Directionl Control Vlves Solenoid Operted RE3-06 Size D 06 (03) 350 br (5076 SI) 80 L/min(21 GM) Size D 06 (03) p mx 320 br (4641SI) ccording to CSA 80 L/min(21 GM) HA 4010 11/2011 Replces HA 4010 12/2009 4/3-, 4/2- wy directionl control vlves Solenoids cn be turned round their xis to ny position Four-lnd spool - reduced functionl dependence on fluid viscosity ush button mnul override Instlltion dimensions to DIN 24 340 / ISO 4401 / CETO R121-H Subpltes see dt sheet HA 0002 CSA Upon request Functionl Description The RE3 directionl control vlves consist of housing (1), control spool (5) with two centering springs (4) nd cylindricl operting solenoids (2, 3). The three-position directionl control vlves re fitted with two solenoids nd two springs. Two-position directionl control vlves hve either one solenoid nd one return spring or two solenoids nd detent ssembly. The operting solenoids re DC solenoids. For AC supply the solenoids re provided with rectifiers which re integrted in the DIN connector socket s prt of the solenoid. The connectors (6, 7) cn be turned by 90. By loosening the nut (8), the solenoids cn be turned or replced without interfering with ny sels of the vlve. In the cse of solenoid mlfunction or power filure, the spool of the vlve cn be shifted by mnul override (9), provided the pressure in T-port does not exceed 25 br. The vlve housing (1) is phosphte coted nd the solenoids (2, 3) re zinc coted. A B T A B b 1
HA 4010 Ordering Code RE3-06 / Directionl Control Vlves Solenoid Operted Vlve size Number of vlve positions two positions 2 three positions 3 no designtion V Sensing of the end position no designtion without sensor S1 normlly-open sensor to 50 br (725SI) S2 normlly-open sensor to 210br (3045 SI) S4 normlly-closed sensor to 50br (725 SI) Sels NBR FM (Viton) Spool symbols see the tble spool symbols Rted supply voltge of solenoids (t the coil terminls) 12 V DC / 2.72 A 01200 24 V DC / 1.29 A 02400 205 V DC / 0.15 A 20500 230 V AC / 0.17 A / 50 (60) Hz 23050 no designtion D1 D2 D3 D4 D5 Orifice in port without orifice 1.0 mm (0.039 inch) 1.5 mm (0.059 inch) 2.0 mm (0.079 inch) 2.2 mm (0.087 inch) 2.5 mm (0.098 inch) The AC coils correspond with E5 type CSA Upon request Soft Shift - Spool speed control orifice no designtion without dmping orifice 0.7 mm (0.03 inch) in solenoid T1 Type of solenoid coil with terminl for the connector, EN 1745301-803 with integrted quenching diode nd terminl for the connector, EN 1745301-803 with AM-Junior-Timer-connector with integrted quenching diode nd terminl for AM-Junior-Timer connector with integrted rectifier nd terminl for the connector, EN 1745301-803 Other coils on demnd see ctlog HA8007 E1 E2 E3A E4A E5 no designtion N1 N2 N3 Mnul overide Stndrd covered with retining nut covered with rubber boot with detent ssembly Note: Connector of the position sensor is not supplied (see ordering number on pge 10) FOR REFERRED TYES SEE BOLD TYING IN ORDERING CODE, FUNCTIONAL SYMBOLS AND TABLE OF REFERRED TYES ON AGE 10 2
Technicl Dt Type Symbol Crossover Type Symbol Crossover HA 4010 Vlve size mm (US) D 06 (03) Mximum flow L/min (GM) see p-q chrcteristics Mx. operting pressure t porte, A, B br (SI) stndrd 350 (5076), ccording to CSA 320 br (4641SI) Mx. operting pressure t port T br (SI) 50 (725) for version S1, S4 nd 210 (3000) for version S2 ressure drop br (SI) see p-q chrcteristics Hydrulic fluid Hydrulic oils of power clsses (HL, HL) to DIN 51524 Fluid temperture rnge for NBR sels C ( F) -30... +80 (-22... +176) Fluid temperture rnge for FM sels C ( F) -20... +80 (-4... +176) Ambient temperture mx. C ( F) +50 (+122) Viscosity rnge mm 2 /s (SUS) 20... 400 (98... 1840) Mximum degree of fluid contmintion Clss 21/18/15 to ISO 4406 Mx. llowble voltge vrition % DC: ±10 AC: ±10 Mx. switching frequency h -1 15 000 Switching time, on: t =32 mm 2.s -1 (156 SUS) ms DC: 30... 50 AC: 30... 40 Switching time, off: t =32 mm 2.s -1 (156 SUS) ms DC: 10... 50 AC: 30... 70 Duty cycle % 100 Service life cycles 10 7 Enclosure type to EN 60 529 I 65 Weigt - vlve with 1 solenoid - vlve with 2 solenoids Mounting position Spool Symbols kg (lbs) 1.6 (3.52) 2.2 (4.84) unrestricted 3
HA 4010 p-q Chrcteristics Mesured t = 32 mm 2 /s (156 SUS) Operting limits for mximum hydrulic power trnsferred by the directionl vlve. For respective spool type - see spool symbols. Operting pressure p [br (SI)] Flow Q [L/min (GM)] Z11 1 C11 7 H11 4 11 1 Y11 3 L21 6 B11 9 Y41 7 Z21 1 C41 6 F11 6 R11 4 R21 5 A51 6 51 1 Y51 3 C51 7 Z51 1 Z71 8 Z81 8 Z91 8 R31 6 H51 8 F51 8 X11 4 K11 8 N11 8 X25 11 J15 1 J75 10 p-q Chrcteristics Mesured t = 32 mm 2 /s (156 SUS) ressure drop p [br (SI)] ressure drop p relted to flow rte. Flow Q [L/min (GM)] -A -B A-T B-T -T Z11 2 2 3 3 C11 5 5 5 6 3 H11 2 2 2 3 3 11 1 1 3 3 Y11 2 2 2 2 L21 2 2 3 3 B11 2 2 3 3 Y41 3 3 3 3 Z21 2 3 C41 4 4 5 F11 1 2 3 3 R11 2 2 3 3 R21 2 2 3 3 A51 2 2 51 1 3 Y51 2 2 C51 2 3 4 Z51 2 3 Z71 3 3 Z81 3 3 Z91 3 3 3 R31 2 3 H51 2 3 F51 2 3 X11 2 2 3 3 K11 2 3 N11 2 2 3 3 X25 3 3 3 J15 2 2 3 3 J75 2 2 4
Vlve Dimensions Dimensions in milimeters (inches) HA 4010 Vlve with two solenoids 12,5 (0.492) 40,5 (1.594) 33 (1.231) 31 (1.220) 7 (0.276) 5,1 (0.201) 0,75 (0.030) 30,2 (1.189) 21,5 (0.846) 12,7 (0.512) A T B 3 (0.12) 6 32,5 (1.280) 45,5 (1.791) 25,9 (1.019) 15,5 (0.610) 73,5 (2.894) 68 (2.677) 52 (2.047) 215 (8.465) 8 7 4 12 (0.472) 9,5 (0.374) 49,3 (1.940) 5,3 (0.209) b 45 (1.772) 56,5 (2.224) 92,5 (3.641) 37,3 (1.468) 24 (0.945) 1,25 (0.049) 1,4 (0.055) 3 1 5 2 9 3 8 (0.315) 12,4 (0.488) Vlve with one solenoid "" Spool symbols R11, R21, A51, 51, Y51, Z51, C51, Z71, Z81, Z91, R31, H51, F51, X25 8 (0.315) 1 Solenoid 2 Solenoid b 3 Mnul override 4 Nme plte 5 Squre ring (4 pcs.) 9.25 x 1.68 supplied with vlve 6 4 mounting holes 7 Electricl connecto, EN 1745301-803 8 Spce required to remove connector 9 Solenoid fixing nut [Nut torque 2.95 ft-lbs (4 Nm)] 149,5 (5.886) 0.0004 / 4.0 [ in 0.01 / 100 [ mm Rmx 6,3(248) ( 0,8(32) [ m in) ] [ [ Vlve with one solenoid "b" Spool symbols X11, Z11, C11, H11, K11, N11, F11 Required surfce finish of interfce b 5
HA 4010 Type of the Solenoid Coil Designtion Dimensionl sketch Description E1 Solenoid coil with terminl for the electricl connector, EN 1745301-803. E2 Solenoid coil with integrted quenching diode (bipolr trnsil diode) nd terminl for the electricl connector, EN 1745301-803. E3A Solenoid coil with terminl for AM-Junior-Timer electricl connector. E4A Solenoid coil with integrted quenching diode (bipolr trnsil diode) nd terminl for AM-Junior-Timer electricl connector. E5 Solenoid coil with integrted rectifier nd terminl for the electricl connector, EN 1745301-803. Mnul Override no designtion Dimensions STANDARD Type N1 Dimensions CLOSED NUT Stndrd model of the mnul override. Stndrd retining nut of the solenoid. RUBBER BOOT Mnul override with retining nut. Cn be used fter removing nut. DETENT ASSEMBLY Type N2 Dimensions Type N3 Dimensions 32 (1.259) 38 (1.259) 45 (1.772) Mnul override protected by rubber boot. Mnul override holds the spool in the shiftet position. 6
Spool Speed Control Orifice Type Dimension Description HA 4010 T1 2 1 Importnt: This directionl vlve provides control spool soft shifting by mens of orifice situted in the solenoid rmture.to ensure the proper function of the vlve, perfect ir bleeding of the solenoid is required (by us of bleeding plug (1). The plugs re ccessible fter removing the rubber boot (2) from the solenoid retining nut (3). 3 Switching times Switching time, on nd off ms 300... 800 The switching times shown re vlid for viscosity = 32 mm 2 /s (156 SUS) nd nominl voltge. They re dependent upon working pressure nd flow rte of the directionl control vlve Orifice in -ort Type D mm (inch) Dimensions Description D1 1,0 (0.039) D2 1,5 (0.059) D3 2,0 (0.079) D4 2,0 (0.087) Sel ring -port orifices limit the flow into the directionl control vlve. Attention: When the orifice in port is dditionlly mounted the stndrd used squre ring NBR is replced with O-ring from Viton. D5 2,0 (0.098) 7
HA 4010 Spool Ship osition Sensor S1, S2 - Circuit digrm of the normlly-open sensor N Sensor Connector S4 - N Sensor Circuit digrm of the normlly-closed sensor 2 Connector The proximity sensor trnsforms the spool position into n electricl step signl. It cn be used with directionl control vlves with one or two solenoids. Technicl Dt of the Sensor S1, S4 S2 Rted power supply voltge V 24 DC ower supply voltge rnge V 10... 30 DC Rted current ma 200 Enclosure type of sensor to EN 60529 I 67 Mx. operting pressure br (SI) 50 (725) 210 (3046) Switching frequency Hz 1000 Ambient temperture rnge C ( F) -25... +80 (-13... +176) Technicl Dt of the Connector ower supply voltge rnge V 10... 30 DC Ambient temperture rnge C ( F) -25... +80 (-13... +176) Indiction yellow LED Two-osition Directionl Control Vlve Dimensions in millimeters (inches) Signl of solenoid (b) Signl of sensor S (Sb) LED S1, S2 - normlly-open S4 - normlly-closed S1, S2 S4 0 1 0 ON OFF 1 0 1 OFF ON S (Sb) (b) Three-osition Directionl Control Vlve Dimensions in millimeters (inches) Signl of solenoid Signl of sensor S (Sb) LED S1, S2 - normlly-open S4 - normlly-closed S1, S2 S4 b S Sb S Sb S - LED Sb - LED S - LED Sb - LED 0 0 1 1 0 0 ON ON OFF OFF 1 0 0 1 1 0 OFF ON ON OFF S Sb b 8
Spre rts 1 Electricl connector 2 Solenoid coil 3 Nut with sel 4 Orifice in port with sel ring 5 Sensor 6 Connector of position sensor with LED 7 Sel kit 8 Mounting bolts A 8 B 1 2 HA 4010 1 2 6 5 b T 3 A B Solenoid coil Coil type Solenoid type E1 E2 E3A E4A E5 Order number 01200 16211400 24156100 24159600 24159700 01200* 24154300 - - - 02400-24157400 24159800 24159900 02400* 24154400 20500-23500 18849000 23500* 24154600 *CSA Upon request Solenoid retining nut with sel Type of the nut Sel ring Order number Stndrd nut 15844600 Closed nut 15844700 22 x 2 Nut with rubber boot 15844800 Nut with detent ssembly 15844900 Connector of position sensor Type designtion Model Mx. input voltge Ordering number K02 connector of position sensor with LED 10...30 V DC 17364800 S1 normlly-open sensor 10...30 V DC 16688500 S2 normlly-open sensor 10...30 V DC 18961900 S4 normlly-closed sensor 10...30 V DC 20725300 Orifice in -port Type D mm (inch) Sel ring Order number D1 1,0 (0.039) 15845600 D2 1,5 (0.059) 15845700 D3 2,0 (0.079) 9.25 x 1.75 15845800 D4 2,2 (0.087) 15846000 D5 2,5 (0.098) 15845900 Bolt kit Dimensions, quntity Bolt torque Order number M5 x 45 DIN 912-10.9 (4 pcs.) 8.9 Nm (6.6 ft-ibs) 15845100 Sel kit Type Dimensions, quntity Order number Stndrd - NBR70 9,25 x 1,68 x 1,68 (4 pcs.) 17 x 1.8 (2 pcs.) 15845200 Viton 9,25 x 1,78 (4 pcs.) 17,17 x 1,78 (2 pcs.) 15845400 4 7 9
HA 4010 Electricl connector, EN 1745301-803 Type Connector A grey Connector B blck Ordering number K1 16202200 16202100 K5 16202600 16202500 K2 16202800 16202700 K3 16202400 16202300 K4 16203000 16202900 Electricl Connector, EN 175301-803 K1 K5 K2 K3 K4 Connector B (blck) Connector A (grey) Connector B (blck) Connector A (grey) Connector B (blck) Connector A (grey) Connector B (blck) Connector A (grey) Connector B (blck) without rectifier - M16x1.5 ( bushing bore 6-8 mm) without rectifier - M16x1.5 ( bushing bore 4-6 mm) without rectifier with LED nd quenching diode - M16x1.5 ( bushing bore 6-8 mm) with rectifier - M16x1.5 ( bushing bore 6-8 mm) with rectifier with LED nd quenching diode - M16x1.5 ( bushing bore 6-8 mm) 230 V AC/DC 230 V AC/DC 12... 24 V DC 230 V AC 230 V AC Recommended solenoid coils used with electrcil connector with rectifiers - type designtion K3, K4 Rted supply source voltge (permissible rted voltge vrition ±10 %) Type designtion of the solenoid voltge 230 V AC / 0.17 A / 50 (60) Hz 20500 referred Types of Vlves Type Ordering Number Type Ordering Number RE3-062Z11/01200E1 15720300 RE3-063Y11/02400E1 15728400 RE3-063Z11/01200E1 15711300 RE3-062R11/02400E1 15731100 RE3-062Z51/01200E1 15719300 RE3-062R21/02400E1 15734500 RE3-063C11/01200E1 15712600 RE3-062A51/02400E1 15732800 RE3-062C51/01200E1 15719600 RE3-062Y51/02400E1 15737400 RE3-063H11/01200E1 15713500 RE3-062J15/02400E1 15733500 RE3-063Y11/01200E1 15714300 RE3-062Z11/23050E5 15768800 RE3-062R11/01200E1 15716000 RE3-063Z11/23050E5 15747100 RE3-062R21/01200E1 15717100 RE3-062Z51/23050E5 21262800 RE3-062A51/01200E1 15716700 RE3-063C11/23050E5 15748900 Cution! When the distributor contins two electromgnets ny of the two electromgnets cn be switched on only fter the other one switches off. The electromgnets switching time on distributors with locking rrngement must not be shorter thn 60 ms.with directionl vlves with cushioned spool shifting, the switching time must correspond with the shifting time. Distributors with other interconnections thn those shown in the ctlogue cn be supplied on request. The pckging foil cn be recycled The trnsport bse plte cn be returned to the mnufcturer. Mounting screws M5 x 45 DIN 912-10.9 or bolts must be ordered seprtely. The screws tightening torque is 8.9 Nm (6.6 ft-ibs). The mentioned dt only serve to describe the product nd in no cse re to be understood in terms of lw s gurnteed chrcteristics. ARGO-HYTOS s.r.o. CZ - 543 15 Vrchlbí Tel.: +420-499-403 111 E-mil: info.cz@rgo-hytos.com www.rgo-hytos.com 10 Subject to ltertion without notice!