DRUM STANDS & TRAILERS STRINGING EQUIPMENT CATALOGUE

DRUM STANDS & TRAILERS STRINGING EQUIPMENT CATALOGUE

DRUM STAND Model: TB Z 246 / TB Z 249 / TB Z 550 Drum stand with hydraulic drive unit suitable for drums up to Ø 3.000 mm; Drum weight: 8.000 kg up to 13.000 kg Full hydraulic operation as drum stand => uniform and wear free operation, pulling mode also possible, no run on when the machine stops Mounted drum drive => drive need not be dismounted to change the drums High quality, light drum shaft with two adjustable cones for a perfect fixing of the drum suitable for all drum types Drum drive unit: With planetary gear and hydraulic motor. The drive is activated directly on the drum shaft => high torques can be transmitted with little wear Free wheel device for an easy pull out of the rope With hydraulic quick couplings for connection with a Puller-Tensioner or other drive unit Mechanical brake system as parking brake for safely blocking the drum Cone adjustable via a hand crank => simple handling and perfect fixing of the drum Adjustable drum driving bolt => for all drum types Drum is loaded via a crane or by tilting the drum stand Stable steel frame with anchoring eyes Dismountable frame for smaller transport dimensions Hose set with quick couplings for connection with the drive unit (standard length: 15 m; or according to customer requirements) Suitable for stringing operation with helicopter => max. rope speed approx. 20 km/h Rope guidance device hydraulic driven; continuously adjustable for all drum width and rope diameter Mounted or separate engine aggregate (with gasoline or diesel engine) => independent operation, e.g. as Puller to pull in old conductor directly ATS for automatic rope pull in/out for use behind a Tensioner without additional hydraulic system Reel with detachable flange HT/TBF with big rope capacity => ideal for scrapping conductors. Maximum pull force at core Ø: 1.400 dan Biodegradable hydraulic oil Special equipment or special models (e.g. for bigger drums) on request

DRUM STAND IT Model: TB / IT Drum stand with disc-brake system and a manual hydraulic for independent loading of conductor drums For drums with a weight up to 10 to (Optional also for heavy drums) Consisting of 2 separate units => smaller transport dimensions and minimal weight Optional with hydraulic drum drive unit Drum tensioning unit: Speed continuously adjustable: 0 - ca. 6 km/h (32 U/min) With disc-brake system; operation via hand wheel Drum shaft with 2 adjustable cones The drum is fixed on each side with 4 clamp units. Optional special clamp unit for drums with 3 spokes Two manual hydraulic units for lifting and lowering the drum holding fixtures => simple loading of drums Mechanical holding device for drum lifting system; keep the load independent from the hydraulic cylinders Holding device to connect a hydraulic drum drive Hydraulic drum drive (drive torque: 2.900 Nm; weight: 77 kg) with quick locking device to connect onto the drum stand => in connection with ZECK machines, rope pull in/out is fully automatically controlled Hose set with quick coupling to connect to a drive unit (standard length: 15 m; or according to customer requirements) Special equipment for bigger drums on request 2 separate units for smaller transport dimensions; with supporting grips for an easy transport Model max. drum weight (kg) Device for drum drive max. drum Ø (mm)min. drum Ø mm max. drum width mm Length mm 244-050 2.000 no 2.000 700 1.300 1.400 180 244-200 7.000 yes 2.800 1.000 1.500 2.000 280 244-300 10.000 yes 3.200 1.500 1,650 2.200 360 Weight (kg)

DRUM CARRIER Model: TBF 70 SB Drum carrier and hydraulic drum stand suitable for drums up to Ø 3.000 mm / width 1.500 mm / weight: 7.000 kg All-purpose, as: - hydraulically activated drum stand behind a Tensioner - Drum carrier (registration up to 80 km/h) with engine aggregate for loading conductor drums independently - hydraulic Puller for direct pull in of rope Fully hydraulic operation as drum stand => uniform and wear free operation; pulling mode also possible; no run on when the machine stops Mounted drum drive => not necessary to dismount the drive to change the drums High quality, light drum shaft with two adjustable cones for a perfect fixing of the drum - suitable for all types of drum Drum drive unit: Drive torque: 2.900 Nm Speed continuously adjustable: 0-6 km/h With planetary gear and hydraulic motor. Drive is activated directly on the drum shaft (no wheel friction drive) => high torques can be transmitted with little wear Free wheel device for an easy pull out of the rope With hydraulic quick couplings for connection with a Puller-Tensioner or other drive units In connection with ZECK machines, rope pull in/out is fully automatic hydraulically controlled Mechanical brake system as parking brake for safely blocking the drum High quality, light drum shaft with Ø 76 mm, with two adjustable cones and minimal maintenance plain bearings on both sides Cone adjustable via a hand crank => easy handling and a perfect fixing of the drum Adjustable drum driving bolt => for all types of drums Engine aggregate (5 HP) for lifting and lowering the drum holding fixtures hydraulically => simple loading/unloading of drums - Drum Ø: max. 3.000 mm - Drum width: max. 1.580 mm (with 125 mm bore) - Center bore: 80-125 mm - Drum weight: max. 7.000 kg approx. 2.650 kg approx. 4.700 x 2.550 x 2.360 mm Stable steel frame optional in galvanized version Front support via robust mechanical supporting winch (with load and idle speed) Back support by 2 mechanical supporting plates Chassis: EU chassis: 2 axle chassis with spring-mounted axles, pneumatic brake system with automatic load dependent braking force, parking brake, lighting system, mudguards and registration as high-speed trailer (in Germany up to 80 km/h) Export chassis: 2 axle chassis with spring-mounted axles, pneumatic brake with manual braking force regulation and parking brake, lighting system, mudguards Stable towing bar with height adjustable towing eye with Ø 40 mm (optional according to customer requirements) Galvanized steel frame Lockable tool box Hose set with quick couplings for connection to a drive unit (standard length: 15 m; or according to customer requirements) Biodegradable hydraulic oil Big engine aggregate with electro start(17 HP; with gasoline or diesel engine) => independent operation, e.g.as Puller to pull in old conductors directly ATS for automatic rope pull in/out for use behind Tensioners without additional hydraulic system Reels with detachable flange HT/TBF with big rope capacity => ideal for scrapping conductors. Maximum pull force at core Ø: 1.400 dan Special equipment or special models on request

DRUM CARRIER Model: TBF 8020 E Drum Carrier for drums up to Ø 3.200 mm / width: 1.720 mm / weight: 8.000 kg Easy installa on of the drum by special frame design ("U-type") Easy loading by hydraulic hand pump and cylinders Drum holding system: Steel axle Ø 76 mm with 2 drum fixing devices Various holding devices for different drum-ø - Drum-Ø: max. 3.200 mm - Drum width: max. 1.720 mm - Center bore: 80-125 mm - Drum weight: max. 8000 kg approx. 1.100 kg permissible max. 9.100 kg ca. 4.000 x 2.520 x 2.300 mm delivered with detachable frame for small shipment dimensions Chassis: 1 axle with rigid axle and parking brake supporting wheel Optional: Ligthing system, mudguards Optional equipment: Engine driven hydraulic aggregate Drum drive unit (only with aggregate) additional drum holding devices for drum-ø < 1.700 mm

DRUM CARRIER Model: TB - S01 Drum carrier and hydraulic drum stand suitable for drums up to Ø 3.000 mm / width 1.500 mm / weight: 8.000 kg All-purpose as: - hydraulically activated drum stand behind a Tensioner - Drum carrier with simple chassis => only for operation at construction sites (without vehicle registration) - hydraulic Puller for direct pull in of rope Fully hydraulic operation as drum stand => uniform and wear-free operation, pulling mode also possible, no run on when the machine stops Mounted drum drive => not necessary to dismount the drive to change the drums High quality, light drum shaft with 2 adjustable cones for a perfect fixing of the drum; suitable for all types of drum Drum drive unit: Drive torque: 2.900 Nm Speed continuously adjustable: 0 - ca. 6 km/h (32 U/min) With planetary gears and hydraulic motor. Drive is activated directly on the drum shaft (no wheel friction drive) => high torques can be transmitted with little wear Free wheel device for an easy pull out of the rope With hydraulic and quick couplings for connection with a Puller- Tensioner or other drive units In connection with ZECK machines rope pull in/out is fully automatic hydraulically controlled Mechanical brake system as parking brake for safely blocking the drum High quality, light drum shaft with Ø 76 mm, with two adjustable cones and minimal maintenance plain bearings on both sides Cone adjustable via a hand crank => easy handling and perfect fixing of the drum Adjustable drum driving bolt => for all drum types Drum is loaded via a crane - Drum Ø: max. 3.000 mm - Drum width: max. 1.486 mm (with 125 mm bore) max. 1.384 mm (with 80 mm bore) - Center bore: 80-125 mm - Drum weight: max. 8.000 kg Stable steel frame with anchoring eyes Lifting rings for easy loading by crane Front support via robust mechanical supporting winch (with load and idle speed) Chassis: 1 axle chassis with rigid axle Optional: lighting system Stable towing bar with height-adjustable towing eye with Ø 40 mm (optional according to customer requirements) Hose set with quick couplings for connection with the drive unit (standard length: 15 m; or according to customer requirements) Suitable for stringing operation with helicopter => max. rope speed approx. 20 km/h Mounted or separate engine aggregate with gasoline or diesel engine) => independent operation, e.g.as Puller to pull in old conductors directly ATS for automatic rope pull in/out; for use behind Tensioners without additional hydraulic system Biodegradable hydraulic oil Special equipment or special models on request approx. 1.200 kg approx. 3.200 x 2.420 x 2.020 mm

DRUM STAND Model: TBh 18 / TBh 20 Drum stand with large disc-brake system and a manually activated hydraulic system for loading drums independently; for drums up to Ø 1.800 mm (TBh 20 up to Ø 2.000 mm) / width 1.140 mm / weight 3.000 kg High quality, light drum shaft with two adjustable cones for a perfect fixing of the drum - suitable for all drum types Optional with a connectable hydraulic drum drive Drum tensioning unit: Tensioning torque: 1.900 Nm Continuously adjustable speed: 0 - ca. 6 km/h Double acting, large disc-brake system; comfortable operation via a big hand wheel High quality, light drum shaft with Ø 76 mm, with 2 adjustable cones and minimal maintenance plain bearings on both sides Cone adjustable via a hand crank => simple handling and perfect fixing of the drum Adjustable drum driving bolt => for all drum types Manual hydraulic unit for lifting and lowering the drum holding fixtures => simple loading of drums - Drum Ø: max. 1.800 mm (TBh 18) max. 2.000 mm (TBh 20) min. 1.000 mm - Drum width: max. 1.140 mm - Center bore: 80 mm - Drum weight: max. 3.000 kg Stable steel frame with anchoring eyes Biodegradable hydraulic oil Holding device to connect a hydraulic drum drive Hydraulic drum drive (drive torque: 2.400 Nm; weight: 67 kg) with quick locking device to connect to the drum stand => in connection with ZECK machines, rope pull in/out is fully automatically controlled Hose set with quick coupling to connect to a drive unit (standard length: 15 m; or according to customer requirements) Mounted or separate engine aggregate (gasoline or diesel) => independent operation for tension rope-out or pull rope-in Rope guidance device hydraulic driven; continuously adjustable for all drum width and rope diameter Special rope grounding device Special model (e.g. mounted engine aggregate) or special equipment (e.g. for bigger drums) on request approx. 460 kg approx. 1.550 x 1.930 x 1.200 mm

DRUM STAND Model: TB 18 / 25 / 30 Drum stand with large disc-brake system; various models for drums up to Ø 1.800 mm / 2.500 mm / 3.000 mm (or according to customer requirements) High quality, light drum shaft with 2 adjustable cones for a perfect fixing of the drum - suitable for all types of drum Optional with a connectable hydraulic drum drive Drum tensioning unit: Tensioning torque: 1.900 Nm Continuously adjustable speed: 0-100 m/min (6 km/h) Double acting, large disc-brake system; comfortable operation via a big hand wheel High quality, light drum shaft with 2 adjustable cones and minimal maintenance plain bearings on both sides Cone adjustable via a hand crank => simple handling and perfect fixing of the drum Adjustable drum driving bolt => for all drum types Drum is loaded via crane or by tilting the drum stand Stable steel frame with anchoring eyes Dismountable frame for smaller transport dimensions Holding device for connecting a hydraulic drum drive Hydraulic drum drive (drive torque: 2.400 Nm; weight: 67 kg) with quick locking device to connect to the drum stand => in connection with ZECK machines, rope pull in/out is fully automatically controlled Hose set with quick coupling to connect to a drive unit (standard length: 15 m; or according to customer requirements) Special models or special equipment (e.g. for bigger drums) on request TB 18 TB 25 TB 30 TB 30/12,5 Max. drum Ø in mm 1.800 2.500 3.000 3.000 Max. drum width in mm1.150 1.470 1.650 1.800 Center bore in mm 80-125 80-125 125-140 125-140 Max. drum weight (kg)4.000 7.000 10.000 12.500 approx. 430 / 620 / 840 / 950 kg approx. 1.600 x 1.960 x 1.380 mm approx. 1.790 x 1.960 x 1.830 mm approx. 2.500 x 2.400 x 2.100 mm