip-type rear seal, keyed nose, 1-1/2" wide flywheel flange. Replaces U5BG0027, 742827M91, 3637399M91, 3637410M91. 746159M91 Main bearing kit,.030" MF-1-25

1 ENGINES Crawler: 200, 2244 Forklift: 2200, 2500 (prior to s/n 152UA391044DL) Industrial Tractor: 20, 40 (prior to s/n 152UA391044DL), 2135, 203 (tractor s/n 659002115 & up), 205 (tractor s/n 659002115 & up) Tractor: MF135, MF150, MF235 (with engine s/n ending in "D") Treever: 2200 AD3-152 152 CID 3 Cylinder Perkins Diesel Standard Bore 3.6".150 Flange Thickness Injectors at Angle in Cylinder Head 2 Piece rope-type rear seal Cylinder Heads 3637389M91 3638632M91 Cylinder head assembly, for Perkins AD3-152 direct injection engines (injectors at angle in cylinder head). Includes valves & valve parts. For tractors: MF135, MF150, MF230, MF235, MF245; industrials: 20, 20C 30B, 30D, 40, 203, 205, 2135, 2200 treever; forklifts: 2200, 2500, 4500; crawlers: 200, 200B, 200C, 2244. Replaces cylinder heads 737704M91, 740595M91, 743201M91, these heads have valves with a 45 degree face angle & are no longer supplied by OEM. 3637389M91 is the same as supplied by the OEM & has valves with a 35 degree face angle. Replaces ZZ080082, ZZ080025, 747574M91. Oil Pump Repair Kits Oil pump assembly for Perkins A3-152 & AD3-152 gas & diesel engines. Replaces 41314178 & 736513M91. MF-1-26

1 ENGINES Replacement parts to fit Crawler: 200B Forklift: 2500 (s/n 152UA391044DL & up), 4500 Industrial Tractor: 20, 40 (with engine s/n 152UA391044DL & up) Tractor: MF230, MF235 (with engine s/n ending in "DL") AD3-152 152 CID 3 Cylinder Perkins Diesel Standard Bore 3.6".150 Flange Thickness Injectors at Angle in Cylinder Head With lip type rear seal BEKP2337-LCB TRU-POWER Engine Kits For engines with 1 piece lip type rear seal. For engines with s/n ending in DL. Not for engines with S in s/n ending. Engines with S s/n ending use different pistons, rings, & have valves with a 35º face angle. Engine bearings & thrust washers must be ordered separately. Basic engine kit. Contains sleeves, pistons, rings, pins, pin bushings, and overhaul gasket set with crankshaft seals. 739043M1 743824M91 836325M91 740407M1 Cylinder Parts Sleeve, CAST, replacing original CAST sleeve. Flange thickness.150". Replaces 734175M1. Piston (w/pin), cupped head Ring set, for 1 piston, used with CAST sleeves only. 2 @ 3/32", 1 @ 1/8", and 2 @ 1/4" Bushing, piston pin (3 used per engine) EOK2337-LCB BIFP1337D Engine overhaul kit. Contains sleeves, pistons, rings, pins, pin bushings, overhaul gasket set with crankshaft seals, valves, springs, guides, retainers, and keys. Basic in-frame kit. Contains sleeves, pistons, rings, pins, valve grind set, and oil pan gasket kit. Gaskets Sleeve & Piston Kit Lower engine gaskets are for engines using 1 piece lip type rear crankshaft seal. Crankshaft seals are included in engine kits but are not included in gasket sets. PK337D Complete for one engine..150" flange thickness 5 ring piston Sleeve & piston kit. Contains sleeves, pistons & rings, pins & retainers. Complete for 3-cylinders. 735018M2 748008M91 747186M91 MF3152PG Head gasket only. Top engine set. Bottom engine set, for engines with serial number ending in DLS with lip type rear seal. *seal not included Oil pan gasket. MF-1-27

1 ENGINES Crawler: 200B Forklift: 2500 (s/n 152UA391044DL & up), 4500 Industrial Tractor: 20, 40 (with engine s/n 152UA391044DL & up) Tractor: MF230, MF235 (with engine s/n ending in "DL") AD3-152 152 CID 3 Cylinder Perkins Diesel Standard Bore 3.6".150 Flange Thickness Injectors at Angle in Cylinder Head With lip type rear seal Crankshaft Seals Connecting Rod Bearing Kits 1851747M1 Seal, front, lip-type. 1447049M91 Seal, rear, lip-type (s/n 248UA123424L & up). For replacement blocks (2 required) Valve Parts 737070M91 1 kit used per engine. Rod bearing kit, standard 737071M91 Rod bearing kit,.010" 737072M91 Rod bearing kit,.020" 737073M91 Rod bearing kit,.030" Main Bearing Kits VOKP152A Valve overhaul kit. Contains intake & exhaust valves, springs, keys, & guides. 732811M1 Valve, intake (3 used per engine) 737640M1 Valve, exhaust 732445M1 731153M1 731154M1 731959M1 731155M1 Guide, intake & exhaust valve Spring, inner, intake & exhaust valve Spring, outer, intake & exhaust valve Retainer, valve spring Key, intake & exhaust valve (12 used per engine) 746156M91 746157M91 746158M91 746159M91 1 kit used per engine (Thrust washers not included) Main bearing kit, standard Main bearing kit,.010" Main bearing kit,.020" Main bearing kit,.030" MF-1-28

1 ENGINES Replacement parts to fit Crawler: 200B Forklift: 2500 (s/n 152UA391044DL & up), 4500 Industrial Tractor: 20, 40 (with engine s/n 152UA391044DL & up) Tractor: MF230, MF235 (with engine s/n ending in "DL") AD3-152 152 CID 3 Cylinder Perkins Diesel Standard Bore 3.6".150 Flange Thickness Injectors at Angle in Cylinder Head With lip type rear seal Thrust Washers Crankshaft Kits 735112M1 Thrust washer, upper. 2 used per engine. 735113M1 Thrust washer, lower, tabbed. 2 used per engine. 3638309M91 Crankshaft kit, new, with standard rod bearings, main bearings, & thrust washers. For Perkins AG3-152 gas, A3-152 & AD3-152 diesels. Uses 2 piece rope-type rear seal. 1/2" wide flywheel flange. Cylinder Heads 3641825M91 Crankshaft kit, new, with standard size rod & main bearings, & thrust washers. For Perkins AG3-152 gas & AD3-152 diesel engines using 1 piece lip-type rear seal, keyed nose, 1-1/2" wide flywheel flange. Replaces U5BG0027, 742827M91, 3637399M91, 3637410M91. Oil Pump Repair Kits 3637389M91 Cylinder head assembly, for Perkins AD3-152 direct injection engines (injectors at angle in cylinder head). Includes valves & valve parts. For tractors: MF135, MF150, MF230, MF235, MF245; industrials: 20, 20C 30B, 30D, 40, 203, 205, 2135, 2200 treever; forklifts: 2200, 2500, 4500; crawlers: 200, 200B, 200C, 2244. Replaces cylinder heads 737704M91, 740595M91, 743201M91, these heads have valves with a 45 degree face angle & are no longer supplied by OEM. 3637389M91 is the same as supplied by the OEM & has valves with a 35 degree face angle. Replaces ZZ080082, ZZ080025, 747574M91. 3638632M91 Oil pump assembly for Perkins A3-152 & AD3-152 gas & diesel engines. Replaces 41314178 & 736513M91. MF-1-29

1 ENGINES Industrial Tractor: 20C, 30B Tractor: MF235, MF245 AD3-152 Direct Injection 152 CID 3 Cylinder Perkins Diesel Standard Bore 3.6".150 Flange Thickness Injectors at Angle in Cylinder Head 35 degree face angle valves 2 Piece rope-type rear seal For engine s/n ending in S. These engines are different from AD3-152 without S or LS ending. Pistons & rings differ in compression ring; intake & exhaust valves differ in face angle BEKP152DS-LCB EOK152DS-LCB BIFP152DS TRU-POWER Engine Kits For engines with serial number ending in DS. Bottom gasket set in this kit is for engine with 2 piece rope type rear seal. Engine bearings & thrust washers must be ordered separately. Basic engine kit. Contains sleeves, pistons, rings, pins, pin bushings, and overhaul gasket set with crankshaft seals. Engine overhaul kit. Contains sleeves, pistons, rings, pins, pin bushings, overhaul gasket set with crankshaft seals, valves, springs, guides, retainers, and keys. Basic in-frame kit. Contains sleeves, pistons, rings, pins, valve grind set, and oil pan gasket kit. Sleeve & Piston Kit 739043M1 745826M91 740407M1 Cylinder Parts Sleeve, CAST, replacing original CAST sleeve. Flange thickness.150". Replaces 734175M1. Ring set, for 1 piston, use with CAST sleeves only. 3 @ 3/32", 1 @ 3/16" Bushing, piston pin (3 used per engine) Gaskets Lower engine gaskets are for engines using 2 piece rope-type rear seal. Seals are included in engine kits but are not included in gasket sets. 735018M2 Head gasket only. 748008M91 Top engine set. 735232M92 Bottom engine set (s/n 19B8552 & up) *seal not included Complete for 1 engine.150" flange thickness 4 ring piston MF3152PG 1851747M1 Oil pan gasket. Crankshaft Seals Seal, front, lip-type. PK152S Sleeve & piston kit. Contains sleeves, pistons, rings, pins & retainers. Complete for 3-cylinders. 735866M1 Seal, rear, rope-type. For original production blocks (2 required) MF-1-30

1 ENGINES Replacement parts to fit Industrial Tractor: 20C, 30B Tractor: MF235, MF245 AD3-152 Direct Injection 152 CID 3 Cylinder Perkins Diesel Standard Bore 3.6".150 Flange Thickness Injectors at Angle in Cylinder Head 35 degree face angle valves 2 Piece rope-type rear seal For engine s/n ending in S. These engines are different from AD3-152 without S or LS ending. Pistons & rings differ in compression ring; intake & exhaust valves differ in face angle Valve Parts Main Bearing Kits VOKP152B 739060M1 747581M1 732445M1 731154M1 731155M1 Valve overhaul kit. Contains intake & exhaust valves, springs, keys, & guides. Valve, intake, 35º face angle Valve, exhaust, 35 face angle Guide, intake & exhaust valve Spring, outer, intake & exhaust valve Key, intake & exhaust valve (12 used per engine) Connecting Rod Bearing Kits 746156M91 746157M91 746158M91 746159M91 735112M1 1 kit used per engine (Thrust washers not included) Main bearing kit, standard Main bearing kit,.010" Main bearing kit,.020" Main bearing kit,.030" Thrust Washers Thrust washer, upper. 2 used per engine. 735113M1 Thrust washer, lower, tabbed. 2 used per engine. 1 kit used per engine. 737070M91 Rod bearing kit, standard 737071M91 Rod bearing kit,.010" 737072M91 Rod bearing kit,.020" 737073M91 Rod bearing kit,.030" MF-1-31

1 ENGINES Industrial Tractor: 20C, 30B Tractor: MF235, MF245 AD3-152 Direct Injection 152 CID 3 Cylinder Perkins Diesel Standard Bore 3.6".150 Flange Thickness Injectors at Angle in Cylinder Head 35 degree face angle valves 2 Piece rope-type rear seal For engine s/n ending in S. These engines are different from AD3-152 without S or LS ending. Pistons & rings differ in compression ring; intake & exhaust valves differ in face angle Cylinder Heads Oil Pump Repair Kits 3638632M91 Oil pump assembly for Perkins A3-152 & AD3-152 gas & diesel engines. Replaces 41314178 & 736513M91. 3637389M91 Cylinder head assembly, for Perkins AD3-152 direct injection engines (injectors at angle in cylinder head). Includes valves & valve parts. For tractors: MF135, MF150, MF230, MF235, MF245; industrials: 20, 20C 30B, 30D, 40, 203, 205, 2135, 2200 treever; forklifts: 2200, 2500, 4500; crawlers: 200, 200B, 200C, 2244. Replaces cylinder heads 737704M91, 740595M91, 743201M91, these heads have valves with a 45 degree face angle & are no longer supplied by OEM. 3637389M91 is the same as supplied by the OEM & has valves with a 35 degree face angle. Replaces ZZ080082, ZZ080025, 747574M91. Crankshaft Kits 3638309M91 Crankshaft kit, new, with standard rod bearings, main bearings, & thrust washers. For Perkins AG3-152 gas, A3-152 & AD3-152 diesels. Uses 2 piece rope-type rear seal. 1/2" wide flywheel flange. 3641825M91 Crankshaft kit, new, with standard size rod & main bearings, & thrust washers. For Perkins AG3-152 gas & AD3-152 diesel engines using 1 piece lip-type rear seal, keyed nose, 1-1/2" wide flywheel flange. Replaces U5BG0027, 742827M91, 3637399M91, 3637410M91. MF-1-32

1 ENGINES Replacement parts to fit Industrial Tractor: 20C, 30B Tractor: MF235, MF245 AD3-152 Direct Injection 152 CID 3 Cylinder Perkins Diesel Standard Bore 3.6".150 Flange Thickness Injectors at Angle in Cylinder Head 35 degree face angle valves With lip type rear seal BEKP152DLS-LCB EOK152DLS-LCB BIFP152DS TRU-POWER Engine Kits For engines with serial number ending in DLS. Bottom gasket set in this kit is for engine with lip-type rear seal. Engine bearings & thrust washers must be ordered separately. Basic engine kit. Contains sleeves, pistons, rings, pins, pin bushings, and overhaul gasket set with crankshaft seals. Engine overhaul kit. Contains sleeves, pistons, rings, pins, pin bushings, overhaul gasket set with crankshaft seals, valves, springs, guides, retainers, and keys. Basic in-frame kit. Contains sleeves, pistons, rings, pins, valve grind set, and oil pan gasket kit. Sleeve & Piston Kit 739043M1 745826M91 740407M1 Cylinder Parts Sleeve, CAST, replacing original CAST sleeve. Flange thickness.150". Replaces 734175M1. Ring set, for 1 piston, use with CAST sleeves only. 3 @ 3/32", 1 @ 3/16" Bushing, piston pin (3 used per engine) Gaskets Lower engine gaskets are for engines using 1 piece lip type rear crankshaft seal. Crankshaft seals are included in engine kits but are not included in gasket sets. 735018M2 Head gasket only. 748008M91 Top engine set. Complete for 1 engine.150" flange thickness 4 ring piston 747186M91 MF3152PG Bottom engine set, for engines with serial number ending in DLS with lip type rear seal. *seal not included Oil pan gasket. Crankshaft Seals PK152S Sleeve & piston kit. Contains sleeves, pistons, rings, pins & retainers. Complete for 3-cylinders. 1851747M1 Seal, front, lip-type. 1447049M91 Seal, rear, lip-type (s/n 248UA123424L & up). For replacement blocks (2 required) MF-1-33

1 ENGINES Industrial Tractor: 20C, 30B Tractor: MF235, MF245 AD3-152 Direct Injection 152 CID 3 Cylinder Perkins Diesel Standard Bore 3.6".150 Flange Thickness Injectors at Angle in Cylinder Head 35 degree face angle valves With lip type rear seal Valve Parts Connecting Rod Bearing Kits VOKP152B 739060M1 747581M1 732445M1 731154M1 731155M1 Valve overhaul kit. Contains intake & exhaust valves, springs, keys, & guides. Valve, intake, 35º face angle Valve, exhaust, 35 face angle Guide, intake & exhaust valve Spring, outer, intake & exhaust valve Key, intake & exhaust valve (12 used per engine) Thrust Washers 737070M91 737071M91 737072M91 737073M91 1 kit used per engine. Rod bearing kit, standard Rod bearing kit,.010" Rod bearing kit,.020" Rod bearing kit,.030" Main Bearing Kits 735112M1 Thrust washer, upper. 2 used per engine. 735113M1 Thrust washer, lower, tabbed. 2 used per engine. 1 kit used per engine (Thrust washers not included) 746156M91 Main bearing kit, standard 746157M91 Main bearing kit,.010" 746158M91 Main bearing kit,.020" 746159M91 Main bearing kit,.030" MF-1-34

1 ENGINES Replacement parts to fit Tractor: MF250 152 CID 3 Cylinder Perkins Diesel Standard Bore 3.6" Engine Serial Number: Engine S/N prefix CE22488U Only 68332 Perkins piston.150 Flange Thickness Injectors at Angle in Cylinder Head BEKP2337-LCB TRU-POWER Engine Kits Basic engine kit. Contains sleeves, pistons, rings, pins, pin bushings, and overhaul gasket set with crankshaft seals. Gasket Sets & Crankshaft Seals BIFP1337D Basic in-frame kit. Contains sleeves, pistons, rings, pins, valve grind set, and oil pan gasket kit. Sleeve and Piston Kit 735018M2 Head gasket only. 748008M91 Top engine set. 747186M91 Bottom engine set, for engines with serial number ending in DLS with lip type rear seal. *seal not included PK337D Complete for 1 engine (Engine uses Perkins piston #68332)..150" flange thickness 5 ring piston Sleeve & piston kit. Contains sleeves, pistons & rings, pins & retainers. Complete for 3-cylinders. MF3152PG 1851747M1 1447049M91 Oil pan gasket. Seal, front, lip-type. Seal, rear, lip-type (s/n 248UA123424L & up). For replacement blocks (2 required) Connecting Rod Bearing Kits Cylinder Parts 739043M1 Sleeve, CAST, replacing original CAST sleeve. Flange thickness.150". Replaces 734175M1. 743824M91 Piston (w/pin), cupped head 836325M91 Ring set, for 1 piston, used with CAST sleeves only. 2 @ 3/32", 1 @ 1/8", and 2 @ 1/4" 1 kit used per engine. 737070M91 Rod bearing kit, standard 737071M91 Rod bearing kit,.010" 737072M91 Rod bearing kit,.020" 740407M1 Bushing, piston pin (3 used per engine) 737073M91 Rod bearing kit,.030" MF-1-35

1 ENGINES Tractor: MF250 152 CID 3 Cylinder Perkins Diesel Standard Bore 3.6" Engine Serial Number: Engine S/N prefix CE22488U Only 68332 Perkins piston.150 Flange Thickness Injectors at Angle in Cylinder Head Main Bearing Kits Crankshaft Kits 746156M91 746157M91 746158M91 746159M91 735112M1 1 kit used per engine (Thrust washers not included) Main bearing kit, standard Main bearing kit,.010" Main bearing kit,.020" Main bearing kit,.030" Thrust Washers Thrust washer, upper. 2 used per engine. 3638309M91 3641825M91 3638632M91 Crankshaft kit, new, with standard rod bearings, main bearings, & thrust washers. For Perkins AG3-152 gas, A3-152 & AD3-152 diesels. Uses 2 piece rope-type rear seal. 1/2" wide flywheel flange. Crankshaft kit, new, with standard size rod & main bearings, & thrust washers. For Perkins AG3-152 gas & AD3-152 diesel engines using 1 piece lip-type rear seal, keyed nose, 1-1/2" wide flywheel flange. Replaces U5BG0027, 742827M91, 3637399M91, 3637410M91. Oil Pump Repair Kits Oil pump assembly for Perkins A3-152 & AD3-152 gas & diesel engines. Replaces 41314178 & 736513M91. 735113M1 Thrust washer, lower, tabbed. 2 used per engine. MF-1-36

1 ENGINES Replacement parts to fit Tractor: MF250 152 CID 3 Cylinder Perkins Diesel Standard Bore 3.6" Engine Serial Number: Engine S/N prefix CE31089U Only 89214 Perkins piston.150 Flange Thickness Injectors at Angle in Cylinder Head BEKP152DLS-LCB TRU-POWER Engine Kits Basic engine kit. Contains sleeves, pistons, rings, pins, pin bushings, and overhaul gasket set with crankshaft seals. Gasket Sets & Crankshaft Seals BIFP152DS Basic in-frame kit. Contains sleeves, pistons, rings, pins, valve grind set, and oil pan gasket kit. Sleeve & Piston Kit 735018M2 748008M91 Head gasket only. Top engine set. 747186M91 Bottom engine set, for engines with serial number ending in DLS with lip type rear seal. *seal not included MF3152PG Oil pan gasket. 1851747M1 Seal, front, lip-type. Complete for 1 engine (engine uses 89214 Perkins piston).150" flange thickness 4 ring piston 1447049M91 Seal, rear, lip-type (s/n 248UA123424L & up). For replacement blocks (2 required) Connecting Rod Bearing Kits PK152S Sleeve & piston kit. Contains sleeves, pistons, rings, pins & retainers. Complete for 3-cylinders. Cylinder Parts 739043M1 Sleeve, CAST, replacing original CAST sleeve. Flange thickness.150". Replaces 734175M1. 1 kit used per engine. 745826M91 Ring set, for 1 piston, use with CAST sleeves only. 3 @ 3/32", 1 @ 3/16" 737070M91 737071M91 Rod bearing kit, standard Rod bearing kit,.010" 740407M1 Bushing, piston pin (3 used per engine) 737072M91 737073M91 Rod bearing kit,.020" Rod bearing kit,.030" MF-1-37

1 ENGINES Tractor: MF250 152 CID 3 Cylinder Perkins Diesel Standard Bore 3.6" Engine Serial Number: Engine S/N prefix CE31089U Only 89214 Perkins piston.150 Flange Thickness Injectors at Angle in Cylinder Head Main Bearing Kits Crankshaft Kits 746156M91 746157M91 746158M91 746159M91 735112M1 1 kit used per engine (Thrust washers not included) Main bearing kit, standard Main bearing kit,.010" Main bearing kit,.020" Main bearing kit,.030" Thrust Washers Thrust washer, upper. 2 used per engine. 3638309M91 3641825M91 3638632M91 Crankshaft kit, new, with standard rod bearings, main bearings, & thrust washers. For Perkins AG3-152 gas, A3-152 & AD3-152 diesels. Uses 2 piece rope-type rear seal. 1/2" wide flywheel flange. Crankshaft kit, new, with standard size rod & main bearings, & thrust washers. For Perkins AG3-152 gas & AD3-152 diesel engines using 1 piece lip-type rear seal, keyed nose, 1-1/2" wide flywheel flange. Replaces U5BG0027, 742827M91, 3637399M91, 3637410M91. Oil Pump Repair Kits Oil pump assembly for Perkins A3-152 & AD3-152 gas & diesel engines. Replaces 41314178 & 736513M91. 735113M1 Thrust washer, lower, tabbed. 2 used per engine. MF-1-38

1 ENGINES Replacement parts to fit Industrial Tractor: 356 Tractor Shovel Tractor: MF65 A4-203 Regular Injection 203 CID 4 Cylinder Perkins Diesel Standard Bore 3.6".040 Sleeve Flange Thickness Injectors Vertical in Head BEKP1465D-LCB EOK1465D-LCB BIFP1465D TRU-POWER Engine Kits Used prior to engine s/n 2820092 (.040" sleeve flange thickness). Engine bearings and thrust washers must be ordered separately. Basic engine kit. Contains sleeves, pistons, rings, pins, pin bushings, and overhaul gasket set with crankshaft seals. Engine overhaul kit. Contains sleeves, pistons, rings, pins, pin bushings, overhaul gasket set with crankshaft seals, valves, springs, guides, retainers, and keys. Basic in-frame kit. Contains sleeve and piston kit with rings, pins, and retainers, top engine gasket set, and oil pan gasket. 732638M-CST 734460M91 PRS462DC 836325M91 740407M1 Cylinder Parts Sleeve, CAST, for replacing original CHROME sleeve. Flange thickness.040". Piston with pin, flat head. Ring set, use with CHROME sleeves only. 2 @ 3/32", 1 @ 1/8", 2 @ 1/4" Ring set, for 1 piston, used with CAST sleeves only. 2 @ 3/32", 1 @ 1/8", and 2 @ 1/4" Bushing, piston pin (4 used per engine) Sleeve & Piston Kit Gaskets Crankshaft seals are included in engine kits but are not included in gasket sets. 746051M91 Top engine set. PK462DC Complete for 1 engine Flat head piston Sleeve and piston kit, with original style 732638M1 CHROME sleeves, flange thickness.040". Contains piston, sleeves, pins, locks and rings. Sleeves not available separately. 743029M91 MF4203PG 1851747M1 Bottom engine set. Oil pan gasket. Crankshaft Seals Seal, front, lip-type. PK465D Sleeve and piston kit, with CAST sleeves, for replacing original style chrome sleeves. Flange.040". Contains piston, sleeves, pins, locks and rings. 735866M1 Seal, rear, rope-type. For original production blocks (2 required) MF-1-39

1 ENGINES Industrial Tractor: 356 Tractor Shovel Tractor: MF65 A4-203 Regular Injection 203 CID 4 Cylinder Perkins Diesel Standard Bore 3.6".040 Sleeve Flange Thickness Injectors Vertical in Head Valve Parts Connecting Rod Bearing Kits 1 kit used per engine. 737066M91 Rod bearing kit, standard VOKP203 731151M1 731152M1 732445M1 Valve overhaul kit. Contains intake and exhaust valves, springs, keys, and guides. Valve, intake Valve, exhaust Guide, intake & exhaust valve 737067M91 737068M91 737069M91 Rod bearing kit,.010" Rod bearing kit,.020" Rod bearing kit,.030" Main Bearing Kits 731153M1 Spring, inner, intake & exhaust valve 731154M1 Spring, outer, intake & exhaust valve 731959M1 Retainer, valve spring 731155M1 735112M1 Key, intake & exhaust valves, pair (16 used per engine) Thrust Washers Thrust washer, upper. 2 used per engine. 745405M91 745406M91 745407M91 1 kit used per engine (Thrust washers not included) Main bearing kit, standard Main bearing kit,.010" Main bearing kit,.020" 745408M91 Main bearing kit,.030" 735113M1 Thrust washer, lower, tabbed. 2 used per engine. Crankshaft Kits 3638473M91 Crankshaft kit for A4-203 & AD4-203 Perkins Diesels using 2 piece rope-type rear seal. Shaft not splined on gear end. MF-1-40

1 ENGINES Replacement parts to fit Industrial Tractor: 356 Tractor Shovel Tractor: MF65 A4-203 Regular Injection 203 CID 4 Cylinder Perkins Diesel Standard Bore 3.6".150 Sleeve Flange Thickness Injectors Vertical in Head BEKP1466D-LCB EOK1466D-LCB TRU-POWER Engine Kits Used engine s/n 2820092 & up (.150" sleeve flange thickness). Engine bearings and thrust washers must be ordered separately. Basic engine kit. Contains sleeves, pistons, rings, pins, pin bushings, and overhaul gasket set with crankshaft seals. Engine overhaul kit. Contains sleeves, pistons, rings, pins, pin bushings, overhaul gasket set with crankshaft seals, valves, springs, guides, retainers, and keys. 739043M1 734460M91 836325M91 740407M1 Cylinder Parts Sleeve, CAST, replacing original CAST sleeve. Flange thickness.150". Replaces 734175M1. Piston with pin, flat head. Ring set, for 1 piston, used with CAST sleeves only. 2 @ 3/32", 1 @ 1/8", and 2 @ 1/4" Bushing, piston pin (4 used per engine) BIFP1466D Basic in-frame kit. Contains sleeve and piston kit with rings, pins and retainers, top engine gasket set, and oil pan gasket. Gaskets Sleeve & Piston Kit Crankshaft seals are included in engine kits but are not included in gasket sets. PK466D Flat head piston Sleeve and piston kit. Contains CAST sleeves, flange thickness,.150", pistons and rings, pin and retainers. 746051M91 743029M91 MF4203PG Top engine set. Bottom engine set. Oil pan gasket. Crankshaft Seals 1851747M1 Seal, front, lip-type. 735866M1 Seal, rear, rope-type. For original production blocks (2 required) MF-1-41

1 ENGINES Industrial Tractor: 356 Tractor Shovel Tractor: MF65 A4-203 Regular Injection 203 CID 4 Cylinder Perkins Diesel Standard Bore 3.6".150 Sleeve Flange Thickness Injectors Vertical in Head Valve Parts Oil Pump Repair Kits 3638633M91 Oil pump assembly for Perkins A4-203 & AD4-203 gas & diesel engines. Replaces 41314164, 736617M91. Main Bearing Kits VOKP203 Valve overhaul kit. Contains intake and exhaust valves, springs, keys, and guides. 731151M1 731152M1 732445M1 731153M1 731154M1 731959M1 731155M1 Valve, intake Valve, exhaust Guide, intake & exhaust valve Spring, inner, intake & exhaust valve Spring, outer, intake & exhaust valve Retainer, valve spring Key, intake & exhaust valves, pair (16 used per engine) Connecting Rod Bearing Kits 745405M91 745406M91 745407M91 745408M91 735112M1 1 kit used per engine (Thrust washers not included) Main bearing kit, standard Main bearing kit,.010" Main bearing kit,.020" Main bearing kit,.030" Thrust Washers Thrust washer, upper. 2 used per engine. 735113M1 Thrust washer, lower, tabbed. 2 used per engine. 1 kit used per engine. 737066M91 737067M91 Rod bearing kit, standard Rod bearing kit,.010" Crankshaft Kits 737068M91 Rod bearing kit,.020" 737069M91 Rod bearing kit,.030" 3638473M91 Crankshaft kit for A4-203 & AD4-203 Perkins Diesels using 2 piece rope-type rear seal. Shaft not splined on gear end. MF-1-42

1 ENGINES Replacement parts to fit Industrial Tractor: 356 Tractor Shovel Tractor: MF65 AD4-203 Direct Injection 203 CID 4 Cylinder Perkins Diesel Standard Bore 3.6".040 Sleeve Flange Thickness Injectors at Angle in Cylinder Head 2 Piece rope-type rear seal BEKP1464D-LCB EOK1464D-LCB BIFP1464D TRU-POWER Engine Kits Used prior to engine s/n 2939036 (.040" sleeve flange thickness). Engine bearings and thrust washers must be ordered separately. Basic engine kit. Contains sleeves, pistons, rings, pins, pin bushings, and overhaul gasket set with crankshaft seals. Engine overhaul kit. Contains sleeves, pistons, rings, pins, pin bushings, overhaul gasket set with crankshaft seals, valves, springs, guides, and keys. Basic in-frame kit. Contains sleeve and piston kit with rings, pins, and retainers, top engine gasket set, and oil pan gasket. 732638M-CST 743824M91 PRS462DC 836325M91 740407M1 Cylinder Parts Sleeve, CAST, for replacing original CHROME sleeve. Flange thickness.040". Piston (w/pin), cupped head Ring set, use with CHROME sleeves only. 2 @ 3/32", 1 @ 1/8", 2 @ 1/4" Ring set, for 1 piston, used with CAST sleeves only. 2 @ 3/32", 1 @ 1/8", and 2 @ 1/4" Bushing, piston pin (4 used per engine) PK463DC Sleeve and Piston Kit Complete for one engine. Used prior to engine s/n 2939036. For engines originally produced with CHROME sleeves. Sleeve and piston kit. Contains original style 732638M1 CHROME sleeves, flange thickness.040", piston and rings, pin and retainers. Sleeves not available separately. 735349M91 735350M92 MFD4203PG Gaskets For engines using 2 piece rope-type rear seal, NOT for engines with DL in serial number ending. Crankshaft seals are included in engine kits but are not included in gasket sets. Top engine set. Bottom set, to engine s/n 29C1084. Oil pan gasket. Crankshaft Seals PK464D Sleeve and piston kit. Contains CAST sleeves, for replacing original style chrome sleeves, flange thickness,.040", piston and rings, pin and retainers. 1851747M1 Seal, front, lip-type. 735866M1 Seal, rear, rope-type. For original production blocks (2 required) MF-1-43

1 ENGINES Industrial Tractor: 356 Tractor Shovel Tractor: MF65 AD4-203 Direct Injection 203 CID 4 Cylinder Perkins Diesel Standard Bore 3.6".040 Sleeve Flange Thickness Injectors at Angle in Cylinder Head 2 Piece rope-type rear seal Valve Parts Connecting Rod Bearing Kits 1 kit used per engine. VOKP203A 732811M1 737640M1 732445M1 731153M1 731154M1 731959M1 731155M1 Valve overhaul kit. Contains intake and exhaust valves, springs, keys, and guides. Valve, intake (4 used per engine) Valve, exhaust Guide, intake & exhaust valve Spring, inner, intake & exhaust valve Spring, outer, intake & exhaust valve Retainer, valve spring Key, intake & exhaust valves, pair (16 used per engine) Thrust Washers 735113M1 Thrust washer, lower, tabbed. 2 used per engine. 735112M1 Thrust washer, upper. 2 used per engine. 737066M91 737067M91 737068M91 737069M91 745405M91 745406M91 745407M91 745408M91 Rod bearing kit, standard Rod bearing kit,.010" Rod bearing kit,.020" Rod bearing kit,.030" Main Bearing Kits 1 kit used per engine (Thrust washers not included) Main bearing kit, standard Main bearing kit,.010" Main bearing kit,.020" Main bearing kit,.030" Crankshaft Kits 3638473M91 Crankshaft kit for A4-203 & AD4-203 Perkins Diesels using 2 piece rope-type rear seal. Shaft not splined on gear end. MF-1-44

1 ENGINES Replacement parts to fit Combine: 300 Industrial Tractor: 356, 302, 304, 3165 Tractor: MF65, MF165 AD4-203 Direct Injection 203 CID 4 Cylinder Perkins Diesel Standard Bore 3.6".150 Sleeve Flange Thickness Injectors at Angle in Cylinder Head 2 Piece rope-type rear seal TRU-POWER Engine Kits Used engine s/n 2939036 to 29C1084 (.150" Sleeve Flange Thickness). For engines using 2 piece rope type rear seal. Engines bearings and thrust washers must be ordered separately. 739043M1 743824M91 Cylinder Parts Sleeve, CAST, replacing original CAST sleeve. Flange thickness.150". Replaces 734175M1. Piston (w/pin), cupped head BEKP1467D-LCB EOK1467D-LCB BIFP1467D Basic engine kit. Contains sleeves, pistons, rings, pins, pin bushings, and overhaul gasket set with crankshaft seals. Engine overhaul kit. Contains sleeves, pistons, rings, pins, pin bushings, overhaul gasket set with crankshaft seals, valves, springs, guides, and keys. Basic in-frame kit. Contains sleeve and piston kit with rings, pins, and retainers, top engine gasket set, and oil pan gasket. Sleeve and Piston Kit 836325M91 740407M1 Ring set, for 1 piston, used with CAST sleeves only. 2 @ 3/32", 1 @ 1/8", and 2 @ 1/4" Bushing, piston pin (4 used per engine) Gaskets For engines using 2 piece rope-type rear seal, NOT for engines with DL in serial number ending. Crankshaft seals are included in engine kits but are not included in gasket sets. 735349M91 Top engine set. 735350M92 Bottom set, to engine s/n 29C1084. Complete for one engine. Used engine s/n 2939036 & up. For engines originally produced with CAST sleeves. MFD4203PG Oil pan gasket. Crankshaft Seals PK467D Sleeve and piston kit. Contains CAST sleeves, flange thickness.150", piston and rings, pin and retainers. 1851747M1 Seal, front, lip-type. 735866M1 Seal, rear, rope-type. For original production blocks (2 required) MF-1-45

1 ENGINES Combine: 300 Industrial Tractor: 356, 302, 304, 3165 Tractor: MF65, MF165 AD4-203 Direct Injection 203 CID 4 Cylinder Perkins Diesel Standard Bore 3.6".150 Sleeve Flange Thickness Injectors at Angle in Cylinder Head 2 Piece rope-type rear seal Valve Parts Main Bearing Kits 1 kit used per engine (Thrust washers not included) 745405M91 Main bearing kit, standard VOKP203A 732811M1 737640M1 732445M1 Valve overhaul kit. Contains intake and exhaust valves, springs, keys, and guides. Valve, intake (4 used per engine) Valve, exhaust Guide, intake & exhaust valve 745406M91 745407M91 745408M91 Main bearing kit,.010" Main bearing kit,.020" Main bearing kit,.030" Thrust Washers 731153M1 Spring, inner, intake & exhaust valve 731154M1 Spring, outer, intake & exhaust valve 731959M1 Retainer, valve spring 731155M1 Key, intake & exhaust valves, pair (16 used per engine) Connecting Rod Bearing Kits 735112M1 735113M1 Thrust washer, upper. 2 used per engine. Thrust washer, lower, tabbed. 2 used per engine. Crankshaft Kits 1 kit used per engine. 737066M91 Rod bearing kit, standard 737067M91 737068M91 737069M91 Rod bearing kit,.010" Rod bearing kit,.020" Rod bearing kit,.030" 3638473M91 Crankshaft kit for A4-203 & AD4-203 Perkins Diesels using 2 piece rope-type rear seal. Shaft not splined on gear end. MF-1-46

1 ENGINES Replacement parts to fit Combine: 300 Industrial Tractor: 30, 302, 304, 3165, 356 Tractor Shovel, 40B, 50 Tractor: MF165, MF255, MF65 AD4-203 Direct Injection 203 CID 4 Cylinder Perkins Diesel Standard Bore 3.6".150 Sleeve Flange Thickness Injectors at Angle in Cylinder Head Valve spring count can vary, check cylinder head when disassembling BEKP2467-LCB TRU-POWER Engine Kits Used engine s/n 29C1084 & up. (.150" Sleeve Flange Thickness). For Engines using lip-type rear seal or 2 piece rope-type rear seal. Engine bearings and thrust washers must be ordered separately. Basic engine kit. Contains sleeves, pistons, rings, pins, pin bushings, and overhaul gasket set with crankshaft seals. 740407M1 Bushing, piston pin (4 used per engine) Gaskets EOK2467-LCB Engine overhaul kit. Contains sleeves, pistons, rings, pins, pin bushings, overhaul gasket set with crankshaft seals, valves, springs, guides, retainers, and keys. BIFP1467D PK467D Basic in-frame kit. Contains sleeve and piston kit with rings, pins, and retainers, top engine gasket set, and oil pan gasket. Sleeve and Piston Kit Complete for one engine. Used engine s/n 2939036 & up. For engines originally produced with CAST sleeves. Sleeve and piston kit. Contains CAST sleeves, flange thickness.150", piston and rings, pin and retainers. 735349M91 745987M91 MFD4203PG Crankshaft seals are included in engine kits but are not included in gasket sets. Top engine set. Bottom set, engine s/n 29C1084 & up Oil pan gasket. Crankshaft Seals Cylinder Parts 739043M1 743824M91 836325M91 Sleeve, CAST, replacing original CAST sleeve. Flange thickness.150". Replaces 734175M1. Piston (w/pin), cupped head Ring set, for 1 piston, used with CAST sleeves only. 2 @ 3/32", 1 @ 1/8", and 2 @ 1/4" 1851747M1 735866M1 1447049M91 Seal, front, lip-type. Seal, rear, rope-type. For original production blocks (2 required) Seal, rear, lip-type (s/n 248UA123424L & up). For replacement blocks (2 required) MF-1-47

1 ENGINES Combine: 300 Industrial Tractor: 30, 302, 304, 3165, 356 Tractor Shovel, 40B, 50 Tractor: MF165, MF255, MF65 AD4-203 Direct Injection 203 CID 4 Cylinder Perkins Diesel Standard Bore 3.6".150 Sleeve Flange Thickness Injectors at Angle in Cylinder Head Valve spring count can vary, check cylinder head when disassembling Valve Parts Main Bearing Kits 1 kit used per engine (Thrust washers not included) 745405M91 Main bearing kit, standard VOKP203A 732811M1 737640M1 732445M1 Valve overhaul kit. Contains intake and exhaust valves, springs, keys, and guides. Valve, intake (4 used per engine) Valve, exhaust Guide, intake & exhaust valve 745406M91 745407M91 745408M91 Main bearing kit,.010" Main bearing kit,.020" Main bearing kit,.030" Thrust Washers 731153M1 Spring, inner, intake & exhaust valve 731154M1 Spring, outer, intake & exhaust valve 731959M1 Retainer, valve spring 731155M1 Key, intake & exhaust valves, pair (16 used per engine) Connecting Rod Bearing Kits 735112M1 735113M1 Thrust washer, upper. 2 used per engine. Thrust washer, lower, tabbed. 2 used per engine. Crankshaft Kits 1 kit used per engine. 3638473M91 Crankshaft kit for A4-203 & AD4-203 Perkins Diesels using 2 piece rope-type rear seal. Shaft not splined on gear end. 737066M91 Rod bearing kit, standard 737067M91 Rod bearing kit,.010" 737068M91 Rod bearing kit,.020" 737069M91 Rod bearing kit,.030" MF-1-48

1 ENGINES Replacement parts to fit Forklift: 6500 (prior to engine s/n 236UA109215L) Industrial Tractor: 31 Tractor: MF175, MF180, MF265 (prior to engine s/n 236UA109215L) A4-236 Direct Injection 236 CID 4 Cylinder Perkins Diesel Standard Bore 3.875" Injectors at Angle in Cylinder Head TRU-POWER Engine Kits Engine bearings and thrust washers must be ordered separately. 733767M1 Bushing, piston pin (4 used per engine) BEKP178-LCB Basic engine kit. Contains sleeves, pistons, rings, pins, pin bushings, and overhaul gasket set with crankshaft seals. Gaskets EOK178-LCB Engine overhaul kit. Contains sleeves, pistons, rings, pins, pin bushings, overhaul gasket set with crankshaft seals, valves, springs, and keys. BIFP178 Basic in-frame kit. Contains sleeve and piston kit with rings, pins and retainers, top engine gasket set, and oil pan gasket. Sleeve & Piston Kit Crankshaft seals are included in engine kits but are not included in gasket sets. 3638661M91 Top engine set. 747191M91 Bottom engine set. 3638519M1 Oil pan gasket. Complete for 1 engine Crankshaft Seals PK78 Sleeve and piston kit. Contains sleeves, piston and rings, pin and retainers. 1447690M1 Seal, front, lip-type. Cylinder Parts 736507M3 735187M91 Cylinder liner. Piston with pin; Oil groove holes 10 top, 12 bottom. 1447049M91 Seal, rear, lip-type (s/n 248UA123424L & up). For replacement blocks (2 required) 836583M91 Ring set, for 1 piston. Can replace 738404M91 & 745769M91. 3 @ 3/32", 2 @ 1/4" 735942M1 Seal, rear, rope-type, 2 required (prior to s/n 248UA123424L) *Both rear seal types included in engine kits MF-1-49

1 ENGINES Forklift: 6500 (prior to engine s/n 236UA109215L) Industrial Tractor: 31 Tractor: MF175, MF180, MF265 (prior to engine s/n 236UA109215L) A4-236 Direct Injection 236 CID 4 Cylinder Perkins Diesel Standard Bore 3.875" Injectors at Angle in Cylinder Head Valve Parts Main Bearing Kits 1 kit used per engine (Thrust washers not included) 735168M91 Main bearing kit, standard VOKP236 739027M1 747552M1 735525M91 Valve overhaul kit. Contains intake and exhaust valves, springs, and keys. Valve, intake Valve, exhaust, stellite. Replaces 741257M1. Spring, inner, intake & exhaust valve 735169M91 735170M91 735171M91 Main bearing kit,.010" Main bearing kit,.020" Main bearing kit,.030" Thrust Washers 735521M1 Spring, outer, intake & exhaust valve 736453M1 Key, intake & exhaust valve (pair) Connecting Rod Bearing Kits Thrust washer, upper. 2 used per engine. Prior to engine s/n 4812575, MF175, MF180 only (lower washer tab on-center). 1 kit used per engine. Thrust washer, lower, 2 used per engine. Prior to engine s/n 4812575, MF175, MF180 only (lower washer tab on-center). 736950M91 736951M91 736952M91 Rod bearing kit, standard Rod bearing kit,.010" Rod bearing kit,.020" 747128M1 Thrust washer, upper. 2 used per engine. MF175, MF180, engine s/n 4812575 and up, All MF265, 31C, 6500 forklift. (lower washer tab off-center) 747129M1 Thrust washer, lower, tabbed. 2 used per engine. MF175, MF180, engine s/n 4812575 and up, All MF265, 31C, 6500 forklift. (lower washer tab off-center) MF-1-50

1 ENGINES Replacement parts to fit Forklift: 6500 (engine s/n 236UA109215L & up) Industrial Tractor: 50C Tractor: MF255, MF265 (engine s/n 236UA109215L & up) A4-236 Direct Injection 236 CID 4 Cylinder Perkins Diesel Standard Bore 3.875" Injectors at Angle in Cylinder Head TRU-POWER Engine Kits Engine bearings and thrust washers must be ordered separately. Gaskets BEKP2178-LCB Basic engine kit. Contains sleeves, pistons, rings, pins, pin bushings, and overhaul gasket set with crankshaft seals. EOK2178-LCB Engine overhaul kit. Contains sleeves, pistons, rings, pins, pin bushings, overhaul gasket set with crankshaft seals, valves, springs, and keys. Crankshaft seals are included in engine kits but are not included in gasket sets. BIFP2178 Basic in-frame kit. Contains sleeve and piston kit with rings, pins, and retainers, top engine gasket set, and oil pan gasket. Sleeve & Piston Kit 3638661M91 747191M91 3638519M1 Top engine set. Bottom engine set. Oil pan gasket. Crankshaft Seals 1447690M1 Seal, front, lip-type. PK79 Sleeve and piston kit. Contains sleeves, piston and rings, pin and retainers. Cylinder Parts 735942M1 Seal, rear, rope-type, 2 required (prior to s/n 248UA123424L) 736507M3 743110M91 Cylinder liner. Piston w/pin; oil groove holes 8 top, 8 bottom. 1447049M91 Seal, rear, lip-type (s/n 248UA123424L & up). For replacement blocks (2 required) *Both rear seal types included in engine kits 836583M91 Ring set, for 1 piston. Can replace 738404M91 & 745769M91. 3 @ 3/32", 2 @ 1/4" 733767M1 Bushing, piston pin (4 used per engine) MF-1-51

1 ENGINES Forklift: 6500 (engine s/n 236UA109215L & up) Industrial Tractor: 50C Tractor: MF255, MF265 (engine s/n 236UA109215L & up) A4-236 Direct Injection 236 CID 4 Cylinder Perkins Diesel Standard Bore 3.875" Injectors at Angle in Cylinder Head Valve Parts Main Bearing Kits 1 kit used per engine (Thrust washers not included) 735168M91 Main bearing kit, standard VOKP236 739027M1 747552M1 735525M91 Valve overhaul kit. Contains intake and exhaust valves, springs, and keys. Valve, intake Valve, exhaust, stellite. Replaces 741257M1. Spring, inner, intake & exhaust valve 735169M91 735170M91 735171M91 Main bearing kit,.010" Main bearing kit,.020" Main bearing kit,.030" Thrust Washers 735521M1 Spring, outer, intake & exhaust valve 736453M1 Key, intake & exhaust valve (pair) Connecting Rod Bearing Kits 747128M1 Thrust washer, upper. 2 used per engine. MF175, MF180, engine s/n 4812575 and up, All MF265, 31C, 6500 forklift. (lower washer tab off-center) 736950M91 736951M91 1 kit used per engine. Rod bearing kit, standard Rod bearing kit,.010" 747129M1 Thrust washer, lower, tabbed. 2 used per engine. MF175, MF180, engine s/n 4812575 and up, All MF265, 31C, 6500 forklift. (lower washer tab off-center) 736952M91 Rod bearing kit,.020" MF-1-52

1 ENGINES Replacement parts to fit Tractor: MF275 A4-248 Direct Injection 248 CID 4 Cylinder Perkins Diesel Standard Bore 3.978" Engine Serial Number: Prefix 248UA or LF---N or LF---U only Injectors at Angle in Cylinder Head BEKP4248-LCB TRU-POWER Engine Kits Engine bearings and thrust washers must be ordered separately. Basic engine kit. Contains sleeves, pistons, rings, pins, pin bushings, and overhaul gasket set with crankshaft seals. Gaskets Crankshaft seals are included in engine kits but are not included in gasket sets. EOK4248-LCB BIFP4248 Engine overhaul kit. Contains sleeves, pistons, rings, pins, pin bushings, overhaul gasket set with crankshaft seals, valves, springs, and keys. Basic in-frame kit. Contains sleeve and piston kit with rings, pins and retainers, top engine gasket set, and oil pan gasket. Sleeve & Piston Kit 3638661M91 747191M91 3638519M1 1447690M1 Top engine set. Bottom engine set. Oil pan gasket. Crankshaft Seals Seal, front, lip-type. Complete for 1 engine 735942M1 Seal, rear, rope-type, 2 required (prior to s/n 248UA123424L) PK4248 Sleeve and piston kit. Contains sleeve, piston and rings, pins and retainers, complete for 4 cylinders. Sleeves replace Perkins #31358352, pistons replace Perkins #89207. Cylinder Parts 1447049M91 Seal, rear, lip-type (s/n 248UA123424L & up). For replacement blocks (2 required) 742466M1 Cylinder sleeve, replace 31358352. *Both rear seal types included in EOK and BEK 740535M91 Ring set, for 1 piston. 3 @ 3/32", 1 @ 1/4" 733767M1 Bushing, piston pin (4 used per engine) MF-1-53

1 ENGINES Tractor: MF275 A4-248 Direct Injection 248 CID 4 Cylinder Perkins Diesel Standard Bore 3.978" Engine Serial Number: Prefix 248UA or LF---N or LF---U only Injectors at Angle in Cylinder Head Valve Parts Main Bearing Kits VOKP236 739027M1 747552M1 735525M91 735521M1 736453M1 Valve overhaul kit. Contains intake and exhaust valves, springs, and keys. Valve, intake Valve, exhaust, stellite. Replaces 741257M1. Spring, inner, intake & exhaust valve Spring, outer, intake & exhaust valve Key, intake & exhaust valve (pair) 735168M91 735169M91 735170M91 735171M91 1 kit used per engine (Thrust washers not included) Main bearing kit, standard Main bearing kit,.010" Main bearing kit,.020" Main bearing kit,.030" Thrust Washers Connecting Rod Bearing Kits 747128M1 Thrust washer, upper. 2 used per engine. MF175, MF180, engine s/n 4812575 and up, All MF265, 31C, 6500 forklift. (lower washer tab off-center) 736950M91 736951M91 1 kit used per engine. Rod bearing kit, standard Rod bearing kit,.010" 747129M1 Thrust washer, lower, tabbed. 2 used per engine. MF175, MF180, engine s/n 4812575 and up, All MF265, 31C, 6500 forklift. (lower washer tab off-center) 736952M91 Rod bearing kit,.020" MF-1-54

1 ENGINES Replacement parts to fit Tractor: MF290, MF294-4, MF690 A4-248 Direct Injection 248 CID 4 Cylinder Perkins Diesel Standard Bore 3.978" Engine Serial Number: Prior to LF---U839080J Injectors at Angle in Cylinder Head TRU-POWER Engine Kits Engine bearings and thrust washers must be ordered separately. Gaskets BEKP4248A-LCB Basic engine kit. Contains sleeves, pistons, rings, pins, pin bushings, and overhaul gasket set with crankshaft seals. EOK4248A-LCB BIFP4248A Engine overhaul kit. Contains sleeves, pistons and rings, pins and retainers, pin bushings, gasket sets, crankshaft seals, intake and exhaust valves, valve keys and springs. Basic in-frame kit. Contains sleeves, pistons, rings, pins, valve grind set, and oil pan gasket. Sleeve & Piston Kit 747169M91 747191M91 3638519M1 Crankshaft seals are included in engine kits but are not included in gasket sets. Top engine set. Bottom engine set. Oil pan gasket. Crankshaft Seals 1447690M1 Seal, front, lip-type. PK4248 Complete for 1 engine Sleeve and piston kit. Contains sleeve, piston and rings, pins and retainers, complete for 4 cylinders. Sleeves replace Perkins #31358352, pistons replace Perkins #89207. Cylinder Parts 1447049M91 Seal, rear, lip-type (s/n 248UA123424L & up). For replacement blocks (2 required) Valve Parts 742466M1 Cylinder sleeve, replace 31358352. 740535M91 Ring set, for 1 piston. 3 @ 3/32", 1 @ 1/4" VOKP236 739027M1 Valve overhaul kit. Contains intake and exhaust valves, springs, and keys. Valve, intake 733767M1 Bushing, piston pin (4 used per engine) 747552M1 735525M91 Valve, exhaust, stellite. Replaces 741257M1. Spring, inner, intake & exhaust valve 735521M1 Spring, outer, intake & exhaust valve 736453M1 Key, intake & exhaust valve (pair) MF-1-55

1 ENGINES Tractor: MF290, MF294-4, MF690 A4-248 Direct Injection 248 CID 4 Cylinder Perkins Diesel Standard Bore 3.978" Engine Serial Number: Prior to LF---U839080J Injectors at Angle in Cylinder Head Connecting Rod Bearing Kits Thrust Washers 1 kit used per engine. 747128M1 Thrust washer, upper. 2 used per engine. MF175, MF180, engine s/n 4812575 and up, All MF265, 31C, 6500 forklift. (lower washer tab off-center) 736950M91 736951M91 736952M91 Rod bearing kit, standard Rod bearing kit,.010" Rod bearing kit,.020" 747129M1 Thrust washer, lower, tabbed. 2 used per engine. MF175, MF180, engine s/n 4812575 and up, All MF265, 31C, 6500 forklift. (lower washer tab off-center) Main Bearing Kits 1 kit used per engine (Thrust washers not included) 735168M91 Main bearing kit, standard 735169M91 Main bearing kit,.010" 735170M91 Main bearing kit,.020" 735171M91 Main bearing kit,.030" MF-1-56

1 ENGINES Replacement parts to fit Combine: 540 Tractor: MF1080, MF1085, MF285 A4-318 Direct Injection 318 CID 4 Cylinder Perkins Diesel Standard Bore 4.5" Injectors at Angle in Cylinder Head BEKP4318-LCB TRU-POWER Engine Kits Engine bearings and thrust washers must be ordered separately. Basic engine kit. Contains sleeves, pistons, rings, pins, pin bushings, and overhaul gasket set with crankshaft seals. Gaskets Crankshaft seals are included in engine kits but are not included in gasket sets. EOK4318-LCB BIFP4318 Engine overhaul kit. Contains sleeves, pistons, rings, pins, pin bushings, overhaul gasket set with crankshaft seals, valves, springs, guides, and keys. Basic in-frame kit. Contains sleeve and piston with rings, pins and retainers, top engine gasket set, and oil pan gasket. Sleeve & Piston Kit 746288M91 743789M91 737047M1 1447024M1 Top set, with head gasket 36812348/745730M1 Bottom set. Oil pan gasket. Crankshaft Seals Seal, front, lip-type. 735942M1 Seal, rear, rope-type, 2 required (prior to s/n 248UA123424L) Complete for 1 engine PK80 Sleeve and piston kit. Contains sleeves, pistons and rings, pins and retainers, complete for 4 cylinders. 1447049M91 Seal, rear, lip-type (s/n 248UA123424L & up). For replacement blocks (2 required) Cylinder Parts 31358534 Cylinder sleeve 745950M1 731463M1 Ring set, for 1 piston. 3 @ 3/32", 1 @ 1/4" Bushing, piston pin (4 used per engine) MF-1-57

1 ENGINES Combine: 540 Tractor: MF1080, MF1085, MF285 A4-318 Direct Injection 318 CID 4 Cylinder Perkins Diesel Standard Bore 4.5" Injectors at Angle in Cylinder Head Valve Parts Main Bearing Kits 1 kit used per engine (Thrust washers not included) 745584M91 Main bearing kit, standard VOKP318 738095M1 738944M91 738094M1 Valve overhaul kit. Contains intake and exhaust valves, springs, keys, and guides. Valve, engine intake Valve, engine exhaust Guide, intake & exhaust valves 745585M91 745586M91 745587M91 Main bearing kit,.010" Main bearing kit,.020" Main bearing kit,.030" Thrust Washers 735525M91 Spring, inner, intake & exhaust valve 735521M1 Spring, outer, intake & exhaust valve 736453M1 Key, intake & exhaust valve (pair) Connecting Rod Bearing Kits 747128M1 Thrust washer, upper. 2 used per engine. MF175, MF180, engine s/n 4812575 and up, All MF265, 31C, 6500 forklift. (lower washer tab off-center) 736878M91 1 kit used per engine. Rod bearing kit, standard 747129M1 Thrust washer, lower, tabbed. 2 used per engine. MF175, MF180, engine s/n 4812575 and up, All MF265, 31C, 6500 forklift. (lower washer tab off-center) 736879M91 Rod bearing kit,.010" 736880M91 Rod bearing kit,.020" MF-1-58

1 ENGINES Replacement parts to fit Tractor: MF1100 A6-354 Non-Turbo 354 CID 6 Cylinder Perkins Diesel Standard Bore 3.875" Engine Serial Number: Prior to 354UA3515 Piston pin 1-3/8" dia. Head gasket replaces MF/Perkins 36812544 and 36812522 Valve cover uses 6 bolts 2 Piece rope-type rear seal BEKP2316A-LCB EOK2316A-LCB TRU-POWER Engine Kits Engine bearings and thrust washers must be ordered separately. Basic engine kit. Contains sleeves, pistons, rings, pins, pin bushings, and overhaul gasket set with crankshaft seals. Engine overhaul kit. Contains sleeves, pistons, rings, pins, pin bushings, overhaul gasket set with crankshaft seals, valves, springs, guides, and keys. 736507M3 836583M91 733767M1 Cylinder Parts Cylinder liner. Ring set, for 1 piston. Can replace 738404M91 & 745769M91. 3 @ 3/32", 2 @ 1/4" Bushing, piston pin (6 used per engine) BIFP2316A Basic in-frame kit. Contains sleeves, pistons, rings, pins, valve grind set, and oil pan gasket kit. Gaskets Sleeve & Piston Kit PK316 Complete for 1 engine 1-3/8" piston pin diameter Sleeve and piston kit. Contains sleeves, pistons, pins, retainers, top chrome and bottom oil control ring set. For 3-7/8" standard bore. HS8279 CS5020 3638772M1 Head gasket replaces MF/Perkins #36812544 and #36812522. Valve covers use 6 bolts. Crankshaft seals are included in engine kits. Bottom gasket set includes the 2 piece rope-type rear seal. Top gasket set. Can replace Perkins 68279. Bottom gasket set. Replaces Perkins U5LB0020. Oil pan gasket. Crankshaft Seals 1447690M1 Seal, front, lip-type. 735942M1 Seal, rear, rope-type, 2 required (prior to s/n 248UA123424L) MF-1-59

1 ENGINES Tractor: MF1100 A6-354 Non-Turbo 354 CID 6 Cylinder Perkins Diesel Standard Bore 3.875" Engine Serial Number: Prior to 354UA3515 Piston pin 1-3/8" dia. Head gasket replaces MF/Perkins 36812544 and 36812522 Valve cover uses 6 bolts 2 Piece rope-type rear seal Valve Parts Main Bearing Kits VOKP354 739027M1 747552M1 736297M1 748420M1 735525M91 735521M1 Valve overhaul kit. Contains intake and exhaust valves, springs, keys, and guides. Valve, intake Valve, exhaust, stellite. Replaces 741257M1. Guide, intake Guide, exhaust Spring, inner, intake & exhaust valve Spring, outer, intake & exhaust valve 744001M1 744210M1 744211M91 1 kit used per engine (Thrust washers not included) Main bearing kit, standard Main bearing kit,.010" Main bearing kit,.020" Thrust Washers Upper thrust washer. 2 used prior to engine s/n 8504189. 736453M1 Key, intake & exhaust valve (pair) Connecting Rod Bearing Kits Lower thrust washer. 2 used prior to engine s/n 8504189. Tab on-center. 747128M1 Upper thrust washer. 2 used engine s/n 8504189 & up. 1 kit used per engine. 747129M1 Lower thrust washer, tab off-center. 2 used engine s/n 8504189 & up. 736934M91 Rod bearing kit, standard 736935M91 Rod bearing kit,.010" 736936M91 Rod bearing kit,.020" MF-1-60

1 ENGINES Replacement parts to fit Tractor: MF1100 A6-354 Non-Turbo 354 CID 6 Cylinder Perkins Diesel Standard Bore 3.875" Engine Serial Number: 354UA3515-354UA10361 Piston pin 1-3/8" dia. Head gasket replaces MF/Perkins 36812544 and 36812522 Valve cover uses 14 bolts 2 Piece rope-type rear seal BEKP2316B-LCB EOK2316B-LCB TRU-POWER Engine Kits Engine bearings and thrust washers must be ordered separately. Basic engine kit. Contains sleeves, pistons, rings, pins, pin bushings, and overhaul gasket set with crankshaft seals. Engine overhaul kit. Contains sleeves, pistons, rings, pins, pin bushings, overhaul gasket set with crankshaft seals, valves, springs, guides, and keys. 736507M3 836583M91 733767M1 Cylinder Parts Cylinder liner. Ring set, for 1 piston. Can replace 738404M91 & 745769M91. 3 @ 3/32", 2 @ 1/4" Bushing, piston pin (6 used per engine) BIFP2316B Basic in-frame kit. Contains sleeves, pistons, rings, pins, valve grind set, and oil pan gasket kit. Gaskets Sleeve & Piston Kit PK316 Complete for 1 engine 1-3/8" piston pin diameter Sleeve and piston kit. Contains sleeves, pistons, pins, retainers, top chrome and bottom oil control ring set. For 3-7/8" standard bore. HS8280 CS5020 3638772M1 Head gasket replaces MF/Perkins #36812544 and #36812522. Valve covers use 14 bolts. Crankshaft seals are included in engine kits. Bottom gasket set includes the 2 piece rope type rear seal. Top gasket set. Can replace Perkins 68280. Bottom gasket set. Replaces Perkins U5LB0020. Oil pan gasket. Crankshaft Seals 1447690M1 Seal, front, lip-type. 735942M1 Seal, rear, rope-type, 2 required (prior to s/n 248UA123424L) MF-1-61

1 ENGINES Tractor: MF1100 A6-354 Non-Turbo 354 CID 6 Cylinder Perkins Diesel Standard Bore 3.875" Engine Serial Number: 354UA3515-354UA10361 Piston pin 1-3/8" dia. Head gasket replaces MF/Perkins 36812544 and 36812522 Valve cover uses 14 bolts 2 Piece rope-type rear seal Valve Parts Main Bearing Kits VOKP354 739027M1 747552M1 736297M1 748420M1 735525M91 735521M1 Valve overhaul kit. Contains intake and exhaust valves, springs, keys, and guides. Valve, intake Valve, exhaust, stellite. Replaces 741257M1. Guide, intake Guide, exhaust Spring, inner, intake & exhaust valve Spring, outer, intake & exhaust valve 744001M1 744210M1 744211M91 1 kit used per engine (Thrust washers not included) Main bearing kit, standard Main bearing kit,.010" Main bearing kit,.020" Thrust Washers Upper thrust washer. 2 used prior to engine s/n 8504189. 736453M1 Key, intake & exhaust valve (pair) Connecting Rod Bearing Kits Lower thrust washer. 2 used prior to engine s/n 8504189. Tab on-center. 747128M1 Upper thrust washer. 2 used engine s/n 8504189 & up. 1 kit used per engine. 747129M1 Lower thrust washer, tab off-center. 2 used engine s/n 8504189 & up. 736934M91 Rod bearing kit, standard 736935M91 Rod bearing kit,.010" 736936M91 Rod bearing kit,.020" MF-1-62

1 ENGINES Replacement parts to fit Tractor: MF1100 A6-354 Non-Turbo 354 CID 6 Cylinder Perkins Diesel Standard Bore 3.875" Engine Serial Number: 354UA10362 and up Piston pin 1-3/8" dia. Head gasket replaces MF/Perkins 36812547 and 36812535 Valve cover uses 14 bolts 2 Piece rope-type rear seal BEKP3316-LCB EOK3316-LCB TRU-POWER Engine Kits Engine bearings and thrust washers must be ordered separately. Basic engine kit. Contains sleeves, pistons, rings, pins, pin bushings, and overhaul gasket set with crankshaft seals. Engine overhaul kit. Contains sleeves, pistons, rings, pins, pin bushings, overhaul gasket set with crankshaft seals, valves, springs, guides, and keys. 736507M3 836583M91 733767M1 Cylinder Parts Cylinder liner. Ring set, for 1 piston. Can replace 738404M91 & 745769M91. 3 @ 3/32", 2 @ 1/4" Bushing, piston pin (6 used per engine) BIFP3316 Basic in-frame kit. Contains sleeves, pistons, rings, pins, valve grind set, and oil pan gasket set. Gaskets Sleeve & Piston Kit Complete for 1 engine 1-3/8" piston pin diameter HS2605 Head gasket replaces MF/Perkins #36812547 and #36812535. Valve covers use 14 bolts. Crankshaft seals are included in engine kits. Bottom gasket set includes the 2 piece rope type rear seal. Top gasket set. Can replace Perkins 69005/U5LT0026. PK316 Sleeve and piston kit. Contains sleeves, pistons, pins, retainers, top chrome and bottom oil control ring set. For 3-7/8" standard bore. CS5020 3638772M1 Bottom gasket set. Replaces Perkins U5LB0020. Oil pan gasket. Crankshaft Seals 1447690M1 Seal, front, lip-type. 735942M1 Seal, rear, rope-type, 2 required (prior to s/n 248UA123424L) MF-1-63

1 ENGINES Tractor: MF1100 A6-354 Non-Turbo 354 CID 6 Cylinder Perkins Diesel Standard Bore 3.875" Engine Serial Number: 354UA10362 and up Piston pin 1-3/8" dia. Head gasket replaces MF/Perkins 36812547 and 36812535 Valve cover uses 14 bolts 2 Piece rope-type rear seal Valve Parts Main Bearing Kits VOKP354 739027M1 747552M1 736297M1 748420M1 735525M91 735521M1 Valve overhaul kit. Contains intake and exhaust valves, springs, keys, and guides. Valve, intake Valve, exhaust, stellite. Replaces 741257M1. Guide, intake Guide, exhaust Spring, inner, intake & exhaust valve Spring, outer, intake & exhaust valve 744001M1 744210M1 744211M91 1 kit used per engine (Thrust washers not included) Main bearing kit, standard Main bearing kit,.010" Main bearing kit,.020" Thrust Washers Upper thrust washer. 2 used prior to engine s/n 8504189. 736453M1 Key, intake & exhaust valve (pair) Connecting Rod Bearing Kits Lower thrust washer. 2 used prior to engine s/n 8504189. Tab on-center. 747128M1 Upper thrust washer. 2 used engine s/n 8504189 & up. 1 kit used per engine. 747129M1 Lower thrust washer, tab off-center. 2 used engine s/n 8504189 & up. 736934M91 Rod bearing kit, standard 736935M91 Rod bearing kit,.010" 736936M91 Rod bearing kit,.020" MF-1-64

1 ENGINES Replacement parts to fit Tractor: MF1130 AT6-354 Turbo 354 CID 6 Cylinder Perkins Turbocharged Diesel Standard Bore 3.875" Engine Serial Number: Engine s/n prior to 354UA3356T Piston pin 1-1/2" dia. Head gasket replaces MF/Perkins 36812548 2 Piece rope-type rear seal BEKP183A-LCB TRU-POWER Engine Kits Engine bearings and thrust washers must be ordered separately. Basic engine kit. Contains sleeves, pistons, rings, pins, pin bushings, and overhaul gasket set with crankshaft seals. 736507M3 738368M91 Cylinder Parts Cylinder liner. Piston w/pin. EOK183A-LCB Engine overhaul kit. Contains sleeves, pistons, rings, pins, pin bushings, overhaul gasket set with crankshaft seals, valves, springs, guides, and keys. 837422M91 Ring set, for 1 piston. 1 @ 1/8", 2 @ 3/32", 1 @ 1/4" BIFP183A Basic in-frame kit. Contains sleeves, pistons, rings, pins, valve grind set, and oil pan gasket kit. 735490M1 Bushing, piston pin (6 used per engine) Sleeve & Piston Kit Gaskets Complete for 1 engine Head Gasket replaces MF/Perkins #36812548. Crankshaft seals are included in engine kits. Bottom gasket set includes the 2 piece rope type rear seal. PK83 1-1/2" piston pin diameter 1 used per engine Sleeve and piston kit. Contains sleeves, pistons and rings, pins and retainers, complete for 6 cylinders. HS8291 CS5020 3638772M1 Top gasket set. Can replace Perkins 68291. Bottom gasket set. Replaces Perkins U5LB0020. Oil pan gasket. Crankshaft Seals 1447690M1 Seal, front, lip-type. 735942M1 Seal, rear, rope-type, 2 required (prior to s/n 248UA123424L) MF-1-65

1 ENGINES Tractor: MF1130 AT6-354 Turbo 354 CID 6 Cylinder Perkins Turbocharged Diesel Standard Bore 3.875" Engine Serial Number: Engine s/n prior to 354UA3356T Piston pin 1-1/2" dia. Head gasket replaces MF/Perkins 36812548 2 Piece rope-type rear seal Valve Parts Main Bearing Kits 1 kit used per engine (Thrust washers not included) 744001M1 Main bearing kit, standard VOKP354 739027M1 747552M1 736297M1 735525M91 Valve overhaul kit. Contains intake and exhaust valves, springs, keys, and guides. Valve, intake Valve, exhaust, stellite. Replaces 741257M1. Guide, intake Spring, inner, intake & exhaust valve 744210M1 744211M91 747128M1 Main bearing kit,.010" Main bearing kit,.020" Thrust Washers Upper thrust washer. 2 used engine s/n 8504189 & up. 735521M1 Spring, outer, intake & exhaust valve 748420M1 736453M1 Guide, exhaust Key, intake & exhaust valve (pair) Connecting Rod Bearing Kits 747129M1 Lower thrust washer, tab off-center. 2 used engine s/n 8504189 & up. 1 kit used per engine. 742561M91 Rod bearing kit, standard 742630M91 Rod bearing kit,.010" 742631M91 Rod bearing kit,.020" MF-1-66

1 ENGINES Replacement parts to fit Combine: 750 (to s/n 169615716), 760 (to s/n 1746009413) Tractor: MF1105, MF1130 (engine s/n 354UA3356T & up), MF1135 AT6-354 Turbo 354 CID 6 Cylinder Perkins Turbocharged Diesel Standard Bore 3.875" Piston pin 1-1/2" dia. BEKP183B-LCB TRU-POWER Engine Kits Engine bearings and thrust washers must be ordered separately. Basic engine kit. Contains sleeves, pistons, rings, pins, pin bushings, and overhaul gasket set with crankshaft seals. 736507M3 738368M91 Cylinder Parts Cylinder liner. Piston w/pin. EOK183B-LCB Engine overhaul kit. Contains sleeves, pistons, rings, pins, pin bushings, overhaul gasket set with crankshaft seals, valves, springs, guides, and keys. 837422M91 Ring set, for 1 piston. 1 @ 1/8", 2 @ 3/32", 1 @ 1/4" BIFP183B Basic in-frame kit. Contains sleeves, pistons, rings, pins, valve grind set, and oil pan gasket kit. 735490M1 Bushing, piston pin (6 used per engine) Sleeve & Piston Kit Gaskets Complete for 1 engine HS2605 Top gasket set. Can replace Perkins 69005/U5LT0026. PK83 1-1/2" piston pin diameter 1 used per engine Sleeve and piston kit. Contains sleeves, pistons and rings, pins and retainers, complete for 6 cylinders. CS5024 3638772M1 Bottom gasket set. Can replace Perkins U5LB0024. Oil pan gasket. MF-1-67

1 ENGINES Combine: 750 (to s/n 169615716), 760 (to s/n 1746009413) Tractor: MF1105, MF1130 (engine s/n 354UA3356T & up), MF1135 AT6-354 Turbo 354 CID 6 Cylinder Perkins Turbocharged Diesel Standard Bore 3.875" Piston pin 1-1/2" dia. Crankshaft Seals Connecting Rod Bearing Kits 1447690M1 Seal, front, lip-type. 735942M1 Seal, rear, rope-type, 2 required (prior to s/n 248UA123424L) 742561M91 1 kit used per engine. Rod bearing kit, standard 742630M91 Rod bearing kit,.010" 1447049M91 Seal, rear, lip-type (s/n 248UA123424L & up). For replacement blocks (2 required) 742631M91 Rod bearing kit,.020" Main Bearing Kits Valve Parts 1 kit used per engine (Thrust washers not included) 744001M1 Main bearing kit, standard 744210M1 Main bearing kit,.010" 744211M91 Main bearing kit,.020" VOKP354 739027M1 Valve overhaul kit. Contains intake and exhaust valves, springs, keys, and guides. Valve, intake 747128M1 Thrust Washers Upper thrust washer. 2 used engine s/n 8504189 & up. 747552M1 Valve, exhaust, stellite. Replaces 741257M1. 736297M1 748420M1 735525M91 Guide, intake Guide, exhaust Spring, inner, intake & exhaust valve 747129M1 Lower thrust washer, tab off-center. 2 used engine s/n 8504189 & up. 735521M1 Spring, outer, intake & exhaust valve 736453M1 Key, intake & exhaust valve (pair) MF-1-68

1 ENGINES Replacement parts to fit 354 CID 6 Cylinder Perkins Diesel Standard Bore 3.875" A6-354.4 Non-Turbo Perkins Diesel AT6-354.4 Turbo Perkins Diesel Connecting Rod Bearing Kits Thrust Washers 3637024M91 1 kit used per engine. Rod bearing kit, standard. For AT6-354.4 only Main Bearing Kits 747128M1 747129M1 Thrust washer, upper. 2 used per engine. MF175, MF180, engine s/n 4812575 and up, All MF265, 31C, 6500 forklift. (lower washer tab off-center) Thrust washer, lower, tabbed. 2 used per engine. MF175, MF180, engine s/n 4812575 and up, All MF265, 31C, 6500 forklift. (lower washer tab off-center) 1 kit used per engine (Thrust washers not included) 744921M91 Main bearing kit, standard MF-1-69

1 ENGINES Combine: Super 92 A6-305 Regular Injection 305 CID 6 Cylinder Perkins Diesel Standard Bore 3.6" Injectors Vertical in Head Cylinder Parts Valve Parts 732638M-CST Sleeve, CAST, for replacing original CHROME sleeve. Flange thickness.040". 739043M1 Sleeve, CAST, replacing original CAST sleeve. Flange thickness.150". Replaces 734175M1. 734460M91 Piston with pin, flat head. 731151M1 Valve, intake 731152M1 Valve, exhaust PRS334DC 836325M91 Ring set for 3 pistons only, use with CHROME sleeves, can replace 3-842521M92. 2 @ 3/32", 1 @ 1/8", 2 @ 1/4". Ring set, for 1 piston, used with CAST sleeves only. 2 @ 3/32", 1 @ 1/8", and 2 @ 1/4" 731153M1 731154M1 731155M1 Spring, inner, intake & exhaust valve Spring, outer, intake & exhaust valve Key, intake & exhaust valve (12 used per engine) Thrust Washers 740407M1 735866M1 Bushing, piston pin (6 used per engine) Crankshaft Seals Seal, rear, rope-type. For original production blocks (2 required) 735112M1 735113M1 Thrust washer, upper. 2 used per engine. Thrust washer, lower, tabbed. 2 used per engine. MF-1-70

1 ENGINES Replacement parts to fit Crankshaft Kits Timing Gears (Standard) 3638309M91 Crankshaft kit, new, with standard rod bearings, main bearings, & thrust washers. For Perkins AG3-152 gas, A3-152 & AD3-152 diesels. Uses 2 piece rope-type rear seal. 1/2" wide flywheel flange. 1750284M1 Crankshaft gear, 24 teeth. For Continental gas engine in tractors: TE20, TO20, TO30. 3641825M91 3638473M91 Crankshaft kit, new, with standard size rod & main bearings, & thrust washers. For Perkins AG3-152 gas & AD3-152 diesel engines using 1 piece lip-type rear seal, keyed nose, 1-1/2" wide flywheel flange. Replaces U5BG0027, 742827M91, 3637399M91, 3637410M91. Crankshaft kit for A4-203 & AD4-203 Perkins Diesels using 2 piece rope-type rear seal. Shaft not splined on gear end. 1750054M1 Crankshaft gear, 24 teeth. For Continental gas engine in tractors: TO35, MF35, MF50, MH50, MF135, MF150. Z129CK Crankshaft kit with standard size rod & main bearings. For Z129 Continental gas engine in tractors: TO30 with thrust on front main. Z134CK Crankshaft kit with standard size rod & main bearings. For Z134 Continental gas engine in tractors: TO30 late with thrust on center main, TO35, MF35, MF135; industrial: 202. 1750237M1 Camshaft gear, 48 teeth. For Continental gas engine in tractors: TE20, TO20, TO30, TO35, F40, MH50, MF50, MF135, MF150; industrials: 202, 204, 2135. Camshafts 836543M91 Camshaft, for Continental gas engines Z120, Z129, Z134. 9 tooth, 1.125" gear. Tractors: TE20, TO20, TO30, TO35, MF35, F40, MH50, MF50, MF135 Special; industrials: 202, 204, 2135. Replaces 1750074M1, 1750293M1. 1027656M1 Camshaft with nut, 10 tooth, 1.234" gear. For Continental Z145 gas engine in tractors: MF135, MF150, MF230, MF235, MF245; industrials: 20C, 30B; forklifts: 2500, 4500. MF-1-71

1 ENGINES Cylinder Heads Oil Pump Repair Kits 3638321M91 Cylinder head assembly, for Perkins A3-152 regular injection engine (injectors vertical in cylinder head). Head assembly includes valves & valve parts. Tractors: MF35, MF50; industrials: 35 utility, 203, 205. Replaces ZZ080058, 743272M91. OPK60A Oil pump repair kit. For Continental engine in tractors: TE20, TO20, TO30, TO35, MF35, MF135, MF50, MF150. Replaces 835643M91. Drive gear is 2-15/16" O.D. 3637389M91 Cylinder head assembly, for Perkins AD3-152 direct injection engines (injectors at angle in cylinder head). Includes valves & valve parts. For tractors: MF135, MF150, MF230, MF235, MF245; industrials: 20, 20C 30B, 30D, 40, 203, 205, 2135, 2200 treever; forklifts: 2200, 2500, 4500; crawlers: 200, 200B, 200C, 2244. Replaces cylinder heads 737704M91, 740595M91, 743201M91, these heads have valves with a 45 degree face angle & are no longer supplied by OEM. 3637389M91 is the same as supplied by the OEM & has valves with a 35 degree face angle. Replaces ZZ080082, ZZ080025, 747574M91. OPK65A TW1314S Oil pump repair kit. For Continental engine in tractors: MF65, MF165, MF175, MF180. Drive gear is 3-1/8" O.D. Thrust Washers Thrust washer set. Contains DI733713M1 (upper) and DI733714M1 (lower). Tractors: MF175, MF180 (prior to engine s/n 4812575). Oil Pumps For Perkins Engines 3638632M91 Oil pump assembly. Tractors: MF35, MF50, MF135, MF230, MF235, MF245, others using A3-152 & AD3-152 engines, gas and diesel. 3638633M91 Oil pump assembly. Tractors: MF65, MF165, MF255; industrials: 30, 40B, 50, 302, 304, 3165; combine: 300 S.P.; using A4-203 & AD4-203, gas & diesel. Replaces 41314164, 736617M91. MF-1-72

2 ENGINE SYSTEMS Replacement parts to fit Carburetors & Carburetor Repair Kits For tractor models using Continental gas engine. Application Tractor: TE20, TO20, TO30 Carburetor 181644M91 Industrial Tractor: 202, 204, 533969M91 2135 Tractor: TO35, F40, MH50, MF50, MF135, MF150 Tractor: MF65 184301M91 Forklift: 2500 194065M92 Industrial Tractor: 2135 Tractor: MF135, MF150 Industrial Tractor: 3165 194603M92 Tractor: MF165 Carb Manufacture Carb Manufacture Tractor Manufacture Numbers Carb Numbers Marvel-Schebler TS458, TS361A, n/a Marvel-Schebler n/a, TS605, TS683, TS882 Zenith Zenith Zenith 0-14992 0-12566 0-14992 181644M91, 181643M91, C549V 517903M91 533969M91, 181532M91, C549AV 183576M91, 194065M91 184301m91 (TS695) 194605M91 (TS882) 194603M91 (TS884) Complete Basic Repair Kit Repair Kit BK48V BK49V Gasket Kit CGK32 CGK32 K2127 K2112 K2127 Application Complete Carb Manufacture Carb Manufacture Repair Kit Numbers Tractor: TE20, TO20 C548V Marvel-Schebler TS361A, n/a Tractor: TO20, TO30 C549V Marvel-Schebler TS458 Industrial Tractor: 202, 204, C549AV Marvel-Schebler TS605, TS683, 2135 TS882, N/A Tractor: TO35, F40, MH50, MF50, MF135, MF150 Industrial Tractor: 202, 204, Carter UT2223S, UT2418S 2135 Tractor: TO35, F40, MH44, MH44K, MH50, MF50, MH444 Zenith 62AJ9/10444, 62AJ/10279A Tractor: MF85, MF88 Marvel-Schebler TS644, TS786-1 Industrial Tractor: 3165 C549BV Marvel-Schebler TS695, TS884 Tractor: MF65, MF165 Tractor: MF175 Marvel-Schebler TS893, TS916 Tractor Manufacture Carb Numbers 181643M91, 517903M91 181644M91 181532M91, 183576M91, 194065M91, 533969M91 181578M91, 182748M91 761544M91, 6809A Basic Repair Gasket Kit Kit BK48V CGK32 BK48V CGK32 BK49V CGK32 BK201V BK87V 184845M91, 191960M91 BK317 184301M91, 194603M92 BK49BV 506003M91, 512627M91 BK49BV CGK26 CGK34 CGK34 MF-2-73

2 ENGINE SYSTEMS K2112 K2136 Carburetor Tune-up Kit Carburetor tune-up kit contains: valve & seat, idle adjusting needle, and necessary gaskets, seals, bushings, plugs, washers, float pin, and instructions for carburetor repair. Used In A Wide Range Of Other OEM Equipment Tune-up kit for Zenith carburetors used in various Massey Ferguson equipment. Services the following carburetor models: 12098 12108 12115 12122 12123 12225 12253 12262 12285 12319 12325 12331 12340 12341 12342 12384 12385 12386 12389 12449 12492 12493 12522 12544 12566 12567 12512 12654 12658 12690 12699 12775 12911 13007 13028 13047 13053 13056 13105 13206 13210 13276 13292 13309 13324 13371 13379 13386 13397 13405 13422 13423 13468 13469 13471 13484 13541 13542 13549 13556 13565 13653 13694 13705 13713 13719 13720 13727 13733 13735 13769 13781 13794 13800 13803 13819 13822 13843 13873 13876 13877 13878 13879 13880 13895 14002 14017 14544 Tune-up kit for Zenith carburetors used in various Massey Ferguson equipment. Services the following carburetor models: 11535 11994 12032 12241 12420 12548 12675 12804 12805 12851 12885 12886 12912 12913 13025 13026 13038 13048 13108 13109 13115 13116 13118 13119 13157 13178 13226 13236 13316 13337 13338 13348 13383 13406 13419 13433 13434 13435 13465 13467 13538 13546 13572 13588 13597 13612 13624 13636 13677 13689 13762 13762 13795 13831 13844 13875 13881 13956 13993 K2127 Carburetor tune-up kit for Zenith carburetors used in various Massey Ferguson equipment. Services the following carburetor models: OS820 10329 10940 11011 11012 11222 11258 11535 11580 11588 11705 11741 11892 11900 11929 11994 11996 11999 12032 12060 12212 12214 12217 12232 12237 12241 12287 12301 12318 12351 12396 12418 12420 12425 12430 12457 12468 12473 12490 12498 12499 12501 12509 12523 12534 12551 12576 12592 12617 12625 12629 12648 12651 12656 12669 12680 12685 12701 12722 12727 12731 12758 12770 12771 12794 12795 12804 12805 12820 12822 12880 12885 12886 12912 12913 12920 12922 12950 12960 12962 12974 12975 12991 12992 12998 13016 13025 13026 13037 13039 13041 13044 13048 13059 13061 13066 13067 13069 13071 13106 13108 13109 13111 13112 13113 13114 13115 13116 13117 13119 13120 13121 13122 13123 13124 13125 13128 13129 13147 13150 13151 13152 13153 13154 13157 13160 13161 13163 13164 13165 13170 13178 13186 13198 13202 13212 13213 13226 13236 13294 13304 13316 13328 13337 13338 13348 13357 13358 13359 13373 13383 13384 13390 13406 13419 13433 13434 13435 13462 13465 13467 13488 13489 13534 13538 13545 13546 13560 13572 13588 13597 13604 13608 13609 13610 13612 13624 13636 13677 13689 13716 13752 13770 13771 13783 13823 13831 13844 13876 13881 13893 13919 13939 13956 13960 13961 13978 13980 13981 13985 14028 14991 14992 14995 14996 14998 14999 Throttle Body Repair Bushings Designed to bush worn throttle bodies. T818 Upper bushing, 1/4" shafts. OD.383", ID.247", L.501". T819 Lower bushing, 1/4" shafts. OD.323", ID.247", L.471". MF-2-74

2 ENGINE SYSTEMS Replacement parts to fit Carburetor Floats Fuel Strainers For Marvel-Schebler carburetors. 15480A 1508838M91 Float for Marvel-Schebler small bowl carburetors. Tractors: TO20, TO30, TO35, MF35, F40, MH50, MF135, MF150. Float for Marvel-Schebler large bowl carburetors. Tractors: MF65, MF150, MF165, MF175. Industrials: 3165 using carburetor models: TS695, TS884, TS893, TS947SL. Float Valve Assemblies 180141M91 For Continental Gas Or Standard Motors Diesel Engines Strainer assembly. Tractors: TO35, MF35, F40, MH50, MF50, MF65, MF85, MF88. Industrials: 35, 202 (prior to s/n 309328), 204 (prior to s/n 343891), 302 (prior to s/n 119700213), 304 (prior to s/n 119750210), 356 (prior to s/n 670001084). Parts for 180141M91: SFV1 Shut-off fuel valve. 180060M1 Gasket, bowl to body, 2" O.D. 1001514M1 Glass bowl. 2" O.D., 1.280" long 15479AV 14876AV Float valve needle & seat. For Marvel-Schebler carburetors. Tractors: 11 Pony, 16 Pacer, 20, 21, 22, 23, MH30, TE20, TO20, TO30, TO35, MF35, F40, MH50, MF50, MF135, MF150. Industrials: 202, 204, 2135, 2200, 2500. Float valve needle & seat. For Marvel-Schebler carburetors. Tractors: 33, 33K, 333, MF65, MF85, MF88, MF90, MF Super 90, MF165, MF175, MF180. Industrials: 302, 303, 304, 356. Carburetor Inlet, Elbow & Strainer 2N9166 505472M91 1026360M1 1037982M1 1026556M1 12084G Bail assembly. Strainer assembly. Tractors: MF135, MF150 (Continental gas only), MF165, MF175, MF180. Industrials: 20, 30, 50, 202 & 204 (late model), 302 (s/n 119701046 & up), 304 (s/n 119751024 & up), 356 (late model), 2135, 3165. Parts for 505472M91: Glass bowl. 2-1/8" O.D., 2.370" long. Screen, fuel strainer. Gasket, bowl to body, 2-1/8" O.D. Bail & screw assembly. 850042M1 Sediment bowl assembly. Includes horizontal inlet and outlet with 1/8" x 1/8" female pipe threads. Tractors: Massey Harris: Pony (to s/n PGA3116). Vintage Iron 1751212M91 Elbow & strainer assembly. Tractors: TE20, TO20, TO30, TO35, MF35, MF50. MF-2-75

2 ENGINE SYSTEMS Fuel Tank Valve Fuel Gauge For Instrument Panel 1851653M91 898540M91 Fuel shut-off valve. Tractors: MF50, MF65. Shovel Loader: 356. Fuel shut-off & strainer. Tractors: MF231, MF240 & MF250 (without reserve tank). Industrials: 20D (early models), 30E, 40E. Replaces 1453886M1. 1877717M92 520948M91 Gauge, fuel. For instrument panel. Tractors: MF231, MF240, MF250, MF253, MF270, MF282, MF283 (except Brazil), MF290, MF298, MF2775 (prior to s/n 9R0726), MF2805 (prior to s/n 9R0726). Industrials: 20D, 30E, 40E, 50E, 50F. Fuel Tank Cap Cap, fuel tank. All gas models. 898580M91 FTW494 1661794M92 1678517M2 Fuel shut-off & strainer. Tractors: MF270 (early models), MF290 (early models), MF298 (early models). Industrials: 50E, 50F. Forklifts: 6500H, 6800H. Replaces 890438M1. Fuel Tank Webbing Fuel tank webbing. (Sold 3 foot lengths). Black woven nylon type material,.042" thick. Tractors: Fits Allis Chalmers, Avery, Case, Cockshutt, Ford, IH/Farmall, John Deere, Massey Harris, Minneapolis Moline and Oliver models. Vintage Iron Fuel Tank Sending Units Sending unit, for fuel tank. Tractors: MF240, MF250, MF253. Industrials: 20D, 30E, 40E. Sending unit, for fuel tank. Tractors: MF270, MF282, MF283 (except Brazil), MF290, MF298. Industrials: 50E, 50F. Replaces 16996610M1 27556D 12648G 850493M1 761337M91 Auxiliary fuel cap, includes gasket. 1-¾" ID,.350" height. Tractors: Massey Harris: 20, 22, 30, 33, 44, 55, 81, 82, 101 Jr, 101 Sr, 102 Jr, 102 Sr, 333, 444. Vintage Iron Cap. Can be used for auxiliary gas tank cap, power steering reservoir cap, oil filler cap and engine oil cap. Tractors: Massey Harris: Pony (engine oil cap). Vintage Iron Fuel cap. Vented and includes cork gasket. 2-½" ID, ¼" high, 2-5/8" OD. Tractors: Massey Ferguson: TE20 (not threaded), TO20, TO30, TO35, MF35, MF40, MF50, MF65, MF85, MF88, Super 90, MF135, MF150, MF165, MF175, MF1080, MF1100, MF1130, MF1150, MF1500, MF1800. Massey Harris: 50, Pony, Pacer. Vintage Iron Fuel cap with gasket. Vented, 2-11/16" ID, 5/8" height. Top of cap reads "Buy Clean Fuel, Keep it Clean". Tractors: Massey Harris: Colt, Challenger, Mustang, 20, 22, 23, 30, 33, 44, 44-6, 44 Special, 81, 82, 101 Jr., 102 Jr, 101 Sr, 102 Sr. Vintage Iron MF-2-76

2 ENGINE SYSTEMS Replacement parts to fit 3637288M91 3637307M91 3637292M91 3637286M91 Fuel Lift Pumps Fuel pump for A3-152 & AD3-152 diesel engines, two-hole mounting. Tractors: MF35, MF50, MF135 (prior to s/n 152UA46497D), MF150 (prior to s/n 152UA46497D). Industrials: 203 & 205 (prior to s/n 152UA46497D), 2135 (prior to s/n 152UA46497D). Replaces: 35273, 2641406, 885363M91, & 890960M91. Fuel pump for AD3-152 diesel engine, two-hole mounting. Tractors: MF135 (s/n 152UA46497D & up), MF150 (s/n 152UA46497D & up), MF154-4, MF230 (prior to s/n U635849G), MF235, MF240 (prior to s/n U635849G), MF245 (prior to s/n U635849G). Industrials: 20, 20C (prior to s/n U635849G), 30B (prior to s/n U635849G), 40, 203 & 205 (s/n 152UA46497D & up), 2135 (s/n 152UA46497D & up). Replaces 2641311 & 886062M9. Fuel pump for AD3-152 diesel engine, four-hole mounting. Tractors: MF154-4S, MF230 (s/n U635849G & up), MF231, MF240 (s/n U635849G & up), MF245, MF250, MF253, MF254-4. Industrials: 20C (s/n U635849G & up), 20D, 30B (s/n U635849G & up), 30D, 30E, 40E. Replaces 2641808, 2641712, & 1447582M91. Fuel pump for AD4-203 & A4-318 diesel engines, two-hole mounting. Tractors: MF165 (s/n 29F4249 & up), MF255, MF285, MF298, MF698, MF1080, MF1085. Industrials: 30, 40B, 50, 50A, 302 & 304 (s/n 29F4249 & up), 3165 (s/n 29F4249 & up). Combine: 540. Replaces 26471328, 2641333, 2641336, 886100M91, 14466155M91, 1447693M91. 3637338M91 3637287M91 3637300M91 3637290M91 3637309M91 3637415M91 Fuel pump for AD4-203 diesel engine, two-hole mounting, glass bowl. Tractors: MF65, MF165 (prior to s/n 29F4249). Industrials: 302 & 304 (prior to s/n 29F4249), 3165 (prior to s/n 29F4249). Combines: 300. Replaces 32589, 2641345, 890955M91, 892630M91. Fuel pump for AD4-236 diesel engines, two-hole mounting. Tractors: MF175 (prior to s/n 236UA57083), MF180 (prior to s/n 236UA57265). Industrials: 31 (prior to s/n 236AU57265). Replaces 2641465, 2641478, 881303M91, 1447381M91. Fuel pump for A4-236 & A4-248 diesel engines, four-hole mounting. Tractors: MF175 (s/n 236UA57083 & up), MF180 (s/n 236UA57265 & up), MF184-4, MF255, MF265, MF270 (early models), MF274-4 (prior to s/n 221N00936), MF275, MF294-4 (prior to s/n 223000321), MF670, MF690. Industrials: 31 (s/n 236UA57083 & up), 50E. Replaces 2641711, 1447017M91. Fuel pump for AD4-236 & AD4-248 diesel engines, four-hole mounting. Tractors: MF270 (late model), MF274-4 (s/n 221N00936 & up), MF283, MF294-4 (s/n 223000321 & up), MF375, MF383, MF390, MF390T, MF398, MF3050, MF3060, MF3070. Industrials: 50D. Replaces 2641725, 2641728, 1447688M91. Fuel pump for A6-372 & AT6-354 diesel engines, two-hole mounting. Tractors: MF1105, MF1135. Combines: 750 (prior to s/n 169615716), 760 (prior to s/n 1746009413). Replaces 2641372, 892632M91. Fuel pump, for A4-300, A6-354, AT6-354 diesel engines, two-hole mounting. Tractors: MF super 90 (s/n 6907623 & up), MF1100, MF1130. Combine: 410. Replaces: 2641A061, 2641344, 892629M91. MF-2-77

2 ENGINE SYSTEMS 4222105M91 3637289M91 Fuel pump assembly, Diesel engines, 4 hole mounting. Tractors: MF175, MF180, MF265, MF362, MF396, MF399 (w/a6-354.4 engine, 1006.6 engine), MF699, MF2640, MF2675, MF2705, MF2745, MF3090, MF3095, MF3120, MF3125, MF3140, MF3505, MF3525, MF3545, MF3630, MF3645, MF3650, MF3655, MF3660, MF4245, MF4255, MF4260, MF4263, MF4265, MF4270, MF4360, MF4370, MF4800, MF4900, MF6100, MF6120, MF6150, MF6170, MF6180, MF6190, MF6270, MF6280, MF6290, MF8100, MF8210, MF8220. Combines: 550, 750, 760, 850, 855, 860, 865. Industrials: 6500 Forklift. Stationary engines: A4-236, A6-354.4, T6-354.4, 1006.6, 1006.6T, 1006.6TW. Fuel pump for AV8-510 & AV8-540 diesel engines, two-hole mounting. Tractors: MF1150, MF1155. Combines: 760 (s/n 1746009413 & up), 850 (prior to s/n 1746019115). Replaces: 2641473, 2641479, 2641506, 2641507, 738109M91, 1446184M91, 1446681M91, 1447566M91. 1446876M1 1447169M1 1447605M1 881306M91 Fuel Injector Pumps To assure proper fit the Mfg #s number on the old part must match the Mfg #s on the new replacement part Fuel injection pump (NEW). AD4.236 engine. Tractors: MF175, MF180, MF255, MF265, MF270, MF275, MF6070. Industrials: MF6500, MF31, MF50C, MF50D. Replaces 1447267M1. Reference number CAV3241F360. Fuel injection pump (NEW). AD3.152 engine. Tractors: MF135, MF135UK, MF150, MF235, MF245. Industrials: MF20, MF40, MF200, MF200B, MF2135, MF2200, MF2500, MF4500. Replaces 1446012M1, Reference numbers CAV3230F240, CAV3230F180, CAV3230F190, CAV3230F350. Fuel injection pump (NEW). Tractors: MF285, MF298, MF698, MF1080, MF1085. Replaces 144182M1, 1446202M1, 1446846M1, 1447178M1, 144605M1. Reference numbers CAV3342F410, CAV3342F411, CAV3249F240, CAV3343F010. Fuel injection pump (NEW). A3.152 non-advance engines. Tractors: MF35, MF50, MH50. Industrials: MF203, MF205. Reference number CAV3230F030. 886068M1 Fuel injection pump (NEW). A6.354 engine. Tractors: MF1100, MF1105. Reference numbers CAV3263F670, CAV3362F080, CAV3262F948. 3637314M1 Fuel injection pump (NEW). AT4.236 engine. Tractors: MF390T, MF393, MF398, MF3065, MF3070. Reference numbers CAV3348F230, CAV3348F280. 3240F938 Fuel Injection Pump. Tractors: MF165, MF255. Industrials: 40, 50. Replaces 883517M91. Reference number CAV3240F938. MF-2-78

2 ENGINE SYSTEMS Fuel Injector Nozzle Tips Replacement parts to fit When ordering nozzles for rebuilding, check C.A.V. or Bosch part number stamped on tip body for positive identification. Application Nozzle Tractor: MF35, MF50; Utility: 35, Tractor Shovel: 356; 1851744M1 A3-152, A4-203 engines. Tractors: MF50, MF65 Industrial Tractors: 35, 203, 205, 356 1446701M91 Tractors: MF150, MF165 Combines: 300 Industrial Tractors: 1853019M91 20, 30, 40B, 50, 203, 205, 302, 304, 356, 2135, 3165 Tractors: MF175, MF180, MF265 Industrial Tractors: MF175, 1853029M91 MF180, MF265 Tractors: MF1100 MF1105, MF1135, MF1130 Combines: 883258M91 750 1447005M91 1446697M94 1446699M91 1447228M91 1446788M91 734596M91 736179M91 Fuel Injectors Fuel injector. Tractors: MF255. Replaces OEM 1446697E91 and 1446697R91. Fuel injector. Tractors: MF175 UK, MF178 UK, MF194-4F, MF265S, MF275, MF282, MF285S, MF294-4. Industrials: 50E, 50H. Replaces OEM 1446699E91 and 1446699R91. Fuel injector. Tractors: MF165 UK, MF174-4S, MF175, MF178, MF180, MF184-4, MF265, MF265S, MF270, MF274-4, MF275 UK, MF285S, MF294-4, MF365, MF374S, MF374V, MF384S, MF670. Industrials: 31, 50C, 50D, 50E, 50F, 50H. Replaces OEM 1446761M91 and 1447228E91. Fuel injector. Tractors: MF20, MF30, MF65, MF135, MF135 UK, MF150, MF165, MF230, MF235, MF255, MF300. Industrials: 40, 40B, 50, 50A, 302, 304, 2135, 3165. Replaces OEM 1446702M1, 733272M91, 736800M91. Fuel injector. Tractors: MF20, MF135, MF135 UK, MF150, MF165, MF165 UK, MF200, MF300. Industrials: 40, 302, 304, 2135, 2200, 3165. Fuel injector. Tractors: MF80, MF510, MF1100, MF1130. Replaces OEM 736179E91. 1447218M91 1447401M91 1004498M1 1024386M1 1039071M1 Bosch No. N/A DLL 150S 316 N/A DLL 150S 324 DLL 150S 469 CAV No. BDLL 110S6133 BDLL 150S 6554 BDLL 150S 6372 BDLL 150S 6382 BDLL 150S 6472 Fuel injector. Tractors: MF1105, MF1135. Fuel injector. Tractors: MF283, MF283 UK, MF290, MF290 UK, MF383, MF390, MF394S, MF690, MF3050, MF3060. Loader Backhoe: 50H. Replaces OEM 1447218E91, 1447218R91 and 2645664. Fuel injector. Tractors: MF230, MF231, MF240, MF250, MF255, MF275. Industrials: 20D, 20F, 30E, 40B. Replaces OEM 1447401E91 and 1447401R91. Transparent Fuel Pump & Filter Bowls Glass fuel bowl, for diesel fuel lift pump. 2-1/16 dia. Tractors: MF35, MF50, MF65, MF Super 90, MF135, MF150, MF165, MF1100, MF1130. Industrials: 203, 205, 2135, 3165. Combines: 300, 410. Glass bowl, used with filter elements 1077260M91, 1851890M1, CAV7111/296. Glass bowl, used with filter elements 3405419M1, 1896287M91, CAV7111/429. MF-2-79

2 ENGINE SYSTEMS Pre-Cleaner Bowls Diesel Fuel Filters 1508881M1 1018554M1 1508880M1 3119337 Bowl, pre-cleaner. Tractors: MF245, MF275. Can replace Donaldson #PO2-227. Vintage Iron A) Bowl O.D. at top 7-1/4" B) Cone I.D. at top 3-1/2" C) Bowl side height 3" D) Overall height 4-1/8" Bowl, pre-cleaner. Tractors: MF1100, MF1105, MF1130, MF1135, MF1150, MF1155. Can replace Donaldson bowl # PO1-6330. Vintage Iron A) Bowl O.D. at top 10-1/2" B) Cone I.D. at top 5-9/16" C) Bowl side height 3" D) Overall height 4" Clear plastic pre-cleaner bowl. 5.5" top OD, 5" bottom OD. Tractors: MF30, MF31, MF35, MF65, MF85, MF88, MF97 (to s/n 25202767), MF98, MF150, MF165, MF175, MF180, MF200, MF375, MF383, MF390, MF393, MF398, MF399, MF699, MF1080, MF1085, MF3050, MF3060, MF3070, MF3080, MF3090, MF3120, MF3165, Super 90. Vintage Iron Pre cleaner cover. Includes brass nut. 7" diameter. Tractors: MF35 (diesel), 65 (diesel), MF85, MF88, MF90, MF98, MF135, MF150, MF165, MF175, MF180, MF245, MF275, MF282, MF375, MF383, MF390, MF393, MF398, MF399, MF1080, MF1085, MF3050, MF3060, MF3070, MF3080, MF3090. Vintage Iron 1850450M2 3405419M1 CAV7111/796 CAV7111/296 3238343M1 Fuel filter element, cartridge type. Used in filter assembly 882272M91 (Purolator). Tractors: MF65 (primary & secondary), 35 Utility (primary). Fuel filter element, external body type. 4-3/8" high. Tractors: MF230, MF235, MF245, MF255, MF265, MF270, MF275, MF282, MF283UK, MF283 Brazil, MF290, MF360, MF375, MF383, MF390, MF390T, MF398, MF670, MF690, MF2745, MF2775, MF2805, MF3050, MF3060, MF3070, MF3505, MF3525, MF3545, MF3630, MF3680, MF3690. Industrials: 20C, 30B, 30D, 30H, 40B, 50C, 50D, 50E, 50F, 50H, 50H, 60H. Forklifts: 4500, 6500. Can replace Perkins 26560602, 1896287M91. Fuel Filter, Can type, 4-3/8" tall diesel fuel filter used with the cav fuel filter system. Tractors: MF145, MF200B, MF200C, MF200D, MF245, MF251E, MF255, MF261, MF265, MF270, MF275, MF275DT, MF275ST, MF282, MF283, MF290, MF292, MF294, MF294-4, MF355, MF365, MF375, MF383, MF390, MF390T, MF398, MF415, MF415N, MF435, MF560, MF575, MF590, MF670, MF675, MF690, MF698T, MF1100, MF1114, MF2620, MF2640, MF2645, MF2680, MF2685, MF2720, MG2725, MF2745, MF2775, MF2805, MF3330M, MF3340, MF3050, MF3060, MF3670, MF3680, MF3690, MF8140, MF8150, MF8160, MF8170, MF8180, MF8240, MF8245, MF8250, MF8260, MF8270, MF8280. Industrials: 20C, 30B, 3. Original C.A.V. fuel filter element, external body type. Can replace 1049939M91, 1077260M1, 1851890M1. Fuel filter, 2.717" tall. Tractors: MF1010, MF1020, MF1030. 1077260M91 Fuel filter element, external body type 2-3/4 high. All MF tractors & combines using filter assembly. 193229M91, 1447136M91, 1447363M91, & 1447072M91. Will work wherever CAV7111/296 filter is applicable. Replaces 835994M92 (Tri-Pak is replaced by single element) 1049939M91, 1851890M1. MF-2-80

2 ENGINE SYSTEMS Replacement parts to fit CAV7176/096 3638291M1 3780299M1 Original C.A.V. fuel filter element, external body type. Can replace 1049939M91, 1077260M1, 1851890M1, Perkins #26561117 & CAV7111/096, CAV7111/296 in all MF applications using filter assembly 193229M91, 1447136M91, 1447363M91 & 1447072M91. Spin-on fuel filter with drain. For diesel engines. Tractors: MF3120T, MF3140 (s/n U514769U & up), MF3660 (s/n U51477U & up). Replaces CAV7176/496A. Fuel water separator cartridge (PRIMARY). Tractors: MF396, MF5465, MF6235, MF6235HV, MF6245, MF6245HV, MF6255, MF6255HV, MF6260, MF6265, MF6270, MF6280, MF6290, MF6465, MF6475, MF6480, MF6497, MF6499, MF7465, MF7475, MF7480, MF8210, MF8220, MF8240, MF8240TRA, MF8250TRA, MF8260, MF8260TRA, MF8270, MF8270TRA, MF8280, MF8280TRA. Air Cleaner Elements 3901464M1 3901465M1 Air filter element, outer, radial seal. Tractors: 4225, 4225A (w/perkins 1004-40 engine); 4233, 4235 (w/perkins 1004-42 engine); 4345, 4355 (w/perkins 1004-4TW engine); 5425, 5435, 5435HV (w/perkins 1104C-44 engine); MF275, MF275DT, MF275ST (w/perkins P4000 (4.1L) engine); MF4243, MF4245, MF4253, MF4255 (w/perkins 1004.40TW); MF4325 (w/perkins 1004.4 engine); MF4335 (w/perkins 1004.42 engine); MF435, MF5285 (w/perkins engine); MF6235, MF6245, MF6255 (w/perkins 1004-40T engine). Air filter element, inner, radial seal. Tractors: 4225, 4225A (s/perkins 1004-40 engine); 4233, 4235 (w/perkins 1004-42 engine); 4345, 4355 (w/perkins 1004-4TW series engine); 5425, 5435 (w/perkins 1104C-44 engine); MF275, MF275DT, MF275ST (w/perkins P4000 (4.1L) engine); MF4243, MF4245, MF4253, MF4255 (w/perkins 1004.40TW engine); MF4325 (w/perkins 1004.4 engine); MF4335 (w/perkins 1004.43 engine); MF435, MF5285 (w/perkins engine); MF6235 (w/perkins 1004-40T engine); MF6245, MF6255 (w/perkins 1004-40T engine). 1032762M91 1029945M92 1026131M92 1028094M94 1094056M91 Air cleaner element, horizontal, single or outer dual, gas & diesel engines. Tractors: MF135. Industrials: 20, 2135. Air cleaner element, vertical, single or outer dual, gas & diesel engines. Tractor: MF135. Industrial: 2135. Air cleaner element, single or dual outer. Tractors: MF150, MF165, MF175, MF180. Industrials: 30, 50 (gas only), 50A. Replaces 1026191M91, 1805045M1. Air cleaner element, for single element filter. Tractors: MF1100, MF1130 (prior to s/n 9824396). Air cleaner element, outer, for dual element filter. Tractors: MF235 Orchard, MF245 Orchard, MF255, MF265. 3901475M1 3901476M1 Air filter, outer, radial seal. Tractors: 4260A, 4270A (w/perkins 1006 engine); 4270 (w/perkins engine); 4345, 4355 (w/perkins 1004-4TW engine); 5425 (w/perkins 1104C-44 engine); 5445, 5455 (w/perkins 1104C-44T engine); 6265 (w/perkins 1004-4TW engine); 6445, 6455 (w/perkins 1104C engine); MF4243, MF4245, MF4253, MF4255 (w/perkins 1004.40TW engine); MF4263, MF4325 (w/perkins 1004.4 engine); MF4335 (w/perkins 1004.42 engine); MF4360, MF4370 (w/perkins 1006.6 engine); MF5340, MF5355 (w/perkins engine); MF6235, MF6245, MF6255 (w/perkins 1004-40T engine); MF6260 (w/perkins 1006-60NA engine). Air filter element, inner, felt media radial seal. Tractors: 4270 (w/perkins engine); 4345, 4355 (w/perkins 1104-4TW engine); 5425 (w/perkins 1104C-44 engine); 5445, 5455 (w/perkins 1104C-44T engine); 6265 (w/perkins 1004-4TW engine); 6445, 6455 (w/perkins 1104C engine); MF4243, MF4245, MF4253, MF4255 (w/perkins 1004-40TW engine); MF4263, MF4325 (w/perkins 1004.4 engine); MF4335 (w/perkins 1004-42 engine); MF4360, MF4370 (w/perkins 1006.6 engine); MF5340, MF5355 (w/perkins engine); MF6235, MF 6245, MF6255 (w/perkins 1004-40T engine); MF6260 (w/perkins 1006-60NA engine). MF-2-81

2 ENGINE SYSTEMS OBAC422 Oil bath air cleaner filter element. Fits most oil bath air cleaners to replace mesh in the existing air cleaner. Tractors: Avery, Case, Cockshutt, Ford, IH/Farmall, John Deere, Massey Ferguson, Massey Harris, Oliver, Minneapolis Moline. Vintage Iron Engine Oil Filters 15790A Air cleaner clamp. Fits Donaldson air cleaner. Tractors: Massey Ferguson: All gas TE20, TO20, TO30, TO35, MF35, 202, 204. Massey Harris: 20, 81, 82, 101 Jr, 102 Jr. Vintage Iron Air Cleaner Oil Cup Cartridge Type 15791A 180062M1 1861746M1 763183M91 T7030 Air cleaner oil cup. 4-¾" OD at lip, 3" Height, 4.450" ID. Tractors: Massey Ferguson: TO20 gas, TO30 gas, TO35 gas, MF35 gas, 202 gas, 204 gas. Massey Harris: 20, 81, 82, 101 Jr, 102 Jr. Vintage Iron Air Cleaner Hose Hose, air cleaner tube to carburetor. Tractors: TE20, TO20, TO30, MF35, MH50, MF50, MF135, MF150 (except Perkins). 1.820" O.D., 1.500" I.D., 2.350" long. Hose, air cleaner to manifold. For dry type air cleaner. Tractors: MF240, MF250. Industrials: 20D, 30E. Air Cleaner Caps Air cleaner cap. Fits outside pipe. 2" ID, 5.25" body diameter. Tractors: Massey Harris: Colt, Mustang, 20, 21, 22, 22K, 30, 30K, 33, 44 Special, 81, 82, 101 Jr, 102 Jr. Vintage Iron Air cleaner cap with flat wire. Fits inside pipe. 4-1/8" body diameter, 1-7/8" OD. Tractors: Massey Harris: Colt, Mustang, 20, 21, 22K, 30, 30K, 33, 44 Special, 81, 82, 101 Jr, 102 Jr. Vintage Iron 830910M91 841244M91 1014219M92 835817M91 837595M91 835568M93 1447082M1 Tri-pac of oil filter elements, 3 cartridge type. Tractors: TE20, TO20. Oil filter element. Tractors: TE20, TO20. Tri-pac of oil filter elements, 3 cartridge type. For early gas engines. Tractors: 11 Pony, 16 Pacer, 20, 22, 23, 30, 33, 333; TO30, TO35, MF35, F40, MF50, MF65 (repl. orig. Fram C3 element), MF85, MF88, Super 90, MF135, MF150, MF165, 35, 65 (turf & utility). Industrials: 203, 205, 302, 304, 2135, 3165, 356 shovel. Oil filter element. Tractors: 11 Pony, 16 Pacer, 20, 22, 23, 30, 33, 333, TO30, TO35, MF35, F40, MF50, MF65 (replaces original Fram element), MF85, MF88, Super 90, MF135, MF150, MF165, 35, 65 (turf & utility). Industrials: 203, 205, 302, 304, 2135, 3165, 356 Shovel. Oil filter element, cartridge type. For diesel engines. Tractors: FE35, MF35, MF50, MF65, MF135, MF150, MF165, 35, 65 utility. Industrials: 203, 205, 302, 304, 2135, 3165 Utility. Replaces 1851766M1, 1852251M91, 1883258M91 Tri-pack of oil filter elements 3 cartridge type 837595M91. For diesel engines. Tractors: FE35, MF35, MF50, MF65, MF135, MF150, MF165, 35 Utility, 65 Utility. Industrials: 203, 205, 302, 304, 2135, 3165 Utility. Spin-On Type Oil filter spin-on element, 10-11/16" long. Tractors: MF135, MF150, MF165, MF235. Industrials: 203, 204. Others with A3-152, AG3-152, AD3-152, A4-203, AD4-203. Replaces Perkins 2554408. 1447048M1 Oil filter spin-on element, 5-3/8" long. Tractors: MF165 gas, MF175, MF180, MF255, MF265, MF275, MF285, MF1080, MF1085, others using A4-212, AG4-212, A4-236, A4-248, A4-318. Replaces Perkins 2654403. MF-2-82

2 ENGINE SYSTEMS Replacement parts to fit 1447031M1 509682M91 3599307M91 Oil filter spin-on element, 7-1/8" long. Tractors: MF1100, MF1105, MF1130, MF1135, MF2775, MF2805. Combines: 740, 750, 760. Others using A4-300, A6-305, A6-354, AT6-354. Replaces Perkins 2654407. Oil Pressure Switches Oil pressure switch, uses blade type wire terminal. For Perkins diesel engines. Tractors: MF135, MF150, MF165, MF175, MF180, MF230, MF235, MF245, MF255, MF265, MF275, MF285 (s/n 9A349239 & up), MF1080, MF1085, MF1100, MF1105, MF1130, MF1135, MF1150, MF1155, MF1505, MF1805. Industrials: 20, 20C, 30, 30B, 30D, 31, 40, 40B, 50, 50A, 50C, 50D, 203, 205, 302, 304, 2135, 3165. Oil pressure switch. Tractors: MF154S, MF174S, MF184-4, MF194F, MF231, MF240, MF250, MF253, MF270, MF274-4, MF282, MF283 (except Brazil), MF290, MF294-4, MF298, MF360, MF362, MF364S, MF375, MF383, MF390, MF393, MF394S, MF398, MF399, MF670, MF690, MF698, MF699, MF2640, MF3050 (to s/n V173002), MF 3060 (to s/n V173002), MF 3070 (to s/n V173002), MF 3090 (to s/n V173002), MF3505, MF3525, MF3545, MF3630, MF3650. Industrials: 20D, 30E, 40E, 50E. Replaces 1423895M91, 1877721M92. 506902M92 1853097M91 731117M91 1750095M1 760029M91 529737M91 Oil Pressure Gauge, Cap & Dipstick Gauge, 80 lb. oil pressure. Tractors: MH44, 55 series, TE20, TO20, TO30, TO35, MF35, MF50, MF65. For 2" hole. Gauge, oil pressure, for instrument panel. Tractors: TO35 with Standard Motors diesel. Replaces 1850377M93. Engine oil level dipstick, all models using Perkins A3-152, AD3-152, A4-203 & AD4-203 engines. Engine oil level dipstick. For Continental gas engines. Tractors: TE20, TO20, TO30, TO35, MF35, F40, MH50, MF50, MF135, MF150. Industrials: 202, 204, 2135. Oil filler cap. All TE, TO models; All MF gas models using clip type. Governor Assembly Governor assembly. For Continental engines. Tractors: TO30, TO35, MF35, F40, MH50, MF50, MF135, MF150, 11 Pony. Industrials: 202, 204, 2135, 2200, 2500. Also services as a unit tractors: MF135, MF150 with Perkins gas. Supersedes & replaces 1002849M91. MF-2-83

2 ENGINE SYSTEMS Tachometers Water Temperature Gauge 193967M91 1751314M91 Tachometer, original style with Ferguson logo. Tractors: TO35, MH50 w/continental gas engines (to s/n 533414). Vintage Iron Tachometer, Ferguson logo, with mounting brackets. Tractors: TO20, TO30 (equipped with generator). Vintage Iron Tachometer Cables UTG25 1877719M92 Temperature Gauge, heat indicator for 2" mounting hole. Complete assembly with bracket & adapter for block. Dial calibrated to 250, extra long 72" capillary line. Gauge, water temperature. For instrument panel. Tractors: MF231, MF240, MF250, MF253, MF270, MF282, MF283 (except Brazil), MF290, MF298, MF2775 (to s/n 9R2805), MF2805 (to s/n 9R2805). Industrials: 20D, 30E, 40E, 50E, 50F. Water Temperature Sending Unit 506331M91 506335M91 508231M91 Tachometer cable assembly, 39". Tractors: TO35 gas (s/n 204181 & up), MF35 gas, MH50 gas, MF50 gas, MF135 Continental gas, MF150 Continental gas, MF165 gas, MF175. Industrials: 30 gas, 35 gas (utility & turf), 202, 204, 2135 gas, 3165 Continental gas. Tachometer cable assembly, 27". Tractors: MF35 diesel (to s/n 227941), MF50 diesel, MF150, MF165 diesel, MF235 diesel orchard, MF245 diesel orchard. Industrials: 30, 31, 203, (to s/n 659000971), 205 (to s/n 659100580). Tachometer cable assembly, 23". Tractors: MF135 Perkins gas & diesel, MF230 diesel (to s/n 9A349238), MF245 diesel except orchard, MF255 with A4-203 diesel. Industrials: 20, 20C diesel (turf, to s/n 9A349236), 40B, 2135. 1877731M92 Sending unit, water temperature. Tractors: MF25, MF130, MF154-4, MF154-S, MF184-4, MF194F, MF231, MF240, MF250, MF253, MF254-4, MF270, MF274-4, MF282, MF283 (except Brazil), MF285 (to s/n 9A34239), MF290, MF294-4, MF298, MF360, MF362, MF364S, MF375, MF383, MF390, MF393, MF394S, MF398, MF399, MF670, MF690, MF698, MF699, MF2640, MF2675, MF2705, MF2745, MF2775, MF2805, MF3050, MF3060, MF3070, MF3090, MF3505, MF3525, MF3545, MF3630, MF3650, MF3660. Industrials: 20D, 30E, 40E, 50E. Replaces 969606M2, 1825118M91. 544198M91 Tachomoter cable assembly, 53". Tractors: MF85 diesel, MF88 diesel, MF255 early production with A4-236 diesel, MF265 diesel (to s/n 9A349238), MF275, MF285 (to s/n 9A349238). Industrials: 50C, 320 Skidder. 882021M91 Tachometer cable assembly, 54". Tractors: MF270, MF282, MF290L. Industrial: 50E. MF-2-84

2 ENGINE SYSTEMS Replacement parts to fit 1005011M92 830862M91 830691M91 742558M91 747542M91 835615M92 3641250M91 3641219M91 Water Pumps Pump less pulley. Tractors: 33, 44, 444, 55, 555. Pump with cast iron body, less pulley. Tractors: TE20, TO20, TO30. Pump less pulley, for Continental Gas engines. 2-3/4" impeller. Tractors: TO35, MF35, F40, MH50, MF50, MF135, MF150. Industrials: 35, 202, 204. Pump with pulley for AD3-152 diesel. Tractors: MF35, MF50. Industrials: 35, 203, 205. Uses repair kit 731774M91. Pump with pulley, for AD3-152 diesel. Tractors: MF135, MF150, MF230, MF235, MF245. Industrials: 20, 20C, 30B, 2135, 2500 forklift. For AG3-152 gas in tractors: MF135 exc. orch., MF150. Industrials: 20 (s/n 152UA18330A & up), 203, 205, 2500 forklift. Replaces 739527M91. Uses repair kit 731774M91. Pump less pulley, for Continental Gas engines. 3" impeller. Tractors: MF65, MF180. Industrials: 302, 304. Pump with pulley, for AD4-203 diesel. Tractors: MF65, MF165, MF255. Industrials: 30, 50, 302, 304. Replaces U5MW0061, 740611M91, 3637372M91. Pump less pulley, for A4-236 diesel & A4-248 diesel. Tractors: MF175, MF180, MF255, MF265, MF270, MF275 (less plug), MF374, MF384 Industrial: 50H. Replaces 41313225, 743064M91, 3637411M91. 4222028M91 4222002M91 835707M92 3641363M91 747611M91 3637466M91 744228M91 Water pump, complete. Tractors: MF399, MF3095, MF3120, MF3125, MF3140, MF3645, MF3655, MF3660, MF6170, MF6180, MF6190, MF8120. Replaces 3637249M91, 3638694M91, 3641860M91, 4131E011, 4131E015, U5MW0092, U5MW0140. Pump, less pulley & back housing. For diesel engines A4-236, AT4-236, A4-248. Tractors: MF375, MF383, MF390, MF390T, MF393, MF398, MF3050, MF3060, MF3070. Replaces 41313218, 41313227, 41313237, 743166M91, 747164M91, 3637468M91, 3638998M91. Pump less pulley & back housing. 3-3/4" impeller. Tractors: MF85, MF88. Pump less pulley, for A4-318 diesel. Tractors: MF285, MF298. Industrials: 70 backhoe loader, 320 skidder. Combine: 540. Includes mounting gaskets. Replaces Perkins U5MW0009. Pump less pulley, for dual thermostats. For diesel engines A6-354, AT6-354. Tractors: MF1100, MF1105, MF1130, MF1135. Replaces 41312382, 41312671, 41312674, 41312681, 41312703, 737900M91, 738810M91, 738836M91, 738892M91, 739483M91. Pump less pulley, for diesel engines A6-372, A6-3724, A6-3544. Combines: 550, 750 (s/n 16915716 & up), 850 (to s/n 1696027543). Replaces Perkins 41313025, 41313033, 41313047; MF 744451M91, 745278M91, 747570M91. Uses repair kit 3637480M91. Pump less pulley, for diesel engines A6-354, A6-3544, AT6-354, AT6-3544. Tractors: MF399 (with belt drive), MF699, MF2640, MF2675, MF3090, MF3505, MF3545, MF3630, MF3650. Replaces 41313027. Use repair kit 747771M91. MF-2-85

2 ENGINE SYSTEMS 4223901M91 731774M91 732591M91 3637480M91 10R1101 181526M1 181528M1 1750296M1 1750081M1 Water pump assembly. Perkins Phaser (GREEN) engines. (Perkins engines 1006.60, 60T, 1004.40, 40T, 42, 1000.42). Tractors: MF4225, MF4235, MF4245, MF4255, MF4265, MF4325, MF4335, MF4345, MF4355, MF4365, MF6235, MF6245, MF6255, MF6260, MF6265, MF6270, MF6280, MF6290, MF8210, MF8220, MF8925, MF8925T, MF8926, MF8926T, MF8937, MF8937T, MF8939, MF8939T. Replaces Perkins number U5MW0190, U5MW0192. Water Pump Repair Kits See water pump listing for engine and model application. Repair kit, services pumps 739527M91 & 742558M91. Repair kit, services pump 740611M91 & 3641250M91. Repair kit, services water pump 3637466M91. Replaces U7LW0020. Repair kit, MF95, Super 95, MF97. Replaces 836996M91. Cooling Group Gaskets Gasket, water outlet elbow. Tractors: TO35, MF35, & MF50. Gasket, thermostat body. Tractors: TO20, TO30, TO35, MF35, MF50. Gasket, support to water pump body. Tractors: TO20, & TO30. Water Pump Pulley Water pump pulley, is used with 830691M91 water pump for Continental 4-cylinder gas engine Z134. Tractors: TO35, MF35, MF135. Industrials: 202, 204. Belts Application Belts MF25 3704187M1 MF30 531371M1 MF35 (to s/n 186976M1 9A38905) MF40 517456M1 MF40B 517344M2 MF50C 517344M2 MF50D 517344M2 MF65 522063M1 MF65 184526M1 MF65 186750M2 MF135 517951M91 MF135 531371M1 MF135 517456M1 MF135 (to s/n 186976M1 9A38905) MF135 843198M1 MF150 (with 186976M1 generator) MF150 517344M2 MF165 186976M1 MF165 843198M1 MF175 531371M1 MF175 843198M1 MF175 190083M1 MF175 513833M1 MF180 4264647M1 MF180 517456M1 MF180 186750M2 MF205 508560M1 MF205-4 508560M1 MF230 531371M1 MF235 531371M1 MF245 531371M1 MF255 531371M1 MF255 517344M2 MF265 517344M2 MF270 2614B059 MF275 517344M2 MF375 3381364M91 MF375 3435748M1 Type Fan & Alternator Fan & Alternator Fan Fan & Alternator Fan Fan Fan Fan, Alternator, & Generator Fan Fan Fan & Alternator (w/58-1/8 belt OC) Fan & Alternator (s/n 9A38905 & up) Fan & Alternator (Orchard style; s/n 9A38905 & up) Fan Fan Fan Fan Fan Fan Fan & Alternator Fan Fan Fan Fan & Generator Fan & Generator (s/n 9A40277) Fan Fan & Generator Fan & Generator Fan & Alternator Fan & Alternator Fan & Alternator Fan & Alternator Fan Fan Fan & Alternator (w/ 1/2 belt TW) Fan Fan & Alternator Air Conditioning MF-2-86

2 ENGINE SYSTEMS Replacement parts to fit Application MF383 MF383 MF390 MF390 MF398 MF670 MF690 MF698 MF1030 MF1030 MF1045 MF1080 MF1100 MF1100 MF1100 MF1100 MF1105 MF1105 MF1130 MF1130 MF1130 MF1140 MF1150 MF1155 MF1500 MF1505 MF1540 MF1560 MF1800 MF1805 MF2640 MF2640 MF2640 MF2640 Belts 3381364M91 3435748M1 3381364M91 3435748M1 2614B059 1690691M1 1690691M1 3435747M1 3435747M1 3435748M1 3436669M1 522063M1 512431M1 3389525M1 517951M91 3435747M1 3436669M1 517951M91 3389525M1 517951M91 3435747M1 3704187M1 1614371M1 3040966M1 530330M91 530330M91 1690691M1 4264647M1 530330M91 530330M91 3381364M91 1447418M91 3040966M1 3320327M1 Type Application Fan & Alternator MF2675 Air Conditioning MF2675 Fan & Alternator Air Conditioning MF2675 Fan & Alternator (w/ 1/2 belt TW) MF2675 Fan & Air Conditioning Fan & Air MF2705 Conditioning Air Conditioning MF2745 Fan & Alternator MF2770 (w/42-1/4 belt OC) MF2775 Fan & Alternator MF2800 (w/41-3/4 belt OC) MF2805 Fan & Alternator MF3090 Air Conditioner Fan & Alternator MF3090 Fan & Alternator (w/o A/C; w/57-1/4 belt MF3090 OC) Fan & Alternator MF3505 (w/58-1/8 belt OC) MF3505 Air Conditioning Air Conditioning MF3505 Fan & Alternator (w/58-1/8 belt OC) MF3505 Fan & Alternator (to s/n 9B15389; MF3505 w/single belt) Fan & Alternator MF3525 (w/dual belts) MF3525 Air Conditioning Fan & Alternator MF3525 Air Conditioning (w/47-1/4 belt OC) MF3525 Alternator & Air Conditioning MF3545 Alternator MF3545 Alternator Alternator MF3545 Fan Alternator MF3545 Alternator Fan MF3660 Fan & Alternator (w/60-1/4 belt OC) MF4800 Air Conditioning Alternator (w/39-7/8 MF4800 belt OC) Belts 3381364M91 3386214M1 4264647M1 3320327M1 4264647M1 1612892M91 1612892M91 1612892M91 1612892M91 1612892M91 2614B059 1447418M91 522063M1 3381364M91 3386190M91 3320327M1 3386214M1 1614371M1 3381364M91 3386190M91 3386214M1 1614371M1 3381364M91 3386190M91 3386214M1 1614371M1 3386214M1 595851M1 517456M1 Type Fan Air Conditioning (w/45-7/8 belt OC) Air Conditioning (w/44-7/8 belt OC) Water Pump & Alternator (s/n 9R414 & up) Air Conditioning (to s/n 9R5659) Fan Fan Fan Fan Fan Fan & Alternator (w/59-1/4 belt OC) Fan & Alternator (w/60-1/4 belt OC) Fan & Air Conditioning Fan & Alternator Fan & Alternator (w/55-3/4 belt OC) Fan & Alternator (w/39-7/8 belt OC) Air Conditioning (w/45-7/8 belt OC) Air Conditioning (w/47-1/4 belt OC) Fan & Alternator Fan & Alternator (w/55-3/4 belt OC) Air Conditioning (w/45-7/8 belt OC) Air Conditioning (w/47-1/4 belt OC) Fan & Alternator Fan & Alternator (w/55-3/4 belt OC) Air Conditioning (w/45-7/8 belt OC) Air Conditioning (w/47-1/4 belt OC) Fan & Air Conditioning Air Conditioning (to s/n 9D004000) Fan & Alternator (to s/n 9D003701) MF-2-87

2 ENGINE SYSTEMS Application MF4840 MF4840 MF4880 MF4880 MF4900 MF4900 MF5435 MF5465 MH44 TE20 TEA20 TO20 TO30 2200 Industrial 1884777M1 1884738M1 Belts 595851M1 517456M1 595851M1 517456M1 595851M1 517456M1 3389525M1 595851M1 35645A 181636M1 181636M1 181636M1 181636M1 3436669M1 Fan Blades Type Air Conditioning (to s/n 9D004000) Fan & Alternator (to s/n 9D003701) Air Conditioning (to s/n 9D004000) Fan & Alternator (to s/n 9D003701) Air Conditioning (to s/n 9D004000) Fan & Alternator (to s/n 9D003701) Fan & Alternator (non-high Visibility) Air Conditioning Fan (w/continental gas) Fan Fan Fan Fan Fan & Generator Fan blade, front blade for 2-piece fan. Tractors: MF240, MF250, MF253. Industrials: 20D, 30E, 40E. Use with blade 1884738M1. Fan blade, rear blade for 2-piece fan. Tractors: MF240. MF250, MF253. Industrials: 20D, 30E, 40E. Use with blade 1884777M1. 13509G 3280783M1SR 3280783M1 184528M93SR Radiator cap for non pressurized systems. Fits on inside of neck. 2.108" tab to tab, 2.806" ID cap. Tractors: Massey Harris: Pacemaker, Challenger. Vintage Iron Safety Release Radiator Cap 13 psi. For radiator overflow reservoir systems, fits ¾" deep neck. Tractors: MF205, MF210, MF220, MF1010, MF1020, MF1030, MF1035, MF1040, MF8780P. OE Type Radiator Cap 13 psi. For radiator overflow reservoir systems, fits ¾" deep neck. Tractors: MF205, MF210, MF220, MF1010, MF1020, MF1030, MF1035, MF1040, MF8780P. Safety Release Radiator Cap 10 psi. Fits ¾" deep neck. Tractors: MF154-4, MF184-4, MF240, MF251E, MF253, MF254, MF263, MF274, MF281 Special, MF294, MF360, MF362, MF375, MF383, MF390, MF390T, MF393, MF396, MF398, MF399, MF451, MF471, MF481, MF670, MF690, MF698, MF699, MF750SP, MF760SP,, MF850, MF860, MF2210, MF3120T, MF3660, MF4235, MF4243, MF4255, MF4325, MF4345, MF4355, MF5200, MF6170, MF6180, MF6265, MF6280, MF6290, MF8120, MF8160, MF8240, MF8250, MF8450, MF8460. Radiator Cap & Drain Plug 1016199M1 Drain cock, fits all: TO & MF models. 1/4" NPT. 180224M91 Radiator cap. Tractors: TO20, TO30, TO35, MF50, MF135, MF150, gas or diesel. MF-2-88

2 ENGINE SYSTEMS Replacement parts to fit 184528M93 968816M2 180224M91SR OE Type Radiator Cap 10 psi. Fits ¾" deep neck. Tractors: MF154-4, MF184-4, MF240, MF251E, MF253, MF254, MF263, MF274, MF281 Special, MF294, MF360, MF362, MF375, MF383, MF390, MF390T, MF393, MF396, MF398, MF399, MF451, MF471, MF481, MF670, MF690, MF698, MF699, MF750SP, MF760SP, MF850, MF860, MF2210, MF3120T, MF3660, MF4235, MF4243, MF4255, MF4325, MF4345, MF4355, MF5200, MF6170, MF6180, MF6265, MF6280, MF6290, MF8120, MF8160, MF8240, MF8250, MF8450, MF8460. OE type radiator cap, 7 psi. For "B" size 2-11/16" OD. Fits ¾" deep filler neck. Tractors: MF366, MF2645, MF2685, MF2725, MF3050, MF3060, MF3065, MF3070, MF3080, MF3085, MF3090, MF3095, MF3115, MF3120, MF3125, MF3140, MF3610, MF3630, MF3635, MF3645, MF3650, MF3655. Safety release radiator cap, 7 psi. Fits ¾" deep neck. Tractors: MF35, MF40, MF65, MF90, MF135, MF150, MF165, MF175, MF202 Industrial, MF204 Industrial, MF230, MF235, MF240, MF245, MF250, MF255, MF265, MF270, MF275, MF285, MF290, MF294, MF298, MF540SP, MF550, MF550SP, MF850, MF1085, MF1105, MF1135, MF1155, MF1500, MF1505, MF1800, MF1805, MF231S, MF2640, MF2675, MF2705, MF2745, MF2770, MF2775, MF2805, MF300SP, MF3070, MF3090, MF3120, MF3140, MF3505, MF3525, MF3545, MF3625, MF3630, MF3660, MF3670, MF3680, MF3690, MF4800, MF4840, MF4880, MF4900, MF8560, MF9720, TO20, TO30, TO35. 194275M94 180705M1 181623M1 1680547M92 885579M93 539919M91 579004M91 Radiator Assemblies Radiator assembly with cap, for gas or diesel engines. Tractors: MF135 (except vineyard) with Perkins gas (prior to s/n 9A117590), MF135 vineyard with Perkins diesel (prior to s/n 9A117609). Industrials: 20, 2135. Pad, radiator mounting, use with radiator 194275M94. Tractors: MF135. Industrials: 20, 2135. Also for radiators on tractors: TO35, MF35, MF230, MF235 exc. orch., MF240, MF245 exc. orch., MF250, MF253; industrials: 20C turf, 20D, 30E, 35, 40E, 202, 203, 204, 205. Radiator assembly, for Z120, Z129, Z134 Continental engines. Tractors: TE20, TEA20, TO20, TO30, TO35, MF35. Industrials: 202, 204 (prior to s/n 342499). Can replace radiators 180291M1 & 186830M91. Radiator assembly. Tractors: MF240, MF250. Industrials: 20D, 30E, 40E manual steering, 2WD. Radiator assembly. Tractors: MF165UK, MF185, MF188. Core Height: 19-1/8" Core Width: 15-1/8" 3 row, 8 FPI. Radiator assembly. Tractors: MF230 (prior to s/n 9A284347), MF245 gas (prior to s/n 9A28282764), MF245 diesel (prior to s/n 9A282759, with 4-1/2" neck). Core Height: 18-1/2" Core Width: 15", 3 row, 8 FPI. Radiator assembly. Tractors: MF230 (s/n 9A284347 & up), MF245 Gas (s/n 9A282764 & up, with 3-1/2" neck), MF245 Diesel (s/n 9A282759 & up). Core Height: 18-1/2" Core Width: 15-1/2" 3 row, 9 FPI. MF-2-89

2 ENGINE SYSTEMS 531981M94 Radiator, 4-11/16" filler neck. Overall Dimensions: 25-1/8" x 16-1/16" Core Deminsions: 19" x 15-1/4" x 2-1/8" Inlet 1-1/2" Outlet 1-1/2", 3 row Tractors: MF255, MF265 (early Diesel, w/ oil cooler). Upper Radiator Hoses 531982M94 1695721M2 Radiator, 5-3/16" filler neck. Overall Dimensions: 25-1/8" x 16-1/16" Core Dimensions: 19" x 15-1/4" x 2-1/16" Inlet 1-1/2", Outlet 1-1/2", 3 row Tractors: MF 255 (later Diesel). Radiator Assembly. Tractors: MF375, MF383, MF390, MF390T, MF393, MF398, MF399. 180085M1 186826M1 Hose, radiator upper. For Continental gas engine. Tractors: TO20, TO30, TO35, MF35. Industrials: 202 (prior to s/n 306493), 204 (prior to s/n 342499). For Perkins gas or diesel. Tractors: MF35, MF50, MF135, MF230 (prior to s/n 9A243032), MF235 (except orchard). Industrials: 20, 203, 205, 2135. 5.5" long, 1.50" I.D., 1.82" O.D. Hose, radiator upper. Tractors: TO35 (s/n 204181 & up), MF35 gas. 894319M92 186733M91 181634M1 836000M91 Radiator assembly. Tractors: MF35 Diesel, MF203, MF205 Diesels. Core Height: 23-1/8" Core Width: 16" 3 row, 9 FPI Radiator assembly (Diesel only). Tractors: MF50, MF50A, MF65, MF302, MF304. Core Height: 22-1/4" Core Width: 16-5/16" Thermostats Thermostat. Fits in upper radiator hose, 160. 2-1/4" long for 1-1/2" I.D. hose. Tractors: TO20, TE20, TO30. Thermostat. 160. Tractors: TO35, MF35, F40, MF50. 194299M1 186654M1 194738M1 194736M1 1869514M1 539808M2 Hose, radiator upper. For Z134 or Z145 Continental gas engine. Tractors: MF135, MF230 (prior to s/n 9A243032), MF235. Industrials: 2135. Hose, radiator upper. For Perkins 4-203 diesel engine. Tractors: MF65. Industrials: 50, 50A, 302, 304, 356. Hose, radiator upper. For Perkins 4-203 diesel engine. Tractors: MF165 except with dual tricycle, MF255. Industrials: 30, 3165. Hose, radiator upper. Tractors: MF165 with Perkins gas, MF175 with Perkins gas or diesel, MF255 gas or A4-236 diesel, MF265, MF275. Industrials: 30 gas, 31. Hose, radiator upper. Tractors: MF231, MF240, MF250, MF253. Industrials: 20D, 30E, 40E. Replaces 897455M1. Hose, radiator upper. For diesel engines. Tractors: MF230 (s/n 9A243032 & up), MF245 (except orchard). Industrials: 20C turf. MF-2-90

2 ENGINE SYSTEMS Replacement parts to fit Lower Radiator Hoses Other Cooling Hoses 180145M1 180783M1 186968M1 519437M2 194737M1 511951M1 1860374M2 544080M1 187554M1 194739M2 184325M1 Lower hose. Tractors: TO20, TO30. 1.85" O.D., 1.50" I.D., 13.50" long. Hose, radiator lower. For Continental gas engines. Tractors: TO35, MF35, MF135. Industrials: 202, 204, 2135. 1.85" O.D., 1.50" I.D., 10.70" long. Hose, radiator lower. For Perkins diesel engines. Tractors: MF35, MF135, MF230, (prior to s/n 9A243032), MF235 (except orchard). Industrials: 20, 35 utility, 203, 205, 2135. Hose, radiator lower, water pump inlet. Tractors: MF135 with Perkins gas. Hose, radiator lower. Tractors: MF175 diesel, MF255 with A4-236 diesel, MF265 diesel (except orchard). Hose, radiator lower. Tractors: MF235 orchard diesel, MF245 orchard diesel. Industrials: 20C (except turf), 30B diesel, 30D, 40. Hose, radiator lower. Tractors: MF231, MF240 (except with hydrostatic steering), MF250. Industrials: 20D, 30E. Hose, radiator lower to metal tube. Tractors: MF230 (s/n 9A243032 & up), MF245 (except orchard). Industrials: 20C turf. Hose, radiator lower. For Perkins 4-203 diesel engine. Tractors: MF65. Industrials: 50, 50A, 302, 304, 356. Hose, radiator lower. For Perkins 4-203 diesel engine. Tractors: MF165 (except with dual tricycle), MF255. Industrials: 30, 3165. Radiator hose, lower. Tractors: F40, MF165, MF50, MF65, MH50. 732443M1 747936M91 731174M1 747942M91 744671M1 3583543M2 Hose, water pump to block inlet. For Perkins gas or diesel engines. Tractors: MF35, MF50, MF135, MF150, MF154-4, MF230, MF231, MF235, MF240, MF245, MF250, MF254-4. Industrials: 20, 20C, 20D, 30B, 30D, 30E, 40, 203, 205, 2135. Replaces 34821422. Hose, by-pass, water pump to thermostat housing. For Perkins gas or diesel engines. Tractors: MF35, MF50, MF135, MF150, MF154-4, MF230, MF231, MF235, MF240, MF245, MF250, MF254-4. Industrials: 20, 20C, 20D, 30B, 30D, 30E, 40, 203, 205, 2135. Replaces 731256M1. Hose, inlet, water pump to block. For diesel engines. Tractors: MF65, MF165, MF255 with AD4-203. Industrials: 30, 40B, 50, 50A, 302, 304, 3165. Replaces 747941M91. Hose with clamps, by-pass, water pump to thermostat housing. For Perkins 4-203 diesel engines. Tractors: MF65, MF165, MF255. Industrials: 30, 40B, 50A, 302, 304. Replaces 742316M1. Hose, pump to inlet connections. Tractors: MF1100 diesel, MF1105, MF1130 diesel, MF1135 diesel. Replaces 735604M1. Heater for Intake Manifold Heater, for intake manifold on Perkins diesel engines. 3/8" thread small end,.865" thread large end. Tractors: MF154-4, MF184-4, MF240, MF250, MF270, MF274-4, MF399, MF670, MF690, MF698, MF3070, MF3090. Replaces Perkins 2666108. MF-2-91

2 ENGINE SYSTEMS Engine Heaters Manifolds 839071M94 GE361 Engine heater, 3/4" pipe thread, 400 watts, 115-volt. Fits most Massey Ferguson diesels. Replaces GE360. Replacement cord: GE360C. Adapter, 3/4" FNPT, 1-1/4" bushing, 32mm O.D. Used with GE360. 740221M1 Exhaust manifold. For AD3-152 Perkins diesel engines. Tractors: MF231, MF240, MF250. Industrial: 20D with horizontal exhaust. Requires 2-735016M1 & 1-3640488M1 gaskets. Replaces 37781571. GE362 Engine heater. 3/4" pipe thread, 400 watts, 115 volt. Fits most Perkins diesels. Contains 1 GE360 & 1 GE361. 19841A91 Frost plug engine heater, 1-1/4" dia. clamp & o-ring mounting, 600 watts. For Massey Ferguson models. Tractors: MF135, MF150, MF230, MF231, MF235, MF240, MF245, MF250, MF253, MF254-4, MF282, MF283, MF298, MF360, MF364S, MF399 with 354.4 eng., MF698. Industrials: 20, 20C, 30B, 40. Replacement cord: 773320M1, 12" long. 1040903M91 Manifold, universal intake & exhaust, includes gasket set. Tractors: TO20, TO30, TO35, MF35, MF135. Replaces 1750343M91. Exhaust Elbow G176E601ELB Exhaust elbow. Gas tractors: MF65 533446M2 Exhaust elbow. Tractors: MF255, MF265, MF275. 1500003M1 Manifold, intake & exhaust. Tractors: Massey Harris Pony. 736648M1 535925M1 Exhaust elbow. For Perkins diesel engines in tractors: MF1105, MF1130, MF1135. Exhaust elbow, Vertical diesel. Tractors: MF235, MF245. G176E601 Exhaust manifold, less gasket. For gas engines Tractors: MF65. 37782350 Exhaust manifold, for turbocharged engines. Tractors: MF1105, MF1130, MF1135, MF2705, MF3525, MF3545, MF3630, MF3650 (w/ci engines w/13 bolt mounting). MF-2-92

2 ENGINE SYSTEMS Replacement parts to fit 180104M1 Manifold Gaskets Gasket, exhaust manifold to pipe or elbow. Tractors: TO35, MF35, MF50, MF135. Industrials: 35 Utility, 203, 205. Custom Vertical Muffler Assemblies & Pipes 735016M1 3640488M1 181531M2 1750045M1 736754M1 Gasket, exhaust manifold to cylinder head. For Perkins diesel engines. Tractors: MF135, MF150, MF154-4, MF154-4S, MF230, MF231, MF235, MF240, MF245, MF250, MF254-4. Industrials: 20D, 30E. 2 required. Gasket, exhaust manifold to pipe or elbow. For Perkins diesel engines. Tractors: MF135, MF150, MF154-4, MF154-4S, MF230, MF231, MF235, MF240, MF245, MF250, MF254-4. Industrials: 20D, 30E. Replaces 827877M1. Gasket, carburetor to manifold. Tractors: TO20, TO30, TO35, MF35, F40, MF50, MF135, MF150. Industrials: 202, 204, 2135. Gasket, manifold. Tractors: TO20, TO30, TO35, MF35, F40, MF50, MF135. Gasket, exhaust manifold to cylinder head. For Perkins diesel engines. Tractors: MF175 (vertical exhaust), MF180, MF270, MF283 (except Brazil), MF290, MF362. Industrials: 31 (horizontal exhaust), 50E. 2 required. M112 M115 M1111 M134 M135 Vertical 2-piece muffler assembly. Flared inlet, 1-1/2" outlet OD, 48" OA length. Tractor: TE20, TO20, TO30. Vertical 2-piece muffler assembly with 3-bolt flange. 1-1/2" outlet OD, 47" OA length. Tractors: TO35. Vertical 2-piece muffler & pipe. 2" inlet ID, 2" outlet OD, 31" OA length. Tractor: MF65. Custom-designed upright muffler & pipe with 3-bolt flange. 1-1/2" outlet OD, 42" OA length. Tractors: MF35 (with Perkins diesel), MF135 (with Continental gas). Vertical one piece muffler & pipe assembly, custom design shown. For Perkins gas or diesel engines. Tractor: MF135. Pipe has 3-bolt flange inlet, muffler outlet 1-3/4" O.D., shell length 12, shell 4-1/2" O.D. Use with gasket 3640488M1. 194742M1 Gasket, exhaust manifold to elbow. For Perkins diesel engines. Tractors: MF175 (vertical exhaust), MF180, MF270, MF283 (except Brazil), MF290, MF362. Industrials: 31 (horizontal exhaust), 50E. 1 required. MF-2-93

2 ENGINE SYSTEMS Customized Horizontal Muffler Assemblies Exhaust Weathercaps Improved one-piece design for popular models. M500 M119 M132 M136 1694961M5 1694963M5 Muffler & pipe assembly. Tractors: TO20, TO30. Replaces 505545M92 muffler & 180460M1 pipe. Muffler & pipe assembly with 3-bolt flange. Tractors: TO35, MF35 (Continental gas). Replaces 505545M92 muffler & 181600M92 pipe. Uses gasket 180104M1 (not included). Muffler & pipe assembly with 3 bolt flange. Tractor: MF35 (Perkins diesel). Replaces 505545M92 muffler & 189678M91 pipe. Muffler & pipe assembly with 3-bolt flange. Tractor: MF135 (Perkins gas & diesel). Replaces 539525M91 muffler & 522584M91 pipe on late models, also will replace 505545M92 & 507518M91 on early models. Uses gasket 3640488M1 (not included). Muffler Assemblies Muffler assembly with 3 hole mounting. Tractors: MF365, MF375, MF383, MF390. Muffler assembly with 4 hole mounting. Tractors: MF390 (to s/n B18008), MF390T, MF393, MF398. Replaces WC0 WC1 WC2 WC3 WC4 WC5 WC6 WC7 WC8 WC9 WC10 WC11 WC12 WC13 WC14 WC15 MIN. EHAUST O.D. 1" 1-1/4" 1-1/2" 1-3/4" 2" 2-1/4" 2-1/2" 2-3/4" 3" 3-1/4" 3-1/2" 3-3/4" 4" 4-1/4" 4-1/2" 5" MA. EHAUST O.D. 1-3/16" 1-7/16" 1-11/16" 1-15/16" 2-3/16" 2-7/16" 2-11/16" 2-15/16" 3-3/16" 3-7/16" 3-11/16" 3-15/16" 4-3/16" 4-7/16" 4-11/16" 5-3/16" Universal Muffler Clamps 1694965M1 Muffler assembly with 3 hole mounting. Tractors: MF399. MCK-2 181461M91 MCK-3 Muffler Clamp Kits Muffler clamp kit. Tractors: TO20, TO30. Kit contains 2 high strength aluminum clamps, nuts, bolts, & lockwashers. Replacement clamp half for MCK-2. Same as MCK-2 with heavy-duty malleable clamps. Replaces MC150 MC158 MC134 MC178 MC200 MC225 MC250 MC275 MC300 MC350 Full 360 saddle clamps with nuts. O.D. designation refers to pipe size. PIPE O.D. 1-1/2" 1-5/8" 1-3/4" 1-7/8" 2" 2-1/4" 2-1/2" 2-3/4" 3" 3-1/2" MF-2-94

2 ENGINE SYSTEMS Replacement parts to fit Horizontal Mufflers for Gas & Diesel Tractors Application Muffler TO20, TO30 Continental gas 505545M92 TO35 Continental Gas 505545M92 MF35 Continental gas, 505545M92 Perkins diesel MF35 Perkins diesel 505545M92 MF50, MH50, F40 gas 182609M91 MF50 Perkins diesel 187184M91 MF65 Continental gas 184207M91 MF65 Perkins diesel 186886M91 MF135 Continental gas 505545M92 MF135 Perkins to s/n 505545M92 9A99582 MF135 Perkins s/n 9A99582 539525M91 & up MF150 Continental gas 539523M92 MF150 Continental gas 539523M92-TP MF150 Perkins gas to s/n 539523M92 9A102611 MF150 Perkins gas to s/n 539523M92-TP 9A102611 MF150 Perkins gas s/n 539525M91 9A102611 & up MF150 Perkins gas s/n 539523M92-TP 9A102611 & up MF150 Perkins diesel 539525M91 MF150 Diesel with generator 539523M92 MF150 Diesel with generator 539523M92-TP MF165, MF175, MF180 539523M92 MF165, MF175, MF180 539523M92-TP MF240 to s/n 2773N01001, 539523M92 MF245, MF255, MF265, MF275 MF240 to s/n 2773N01001, 539523M92-TP MF245, MF255, MF265, MF275 Tractors: Massey-Harris 767994M91 (1942-1957) (Gas & Diesel), 20, 20K, 22, 22K (Except 1948), 30, 30K, 33, 333, 44, 44SPL, 44D, 44K, 44-6, 444, 81, 82, 101JR, 101SR, 102SR. Inlet I.D. 1-1/2" 1-1/2" 1-1/2" 1-1/2" 1-15/16" 1-3/4" 1-15/16" 1-3/4" 1-1/2" 1-1/2" 1-3/4" 2" 2" 2" 2" 1-3/4" 2" 1-3/4" 2" 2" 2" 2" 2" 2" 2-3/8" Outlet O.D. 1-1/2" 1-1/2" 1-1/2" 1-1/2" 1-3/8" 1-3/4" 1-3/8" Bent 1-1/2" 1-1/2" 1-3/4" 2" 2" 2" 2" 1-3/4" 2" 1-3/4" 2" 2" 2" 2" 2" 2" 2-1/2" Overall Length 34" 34" 34" 34" 18-1/2" 34" 18" 40" 34" 34" 39" 32" 32" 32" 32" 39" 32" 39" 32" 32" 32" 32" 32" 32" 21" Diameter 3-1/4" 3-1/4" 3-1/4" 3-1/4" 3-1/4" 3-1/4" 3-1/4" 3-1/4" 3-1/4" 3-1/4" 4-1/4" 3-1/4" 3-1/4" 3-1/4" 3-1/4" 4-1/4" 3-1/4" 4-1/4" 3-1/4" 3-1/4" 3-1/4" 3-1/4" 3-1/4" 3-1/4" Body Style Round Round Round Round Round Round Round Round Round Round Round Round Round Round Round Round Round Round Round Round Round Round Round Round Round Inlet Clamp MC150 MC150 MC150 MC150 MC200 MC134 MC200 MC134 MC150 MC150 MC134 MC200 MC200 MC200 MC200 MC134 MC134 MC134 MC200 MC200 MC200 MC200 MC200 MC200 Outlet Clamp MC150 MC150 MC150 MC150 MC150 MC134 MC150 MC150 MC150 MC134 MC200 MC200 MC200 MC200 MC134 MC134 MC134 MC200 MC200 MC200 MC200 MC200 MC200 MFLD to MUFF Pipe 181600M92 181600M92 182614M1 184209M2 673511M91 194268M92 507518M92 522584M92 MF-2-95

2 ENGINE SYSTEMS Vertical Mufflers for Gas & Diesel Tractors Application Muffler TO20, TO30 Continental M112 gas TO35 Continental Gas M115 MF35 Continental gas, 181867M91 Perkins diesel MF50, MH50, F40 gas 182609M91 MF50 Perkins diesel 187184M91 MF65 Continental gas M1111 MF65 Perkins diesel 187184M91 MF85, MF88 Continental 187269M91 gas MF85, MF88 diesel 187553M92 MF135 Continental gas M134 MF135 Perkins gas & diesel 181867M91 MF150 Continental gas 539525M91 MF150 Perkins diesel to s/n 539523M92 9A107187 MF150 Perkins diesel to s/n 539523M92-TP 9A107187 MF150 Perkins diesel s/n 539525M91 9A107187 & up MF150 Diesel with 539525M91 generator MF165, MF175, MF180 523394M91 MF165, MF175, MF180 194431M95 Economy muffler MF245, MF255, MF265, 578090M92 MF275 MF245, MF255, MF265, 578090M92-TP MF275 MF285, MF1085 oval 535950M91 MF1100 gas and diesel - 513563M92 round MF1100 gas and diesel - 530690M91 oval MF1130 turbo 522421M91 MF1105, MF1135 528068M91 Inlet I.D. Flared 3-bolt flange 1-7/8" 1-15/16" 1-3/4" 2" 1-3/4" 2-13/16" 2-1/4" 3-bolt flange 1-7/8" 1-3/4" 2" 2" 1-3/4" 1-3/4" 2-1/8" 2-1/8" 2-1/8" 2-1/8" 2-3/4" 2-3/4" 2-3/4" 3-1/2" 3-7/16" Outlet O.D. Overall Length 1-1/2" 48" 1-1/2" 47" 2" 34" 1-3/8" 18-1/2" 1-3/4" 34" 2" 31" 1-3/4" 34" 2-1/4" 38" 2-1/4" 37" 1-1/2" 42" 2" 34" 1-3/4" 39" 2" 32" 2" 32" 1-3/4" 39" 1-3/4" 39" 2" Bent 40" 2" Bent 40" 2" 37" 2" 37" 2-3/4" 24" 2-3/4" 32" 2-3/4" 32" 3-1/2" 32" 3-1/2" 28" Diameter -- -- 4-1/4" 3-1/4" 3-1/4" -- 3-1/4" 4-1/4" 4-1/4" -- 4-1/4" 4-1/4" 3-1/4" 3-1/4" 4-1/4" 4-1/4" 5-1/2" 4-1/4" 3-1/4" 3-1/4" 6" x 10" 5-1/2" 5" x 11" 6" x 9-1/2" 6" x 10" Body Style Inlet Clamp -- -- Round Round Round -- Round Round Round -- Round Round Round Round Round Round Round Round Oval Oval Oval Round Oval Oval Oval MC200 MC200 MC134 MC134 MC225 MC225 MC178 MC134 MC200 MC200 MC134 MC134 MC225 MC225 MC225 MC225 MC275 MC275 MC275 MC350 MC350 Outlet Clamp MC200 MC150 MC134 MC134 MC225 MC225 MC200 MC134 MC200 MC200 MC134 MC134 Rain Cap WC4 WC3 WC3 WC5 WC5 WC4 WC3 WC4 WC4 WC3 WC3 WC4 WC4 WC7 WC7 WC7 WC10 WC10 MF-2-96

3 ELECTRICAL Replacement parts to fit Side Mount Distributor Distributor Repair Parts 182852M91-TP Information For Ordering Distributor Repair Parts NOTE: Original style distributor 182852M91-TP has been supplied by Tisco since February 1987 and replaces Tisco distributor 182852M91-TIS. Visual identification is necessary when ordering replacement parts. 182852M91-TP (has external oiler and terminal for coil wire). 182852M91-TIS (no external oiler and has 14" wire attached to housing). Original style side-mount distributor assembly, complete with rotor & cap. Replaces TISCO 182852M91-TIS. Tractors: TO20, TO30, TO35, MF35 (prior to s/n 245932), F40, MF50 (prior to s/n 536248). Replaces 1111722, 1111740, (MF181686M91), 1112570, 1112586. Spark Plug Wiring Set FET12300A MF12106A MF12200A MF12171AA Repair parts for 182852M91-TP original-style distributor supplied by TISCO since February 1987. Condenser Cap (A) Rotor (B) Points (C) MF12176 Cam & weight assy. (D) Repair parts for 182852M91-TIS. Replaced older-style distributor supplied by TISCO through January 1987. SWS259 SWS260 Spark plug wiring set, waterproof neoprene wire core. Universal, 4 cylinder. Waterproof neoprene cables with distributor nipples & plug end clips and wire core. Tractors: 6 cyl. IBK1009 IGP1016D IGS2224LB Not for use in original MF distributor Cap Rotor Points IAT3076HS Condenser MF-3-97

3 ELECTRICAL Ignition Parts Ignition Kits Less Rotor Contain: Points, Gauge, Condenser Ignition Kits With Rotor Contain: Points, Gauge, Condenser, Rotor Application Tune Up Kit Tractors: TO20, TO30, TO35, MF35, MF50, MF65, MF85, MF88, MF-ITK-10 MF90. Combines: 92, 592. Industrial Tractor: 202, 204, 302, 304, 356 Tractor Shovel For DELCO distributor with clip-held cap Tractors: MF35, MF50, MH50, MF65, MF135, MF150, MF165, MF-ITK-40 MF175, MF180, MF1100. Industrials: 202, 204, 302, 304, 356 For DELCO distributor with screw-held cap Tractors: TE20, TEA20 For LUCAS distributor Tractors: 11, 16, 21, 22, 22K, 23, 23K, 30, 30K, 33, MH44, 44LP, 44-6, 44-6K, 44 Special K, 44 Special LP, 55, 55LP, 333, 333K, 444, 444K, 444LP, 555, 555K, 555LP, 101 Jr. Combines: 26, 27, 27L, 35, 60, 70, 72, 80, 82, 90, 92, Super 92. Balers: 1. Industrials: 20, 35, 303, 402, 404. Windrowers: 34. Forage Clippers: 2, 20 For AUTOLITE distributor Tractors: MH44-6. Combines: 92, Super 92 For IGZ distributor Combines: 300 For AUTOLITE distributor Combines: 410 Tractors: MF230, MF235 For PRESTOLITE distributor Autolite Spark Plugs Ignition Kit w/rotor ATK1DCR ATK10DSR ATK2ALR ATK2ALR Ignition Kit Less Rotor ATK1DC ATK10DS ATK30MH ATK2AL Electronic Ignition Kit ED4C ED4CP6 ED4S ED6S Spark Plugs AL386 AL386 AL386 AL295 AL386 Replaces AL65 AL295 AL303 AL306 AL386 AL405 AL3076 Heat Range Medium Hot Medium Hot Medium Medium Hot Medium Hot Medium Hot Cold Thread diameter (14mm) (14mm) (14mm) (14mm) (18mm) (14mm) (18mm) Reach 3/4" 3/8" 3/8" 3/8" 1/2" 3/4" 5/8" Hex size 13/16" 13/16" 13/16" 13/16" 7/8" 13/16" 15/16" Tip type Power Standard Standard Standard Standard Standard Standard Plug type Non-resistor Non-resistor Resistor Resistor Resistor Resistor Non-resistor Champion Cross Reference N12Y, N12YC, N13Y J8, J8C, UJ8 J5, J6, J6C, J6J, RJ6, RJ6C, UJ6, J7, J7J, RJ7 RJ8, RJ8C, J11, J11J, RJ11, UJ11G D10, K13, D14, M14, RD14, K15J, D16, D16J, RD16, UD16, D21, D89D Replaces #376, BT8, 18-8, D16 N6, N6C, RN6, N8, N21, RN79G W10, W14, C16C, W18, W20 MF-3-98

3 ELECTRICAL Replacement parts to fit Ignition Parts Application Tractors: TO20, TO30, TO35, MF35, MF50, MF65, MF85, MF88, MF90. Combines: 92, 592. Industrial Tractor: 202, 204, 302, 304, 356 Tractor Shovel For DELCO distributor with clip-held cap Tractors: MF35, MF50, MH50, MF65, MF135, MF150, MF165, MF175, MF180, MF1100. Industrials: 202, 204, 302, 304, 356 For DELCO distributor with screw-held cap Tractors: TE20, TEA20 For LUCAS distributor Tractors: 11, 16, 21, 22, 22K, 23, 23K, 30, 30K, 33, MH44, 44LP, 44-6, 44-6K, 44 Special K, 44 Special LP, 55, 55LP, 333, 333K, 444, 444K, 444LP, 555, 555K, 555LP, 101 Jr. Combines: 26, 27, 27L, 35, 60, 70, 72, 80, 82, 90, 92, Super 92. Balers: 1. Industrials: 20, 35, 303, 402, 404. Windrowers: 34. Forage Clippers: 2, 20 For AUTOLITE distributor Points 1750877M91 1024923M91 829925M1 1508810M91 Tractors: MH44-6. Combines: 92, Super 92 For IGZ distributor Combines: 300 For AUTOLITE distributor 1508810M91 Combines: 410 1954557 Tractors: MF230, MF235 For PRESTOLITE 1047266M91 distributor Condenser 1024924M91 1024924M91 1024924M91 1508770M91 1508770M91 1508770M91 1024924M91 1508770M91 Rotor 4 Cyl Cap 6 Cyl Cap Dust Cover Coil 1750498M1 1750411M91 1509692M1 1750491M91 1024481M91 1024916M1 1024914M91 1960810 1500293M1 1500831M91 189673M92 1024481M91 MF-3-99

3 ELECTRICAL 180681M93 181679M1 189158M91 194747M91 504809M91 883928M91 192921M91 Ignition & Starter Switches Switch assembly with 2 keys. Tractors: TO20, TO30, TO35, MF35, MF50, MF65. Starter switch, manual. Tractors: TO20, TO30. Push button switch assembly. Tractors: MF35 starter & horn, MF65 starter; others. 5/8" dash or firewall mount. Ignition & starter switch with keys, 3-prong. For gas engines. Tractors: 50, 135, 150, 165, 175, 180, 230, 235, 245, 255, 265, 1100, 1130, 1500, 1800. Industrials: 20, 20C, 30, 30B, 40, 2135, 2200, 3165. Combines: 410. Skid Steer Loaders: 811. Starter switch. For diesel engines. Tractors: 50, 135, 150, 165, 175, 180, 230, 235, 245, 255, 265, 275, 285, 1080, 1085, 1100, 1105, 1130, 1135, 1150, 1155, 1500, 1800. Industrials: 20, 20C, 30, 30B, 31, 40, 50A, 50C, 302, 304, 356, 2135, 2200, 3165. Forklift: 2500. Switch, starter & heat, with key. For slide-on style terminals (4). For diesel engines. Tractors: TO35, MF35, MF50, MF65, MF85, MF88, MF90. Industrials: 35, 203, 205. Optional on some models with switch 192921M91, check terminals before ordering. Switch, starter & heat, with key. For screw-on style terminals (3). For diesel engines. Tractors: MF35, MF50, MF65, MF90. Industrials: 35, 203, 205. Optional on some models with switch 883928M91. Check terminals before ordering. 1874535M3 Switch, starter & heat, 6 prongs, includes 2 keys. Tractors: MF231, MF240, MF250, MF253, MF270, MF282, MF283, MF290, MF298, MF360, MF375, MF383, MF390, MF398, MF3050, MF3060, MF3070, MF3090, MF3505, MF3525, MF3545, MF3630, MF3650, MF3680. Industrials: 20D, 20F, 30E, 30H, 40E, 50E, 50F, 50H, 60H. Combines: 750 (s/n 1696016539 & up), 760 (s/n 1746009413 & up), 850, 855, 860, 865. Replaces: 1097239M91 1690093M91, 18741230M93. Uses key 960128M91. Replacement Ignition Keys 180292M1 Key for switch 180681M93. 192922M1 960128M91 Key for switches 194747M91 & 504809M91. Can replace key #180923M1, 192293M1 & 192923M1. Key for switch 883928M91 & 1874535M3. MF-3-100

3 ELECTRICAL Replacement parts to fit Light Switches Neutral Safety Switches 772954M1 L5067 180683M1 851674M1 LSN425 Light switch with knob 509309M1. Tractors: MF135, MF150, MF165, MF175, MF180, MF230, MF235, MF245, MF250 (prior to s/n 2773N01000), MF255, MF265, MF270, MF275, MF285, MF288 (except Brazil), MF290, MF298, MF1080, MF1085, MF1100, MF1105, MF1130, MF1135, MF1150, MF1155, MF1500, MF1505, MF1800, MF1805. Industrials: 20, 20C, 20D, 30, 30B, 30D, 30E, 31, 40B, 40E, 50C, 50D, 50E, 2135, 3165. Replaces 504812M1, 522812M1. Heavy-duty light switch, plastic knob, 1/2" diameter, two on-positions, fused 20 amps. Ignition and light index switch plate. Anodized black aluminum, 1-13/16" O.D. Tractors: GAS / LP T035, MF35 (to s/n 209484), MF40, MF50 (to s/n 528971), MH50, MF65 (to s/n 685394), MF85, MF88. Industrials: 202 Workbull, 204 Workbull. Vintage Iron Three position light switch. Hi-Lo Charge. Tractors: Massey Harris: Pony, 22, 30, 30K, 44-6, 81, 82, 101 Jr, 101 Sr, 102 Jr, 102 Sr. Vintage Iron Light switch knob. Says "Lights". Tractors: Massey Harris: Pony, 22, 30, 30K, 44-6, 81, 82, 101 Jr, 101 Sr, 102 Jr, 102 Sr. Vintage Iron 181140M94 1679223M2 3381094M1 1752610M2 180776M1 Switch, neutral safety, for bullet type terminal. Tractors: to MF1130; all utility & industrial models. Switch, neutral safety, has blade type terminals. Tractors: MF240*, MF250*, MF253, MF282, MF283 (except Brazil), MF298*, MF360, MF362, MF375, MF383, MF390, MF393, MF398, MF399. Industrial: 40E*. *Optional with 3381094M1. Replaces 888501M2. Switch, neutral safety, has blade type terminals. Tractors: MF25, MF130, MF231, MF240*, MF250*, MF270, MF290, MF298*, MF670, MF690, MF698, MF3505, MF3525, MF3545. Industrials: 20D, 30E, 40E*. *Optional with 1679223M2. Also used for differential lock switch on tractors: MF360, MF362, MF375, MF383, MF390, MF393, MF398, MF399. Replaces 963417M2, 966224M91. Terminal clip, for neutral safety switch. Tractors: MF35, MF50, MF65, MF135, MF150, MF165, MF175, MF180, MF255, MF265, MF285, MF1100, MF1130. Industrials: 20, 20C, 30, 30B, 30D, 40, 40B, 50, 50A, 50C, 50D, 202, 204, 2135, 3165. Neutral safety switch boot. Tractors: MF35, MF40, MF50, MF65, MF85, MF88, MF135, MF150, MF165, MF175, MF180, MF230, MF235, MF245, MF255, MF265, MF275, MF285, MF1080, MF1085, Super 90. Industrials: 20, 20C, 30, 30B, 30D, 31, 40, 40B, 50, 50A, 50C, 50D, 60, 202, 203, 204, 205, 302, 304, 2135, 3165, 2200, 2500, 4500, 6500. Vintage Iron MF-3-101

3 ELECTRICAL Starter Solenoids & Switches Starters 182330M92 182696M91 1047083M91 1028587M91 1055740M91 Solenoid switch, all metal. Tractors: TO35 using 6-volt. Solenoid switch, all metal, 12-volt. Tractors: TO35, F40, MF35, MF50, MF65, MF85, MF90. Industrials: 202, 204, 302, 304, 356 utility gas & LP models. Solenoid assembly, flange mounting to starter. Replaces Delco 1114356 on starters 1108649, 1107503, 1107512, 1108649. Gas & diesel applications. 12-volt. Solenoid assembly, saddle mounting to starter. Services most late models, replaces Delco 1115510, on starters 1113139, 1113683, 1113676, others. 12-volt. Solenoid assembly, replaces Delco 1119879. Tractors: MF97, MF1105, MF1150 (prior to s/n 9B31942), MF1800, MF2745, MF2775, MF2805 & others. Combines: 760 using AV8-540 Perkins diesel 12-volt. Replaces 1022662M91. 4858MFGL 3763362M91 579937M91 Starter assembly, for 6- or 12-volt systems with Continental gas engine. Tractors: TO20, TO30, TO35, F40, MH50, MF50, MF65. Industrials: Early 302, 304, 356. Can replace OEM starters 181541M91/1109457, 182454M92/1107654, 190004M91/1107226, & Tisco starters 7877-E, 81271-E, 85451-E. Uses 1019269M91 drive & 182696M91 solenoid. New Lucas style starter assembly with solenoid. Tractors: MF174-4S, MF184-4, MF194-4F, MF270, MF274-4, 282, 283 (except Brazil), MF290, MF294-4, MF298, MF362, MF375, MF383, MF390, MF390T, MF393, MF398, MF399, MF670, MF690, MF698, MF699, MF3050, MF3060, MF3070. Industrials: 50E. Replaces 1447010M91, 1447301M91, 1868285M3 Can replace 3597372M2 Magneti Marelli starter and 1447698M1 and 1691806M1 Hitachi starter on above models (Lucas 27539, 26410). Starter, NEW, 10 tooth, 12-volt, clockwise. Tractors: MF175, MF180, MF255, MF265, MF275. Industrial: MF10, MF20C, MF20U, MF30, MF30B, MF40, MF40B, MF40U, MF45U, MF50C, MF50E, MF60, MF60B, MF60C, MF60E, MF2500. Replaces 1903117M91, 579937M91, 579936M91. 3763363M91 New Lucas style starter assembly 5 with solenoid, cold climate. Tractors: MF231, MF240, MF250, MF253, MF360. Industrials: 20D, 20E, 30H, 40E. Replaces 1691805M2, 1868283M5. Can replace 3597371M2, 1680065M3 & 3597426M2 Hitachi starters on above models. Replaces Lucas 26411, 27540. MF-3-102

3 ELECTRICAL Replacement parts to fit 1618050M4 3581576M3 New Lucas style starter assembly. Tractors: MF2640, MF2675, MF2705, MF3090, MF3505, MF3525, MF3545, MF3630, MF3650 (Lucas 27533, 26398). Starter, NEW, 10 tooth, 12-volt, clockwise, 2.8 KW. Tractors: MF3055, MF3075, MF3120, MF3120T, MF3140, MF3655, MF3660, MF3670, MF3690, MF3890, MF6170, MF6180, MF6270, MF6280, MF6290, MF8120, MF8140, MF8150, MF8160, MF8210, MF8220, MF8240, MF8250. Replaces 1447732R1, 3581576R1, 1446802M1, 3581576M1, 3930508R1, 3581576R01A, 3581576M3. 1751902M91 1750469M1 Starter Parts Starter drive housing. Fits 12-volt Delco starter 1107654. Tractors: TO35, MF35, F40, MF50, MF65. Industrials: 202, 204 (replaces Delco 1934316). Brush, services Delco 1109457. Tractors: TO20, TO30, TO35. 4 required. Starter Flywheel Ring Gears TP-RE41756 1049812M91 1035335M91 1019269M91 1025380M91 1036519M91 Starter Drives Drive assembly, services Auto-Lite starters. For Massey Harris. Tractors: 33, 44, 44K, 44-6, 55, 55K, 55D. Drive assembly, held on with keyway and set screws. Tractors: TO20, TO30, TO35. Services Delco starter 1109457, 1107654. Drive assembly, hole in middle. For gas engines. Tractors: MF35, MF50, MF65. Industrials: 202, 204, 302, 356. Services starter 1107226. Drive assembly. For Continental Z145. Tractors: MF135, MF150. Replaces Delco 1963808. Services starter 1108324. Drive assembly for Delco starters. Fits all MF diesel models; Perkins gas models. 1750034M1 731008M1 Flywheel ring gear. For Continental gas engine. Tractors: TO20, TO30, TO35, MF35, MF50, MF65, MF135, MF150, MF165, MF175, MF180. 145 teeth, 13-5/8" I.D. Flywheel ring gear. 115 teeth, 13-7/16" ID. For Perkins engine. Tractors: MF135, MF150, MF154S, MF165, MF168, MF174S, MF178, MF184, MF185, MF188, MF194, MF194F, MF230, MF235, MF240, MF245, MF250, MF253, MF255, MF265, MF275, MF283, MF285, MF290, MF333, MF340, MF350, MF355, MF360, MF362, MF365, MF374S, MF375, MF383, MF390, MF393, MF394S, MF398, MF3050, MF3060, MF3065, MF3070, MF3075, MF35, MF65, MF4225, MF4235, MF4240, MF4245, MF4255, MF4265, MF4325, MF4335, MF4345, MF4355, MF590, MF690, MF6120, MF6140, MF6150, MF6235, MF6245, MF6255, MF6265. Industrial Tractors: 20, 203, 205, 20C, 20D, 20E, 20F, 2135, 30, 302, 304, 30B, 30D, 30E, 30H, 3165, 356, 40, 40B, 40E, 50, 50C, 50D, 50E, 50H, 50H, 60H. Combines: 410. Replaces 0410236, 1500010, 3819719M1. 1755245M91 Drive assembly, heavy-duty replacement for 1036519M91. Fits all MF diesel models & Perkins gas models with Delco starter. MF-3-103

3 ELECTRICAL Battery Cables & Straps Voltage Regulators VR1816 Voltage regulators, 12 volt. Tractors: MH333D, MH444D using Delco generators 1118266, 1118306. 180142M92 Voltage regulator, 6-volt. Tractors: TO20, TO30, TO35. Tisco part number VR1814. Lengths shown are from terminal centers 180099M91 180165M91 180166M92 181572M91 Cable, starter switch to starter. Tractors: TO20, TO30. 16" long. Ground strap. Tractors: TE20, TO20, TO30, TO35. 5-1/2" long. Cable, battery to switch. Tractors: TE20, TO20, TO30; battery to ground for tractors: MF85, MF88 gas. 21" long. Cable, battery to solenoid. Tractors: TO35; battery to ground for tractors: MF35 gas, MF85D, MF88D, MF Super 90 gas. 14-1/2" long. Battery & Hood Hardware 182548M92 1031060M91 Voltage regulator, 12-volt. For models using generators. Tractors: TO35, MF25, F40, MF35, MF65, MF85, MF88, MF Super 90, MF135, MF150, MF165, MF175, MF180, MF202, MF204, MF203, MF205, MF2135, MF3165. Combines: SP300, SP410, SP510. Voltage regulator, 12-volt. For MF tractors using Delco alternators, replaces 1119507. Generator Cutout for Autolite CB4014 Generator cutout for Autolite, 6-volt. For most MH models to 1951. 180766M91 180654M1WN 180695M1WN Bolt with special wing nut, for hood latch assembly. Tractors: TO35..320" dia., 5.25" long. Bolt with wing nut, for hood latch assembly & battery tie rod. Tractors: MF35, MF50, MF135. 5/16"-24 x 5" overall. Battery tie bolt with wing nut. Tractors: MF35, MF50, MF135. 1/4"-20 x 10-3/4" overall. Generator Parts 1754877M91 Brush for 12-volt generator, 2 required 832960M3 Generator ball bearing, double-shielded, services newer 12-volt generators. MF-3-104

3 ELECTRICAL Replacement parts to fit Alternator Conversion Kit Alternators TO30ALT12V Updates older 6-volt tractors to 12-volt charging system. Kit includes rebuilt unicharge alternator with pulley, internal self-exciting regulator, 12-volt resistor, wiring harness, brackets, hardware, & instructions. Alternator conversion kit, for tractors less tach drive. Tractor: TO30. Uses alternator repair kit ARKSE7. Generic Alternators Sold outright - no cores to bother with. No deposit... No return. 1102920 Alternator, 63 amp., internal regulator. 3 terminal, 3 o'clock position. 1102921 ALT263SE 1103155 1103160 ALT280SE Alternator, 63 amp., internal regulator. 2 terminal, 3 o'clock position. Alternator, 63 amp unicharge one wire connection. Used in kit 5564-10300ALT. Alternator, 80 amp., internal regulator. 2 terminal, 3 o'clock position. Alternator, 80 amp., internal regulator. 3 terminal, 3 o'clock position. Alternator 80 amp unicharge one wire connection. 1100883 Alternator, 61 amp., uses external regulator, comes with pulley. For most MF Tractors 1965 & later. Replaces 52 amp 92052. Sold outright only, no core charge. Uses alternator repair kit ARK-1. 1100583 50061-E 3933142M91 3405390M1 Alternator, 42 amp., internal regulator. 2 terminal 3 o clock position. Exchange alternator. Tractors: MF135, MF150, MF1100, MF1130. Industrials: 20, 30, 40, 50 using Delco 1100791. Services new 518880M91 & 508545M91, 40 amp. Pulley included. Use alternator repair kit ARK-1. Alternator, NEW, 55 amp, 12 volt, clockwise. Tractors: MF154, MF184, MF194, MF194-4, MF240, MF243, MF245, MF250, MF253, MF255, MF300, MF350, MF360, MF364, MF365, MF373, MF374, MF375, MF377, MF383, MF384, MF387, MF390, MF390T, MF393, MF396, MF397, MF398, MF399, MF699. Replaces 1897695M91, 3714922M1. New alternator assembly, 65 amp. Tractors: MF240, MF250, MF253, MF270, MF283, MF290, MF298, MF360, MF364S, MF374S, MF375, MF383, MF384S, MF390, MF390T, MF393, MF394S, MF398, MF399, MF670, MF690, MF698, MF699. Industrials: MF20D, MF20E, MF20F, MF30E, MF30H, MF40E, MF50E. Replaces: 1643314M91, 1676689M92, 1676690M92, 1691794M92, 1895398M91, 1897264M91, 1897695M91, 3698016M91, (Lucas 24087, 24124). MF-3-105

3 ELECTRICAL 3714944M1 Alternator, New, 70 amp, 12 volt, clockwise. Tractor: MF6110, MF6120, MF6130, MF6140, MF6160, MF6170, MF6180, MF6235, MF6245, MF6255, MF6265, MF6270, MF6280, MF6290. Replaces 3701-911-M91, 3714-922-M, 3714-944-M. Internal Voltage Regulator For Alternators AP3158 Alternator Pulleys Pulley, 3-1/8" dia., 5/8" shaft bore, 2 grooves for 1/2" wide v-belt. Use with alternator ALT-15105. Alternator Repair Parts 1052023M91 Internal voltage regulator for MF/Delco alternators. Tractors: MF230, MF235, MF245, MF255, MF265, MF275, MF285, MF1085, MF1105, MF1135, MF1155, MF1500, MF1505, MF1800, MF1805, MF2675, MF2705, MF2745, MF2775, MF2805. Industrials: 20C, 30B, 30D, 40B, 50C. Replaces 1039664M1 & Delco 1116387. Services Alternators: DELCO MF DELCO MF 1100578 528352M91 1102920 579541M91 1100583 530440M92 1102921 588421M91 1100585 536378M91 1103116 579881M91 1100588 579130M91 1103117 579880M91 1100589 528353M91 1103133 3320296M91 *1891055 & 1891055HD are not interchangeable. Fuse Holders 907998 1974862 1971528 1891055 1891055HD BHK1 Bearing, alternator front. Bearing, alternator rear. Diode trio, Delco alternator. Rectifier assembly, Delco alternator. Cannot be replaced by 1891055HD Rectifier assembly, Delco alternator. Will not replace 1891055 Brush holder kit, alternator. 522462M91 526601M91 Fuse holder, chassis mount with threads for securing nut. Tractors: 135, 150, 165, 175, 180, 230, 235, 245, 255, 265, 275, 285. Industrials: 20, 30, 40, 31, 20C, 30B, 40B, 50C, 3165. Replaces 506063M91. Fuse holder, in line assembly. Tractors: 150, 165, 175. Industrials: 30, 31, 40. BHK2 515521M91 AMG60 Brush holder kit, alternator (HD brush holder & brushes) Ammeter Assembly Ammeter gauge. For all TO & MF models using 30-0-30 amperes, non-luminous. For 2" dia. hole. Ammeter gauge has 60-0-60 range, non-luminous, fits 2" dia. hole, stainless bezel, black background, white letters, & white pointer. 230246 1628494M1 Fuse holder, less fuse. 20 amp, fits ½" hole. Tractors: MF135, MF150, MF165, MF175, MF180, MF230, MF235, MF245, MF255, MF265, MF275, MF285. Industrial: 20, 20C, 30, 30B, 31, 40, 40B, 50C, 2135, 2200, 2500, 3165. Vintage Iron Halogen Bulb Halogen bulb 12-volt, 55 watt (L4970). MF-3-106

3 ELECTRICAL Replacement parts to fit Sealed Beam Bulbs Taillight Assemblies 1752311M91 Light Ring. Retained to headlight with 2 screws. Grey primer with ground wire. Tractors: TO20, TE20, TEA20, TO30, TO35, MF40, MF50, MH50, MF65, MF85, MF88, Super 90. Vintage Iron 1002802M91 1002803M91 1752866M91 505285M1 1038428M91 535505M1 285871M1 H7609 L4511 L4019 L4411 Sealed beam bulb 6-volt. Tractors: TE20, TO20, TO30, TO35 (L4019). Sealed beam bulb 12-volt. Tractors: TE20, TO20, TO30, TO35 (early hood mount), MH50, MF50, MF65. Replaces 1751347M91 (L4419). Sealed beam bulb 12-volt. Early fender mount models. Tractors: TO35, MH50, MF50, MF65. Inner or upper fender mount models. Tractors: MF150, MF165, MF175, MF180, MF1100, MF1130 (L4411). Sealed beam bulb 12-volt. Outer flat fenders tractor: MF135; Outer or lower fender all late MF tractors, 12-volt (L4406). Sealed beam bulb, 12-volt. Tractors: MF35, MF50, MF65 (L4419). Sealed beam bulb. Tractors: MF235, 255, 265, 275, 285. 12-volt (L44401), 3 spade terminals. 12-volt, halogen sealed beam bulb. 4-1/2" dia. screw terminals (H7606). Halogen sealed beam bulb. 4-1/2" dia., 5, 200 candle power. Trapezoidal light pattern. Can be used in place of L4427. 6-volt sealed beam bulb, 4-1/2" dia. 6-volt sealed beam bulb, 5-3/4" dia. 12-volt sealed beam bulb, 4-1/2" dia. 45645HA 1751823M91 371461R2 537328R1 Round red tail light assembly with license lamp window. 4-1/2" diameter -- 1 7/8" c-c mounting stud. Vintage Iron Taillight assembly. Includes 12-volt bulb & mounting bolts. Painted black. Solid bucket 1-3/4" c-c mounting studs. Tractors: TE20, TO20, TO30, TO35, MF35, MF40, MF50, MH50, MF65, MF85, MF90, MF135. Industrials: 202, 203, 204, 205. Vintage Iron Sealed-beam combination rear light bulb, 12-volt. 4-1/2" diameter sealed beam combo light bulb (used with small separate bulb). Vintage Iron Warning Light Rectangular fender and cab mount warning light One red and one amber lens with amber side marker, black ABS mount --- Single contact bulbs #57 (small) & #1156 (large) 12 Volt --- 4.5" wide, 1/2" diameter stud. Serviceable for models with rectangular warning lights. Vintage Iron L4509 12-volt sealed beam bulb, 4-1/2" dia. L4419 12-volt sealed beam bulb, 5-3/4" dia. L1133 6-volt bulb, flood. 677540 12-volt warning light, mounts on fender or cab. Two 4" amber lenses. L1157 12-volt bulb, replacement bulb for 677540. MF-3-107

4 POWER TRAIN Brake Shoes Brake Cylinders 3595504M2 Brake cylinder, Master assembly. Tractors: MF360 (to engine s/n V39466), MF375 (to engine s/n V39466), MF383 (to engine s/n V39466), MF390 (to engine s/n V39466), MF398 (to engine s/n V39466), MF399 (to engine s/n V39466). 830537M93AF 830480M93AF 1810517M91 Kit, 4 shoes with linings bonded. 2" x 15" total shoe length. Tractors: TO20, TO30. Two wheel set. Kit, 4 shoes with linings bonded. 2" x 19-1/2" total shoe length. Tractors: TO35, MF35, F40, MF50, MF135, MF150, MF230, MF235 (std. & orch.), MF245. Two wheel set. Kit, 2 shoes with linings. 2" wide. Priced and sold per pair. Tractors: MF231, MF240. One wheel set. Brake Drum 3596785M92 3477380M93 Brake cylinder, Master assembly. Tractors: MF360 (engine s/n V39466 & up), MF362, MF375 (engine s/n V39467 & up), MF383 engine s/n 39466 & up), MF390 (engine s/n V39466 & up), MF390T (engine s/n V39466 & up), MF398 (engine s/n V39466 & up), MF399 (engine s/n V39466 & up). Brake cylinder, Slave assembly (LH). Tractors: MF360, MF362, MF375, MF383, MF390, MF390T, MF393, MF396, MF398, MF399. 1682767M1 Brake cylinder, Master assembly. Tractors: MF690 (w/small double reservoir), MF698 (w/small double reservoir), MF698T, MF699. 827707M5 Brake drum. Tractors: TO35, MF35, F40, MH50, MF50, MF135 (except orchard), MF150, MF230, MF235 (except orchard), MF240, MF245 (except orchard). Industrials: 20, 20C, 20D, 30 turf, 35, 40, 202, 204, 2135, 2200, 3165. Replaces 181230M1. 1676387M92 3383079M5 Brake Cylinder, Slave assembly. Tractors: MF270, MF290, MF298, MF670, MF690, MF698, MF698T, MF699. Industrials: 24 Telescopic handler, 25 Telescopic handler, 30E, 30H, 40E, 50E, 50E, 50H, 60H. Master brake cylinder assembly. 2 used per tractor. Tractors: MF3050, MF3065, MF3070, MF3075, MF3090, MF3095, MF3120T, MF3125, MF3645, MF3655, MF3670, MF3690, MF6150, MF6170, MF6180, MF8120, MF8140, MF8150, MF8160. Replaces 1810833M91. 3614780M91 Master brake cylinder assembly (3 ports) (Dia. 0.625 ). Tractors: MF362, MF365, MF375, MF383, MF390, MF390T, MF393, MF396, MF398, MF399. MF-4-108

4 POWER TRAIN Replacement parts to fit 1874957M91 3477381M93 3477380M93 Master brake cylinder assembly. (Dia. 0.625 ). Tractors: MF1134, MF1024, MF274SK, MF294S, MF560, MF565, MF575, MF590, MF592, MF595, MF690, MF698; Combine Series: MF660, MF830, MF835, MF810. Brake cylinder, Slave assembly (RH). Tractors: MF360, MF362, MF375, MF383, MF390, MF390T, MF393, MF396, MF398, MF399. Brake cylinder, Slave assembly (LH). Tractors: MF360, MF362, MF375, MF383, MF390, MF390T, MF393, MF396, MF398, MF399. Brake Actuators 1021314M92AF 1044526M1AF Brake Discs Measure disc diameter before ordering. Some models have optional disc. Order 1021314M92, 7-1/8" dia. for malleable axles. 1044526M1, 8-7/8" dia. for cast axles. Brake disc, 7-1/8" x 4", 27 splines. Tractors: MF65, MF85, MF88, MF90 Super, MF135, MF150, MF165, MF175, MF180. Industrials: 30, 31, 40, 50, 203, 205, 302, 304, 3165. Tractor Shovel: 356. Forklift: 2500. Replaces 1753117M1. Brake disc, 8-7/8" x 6", 27 spline. Tractors: MF135, MF165, MF175, MF180, MF235, MF255, MF265, MF275, MF285, MF1080, MF1085. Industrials: 30, 31, 40. Replaces 1805980M1. 3596778M91 3596776M91 Brake actuator assembly (RH side). Tractors: MF360 (w/tangential brakes), MF362, MF365, MF375 (w/tangential brakes), MF390 (w/tangential brakes), MF390T (w/tangential brakes), MF393, MF396, MF398 (w/tangential brakes), MF399, MF4225, MF4235, MF4243, MF4245, MF4253, MF4255, MF4260, MF4263, MF4270, MF4325, MF4335, MF4345, MF4355, MF4360, MF4370. Brake actuator assembly (LH side). Tractors: MF360 (w/tangential brakes), MF362, MF365, MF375 (w/tangential brakes), MF390 (w/tangential brakes), MF390T (w/tangential brakes), MF393, MF396, MF398 (w/tangential brakes), MF399, MF4225, MF4235, MF4243, MF4245, MF4253, MF4255, MF4260, MF4263, MF4270, MF4325, MF4335, MF4345, MF4355, MF4360, MF4370. 1860964M2 1860965M2 Friction disc, used in wet disc brake system. 8-1/2" O.D.,.190" thick. OEM quality, appearance & performance. Tractors: MF245, MF250, MF255, MF265, MF275, MF285, MF1085. Industrials: 11 wheel loader UK, 30B, 30D, 31, 40, 40B, 50A, 50C, 50D, 60 backhoe/loader. Forklifts: 4500, 6500. Sugar Harvesters: 102, 201. Intermediate steel disc, used in wet disc brake system. OEM quality, appearance & performance. Tractors: MF245, MF250, MF255, MF265, MF275, MF285, MF1085. Industrials: 11 wheel loader UK, 30B, 30D, 31, 40, 40B, 50A, 50C, 50D, 60 backhoe/loader. Forklifts: 4500, 6500. Sugar Harvesters: 102, 201. Brake Disc Actuating Balls 16779 Steel ball, brake actuating, 7/8" diameter. 16780 Steel ball, brake actuating, 1" diameter. MF-4-109

4 POWER TRAIN 1853148M1 1005510M1 183462M1 Disc Brake Parts Spring, actuator disc return for disc brakes. Tractors: MF154-4, MF184-4, MF235 orchard, MF240, MF245, MF250, MF253, MF255, MF265, MF270, MF275, MF282, MF283, MF285, MF290, MF298, MF360, (prior to s/n V39466), MF375 (prior to s/n V39466), MF383 (prior to s/n V39466), MF390 (prior to s/n V39466), MF398 (prior to s/n V39466), MF399 (prior to s/n V39466), MF670, MF690, MF698, MF699. Industrials: 30B, 30D, 30E, 40B, 40E, 50C, 50D, 50E, 50F. Forklift: 4500, 6500. For tractors with cast iron axle: MF135, MF165, MF175, MF180. Industrials: 30, 31, 40, 50A. Spring, actuator disc return for disc brakes. 3 used in each actuator. Tractors: MF65, MF85, MF88, MFSuper90, MF95, MF97, MF150, MF154S, MF174S, MF254-4, MF274-4, MF294-4, MF333, MF444. Industrials: 50, 203, 205, 302, 304, 356 tractor shovel, 3165. Forklift: 2500. Tractors with malleable iron axle: MF135, MF165, MF175, MF180, MF1080. Industrials: 30, 31, 40. Seal, for brake pull rod, dry disc brakes. Tractors: MF65, MF85, MF88, MF90, MF135 (orchard with malleable iron axle), MF150, MF154-4, MF154-4S, MF165 (with malleable iron axle), MF174-4S, MF175 (with malleable iron axle), MF180 (with malleable iron axle), MF184-4, MF254-4, MF274-4, MF285, MF294-4, MF1080, MF 1085. Industrials: 30 (with malleable iron axle), 31 (with malleable iron axle), 40 (with malleable iron axle), 50, 203, 205, 302, 304, 3165. 184334M1 1860959M1 Rod & clevis, 6-1/4" from end of rod to hole center. Disc brake lever to actuating links, except models with cast axle housings. Tractors: MF65, MF135, MF150, MF165, MF175, MF180, MF1080. Industrials: 30, 40, 50, 203, 205, 302, 304, 3165. Forklift: 2500 Seal, for brake pull rod, wet disc brakes. Fits into left & right lever brackets. Tractors: MF154-4S, MF174-4S, MF194-4, MF194-4F, MF245, MF250, MF253, MF254-4, MF255, MF265, MF270, MF274-4, MF275, MF282, MF283, MF285, MF290, MF294-4, MF298, MF670, MF690, MF698, MF699, MF1085. Industrials: 30D, 30E, 40E, 50D, 50E. Replaces 1667175M1. Brake Cable Assemblies 1689024M93 Hand brake cable (RH) 49-1/2" length. Tractors: All 2WD; MF231S, MF240, MF241, MF243, MF253, MF263. 1689025M94 3698735M91 3698736M91 3595762M91 3595763M91 Hand brake cable (LH) 62" length. Tractors: All 2WD; MF231S, MF240, MF241, MF243, MF253, MF263. Hand brake cable (RH) 49" length. Tractors: MF240 (2WD w/wet brakes; s/n A20286 & up), MF240 (4WD; s/n A20286 & up), MF243 (4WD), MF253 (4WD), MF263 (4WD). Hand brake cable (LH) 60" length. Tractors: MF240 (2WD, w/wet brakes; s/n A20286 & up), MF240 (4WD; s/n A20286 & up), MF243 (4WD), MF253 (4WD), MF263 (4WD). Hand brake cable (RH) 49". For tractors with Concentric brakes W/O spacer. Tractors: MF360, MF375, MF383, MF390, MF398 (all to engine s/n V39465). Hand brake cable (LH) 60". For tractors with Concentric brakes W/O spacer. Tractors: MF360, MF375, MF383, MF390, MF398 (all to engine s/n V39465). MF-4-110

4 POWER TRAIN Replacement parts to fit 1696648M91 1696649M91 3596774M92 3596775M92 3596772M92 3596773M92 Hand brake cable (RH) 44". For tractors with concentric brakes with spacer. Tractors: MF360, MF375, MF390, MF398, MF399 (all to engine s/n V39465). Hand brake cable (LH) 55". For tractors with concentric brakes with spacer. Tractors: MF360, MF375, MF390, MF398, MF399 (all to engine s/n V39465). Hand brake cable (RH) 52". For tractors with Tangential brakes W/O spacer. Tractors: MF360, MF362, MF365, MF375, MF383, MF390, MF390T, MF393, MF396, MF398, MF399. Hand brake cable (LH) 62-1/2". For tractors with Tangential brakes W/O spacer. Tractors: MF360, MF362, MF365, MF375, MF383, MF390, MF390T, MF393, MF396, MF398, MF399. Hand brake cable (RH) 46". For tractors with Tangential brakes with spacer. Tractors: MF362, MF365, MF375, MF383, MF390, MF390T, MF393, MF396, MF398, MF399. Hand brake cable (LH) 57". For tractors with Tangential brakes with spacer. Tractors: MF362, MF365, MF375, MF383, MF390, MF390T, MF393, MF396, MF398, MF399. Clutch Kit 185923M91 513574M91 3610268M91 3281105M91 Clutch Cover Assemblies For Single Clutch Pressure plate assembly, NEW. 9" SINGLE CLUTCH, 6 SPRINGS. Tractors: TO20, TO30, TO35, MF25, MF35, MF50, MH50, MF202, MF204. Replaces 183209M91, 18355M91. Clutch cover assembly, 11", 10-spline plate, 1-3/4" hub. For split torque single clutch. Tractors: MF165, MF175, MF180. Clutch Cover Assemblies For Dual Clutch Dual clutch assembly, 12" with 10", 25-spline PTO disc. Supplied same as OEM, less 12" disc 3599462M92, order separately if needed. Tractors: MF275, MF282, MF283 (except Brazil), MF290, MF383, MF390. Replaces 1868005M92. For replacement PTO disc use 347835. * Pressure plate with PTO disc only. Order bearings and engine disc separately. Pressure Plates Clutch Pressure Plate Assembly, 8", diaphragm style. Tractors: MF205, MF205-4, MF1020. 1808749M94K Clutch kit, for 12" split torque clutch. Kit contains remanufactured pressure plate assembly 12", 12 springs, 1-5/8" hub, 25 spline; NEW disc, H.D. 12", woven lining, 1-1/8" hub. 10 spline; new release & pilot bearings. Tractors: MF285, MF1085. 3701015M92 Pressure Plate Assembly, 13", 25 spline 1.5" hub. Tractors: MF375, MF390, MF390T, MF393, MF394S, MF396, MF398, MF399, MF4243, MF4245, MF4253, MF4255, MF4260, MF4263, MF4265, MF4270, MF4345, MF4355, MF4360, MF4370. Used in TISCO kit 3701015M92KT. MF-4-111

4 POWER TRAIN Clutch Discs For Single and Dual Clutches 180241M91AF Clutch disc, 9", 10-spline, 1-3/8" hub spring loaded with woven heavy-duty lining. For single clutch. Tractors: TO20, TO30. 181114M91 3478359M91 513580M91 3599462M92 3610274M92 Clutch disc, 9", 10-spline, 1-1/8" hub, no damper springs, organic lining. For single clutch. Tractors: TO35, MF35, MH50, MF50, MF135. Clutch disc, 10", 25-spline. For live PTO. For dual clutch 3610268M91 or 1868005M92. Tractors: MF275, MF282, MF283 (except Brazil), MF290, MF383, MF390. For other dual clutches. Tractors: MF 250, MF270, MF375. Industrials: 20D (with HD clutch), 40E. Replaces 1865836M91. Clutch disc, 11", 10-spline, 1-1/8" hub, damper springs, organic lining. For split torque single clutch. Tractors: MF165, MF175, MF180, MF255, MF265. Clutch disc, standard, 12", 10 spline, 1-1/8" hub, with damper springs, organic linig. For split torque single clutch. Tractors: MF240, (s/n 2773N01001 & up), MF270, MF275, MF290, MF670, MF690. For dual clutch. Tractors: MF231, MF240, MF250, MF253, MF270, MF275, MF282, MF283 (except Brazil), MF290. Industrial: 20D. Replaces 887889M94, 1866042M93. Clutch disc, 12", 21 spline, 1-1/8" hub, no damper springs, organic lining. For split torque single clutch. Tractors: MF360, MF362, MF390. For dual clutch. Tractors: MF390. Replaces 1693884M91. 526666M91KT 532319M91KT 3701015M92KT 526665M91KT Double Clutch Kit Assemblies Double clutch kit assembly "NEW" 11" PP with 1.5" hub 10 spline PTO disc. Includes 11" Rigid Clutch Disc, 10 spline.933" hub, New release & pilot bearing with clutch alignment tool. Tractors: F40, MH50, MF135, MF150; MF35, TO35 (late production). Industrials: 20, 2135, 2200, 40. Double clutch kit assembly "NEW" 11" PP with 1.5" hub 25 spline PTO disc. Includes 11" Rigid Clutch Disc, 10 spline.933" hub, New release & pilot bearing with clutch alignment tool. Tractors: MF135, MF150, MF165, MF175, MF175 U.K., MF178 U.K., MF180, MF230, MF235, MF245, MF255, MF265, MF35, MH50, MF65, TO35. Industrials: 20, 20C, 2135, 30, 3165. Split Torgue clutch kit assembly "NEW" 13" PP with 1.5" hub 25 spline. Includes 12.5" 5 PAD Disc, 21 spline 1.00" hub, New release & pilot bearing. Contains clutch alignment tool. Tractors: MF375, MF390, MF390T, MF393, MF394S, MF396, MF398, MF399, MF4243, MF4245, MF4253, MF4255, MF4260, MF4263, MF4265, MF4270, MF4345, MF4355, MF4360, MF4370. Double clutch kit assembly, Medium spring, "NEW" 11" PP 1.5" hub 10 spline PTO disc, Includes 11" Rigid clutch Disc, 10 spline.933" hub, New release & pilot bearing with clutch alignment tool. Tractors: MF135, MF150, MF165, MF175, MF175 U.K., MF178 U.K., MF180, MF235, MF245, MF255, MF265, MF35, MH50, MF65, TO35. Industrials: 20, 20C, 2135, 30, 3165. MF-4-112

4 POWER TRAIN Replacement parts to fit 3599463M92KT 3599463M94KT 532320M91KT 532321M91KT Double clutch kit assembly, "NEW" 12" PP 25 spline PTO disc, Includes 12" Rigid clutch Disc, 21 spline.987" hub, New release & pilot bearing. Contains clutch alignment tool. Tractors: MF231, MF240P, MF240S, MF253, MF261, MF263, MF265S, MF271, MF281, MF285S, MF360, MF362, MF365, MF375, MF383, MF390, MF390T. Industrials: 20D, 20F, 30E, 40E. Double clutch kit assembly, "NEW" 12" PP 25 spline PTO disc, light-duty springs. Includes 12" Rigid clutch Disc, 10 spline 1-1/8" hub, New release & pilot bearing with clutch alignment tool. Tractors: MF165, MF175, MF175 U.K., MF178 U.K., MF231, MF240P, MF240S, MF253, MF261, MF263, MF270, MF271, MF275, MF281, MF282, MF283, MF285, MF290 U.K, MF670, MF690. Industrials: 20D, 20E, 20F, 30E, 40E. Double clutch kit assembly, "NEW" 11" PP 1.025" hub, 25 spline PTO disc, Includes 11" Rigid clutch Disc, 10 spline.933" hub, New release & pilot bearing with clutch alignment tool. Tractors: MF135, MF150, MF165, MF175, MF175 U.K., MF178 U.K., MF180, MF235, MF245, MF255, MF265, MF35, MH50, MF65, TO35. Industrials: 20C, 2135, 30, 30B, 30D, 3165, 40B. Double clutch kit assembly, Heavy duty "NEW" 11" PP 1.625" hub, 25 spline PTO disc, Includes 11" Rigid clutch Disc, 10 spline.933" hub, New release & pilot bearing with clutch alignment tool. Tractors: MF175, MF175 U.K., MF178 U.K., MF255, MF265. 3610268M91KT AG08TOOL AG09TOOL AG10TOOL 886396M1 Double clutch kit assembly, "NEW" 12" PP 1.625" hub, 25 spline PTO disc, heavy-duty springs. Includes 12" Rigid clutch Disc, 10 spline 1-1/8" hub, New release & pilot bearing with clutch alignment tool. Tractors: MF165, MF175, MF175 U.K., MF178 U.K., MF231, MF240P, MF240S, MF253, MF261, MF263, MF265S, MF270, MF271, MF271, MF271E, MF275, MF281, MF281, MF281E, MF282, MF283, MF285, MF285S, MF383, MF390, MF471, MF481, MF670, MF690. Industrials: 20D, 20E. Clutch Alignment Tools Clutch Alignment tool, For dual stage type w/1-1/8 10 spline and 1-3/4 10 spline. For 526665M91 KT, 526666M91KT. Clutch Alignment tool, For Dual Stage, 1-1/8 21 splines, 1-5/8 25 splines. For 3599463M92KT, 3701015M92KT. Clutch Alignment tool, For Dual stage type w/1-1/8 10 splines and 1-5/8 25 splines. For 3599463M94KT, 3610268M91KT, 532319M91KT, 532320M91KT, 532321M91KT. Clutch Cover Repair Parts Clutch spring, red, 2 13/16" long. For pressure plate in single & dual clutch assemblies. Tractors: MF231, MF240, MF250, MF270, MF275, MF282, MF283 (except Brazil), MF290, MF383, MF390, MF670, MF690. Industrials: 20D, 30E, 40E, 50E. Replaces spring 1753745M1, lavender 2-7/16" long, in dual clutches using pressure plate 1031853M1, must replace all springs. Tractors: MF65, MF165, MF175, MF255, MF265. Industrials: 30, 3165. MF-4-113

4 POWER TRAIN 1753751M2 1853164M1 3534301 887898M1 Insulating washer, for pressure plate spring. For dual clutch. Tractors: TO35, MF35, MF50, MF65, MF135, MF150, MF165, MF175, MF180, MF230, MF231, MF235, MF240, MF245, MF250, MF253, MF255, MF265, MF270, MF275, MF282, MF283 except Brazil, MF290, MF360, MF362, MF375, MF383, MF390. Industrials: 20, 20C, 20D, 30, 30B, 30D, 31, 40, 40B, 40E. For split torque single clutch. Tractors: MF240, MF270, MF275, MF290, MF298, MF360, MF362, MF375, MF390, MF393, MF398, MF399, MF670, MF690, MF698, MF699. Industrials: 30E, 40E, 50E. Replaces 3478361M91. Adjusting bolt, 3/8" x 25/32" NF, for clutch release lever. For dual clutch. Tractors: TO35, MF35, MF50, MF65, MF135, MF150, MF165, MF175, MF180, MF230, MF231, MF235, MF240, MF245, MF250, MF253, MF255, MF265, MF270, MF275, MF282, MF283 (except Brazil), MF290, MF360, MF362, MF375, MF383, MF390. Industrials: 20, 20C, 20D, 30, 30B, 30D, 31, 40, 40B, 40E. For split torque single clutch. Tractors: MF240, MF270, MF275, MF290, MF298, MF360, MF362, MF375, MF390, MF393, MF398, MF399, MF670, MF690, MF698, MF699. Industrials: 30E, 40E, 50E. Replaces 1753954M1. Use with clutch release levers 887898M1 & 1754681M2. Lock nut, 3/8" NF, for clutch release lever adjusting bolt. Use with 1853164M1 on same applications. Clutch release lever, for split torque single clutch or dual clutch. Tractors: MF231, MF240, MF250, MF253, MF270, MF275, MF282, MF283 (except Brazil), MF290, MF298, MF383, MF390, MF398, MF399, MF670, MF690, MF698, MF699. Industrials: 20D, 30E, 40E, 50E. Replaces 1810817M91. 887910M1 891826M1 891827M1 1753965M2 887894M1 887893M1 Torsion spring for clutch release lever. For split torque single clutch or dual clutch. Tractors: MF231, MF240, MF250, MF253, MF270, MF275, MF282, MF283 (except Brazil), MF290, MF298, MF383, MF390, MF398, MF399, MF670, MF690, MF698, MF699. Industrials: 20D, 30E, 40E, 50E. Pivot pin, for clutch cover release lever to cover..30" dia., 2.68" L. Tractors: MF240, MF250, MF253, MF270, MF275, MF282, MF283 (except Brazil), MF290, MF298, MF383, MF390, MF398, MF399, MF690, MF698, MF699. Industrials: 20D, 30E, 35, 50E. Also used as an alternate on clutch covers manufactured in the United Kingdom. Tractors: MF35, MF50, MF65. Industrial: 20. Hair pin, use with pivot pin 891826M1 on same applications. Clevis pin, 5/16" x 7/8", clutch release lever to link. For dual clutch. Tractors: TO35, MF35, MF50, MF65, MF135, MF150, MF165, MF175, MF180, MF230, MF235, MF245, MF255, MF265. Industrials: 20, 20C, 30, 30B, 30D, 31, 40, 40B, 202, 203, 302, 304, 2135, 3165. Link, clutch release lever to pressure plate. For split torque single clutch or dual clutch. Tractors: MF231, MF240, MF250, MF253, MF270, MF275, MF282, MF283 (except Brazil), MF290, MF298, MF383, MF390, MF398, MF399, MF670, MF690, MF698, MF699. Industrials: 20D, 30E, 40E, 50E. Replaces 1810815M91. Clevis pin, 5/16" x 1-1/2", clutch release lever link to pressure plate. For split torque single clutch or dual clutch. Tractors: MF231, MF240, MF250, MF253, MF270, MF275, MF282, MF283 (except Brazil), MF290, MF298, MF383, MF390, MF398, MF399, MF670. MF-4-114

4 POWER TRAIN Replacement parts to fit Dual Clutch Assemblies & Components Assembly 1 includes itmes 2 thru 11 only. Items A, B, 12 must be ordered separately. Application Tractors: TO35 (to s/n 177394 & s/n 177520 to 177537), F40, MH50 (to s/n 536199, early production), MF35 Complete Assembly 1 Tractors: TO35, MF35 (late production), 526666M91 MF50. Industrial Tractors: 20, 40 (w/10 spline PTO disc) Industrial Tractors: 20, 20C (w/25 spline PTO 532319M91 disc) Industrial Tractors: 20C (except Turf), 30, 532320M91 30B, 30D, 40B (w/25 spline PTO disc) Tractors: MF65. Industrial Tractors: 30 (w/10 526665M91 spline PTO disc) Tractors: MF135, MF150 (w/10 spline PTO 526666M91 disc) Tractors: MF135, MF150 (w/25 spline PTO 532319M91 disc) Tractors: MF165 (w/10 spline PTO disc) 526665M91 Tractors: MF165 (w/25 spline PTO disc) 532320M91 Tractors: MF175, MF180 (w/10 spline PTO 526664M91 disc) Tractors: MF175 (w/25 spline PTO disc) 532321M91 Tractors: MF230 (w/25 spline PTO disc) 532319M91 Tractors: MF235, MF245 (except Orchard) 532320M91 (w/25 spline PTO disc) Tractors: MF255 early production (w/25 spline 532320M91 PTO disc) Tractors MF255 late production (w/25 spline 532321M91 PTO disc) Tractors: MF265 (w/25 spline PTO disc) 532321M91 Tractors: MF270 (w/25 spline PTO disc) Tractors MF275, MF282, MF283 (except 3610268M91 Brazil), MF290, MF383, MF390 (w/25 spline PTO disc) Tension Spring 2 893121M2 893121M2 893121M2 893121M2 893121M2 893121M2 893121M2 893121M2 893121M2 893121M2 893121M2 893121M2 893121M2 893121M2 893121M2 887910M1 887910M1 Release Lever 3 899818M2 899818M2 899818M2 899818M2 899818M2 899818M2 899818M2 899818M2 899818M2 899818M2 899818M2 899818M2 899818M2 899818M2 899818M2 887898M1 887898M1 Lever Pin 4 1753752M2 1753752M2 1753752M2 1753752M2 1753752M2 1753752M2 1753752M2 1753752M2 1753752M2 1753752M2 1753752M2 1753752M2 1753752M2 1753752M2 1753752M2 891826M1 891826M1 PTO Clutch Disc 7 3620411M91 3620411M91 1043282M92 1043282M92 3620411M91 3620411M91 1043282M92 3620411M91 1043282M92 3620411M91 1043282M92 1043282M92 1043282M92 1043282M92 1043282M92 1043282M92 3478359M91 3478359M91 MF-4-115

4 POWER TRAIN Dual Clutch Assemblies & Components Assembly 1 includes itmes 2 thru 11 only. Items A, B, 12 must be ordered separately. Application Flywheel Plate 8 Tractors: TO35 (to s/n 177394 & s/n 177520 to 177537), F40, MH50 (to s/n 536199, early production), MF35 Tractors: TO35, MF35 (late production), MF50. 1040886M1 Industrial Tractors: 20, 40 (w/10 spline PTO disc) Industrial Tractors: 20, 20C (w/25 spline PTO 1040886M1 disc) Industrial Tractors: 20C (except Turf), 30, 30B, 1040886M1 30D, 40B (w/25 spline PTO disc) Tractors: MF65. Industrial Tractors: 30 (w/10 1040886M1 spline PTO disc) Tractors: MF135, MF150 (w/10 spline PTO disc) 1040886M1 Tractors: MF135, MF150 (w/25 spline PTO disc) 1040886M1 Tractors: MF165 (w/10 spline PTO disc) 1040886M1 Tractors: MF165 (w/25 spline PTO disc) 1040886M1 Tractors: MF175, MF180 (w/10 spline PTO disc) 1040886M1 Tractors: MF175 (w/25 spline PTO disc) 1040886M1 Tractors: MF230 (w/25 spline PTO disc) 1040886M1 Tractors: MF235, MF245 (except Orchard) (w/25 1040886M1 spline PTO disc) Tractors: MF255 early production (w/25 spline 1040886M1 PTO disc) Tractors MF255 late production (w/25 spline PTO 1040886M1 disc) Tractors: MF265 (w/25 spline PTO disc) 1040886M1 Tractors: MF270 (w/25 spline PTO disc) Tractors MF275, MF282, MF283 (except Brazil), MF290, MF383, MF390 (w/25 spline PTO disc) Clutch Spring 9 Lever Link 10 1031854M1 1031854M1 1031854M1 1031854M1 1031854M1 1031854M1 1031854M1 1031854M1 1031854M1 1031854M1 1031854M1 1031854M1 1031854M1 1031854M1 1031854M1 886396M1 887894M1 886396M1 887894M1 Pressure Plate 11 1040884M1 1040884M1 1040884M1 1040884M1 1040884M1 1040884M1 1040884M1 1040884M1 1040884M1 1040884M1 1040884M1 1040884M1 1040884M1 1040884M1 1040884M1 Clutch Disc 12 182841M92 516068M93 516068M93 516068M93 516068M93 516068M93 516068M93 516068M93 516068M93 516068M93 516068M93 516068M93 516068M93 516068M93 516068M93 516068M93 3599462M92 MF-4-116

4 POWER TRAIN Replacement parts to fit Clutch Pilot Bearings Clutch Release Bearings 832960M3 832953M3 828123M2 886727M4 183129M2 Clutch pilot bearing. 0.670" ID, 1.574" OD, 0.470" width. Tractors: TE20, TO20, TO30, F40, MF35, MH50, MF50, MF65 (except diesel), MF85D, MF Super 90, MF135, MF150, MF165, MF175, MF180, MF235, MF255, MF265, MF275. Clutch pilot bearing, heavy-duty, long lasting stainless steel. 0.670" ID, 1.574" OD, 0.470" width. Tractors: MF50, MF65, MF85, MF88, MF235, MF245, MF255, MF285, MF1080; industrials: 20, 20C, 30, 30B, 31, 35 utility & turf, 40, 40B, 50, 50A, 50C, 202, 203, 204, 205, 302, 304, 2135, 2200, 3165. Skidder: 320. Forklifts: 2500, 4500, 6500. Clutch pilot bearing. 0.670" ID, 1.574" OD, 0.470" width. Tractors: MF240, MF250, MF253, MF270, MF282, MF283 (except Brazil), MF360, MF362, MF375, MF383, MF390, MF393, MF398, MF399, MF670, MF690, MF698, MF699. Industrials: 20D, 30E, 40E, 50E. Replaces 29963. Carriers For Clutch Release Bearings Carrier for clutch release bearing. Carrier bore 2.228" (2-1/4" approx.); O.D. 2-1/2". Tractors: MF231, MF240, MF250, MF253, MF270, MF282, MF283, MF290, MF298, MF360, MF362, MF375, MF383, MF390, MF393, MF398, MF399, MF670, MF690, MF698, MF699. Industrial: 20D, 30E, 40E, 50E, 50F. Carrier, for clutch release bearing. Carrier bore 2.130" (2-1/8" approx.); O.D. 2.503" (2-1/2"); check carrier bore before ordering. For single or dual clutch. Tractors: TO35, MF35, MF50, MF65. Industrials: 20, 202, 203, 302, 2135. Use with bearing 892862M2 for dual clutch only. 195207M1 833085M2 833084M1 834602M1 892862M2 D8NN7580CA 3702563M1 Bearing, clutch release, 2.07" I.D., 3.550" O.D.,.810" wide. Tractors: TE20, TO20, TO30, MH44, MH444, MH55, MH555. Combine: 300SP. Bearing, clutch release, 2.49" I.D., 4.10" O.D.,.875" wide, 1.535" front to back. For single clutch. Tractors: TO35, MF35, F40, MF50, MF65, MF135. Industrials: 2135, 3165. (A2336-37/A2336-147) Bearing, clutch release, 2.480" I.D., 4.100" O.D.,.850" wide. For single clutch with independent PTO. Tractors: MF165, MF175, MF180, MF255, MF265. For dual clutch. Tractors: TO35, MF35, F40, MF50, MF65, MF135, MF150, MF165, MF175, MF180, MF235, MF255, MF265, MF275, MF1100, MF1130. Industrials: 202, 203, 302, 2135. Bearing, clutch release, relubricatable. Has notch to allow lubrication. 2-1/2" I.D., 4-1/8" O.D., 13/16" wide. Tractors: F40, MF285, MF1080, MF1085, MF1100, MF1105, MF1130, MF1135, MF1150, MF1155, MF1500, MF1505, MF1800, MF1805, MF2805. Bearing, clutch release, 2.50" I.D., 3.936" O.D. Tractors: MF231, MF240, MF250, MF253, MF270, MF282, MF283, MF290, MF298, MF360, MF362, MF375, MF383, MF390, MF393, MF398, MF399, MF670, MF690, MF698, MF699. Industrials: 20D, 30E, 40E, 50E, 50F. Also used an alternate bearing on carrier 183129M2 for dual clutch. Tractors: TO35, MF35, MF50, MF65. Industrials: 20, 202, 203, 302, 2135. Clutch release bearing, 2.50" I.D., 4.090" O.D.,.865" wide. Combines: 760, 860. Replaces 256179M1. Release Bearing (Dual clutch), 2.164" I.D., 3.450" O.D.,.765" Thickness. Tractors: MF1120, MF1125, MF1140, MF1145, MF1160, MF1190, MF1220, MF1240, MF1260. MF-4-117

4 POWER TRAIN 184592M1 Bushing For Clutch Release Fork Shaft Bushing, for clutch release fork shafts. 1" I.D. x 1-1/16" x 1-1/2". (2) required for transmission case. Tractors: TO35, MF35, MF50, MF65, MF135, MF150, MF165, MF175, MF180, MF230, MF235, MF240, MF245, MF250, MF253, MF255, MF265, MF270, MF275, MF282, MF283, MF285, MF290, MF298, MF1080, MF1085. Industrials: 20, 20C, 20D, 30, 30B, 30D, 30E, 31, 40, 40B, 40E, 50, 50A, 50C, 50E, 50F, 202, 203. Forklifts: 2500, 4500, 6500. 532959M1 1862399M1 Shifter Knobs and Cover Black knobs with engraved cream color inlay shift pattern. For shift levers with 3/8" NF threads. Machine applicatin of knobs will vary depending on type of transmission. Tractors: MF135, MF150, MF165, MF175, MF230, MF235, MF245, MF255, MF265, MF275, MF285; industrials: 20, 20C, 30, 30B, 30D, 31, 40, 40B, 50C, 50D. 4-speed shift knob. Vintage Iron Hi-lo shift knob. Vintage Iron 1867690M2 Spring For Clutch Release Fork & Carrier Spring, clutch release fork to carrier (2) required. Tractors: MF135, MF150, MF165, MF175, MF180, (s/n 9A159958 & up). MF230, MF235, MF240, MF245, MF250, MF253, MF255, MF265, MF270, MF275, MF282, MF283, MF285, MF290, MF298, MF360, MF362, MF375, MF383, MF390, MF393, MF398, MF399, MF670, MF690, MF698, MF699, MF1080 (s/n 9A159958 & up), MF1085. Industrials: 20, 30, 40, 50A, (s/n 9A159958 & up). 20C, 20D, 30B, 30D, 30E, 40B, 40E, 50, 50A, 50C, 50D, 50E, 50F. Forklifts: 4500, 6500. 180006M91 520858M1 1862401M1 1013213M1 Ball type shift lever knob, transmission gearshift lever & planetary shift lever. For all TE, TO, MF models. Vintage Iron Cover, gear shift lever to shift housing. For all TE, TO, MF models. Supersedes 180579M3. Vintage Iron 3-speed shift knob. Can replace plain knob & pattern label 1682623M1 & 1682630M1. Vintage Iron Rubber gear shift boot. 2-1/16" bottom ID, 11/16" hole diameter. Tractors: MF95, MF97. Vintage Iron MF-4-118

4 POWER TRAIN Replacement parts to fit 186519M1 185464M1 1672626M1 1870860M1 Clutch Discs, Plates, and Springs Spring, piston return, for multi-power transmission, 6 required. Tractors: MF35, MF50, MF65, MF135, MF150, MF165, MF175, MF180, MF235, MF240, MF245, MF255, MF265, MF270, MF275, MF290, MF298, MF375, MF390, MF398. Industrials: 30. Clutch plate, external lugs for multi-power transmission, 3 required. Tractors: MF35, MF50, MF65, MF135, MF150, MF165, MF175, MF180, MF235, MF240, MF245, MF255, MF265, MF270, MF275, MF290, MF298, MF375, MF390, MF398. Industrials: 30. Friction disc, internal teeth, for multi-power transmission & independent PTO. For multi-power, 3 required. Tractors: MF35, MF50, MF65, MF135, MF150, MF165, MF175, MF180, MF235, MF240, MF245, MF255, MF265, MF270, MF275, MF290, MF298, MF375, MF390, MF398. Industrials: 30. For independent PTO, 7 required. Tractors: MF240, MF265 (s/n 9A349239 & up, 2-speed only), MF270, MF275 (s/n 9A349239 & up, 2 speed only), MF290, MF298, MF360, MF375, MF390, MF390T, MF398, MF399, MF670, MF690, MF698, MF699. Industrials: 30E, 40E, 50E. Replaces 185062M1, 190177M1, 514276M1, 533326M1, 1870074M1, 1870879M1. Clutch plate, external teeth, for independent PTO, 7 required. Tractors: MF240, MF265, (s/n 9A349239 & up, 2-speed only), MF270, MF275 (s/n 9A349239 & up, 2-speed only), MF290, MF298, MF360, MF375, MF390, MF390T, MF398, MF399, MF670, MF690, MF698, MF699. Industrials: 30E, 40E, 50E. 830735M91 195453M1 1754633M1 195493M1 195494M1 Transmission Parts Parts are common to all single & dual clutch, 6-speed & multi-power models: TO35, MF35, MH50, MF65, MF135, MF150, MF165, MF175, MF180, with exceptions noted. Needle bearing kit, for transmission reverse idler gear. Not for shuttle, instant reverse, or 12-speed transmissions, (1) required. Tractors: TO35 (s/n 171549 & up), MF35, MH50, MF50, MF65, MF135, MF150, MF165, MF175, MF180, MF230, MF231, MF235, MF240, MF245, MF250, MF253, MF255, MF265, MF270, MF275, MF285, MF290, MF298, MF360, MF375, MF383, MF390 (except 8 speed synchromesh), MF390T, MF1080, MF1085. Industrials: 20, 20C, 30, 31, 40, 40B, 40E, 50C, 50D, 202, 203, 204, 205, 2135, 3165. Bearing, needle, for countershaft. For all single and dual clutch, 6-speed and multi-power models. Tractors: TO35, MF35, MH50, MF65, MF135, MF150, MF165, MF175, MF180. Filter screen, transmission. Industrials: 30, 30B, 30D, 40, 40B, 50, 50A, 50C, 50D, 202, 203, 204, 205, 302, 304, 2200. Bearing, ball, for main shaft rear & countershaft. For all single and dual clutch, 6-speed and multi-power models. Tractors: TO35, MF35, MH50, MF65, MF135, MF150, MF165, MF175, MF180. Bearing, ball, for PTO drive pinion. For all single and dual clutch, 6-speed and multi-power models. Tractors: TO35, MF35, MH50, MF65, MF135, MF150, MF165. MF-4-119

4 POWER TRAIN 886089M1 899377M2 195502M2 O-ring, 4" I.D. x 5/64" thick. For transmission front PTO pinion shaft & input shaft retainer to housing. For 8-speed & late multi-power. Tractors: MF135, MF150, MF165, MF175, MF180. For all 6-, 8-, 12-speed & multi-power except where noted. Tractors: MF235 (except 6-speed), MF240 (except 6-speed), MF245 (excpet 6-speed), MF250, MF253, MF255, MF265, MF270, MF275, MF282, MF285, MF290, MF298, MF360, MF375, MF383, MF390, MF390T, MF398, MF399, MF670, MF690, MF698, MF699, MF1080, MF1085. For industrials except with instant reverse or where noted: 20 except 6-speed, 20C except 6-speed, 20D, 30 except 6-speed, 30B, 30D, 30E, 31 except 6-speed, 40B, 50A late 8-speed, 50C, 50D, 50E. Bearing, for PTO front drive shaft housing, 2.8120" O.D. Determine bearing O.D. before ordering. For 6 & 8 speed & multi-power transmission. Tractors: MF135, MF150, MF165, MF175, MF180, MF235, MF240, MF245, MF250, MF253, MF255, MF265, MF270, MF275, MF282, MF283, MF285, MF290, MF298, MF383, MF390, MF398 (also for 12 speed), MF399 (also for 12 speed), MF690, MF699, MF1080, MF1085. Industrials: 20, 20C, 20D, 30, 30B, 30D, 30E, 31, 40B, 40E, 50C, 50D, 50E. Bearing, ball, for PTO shaft. For all single and dual clutch, 6-speed and multi-power models. Tractors: TO35, MF35, MH50, MF65, MF135, MF150, MF165. 195501M1 195505M1 195507M1 195873M1 181217M3 520307M1 Oil seal, 1-1/8" I.D. x 1-9/16" O.D., for recess in rear of PTO main drive pinion shaft. For 1500/540 or 1700/540 regular transmission & 6-speed transmission with dual clutch & live PTO (not for manual shuttle or multi-power). Tractors: TO35, MF35, MH50, MF50, MF65, MF135, MF150, MF165, MF175, MF230, MF235, MF245. Industrials: 20, 20C, 30, 31, 35, 202, 203, 2135, 3165. Bearing, ball, input drive shaft. For all single and dual clutch, 6-speed and multi-power models. Tractors: TO35, MF35, MH50, MF65, MF135, MF150, MF165, MF175, MF180. Bearing, ball, for countershaft front. Also used for multi-power mainshaft front. Replaces 831469M1. For all single and dual clutch, 6-speed and multi-power models. Tractors: TO35, MF35, MH50, MF65, MF135, MF150, MF165, MF175, MF180. Bearing, needle, for power input pilot, multi-power. For all single and dual clutch, 6-speed and multi-power models. Tractors: TO35, MF35, MH50, MF65, MF135, MF150, MF165, MF175, MF180. Gasket, inspection cover on differential case. Tractors: TE20, TO20, TO30. Gasket, Steering cover transmission. For all single and dual clutch, 6-speed and multi-power models. Tractors: TO35, MF35, MH50, MF65, MF135, MF150, MF165, MF175. 521181M1 Gasket, transmission housing top differntial case. For all single and dual clutch, 6-speed and multi-power models. Tractors: TO35, MF35, MH50, MF65, MF135, MF150, MF175. MF-4-120

4 POWER TRAIN Replacement parts to fit Transmission Friction Disc & Plate For Instant Reverse Clutch 825776M1 Bolts, Nuts & Resin Kit Bolt, 1/2" x 1-45/64' NF, special head, ring gear to case. 12 used. 2757328M1 Friction disc, 5-1/4" O.D., 45 internal splines,.060" thick. For hydraulic shuttle/instant reverse clutch. Industrials: 30, 30B, 30E, 40, 40B, 50, 50A, 50C, 50D, 50E, 204, 205, 304. Replaces 1754345M1. 1754344M1 521451M1 191855M4 Friction plate, 5-7/16" O.D., 50 external splines. For hydraulic shuttle/instant reverse clutch. Industrials: 30, 30B, 30E, 40, 40B, 50, 50A, 50C, 50D, 50E, 204, 205, 304. Hydraulic Oil Filter Filter element for hydraulic lift pump, top mount. 2-7/16" O.D. 1-29/32" I.D. & 4" long. Tractors: MF35, MF50, MF65, MF85, MF88, MF90, MF1080. Industrials: 202, 203, 204, 205, 302, 304, 2135, 2200, 3165. Also the following models with pumps having 10-spline camshaft. Tractors: MF135, MF150, MF165, MF175, MF180. Industrials: 20, 30, 31, 40, 302, 304. Filter, hydraulic oil cooler, multi-power transmission. 0.985" ID, 1.775" OD, 4.500" length. Tractors: Super 90, MF135, MF165, MF175, MF180, MF1080, MF1100, MF1130. Industrials: 30, 30B, 30E, 40, 50A, 50E, 50F, 204, 205, 302, 304. 891947M1 1852913M91 184182M3 183088M1 Nut, 1/2"-20, special hex for 825776M1 bolt. High strength adhesive. Gasket for Planetary Ring Gear Gasket, for outer planetary ring gear on rear axle housing. Tractors: MF65, MF85, MF88, MF90, MF135, MF150, MF165, MF175, MF180, MF235, MF245 (prior to s/n P40085), MF250, MF253, MF255, MF265, MF270, MF275, MF282, MF290, MF360, MF375 (early models), MF383 (early models), MF390 (early models), MF670, MF690 (s/n T131043 & up, 2 wheel drive), MF1080. Industrials: 30, 30B, 30D, 30E, 31, 40, 40B, 40E, 50, 50A, 50C, 50D, 50E, 203, 205, 302, 304, 3165. Replaces 191141M2. Differential Rear Drive Coupling Drive coupling, differential, rear. Tractors: TO35, MF50, MF65. Industrials: 202, 204 Work Bull, 203, 205, 356 Tractor shovel, 2200 Treever, 2135 utility. 5" long, 10 splines 1-1/4" & 2" long. MF-4-121

4 POWER TRAIN Drive Coupler for Gear and Pinion Set 1871924M1 Coupler, 3-13/16" long, rear drive shaft to pinion. Tractors: MF230 (s/n 9A349239 & up). Industrials: 20D. We suggest measuring the pinion spline length & length of coupler to determine if 1683757M91 (4-5/16" long) was previously installed & whether 187192M1 coupler is needed. Tractors: TO35 (s/n 169467 & up), MF68, MH50, MF50, MF240 (prior to s/n 2773N01001), MF245 std. clearance (s/n 9A349239 & up). Multi-Power Transmission Parts Because of tractor &/or transmission serial numbers, early or late production, it is important to know the tooth & spline count before ordering replacement PTO pinion shaft Application Tractor: MF35 Tractor: MF50 Tractor: MF65 Tractor: MF135 Tractor: MF150 Tractor: MF165 Tractor: MF175 Tractor: MF180 Tractor: MF235 Tractor: MF245 Tractor: MF255 Tractor: MF265 Tractor: MF275 1860867M3 Seal, For PTO Pinion Shaft Retainer. Multi-Power Trans. 1.58" ID; 1.945" OD 1860889M91 Retainer Housing, PTO Pinion Shaft, Multi-Power Trans. Less Bearing & Seal. 883935M4 Seal, For PTO Pinion Shaft. Multi-Power Trans. 17 TEETH, 10 SPLINES 899332M92 PTO pinion shaft, for multi-power transmission. 17 teeth, 10 splines. Seal not included. MF-4-122

4 POWER TRAIN Replacement parts to fit Rear Axles, Bearings & Related Parts Application TO20, 16 spline TO30, 19 spline TO35, MF35, MF50, early MF135, MF150 using 19 spline end Axle Seal Outer Cup 2 3 195557M1 195557M1 195677M1 831363M1 831363M1 300975M1 Cone 4 195162M1 195162M1 195675M1 Axle Collar 5 181257M1 181257M1 180596M1 Differential Gear & Pinion Sets, Bearings Axle Seal Inner 6 195555M1 195678M2 Inner Diff. Brg. Cup 7 195160M1 195160M1 195160M1 Rear Wheel Bolt 185400M2 185400M2 185400M2 All kits contain bolts, nuts & resin kit for installation Application Ring Gear & Pinion Set Tractor: TO35 (s/n 169467 & up), MF35, MF135 (early production), MF235 531862M91 (light duty without lock) Tractor: MF135 (late production), MF235 (with lock) 531862M91 Tractor: MF65, MF165, MF175, MF180, MF235 (Orchard), MF255, MF265, MF275 Industrial Tractor: 20D 1683757M91 Tractor: TO35 (s/n 169467 & up), MF50, MF240 (to s/n 2773N01001), MF245 (standard clearance, s/n 9A349239 & up), MF230 (s/n 9A349239 & up) Gear & pinion set, 37/6 tooth count. Pinion effective spline length 4-5/16", pinion overall length 10". Used as a service replacement for several original production gear sets. This replacement required using a different drive coupler 1871924M1 (3-3/16" long). We suggest measuring the pinion & spline length & length of coupler to determine if 1683757M91 was previously installed & whether 187192M1 coupler is needed. Carrier Bearings Cup 195160M1 185252M1 185252M1 195160M1 Carrier Bearings Cone 195159M1 195160M1 185251M1 195159M1 MF-4-123

4 POWER TRAIN 181251DTC 195163M1 17392A 185778M1 Differential Sleeve Bearings Double tapered cup (53376D) for differential. Tractors: TE20, TO20, TO30, TO35 (prior to s/n 169467), MF35, MF50 (using sleeve no. 181251M91), MF65 (prior to s/n CL2686121), MF135, MF150, MF165, MF175, MF180. Cone (53177) for differential. Tractors: TO35 (s/n 169467 & up), MF50 (using sleeve 181251M92), MF35, MF135, MF150, MF165, MF175, MF180, MF235, MF255, MF265, MF275. Single cup (53375) for differential, two used. Tractors: MF35, MF135, MF150, MF165, MF175, MF180, MF235, MF255, MF265, MF275. Single cup (HM903210) two used, for differential. Tractors: TO35 (s/n 169467 & up, using sleeve 181251M93), MF35, MF65 (s/n CL2686122 & up), MF165, MF180 (using sleeve 190606M92), MF175, MF235, MF255, MF265, MF275. 1860954M1 181232M1 832954M3 181429M1 Outer oil seal in rear axle housing, for tractors with wet brakes. 2.305" ID, 3.383" OD,.562" width. Tractors: MF255, MF265 (except orchard), MF275, MF285. MF298, MF398, MF399, MF690 (prior to s/n T1301043), MF698, MF699, MF1085. Industrials: 30, 30B, 30D, 31, 40, 40B, 50A, 50C, 50D. Gasket, rear axle housing, outer. Tractors: TO20, TO30, TO35. Rear axle or differential carrier plate oil seal. 2" ID, 3.187" OD. Tractors: MF65, MF85, Super 90, MF135 orchard, MF150, MF165, MF175, MF180. Industrials: 30, 40, 50, 203, 205, 302, 304; also MF1080, MF1085, MF235 orchard, MF255, MF275, MF285 with dry brakes. Used as clutch bearing support assembly seal on tractors: MF2675, MF2705, MF2745, MF2775, MF2805. Gasket, rear axle housing, inner. Tractor: TO20. 831888M1 832954M3SK Cone (HM903249), for differential. Tractors: TO35 (s/n 169467 & up, using sleeve 181251M93), MF35, MF65 (s/n CL2686122 & up), MF165, MF180 (using sleeve 190606M92), MF175, MF235, MF255, MF265, MF275. Rear Axle Gaskets and Seals Rear axle or differential carrier plate oil seal, & speedi-sleeve. Tractors: MF65, MF85, Super 90, MF135 orchard MF150, MF165, MF175, MF180. Industrials: 30, 40, 50, 203, 205, 302, 304, also MF1080, MF1085, MF235 orchard, MF255, MF275, MF285 with dry brakes. Used as clutch bearing support assembly seal. Tractor: MF2675, MF2705, MF2745, MF2775, MF2805. 183254M1 99212 Gasket, rear axle housing, inner. Tractors: TO30, TO35, MF35, MF50, MF65, MF135, MF150, MF165. Industrials: 20, 20C, 20D, 203, 205, 302, 304. Speedi-Sleeve, 007" thick. Use with 832954M3 seal. Press on to resurface damaged shafts. Speedi-Sleeves are corrosion resistant stainless steel, smoothly finished, & ultra-thin to allow use of original seal, no oversized seal required. Saves money on replacement of shafts. SS92 Sure seal, one pair. Tractor: TO20. MF-4-124

4 POWER TRAIN Conversion PTO Assembly Replacement parts to fit Complete assembly replaces & converts 181169M91 from 1-1/8" to 1-3/8" spline. Assembled & ready to install. Includes new 1-3/8" splined PTO shaft, seal, bearing, cover, cap, & bearing retainer ring. 1860325M1 PTO shaft oil seal. 1-3/4" I.D., 2.685" O.D. Tractors: TO35, MF35, F40, MF50, MF65, MF135, MF150, MF165, MF175, MF180. 181169-38 PTO conversion assembly to 1-3/8" PTO. Tractors: TE20, TO20, TO30. 1-3/8" PTO Shaft and Components GA1773 PTO shaft ball bearing. Tractors: TE20, TO20, TO30. 181173-38 PTO shaft only, 1-3/8" 6-spline, converts original 181173M1 from 1-1/8" 6-spline, to 1-3/8" 6-spline. Tractors: TE20, TO20, TO30 (includes 181183-38 retainer sleeve). 825787M1 PTO cap, aluminum alloy replacement. Tractors: TE20, TO20, TO30 all with 1-1/8" or 1-3/8" shafts. 181183-38 Retainer sleeve for Tisco 181173-38, 1-3/8" 6-spline PTO shaft. 181204M92 PTO shaft, 1-3/8" dia. 6-spline. Tractors: MF35, TO35, MF50, MF135. 195763M1 PTO shaft oil seal. 1-5/8" I.D., 2.450" O.D. Tractors: TE20, TO20, TO30. Same as D9NN703BB. MF-4-125

4 POWER TRAIN Bearings for PTO Output Shaft 835015M1 Bearing for PTO stub shaft, 540 RPM. Tractors: MF285, MF1085. (88508) 195498M1 834216M1 CRK600 Bearing, outer, for PTO output shaft. 45mm ID, 75mm OD, 16mm width. Tractors: TO30, MF35, MH50, MF50, MF65, MF135, MF150, MF165, MF175 (late model), MF235. For models with dry brakes. Tractors: MF255, MF265 (prior to s/n 9A349239), MF275 (to s/n 9A349239). For models using snap rings on bearing. Tractors: MF180, MF230. Industrials: 30, 31, 40 (with dry brakes), 202, 203, 302, 2135, 3165, 20 (with snap ring & bearing). Oil Seal For PTO Output Shaft Oil seal, outer, for PTO output shaft. Tractors: MF230 (axle s/n FD101, CD8028 & up), MF231, MF235 (live PTO with axle s/n FD101 & up), MF240, MF245, MF250, MF253, MF255 (with wet brakes), MF265 (with wet brakes), MF270, MF275, MF282, MF285, MF290, MF298, MF360 (prior to s/n P38370), MF375, MF383, MF390, MF390T, MF398, MF399, MF670, MF690, MF698, MF699, MF1080, MF1085, MF3050, MF3060, MF3070, MF3090. Industrials: 20 (axle s/n FD101, CD8028 & up), 20C, 20D, 30 (with wet brake), 30B, 30D, 30E, 31 (axle s/n FD101, CD8028 & up), 40 (with wet brake), 40B, 40E, 50C, 50D, 50E. Over-Running Couplers Coupler repair kit, services all Hub City over-running couplers. Contains keys, roll pin, set screw, springs, spacer, & retaining ring. MF-4-126

5 WHEELS AND ALES Replacement parts to fit Steering Wheel Steering Wheel Cap 180576M1 180576M1-OE 772064M1 850071M1 1013317M91 Steering wheel, 17-3/4" diameter, 3/4" hub with 3/16" keyway. Tractors: TE, TO20, TO30, TO35, MF35, MF135, MF50, MF65. Vintage Iron Steering wheel OEM style, 17-3/4" diameter, 3/4" hub with 3/16" keyway, METAL SPOKES. Tractors: TE, TO20, TO30, TO35, MF35, MF135, MF50, MF65. Vintage Iron Steering wheel, 17-3/4" diameter, 5" dish, splined hub. Tractors: MF230 (with power steering, prior to s/n 9A349239 & late production manual), MF235 (with power steering s/n 9A214239 & up, except orchard diesel), MF245 (prior to s/n 9A349239), MF255 (prior to s/n 9A324137), MF265 (prior to s/n 9A349239), MF1500, MF1505, MF1800, MF1805. Industrials: 20C diesel (prior to s/n 9A332668 & early gas with 5" dish), 30B diesel (prior to s/n 9A331748 & all gas), 40B (prior to s/n 9A331974). Combines: 540, 750 (s/n 1696016539 & up), 760 (s/n 1746009413 & up), 8570. Replaces 525681M2. Vintage Iron Steering wheel, 3 spoke (uncovered). 15" diameter, 11/16" 3/4" shaft. Tapered, keyed, & stepped hub. Tractors: Massey Harris: Pony, Pacer. Vintage Iron Steering wheel, 3 spoke (covered). 18" diameter, 7/8" 13/16" tapered shaft. Keyed hub. Tractors: 95. Vintage Iron 1870806M91 Cap, for steering wheel. Tractors: MF231, MF270, MF283 (except Brazil), MF290, MF298, MF670, MF690, MF698, MF699. Industrials: 50E. For non-telescoping steering column. Tractors: MF4800, MF4840, MF4880, MF4900. Vintage Iron Steering Column Grommet 186627M1 Steering column grommet. 3.660" length x 3.085" width x 1.480" hole I.D. Tractors: MF35 (s/n 204181 & up). Industrials: 202, 203, 204, 205. Vintage Iron 181365M1 832397M1 760906M1 760907M1 Steering Shaft & Bearing Shaft, steering gear. Tractors: TE20, TO20, TO30. 13-1/2" long. Bearing inner cone, use with 181365M1. Roller bearing, use with 181365M1. Bearing cup, steering shaft. Use with 181365M1. Steering Gear Thrust Bearing New design one piece "mono-bearing" replaces conventional bearing cup & cone. Made of a new material called Delrin, similar to nylon used in industrial applications. This new material is self-lubricating & very resistant to wear & shock, resists high temperature & high pressure deformation. Easy-to-follow replacement instructions are included with each bearing. 8N3571-52 Mono-bearing, for steering shaft on tractors with manual steering. Tractors: TO35, MF35, MF135. Industrials: 35, 2135. Replaces 1-180526M1 (10790Z) cup, & 1-180549M1 (10790S) cone. 2 required per tractor. 1-3/4" O.D., 7/8" I.D., 7/16" wide. MF-5-127

5 WHEELS AND ALES 897235M1 194624M1-HD Bushing for Steering Shaft Bushing (metal), for steering shaft, used in front axle support, 2 required. Tractors: MF165 (except LPG), MF175, MF255 (prior to s/n 9A324146), MF265 (prior to s/n 9A324139), MF270, MF275 (prior to s/n 9A324137), MF282, MF283 (except Brazil), MF290, MF670, MF690, MF699. Industrials: 30, 31, 3165. Also used in power rack, upper bushing only. Tractors: MF180 (s/n 9A48873 & up), MF1080, MF1100, MF1130, MF1150, MF1155. Row crop & western models. Tractors: MF1085, MF1105, MF1135. Replaces 194624M1, 533792M1. Bushing (Moly type), for steering shaft, used in front axle support, 2 required. Tractors: MF165 (except LPG), MF175, MF255 (prior to s/n 9A324146), MF265 (prior to s/n 9A324139), MF270, MF275 (prior to s/n 9A324137), MF282, MF283 (except Brazil), MF290, MF670, MF690, MF699. Industrials: 30, 31, 3165. Also used in power rack, upper bushing only. Tractors: MF180 (s/n 9A48873 & up), MF1080, MF1100, MF1130, MF1150, MF1155. Row crop & western models. Tractors: MF1085, MF1105, MF1135. Replaces 194624M1, 533792M1, 897235M1. 2.015" O.D., 1.900" I.D., 1.675" long. 3401240M91 3401241M91 3401553M92 Power Steering Cylinder and Parts Heavy-duty cylinder comes complete with both ball joint ends and is repairable. Universal design, can be used on left or right side on tractors equipped with 2 cylinders mounted behind front axle. The OEM no longer supplies this part. They replace with individual left hand or right hand cylinders at greater cost. Power steering cylinder, Left hand with two ball joint ends. 12-1/2" long, 5/8" dia. rod, 5.640" stroke. Tractors: MF135 orchard, MF240, MF250. Industrials: 20, 35 utility, 202, 203, 204, 205, 2135, MF20D, MF20E. Replaces 192749M92. Power steering cylinder, Right hand with two ball joint ends. 12-1/2" long, 5/8" dia. rod, 5.640" stroke. Tractors: MF135 orchard, MF240, MF250. Industrials: 20, 35 utility, 202, 203, 204, 205, 2135, MF20D, MF20E. Replaces 192749M92. Cylinder, steering complete (9" long) for hydrostatic or power steering. Tractors: MF240, MF253, MF360, MF362. Industrials: MF20F, MF30E, MF30H, MF40E. Replaces 3774728M91. Bushing for Steering Assembly 190560M1 Bushing, main steering arm assembly or power steering cylinder support. Tractors: MF50, MF65, MF135, MF150, MF165, MF175, MF255, MF265, MF270, MF275, MF282, MF285, MF290, MF670, MF690. Industrials: 30, 31, 50F, 50H, 302, 304. (3/4" x 7/8" x 1-1/4") MF-5-128

5 WHEELS AND ALES Replacement parts to fit Power Steering Cylinder Ends Power Steering Pumps 1033035M92 192749FT 192749MT 185452M1 CK34 Ball joint end assembly, for power steering cylinder. Tractors: MF235 orchard diesel, MF245 orchard (with cyl. 519283M91, 519284M91, 532225M91 or 532226M91), MF265 (s/n 9A324139 & up with cylinder 579149M91 & 579160M91), MF285 (s/n 9A281393 & up). Industrials: 20C, 30B, 30D (all with cyl. 532225M91 & 532226M91), 40, 40B (with cyl. 532225M91 & 532226M91), 80 backhoe loader. Forklifts: 2200, 4500. Rod end ball joint, with internal threads. For Tisco universal power steering cylinder 192749M92 (sold until 2006). Cylinder head tie rod end, with external threads. For Tisco universal power steering cylinder 192749M92 (sold until 2006). Dust Boot. Universal, 1.200" base x.475" height x.500" hole I.D. Front power steering cylinder ends (will not fit rear cylinder ends). Tractors: TE20, TEA20, TO20, TO30, TO35, MF20, MF35, MF135, MF230, MF235, MF2135, Super 90. Industrials: 202, 203, 205. Vintage Iron Seal Kit For Power Steering Cylinder Seal kit, for power steering cylinders on tractors with 2-cylinder operation. Industrials: 50, 50A, 70 backhoe loader (s/n 119750021 & up), 356 tractor shovel (s/n 670001371 & up). Forklift: 2200, 2500. Also for original production cylinders 519283M91, 519284M91, 532225M91, 532226M91. Tractors: MF235 orchard, MF245 orchard. Industrials: 20C, 30B, 30D, 40, 40B. Forklift: 4500. 523089M91 523090M91 523092M91 773126M92 Power steering pump, straight cut gear, 14 teeth, replaces Parker Hannifin. Tractors: MF285, MF1080, MF1085 (except with hydrostatic p/s pump). Replaces 517022M93. When installing 523089M91 as replacement for 517022M93, MF indicates it is necessary, on some models, to install different lines & fittings. For repairs order seal kit PSP-KIT1. Power steering pump, helical cut gear, 13 teeth, replaces Parker Hannifin. Tractors: MF65 diesel (s/n 685996 & up), MF165 diesel, MF255 gas. Industrials: 30 diesel, 40B, 50A, 302 diesel, 304 diesel, 356 diesel, 3165 diesel. Replaces 188772M92 & 518633M91. For repairs order seal kit PSP-KIT1. Power steering pump, helical cut gear, 14 teeth, replaces Parker Hannifin. Tractors: MF165 Perkins gas, MF175, MF255 diesel, MF265 (except with hydrostatic p/s pump), MF275. Industrials: 30 gas, 31, 50C, 50D, 6500 forklift. Replaces 505341M91, 518637M92 & 897146M94. When installing 523092M91 as replacement for 505341M92, 518637M92, or 897146M94, MF indicates it is necessary to install different lines & fittings. For repairs, order seal kit PSP-KIT1. Power steering pump, straight cut gear, 13 teeth, includes drive gear, reservoir & adjustable relief valve preset at 1500 psi. in tractors using Perkins 3 cyl. gas or diesel engines. Tractors: MF35, MF50, MF135, MF150, MF230, MF235, MF245, MF250. Industrials: 20, 20C, 30B, 30D, 30E, 40, 203, 205, 2135, 2200. Forklift: 2500, 4500. Replaces 193208M91, 518369M92, 527904M91. MF-5-129

5 WHEELS AND ALES 773126M92-IMP 544443M91 3382280M1 1696665M91 1695445M91 3597420M91 Power steering pump, straight cut gear, 13 teeth, includes drive gear, reservoir & adjustable relief preset at 1500 psi. Tractors: MF35, MF50, MF135, MF150, MF230, MF235, MF245, MF250. Industrials: 20, 20C, 30B, 30D, 30E, 40, 203, 205, 2135, 2200. Forklift: 2500, 4500. Replaces 182493M92, 191277M91, 191423M92, 191426M91, 191486M91. Replaces 773126M92. Power steering pump, helical cut gear, 12 teeth, for tractors with Continental gas engines. Tractors: TO35 (Standard Motors diesel & Cont. gas), MF35, MF50, MH50, MF135, MF150. Industrials: 35, 202, 204, 2135. Forklift: 2500. Replaces 182493M92, 191277M91, 191423M92, 191426M91, 191486M91. Hydraulic steering/tandem pump. Tractors: MF3050, MF3060, MF3065, MF3070, MF3080, MF3085, MF3090, MF3095, MF3115, MF3120, MF3125, MF6110, MF6120, MF6130, MF6140, MF6150, MF6160, MF6170, MF6180, MF6190, MF6235, MF6245, MF6255, MF6260, MF6265, MF6270, MF6280, MF6290. Replaces 3616060M1. Power steering pump. Tractors: MF362, MF365, MF375, MF383, MF390, MF390T. Replaces 3774616M92. Steering orbital motor. Tractors: MF240, MF253, MF261, MF263, MF271, MF360, MF362, MF365, MF375, MF383, MF390, MF390T, MF393, MF398, MF399, MF4225, MF4233, MF4240, MF4243, MF4245, MF4253, MF4263, MF4270. Replaces 1695444M91. Hydraulic/power steering pump. Tractors: MF399 w/a6-354.4 engine. Replaces 3595383M91. 1635948M92 PSP-KIT1 PSP-KIT2 1886135M1 1662566M1 183174ML Repair & Seal Kits Seal kit, power steering pumps. Tractors: MF270, MF283, MF298, MF670, MF690, MF698. For pump 1696666M91 on tractors: MF375, MF383, MF390. For pump 1662243M91 on tractor: MF282. For pump 1666726M92 on tractor: MF290. Repair kit, power steering pump. Contains seals, o-rings, gaskets, thrust & wear plates. For pumps 523089M91, 523090M91, 523091M91, 523092M91, 523093M91. Seal kit, power steering pump. Contains, seals & gaskets. For pumps 523089M91, 523090M91, 523091M91, 523092M91, 523093M91. Filters for Power Steering Pumps Oil filter element, power steering pump. Tractors: MF253. For Plessey pumps. Industrials: 20 (s/n 9A132003 & up). Forklift: 2500 (late production with Perkins eng.), 4500 (with Perkins diesel). Replaces 3475940M1. Oil filter element, power steering pumps. Tractors: MF270, MF282, MF283, MF290, MF298, MF375, MF383, MF390, MF670, MF690, MF698. Also for original Plessy pump #550-1-16688. Tractors: MF255, MF265 (prior to s/n 9A349239), MF275 (prior to s/n 9A349239). Industrials: 50C. Power Steering Plate Power steering plate. Mounts under steering wheel nut. 2-1/2" O.D., 5/8" center hole with keyway. Anodized red aluminum. Tractors: MF35, MF65, MF85, MF88, Super 90. Industrials: 202, 203, 204, 205, 303, 404. Vintage Iron MF-5-130

5 WHEELS AND ALES Replacement parts to fit Run Tee Used with power steering lines. Axle Lock Bolt Secures axle extension to axle assembly. Our bolt is 1/2" longer to accommodate front bumper. 35882891 183221M1 180344M1 182850M1 1660114M2 Run tee for power steering lines, 37 JIC, adjustable O.R.B., threads 9/16"- 18 for 3/8" O.D. tube. Used on a wide range of ag & industrial tractors primarily with the power steering lines. Front Axle Pivot Pin Pivot pin for swept back axles. 1-3/4" O.D., 4-3/4" long. Has 7/8" dia. bolt hole & 1" dia. crank hole. Tractors: TO20, TO30, TO35, MF35, MF135 (prior to s/n 9A86902). Industrials: 20 (prior to s/n 9A86902), 2135 turf & narrow. Replaces 193746M1. Use with flanged axle bushing 182850M1. Axle Support Bushings Front pivot support bushing. Tractors: TE20, TO20, TO30, TO35. 1-15/16" O.D., 1-25/32" I.D., 1-1/2" long. Front pivot support bushing, flanged. For swept back axles. Tractors: TE20, TO20, TO30, TO35, MF35, MF135, MF235. Industrial: 20, 2135. 2.075" O.D., 1.750",.820" long. Bushing front axle support pivot pin. For straight adjustable axles. Tractors: MF135 vineyard, MF235, MF245 vineyard. Replaces 888314M1. 523387M1-L 3534351 180381M91 180391M91 182534M91 Lock bolt for adjustable front axles. Tractors: F40, MH50, MF50, MF65, MF150, MF175, MF230 (s/n 9A243032 & up), MF245 semi-swept, MF255, MF265, MF275. Industrials: 20C, 30, 31, 3165 turf. Can replace 182501M1. Usable length 3-3/4", 5-1/8" overall, 3/4"-16 thread. Hex nut, 3/4" SAE, for lock bolt 523387M1 for adjustable front axles. Tractors: F40, MH50, MF50, MF65, MF150, MF175, MF230 (s/n 9A243032 & up), MF245 semi-swept, MF255, MF265, MF275. Industrials: 20C, 30, 31, 3165 turf. Front Axle Drag Link Ends Length shown is from end of shaft/tube to center of post/ball stud. Drag link end assembly, front, 3.250" to center of post,.687"-18 right hand thread. Tractors: TO20, TO30, TO35, MF35. Drag link end assembly, rear, 3.594" to center of post,.687"-18 left hand thread. Tractors: TO20, TO30, TO35, MF35. Drag link end assembly, front. 3.75" to center of post,.812"-16 right hand thread. For drag links with adjustable end. Tractors: F40, MH50, MF50, MF65, MF135 orchard, MF150, MF165, MF175. Industrials: 20, 35 utility, 202, 203, 204, 205, 356 tractor shovel, 2135 utility, 3165. 826752M92 Drag link end, rear, threaded. 3" to center of post. Tractors: MF135, MF240, MF250. Industrials: 20D with adjustable axle, 2135 narrow axle. Replaces 969352M1. MF-5-131

5 WHEELS AND ALES Front Axle Tie Rod Parts With adjustable front axle *Length shown is fron end of shaft/tube to center of post/ball stud 182519M91 Inner tie rod end, right hand, adjustable. 6" to center of post,.812"-16 right hand thread. For hi & lo clearance tractors. Tractors: MF50 & MH50 (prior to s/n 528163), MF65 (gas, prior to s/n 671680), MF65 (diesel, prior to s/n 667918). 186235M91 Outer right hand tie rod end for hi & lo clearance tractors, 14.656" to center of post,.737" O.D. Tractors: MF50 & MH50 (prior to s/n 528163), MF65 (gas, prior to s/n 671680), MF65 (diesel, prior to s/n 667918). Replaces 182515M91. 186077M92 Inner tie rod end, right hand, adjustable. 6.50" to center of post,.812"-16 right hand thread. For hi & lo clearance models. Tractors: MF50 (s/n 528163 to 533422), MF65 (gas, s/n 671680 to 692932), MF65 (diesel, s/n 667918 to 692932). 186236M91 Outer left hand tie rod end for hi & lo clearance tractors, 14.656" to center of post,.737" O.D. Tractors: MF50 & MH50 (prior to s/n 528163), MF65 (gas, prior to s/n 671680), MF65 (diesel, prior to s/n 667918). Replaces 182507M91. 1028262M91 Tie rod end, left hand or right hand, outer. 15" to center of post,.742" O.D. Notched, adjustable, for front axle. Tractors: MF165 (except LP), MF175, MF255, MF265 (except Orchard), MF275. Industrials: 30 Turf, 3165 Turf. 182517M91 Tie rod tube, right hand, for hi & lo clearance tractors, overall length 18.375". Tractors: MF50 & MH50 (prior to s/n 528163), MF65 (gas, prior to s/n 671680), MF65 (diesel, prior to s/n 667918). 1028264M91 Tie rod tube with end, right hand, inner, includes clamp. 20.125" to center of post,.75" I.D. For adjustable front axle. Tractors: MF165 (except LP), MF175, MF255, MF265 (except Orchard), MF275. Industrials: 30 Turf, 3165 Turf. 186061M91 Inner tie rod, left hand for hi & lo clearance tractors, overall length 15.25". Tractors: MF50 (s/n 528163 to 533422), MF65 (gas, s/n 671680 to 692932), MF65 (diesel, s/n 667918 to 692932). 1028098M1 Tie rod end, left hand, inner. 4.812" to center of post, 1" O.D., female thread. For adjustable front axle. Tractors: MF165 (except LP), MF175, MF255, MF265, MF275. Industrials: 30, 31, 3165 Turf. MF-5-132

5 WHEELS AND ALES Replacement parts to fit 1028099M91 Tie rod tube with clamp, LH, 13-3/8" overall length. For adjustable front axles. Tractors: MF165 (except LP), MF175, MF255, MF265 (except Orchard), MF275. Industrials: 30 Turf, 3165 Turf. 1048272M91 Tie rod end, left hand, slotted, 32.843" to center of post,.937" O.D., includes boot & grease fitting. For semi-swept adjustable axle. Tractors: MF230 (s/n 9A243032 & up), MF245 (including vine & narrow orchard). Industrials: 20C Turf. 1028265M92 Tie rod end, outer left hand or right hand, slotted. 15.487" to center of post,.937" O.D. For adjustable front axle. Tractors: MF180, MF1080, MF1085. 1048273M92 Tie rod end, threaded, includes boot & grease fitting. 3.840" to center of post, 1"-16 right hand threads,.705" small part of taper. For semi-swept adjustable axle. Tractors: MF230 (s/n 9A243032 & up), MF245 (including vine & narrow orchard). Industrials: 20C Turf. 1028266M91 Tie rod tube with clamp, for left hand or right hand. 16.562" overall length, 1"-16 female thread. For adjustable front axle. Tractors: MF180, MF1080, MF1085. 881736M92 Tie rod end, outer, LH or RH, recess for set screw (7). 14-3/4" to center of post. For adjustable front axle. Tractors: MF270, MF282, MF283 (except Brazil), MF670, MF690. 1028268M92 Tie rod end, inner, left hand or right hand, 3.875" to center of post, 1"-16 right hand thread. For adjustable front axle. Tractors: MF180, MF1080, MF1085. 1044295M91 Tie rod end inner, right hand, slotted, 15.5" to center of post,.937" O.D. Tractors: MF285 (with adjustable front axle). 1048271M91 Tie rod center tube with clamp, bolt, nut & lock washer. 33" overall length, 1"-16 female thread. For semi-swept adjustable axle. Tractors: MF230 (s/n 9A243032 & up), MF245 (except vine & orchard). Industrials: 20C Turf. MF-5-133

5 WHEELS AND ALES 1044294M92 Tie rod end outer, right hand, 5.03" to center of post, 1"-16 right hand thread. Tractors: MF285 (with adjustable front axle). 1026383M91 Tie rod end, inner, left hand or right hand. 4" to center of post, 1"-16 right hand thread. For adjustable or fixed front axle. Tractors: MF1100, MF1105, MF1130, MF1135, MF1150, MF1155. 886801M91 Tie rod tube, RH, includes set screw & lock nut. 17-3/4" overall length. For adjustable front axle. Tractors: MF270, MF282, MF283 (except Brazil), MF670, MF690. 3045062M91 Tie rod end, threaded, 5" to center of post. For fixed & adjustable front axles. Tractors: MF2675, MF2705. 1044297M91 Tie rod end with socket & clamp, inner, left hand, 17" to center of post. Tractors: MF285 (with adjustable front axle). UTRB Universal tie rod boot. 1.300" base x.965" height x.500" hole I.D. Vintage Iron 1044298M91 Tie rod end outer, left hand, slotted. 15.5" to center of post,.937" O.D. Tractors: MF285 (with adjustable front axle). 358209R1 Tie Rod Boot. Base 1.450" x Height.600" x Hole ID.550". Vintage Iron Steering Arms 1026382M93 Tie rod end, slotted, left hand or right hand. 16.312" to center of post,.937" O.D. For adjustable front axle. Tractors: MF1100, MF1105, MF1130, MF1135, MF1150, MF1155. 194570M1 194569M1 Steering arm. Left hand arm. Tractors: MF165, MF175, MF255, MF265, MF275, MF285. Industrials: MF630, MF31, MF3165. Steering arm. Right hand arm. Tractors: MF165, MF175, MF255, MF265, MF275, MF285. Industrials: MF630, MF31, MF3165. MF-5-134

5 WHEELS AND ALES Replacement parts to fit Spindle Assemblies 897456M96 Spindle assembly, Right hand. (Vertical shaft 11.00"). Tractors: MF175 UK. 897457M96 Spindle assembly, Left hand. (Vertical shaft 11.00"). Tractors: MF175 UK. 3697027M91 Spindle assembly, Right hand (used with 348mm axles). (Vertical shaft 12.687"). Tractors: MF375, MF390, MF390T, MF393, MF396, MF398, MF399. 897236M94 Spindle assembly, Right hand. (Vertical shaft 11.060" x 1.245" dia). Tractors: MF35 UK (s/n 358616 & up), MF135 UK, MF240. 3697028M91 Spindle assembly, Left hand (used with 348mm axles). (Vertical shaft 12.687"). Tractors: MF375, MF390, MF390T, MF393, MF396, MF398, MF399. Front Axle Knees 897237M94 Spindle assembly, Left hand. (Vertical shaft 11.060" x 1.245" dia). Tractors: MF35 UK (s/n 358616 & up), MF135 UK, MF240. 508571M92 Spindle, LH, or RH, for standard adjustable axles. Vertical shaft, 12-7/16" x 1.492". Not for row crop wide, orchard or lo-profile. Tractors: MF165 (except LPG), MF175, MF255 (to s/n 9A324146), MF265 (to s/n 9A324139), MF275 (to s/n 9A324137). 888300M92 Front axle knee, Right hand, HD. (Vertical height 8.750"). Tractors: MF135 UK (s/n 140128 & up), MF235 (std straight axle), MF240. 897475M95 897476M95 Spindle assembly, Right hand. (Vertical shaft 13.187" x 1.50" dia). Tractors: MF165 UK high clearance (to s/n 508597), MF255 row crop (export, to s/n 9A282625), MF270 std, MF282, MF283 std clearance, MF290 std clearance. Spindle assembly, Left hand. (Vertical shaft 13.187" x 1.50" dia). Tractors: MF165 UK high clearance (to s/n 508597), MF255 row crop (export, to s/n 9A282625), MF270 std, MF282, MF283 std clearance, MF290 std clearance. 888304M92 Front axle knee, Left hand, HD. (Vertical height 8.750"). Tractors: MF135 UK (s/n 140128 & up), MF235 (std straight axle), MF240. 898221M95 898222M95 Spindle assembly, Right hand. (Vertical shaft 10.00" x 1.50" dia). Tractors: MF165 (UK HD & South Africa), MF255 std (export), MF270 lo-clearance, MF290. Spindle assembly, Left hand. (Vertical shaft 10.00" x 1.50" dia). Tractors: MF165 (UK HD & South Africa), MF255 std (export), MF270 lo-clearance, MF290. 897471M91 Front axle knee, Right or Left hand, HD. (Vertical height 10.625"). Tractors: MF165 UK (to engine s/n 508598), MF175 UK (s/n 724936 & up), MF178 (s/n 724936 & up), MF255 (to s/n 9A282265), MF270, MF282, MF283 (std clearance), MF290 (std clearance). 897230M94 Spindle assembly, Right hand. (Vertical shaft 11.500" x 1.50" dia). Tractors: MF165 UK, MF240, MF250. Industrials: MF20D, MF20E. 897231M94 Spindle assembly, Left hand. (Vertical shaft 11.500" x 1.50" dia). Tractors: MF165 UK, MF240, MF250. Industrials: MF20D, MF20E. 898220M91 Front axle knee, Right or Left hand. (Vertical height 7.625"). Tractors: MF165, MF255 (std), MF270 (low clearance), MF290 (low clearance). MF-5-135

5 WHEELS AND ALES Front Spindles, Bearings and Axle Parts Application Tractor: TE20, TO20, TO30, TO35, MF35, FE35 (Right Hand) Tractor: TE20, TO20, TO30, TO35, MF35, FE35 (Left Hand) Industrial Tractor: 40 Tractor: MF65, MF50 (Right Hand) Industrial Tractor: 40 Tractor: MF65, MF50 (Left Hand) Tractor: MF135, MF235 Tractor: MF150, MF165, MF175, MF180, MF245, MF255, MF265, MF275, MF1080 Tractor: MF85, MF90, Super 90 Tractor: MF1100, MF1130, MF1105, MF1135, MF1150 Industrial Tractor: 30 Tractor: MF255, MF265, MF275, MF285, MF1085 Spindle (A) Bushing (B) 180346M92 180345M1 18560 180349M92 180345M1 18560 182559M92 196060M1 18560 182560M92 196060M1 18560 508546M92 180345M1 18560 Thrust Seal and Bearing Wear (C) Sleeve (D) 180008M1 180008M1 180008M1 180008M1 833342M1 194620M1 833342M1 194620M1 831635M1 503939M1 833355M1 194494M1 Inner Cone (E) 3503511 15123BR 3503511 15123BR 3503511 15123BR 3503511 15123BR 831078M1 LM48548 831078M1 LM48548 701114M1 831703M1 3780 701114M1 Inner Cup (F) 763402M1 15245 763402M1 15245 763402M1 15245 763402M1 15245 831077M1 LM48510 831077M1 LM48510 172011 25520 831363M1 3720 172011 25520 Outer Cone (H) 150662M1 09067 150662M1 09067 150662M1 09067 150662M1 09067 831055M1 LM11949 831055M1 LM11949 3543701 LM67048 25877 3543701 LM67048 Outer Cup (G) 850127M1 09195 850127M1 09195 850127M1 09195 850127M1 09195 831054M1 LM11910 LM11910 3543691 LM67010 25821 3543691 LM67010 Bearing Kit (J) 835964M91 835964M91 835964M91 835964M91 835965M92 835965M92 FW85 839100M91 FW86 MF-5-136

5 WHEELS AND ALES Replacement parts to fit Special Spindle Thrust Bearing Front Axle Spindle Bushings 180345M1 Spindle bushing. Tractors: TE20, TO20, TO30, TO35, FE35, MF35, MF135 (deluxe, special, and vine with swept back axle), MF235 (except orchard, & vine). Industrials: 20 turf, 2135 (except turf). 1.375" O.D., 1.240" I.D., 1.500" long. 196167M91-SP 18560 832961M1 Replaces OEM ball bearing unit Special spindle thrust bearing made of molybdenum disulfide impregnated nylon made to outlast original ball-type bearing by as much as three to one Designed for use where severe applications require both high friction and heavy load wear resistance Spindle thrust bearing. Tractors: MF65 Utility, MF50 Multi purpose, MF135 Orchard only, MF165 South Africa, MF175 Minute Maid Corp, MF230 Semi swept axle, MF235 Diesel (Gas s/n 9A210647 & up), MF245 (standard-vine-narrow orchard semi swept Orchard, no adju.), 202, 203, 204, 205, 2135 utility (with solid axle), 3165 utility (with solid axle), 2200 tractor, 4500 forklift, 20 industrial (with solid axle), 30 industrial (with solid axle), 40 industrial and navy (with solid axle), 31 industrial, 20C industrial (with solid axle), 30B industrial, 40B industiral (prior to s/n 9A326404). Spindle thrust bearing. 1-1/4" I.D., 2-3/16" O.D., 5/8" deep. Tractors: MF35 (dual slot spindle), TE20, TO20, TO30, TO35, MF35, FE35, F40, MF50, MF65 (low and hi clearance), MF135 (deluxe and standard), MF235 Vine (with either swept or straight axle), MF235 (standard swept axle), MF245 Vine (with straight axle), MF230 (with swept axle), 2135 Turf (narrow vine), 20 Industrial (turf adjustable), MF150 (Standard and Row), MF165 (row crop LPG). Thrust bearing, front axle spindle. 1.772" I.D., 2.875" O.D.,.787" deep. Industrials: 40B (s/n 9A326404 & up), 50, 50A, 50C, 50D, 50E, 302, 304. Forklifts: 2500, 6500, 6500H. 196060M1 183086M1-HD Spindle bushing. Tractors: F40, MH50 (except multi-purpose), MF50, MF65 (except utility), MF150 (prior to s/n 9A243032 with swept back axle), MF165LPG. 1.450" O.D., 1.240" I.D., 1.500" long. Special Moly bushings replace steel OEM part. Moly bushings have superior wear tolerance, self-lubricating, no machining. Spindle bushing (Moly type). Tractors: MH50 multi-purpose, MF65 utility, MF85, MF88, Super MF90, MF135 orchard, MF150 (s/n 9A243032 & up with semi-swept axle), MF165 (except LPG), MF175, MF180, MF230 (s/n 9A243032 & up with semi-swept back axle), MF235 orchard, MF245 (except vineyard), MF255, MF265, MF275, MF285, MF1080, MF1085. Industrials: 20 (except turf), 20C, 30 turf, 30B, 30D, 35 utility, 40, 40B (prior to s/n 9A326404), 202, 204, 205, 405, 302 (prior to s/n 119700021), 304 (prior to s/n 119750021), 2135 utility, 3165 turf. Forklift: 4500. 1.735" O.D., 1.500" I.D., 1.500" long. MF-5-137

5 WHEELS AND ALES Dust Seal For Front Axle Spindle Wheel Bearing Kits 183021M2 LN10-2 LN10-5 897702M1 Dust seal, felt, 1-15/32" I.D. x 2-9/64" O.D. x 1/4" wide. For top of front axle spindle. Tractors: MH50 (fixed axle), MF65 (fixed axle), MF85, MF88, MF90, MF135 (fixed axle), MF165 (except LPG), MF175, MF180, MF230 (except swept back axle), MF231, MF235 orchard, MF240 (prior to s/n 2773N01001), MF245 (except vineyard with fixed axle), MF250, MF253, MF255, MF265, MF270, MF275, MF282, MF283, MF285, MF290, MF360, MF670, MF690, MF1080, MF1085. Industrials: 20 (fixed axle), 20C, 20D, 30, 30B, 30D, 30E, 31, 35 utility, 40, 40B, 40E, 200 (fixed axle), 302 (prior to s/n 119700021), 304 (prior to s/n 119750021), 2135 utility, 3165. Wheel Clamp Lock Nut No re-threading necessary on worn shafts. Directions: put on inside sleeve nut (A) & adjust to suit bearing; hold with wrench in position while screwing on outside ring nut (B) tightly. Picture (C) shows the lock nut complete. 3/4" - 16 7/8" - 14 Front Axle Grease Seal For Hub Front axle hub seal. 2.362" I.D., 3.374" O.D. Tractors: MF250 (with 6.00 x 10 rim), MF253 (with 179mm high axle), MF270, MF282, MF283 (except Brazil), MF290, MF298, MF360, MF375, MF383, MF390, MF398, MF399, MF670, MF690, MF698, MF699. Industrials: 20D (with fixed axle), 30E, 40E. 835965M92 FW86 194621M1 882637M1WF Wheel bearing kit, for front wheel using 5-1/2" wide hub 519278M91. Tractors: MF135, MF150, MF165, MF175, MF180, MF230, MF235 (except vine & orchard), MF245 (except vine & orchard), MF255 (prior to s/n 9A324145), MF265 (prior to s/n 9A324138), MF275 (prior to s/n 9A324136), MF1080, MF1085 (all tricycle and early production with hub using 9/16" national fine wheel bolts, not for fixed or adjustable axle). Industrials: 20, 20C turf, 30 turf, 2135 (s/n 646002326 & up, using 6-hole hub, except narrow). Wheel bearing kit, for front wheels using 5-1/4" wide hub 532781M91. Tractors: MF225 (s/n 9A324146 & up), MF265 (s/n 9A324139 & up), MF275 (s/n 9A324137 & up), MF285, MF1085 (late production with fixed or adjustable axle). Not for tricycle axle or hub using 9/16" national fine wheel bolts. Industrial: 30 (except turf). Front Hub Caps Hub cap, front wheel, threaded O.D. 3" for front hubs with threaded recess. Tractors: MF135, MF150, MF165, MF175, MF180, MF235, MF255, MF265, MF275, MF1000, MF1080, MF1085, MF1105, MF1130, MF1135. Industrials: 20, 30, 2135, 3165. Hub cap, front wheel, threaded O.D. 2-3/4", with grease fitting. For front hubs with threaded recess. Tractors: MF250 (with split rim 6.00 x 10), MF253 (with 179mm high axle), MF270, MF282, MF283 (except Brazil), MF290, MF360, MF375, MF383, MF390, MF398, MF399, MF670, MF690. Industrials: 20D (fixed axle), 30E, 40E. MF-5-138

5 WHEELS AND ALES Replacement parts to fit Wheel Hub Assembly Front Wheel & Wheel Bolts 519278M91 Hub assembly, front wheel, 6-hole with cups (LM11910 & LM48510) & wear sleeves. Tractors: MF135, MF165, MF175, MF180, MF230, MF235 (except vineyard & orchard), MF245 (except vineyard & orchard), MF255 (prior to s/n 9A324145), MF265 (prior to s/n 9A324138), MF275 (prior to s/n 9A324136), MF1080, MF1085 (early production with 5-1/2" wide hub). Industrials: 20, 20C turf, 30 turf, 2135 (s/n 646002326 & up, s/n 9A50318 & up), using 6-hole hub, except narrow). Replaces hubs 183019M91, 194495M91, & 510771M93. Order 6-518611M1 hub bolts when replacing older hubs with new hub 519278M91. 535448M91 509893M91 834382M1 518611M1 Front wheel, with weight holes. 4:50 x 16, 6-bolt, 6" bolt circle with 4.62 pilot for 5:50 or 6:00 x 16 tires. 2500 lb. capacity. Same as TW450. Front wheel, with weight holes. 5.50" x 16", 6-bolt 6" bolt circle with 4.62" pilot for 7.50" x 16" tires. 3300 lb. capacity. Same as TW550. Front wheel, 8" x 16" 6-bolt, 6" bolt circle with 4.62 pilot. For rear wheel applications. Combines: 410, 510, 540, 550, 750. Hub bolts, front wheel, tapered, 9/16" x 1" threads, 1-9/16" total length. 898346M93 518611M1 194620M1 532781M92 Hub assembly, front wheel, 6-hole. For models with standard duty axles. Tractors: MF165, MF250, MF255, MF270, MF290, MF362, MF670, MF690. For models with heavy duty axles. Tractors: MF283, MF360, MF375, MF383, MF390, MF390T, MF393, MF398, MF399. Industrials: 20D, 20F, 30E, 30H, 40E. * Does not contain cups or cones Hub bolts, front wheel, tapered, 9/16" x 1" threads, 1-9/16" total length. Wear sleeve, front wheel hub, for 519278M91. Hub, front wheel. Tractors: MF255, MF265, MF275, MF285. 906863M1 181328M1 831420M1 Bolt, front wheel, tapered, 1/2" x 1" NF threads. For tractors: MF231, MF240, MF250 except Lo-profile, MF253; industrials: 20D turf or adjustable axle. Replaces 887135M1. Stud, hub, front wheel, 1/2" x 1-3/8" NF. Tractors: TE20, TO20, TO30, MF30, TO35, MF35, MH50, MF50, MF135, MF150, MF165, MF175, MF180, MF1080, MF1085. Stud, hub, front wheel, 1/2" x 1-1/2" NF, for 6-hole non-threaded front wheel hub. Tractors: MF65 utility, MF85, MF Super 90, MF250 (Lo-profile with 15" wheels), MF253 (with 179mm high axle), MF270, MF282, MF283, MF290, MF360, MF375, MF383, MF390, MF398, MF399, MF670, MF690, MF1100, MF1130. Industrials: 20D (except turf with fixed axle), 35 turf, 40E. Use with nut 195490M1. 195490M1 Nut, front wheel, 1/2" NF for front wheel stud 181328M1, 831420M1. MF-5-139

5 WHEELS AND ALES MF-FWL-1 Bolt Kit Bolt, front wheel bolt lug kit. Contains 6 special long 4140 chrome-moly heat treated bolts & 6 special heavy-duty 45 tapered shoulder nuts. Will not vibrate loose as originals do. Used on most MF tractors. Rear Wheel Rims and Bolts 535452M91 Power Adjust Rims, Clamp and Attaching Parts Power adjust rim, 10 x 28, 4 rail type. For double ramp clamp, holes in rail for stop body screw are drilled parallel to axle (not at angle). Use with stop body 503676M1, stop body screw 1751403M1, clamp 3615259M1, 1755057M2. 180863M91 535450M91 535454M91 828217M1 3534271 185400M2 180004M1 893017M2 184273M1 Rim, 10 x 28 demountable rim with 6 loop clamps. Painted aluminum. Rim, 11 x 28 demountable rim with 6 loop clamps. Painted aluminum. Rim, 12 x 24 demountable rim for 13 x 24 or 14 x 24 tires, with 6 loop clamps. Bolt, 5/8" x 2-7/8" NF, for rear wheel disc to rim. Tractors: MF25, MF130, MF240, MF250, MF2640, MF3630, MF3650. Industrials: 20D, 30E. Use with nut 3534271. Nut, 5/8"-18" x 1-1/16", use with rear wheel bolt 828217M1. Stud, rear wheel. Tractors: TO20, TO30, TO35, MF35 std., MF50, MF135 vineyard, MF150 std., MF235 std. & vineyard, MF245 std. & vineyard. 9/16" x 2" NF. Nut, rear wheel stud. 9/16" NF. Used with 185400M1 & 185400M2 stud. Stud, rear wheel. 5/8"-18 thread, 2.150" long. Tractors: MF35 & MF135 orchard, MF150 (row crop with planetary), MF235, MF245 orchard, MF255, MF265, MF275, MF165, MF175, MF180 (with wet or dry brakes). 5/8"-18 thread, 2.150" length. Nut, rear wheel. 5/8"-18 thread. For MF65 only. 503676M1 1751403M1 898021M1 Stop body, for power adjust rims 535452M91, 535453M91, & 1687615M91. Use with double ramp clamp 3615259M1 or 1755057M2. Replaces 227609M1. Screw, for stop body 503676M1. Use with power adjust rims 535452M91, 535453M91 & 1687615M91. Clamp, disc to rim. Double ramp type for power adjust rims 535452M91, 535453M91, & 1687615M91. For use on a wide range models. Tractors: TO35, MF35, MH50, MF50, MF65, MF90, MF135, MF150, MF165, MF175, MF180, MF184-4, MF230, MF235, MF240, MF245, MF250, MF253, MF255, MF265, MF275, MF282, MF285, MF360, MF362, MF375, MF390, MF390T, MF398, MF399, MF698, MF1080, MF1085, MF1100, MF1105, MF1130, MF1150, MF1155, MF1500, MF1505, MF1800, MF2675, MF2705, MF2745, MF2775, MF2805, MF4800, MF4840. Industrials: 30, 31, 40B. Replaces 3615259M1, 1755057M2. MF-5-140

6 HITCH AND HYDRAULICS Replacement parts to fit HLBMF61 HLBMF62 HLBMF63 1660373M92 181345M2 Leveling Box Assembly And Related Parts Leveling Box Assembly, standard right hand, category I, 20-1/2" closed, 26" open. Contains fork, shaft, pinion (185220M1-10-1/2"), housing, gear, bearing, handle & hardware. Replaces 677061. Services all catergory I standard models. Leveling box assembly, right hand. 23" closed, 27" open. Includes 14-5/8" shaft & pinion 897681M1 & fork 184358M1. For high clearance models. Tractors: MF50, MF65, MF150, MF165. Leveling box assembly, right hand. 21" closed, 25" open. Includes 12-9/32" shaft & pinion 8976680M2 & fork 184358M1. For low clearance models. Tractors: MF50, MF65, MF150, MF165. Leveling box assembly, Standard clearance, Cat II. 19" closed, 24-1/2" open. Contains fork, shaft, pinion, housing, gear, bearing, handle & hardware. Tractors: MF165, MF240. Industrials: MF20D Pinion gear, leveling box. Tractors: TE, TO, & MF prior to 1969. 897649M95 897649E-HD 893405M3 1861392M3 1860833M2 Heavy-duty leveling box assembly, right hand. 1" shaft & pinion 14-3/4" long. Tractors: MF65, MF165, MF175, MF265. Extra heavy-duty leveling box assembly, right hand. 1" shaft & pinion 14-3/4" long. Tractors: MF65, MF165, MF175, MF265. Fork, leveling box, heavy-duty, 12-3/4" long, for 1" shaft. Use with heavy-duty leveling box 897649M95. Tractors: MF65, MF165, MF175, MF265. Fork, leveling box, extra heavy-duty, 16-1/2" long, for 1" shaft. Used with extra heavy-duty leveling box 8907649E-HD. Tractors: MF65, MF165, MF175, MF265. Fork can also be used on tractors: MF185, MF275, MF283, MF285, MF375, MF383. Shaft & pinion, leveling box, 14-3/4" long, 1" shaft. For heavy-duty & extra heavy-duty leveling boxes 897649M1 & 897649EHD. Tractors: MF65, MF165, MF175, MF265. Left Hand Leveling Rod 195457M1 Thrust bearing, pinion shaft in leveling box. 180853M1 Knuckle, leveling box to lift arm. Tractors: TE, TO, & MF models using 3/4" offset. 182554M92 Lift link, left hand, non-adjustable. Hole centers 19-13/16". Tractors: TO35, MF35, F40, MH50, MF50, MF135, MF150. Industrials: 202, 204, 2135, 3165. 180860M1 1662382M1 Pin, knuckle to leveling box & knuckle to arm; 5/8" x 3". Crank handle, for leveling box assembly. 897661M1-HD Lift link, left hand, non-adjustable, heavy-duty. Hole centers 23-1/4", 24-1/4", 25-1/4". Tractors: MF135, MF150, MF230, MF235, MF245. Industrials: 20, 20C, 30, 202, 204, 2135, 3165. Replaces 897661M1. MF-6-141

6 HITCH AND HYDRAULICS Left Hand Rod And Yoke Assembly Lower Forks 890674M1 Fork, leveling box, 10-1/4" long, 3/4" NC thread. Tractors: TE20, TO20, TO30, TO35 (when used with 14" shaft). 897683M92 505801M91 Left hand rod & yoke assembly, 3/4" thread, 4-1/8" thread length, 14-7/8" long. Tractors: MF65, MF165, MF235 orchard, MF245 orchard, MF265, MF275 (low-profile with 16" rims). Left hand rod & yoke assembly, 1" thread, 4-1/4" thread length, 16-1/4" long. Tractors: MF150, MF175, MF180, MF265 (std. with 24" rims). Shafts With Leveling Gear 184358M1 Fork, leveling box, 1-1/2" across fork, 14-1/2" long, 3/4" NC thread. Tractors: TE20, TO20, TO30, MF35, MF135, MF150, MF65 (used in standard right hand assembly with 10-1/2" shaft), also left hand on MF65, MF230, MF231, MF235, MF240, MF245, MF250. Industrials: 20, 20C, 20D, 30E, 40E, 202, 204, 2135 (late production turf and utility), 3165. Also left hand fork on tractors: MF231, MF240, MF250; industrials: 20D, 30E, 40E. Lift Shaft Bushings 185220M1 897681M2 897680M2 Shaft & pinion, leveling box, 10-1/2" long, 3/4" NC thread. Tractors: TE20, TO20, TO30, MF35, MF135 (Used in standard RH assy. with 14-1/2" yoke). Shaft & pinion, leveling box, 14-5/8" long, 3/4" NC thread. Tractors: MF65 (hi-clearance), MF150 row crop, MF165 row crop. Industrials: 30, 40. Shaft & pinion, leveling box, 12-9/32" long, 3/4" NC thread. Tractors: MF65, MF235, MF245, MF265. 180896M91 181018M1 Bushing, hydraulic lift shaft; 2-3/8" O.D., 2" I.D., 3" long. Tractors: TE20, TO20, TO30. Bushing, hydraulic lift shaft. 2.36"O.D., 1.97"I.D., 1.39" long. Tractors: TO35, MF35, MF50, MF65, MF135, MF150, MF165. For shaft 184359M2, 4 required. Shaft 897567M3 uses bushing 1870934M1, not supplied by Tisco. Hydraulic Lift Parts Hydraulic Lift Arms 885444M91 1869289M91 Arm, hydraulic lift, right or left, 51-splines. Tractors: MF135, MF175, MF235, MF230, MF245. Industrials: 202, 203, 204, 205, 302, 304, 2135, 3165, 2200, 30, 20, 40, 40B 40C. Replaces 897575M1. Lower lift arm assembly. Category II. Tractors: MF135 (s/n 439191 & up), MF240. Industrials: MF20D. Right or Left. 36" hole centers. 184359M2 897567M3 Shaft, hydraulic lift, 37 splined end. Tractors: TO35, MF35, MF50. Early production tractors: MF135, MF150, MF165. Industrials: 35 turf, 2135 utility. Shaft, hydraulic lift, 51-splined end. Tractors: MF135, MF150, MF165 (late production). MF-6-142

6 HITCH AND HYDRAULICS Replacement parts to fit Hydraulic Lift Cover Gasket Set Hydraulic Lift Cylinder & Piston 829382M1 Cylinder, hydraulic lift, for 2-1/2" dia. piston. Tractors: TE20, TO20, TO30. Replaces 180884M1. LCRK2030 180881M1 180889M1 180897M1 181065M1 181067M1 181217M3 9N553 886549M2 181468M1 Gasket kit, lift cover repair. Tractors: TE20, TO20, TO30. Individual Gaskets Gasket, hydraulic lift cover. Tractors: TE20, TE-A20, TO20, TO30. Disc gasket for quadrant lever friction plate. 3" O.D., 9/16" I.D.,.175" thick. Tractors: TO20, TO30. Gasket, hydraulic lift cover to quadrant. Tractors: TO20, TO30. Gasket, pump base. Tractors: TE20, TO20, TO30. Gasket, valve chamber. Tractors: TE20, TO20, TO30. Gasket, inspection cover on differential case. Tractors: TE20, TO20, TO30. Gasket, hydraulic lift cylinder housing. Tractors: TE20, TE-A20, TO20, TO30. Gasket, hydraulic lift cover. Tractors: TO35, MF35, F40, MH50, MF50, MF65, MF150, MF165, MF175, MF180, MF230, MF235, MF245, MF255, MF265, MF275. Industrials: 20, 20C, 30, 30B, 30D, 31, 40, 40B, 50A, 50C. Gasket, pump base drain plug, also transmission filler plug. Tractors: TO20, TO30. 181983M1 180898M1 184443M91 830741M91 897564M1 897560M3 1665737M91 Piston, hydraulic lift, less rings. 2-1/2" dia. Tractors: TE20, TO20, TO30, TO35 (prior to s/n 179304), F40, MH50. Piston rings, hydraulic lift, 3 required, for 2-1/2" dia. piston. Tractors: TE20, TO20, TO30, TO35 (prior to s/n 179304), F40, MF50. Piston, hydraulic lift, includes rings, 3" dia. Tractors: TO35 (s/n 179304 & up), MF35, MF50, MF65. For early production tractors: MF135, MF150, MF165 using 3" dia. piston. Piston ring kit, 3" dia. 3 rings for 184443M91 piston, hydraulic lift. Tractors: TO35 (s/n 179304 & up), MF35, MF50, MF65. For early production tractors: MF135, MF150, MF165 using 3" dia. piston. Piston Rings, for 3-1/8" dia. hydraulic lift piston 897561M91, 3 required. These rings will not work on new style piston 1665737M91. Cylinder, hydraulic lift for 3-1/8" dia. piston. Tractors: MF135, MF150, MF165, MF230, MF235, MF240, MF245, MF250, MF282. Industrials: 20, 20C, 20D, 30, 30E, 40 202, 203, 204, 205, 302, 304, 2135, 3165. Use with 1665737M91 piston with rings. Piston, with rings, hydraulic lift, 3-1/8" dia. Tractors: MF135, MF150, MF165, MF230, MF235, MF240, MF245, MF250, MF255, MF265, MF282. Industrials: 20, 20C, 20D, 30, 30E, 40, 202, 203, 204, 205, 302, 304, 2135, 3165. Replaces 897561M91. MF-6-143

6 HITCH AND HYDRAULICS Quadrant Stop Kit Lift Arm Ends-Various Models QSK3FF Quadrant stop kit, includes wing nut and flat washer. Tractors: TE20, TO20, TO30. Economy Lower Lift Arms 184464M92 Lift arm end, category I, left hand, 7/8" pin hole. 180846M91 Lower lift arm, universal, less pin & chain. Tractors: TE20, TO20, TO30. Right or left. 32" hole centers. Forged Lower Lift Arm Assemblies 184463M92 SBA4613 184461M92 Lift arm end, category I, right hand, 7/8" pin hole. Lift arm end, right hand, Spee-Ball for 7/8" & 1-1/8" pins. Can replace 184461M92 & 184463M92. Tractors: MF65, MF85, MF150, MF165, MF175, MF180, MF265 & MF275. Lift arm end, right hand, category II, 1-1/8" pin hole. Tractors: MF65, MF85, MF88, MF Super 90, MF175, MF180, MF255, MF265, MF270, MF275, MF283, MF290, MF383, MF390, MF393, MF670, MF690. 30543E91 Lower lift arm with forged ball-joint ends, category I accomodates 7/8" drawbar or lower link pins. Universal arm for Massey Ferguson 180846M91 right or left. 32" hole centers. 184462M92 Lift arm end, left hand, category II, 1-1/8" pin hole. Tractors: MF65, MF85, MF88, MF Super 90, MF175, MF180, MF255, MF265, MF270, MF275, MF283, MF290, MF383, MF390, MF393, MF670, MF690. Lower Link Shafts 510584M92 191114M91 886428M1WC Lower lift arm, category I, universal right or left. Tractors: Late TO35, MF35, MF50, MF135, MF150. 33 hole centers, 5/8 thick. Lower lift arm, category I, with replaceable ball end & 7/8" ball other end, universal right or left. Tractors: Early TO35, MF35, MF50, MH50, F40. Industrials: 202, 204. Standard 31-1/2" hole centers, 5/8" thick. Lower Lift Arm Balls Lift arm ball, category I, use in 191114M91, 886431M1 & 1869289M91 lift arms. Tractors: MF135, MF240, MF250, MF20D, MF30. 181229M5 1867851M3 Pivot shaft for lower link. Threaded ends 5/8" NF & 5/8" NF, 5-1/4" OAL. Tractors: TO20, TO30, TO35, MF35, MF135, MF150. Industrials: 2135, 3165, 202, 204. Pivot shaft, for lower link, except Orchard & Vine. Threaded ends 5/8" NF & 3/4" NF, 6" OAL. Tractors: MF230, MF231, MF235, MF240, MF245. Industrials: 20, 20C, 20D, 30 turf. 886429M1WC Lift arm ball, category II ball, use in 191114M91, 886430M92 & 1862855M92 lift arms. Tractors: MF135, MF282. 1860936M1 Clip, lower lift arm, use with 191114M91, 886428M1 & 886429M1 lift arm balls. MF-6-144

6 HITCH AND HYDRAULICS Replacement parts to fit Lift Arm Repair End Lift Arm Lock Pin Kit Forged universal weld-on ends with ball joint. Repairs any lower arm. LLK65 Bushing kit, lift arm, contains 188148M1 bushing, 491105M1 spring & 2 each of 353957M1 screw & 188359M1 washer. Tractors: MF65, MF165, MF175, MF180. 30549E1 30550E1 Lift arm repair end, bent, forged. Category I, 7/8" pin hole, 1-3/4" width at weld end. 5-1/4" overall length. Lift arm repair end, bent, forged. Category II, 1-1/8" pin hole, 1-3/4" width at weld end. 5-1/2" overall length. B2226 Lower Lift Arm Weld-On Ball Joints Weld-on ball joint, 5/8" bore. Category 0. Lower Link Reducing Sleeves 30544E1 Lift arm ball joint, 7/8" bore. Category 1. 30545E1 Lift arm ball joint, 1-1/8" bore. Category 2. Converts Category II to Category I 30291E1 P2004 Bushing, lower lift arm. Category II to category I, 1-1/8" to 7/8", 1-3/4" long. Lower lift arm reducer bushing. Category II to category I, 1-1/8" O.D. to 7/8" I.D., 1-3/8" long. 30546E1 Lift arm ball joint, 1-7/16" bore. Category 3. Lift Arm Cuff SBJ2 Lift arm combination ball joint. For 7/8" or 1-1/8" pins. Category I & II. 1/4" thick race for light arms. TLAC65L Lift arm cuff, one piece formed, no welded seams. For lower lift arm. Replaces TLAC65. SBJ3 Lift arm combination ball joint. For 7/8" or 1-1/8" pins. Category I or II. 7/16" thick race for heavy lift arms. MF-6-145

6 HITCH AND HYDRAULICS Quality Forged Top Links and Repair Parts Replacement top links with bright plated 1-1/8" threaded forged ends. Available in category I & category II. 16" & 20" body centers are one piece with swedged ends. Has easy to use locking device with its own handle. Adjustment handle is conveniently placed through body center. 30108E91 Top link, 20" body, 1" category II ball joints. Adjusts 25" to 37". Painted red. 30105E91 Replacement top link, 16" body, 3/4" category I ball joints. Adjusts 20-1/2" to 29" overall. Painted red. JSA2024R Top link, 24" body, 1" Category II ball joints. Adjusts 29" to 41". Painted red. 30106E91 Replacement top link, 20" body, 3/4" category I ball joints. Adjusts 25" to 35" overall. Pained red. JSA2221 Top link end, 1-1/8" right hand thread. Category II, 1" pin hole. JSA1024R Top link, 24" body, 3/4" category I ball joints. Adjusts 29" to 39" overall. Painted red. JSA2222 Top link end, 1-1/8" left hand thread. Category II, 1" pin hole. JSA1200R Top link, 16" body combination Category II tractor & Category I implement ends, Adjust 19-1/2" to 29-1/2" overall. Painted red. Economy Forged Top Link and Repair Parts JSA1111 Top link end, 1-1/8" right hand thread, Category I, 3/4" pin hole. 30533E91 Forged, plated ends with 1-1/8" threads. Category I only. 16" center body is one-piece with swedged ends. Easy to use lever type locking device. Convenient adjustment handle through body center. Top link, 16" body, 3/4" category I ball joints. Adjusts 20-1/2" to 29" overall. Dichromate plated center body. JSA1111 Top link end, 1-1/8" right hand thread, Category I, 3/4" pin hole. JSA1112 Top link end, 1-1/8" left hand thread, Category I, 3/4" pin hole. JSA1112 Top link end, 1-1/8" left hand thread, Category I, 3/4" pin hole. 30107E91 Category II top links. 16" body, 1" category II ball joints. Adjusts 21" to 33" overall. Painted red. MF-6-146

6 HITCH AND HYDRAULICS Replacement parts to fit Heavy Duty Category II Top Link and Repair Parts Original Type Top Link Assemblies and Repair Parts Original type top links with forged 1-1/8" threaded dichromate plated ends. Available in category I, category II or category I & II. One piece bodies are available in 18-3/4" or 21-1/2" sizes. Adjusting handle folds away flush with body. Forged repelacement ends will fit original center tubes. 30109E91 Heavy duty top link, 16" body, 1" category II ball joints. Forged ends with 1-1/4" NC threads. Swedged steel center section. Adjusts 23" to 32" overall. Dichromate plated. 677197 Top link, category I, 1" threaded ends, 18-3/4" center tube, extends to 30-1/4". RE1717L Top link end, 1-1/4" left hand thread, category II, I" pin hole. 677198 Top link, category I, 1" threaded ends, 21-1/2" center tube, extends to 32-1/2". RE1718R Top link end, 1-1/4" right hand thread, category II, I" pin hole. 19875A91 Top link, category I by category II, 1" threaded ends, 21-1/2" tube, extends 32-1/2". 19876A91 Top link, category II, 1" threaded ends, 21-1/2" center tube, extends to 32-1/2". 183615M93 Top link end, 1-1/16" left hand threaded implement end; category II, 1" pin hole. MF-6-147

6 HITCH AND HYDRAULICS Weld-On Ball Joints 183623M93 Top link end, right hand threaded tractor end; category II, 1" pin hole. 30537E1 Ball joint, weld-on, 5/8" bore category 0. (A) 30538E1 Ball joint, weld-on, 3/4" bore, category I. (B) TL1218C Top link, category I & II ends. 18-3/4" center tube. Adjust from 23" to 30". 30539E1 30540E1 Ball joint, weld-on, 1" bore, category II. (B) Ball joint, weld-on, 1-1/4" bore, category III. (A) Top Link Reducer Bushings TL2018C Top link, category II both ends. 18-3/4" center tube. Adjust from 23" to 30". B80209 Bushing, category I to category 0, 1-5/8" long, 3/4" O.D. x 5/8" I.D. P2007 Bushing, category II to category I, 1-15/16" long, 1" O.D., 3/4" I.D. 183619M92 Top link end, 1-1/16" left hand threaded implement end; category I, 3/4" pin hole. Replaces 30115E91. 30290E1 Bushing, category III to category II, 2" long, 1-1/4" O.D., 1" I.D. Forged Weld-On Repair Ends 30541E1 Top link repair end. Category I 3/4" pin hole. 184079M91 Top link end, 1-1/16" right hand threaded, flat side, tractor end; category I, 3/4" pin hole. 30542E1 Top link repair end. Category II, 1" pin hole. MF-6-148

6 HITCH AND HYDRAULICS Replacement parts to fit Stabilizer Kits & Parts for TO Models, MF35, MF50 Stabilizer Kits & Parts for MF65, MF165, MF175, MF180 SK100 SK100HD Stabilizer kit for category I 3-point hitch, 31-1/2" hole spacing. Contains 2 arms, 2 brackets, 2 stabilizer pins with nut and lock washer, and 2 linch pins with chains. Tractors: TO20, TO30, TO35, F40, MH50, MF50. Stabilizer kit for category I, 3-point hitch, 31-1/2 hole spacing. Same as SK100 except contains 2-high alloy steel arms. SK65J SK65HCJ Stabilizer kit, low-clearance. Tractors: MF65, MF165, MF175, MF180. Contains 2 adjustable arms, right & left brackets, pins & hardware for mounting. Replaces 677172 & 677173. Stabilizer kit, high-clearance. Tractors: MF65, MF165, MF175, MF180. Contains 2 adjustable arms, right & left brackets, pins & hardware for mounting. Replaces 677187 & 677188. 181778M1 181778M1-HD SK100-33 SK100-33HD 190582M1 190582M1-HD 181775/776M1 181777M1-WNL 3534271 34811S36 DKPWCH Stabilizer arm for 3-point hitch, 31-1/2" hole spacing. Stabilizer arm for 3-point hitch, high alloy steel, 31-1/2" hole spacing. Stabilizer kit for category I 3-point hitch, 33" hole spacing. Contains 2 arms, 2 brackets, 2 stabilizer pins with nut & lock washer, & 2 linch pins with chains. Tractors: MF35, MF50, MF135, MF150, MF230, MF235, MF245. Stabilizer kit for category I 3-point hitch, 33" hole spacing. Same as SK100-33 except contains 2-high alloy steel arms. Stabilizer arm, 3-point hitch, 33" hole spacing. Stabilizer arm, 3-point hitch, high alloy steel 33" hole spacing. Stabilizer bracket. 3-point hitch, universal, left or right hand. Stabilizer pin with nut & lock washer. Nut, 5/8"-18 x 1-1/16" for 181777M1-WNL pin. Lock washer, 5/8" for 181777M1-WNL pin. Linch pin with ring & chain, 7/16" pin dia. x 1-5/8" long, 1-11/16" ring dia., DKP pin with safety chain. SK6756 SK150FA JSA1003 506799M1 193204M1 SKB62 SKB63 SKB67 SKB68 Stabilizer kit, standard-clearance. Tractors: MF65, MF165, MF175, MF180. Contains 2 adjustable arms, right & left brackets, pins & hardware for mounting. Replaces 677415 & 677416. Stabilizer kit, flat axle models. Tractors: MF150, MF165, MF175, MF180. Contains 2 adjustable arms, right & left brackets, pins & hardware for mounting. Stabilizer arm, complete with both ends. Adjustable from 27-1/2" to 37"; body length 23"; thread size 7/8"; pin holes 7/8". End only for JSA1003 stabilizer arm. 7/8" national fine left hand thread, 7/8" pin hole, 9-1/8" length, center of hole to end. End only for JSA1003 stabilizer arm. 7/8" national fine right hand thread, 7/8" pin hole, 8-7/8" length, center of hole to end. Stabilizer bracket, left hand for high-clearance tractors (SK65-HCJ). 6-1/2" drop-under axle. Stabilizer bracket, right hand for high-clearance tractors (SK65-HCJ). 6-1/2" drop-under axle. Stabilizer bracket, left hand for low-clearance tractors (SK65J). 3-1/2" drop-under axle. Stabilizer bracket, right hand for low-clearance tractors (SK65J). 3-1/2" drop-under axle. SKB69 Stabilizer bracket, right hand for standard clearance tractors (SK-6756 & SBK-3250). 3" drop-under axle. MF-6-149

6 HITCH AND HYDRAULICS SKB70 SKB150 Stabilizer bracket, left hand for standard clearance tractors (SK-6756 & SBK-3240). 3" drop-under axle. Stabilizer bracket, right hand or left hand for flat axle tractors. 5-1/2" drop-under axle. Linkage Pins Massey Ferguson replacement pins Stabilizer Kits for Industrial Tractors 30127E91 Top link pin. Category I, 3/4" pin dia., 2-7/8" useable length, 4-5/8" overall length. 30128E91 Top link pin. Category I, 3/4" pin dia., 3-7/8" useable length, 5-5/8" overall legnth. Replaces 195589M1. P2325 Top Link pin. Category II, 1" pin dia., 3-1/4" useable length 4-3/4" overall length. 30130E91 Top link pin Category II, 1" pin dia., 4-1/2" useable length, 6" overall length. Replaces P2450. SK-IND 539881M2TSK 514992M2 521006M1WN P7065 Stabilizer kit. Contains 4 mounting brackets with pins & 2-JSA5050 top links. Fits most 3-point hitches on light industrial models. Telescoping Stabilizer Stabilizer, telescoping arm, for 3-point hitch. Adjustable from 26" to 35". Tractors: MF250, MF251, MF253, MF255, MF261, MF265, MF270, MF275, MF283, MF285, MF290, MF298, MF360, MF375, MF383, MF390, MF390T, MF393, MF396, MF396T, MF398, MF399, MF670, MF690, MF698, MF1085. Bracket, used with telescoping stabilizer 539881M2TSK. Pin with nut, use with bracket 514992M2 & 539881M2TSK telescoping stabilizer. Stabilizer Pins Stabilizer pin. 5/8" fine threaded end, 7/8" pin end with 1/2" working area. Use nut 3534271 & 34811S36 lock washer. 195647M1 195589M1 180901M91 30131E91 30132E91 30133E91 P2006 30136E91 P2005 P7212 Top link pin Category I, 3/4" dia., 3" useable length, 4-5/8" overall length. Top link pin. Category I, 3/4" dia., 4" useable length, 5-5/8" overall length. Top link pin Category I, Hinged upper hitch pin assy. 3/4" dia., 9-5/8" useable length. Tractors: TO35, MF35, F40, MF50, MF65. Lower link pin. Category I, 7/8" pin dia. 1-3/4" useable length, 5-1/2" overall length, 7/8" thread dia. adj. jam nut. Replaces P2009. Lower link pin. Category I, 7/8" pin dia., 2" useable length, 6-3/16" overall length. 7/8" thread dia. adj. jam nut. Replaces P2009-L. Lower link pin. Category I, 7/8" pin dia., 1-3/4" useable length, 5-1/2" overall length, 7/8" thread dia. fixed shoulder. Replaces P2000. Lower link pin. Category II to I, 1-1/8" pin dia., 1-3/4" useable length, 5-1/8" overall length, 7/8" thread dia., adj. jam nut. Replaces 30135E91. Lower link pin. Category II to I, 1-1/8" pin dia., 2-1/4" useable length, 6-1/2" overall length, 7/8" thread dia. fixed shoulder. Replaces P6502. Lower link pin. Category II, 1-1/8" pin dia., 1-3/4" useable length, 6-1/4" overall length, 1-1/8" thread dia., adj. jam nut. Lower link pin. Category II, 1-1/8" pin dia., 2" useable length, 6-5/16" overall length, 1-1/8" thread dia., fixed shoulder. Replaces 30138E91. 668154M1-WNL Anchor pin with nut & lock washer. 7/8" dia., 3" overall length, 1" useable length, 5/8"-18 thread 1-3/16" thread length. MF-6-150

6 HITCH AND HYDRAULICS Replacement parts to fit Lower Stay Anchor Pin Kit For MF65 Drawbars 180485M1 Drawbar, category I, 7/8" pins. 11 holes, 26" bar length. PLSK65 186802M1 Stabilizer pin kit. Contains pin, bushing & special nut. Tractor: MF65. Stabilizer pin. Tractor: MF65. 180485M1HT DB212 Drawbar, heat treated, category I, 7/8" pins. 11 holes, 26" bar length. Drawbar, category II, 1-1/8" pins, 3" wide, 1-1/4" thick, 32" useable length, thirteen 3/4" dia. holes. Painted red. 491050M2 186809M1 Stabilizer bushing. Tractors: MF 65, MF180. Special hex nut, stabilizer pin. Tractors: MF65. Stay Chain & Clevis Kit DB214 Drawbar, category II, 1-1/8" pin, one piece, high carbon steel, 3" wide, 1-1/4" thick, 32" useable length, seven holes, 1-1/8" dia. Painted red. Drawbar Stay Arms 180861WP Stay chain & clevis kit, with pins. Tractors: TO20, TO30, TO35, MF35, MF50. 11-1/2" long. Clevis & Pin Kit DBSU DBSL Stay arm upper, 1/4" thick steel. Tractors: TE20, TO20, TO30. Stay arm lower, 1/4" thick steel. Tractors: TW20, TO20, TO30. Swinging Drawbar Assembly Kit includes drawbar, hanger & clevis assembly. 180333M1 Clevis, pin & cotter key, 2 of each. Tractors: TO20, TO30, TO35, F40, MF50. Clevis Eyebolt Assembly SDA6 SDA1 Swinging drawbar kit. Contains drawbar, hanger & clevis assembly. Tractors: TO20, TO30, TO35, MF50. Drawbar. 2" wide, 7/8" thick, 30-3/8" long. SDA2 Clevis assembly with pins, for SDA6. SDA3 Drawbar hanger. PT3 Pin for clevis assembly, 7/8" dia. CEK4 180856M91 Lift arm eyebolt kit. Contains eyebolt assembly with bushing & nut. Tractors: TO20, TO30, TO35, MF50. Eyebolt assembly, lift arm sway chain. Tractors: TO20, TO30, TO35, MF35, MF50. SDA75 SDA2-75 Swinging drawbar kit. Contains drawbar, hanger & clevis assembly. Tractors: MF35, MF50, MF65, MF135, MF150, MF165 (requiring 3/4" clevis studs). Clevis assembly with pin, for SDA75. 180859M1 Bushing, for lift arm eyebolt assembly 180856M1. MF-6-151

6 HITCH AND HYDRAULICS Pivot Pin For Swinging Drawbar Linch Pin Merchandiser 184630M1 3666341 Pivot Pin, for swinging drawbar. 1" O.D. by 1-7/8" working length. Fits original swinging drawbar 184611M1. Tractors: TO35, MF35, MH50, MF50, MF65, MF135, MF150, MF165, MF230, MF235, MF245, MF255. Industrials: MF20C, MF30B, MF40B, MF3165. Drawbar Bolt Bolt for swinging drawbar support, 3/4" 1-3/4" national coarse thread with special cone neck & grip lock adhesive. Tractors: MF135, MF150, MF165, MF175, MF180, MF230, MF235, MF245, MF255, MF265, MF275, MF285, MF298, MF698, MF699, MF1080. Industrials: 20, 20C, 30, 30B, 31, 40B, 50C. Replaces 3646621. Hitch Pins With Hair Pin Lock DKLP200 Linch pin merchandising display. Box of 200, DKLP-91, 7/16" dia. x 1-3/4" long, 1-5/8" dia. ring. Agricultural Implement Linch Pins DKLP91 Linch pin, 7/16" dia. pin x 1-3/4" useable length, 1-5/8" dia. ring. DKPWCH DKP1/4 DKP3/16 DKP-SD-1 Linch pin with ring & chain, 7/16" pin dia. x 1-5/8" long, 1-11/16" ring dia., DKP pin with safety chain. Linch pin, 1/4" O.D. pin x 1-1/4" long. Linch pin, 3/16" O.D. pin x 1-1/4" long. Linch pin, heavy-duty, 7/16" dia. pin, 1-7/8" useable length, 1-5/8" dia., extra heavy ring. P6254 P6256 Hitch pin, 5/8" x 4-1/2" useable length. Hitch pin, 5/8" x 6-1/4" useable length. Hydraulic Reservoir Dip Stick 30285E1 Hitch pin, 3/4" x 4-1/4" useable length. 30281E1 Hitch pin, 3/4" x 6-1/4" useable length. P8754 7/8" x 4-1/4" hitch pin. 30282E1 P1004 P1006 Hitch pin, 7/8" x 6-1/4" useable length. 1" x 4-1/4" hitch pin. Hitch pin, 1" x 6-1/4" useable length. 193400M1 Hydraulic oil level indicator. Tractors: TO20, TO30, TO35. Hydraulic Pump O-Ring Kit 894906M91 Hydraulic Pump O-Ring Kit, 26 pieces to repair or service hydraulic lift pump. Tractors: TO35, MF35. MF-6-152

6 HITCH AND HYDRAULICS Replacement parts to fit 181468M1 1683301M92 Gasket For Pump Base Drain Plug Gasket, pump base drain plug, also transmission filler plug. Tractors: TO20, TO30. Hydraulic Lift Pumps Hydraulic lift pump. 1.343" O.D. 21-spline shaft, for models with pressure control valve. Tractors: MF230, MF240, MF245, MF250, MF255, MF265, MF270, MF275, MF282, MF283, MF290, MF298, MF670, MF690, MF698, MF699. Industrials: 20C, 20D, 30, 30B, 30D, 30E, 31, 40, 40B, 50C, 50D, 50E. Replaces 1661616M94, 1672251M92, 1675125M92, 1675126M92, 1868439M98. 1684582M92 HPOK1 9N621KIT 181066M1 Hydraulic lift pump. Tractors: MH50, MF133, MF135, MF140, MF148, MF152, MF165, MF168, MF175, MF178, MF185, MF188, MF1200. Industrials: 20C, 50. Hydraulic Lift Pump Repair Parts Hydraulic pump overall kit. Contains cam blocks, pistons, chamber kits, PTO shaft bushing, relief valve, & gaskets. Tractors: TE20, TO20, TO30. Repair kit, hydraulic pump chamber. Tractors: TE20, TO20, TO30. Cam block, hydraulic pump. Tractors: TE20, TO20, TO30. 184473M93 Hydraulic lift pump assembly. 1-3/8" O.D. 10-spline shaft. Tractors: TO35 (s/n 179304 & up), MF35, MF50, MF65. Industrials: 203, 205, 202 & 204 work bull models. 890675M1 Piston, hydraulic pump. Tractors: TE20, TO20, TO30. 3790722M1 Hydraulic pump, Tandem main pump, single stage. Tractors: MF2640, MF2675, MF2705, MF2745, MF2775, MF2805, MF3505, MF3525, MF3545, MF3630, MF3645, MF3650, MF3655, MF3660, MF3670, MF3680, MF3690, MF8120, MF8140, MF8150, MF8160. Replaces 3038730M1, 3038730M2. 181095M1 Bushing, hydraulic pump base, for PTO shaft. Tractors: TE20, TO20, TO30. 3774612M91 Hydraulic auxilary tandem pump. Tractors: MF174F, MF184F, MF194F, MF362, MF374S, MF374F, MF375, MF382, MF383, MF384S, MF390, MF390T, MF394S. Replaces 3597420M91, 3595202M91, 3597692M91, 3597706M91, 3701005M91. 3774613M91 Hydraulic auxilary pump. Tractors: MF396, MF399 (ENGINE 1006.6). Replaces 3701006M91, 3611854M91. MF-6-153

6 HITCH AND HYDRAULICS Hydraulic Lift Pump Repair Kits Valve Chamber Repair Kit HPOK3WCB HPOK2WCB Hydraulic pump overhaul kit. Contains valve chamber assemblies, pistons, piston rings & cam blocks. Tractors: TO35 (s/n 179304 & up), MF35, MF50 (s/n 526837 & up), MF65, MF135, MF165 using 190799M1.91 diameter piston. Hole sizes: (B) 3/8" 9.5mm; (C) 7/16" 11.1mm; (D) 15/32" 11.9mm. Hydraulic pump overhaul kit. Contains valve chamber assemblies, pistons, piston rings & cam blocks. Tractors: MF135, MF150, MF165 (using.98 diameter piston), MF175, MF180. Hole sizes: (B) no hole; (C) 33/64" 13.1mm; (D) 3/8" 9.5mm. 830997M91 Chamber repair kit, hydraulic pump valve. Contains valves, springs, snap rings & o-rings to repair all 4 chamber ports in one tractor. Services 180920M1 & 180921M1 body on early TO35. Tractors: TO35, MF35, MF50, MF65, MF135, MF150, MF165, MF175, MF180. Hydraulic Pump Valve Chamber Assemblies HPOK3LCB HPOK2LCB 180924M2 Hydraulic pump overhaul kit. Contains valve chamber assemblies, pistons, & piston rings. Tractors: TO35 (s/n 179304 & up), MF35, MF50 (s/n 526837 & up), MF65, MF135, MF165 (using 190799M1.91 diameter piston). Hole sizes: (B) 3/8" 9.5mm; (C) 7/16" 11.1mm; (D) 15/32" 11.9mm. Hydraulic pump overhaul kit. Contains, valve chamber assemblies, pistons, & piston rings. Tractors: MF135, MF150, MF165 (using.98 diameter piston), MF175, MF180. Hole sizes: (B) no hole; (C) 33/64" 13.1mm; (D) 3/8" 9.5mm. Cam Blocks, Hydraulic Pump Cam block, front, hydraulic lift pump, with lip. Tractors: TO35, MF35, MF50, MF65, MF135, MF165, MF175, MF180. Supersedes & replaces 894607M1. 184471M1VA 831519M1 1868435M3VA Hydraulic pump valve chamber assembly. Contains valves, springs, plugs, o-rings, & snap rings installed. Tractors: TO35 (s/n 179304 & up), MF35, MF50 (s/n 526837 & up), MF65, MF135, MF165 using 190799M1.91" diameter piston. Hole sizes: (B) 3/8", 9.5mm. (C) 7/16", 11.1mm. (D) 15/32", 11.9mm. O-ring, hydraulic pump valve chamber to pump body, 1/6" x 7/16" I.D. (9 required). Hydraulic pump valve chamber assembly. Contains valves, springs, plugs, o-rings, & snap rings installed. Tractors: MF135, MF150, MF165 using.98" diameter piston; MF175, MF180. Hole sizes: (B) no hole. (C) 33/64", 13.1mm. (D) 3/8", 9.5mm. 180925M2 Cam block, rear, hydraulic lift pump, without lip. Tractors: TO35, MF35, MF50, MF65, MF135, MF165, MF175, MF180. Supersedes & replaces 894608M1. MF-6-154

6 HITCH AND HYDRAULICS Replacement parts to fit Hydraulic Pump Pistons, Rings Lift Pump Control Valves 189427M92 Valve assembly, hydraulic pump control. Tractors: MF35, MF50, MF65. 897507M92 Valve assembly, hydraulic pump control. Tractors: MF135, MF150, MF165, MF175, MF180. 181043M1 190799M1 892604M1 Piston, hydraulic lift pump. Tractors: TO35 (prior to s/n 179303), MF50 (prior to s/n 516836, using.80" diameter piston). No rings required. Piston, hydraulic lift pump. Tractors: TO35 (s/n 179304 & up), MF35, MF50 (s/n 568747 & up), MF65, MF135 & MF165 (using.91" diameter piston). Supersedes & replaces 184470M1. Piston ring,.91" dia. hydraulic lift pump, 2 required on piston 190799M1. Supersedes 190848M1. 1862486M96 3590021 Valve assembly, conversion service kit, hydraulic pump control. Contains valve 1862488M93, plus components to convert & replace 897507M92 in early production. Tractors: MF135, MF150, MF165, MF175, MF180. O-ring, for lift pump control valves, 3/32" x 3/4" I.D. For use with 189427M92 & 897507M92. 1860038M1 897493M1 1000251M1 Piston, hydraulic lift pump. Tractors: MF135, MF150, MF165 (using.98" diameter piston), MF175, MF180. Piston ring,.98" dia. hydraulic lift pump, 2 required on piston 1860038M1. Needle Bearing For Hydraulic Lift Pump Needle bearing, for recess in rear of camshaft for hydraulic lift pump. B108 bearing,.625" I.D.,.812" O.D.,.500" wide. Tractors: TO35, MF35, MH50, MF50, MF65, MF135, MF150, MF165, MF175, MF180, MF230, MF231, MF235, MF240, MF245, MF250, MF253, MF255, MF265, MF270, MF275, MF282, MF283, MF285, MF290, MF298, MF360, MF375, MF383, MF390, MF390T, MF398, MF399, MF670, MF690, MF698, MF699, MF1080, MF1085. Industrials: 20, 20C, 20D, 30, 30B, 30D, 30E, 31, 35, 40, 40B, 40E, 50C, 50D, 50E, 202, 203, 204, 205, 302, 304, 2135, 3165. 1681789M91 Control valve, hydraulic lift pump, with collar & retainer. Tractors: MF231, MF240, MF250, MF255, MF265, MF270, MF275, MF290, MF298, MF360, MF365, MF383, MF390, MF393, MF399, MF670, MF690, MF698, MF699. Industrials: 20D, 30, 30B, 30D, 30E, 40B, 40E, 50C, 50D, 50E. Also for lift pumps on the following models except MKII pumps/pumps with rear mounted safety valve. Tractors: MF230, MF235, MF245. Industrials: 20C, 31, 40. Replaces 1870763M91. MF-6-155

6 HITCH AND HYDRAULICS Safety Relief Valves Hydraulic Front Pump 181087M91 883402M92 884747M93 831452M1 531607M93 886821M94 Relief valve, hydraulic pump. Tractors: TO20, TO30. Relief valve, hydraulic pump, 2550 psi. Tractors: TO35, MF50, MF65, MF135, MF150, MF165, MF175, MF180. Relief valve, hydraulic pump, 2750 psi. Tractors: MF30, MF135, MF150, MF165, MF175, MF180, MF235, MF255. O-ring for relief valves. Auxiliary Hydraulic Pump Auxiliary hydraulic pump assembly. Tractors: MF165, MF175, MF180, MF235, MF240, MF245, MF250, MF253, MF255, MF265, MF270, MF275, MF283, MF285, MF290, MF298, MF670, MF690, MF698, MF699, MF1085. Industrial: 30. Replaces 516260M93, 526099M93, 1663627M92, 1675136M91, 1686765M91, 1686766M91. Hydraulic pump assembly, less auxiliary hydraulic system. Tractors: MF135, MF150, & MF165 with rear axle s/n C5051 & up. MF175, MF235, MF240 (s/n 2773 NO1001 & up), MF245, MF255, MF265. Industrials 20C, 30, 30E, 31, 40B, 50C, 50D, 50E (with independent PTO). L827-10-LB Hydraulic pump, less bracket. 14 GPM @ 2000 RPM. Can replace 706105M91 by changing the in & out plumbing. SAEA mounting. 3-1/4" pilot, 4-3/8" bolt spacing on 2 bolt flange. 2750128M91 3790722M1 Pump, hydraulic front mount for backhoes, crawlers, forklifts, & loaders, 7/8" 13-spline shaft. 21.5 GPM at 2000 rpm. Tractors: MF30, MF32, MF32A, MF34A, MF34B, MF40, MF52, MF54, MF100, MF200, MF212, MF225, MF235, MF400C, MF2200, MF2244, MF2500, MF4500, MF6500. H10190RF210RM adapter included. Hydraulic pump, Tandem main pump, single stage. Tractors: MF2640, MF2675, MF2705, MF2745, MF2775, MF2805, MF3505, MF3525, MF3545, MF3630, MF3645, MF3650, MF3655, MF3660, MF3670, MF3680, MF3690, MF8120, MF8140, MF8150, MF8160. Replaces 3038730M1, 3038730M2. MF-6-156

6 HITCH AND HYDRAULICS Replacement parts to fit L601-14 Pump Drive Couplers for Loader Backhoes L601-9 Pump Drive Couplers for Loader Backhoes L601-14 Coupler complete, Morflex series 302. Contains center member, 2 drive flanges with set screws, & 4 bolts with lock nuts. 1752218M91 Center member for L601-14, 3-1/8" dia., four 1/4" holes, 1-15/16" spacing. Same as L51-27. L601-9 Coupler complete, Morflex series 352. Contains center member, 2 drive flanges with set screws, & 4 bolts with lock nuts. 1753729M91 Center member for L601-9, 3-5/8" dia., four 5/16" holes, 2-1/4" spacing. Same as L52-10. 1752219M91 Z80507 Drive flange for L601-14, 3/4" round bore with set screw 1/4" x 3/8". 1-15/16" spacing. Same as L36-3. Capscrews for L601-14, 1/4"-28 x 1-1/2", Gr 5, hex head. 1753730M1 Drive flange for L601-9, 3/4" round bore with set screw 1/4" x 3/8". 2-1/4" spacing. Same as L36-7. L80-7 Capscrews for L601-9, 5/16"- 24 x 1-5/8", gr 5 hex head. H61-16 Self locking hex nuts for L601-14, 1/4"-28. L61-2 Self locking hex nuts for L601-9, 5/16"-24. L36-4 L36-5 Optional drive flange for L601-14, 5/8" round bore with set screw 1/4" x 3/8" #SSH4-6. 1-15/16" spacing. Optional drive flange for L601-14, 7/8" round bore with set screw 1/4" x 3/8" #SSH4-6. 1-15/16" spacing. L36-6 L36-8 Optional drive flange for L601-9; 5/8" round bore with set screw 1/4" x 3/8" #SSH4-6. 2-1/4" spacing. Optional drive flange for L601-9; 7/8" round bore with set screw 1/4" x 3/8" #SS4-6. 2-1/4" spacing. L36-19 Optional drive flange for L601-9; 1" round bore with set screw 1/4" x 3/8" #SS4-6. 2-1/4" spacing. L78-13 Optional drive flange for L601-9, 13-spline for 7/8" dia. shaft 5/16" dia. bolt holes 2-1/4" on center. MF-6-157

6 HITCH AND HYDRAULICS 704812M93 708639M91 1400022M91 704997M92 708574M92 Adapter Plates & Drive Shafts For front mounted hydraulic pumps. Adapter plate, for front mounted hydraulic pump drive. 5-1/4" dia. with 3 bushings, mounting holes 3.465" on center, 4" bolt circle, 3/4" left hand threaded center hole. Tractors: MF35, MF150, MF65, MF135, MF150, MF235 orchard, MF245 orchard. Industrials: 20, 20C, 30, 30B, 30D, 35, 40, 50, 202, 203, 204, 205, 2135, 2200. Adapter plate, for front mounted hydraulic pump drive. 5-1/4" dia. with 4 bushings, mounting holes 2.835" on center, 4" bolt circle, 7/8" left hand threaded center hole. Tractors: MF135 orchard, MF165, MF175. Industrials: 30, 40B, 50A, 50C, 50D, 2200, 3165. Bushing for front mount hydraulic adapter plates. Tractors: MF35, MF50, MF65, MF135, MF150, MF165, MF175, MF235 orchard, MF245 orchard. Industrials: 20, 20C, 30, 30B, 30D, 35, 40, 40B, 40E, 50, 50A, 50C, 50D, 202, 203, 204, 205, 2135, 2200, 3165. Used in adapter plates 704812M93 & 708639M91. Drive shaft with coupler attached. For front mounted hydraulic pump drive, 11-3/8" overall length, adapter end 3/4" left hand threads, coupler end 3/4" round bore with 3/16" keyway. Tractors: MF135 orchard. Industrials: 20, 35 utility, 202 (s/n 303158 & up), 203, 204 (s/n 303158 & up), 205, 2135. Drive shaft with coupler attached. For front mounted hydraulic pump drive, 11-5/8" overall length, adapter end 3/4" left hand threads, coupler end 7/8" 13-splines. Industrials: 40. 707166M92 190495M93 729566M91 521451M1 191855M4 Drive shaft with coupler attached, for front mounted hydraulic pump, 14-1/8" overall length, adapter end 7/8" left hand threads, coupler end 7/8" 13-splines. Tractors: MF165, MF175. Industrials: 30, 3165. Drive shaft with coupler attached, for front mounted hydraulic pump. 15-1/2" overall length, adapter end 7/8" left hand thread, coupler end 7/8" 13-splines. Industrials: 40B, 50A. Drive shaft with coupler attached, for front mounted hydraulic pump, 15-7/8" overall length, adapter end 7/8" left hand threads, coupler end 7/8" 13-splines. Industrials: 50C, 50D. Hydraulic Lift Pump Filter Element Filter element for hydraulic lift pump, top mount. 2-7/16" O.D. 1-29/32" I.D. & 4" long. Tractors: MF35, MF50, MF65, MF85, MF88, MF90, MF1080. Industrials: 202, 203, 204, 205, 302, 304, 2135, 2200, 3165. Also for models with pumps having 10-spline camshaft. Tractors: MF135, MF150, MF165, MF175, MF180. Industrials: 20, 30, 31, 40, 302, 304. Filter, hydraulic oil cooler, multi-power transmission. Tractors: Super 90, MF135, MF165, MF175, MF180, MF1080, MF1100, MF1130. Industrials: 30, 30B, 30E, 40, 50A, 50E, 50F, 204, 205, 302, 304. 729563M91 Drive shaft with coupler attached, for front mounted hydraulic pump drive, 12-3/8" overall length, adapter end 3/4" left hand threads, coupler end 7/8" 13-splines. Industrials: 20C, 30B, 30D. MF-6-158

6 HITCH AND HYDRAULICS Replacement parts to fit Hydraulic Oil Filter Assembly Break-Away Clamps 1042326M91 1051689M1 Oil filter assembly, hydraulic, with 25 micron element, 20 gallon per minute spin-on filter with in-line mounting head having 3/4" ports. Head has by-pass feature set at 15 psi. Rated at 200 psi. Same as SF1-25. Oil filter element, hydraulic, 25 micron. Used on 1042323M91. Same as 1A9023. Loader/Backhoe Cylinder Packing Kits 5001-4 Break-away clamp, single, hydraulic. 1900970M91 S42-4 252788M1 Break-away clamp, double, hydraulic (5006-4). Break-away clamp, double, hydraulic. For use with S20-4 & S40-4 couplers. Quik-cover assembly HV4957 fits this clamp. Dust Covers Rubber plug with chain & ring. For Pioneer hydraulic couplers (5205-4) 835690M92 Loaders: 200 (lift cylinder and self leveling). Pioneer Hydraulic Couplers External Hydraulic Valve - Single Spool 1086692M91 Quick coupler, hydraulic, female body half, 1/2" NPT. Same as 4050-4. 242678M1 Quick coupler, hydraulic, male tip half, 1/2" NPT. Same as 8010-4. 1026699M92 8010-15 Quick coupler, hydraulic, female body half, 3/4"-16 SAE. Same as 8250-15. Quick coupler, hydraulic, male tip half, 3/4"-16 ORB thread, 2500 PSI. 1-1/16" hex size. Converts tractor for operation of cylinders on pull type implements, front loaders, hydraulic motors, or other optional external hydraulics. Single spool, double acting control valve mounts conveniently on flat or shell fenders. Selector/isolator allows operation of single or double acting cylinders. Mounting hardware & instructions included. For all TO35 & later Massey Ferguson models where 182373M1 lift cover plate is accessible. 8250-4 Quick coupler, hydraulic, female body half, 1/2" NPT. Couples under pressure from both sides. TS3200M External hydraulic valve kit, single spool, double acting control valve. Contains isolator valve, valve, couplers, clamp, hoses, adapters, hardware, & instructions. MF-6-159

6 HITCH AND HYDRAULICS Selector/Isolator Assembly Combination one-way or two-way isolator-selector allows single acting or double acting external hydraulic service. TS300 Selector/isolator assembly. For TO35 & later tractors thru MF1080, without individual external hydraulic systems. Three-position spool, forward position allows one-way (push) for single acting cylinder. Center position allows operation of the 3-point arms, & the rear position will feed power to a 4-way control valve for two-way (push-pull) operation of double acting cylinder. Fits all MF tractors where 182373M1 lift cover is used. Remote Hydraulic Valve Kit Application: Massey Ferguson Tractors TO35 thru MF1080. Note: Coupler kits must be ordered separately, to provide quick-couplers and hoses for the third spool of this valve. HV4298 Replaces S42-4 S20-4 5205-4 H31-SPL-44 Coupler kit for TISCO 4000 series valves. Description Qty in HV4298 CLAMP 1 COMPLETE COUPLER 2 DUST PLUG 2 HYD HOSE ASSY 2 MF-6-160

6 HITCH AND HYDRAULICS Replacement parts to fit HV4000 Series Remote Hydraulic Valve Kits Application: For TO35 to MF1080 models originally equipped with a 182373M1 two-bolt manifold plate (transfer cap) at top of hydraulic system. This plate is located just forward of the operator s seat on top of the hydraulic top cover. Major Sales Features: Isolator selector is installed in place of the manifold plate. Select either internal or external system operation-not simultaneous operation. Installation is quick, clean & simple. Valve can be installed in any convenient location on tractor fender or inside wall of cab. Kit contains all hoses & couplers for all spools. Improved quick couplers allow one hand hook up of hydraulic cylinder hoses (Safeway S40-4 coupler). Hydraulic coupling plugs. HV4211 HV4220 HV4221 Replaces S42-4 S40-4 5205-4 HV4970 HV4971 HV4972 HV4973 HV4012 HV4020 HV4021 TS300 Single spool hydraulic valve kit. Contains a 1 spool valve with handle, selector valve, quick-coupler (female half), break-way clamp, dust plugs, and hoses. Double spool hydraulic valve kit. Contains a 2 spool valve with handles, selector valve, quick-coupler (female half), break-way clamp, dust plugs, & hoses. Double spool hydraulic valve kit with one float spool. Contains a 2 spool valve with handles, selector valve, quick-coupler (female half), break-way clamp, dust plugs, & hoses. Description CLAMP COMPLETE COUPLER DUST PLUG HYD HOSE ASSY HYD HOSE ASSY HYD HOSE ASSY HYD HOSE ASSY HYDRAULIC VALVE KIT HYDRAULIC VALVE KIT HYDRAULIC VALVE KIT ISOLATOR VALVE Qty in HV4211 1 2 2 1 1 1 1 1 0 0 1 Qty in HV4220 2 4 4 2 2 1 1 0 Special Hose Assemblies 1 0 1 Qty in HV4221 2 4 4 2 2 1 1 0 0 1 1 Replaces HV4970 HV4971 HV4972 HV4973 H31-SPL-32 H31-SPL-36 H31-SPL-44 292838 HOSE TYPE 3/8" - 1 wire 3/8" - 1wire 3/8" - 1 wire 3/8" - 1 wire 3/8" - 1 wire 3/8" - 1 wire 3/8" - 1 wire 3/8"-1 wire HOSE END LEFT 9/16" - 18 ORB 90 Male Swivel 9/16" - 18 90 ORB Male Swivel 9/16" - 18 ORB 90 Male Swivel 9/16" - 18 ORB 90 Male Swivel 9/16" - 18 ORB 90 Male Swivel 9/16" - 18 ORB 90 Male Swivel 9/16" - 18 ORB 90 Male Swivel 3/8" NPT 90 Male Swivel OVERALL LENGTH (IN) 18" 21" 30-1/2" 32-1/2" 32" 36" 44" 24" HOSE END RIGHT 1/2" NPT Male Solid 1/2" NPT Male Solid 3/8" NPT Male Solid 3/8" NPT Male Solid 3/8" NPT Male Solid 1/2" NPT Male Solid 1/2" NPT Male Solid 1/2" NPT Female Solid MF-6-161

6 HITCH AND HYDRAULICS Hydraulic Valve Replacement Handles and Parts HV4988 Handle, offset, used in HV4984 & HV4985 valve assemblies. HV4989 Handle, straight. Used in HV4984 and HV4895. 19833A92 Hydraulic valve, 3-spool, 3/4" ORB work points, with manifold & two elbows. For tractors: MF35 & later models thru MF1080. This valve allows operator to use auxiliary hydraulics & 3-point lift at the same time without switching valves. Valve mounts underneath the seat, some tractors may require slight seat modification. Control Valves For External Hydraulic Kits HV4990 HV4998 HV4999 HV4987 Handle, hydraulic valve, for 4000 series valve. 90 degree short angle. Handle, hydraulic valve, for 4000 series valve. 70 medium angle. Handle, hydraulic valve, for 4000 series valve. 45 long angle. Knob, hydraulic valve handle, for 4000 series valve. HV4975 Link kit, hydraulic valve handle, for 4000 series valve. TS200BA Valve for TS3200M. Single spool, 4-way, 3-position, spring loaded to neutral. No relief valve, no power beyond option. In & out ports 3/4", work ports 1/2" NPT. MF-6-162

6 HITCH AND HYDRAULICS Replacement parts to fit HV4000 Series Hydraulic Valves One Spool Valves HV4000 Valve Components HV4910 Handle kit for 4000 series hydraulic valve. Includes handle & mounting hardware. HV4911 Handle mounting kit for 4000 series hydraulic valve, includes bail & hardware for mounting the HV4910 standard handle. HV4010 HV4012 Valve, hydraulic, with handle, single spool, 2000 psi. relief, tandem (4-way) spool, spring center to neutral. Valve, hydraulic, with handle, single spool multi-valve. NO RELIEF, tandem (4-way) spool, convertible to 3-way, spring center to neutral, with 90 rotated handle. Two Spool Valves HV4917 HV4916 90 Handle kit for 4000 series hydraulic valve, includes handle & mounting kit with hardware. Has special bracket used for 90 rotated handle. 90 Handle mounting kit for 4000 series hydraulic valve, includes hardware for mounting the HV4917 90 handle kit. Replaces HV4913. HV4923 Spool seal kit for 4000 series hydraulic valve, front & rear spool sealing o-rings. HV4020 HV4021 Valve, hydraulic, with handles, two spool, 2000 psi. relief, tandem (4-way) spools, spring center to neutral. Valve, hydraulic with handles, two spool, 2000 psi. relief, one spool tandem (4-way) float position with spring center to nuetral & one spool tandem (4-way) spring center to neutral. Three Spool Valves HV4930 HV4931 Float spool detent kit for 4000 series hydraulic valve. Contains all parts needed to convert standard spool to a float spool. Standard spring center kit for 4000 series hydraulic valve. Kit contains all parts needed to repair or convert existing spool. *Note: On any two spool valve, only one spool can be equipped with a float detent. HV4030 HV4034 Valve, hydraulic, with handles, three spool, 2000 psi. relief, all spools tandem (4-way) spring center to neutral. Hydraulic valve, three spool, less handles. 2000 psi relief valve, one spool 3-way spring centered with one position detent. Two spools 4-way spring center to neutral. HV4932 Three position detent kit (no spring) for 4000 series hydraulic valve. Any tandem action spool can be converted to detent using this kit. Spool will remain in detent position until physically moved to neutral. NOT A PRESSURE RELEASE DETENT KIT. MF-6-163

6 HITCH AND HYDRAULICS HV4000 Series Hydraulic Valves HV4940 HV4941 Power beyond plug kit for 4000 series hydraulic valve. Can be installed in place of allen head plug in side of valve casting. Allows plumbing additional hydraulic control valve into system. Closed center plug kit for 4000 series hydraulic valve. Can be installed in place of allen head plug in side of valve casting. Allows use of valve with closed center hydraulic system (such as MF1100 series with variable displacement hydraulic pump). MF-6-164

6 HITCH AND HYDRAULICS Replacement parts to fit Hydraulic Top Link Cylinders Standard Tisco cylinders, all ports 9/16"-18 ORB with two adapters 9/16"-18 ORBM x 1/4" NPTM 90 degree swivel. HTL2101-2" bore for MF40 HTL3102-3" bore for standard category II replacement on most US tractors to 80 hp HTL3103-3" bore for MF50E HTL3106-3" bore for industirals 20C and 206. Replaces HTL2101 HTL3102 HTL3103 HTL3106 Equiv. Gannon 13-535 ** 13-827 * STROKE LENGTH 8" 8" 8" 8" CLOSED LENGTH A 24-1/16" 21" 26" 20" BARREL LENGTH B 12-7/16" 12-7/16" 12-7/16" 12-7/16" ROD HOLE DIA. C 3/4" 1" 1" 3/4" ROD END WIDTH D 1-3/4" 1-3/4" 1-3/4" 1-3/4" BASE END DIA. E 3/4" 1" 1" Hydraulic Side Link Cylinders Standard Tisco cylinders. All ports 9/16" 18 ORB with two adapters 9/16" - 18 ORBM x 1/4" NPTM swivel. 3/4" BASE END WIDTH F 1-3/8" 1-3/4" 1-3/4" 1-3/8" BASE TO BALL C/L 7-9/16" 2-1/2" 5-1/2" 3-1/2" HSL3203-3" bore for MF50C. Replaces HSL3202 EQUIV. GANNON 13-560 STROKE LENGTH 4" A1 A2 A3 23" BARREL LENGTH B 8-7/16" Hydraulic Cylinder Seal Kits CLEVIS DEPTH C 3/4" CLEVIS WIDTH D 3/4" BASE END DIA. 3/4" BASE END WIDTH 2" BASE TO BALL C/L 3" HSK2002 Seal kit, for 2" bore HTL & HSL series top & side link cylinders. Contains seals & o-rings for 2" cylinder repair. For cylinders HTL2101, HTL2102, HTL2103, HSL2201, HSL2202, HSL2203. Replaces HSK2001. HSK3002 Seal kit, for 3" bore HTL & HSL series top & side link cylinders. Contains seals & o-rings for 3" cylinder repair. For cylinders HTL3101, HTL3102, HTL3103, HSL3201, HSL3202, HSL3203. Replaces HSK3001. MF-6-165

7 FORAGE AND HARVESTING Sickle Assemblies Application Sickle Mower: 41, 51, 135 581177M92 (s/n 181008100 & up) Welded Gear Box Mower Conditioner: 925 683583M91 Power Cut 1/4" x 7/8" 802-016K Knifeback Replaces Part RIVETED/BOLTED TYPE OF No. SECTION SECTION Riveted Riveted BOLTED "Big Tooth" Sickle Section Designed to last longer and stay sharper than ordinary sickle sections. Ideal for coarser, dryer stem crops (10 serrations per inch). H, US, CR H, US H TS CR LENGTH (FT) 7' 9' 16' INCLUDES NUMBER HEAD NUMBER OF SECTIONS 581387M1 28 683879M1 Headless 37 66 Universal Chrome End Sections Replaces Section Part No. 669807M1 683937M1 622-011K Eliminates dead space at end of cutter bar & prevents clogging. Every 2-pack card of 2US-PK & 3TS-PK has mounting instructions printed on the reverse side. Sections are priced & sold by the piece, but shipped in package multiples only. If sections are packaged 10 per box, please order in multiples of 10 sections (10, 20, etc.). If sections are packaged 2 sections per card, please order in multiples of 2 sections (2, 4, etc.). 146503M2BT Big Tooth section, 10 serrations per inch. H TS CR, 3" x 3-1/4", 2" hole spacing. Used with rigid header #1859. Combines: 510, 540, 550, 750, 850 (prior to s/n 1696027543), 860 (prior to s/n 174619114). Can replace 146503M2. 1071707M1BT Big Tooth section, 10 serrations per inch. H TS plain, 3" x 3-1/4". Windrowers: 885 (with auger header). 1S-B Smooth end section, chrome, heavy- duty. Packaged 10 sections per box. Replaces 1SG. 3TS-PK Topserrated end section, chrome, heavy-duty. Packaged 2 sections. Replaces 3TSG. MF-7-166

7 FORAGE AND HARVESTING Replacement parts to fit Sickle Sections 3" x 3-1/4" Windrowers: 885 (with auger header) 1071707M1 -hvy gauge, top serrated, plain finish, uses RIV101. 3" x 3-1/4" Mowers: 30, 31, 32, 51, 52, 71, 135, FEO, MH5, MH6 (1940 & up) 1053209M1 141198CR 141113 3" x 2-1/2" Combines with wobble drive. Floating cutter bar on combines: 750 & 760 (s/n 174600413& up) -Hvy. gauge, Top serrated, Chrome finish, uses CR8-5 rivet. For use on combines with wobble drive & floating cutter bars. 3" x 3" Combines: 35, 60, 72, 80, 90, 92, Super 92, 300, 410, 510 (1954 & up) Sickle section, heavy gauge, 3" x 3-3/16" under serrated, chrome finish, uses RIV101 rivet. Regular gauge, 3" x 3-3/16", under serrated, plain finish, uses RIV105 rivet. 3" x 3-3/16" Mowers: AEO-A20, AEO-B20, PEO21, PEOA21 (1942-1954), FEO (1950-1954), MH41, MH60 (1940 & up) 130356M1 669807M1 L1262 683936M1 683937M1 830622M1 Heavy gauge, under serrated, plain finish, uses RIV101. Heavy gauge, under serrated, chrome finish, uses RIV101. Regular gauge, under serrated, plain finish, uses RIV105. 3" x 3-1/4" Mower Conditioners: 725, 925 Heavy gauge, top serrated, plain finish, uses RIV101. Heavy gauge, under serrated, plain finish, uses RIV101. Section Rivets and Rivet Assortments No. 5-1/2" x 9/16" oval head rivet (1 lb) 141197 668010M1 Heavy gauge, 3" x 3-3/16", smooth edge, plain finish, uses RIV101 rivet. Heavy gauge, under serrated, plain finish, uses RIV101. CR85 Rivets, #5-1/2 x 5/8" countersunk head rivet (1 lb). 1501221M1 141113CR Regular gauge, under serrated, plain finish, uses RIV105. Regular gauge, 3" x 3-3/16" under serrated, chrome finish, uses RIV105 rivet. RIV66 Packaged assortment of 66 rivets. 1/2" & 7/16" lengths, #5-1/2 oval head section rivets. 261431M1 3" x 3-1/4" Combine: 35, 60, 72, 80, 90, 92 Super 92, 300, 410, 510 (1954 & up) Regular gauge, top serrated, chrome finish, uses RIV105. Replaces 160255M2. RIV66H Same as above, except rivets are 9/16" & 15/16" lengths. For heavy sections. 146503M2 Heavy gauge, top serrated, chrome finish, uses RIV101. Replaces 1261431M1H and 160255M2H. RIV77 Packaged assortment of 77 rivets, 4 lengths, #5-1/2 oval head, for knife head & sections. MF-7-167

7 FORAGE AND HARVESTING Sikl-Fix Rivet Vise Sicklehead Parts SF11 KE114A17 KE114A24 KE114A25 KE114A26 KE114A27 KE114A28 Heavier strong frame! Combination rivet-punch & rivet set vise. Removes & replaces sections on all mowers & other knives without removal or teardown of knife or sickle bar. Now has a frame made of higher tensile strength ductile iron. Knockout screw has been lengthened to add frame strength when riveting. Painted red. Sikl-Fix vise. Vise frame Riveting screw, 3/4" THD Riveting screw cup Riveting screw spring Knockout punch Knockout screw 581387M1 667015M1 195321M1 195196M1 667014M1 667013M1 Dyna-Balance Mowers: 30, 31, 41, 51, 71, 135 Head only, replaces 667011M1. (A) Connector only, for sickle head. (B) Seal for sickle head connector bearing, 2 required. Also used in counterweight except on 41. (C) Needle bearing, for sickle head connector. Replaces 834027M1. (D) Spacer, for sickle head connector bearing. (E) Bolt, has special long shoulder for sickle head connector. (F) Guard & Plow Bolts Tisco supplies coarse thread 7/16"-14 plated bolts, does not include nuts. KE115A28 Knockout screw body, female, 3/4" THD KE116A28 Knockout screw punch holder, 1/2" x 20 THD KE114A1812 Knockout screw punch holder KBSMFC1 Sickle Head Bearing Kit Kit, needle bearing 833083M1 plus 2 seals 831225M1 to repair sickle head on combines: SP300, SP410, SP510. 3534161 3534181 33798S36 Bolt, guard & plow. 7/16"-14 x 1-1/2", No. 3 head, use with 668016M91 and 668017M91. Bolt, guard & plow. 7/16"-14 x 1-3/4", No. 3 head, use with 1501104M1, 1501105M1. Nut, 5/16"-24 x 1/2". Ledger Plates 34670S36 3534271 Nut, 7/16"-14 x 11/16". Nut, 5/8"-18 x 1-1/16" for 181777M1-WNL pin. 34808S36 Lock washer, 7/16". 34811S36 Lock washer, 5/8" for 181777M1-WNL pin. 1502616M1 Use with guards 1501104M1, 1501105M1, 667003M91, 667816M91, 667817M91, 667818M91. Mowers: Ferguson AEO-A20, AEO-B20, PEO-21 & MH 41 & 60, (1942 & up). MF-7-168

7 FORAGE AND HARVESTING Replacement parts to fit DM700 Guards 7/16" bars. Massey Ferguson (LA67 & L215). 699020M1 Stub guard. Windrowers: 725, 925, 885. FD800 1501104M1 679837M91 228392M2 For 1/2" bars. Allis Chalmers, Case, Detroit (N12 & 15294), Ferguson, Ford, Massey Ferguson, Oliver, Worthington. Can Replace Massey Ferguson 501104M1. Malleable guard, heavy-duty, center. Replaces 667003M91, 667817M91, 668016M1. Mowers: AEO-A20, AEO-B20, PEO-21 & Massey Harris 41 & 60, (1942 & up). Bar size 1/2", guard plate number 1502616M1. Guard, heavy-duty center. Mowers: Regular & Dyna-Balance FEO & Side Mount. Guard plate # 679835M1. Two-prong guard, forged steel, for all combines. Buchanan # BC240A. FLW30 Wearing Plates Universal wear plate. Fits all mowers, combines, and swathers with 3" spacing. Knife Clips 515-116K Low knife clip; can replace Massey Ferguson numbers 143241M1, 206195M1. 1501219M1 1502752M1 Knife clip, high arch type. Mowers: Ferguson AEO-A20, AEO-B20, PEO-21. Knife clip, low arch type. Mowers: PEO-A21, Massey Harris 41, 60. 1053174M1 Two-prong guard, forged steel. Combines: 540, 550, 750, 760, 850, 860 (all with floating cutter bar). Buchanan # BU231. Improve Cutting Action With Sic-L-Clip 1036339M1 Two-prong guard, forged steel. Hay-Tedder: MF81. Buchanan # BU280. 1041468M1 683994M1 BU215H Two-prong guard, forged steel. Windrowers: 35, 655, 675, 775, 875. Buchanan # BU235. Two-prong guard, forged steel. Mower Conditioners: 725, 925. Swathers: 775 (table s/n 2734107410 & up), 885. Buchanan # BU215A. Two-prong guard, double heat treat, forged steel. Mower Conditioners: 725, 925. Swathers: 775 (table s/n 2734107410 & up), 885. Buchanan # BU215BH. Can replace 683994M1. SLC330 SLC331 SLC370 SLC371 SLC400 Use one clip every foot on sickle knife. Saves wear on sections. Steel spring holds sections against ledger plates for improved cutting. 4 models fit most cutter bars. Each model packed 12 per display carton. Standard model for 3/8" bolts. Hi-Clear model for 3/8" bolts. Standard model for 7/16" or 1/2" bolts. Hi-Clear model for 7/16" or 1/2" bolts. Replacement Nylatron wear strip (std. pkg. 25). Mower Pittman Wood 669434M1 Pitman wood, 34" length. Mowers: MF32, MF42, MF52. MF-7-169

7 FORAGE AND HARVESTING 12520-TIM Mower Bearings Cup: all mowers. Blades for Rotary Disc/Drum Mowers 12580-TIM Cone: all mowers. 37302225M1 Disc mower blade, LH. 4.75" (120.65mm) length, 2" (50.80mm) width,.72" (18.3mm) hole diameter, 11 degree. Disc Mowers: MF127. 833411M1 833846M1 Ball bearing, blade drive shaft housing. For riding mowers: MF626, MF832/8. Replaces 204RPN-2. Needle bearing, 1" bore, 1.25" O.D. For mower spindle shaft on MF610 riding mower. Replaces B168. 37302226M1 Disc mower blade, RH. 4.75" (120.65mm) length, 2" (50.80mm) width,.72" (18.3mm) hole diameter, 11 degree. Disc Mowers: MF127. Spring Teeth & Fingers for Rakes, Balers, Windrowers & Combines Mower Belts 583923M1 Double tine, for five bar pick-up. Balers: 124 & 125. 195672M1 Belt, 105" length. For Dyna-Balance models. Mowers: MF30 wide, MF31, MF41, MF51 (early). 665929M1 Double tine tooth. Balers: 9, 10, 12. Kosch All-Steel Grassboard 1053394M1 Used on round balers, Model 1440; 32 teeth used prior to s/n 2874-000-636 & 40 teeth after same s/n. Model 1560: 40 teeth used prior to s/n 2696-003-819 & 60 teeth after same s/n. SGB10 Clean sweep all steel board, custom fit to Massey Ferguson mowers. 1059176M1 Tooth, rubber. Balers: 1440, 1455, 1550, 1565. MF-7-170

7 FORAGE AND HARVESTING Replacement parts to fit Flat Head Socket Drive Baler Bolts Grade A alloy, zinc plated. 1005399M1 Tooth, universal reel C5. For use on combines. 3557361 Bolt, flat head socket drive, 1/2"-13 x 1-1/4". For bale chamber shear blade, all balers. H1611 Tooth, Hume reel. For use on combines. Baler Shear Bolts & Nuts Tisco replacement shear bolts & nuts are designed to exacting OEM specifications. For your convenience, shear bolts are priced each, sold in packages of 10 bolts & nuts. 153221M2 Shear bolts: 5/16"-24 x 3-1/8", hex head, grade 2, zinc plated. Nuts: 5/16"-24, steel, hex nut, zinc plated. 667530M1 Rakes: MH21, 25 (s/n 14550 & up). 1045320M1 Baler Friction Slip Clutch Disc Friction slip clutch disc, used in slip clutch assemblies. Balers: 450, 560, 1440, 1450, 1550, 1560. Skidsteer Loader: 811. 6-1/2" O.D., 2-5/8" I.D. 667656M1 668364M1 Rake tooth for model 20 to s/n 14449. Rake tooth for model 36 rake. 1055707M91 Switch For Twine Tie Activator Switch, electric twine tie activator. Round Balers: 634, 640, 645, 656, 1440, 1455, 1550, 1560, 1565. Baler Wire Guide Bearing 1031118M1 Rake tooth. Wheel Rakes: MF29 (s/n 1233-000-001 & up), MF39 (s/n 1411-0000-001 & up). 10" off-set. 832287M91 Roller bearing, V-groove for wire guide. Balers: 10, 126, 130, 220, 224, 228 (646311). 1-1/8" O.D., 1/4" I.D. 1023216M1 Rake tooth. Wheel Rakes: MF29 (to s/n 53131-001). 12-1/2" off-set. MF-7-171

7 FORAGE AND HARVESTING Bale Counters Bearings For Corn Heads 1075494M91 584240M2 Left hand pull lever. Balers: 3, 9, 10, 36. Left hand push lever. Balers: 124, 126. Spacer 833356M1 For Corn Heads: 24, 34, 44, 44-0, 54C; 33, 43, 63, 63C; 64, 83; 62, 82; 1134, 1144, 1164; 1143, 1153, 1163, 1183. Bearing, spherical ball, snapping roll upper shaft. Replaces RA104RRB. 204220M1 Ball bearing, double shielded, snapping roll gear train bearing. 30mm bore. Replaces 206PP, 6206-2RS. 3531401 Ball bearing, double shielded, snapping roll gear train bearing. 35mm bore. Replaces 207NPP, 6207-2RS. 221118M1 Use this spacer to attach a 1100 series bearing retainer (1075208M91) to a 44 series gear box (263234M1). For corn head snapping roll bearing retainer 4 spacers required per retainer. Attach with longer bolts (not supplied) 5/16" x 1-3/4" course thread. 3532361 833735M1 Bearing, double sealed, snapping roll gear train bearing. Replaces 6209-2RS. Ball bearing. Mfr. ref. #6203-16-2RS, this bearing is used in a variety of locations on combine models 750, 760, 850, 860. Used in sprockets & pulleys. Replaces 6203-16-2RS. Needle Bearing For Combine Corn Heads Flute The new Tisco flute is built to exacting specifications of a special abrasion resistant 3/16" steel, red oxide coated. Matches the most recent OEM part. 834475M1 Needle bearing. Used on combine corn heads with #263169M92 corn head gear set. 264687M2 Flute, for snapping rolls on corn heads, series: 1134, 1144, 1164; 1143, 1153, 1163, 1183. Can also replace flutes 245229M91 & 245230M1 on corn heads series: 24, 34, 55, 44-0, 54, 33, 43, 63, 63C, 62, 82; 64, 83; 222, 322, 422; 321, 421, 621. MF-7-172

7 FORAGE AND HARVESTING Replacement parts to fit Ear Corn Deflectors Dust Seal 262510M2 Deflector, left or right, for outer or inner units. For corn heads (except low-profile): 24, 33, 34, 43, 44, 44-0, 62, 63, 63C, 64 To s/n 1864010364, 82, 83 to s/n 1864001361; for outer units only on: 1134, 1143, 1144, 1153, 1163, 1164, 1183. For low-profile corn heads, outer units only on; 24, 33, 34, 43, 44, 54C, 63, 63C, 64, 83. Gathering Chain For Corn Heads 270163M2 For combine engine air intake. Dust seal, for engine air intake, rotary style (drum shaped screen). Combines: 750 (prior to s/n 1696 13713), 760 (prior to s/n 1746 07663), 850, 860. Flex Tines 241090M91 CL2060H Gathering chain: fits corn heads on most late SP combines. Consists of 2060H chain with 8-C6E corn gatherer link spaced every 8th pitch. For corn head models: 24, 34, 44; 33, 43, 63; 62, 82; 64, 84; 222, 322, 422; 321, 421, ; 621; 1134, 1144, 1164; 1143, 1153, 1163, 1183; 540 sweet corn harvester. Connecting And Offset Links For Corn Head Gathering Chain Used with #241090M91 gathering chain or wherever 2060H gathering chain is used. Connecting link, for 2060H chain. 920-366K Flex tine, for combine reels with teardrop style bats. Length 12". Packed 50 pieces per box. 920-246K Flex tine, for combine reels with wood bats. Length 12". Packed 50 pieces per box. Tine Bar Bearing 581318M91 MF Tine Bar Bearing. Rakes: 25, 37, 585, 588. 1-7/8" OD 2-1/8" overall length 1-1/2" thread length 3/4" thread HL2060H Offset link, for 2060H chain. MF-7-173

7 FORAGE AND HARVESTING 837030M93 1041155M1 272130M2 Straw Chopper Knife Kit and Tooth Kits For Hesston manufactured straw choppers designed for various MF combines. Each kit consists of three knives, three bushings, & three bolts. The quantity of knives used per combine ranges from 42 to 54 depending on combine width. Knife set, for straw chopper. Combines: 300 (s/n 116711450 & up), 510 (s/n 120114509 & up), 540, 550, 750, 751, 760, 850, 851, 852, 860. Tooth kit, for Hesston manufactured straw choppers. Contains one tooth, bolt, nut, & lock washer. Combines: 300 (s/n 116711450 & up), 510 (s/n 120114509 & up), 540, 550, 750, 751, 760, 850, 851, 860. Use with Tisco straw chopper kit 837030M93. Auger Finger Holders Auger finger holder, heavy cast, for 9/16" dia. finger. Crankshaft journal bore 1-1/8" approx. Combines: 300, 510 (with 1859 series table), 550 (with 1859 series table), 750, 751, 760, 850, 851, 860. Grain Header: 9000. Auger Fingers & Guides 238797M2 Auger finger for 9/16" ball, 8-1/2" long. Combines: SP300 (with quick attach tables, s/n 1486-08320 & up), SP410, SP510. FH8DMH FH8-25DMH 836998M91 836998-25 293033M2 293054M2 293179M1 Poly finger guide kit, with bolts. Improved replacement for all models using 235279M1 1/2" diameter fingers. Package of 25 of FH8DMH poly finger guides. For 1/2" diameter fingers (bulk pack). Kit, formed poly finger guides (2) with special bolts (4). Improved replacement for models using 238797M2, 9/16" diameter fingers. Replaces CFHKMF916. Package of 25 836998M91 poly finger guides, with bolts. For 9/16" diameter fingers (bulk pack). Combine Rubber Paddle Blades Made from multi-plied conveyor belting. Easier to install - the blades lay flat. Rubber paddle blade. Combines: 760 & 860. Eight used on grain machines. Not for drive shaft at top. Replaces 273003M2. Rubber paddle blade. Combines: 750, 751PT, 850, 851PT, 852PT. Eight used on grain machines. Not for drive shaft at top. Replaces 258133M2. Rubber paddle blade. Combines: 750, 751PT, 850, 851PT, 852PT. Two used per machine on paddle drive shaft. Replaces 258148M2. MF-7-174

7 FORAGE AND HARVESTING Replacement parts to fit Idler Sprockets Combine Slip Clutch & Bushing 263282M1 833491M1 844076M1 833492M1 833494M1 Idler sprocket, 8 tooth, CA550 & 2060 chain, 1/2" bore. Most corn heads. Idler sprocket, 17 teeth, 5/8" bore. Used on auger drive idler. Swather: 775, 785. Idler sprocket, for corn head gathering chain. Has 8 teeth, 5/8" dia. bore. Use with CA550 & 2060 chain, also with gathering chain 241090M91. Corn Heads: 1134, 1144, 1164, 1143, 1153, 1163, 1183. Idler sprocket, 18 teeth, 5/8" bore. For drive mounting plate on forage box: 114, 116. Idler sprocket, 15 teeth, 1/2" bore. Primarily used on idler tension arm or lower drive roller. Round Balers: 450, 640, 1440, 1450, 1455, 1550, 1560, 1565. Combine Wooden Idler Blocks RASC-1 228989M1 228990M1 240465M1 263648M91 Slip clutch kit, for straw walker & return elevator drives. Combines: MF410, MF510, MF750, MF760. Slip clutch, outer Slip clutch, inner Bushing, 7/8" I.D., 1 O.D. (2 used) Combine Drive Chain Assemblies Pitch indicates distance center to center of roller pins. Double strand #60, 3/4" pitch roller chain, made up of 162 pitches. Corn Heads: 24, 33, 43, 63C, 64. 243346M1 Wooden idler block, used on the cylinder drive, grain elevator, & other applications. Combines: 205, 300, 410, 510 (s/n 1201003653 to 1201026828), 540 & 550. 2-9/16" O.D., 7/16" I.D., 1-1/8" wide. Wooden Boxings (Bearing) Part number is for one pair of wooden boxings (two bearing halves) with bolts, nuts, & shims. 836784M92 Wooden boxings (one pair) with bolts, nuts, & shims. For straw walkers. Combines: 750, 751, 850, 851. 836751M92 Wooden boxings (one pair) with bolts, nuts, & shims. For straw walkers. Combines: 760, 860. MF-7-175

7 FORAGE AND HARVESTING Combine Belts The information below is drawn from OEM parts reference and vendor belt interchange data. Serial numbers and other information relating to specific machines are shown in parentheses. Reference is made to applications for machines identified as S/N (early production or for prior serial number machines) or S/N (late production or for late serial number machines). 227457M1 227984M1 227986M2 228813M3 259047M91 265522M91 273757M91 274015M91 274339M91 281560M91 529964M1 832866M2-D 832906M1-D 833854M2 833855M1 833857M4-D 833858M4-D 833860M1 833862M3 833863M1 833865M1-D 833867M1 833868M2-D 833871M1-D 833872M1-D 833873M1 833874M1-D 833962M1 834110M1-D 834140M1 834174M1-D 834190M1 834332M1 842110M1 842413M2 843198M1 843747M1-D 844163M1 Application Reel countershaft (s/n 410 & up); (cleaning fan 510 and 550) Reel (s/n 410 & up), grain auger (510 and 550) Return auger and walker Tank unloader Pair, radiator fan (Diesel) pair, radiator fan Pair, shaker shoe Pair, shaker countershaft Pair, radiator fan, gas Fan and shaker shoe. 750, 760 A/C (Frigidaire) Straw chopper, #2, Straw chopper, #3. 750 (to s/n 1696016539), 760 (to s/n 1746009413) Return elevator Straw walker Traction drive, 4 speed, upper. 750 (to s/n 1696013713) Traction drive, 4 speed, upper & lower. 750 (to s/n 1696013713), 850 upper Straw walker Unloader drive Cleaning fan Main drive 760 (air intake), 860 (rotary screen) Cylinder drive Straw chopper, #1. 750 Straw chopper, #3. 750 Grain tank unload, auger Main drive Wobble drive Traction drive, upper Reel drive Traction drive, lower, grain Knife drive (refer to OEM guide for s/n breaks) Slinger (aux. cylinder) Straw spreader Hydraulic pump (refer to OEM guide for s/n breaks) Wobble drive Straw chopper, #2. 750 (prior to s/n 1696016539), 760 (prior to s/n 1746009413) Alternator, V8 205 300 410 510 540 550 750 760 850 860 MF-7-176

8 IMPLEMENTS AND BEARINGS Replacement parts to fit Self-Aligning Spherical Ball Bearings With Collars Wide Inner ring bearings designed for extremely dirty & wet conditions - available in non-relubricating & re-lube types. Both extended inner ring (RA & GRA series) and wide inner ring (1100 & G1100 series). Suffixes PPB & RRB indicate double seals & spherical outside diameters for us in housings with same spherical inside surfaces to allow unrestricted self-alignment. Bearings listed will be individually packaged complete with eccentric locking collars and labeled according to numbers ordered. Part numbers are used only for purposes of identification. Replaces 22690 3531141 3531341 3531611 3750681 831929M1 832122M1 833351M1 833356M1 834066M1 834197M1 834199M1 842736M1 TWAHB8MF 421239M1 446612M1 420430M1 REF. # (A) (A) (A) (A) (B) (A) (A) (A) (A) (B) (A) (A) (A) BORE SIZE (IN) 1-1/4" 3/4" 1-1/16" 1-3/16" 1-3/8" 1-1/8" 1-1/2" 1-3/8" 1-1/4" 1-1/2" 7/8" 1" 1" Cultivator Gauge Wheels & Related Items Cultivator gauge wheel assembly, for single arm gauge wheels. Contains 2 wheel halves, a bearing, & a 4" x 12" tire. Wheel half, cultivator. Rim diameter 8-5/8", rim width 2". Special sealed ball bearing for cultivator gauge wheel, 2.890" overall length, bearing 1.531" L, shaft 1.198" L x.6267" O.D. Cultivator tire, 4" x 12". OUTER DIA. (IN) 2.4409" 1.8504" 2.4409" 2.4409" 2.8346" 2.4409" 3.1496" 2.8346" 2.8346" 3.1496" 2.0472" 2.0472" 2.0472" 686187M1 833045M1 OUTER DIA. (MM) 62mm 47mm 62mm 62mm 72mm 62mm 80mm 72mm 72mm 80mm 52mm 52mm 52mm Cultivator Washer MFR. REF. NO. RA103RRB2 RA012RRB RA101RRB RA103RRB 1106KRRB RA102RRB RA108RRB RA106RRB RA104RRB 1108KRRB RA014RRB RA100RRB RA100RRB Special cultivator washer, sweep to arm. Special Ball Bearing Special ball bearing with hex bore used on MF54 flail forage harvester & on 260 heavy-duty forage harvester. MF-8-177

8 IMPLEMENTS AND BEARINGS Combine Bearings These bearings are used in several combine models with the majority found in combines: 750, 760, 850 & 860. We did not attempt to list specific usage because these bearings have many applications. However, we do list a manufacturer reference number opposite the Massey part number & an example location where each bearing could be used. 831822M1 831861M1 3531441 832087M1 Ball bearing. Mfg. number 1726207-2RS. Used in a variety of locations on combines listed above, including table and reel drive. Ball bearing. Mfg. number 1726307-2RS. Used in a variety of locations on combines listed above, including auger. Ball bearing, double shielded, 25mm bore, replaces 305NPP, 6305-2RS. Ball bearing. Mfg. number 1726208-2RS. Used in a variety of locations on combines listed above, including elevator to table drive. 3531521 Ball bearing, spherical O.D., 20mm bore, replaces 204PPB. 832198M1 Ball bearing. Mfg. number 6201-2RS. Used in a variety of locations on combines listed above, including table and reel drive. 833735M1 3529761 22258 3530671 828123M2 175047M1 204220M1 3532461 831134M1 3503961 3531401 Ball bearing. Mfr. ref. #6203-16-2RS, this bearing is used in a variety of locations on combine models 750, 760, 850, 860. Used in sprockets & pulleys. Ball bearing. Mfg ref. number 6208-2RS. Used in a variety of locations on combines referenced above. Ball bearing, double shielded, I.D. 0.9843" (25mm), O.D. 2.0472", W. 0.5906". Replaces 205PP, 6205-2RS. Ball bearing. Mfg. number 6205-2RSQ. Used in a variety of locations on combines listed above, including hydraulic pump drive. Ball bearing, double shielded, 17mm bore. Replaces 203PP, 6203-2RS. Ball bearing, double shielded, 15mm bore. Replaces 202PP, 6202-2RS. Ball bearing, double shielded, snapping roll gear train bearing. 30mm bore, replaces 206PP, 6206-2RS. Ball bearing. Mfg. number 6306-2RS. Used in a variety of locations on combines listed above, including grain elevator drive. Ball bearing. Mfg. number 1726209-2RS. Used in a variety of locations on combines listed above, including auger. Ball bearing, double shielded, 20mm bore, replaces 204PP-IMP, 6204-2RS. Ball bearing, double shielded, snapping roll gear train bearing. 35mm bore, replaces 207NPP, 6207-2RS. 3549191 3549201 832686M1 833059M1 3549211 831087M1 833647M1 831112M1 833741M1 831224M1 833757M1 831622M1 831728M1 Ball bearing, double shielded, 50mm bore, replaces 210NPP, 6210-RS. Ball bearing, double shielded, 35mm bore, replaces 307NPP, 6307-2RS. Ball bearing. Mfg. number 6204-RSJ. Used in a variety of locations on combines listed above, including radiator fan shaft. Ball bearing. Mfg. number 6208-2RS. Used in a variety of locations on combines listed above, including electric variable speed reel drive. Ball bearing, double shielded, 40mm bore, replaces 308NPP, 6308-2RS. Ball bearing, spherical O.D., 30mm bore, replaces 206NPPB. Ball bearing. Mfg. number 6308. Used in a variety of locations on combines listed above, including cylinder drive. Ball bearing, spherical O.D. 25mm bore, replaces 205PPB. Ball bearing. Mfg. number 1726210-2RS. Used in a variety of locations on combines listed above, including elevator top shaft drive. Needle bearing, replaces B2016. Ball bearing. Mfg. number 1726305-2RS. Used in a variety of locations on combines listed above, including table and reel drive. LM67048L cone with LM67000 seal assembly. Used with cone 67010 on combines 35PT & SP, cylinder drive shaft in pulley hub. Corn heads 20 & 22, main auger drive shaft & snapping rolls. Bearing cone, 1.625" I.D.,.78" width. MF-8-178

8 IMPLEMENTS AND BEARINGS Replacement parts to fit 834869M1 831729M1 Ball bearing. Mfg. number 6309-2RS. Used in a variety of locations on combines listed above, including cylinder drive. Bearing cup, 2.891" O.D.,.58" width. Popular Disc Bearings @Body Copy:Spherical O.D. ball bearings for various disc applications. Manufacture Reference Number 842047M1 Ball bearing. Mfg. number 6018Z. Used in a variety of locations on combines listed above, including cylinder drive. 832009M1 Ball bearing, spherical O.D., 15mm bore, replaces 203NPPB. 842079M1 Ball bearing. Mfg. number 1726309-2RS. Used in a variety of locations on combines listed above, including grain pan and shaker shaft. 832189M1 832190M1 842434M1 842503M1 832629M1 842504M1 Bearing cone, 1.000" I.D.,.56" width. Bearing cup, 1.98" O.D.,.42" width. Ball bearing. Mfg. number 1726210-2RS. Used in a variety of locations on combines listed above, including rasp bar cylinder. Ball bearing. Mfg. number 6209-2RS. Used in a variety of locations on combines listed above, including grain elevator drive. Ball bearing, double shielded, special size, 35mm bore, replaces 207KRR3. Ball bearing. Mfg. number 210ZJ. Used in a variety of locations on combines listed above, including grain elevator drive. 6210Z. Replaces 449432M1 832540M1 832634M3 834367M1 842303M1 1066086M1 22520-PR FAFNIR GW211PPB3 W211PPB3 W208PPB23 W208PPB6 W209PPB5 GW209PPB5 B.C.A. DS211TTR3 DS211TT3 DS208TT2A DS208TT6 DS209TT5 DS209TTR5 NEW DEP. RAS4511BE AS4511BE AS4509B AS4509A RAS4509A Flangette for Self-Aligning Bearings Sold in pairs only. Flangettes, round, non-relube, with 4 holes; for 3.1496" (80mm) O.D. bearings (F4-80) 832651M1 842660M1 832337M1 832339M1 842736M1 842874M1 833083M1 833846M1 834135M1 Ball bearing, double shielded, replaces 203KRR2. Ball bearing. Mfg. number 1726305-2RS. Used in a variety of locations on combines listed above, including radiator fan drive. Bearing race (IRA-8), 300 combines various applications. Roller assembly (B1212), 300 combines various applications. Ball bearing. Mfg. number RA100RRB. Used in a variety of locations on combines listed above, including grain elevator drive. Ball bearing. Mfg. number 1736208-109. Used in a variety of locations on combines listed above, including elevator to table drive. Needle bearing, knife head on combines: SP300, SP410, SP510. Needle bearing, 1" bore, 1.25" O.D. For auger drive shaft on combines: 410, 510. Replaces B168. Bearing cone, 1.5" I.D.,.72" width. 22286 22691-PR 541388M2 FTR352 3-bolt round steel flangette used to retain power transmission bearing. O.D. 2.0472" (52mm) used with 7/8", 13/16", 15/16" & 1" bore bearings. For pull-type machines. Combines: 35, 60, 72, 405, 751 & 851. For self-propelled machines Combines: 35, 60, 72, 80, 82, 90, 92, 92 Super, 300, 5. (F3-52) Flangettes, round, non-relube, with 3 holes, for 2.4409" (62mm) O.D. bearings (F3-62) Flangettes, round, non-relube, with 3 holes, for 2.8346" (72mm) O.D. bearings (F3-72) Flangettes, triangular, non-relube, for 2.0472" (52mm) O.D. bearings. Replaces 833474M1. 834136M1 Bearing cup, 2.5625" O.D.,.55" width. MF-8-179

8 IMPLEMENTS AND BEARINGS Wheel Bearing Kit for Harrows and Plows Tapered Bearing Cups and Cones MF-WBK520 Wheel bearing kit, services one wheel. Disc Harrows: 520, 620, 720, 820. Plows: 43, 345 (with 1-3/4" O.D.) gauge wheel, 370 (reversible) gauge wheel. Chisel Plows: 129 (main wheels & crank type gauge wheel), 139. 833094M1 833095M1 Tapered cup (LM603011). Tapered cone (LM603049). 449426M1 Seal 1037463M1 Wear sleeve LM29710-TIM Bearing cup LM29749-TIM Bearing cone LM67010-TIM Bearing cup LM67048-TIM Bearing cone MF-8-180

8 IMPLEMENTS AND BEARINGS Replacement parts to fit 6000 Series Bearings (Flat Edge) Replaces 195494M1 Reference Number 6010-Z A Bore Dia. (A) 1.9685" 6200 Series Bearings (Flat Edge) B O.D. (B) 3.1496" C Width (C) 0.6299" Bearing Sides 1 shield Replaces 832198M1 175047M1 833735M1 828123M2 832953M3 832960M3 832686M1 3530671 204220M1 3531401 3529761 195505M1 3532361 842503M1 842504M1 3549191 195493M1 195507M1 Reference Number 6201-2RS 6202-2RS 6203-2RS 16MM 6203-2RS 6203-ZZ 6203ZZ 6204-2RS 6205-2RS 6206-2RS 6207-2RS 6208-2RS 6208Z 6209-2RS 6209-2RS 6210Z 6210-2RS 6210ZZ 6211Z A Bore Dia. (A) 0.4724" 0.5906" 0.6299" 0.6693" 0.6693" 0.6693" 0.7874" 0.9843" 1.1811" 1.378" 1.5748" 1.5748" 1.7717" 1.7717" 1.9685" 1.9685" 1.9685" 2.1654" B O.D. (B) 1.2598" 1.378" 1.5748" 1.5748" 1.5748" 1.5748" 1.8504" 2.0472" 2.4409" 2.8346" 3.1496" 3.1496" 3.3465" 3.3465" 3.5433" 3.5433" 3.5433" 3.937" C Width (C) 0.3937" 0.4331" 0.4724" 0.4724" 0.4724" 0.4724" 0.5512" 0.5906" 0.6299" 0.6693" 0.7087" 0.7087" 0.748" 0.748" 0.7874" 0.7874" 0.7874" 0.8268" Bearing Sides 2 contact seals 2 contact seals 2 contact seals 2 contact seals 2 shields 2 shields 2 contact seals 2 contact seals 2 contact seals 2 contact seals 2 contact seals 1 shield 2 contact seals 2 contact seals 1 shield 2 contact seals 2 shields 1 shield MF-8-181

8 IMPLEMENTS AND BEARINGS 6300 Series Bearings (Flat Edge) Replaces 828123M2 3531441 3532461 3549201 833647M1 3549211 834869M1 Reference Number 6203-2RS 6305-2RS 6306-2RS 6307-2RS 6308 6308-2RS 6309-2RS A Bore Dia. (A) 0.6693" 0.9843" 1.1811" 1.378" 1.5748" 1.5748" 1.7717" B O.D. (B) 1.5748" 2.4409" 2.8346" 3.1496" 3.5433" 3.5433" 3.937" C Width (C) 0.4724" 0.6693" 0.748" 0.8268" 0.9055" 0.9055" 0.9843" Bearing Sides 2 contact seals 2 contact seals 2 contact seals 2 contact seals Open 2 contact seals 2 contact seals MF-8-182

9 MISCELLANEOUS Replacement parts to fit 533713M91 269925M91R 269925M91 CL621029C0 CL625855C0 72504984 71379601 Compressors Air conditioning compressor. Reman A6, 12 Volt 2 o'clock, New 5.58" clutch, Superheat compressor. Superheat switch not included. Tractors: MF1080, MF1085, MF1100, MF1105, MF1130, MF1135, MF1150, MF1155, MF1500, MF1505, MF1800, MF1805, MF2640, MF2675, MF2705, MF2745, MF2775, MF2805, MF3505, MF3525, MF3545, MF4800, MF4840, MF4880, MF4900. Combine: 540, 550, 750, 760, 850, 860. Air conditioning compressor, Reman York - LH suction, Rotolock. Clutch not included. Combine: 510, 8590, 8680, 9720. Air conditioning compressor, New York LH suction, Rotolock. Clutch not included. Combine: 510, 8590, 8680, 9720. Air conditioning compressor, New York RH suction, Rotolock. Clutch not included. Combine: 510, 8450, 8460. Air conditioning compressor, New York RH suction, Tube-O. Clutch not included. Combine: 8460. Air conditioning compressor, New Original Sanden - ear mount - SD7H15, 5 1/4" 2-groove clutch, vertical tube o-ring. Tractors: MF9240. Air conditioning compressor, New Original Sanden - ear mount - SD7H15, 5-1/4" 2-groove clutch, horizontal tube - o-ring. Combine: 8680, 8780, 9790. 3712528M2R 533713M91S 1904014M92 Air conditioning compressor, New Aftermarket original Sanden- ear mount - SD7H15, 5-1/2" 2-groove clutch. Tractors: MF366, MF3545, MF3630, MF3645, MF3650, MF3655, MF3660, MF4233, MF4240, MF4243, MF4245, MF4253, MF4255, MF4260, MF4263, MF4265, MF4270, MF5460, MF5470, MF5480, MF6140, MF6150, MF6170, MF6180, MF6190, MF6235, MF6245, MF6255, MF6270, MF6280, MF6290, MF6445, MF6455, MF6460, MF6465, MF6470, MF6475, MF6480, MF6485, MF6490, MF6495, MF6497, MF6499, MF7465, MF7475, MF7480, MF7485, MF7490, MF7495, MF8120, MF8140, MF8150, MF8160, MF8210, MF8220, MF8240, MF8245, MF8250, MF8260, MF8270, MF8280, MF8450, MF8460, MF8470, MF8480. Air conditioning compressor, New compressor. Kit, A6 to Seltec conversion kit. Mounts to original compressor. Kit allows for the use of the original hoses and adapts to original A6 mounting brackets. Tractors: MF1080, MF1085, MF1100, MF1105, MF1130, MF1135, MF1150, MF1155, MF1805, MF2640, MF2675, MF2705, MF2745, MF2775, MF2805, MF3505, MF3525, MF3545, MF4800, MF4840, MF4880, MF4900. Combine: 850. Air conditioning compressor, replacement for Frigidaire A-6 compressor. Includes 5.58" dia. clutch & dust cover, high pressure relief valve. With 12V coil at 10 o-clock, SAE thread. Less superheat switch (comes plugged with non-functional heat switch, new oring & snap ring). MF-9-183

9 MISCELLANEOUS Blower Switch Pressure Switches 271105M1 3902701M91 1072139M91 3310669M91 Blower Switch - 3-speed blower switch with knob. Tractors: MF285, MF1085, MF1105, MF1135, MF1155, MF1500, MF1505, MF1800, MF1805, MF3050, MF4800, MF4840, MF4880, MF4900, MF9240. Combine: 750, 760. Thermostatic Switch Thermostatic switch - rotary adjustable, 48" capillary tube, with knob. Tractors: MF150, MF1080, MF1085, MF1100, MF1105, MF1130, MF1135, MF1155, MF1800, MF1805, MF2640, MF2675, MF2705, MF2745, MF2775, MF2805, MF3525, MF3545, MF3505, MF4800, MF4840, MF4880, MF4900, MF6140, MF6150, MF6170, MF6180, MF6190, MF6235, MF6245, MF6255, MF6270, MF6280, MF6290, MF8120, MF8140, MF8150, MF8160, MF8210, MF8220, MF8240, MF8245, MF8250. Thermostatic switch - rotary adjustable, 36" capillary tube. Combine: 8560, 8570, 8590. Thermostatic switch. Rotary adjustable, 36" capillary tube. Tractors: MF699, MF670, MF690, MF698, MF660, MF680, MF3050, MF3060, MF3065, MF3070, MF3075, MF3080, MF3090, MF3095, MF3120, MF3120T, MF3125, MF3125 French, MF3140, MF3630, MF3645, MF3650, MF3655, MF3660, MF3670, MF3680, MF3690, MF6140, MF6150, MF6170, MF6180, MF6190, MF6235, MF6245, MF6255, MF6270, MF6280, MF6290, MF8120, MF8140, MF8150, MF8160, MF8210, MF8220, MF8240, MF8245, MF8250, MF8260, MF8270, MF8280. 3712526M1 837255M91 72506492 72162165 250958M1 Switch HI-LO pressure, Binary switch - 7/16"-2 female flare thread, normally open. Tractors: MF3645, MF3655, MF3660, MF3670, MF3680, MF3690, MF4225, MF4233, MF4235, MF4240, MF4243, MF4245, MF4253, MF4255, MF4260, MF4263, MF4265, MF4270, MF6140, MF6150, MF6170, MF6180, MF6190, MF6235, MF6245, MF6255, MF6270, MF6280, MF6290, MF8120, MF8140, MF8150, MF8160, MF8210, MF8220, MF8240, MF8245, MF8250, MF8260, MF8270, MF8280. Compressor mounted switch - A6 superheat switch. Tractors: MF1080, MF1085, MF1100, MF1105, MF1130, MF1135, MF1150, MF1155, MF1500, MF1505, MF1800, MF1805, MF2640, MF2675, MF2705, MF2745, MF2775, MF2805, MF3525, MF3545, MF3505, MF4800, MF4840, MF4880, MF4900. Combine: 540, 550, 750, 760, 850, 860. High pressure switch - normally closed. Closes 225 psi, opens 375 psi. Tractors: MF9240. Low pressure switch - open - drier mount, normally open. Opens 30 psi, closes 30 psi. Combine: 8560, 8570, 8590, 9720. High pressure switch - closed - thermo-disc switch. Opens at 200 F. Combine: 510, 760. MF-9-184

9 MISCELLANEOUS Replacement parts to fit MF5304015 837492M91 286127M1 Pressure switch kit, compressor mounted. A6 compressor R134 binary pressure switch kit. Tractors: MF1080, MF1085, MF1100, MF1105, MF1130, MF1135, MF1150, MF1155, MF1500, MF1505, MF1800, MF1805, MF2640, MF2675, MF2705, MF2745, MF2775, MF2805, MF4800, MF4840, MF4880, MF4900. Combine: 540, 550, 750, 760, 850, 860. High-Pressure Switch. Normally closed, compressor mount. Replaces red, tan, and dark orange, includes pigtail. Opens 430 psi, closes 200 psi. Tractors: MF4800, MF4840, MF4880, MF4900, MF2640, MF2675, MF2705, MF2745, MF2775, MF2805. Combines: 550, 850, 855, 860, 865, 8570, 8780. Limiter Fuse Thermal limiter fuse, compressor mounted switch. Tractors: MF1080, MF1085, MF1100, MF1105, MF1130, MF1135, MF1150, MF1155, MF1500, MF1505, MF1800, MF1805, MF2640, MF2675, MF2705, MF2745, MF2775, MF2805, MF3525, MF3545, MF3505, MF4800, MF4840, MF4880, MF4900. Combine: 550, 750, 760, 850, 855, 860, 865. Receiver Driers 3039149M91 2-1/2" diameter receiver drier - 2-1/2" x 8" male o-ring, R12 and R134a compatible. Tractors: MF2675, MF2705, MF2745, MF2775, MF2805. 250929M1 3763351M1 3383321M2 3712495M1 3" diameter receiver drier - 3" x 6" male flare, R12 and R134a compatible. Tractors: MF285, MF1080, MF1085, MF1100, MF1105, MF1130, MF1135, MF1150, MF1155, MF1500, MF1505, MF1800, MF1805, MF4800, MF4840, MF4880, MF4900. Combine: 750, 760. 3" diameter receiver drier - 3" x 9-1/2" male flare, male switch port. Tractors: MF670, MF690, MF698. 3" diameter receiver drier - 3" x 7" male o-ring, male switch port, R12 and R134a compatible. Tractors: MF365, MF375, MF383, MF390, MF390T, MF393, MF396, MF398, MF399, MF3050, MF3060, MF3065, MF3070, MF3075, MF3080, MF3090, MF3095, MF3120, MF3120T, MF3125, MF3125 French, MF3140, MF3505, MF3525, MF3545, MF3630, MF3645, MF3650, MF3655, MF3660, MF3670, MF3680, MF3690. 3" diameter receiver drier - 3" x 9" male o-ring, R12 and R134a compatible. Tractors: MF307, MF3050, MF3065, MF3645, MF3655, MF3660, MF3670, MF3690, MF4225, MF4233, MF4235, MF4240, MF4243, MF4245, MF4253, MF4255, MF4260, MF4263, MF4265, MF4270, MF6140, MF6150, MF6170, MF6180, MF6190, MF6235, MF6245, MF6255, MF6270, MF6280, MF6290, MF8120, MF8140, MF8150, MF8160, MF8210, MF8220, MF8240, MF8245, MF8250, MF8260, MF8270, MF8280. MF-9-185

9 MISCELLANEOUS 71369761 529876M91 30-3178706 1072136M91 3380223M1 104867W1 3" diameter receiver dries - 3" x 1-1/2" male o-ring, R12 and R134a compatible. Combine: 8680, 8780, 9790. Expansion Valves Expansion valve, bulb type - flare - internally equalized with 12" capillary tube, R12 and R134a compatible. Tractors: MF1085, MF1105, MF1135, MF1155, MF1500, MF1505, MF1800, MF1805, MF4800, MF4840, MF4880, MF4900. Combine: 510, 750, 760. Expansion valve, bulb type - flare - externally equalized with 12" tube length, R12 and R134a compatible. Combine: 8570. Expansion valve, bulb type - flare - externally equalized with 19" capillary tube, R12 and R134a compatible. Combine: 8560, 8590, 9720. Expansion valve, bulb type - o-ring - externally equalized with 14" capillary tube, R12 and R134a compatible. Tractors: MF670, MF690, MF698, MF699, MF2640, MF2675, MF2705, MF2745, MF2775, MF2805, MF3505, MF3525, MF3545. Expansion valve, block valves. R12 and R134a compatible, 1/4" mounting holes. Tractors: MF285, MF3050, MF3060, MF3065, MF3070, MF3075, MF3080, MF3090, MF3095, MF3120, MF3120T, MF3125, MF3125 French, MF3140, MF3630, MF3645, MF3650, MF3655, MF3660, MF3670, MF3680, MF3690, MF6235, MF6245, MF6255, MF6260, MF6265, MF6270, MF6280, MF6290, MF9240. Combine: 850, 855, 860, 865, 8570, 8680. 3901517M1 3902334M91 3038920M91 Expansion valve, block valves. R12 and R134a compatible, 1/4" mounting holes. Tractors: MF4225, MF4233, MF4235, MF4240, MF4243, MF4245, MF4253, MF4255, MF4260, MF4263, MF4265, MF4270, MF6140, MF6150, MF6170, MF6180, MF6190, MF6235, MF6245, MF6255, MF6260, MF6265, MF6270, MF6280, MF6290, MF8120, MF8140, MF8150, MF8160, MF8210, MF8220, MF8240, MF8245, MF8250. Block valves - expansion valve, R12 and R134a compatible. Tractors: MF306, MF3050, MF3645, MF3655, MF3660, MF3670, MF3690, MF6140, MF6150, MF6170, MF6180, MF6190, MF6235, MF6245, MF6255, MF6270, MF6280, MF6290, MF8120, MF8140, MF8150, MF8160, MF8210, MF8220, MF8240, MF8245, MF8250, MF8260, MF8270, MF8280. Expansion valve. O-ring, internally-equalized with 12" capillary tube, R12 and R134A compatible. Tractors: MF374S, MF375, MF383, MF384S, MF390, MF390T, MF393, MF394S, MF396, MF398, MF399, MF2675, MF2705, MF2745, MF2775, MF2805. Combines: 550, 750, 760, 850, 860. MF-9-186

9 MISCELLANEOUS Replacement parts to fit Blower Motors 1071957M91 Blower motor - double shaft - 12 volt single speed 2 wire motor with 3/8" shafts. Combine: 8560, 8570, 8590. 1048515M91 1894742M91 Blower motor - double shaft - 12 volt 3 speed 4 wire motor with 3/8" shafts, heavy duty ball bearing motor. Tractors: MF285, MF1085, MF1105, MF1135, MF1155, MF1500, MF1505, MF1800, MF1805, MF4800, MF4840, MF4880, MF4900, MF9240. Combine: 750, 760, 850, 855, 860, 865. Blower Motor, replacement motor with 5/16" shafts. 12 volt single speed, 2 wire motor. Original replacement motor. Tractors: MF2640, MF2675, MF2705, MF2745, MF2775, MF2805, MF3505, MF3525, MF3545. Blower Assemblies BU10211R MF311541 Bumpers and Mounting Arms Complete, sturdy angle iron grill, same for all models. Mounting arms sold separately for optional applications. Bumper & grill assembly, mounting arms NOT included. Assembly comes painted. Heavy-duty front bumper. Four bars for extra protection. Bumper comes primed. (311541HD) 3310831M91 Blower assemblies - blower motor with wheels. 5/16" shaft, 14" overall length, 2.880" motor diameter. 2 spade wires. Tractors: MF3065, MF3070, MF3075, MF3080, MF3090, MF3095, MF3120, MF3120T, MF3125, MF3125 France, MF3630, MF3645, MF3650, MF3655, MF3660, MF3670, MF3680, MF3690, MF6140, MF6150, MF6170, MF6180, MF6190, MF6235, MF6245, MF6255, MF6270, MF6280, MF6290, MF8120, MF8140, MF8150, MF8160, MF8210, MF8220, MF8240, MF8245, MF8250, MF8260, MF8270, MF8280. BU10212R BU10220 Mounting arm, right or left. Tractors: TE20, TO20, TO30, MF35 (axle mount). Two required with BU10211R. Arm comes painted. Mounting arm right or left. Tractors: MF135 (axle mount). 2 required with BU10211R. Arm comes painted. BU1027 Bumper kit, for axle mount. Tractors: MF135. Kit contains 1 - BU10211R grill and 2 - BU10220 mounting arms. Kit components come primed. MF-9-187

9 MISCELLANEOUS Emblems 182564M2 Front emblem, includes clips. 6" wing span, 6" nose to tail, 3-5/8" center to center (bolt holes) Painted red. Retaining clip not included. Tractors: MF50, MF65, MF85, MF88, MF97, MF98. Vintage Iron 181628M1 181707MPAR 180661M1 187990M1 183193M1 SNETMF 181709MPAR Front emblem with bracket. 3-3/4" W x 1-1/2" H, 2-1/8" C.C. Includes clips. Ferguson rectangle w/blue background, USA made. Tractors: TO20, TE20, TEA20, TO30. Vintage Iron Side Emblems, Ferguson. Blue background, 1-5/16" H x 9-5/8" W. Includes clips, sold as a pair. Attaches w/3 pegs. Tractors: TO20, TE20, TEA20. Vintage Iron Front emblem. 4-1/2" W x 2-1/2" H, 2" C.C. Includes clips. Ferguson shield w/red background. USA made. Tractors: TO35 (s/n 176341 & up). Vintage Iron Front emblem. Die cast (metal). Painted and chromed. Tractors: MF35. Vintage Iron Side emblem, "Ferguson 35". 1-1/4" x 9-7/8". Includes clips. Sold individually. Red background. Attaches w/3 pegs. 4.1225" between pegs. Tractors: TO35, MF35. Vintage Iron Blank engine serial number tag with 4 rivets. Black anodized aluminum. 3.885" long x 1.885" tall. Customer must stamp number. Tractors: F40, TO35, MF35, MF50, MH50, Early MF135. Industrials: 202, 203, 204, 2135. Vintage Iron Side emblem pair, "Massey Ferguson 30". 1-5/16" x 9-5/8". Sold as a pair. Blue background. Attaches w/3 pegs. Tractors: TO30. Vintage Iron 184792M1 SNETTO 508891M91 194200M92 194236M2 194235M1 Front emblem. 4.5" tall, 6.25" long. Tractors: MF50 (Gas / LP, to s/n 529881), MF65 (Gas / LP / Diesel, to s/n 685393), MF85, MF88, MF95, MF98, Super 95. Vintage Iron Blank engine serial number tag with 4 rivets. Black anodized aluminum. 3.885" long x 1.885" high. Customer must stamp numbers. Tractors: TO20, TE20 (w/continental Z120 engine). Vintage Iron Metal Nose Cone Assembly & Replacement Parts Metal nose cone assembly. Contains new style stamped metal nose cone (primed), screen, bar & emblem. Tractors: MF135, MF150, MF165, MF175, MF180. Industrials: 20, 30, 31, 2135, 3165. Nose cone comes primed. Replaces 512009M91. Nose cone, metal, less screen, bar & emblem. Tractors: MF135, MF150, MF165, MF175, MF180. Industrials: 20, 30, 31, 2135, 3165. Replaces plastic or early style cast metal nose cones. Nose cone comes primed. Screen, black painted steel, for metal or plastic nose cones. Tractors: MF135, MF150, MF165, MF175, MF180. Industrials: 20, 30, 31, 2135, 3165. Plastic center nose cone bar with emblem. Tractors: MF135, MF150, MF165, MF175, MF180. Industrials: 20, 30, 31, 2135, 3165. Vintage Iron MF-9-188

9 MISCELLANEOUS Replacement parts to fit 531061M91 Individual Grill Parts Top grill door. Tractors: MF230, MF235, MF245. Industrial: 20C. 194181M91 Front grill door. Tractors: MF150, MF165, MF175. Industrials: 30, 31, 3165. MGK135 183661M91 Grill kit. Tractors: MF135. Industrials: 20, 2135. Center bar & hinge assembly. Tractors: MF40 (late model), MF50, MF65. 181627M91 186888M91 Grill, front. Tractors: TE20, TO20, TO30. Lower Grill Pan. Tractors: TO35 gas (s/n 204408 & up), MF35 gas & diesel. Vintage Iron 194192M92 Grill shell. Tractors: MF135. Industrials: 20, 2135. 180615M91 Lower grill pan. Tractors: TO35 gas (to s/n 204408). Vintage Iron 532260M92 183662M92 182421M92 531060M91 194182M91 Top grill door. Tractors: MF255, MF265, MF275, MF285. Left grill door, clip-on design for easy access to radiator & air cleaner. Tractors: MF40 (late model), MF50, MF65. Use existing hardware. Right grill door, bolt-on design. Duplicates the OEM part. Tractors: MF40 (late model), MF50, MF65. Use existing hardware. Bottom grill door. Tractors: MF230, MF235, MF245. Industrials: 20C. Front grill door. Tractors: MF135. Industrials: 20, 2135. 191383M91 391347R1 539310M1 Front Grill. Tractors: TO35, MF35. Uses original mounting brackets (not available for purchase). Vintage Iron Front grill screen fastening spring. Secures screen to grill. 4 required, sold individually. Tractors: TE20, TO20, TO30, TO35. Vintage Iron Rubber Hood Trim Rubber hood trim, between grill frame, hood & side panels. 115" long, cut to fit. Tractors: MF230, MF235, MF245, MF255, MF265, MF275, MF285, MF1085, MF1105, MF1135, MF1155. Replaces 532170M1, 535111M1. MGK165 Grill kit. Tractors: MF150, MF165, MF175. Industrials: 30, 31, 3165. 532234M91 Bottom grill door. Tractors: MF255, MF265, MF275, MF285. 506319M93 Grill shell. Tractors: MF150, MF165, MF175. Industrials: 30, 31, 3165. MF-9-189

9 MISCELLANEOUS Panels & Hood Assemblies (Primed) 512556M1 Bracket assembly for side panel, Right side. Tractors: MF150 (s/n 9A15400 & up), MF165, MF175. Industrials: MF30, MF31, MF3165. 510457M2 Panel, Right side with lamp mounting holes. Tractors: MF135. Industrials: MF20, MF2135. Panel comes primed. 194842M92 Hood assembly. Tractors: MF150, MF165, MF175. Industrials: MF30, MF31, MF3165. Hood comes primed. 510458M2 Panel, Left side with lamp mounting holes. Tractors: MF135. Industrials: MF20, MF2135. Panel comes primed. 531092M91 Panel assembly front, Right side. Tractors: MF230 (prior to s/n 9A243032). Panel comes primed. 194203M91 Side panel support assembly. Tractors: MF135. Industrials: MF20, MF2135. 194422M91 Side panel support assembly. Tractors: MF135. Industrials: MF20, MF2135. 531093M91 Panel assembly front, Left side. Tractors: MF230 (prior to s/n 9A243032). Panel comes primed. 512555M91 Bracket assembly for side panel, Left side. Tractors: MF150 (s/n 9A15400 & up), MF165, MF175. Industrials: MF30, MF31, MF3165. 544416M92 Panel assembly front, left side. Tractors: MF245. Industrials: MF20C. Panel comes primed. MF-9-190

9 MISCELLANEOUS Replacement parts to fit 544417M92 Panel assembly front, right side. Tractors: MF245. Industrials: MF20C. Panel comes primed. 579175M91 Hood assembly for tractors with vertical exhaust. Tractors: MF255 (s/n 9A2823760 & up), MF265 (s/n 9A282759 & up). Hood comes primed. 535938M1 Door assembly, battery. Tractors: MF230 (prior to s/n 349239), MF235 (prior to s/n 9A229258), MF245 (prior to s/n 349239), MF265 (prior to s/n 349239). Industrials: MF20C, MF30B. Door comes primed. 579173M91 Hood assembly for tractors with horizontal exhaust. Tractors: MF255 (s/n 9A2823760 & up), MF265 (s/n 9A282759 & up), MF275 (s/n 9A284893 & up). Hood comes primed. 772804M91 Door assembly, battery. Tractors: MF230 (s/n 9A349239 & up), MF245 (s/n 9A349239 & up), MF265 (s/n 9A349239 & up). Industrials: MF20C, MF30D. Door comes primed. 532151M94 Hood assembly, Gas vertical or horizontal exhaust only. Tractors: MF255, MF265. Hood comes primed. 579237M1 Panel riser, upper on fenders. Tractors: MF245 (s/n 9A289966 & up), MF255 late production, MF265 (s/n 9A289966 & up), MF275 (s/n 289966 & up), MF285 (s/n 289966 & up). 578369M1 Panel assembly rear, Left side. Tractors: MF255 (s/n 9A66365 & up), MF265 (s/n 9A66365 & up). Panel comes primed. 532199M92 Panel assembly, Right side. Tractors: MF255, MF265, MF275, MF285. Panel comes primed. MF-9-191

9 MISCELLANEOUS Fenders Panel comes primed. To install, remove fasteners from old panel & bolt new panel in place. Panel can be shipped U.P.S. 532201M92 Panel assembly, Left side. Tractors: MF255, MF265, MF275, MF285. Panel comes primed. 180654M1WN Bolt with wing nut, for hood latch assembly & battery tie rod. Tractors: MF35, MF50, MF135. 5/16"-24 x 5" overall. 526904M1 Fender panel, dished type, less mounting brackets. For tractors without roll-over protection structure. Tractors: TE20, TO20, TO30, TO35, MF35, F40, MH50, MF50, MF65 (except orchard), MF85 std., MF135 (except vineyard & orchard), MF150, MF165, MF175, MF230, MF235 (except vineyard & orchard), MF245, MF255 (with 16" rims), MF265 std., MF275 std., MF285 std. Industrials: 20 (except turf), 20C (except turf), 30 (except turf), 30B, 35 utility, 40, 50, 50A, 202, 203, 204, 205, 2135 utility, 3165 utility, also these models with 4-post R.O.P.S., 30D, 40B, 50C. Panel comes primed. 180766M91 Bolt with special wing nut, for hood latch assembly. Tractors: TO35..320" dia., 5.25" long. 184779M92 Hood latch assembly with chrome handle. Tractors: MF20, MF25, MF40, MF50, MF50A, MH50, MF65, MF70, MF85, MF88, MF135, Super 90. Industrials: 202, 203, 204, 205, 302, 304, 356, 2135. Vintage Iron 526905M91LR Rear fender, dished type with mounting bracket. For tractors without roll-over protection structure. Tractors: TE20, TO20, TO30, TO35, MF35, F40, MH50, MF50, MF65 (except orchard), MF150, MF165, MF175, MF230, MF235 (except vineyard & orchard), MF245, MF255 (with 16" rims), MF265 std., MF275 std., MF285 std. Industrials: 20 (except turf), 20C (except turf), 30 (except turf), 30B, 35 utility, 40, 50, 50A, 202, 203, 204, 205, 2135 utility, 3165 utility, also these models with 4-post R.O.P.S., 30D, 40B, 50C. Panel comes primed. 522390M91 Fender panel assembly, Right side. Tractors: MF135, MF150 (s/n 642005072 & up), MF165 (s/n 9A1330003 & up), MF175, MF180. Industrials: MF30. Fender comes primed. MF-9-192

9 MISCELLANEOUS Replacement parts to fit Toolbox 526912M91 Fender panel assembly, Left side. Tractors: MF135, MF150 (s/n 642005072 & up), MF165 (s/n 9A1330003 & up), MF175, MF180. Industrials: MF30. Fender comes primed. 180737M1 Toolbox, fits in fender. Tractors: TO35, TE35, MF35, MF40, MF50, MF65, MF135, MF2135. Industrials: 203, 204, 205, 202 Workbull. Vintage Iron CAB INTERIOR KITS Restore your TRACTOR to "NEW" condition Gives cab a "NEW" appearance Safer, quieter, and cleaner cab environment Increases resale value Easy installation with instructions, custom fit technology FMMF1085 Floor mat. Tractors: MF1085, MF1105, MF1135, MF1155. 885895M92 Fender assembly, Left side. Tractors: MF175 (UK). Fender comes primed. Headliner Adhesive 885896M92 Fender assembly, Right side. Tractors: MF175 (UK). Fender comes primed. HLA393 Adhesive, Headliner, trim and laminating. High temperature, Contact-type adhesive, 1-5 min. work time, Unusually high initial or Green strength. MF-9-193

9 MISCELLANEOUS Gas Struts Application Strut Tractors: MF550, MF560, MF565, MF575, MF590, MF592, MF595, 3384671M1 MF2620, MF2625, MF2640, MF2645, MF2675, MF2680, MF2685, MF2705, MF2720, MF2725, MF2745, MF2775, MF2805. Tractors: MF230, MF231, MF233, MF234C, MF234CF, MF234S, 3476187M1 MF235, MF240, MF240S, MF243, MF245, MF250, MF253, MF254, MF254S, MF255, MF260, MF261, MF263, MF263T, MF264T, MF264TCF, MF264TS, MF265, MF273, MF274, MF274C, MF275, MF275E, MF283, MF284, MF284S, MF285S, MF290, MF293, MF294, MF298, MF265, MF342, MF350, MF352, MF355, MF360, MF362, MF365, MF372N, MF375, MF382N, MF390, MF396, MF398, MF399. Tractors: MF3050, MF3055, MF3060, MF3065, MF3065S, MF3070, 3389556M2 MF3075, MF3080, MF3085, MF3090, MF3095, MF3115, MF3120, MF3120T, MF3125, MF3140, MF3610, MF3630, MF3635, MF3645, MF3650, MF3655, MF3660, MF3670, MF3680, MF3690. Tractors: MF4215, MF4220, MF4225, MF4225HV, MF4235, MF4240, 3805354M1 MF4245, MF4255, MF4260, MF4265, MF4270, MF4315, MF4320, MF4325, MF4335, MF4345, MF4355, MF4360, MF4365, MF4370. Tractors: MF6110, MF6120, MF6130, MF6140, MF6150, MF6160, 3902140M1 MF6170, MF6180, MF6190, MF6235, MF6245, MF6255, MF6260, MF6265, MF6270, MF6280, MF6290, MF8110, MF8120, MF8130, MF8140, MF8150, M 8160, MF8170, MF8180, MF8210, MF8220, MF8240, MF8240TRA, MF8250, MF8250TRA, MF8260, MF8260TRA, MF8270, MF8270TRA, MF8280, MF8280TRA. Tractors: MF233, MF253, MF263, MF273, MF283, MF293, MF333, 3103958M1 MF353, MF354, MF363, MF363L, MF363S, MF364, MF373, MF374, MF383, MF383S, MF384, MF393, MF394AP, MF3050, MF3055, MF3060, MF3065, MF3065S, MF3070, MF3075, MF3080, MF3085, MF3090, MF3095. Tractors: MF230, MF231, MF233, MF234C, MF235, MF240, MF243, 1897726M91 MF244CF, MF245, MF250, MF253, MF254, MF254C, MF255, MF260, MF261, MF263, MF263T, MF264T, MF265, MF273, MF274, MF275, MF283, MF284, MF285, MF290, MF293, MF294, MF298, MF265, MF342, MF350, MF352, MF355, MF360, MF362, MF365, MF372N, MF375, MF382N, MF390, MF396, MF398, MF399. Tractors: MF4215, MF4220, MF4225, MF4235, MF4240, MF4245, 3901826M91 MF4255, MF4260, MF4265, MF4270, MF4315, MF4320, MF4325, MF4335, MF4335HV, MF4345, MF4355, MF4360, MF4365, MF4370. Tractors: MF342, MF350, MF352, MF355, MF360, MF362, MF365, 3478319M2 MF372N, MF375, MF382N, MF390, MF396, MF398, MF399. Tractors: MF6110, MF6120, MF6130, MF6140, MF6150, MF6160, 3902121M3 MF6170, MF6180, MF6190, MF6235, MF6235HV, MF6245, MF6245HV, MF6255, MF6255HV, MF6260, MF6265, MF6270, MF6280, MF6290, MF8110, MF8120, MF8130, MF8140, MF8150, MF8160, MF8170, MF8180, MF8210, MF8220, MF8240, MF8240TRA, MF8250, MF8250TRA, MF8260, MF8260TRA, MF8270, MF8270TRA, MF8280, MF8280TRA. Tractors: MF154, MF174, MF184, MF194, MF233, MF253, MF263, 3103957M1 MF273, MF283, MF293, MF333, MF353, MF354AP, MF363, MF364, MF373, MF374, MF383, MF384, MF393, MF394. Type Overall Length Rear Window 19.6875" Rear Window 19.65" Rear Window 30.905" Rear Window 19.231" Rear Window 23.11" Rear Window 14.15" Roof Hatch 8.465" Roof Hatch 8.41" Door 9.83" Door 8.84" Door 12.38" Piston Stroke 8.875" 10.22" 13.78" 7.874" 10.039" 6.88" 2.756" 4.36" 4.72" 4.32" 6.29" End Type Ball & Socket Clip-on ball joint sockets Ball & Socket Clip-on ball joint sockets Clip-on ball joint sockets Eyelets Steel eyelet and 6mm screw rod end fitting Eyelet and screw rod end Ball & Socket Threaded female ball joint Eyelets MF-9-194

9 MISCELLANEOUS Replacement parts to fit Replacement Paint for Massey Ferguson *Additional colors available direct from factory: Flint Gray - fast dry TP320FGAL Massey Harris Brown TP335QT TP230GAL Gray Gallon Massey Harris Red TP340GAL TP340QT TP340SP TP230QT TP230SP Quart Spray Flint Gray Metallic Massey Harris Straw Yellow TP345GAL TP345QT TP345SP TP320GAL TP320QT Gallon Quart Miscellaneous Paint TP320SP Spray Silver Gray TP750GAL Gallon TP750QT MF French Silver Mist Quart TP750SP Massey Ferguson French Silver Mist - spray Red TP300GAL Gallon Satin Black TP300QT Quart TP225GAL Gallon TP300SP Spray TP225QT Quart Industrial Yellow TP225SP Spray TP540GAL Gallon Aluminum TP540QT Quart TP312GAL Gallon TP312QT Quart TP312SP Spray White Gloss TP462GAL Gallon TP462QT Quart TP462SP Spray Black Gloss TP550GAL Gallon TP550QT Quart TP550SP Spray MF-9-195

9 MISCELLANEOUS Primer Acrylic Hardner TP2700GAL TP2700QT TP2700SP TP2710GAL TP2710SP TP2720GAL Gray Gallon Quart Spray White Gallon Spray Yellow Gallon TP12HP TP12P Acrylic hardener, lead free. For alkyd gloss tractor and implement enamel, 8 oz. can. Improves initial dry time and hardness development. Use with slow dry alkyd base tractor and implement gloss enamel. Not compatible with fast dry enamel or other paints Acrylic hardener, 16 oz. can, lead free. For alkyd gloss tractor and implement enamel. Improves initial dry time and hardness development. Use with slow dry alkyd base tractor and implement gloss enamel. Not compatible with fast dry enamel or other paints. TP2720QT Quart TP2720SP Spray Red TP3987GAL Gallon TP3987QT Quart TP3987SP Spray MF-9-196

9 MISCELLANEOUS Replacement Decals for Massey Ferguson Replacement parts to fit D-MF265 Model MF265. Contains 4 pieces. D-MF135 Model MF135. Contains 6 pieces. D-MF275 Model MF275. Contains 4 pieces. D-MF165 Model MF165. Contains 6 pieces. D-MF290 Model MF290. Contains 4 pieces. D-MF240 Model MF240. Contains 2 pieces. D-MF35 Model MF35. Contains 5 pieces. D-MF245H Model 245. Contains 4 pieces. D-MF35 Model MF35. Contains 5 pieces. D-MF255H Model 255. Contains 4 pieces. D-MF65 190139M1 Model MF65. Contains 5 pieces. Hood emblem, Massey Ferguson triangle. Tractors: MF35, MF35, MF65. MF-9-197

9 MISCELLANEOUS Seat Assembly Seat Cushions & Backrests 533813M96 One piece black seat assembly with vinyl cover formed over foam cushion on a steel frame. Has holes for drainage & welded on mounting brackets. Replaces 533813M91 thru 533813M95. Tractors: MF135, MF230, MF235, MF245, MF255, MF265, MF275, MF285. Industrials: 20C, 30B, 30D, 40B, 50C & 50D. Seat Cushion for Combines BR204 MFCC12 Complete backrest assembly. Gray vinyl with red trim, 2" foam with holes and wing nuts for easy mounting and height adjustment. Tractors: TEA20, TE20, TO20, MF25, MF30, TO30, MF31, MF35, TO35, MF35, MF50, MF50A, MF65, MF85, MF88, MF98, MF135, MF150, MF178, MF185, MF230, MF235, MF240, MF245, MF250, MF283. Industrials: MF20C, MF20D, MF30, MF40. Complete seat cushion assembly. Gray vinyl with red trim, 4-1/2" foam and attached strap to fasten seat cushion under frame. Tractors: TEA20, TE20, TO20, MF25, MF30, TO30, MF31, MF35, TO35, MF35, MF50, MF50A, MF65, MF85, MF88, MF98, MF135, MF150, MF178, MF185, MF230, MF235, MF240, MF245, MF250, MF283. Industrials: MF20C, MF20D, MF30, MF40. JT77B Seat cushion, black (19-1/2" x 14-5/8"). Durable weatherproof black leatherette cover, steel corners. FC810 Seat cushion and backrest assembly complete. Consists of one BR204 & MFCC12. Gray with red trim. Tractors: TEA20, TE20, TO20, MF25, MF30, TO30, MF31, MF35, TO35, MF35, MF50, MF50A, MF65, MF85, MF88, MF98, MF135, MF150, MF178, MF185, MF230, MF235, MF240, MF245, MF250, MF283. Industrials: MF20C, MF20D, MF30, MF40. BR205 Complete backrest assembly. Black vinyl with black trim, 2" foam with holes and wing nuts for easy mounting and height adjustment. Tractors: MF35, MF50, MF60, MF135, MF140, MF235, MF245, MF250, MF283, MF303E, MF1030. Industrials: MF202, MF203, MF204, MF3357. MFCC13 Complete seat cushion assembly. Black vinyl with black trim, 4-1/2" foam and attached strap to fasten seat cushion under frame. Tractors: MF35, MF50, MF60, MF135, MF140, MF235, MF245, MF250, MF283, MF303E, MF1030. Industrials: MF202, MF203, MF204, MF3357. FC811 Seat cushion and backrest assembly complete. Consist of one BR205 & MFCC13. Black vinyl with black trim. Tractors: MF35, MF50, MF60, MF135, MF140, MF235, MF245, MF250, MF283, MF303E, MF1030. Industrials: MF202, MF203, MF204, MF3357. MF-9-198

9 MISCELLANEOUS Replacement parts to fit Complete Seat Cushions, Backrest Inlays, & Covers Three-Pieces Seat Assembly for MF1100, MF1130 1041995M91 1024170M91 1032434M91 1042526M91 1043314M92 Fits all models with Keystone seats Cushion assembly, gray. Tractors: MF150, MF165, MF175, MF180, MF1080. Cushion cover, grey. Fits all models with keystone seats. Zippered to form fit the old cushion. Has bottom strap for multiple application. Tractors: MF150, MF165, MF175, MF180 & MF1080 (early production models). Formed backrest, grey. 23-1/8" bolt centers. Fits all models with keystone seats. Tractors: MF150, MF165, MF175, MF180 (early production). Formed backrest, grey. 21-7/8" bolt centers. Tractors: MF150, MF165, MF175, MF180 (late production). Formed backrest, black. Tractors: MF50 (s/n 533414 & up), MF65 (s/n 692932 & up), and MF150, MF165, MF175, MF180 (all with s/n 9A136826 & up); MF255, MF265, MF275, MF285. Industrials: 31. Replaces 1032434M91. 1031158M91 1031155M91 1031153M91 181313M91 825608M1 Upper backrest. Tractors: MF1100, MF1130 Wrap around arm rest. Tractors: MF1100, MF1130. Seat cushion. Tractors: MF1100, MF1130 Seat Parts Bucket seat pan (metal). Tractors: 35, 40, MF35, MF50, MF65 Utility, MF85, MF88, MF95, MF130, MF135, MF150, MF180, MF230, MF235. Industrial: 30. Seat spring. Tractors: TE20, TEA20, TO20, TO30, FE35, F40, MF35, F40, F50. Massey Ferguson Seat Riser 1050547M92 Seat cushion assembly, black. Tractors: MF50 (s/n 533414 & up), MF65 (s/n 692932 & up), MF150, MF165, MF175, MF180 (all with s/n 9A136826 & up); MF255, MF265, MF275, MF285. Industrials: 31. Replaces 1032168M91 1043315M91. 1674414M93 Seat riser, for mounting TISCO suspension seats TS1050 and TS1050AT. Use if additional clearance is needed between seat base and lift linkage when seat is moved to most rearward position. Can also be used as replacement riser for OEM production seats. Tractors: MF240, MF290, MF298. Industrials: 40E, 50E. MF-9-199