Owner s Manual & Safety Instructions Save This Manual Keep this manual for the safety warnings and precautions, assembly, operating, inspection, maintenance and cleaning procedures. Write the product s serial number in the back of the manual near the assembly diagram (or month and year of purchase if product has no number). Keep this manual and the receipt in a safe and dry place for future reference. Swing Arm Magnifying Lamp Visit our website at: http://www.harborfreight.com Visit our website at: http://www.harborfreight.com Email our technical support at: tech@harborfreight.com When unpacking, make sure that the product is intact and undamaged. If any parts are missing or broken, please call 1-800-444-3353 as soon as possible. Email our technical support at: tech@harborfreight.com ITEM 69515 ITEM 69590 Copyright 2012 by Harbor Freight Tools. All rights reserved. No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools. Diagrams within this manual may not be drawn proportionally. Due to continuing improvements, actual product may differ slightly from the product described herein. Tools required for assembly and service may not be included. Read this material before using this product. Failure to do so can result in serious injury. Save this manual.
WARNING SYMBOLS AND DEFINITIONS This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety messages that follow this symbol to avoid possible injury or death. Indicates a hazardous situation which, if not avoided, will result in death or serious injury. Indicates a hazardous situation which, if not avoided, could result in death or serious injury. Indicates a hazardous situation which, if not avoided, could result in minor or moderate injury. Addresses practices not related to personal injury. IMPORTANT SAFETY INFORMATION Read all safety warnings and instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury. Save all warnings and instructions for future reference. 1. Use 60 Watt or smaller, 120 Volt, type A19 bulb. 2. Risk of fire. Only install lamp arm into clamp slot that is positioned vertically. Otherwise lamp arm may fall out of slot and cause a fire while turned on. 3. Do not leave lamp unattended when turned on. Supervise children when lamp is turned on. 4. Use in a dry location. 5. Do not use near flammable materials. 6. Read manual before set up and/or use. 7. Inspect before use. Do not use if parts are loose or damaged. 8. This product is not a toy. Do not allow children to play with or near this item. 9. Use eye protection. Wear ANSIapproved impact safety goggles when setting up this product. 10. Maintain products with care. Keep the Lamp clean for better and safer performance. Inspect the components periodically. If damaged, have it repaired by a qualified technician. 11. Avoid accidental burns. Do not touch the Bulb (not included) or the Aluminum Reflector while the Lamp is turned on. Turn off the Lamp and wait until the Bulb and Reflector are completely cool before touching. 12. Do not operate the Lamp if it has a missing or damaged Aluminum Reflector. Page 2 For technical questions, please call 1-800-444-3353. Item 69515
13. Cover the Magnifying Glass with a cloth if there is any chance that light from a window or bright light may shine on it for any length of time. Magnifying glasses can cause fires if light is directed through them at flammable surfaces. 14. WARNING: Handling the cord on this product will expose you to lead, a chemical known to the State of California to cause cancer, and birth defects or other reproductive harm. Wash hands after handling. (California Health & Safety Code 25249.5, et seq.) 15. The warnings, precautions, and instructions discussed in this instruction manual cannot cover all possible conditions and situations that may occur. It must be understood by the operator that common sense and caution are factors which cannot be built into this product, but must be supplied by the operator. Save these instructions. Item 69515 For technical questions, please call 1-800-444-3353. Page 3
Functional Description Specifications Electrical Requirements 120 V~ / 60 Hz / 60 W Power Cord 5'L x 18AWG Clamp Capacity 2" Required Bulb (Not Included) 60 Watt or Smaller 120 Volt, A19 Magnifying Lens 2x Magnification x 4" Diameter Components and Controls Lock Knob Swivel Hinge Lamp Socket (under housing) ON/OFF Switch (on other side) Lock Knob Magnifying Glass Lock Knob Slots for Lamp Clamp Lower Arm Knob Figure A Page 4 For technical questions, please call 1-800-444-3353. Item 69515
Setup Instructions Read the entire Important Safety Information section at the beginning of this document including all text under subheadings therein before set up or use of this product. 1. The Clamp for the Lamp has two slots to insert the Lamp Arm Rod so the unit can be mounted on a table top or to a vertical surface. 2. Choose a location for the Lamp near the work area and route the power cord along a safe route to avoid a tripping hazard. 3. Attach the Clamp to a table or other sturdy surface 2" thick or less. Note: If needed, place a scrap of rubber or some other non-slip protective material (not included) on the table where you will secure the clamp to protect the table from becoming marked by the clamp. 4. To attach the Clamp: a. Loosen the Knob at the bottom of the Clamp and slide the Lower Arm down so the Clamp will fit the Table. b. Slide the Lower Arm of the clamp under the table and position the top of the Clamp on top, directly over the Lower Arm. c. Tighten the Knob until the clamp is secure. 5. Slide the Rod at the end of the Lamp Arm Assembly into the slot positioned vertically on the Clamp. 6. Thread a light bulb (not included) into the Lamp Socket. Note: Use a 60 Watt or smaller 120 Volt, A19 bulb. 7. Loosen, then tighten the Lock Knobs on the Arm Assembly to adjust the location of the Lamp. 8. Tilt the Lamp Head at the Swivel Hinge as needed for best use. Item 69515 For technical questions, please call 1-800-444-3353. Page 5
Operation Read the entire Important Safety Information section at the beginning of this document including all text under subheadings therein before set up or use of this product. 1. Plug the Power Cord into a 120 V~ / 60 Hz outlet. 2. Position the Lamp as needed for the task. 3. Turn the Power Switch clockwise to turn the light on. 4. When finished working with the Lamp turn the Power Switch clockwise to turn the light off. CAUTION! Wait for the unit to cool down before touching. The light and Reflector will be hot from the heat of the bulb. WARNING! Cover the Magnifying Glass with a cloth if there is any chance that light from a window or bright light may shine on it for any length of time. Magnifying glasses can cause fires if light is directed through them at flammable surfaces. Maintenance Procedures not specifically explained in this manual must be performed only by a qualified technician. To prevent SERIOUS injury from TOOL FAILURE: Do not use damaged equipment. If abnormal noise or vibration occurs, have the problem corrected before further use. Cleaning, Maintenance, and Lubrication 1. BEFORE EACH USE, inspect the general condition of the tool. Check for: leaking, swollen, or cracked batteries, loose hardware, misalignment or binding of parts, cracked or broken parts, and any other condition that may affect its safe operation. 2. After Use, wipe external surfaces of the tool with clean cloth. 3. Replace the light bulb as needed. Page 6 For technical questions, please call 1-800-444-3353. Item 69515
Parts List Part Description Qty 1 Shade 1 2 Magnifying Glass 1 3 Rubber Clip 4 4 Screw 4 5 Socket 1 6 Insulating Sleeve 2 7 Reflector 1 8 Screw 3 Part Description Qty 9 Lock Pin 1 10 Cap 1 11 Spacer 2 12 Spindle Link 1 13 Arm Assembly 1 14 Clamp Assembly 1 15 Power Cord 1 Record Serial Number Here: Note: If product has no serial number, record month and year of purchase instead. Note: Some parts are listed and shown for illustration purposes only, and are not available individually as replacement parts. Item 69515 For technical questions, please call 1-800-444-3353. Page 7
Limited 90 Day Warranty Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase. This warranty does not apply to damage due directly or indirectly, to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities, criminal activity, improper installation, normal wear and tear, or to lack of maintenance. We shall in no event be liable for death, injuries to persons or property, or for incidental, contingent, special or consequential damages arising from the use of our product. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation of exclusion may not apply to you. This warranty is expressly in lieu of all other warranties, express or implied, including the warranties of merchantability and fitness. To take advantage of this warranty, the product or part must be returned to us with transportation charges prepaid. Proof of purchase date and an explanation of the complaint must accompany the merchandise. If our inspection verifies the defect, we will either repair or replace the product at our election or we may elect to refund the purchase price if we cannot readily and quickly provide you with a replacement. We will return repaired products at our expense, but if we determine there is no defect, or that the defect resulted from causes not within the scope of our warranty, then you must bear the cost of returning the product. This warranty gives you specific legal rights and you may also have other rights which vary from state to state. 3491 Mission Oaks Blvd. PO Box 6009 Camarillo, CA 93011 (800) 444-3353