ULLTIN 00/579 JUN 2016 PO S-00/00 SING K LS PO S Swing heck s are recommended for clean and dirty services such as ater, Sewage or Industrial applications. S-00/00 Swing heck s are a heavily constructed, full waterway flow area, premium design with multiple features and options. The S-00/00 is designed to handle higher flow rates, pressures and withstand shock. vailable in sizes 2-66" (50-10mm), the S-00/00 Swing heck s are available with crylonitrile- utadiene (NR), Terpolymer of thylene, Propylene and iene (PM) or luoro Rubber (KM) resilient disc seats, or cast aluminum bronze or stainless steel metal seats for durability. The body seat is long-wearing centrifugally cast aluminum bronze or Type 316 stainless steel. ody seats are available with a NR, PM or KM resilient seal. igh Strength Shaft One-piece shafts are constructed of Type 303 or 17-4 P stainless steel for high strength. Throughshaft design, with an integral retainer, prevents axial shaft movement. ull aterway low rea The valves feature a full waterway flow-through area and low head loss. The pivot point of the disc is located outside the port opening, allowing the entire disc to lift clear of the flow area. This is particularly important in sewage, slurries or other dirty service applications. ouble levis, Self-ligning isc The double clevis design securely connects the disc to the disc arm in two places. The double clevis hinge assures self-leveling and even load distribution upon closing, minimizing seat wear. The full open disc stop can be independently adjusted. The disc arm is ductile iron for high strength. Internals Removable ithout Removing from the Line Top entry design allows all internal parts, including the body seat, to be easily replaced in the field by removing the cover. The seat ring is field replaceable without the use of special tools.
losure ontrol evices ir ushion Side Mounted ylinder () or ree Open, ast lose applications, the air cushioned check valve utilizes a totally enclosed cushion cylinder externally mounted to the side of the main valve body. heavy outside lever, positively clamped to an extra-large diameter pivot shaft, forces the disc to close immediately upon pump shut down and before reverse flow takes place. The weighted lever drives the piston into the cushion chamber, 30 compressing the trapped air and creating a cushion during valve closure. ast losing ith ushion t Shut-Off Principle of Operation 1. ischarge velocity head from the pump against the disc (10) opens the disc and raises the weighted lever () outside of the valve upward. t the same time, the piston inside the cushion cylinder (20) is pulled upward, drawing free air into the cushion cylinder through the one-way control check valve (30). 2. hen reverse flow occurs against the backside of the disc (10), pressure forces the disc toward the shut-off position against the seat (5) at the same time forcing the cushion cylinder downward. Moving downward, the piston compresses the air in the cushion cylinder because the air cannot readily escape through the one-way control check valve. y restricting the air escape through the adjustable control check (30) air cushioned closing is accomplished. 3. ir cushioning is field adjustable by adjusting the flow control valve (30) for increased or decreased cushioning, or moving the weights on the pivot shaft for more or less rapid disc closure. 20 30 5 10 or Sizes 2-6" (50-150 mm) See pages 9 and 10 for lever and weight and lever and spring closure control devices. 2 2016 ezurik, Inc.
losure ontrol evices Oil ontrolled, Side Mounted ylinder (O) or ree Open, Slow lose applications, S-00 Swing heck s are available with an Oil ontrolled, Side Mounted ylinder closure control device. The totally enclosed oil cylinder is protected from the elements. Three-stage closure on valves 6-20" (150-500mm) minimizes damaging water hammer. Principle of Operation 1. ischarge velocity head from the pump causes the disc (10) to open and raises the outside weighted lever (). xcept for frictional resistance, the disc is free opening. 2. Three-stage closing is achieved by the oil dashpot/ timing valve system which minimizes damaging water hammer. ach stage is independently adjustable. a. The initial stage of closure is provided by the timing valve (45). The timing valve allows very fast closure of the disc from full open to any degree of closure. This feature greatly reduces the volume of backflow and flow reversal that occurs with on valves with only two stages of closure. Timing not supplied on sizes 2-4" (50-100mm) b. The second stage of closure is provided by the low ontrol (30) that varies speed toward final closure. c. The final stage of closure is provided by Timing internal adjustment of the cylinder (20) that controls variable speed closure to shut-off. d. dditional disc closing adjustments can be made by moving the weight on the pivot shaft. Three Stage losing haracteristics Note: Oil reservoir must be mounted vertically regardless of valve installation position. Specify mounting position when ordering. Timing in lose Position Timing not supplied Timing on sizesnot supplied on sizes 2-4" (50-100mm) 2-4" (50-100mm) 100% Open Primary ontrol (Timing ) onventional heck without ontrols To Rod nd Sizes 10-16" (0-400mm) Timing Timing low or aster losure Override Second Stage with the Timing pproximately 5% Open t 1 Min. Timing loses djustable Start of Secondary ontrol (low ontrol ) Start of Third Stage ontrol (Internal ushion djustment) Time t1 Max. onfiguration Sizes 2-6" (50-150mm) The graph shows flow rate as a function of closing time and illustrates the superiority of the PO three stage Oil ontrolled Side Mounted ylinder over two stage closure devices. Internal ushioned djustment Screw rom cap end of cylinder on other side of valve Sizes 10-16" (0-400mm) onfiguration Sizes 2-6" (50-150mm) Note: Oil reservoir must be mounted vertically regardless of valve installation position. Specify mounting position when ordering. Timing in lose Position Note: Oil reservoir must be mounted vertically regardless of valve installation position. Specify mounting position when ordering. Timing in lose Position Internal ushioned djustment Screw rom cap end of cylinder on other side of valve Sizes 10-16" (0-400mm) To Rod nd Sizes 10-16" (0-400mm) To Rod nd Sizes 10-16" (0-400mm) Timing Note: Oil reservoir vertically regardle Specify mounting Timing in lose Position onfiguration Sizes 2-6" (50-150mm) Internal ushioned djustment Screw rom cap end of cylinder on other side of valve Sizes 10-16" (0-400mm) 3
losure ontrol evices Oil ontrolled, ottom Mounted uffer (M) ottom Mounted uffers have been used successfully for decades to reduce slamming of the valve disc and resultant water hammer. or ree Open, ontrolled lose applications, S-00 Swing heck s sizes 8-66" (200-10mm) are available with an Oil ontrolled, ottom Mounted uffer closure control device. Principle of Operation 1. The unique buffer arrangement allows the valve disc (10) to open fully without interference and to close freely for approximately 90% of its stroke. 2. fter the disc is 90% closed, the disc comes in contact with the buffer rod (33). The oil hydraulic buffer makes contact with the disc and controls closure during the final 10% of the stroke. 3. The flow control valve (41) on the cylinder (39) easily adjusts closing time to suit flow conditions reducing slam, water hammer and pressure surges. The color-coded micrometer type control valve adjusts the final closure, and has a locking set screw that is used to secure the final setting. ottom Mounted uffers are recommended for larger sized valves and for vertical upward flow installations. They are also recommended where instantaneous flow reversal caused by a hydro pneumatic surge tank or open line discharge is so fast that a free closing check valve cannot shut prior to reverse flow, and therefore slams. rain Opening 10 41 33 39 Note: ashing ction utomatically leans the uffer rea 4
losure ontrol evices onvertible Swing heck s (L & LS) If hydraulic conditions exceed those anticipated, S onvertible Swing heck s can be converted in the field to closure control devices that reduce moderate or severe slam. or moderate slam, S-onvertible Lever & Spring s (LS) or S-L onvertible Lever & eight s (L) can be converted to an ir ushion Side Mounted ylinder. or severe slam, S-onvertible valves can be retrofitted in the field to Oil ontrolled Side Mounted ylinder or ottom Mounted uffer closure control devices. 5
Materials of onstruction Item escription Material 1 ody uctile Iron, STM 536 2 over uctile Iron, STM 536 5 ody Seat luminum ronze, STM 1 with crylonitrile - utadiene (NR) 316 Stainless Steel, STM 276 with crylonitrile - utadiene (NR) luminum ronze, STM 1 with Terpolymer of thylene, Propylene and iene (PM) 316 Stainless Steel, STM 276 with Terpolymer of thylene, Propylene and iene (PM) luminum ronze, STM 1 with luoro Rubber (KM) 316 Stainless Steel, STM 276 with luoro Rubber (KM) 6 isc Seat crylonitrile-utadiene (NR) Terpolymer of thylene, Propylene and iene (PM) luoro Rubber (KM) luminum ronze, STM 1 316 Stainless Steel, STM 276 9 isc rm uctile Iron, STM 536 10 isc uctile Iron, STM 536 13 Pivot Shaft Stainless Steel, Type 303, STM 582 17-4 P Stainless Steel, STM 564 Type 630 Selection Shut-Off apabilities Seat Type crylonitrile-utadiene (NR) Terpolymer of thylene, Propylene and iene (PM) luoro Rubber (KM) Pressure Ratings Size 2-66" (50-10mm) Temperature Ratings Shut-Off rip-tight Pressure 1 = 0 psi P (1720 kpa) 2 = 640 psi P (4140 kpa) ll Seats to 1 ( ) ontact application engineering if the valve is required to operate above this temperature. 02 13 09 pplicable Standards ezurik S-00/00 Swing heck s are designed and/or tested to meet the following standards: -09 Swing-heck s for aterworks Service 2-In Through 24-In (50-mm Through 0-mm) NPS MSS SP-71 Testing Gray Iron Swing heck s MSS SP-136 Testing uctile Iron Swing heck s SM 16.1 Gray Iron Pipe langes and langed ittings SM 16.5 onforms to olt Pattern and rilling 05 10 06 01 6
Selection ead Loss haracteristics for Swing heck s ead Loss in eet low in Gallons Per Minute eights & ir ushion ylinder & ottom Mounted uffer Size 2" 50mm 2.5" 65mm 3" 80mm 4" 100mm 6" 150mm 10" 0mm 16" 400mm 1 450mm 20" 500mm 24" 0mm 30" 750mm 36" 900mm 42" 1100mm " 1 eight lbs/kg 106 138 63 175 79 238 108 385 175 475 650 5 1180 536 1714 778 20 1 2721 1235 17 14 4197 1905 4 97 11830 5 150 7736 24980 11334 Size 10" 0mm 16" 400mm 1 450mm 20" 500mm 24" 0mm 30" 750mm 36" 900mm 42" 1100mm " 1 " 1400mm " 1500mm 66" 10mm eight lbs/kg 539 245 795 361 1150 522 1803 819 00 1135 3022 12 30 1634 50 4 9000 4084 11340 5146 17265 7834 000 11344 34649 15721 44300 20100 53949 24478 7
Ordering To order, simply complete the valve order code from information shown. n ordering example is shown for your reference. Style Give valve style code as follows: S = Swing heck s Size Give valve size code as follows: 2 = 2" (50mm) 18 = 1 (450mm) 2.5 = 2.5" (65mm) 20 = 20" (500mm) 3 = 3" (80mm) 24 = 24" (0mm) 4 = 4" (100mm) 30 = 30" (750mm) 6 = 6" (150mm) 36 = 36" (900mm) 8 = () 42 = 42" (1100mm) 10 = 10" (0mm) = " (1) 12 = () = " (1400mm) 14 = () = " (1500mm) 16 = 16" (400mm) 66 = 66" (10mm) ody Style Give body style code as follows: 00 = Series 00 (2-) 00 = Series 00 (16-66") nd onnection Give end connection code as follows: 1 = langed SM 1/150 2 = langed SM 0/300 ody Material Give body material code as follows: I = uctile Iron Trim ombination isc Material Give disc material code as follows: I = uctile Iron Shaft Material Give shaft material code as follows: S11 = 303 Stainless Steel (2-66", LS or L; 24-" LS or L; 8-" M) S5 = 17-4P Stainless Steel (2-20" O, LS or L; -66" M, LS or L) ody Seat Material Give body seat material code as follows: or NR, PM or KM isc Seat L = luminum ronze (1 only) S2 = 316 Stainless Steel (1 only) or L or S2 isc Seat LN = luminum ronze with NR Seal S2N = 316 Stainless Steel with NR Seal LP = luminum ronze with PM Seal LK = luminum ronze with KM Seal S2P = 316 Stainless Steel with PM Seal S2K = 316 Stainless Steel with KM Seal isc Seat Material Give disc seat material code as follows: NR = crylonitrile-utadiene PM = Terpolymer of thylene Propylene & iene KM = luoro Rubber L = luminum ronze S2 = 316 Stainless Steel Options Give options code as follows: TR = ezurik Standard ertified Production ydrostatic Shell & Seat Test Report P = ertical low Up Position Installation (Not required with LS losure ontrol evice) S16 = 316 Stainless Steel olting losure ontrol evices Give closure control device code as follows: = ir ushion Side Mounted ylinder (Lever & eight) M = Oil ontrolled ottom Mounted uffer (8-66") O = Oil ontrolled Side Mounted ylinder LS = Lever & Spring L = Lever & eight LS = onvertible - Lever & Spring L = onvertible- Lever & eight ccessories Give accessory code as follows: SL22 = (1) Limit Switch - PT 802T-TP SL30 = (1) Proximity Switch - SPT GO 73-13526-2 SL = (1) Proximity Switch - PT GO 7G-23523-2 Ordering xample: S,8,00,1,I,I-S5-L-NR*L,SL22 8
9 imensions Lever and eight (L) Size 1 & 2 1 2 X G G 2" 50mm 3.50 89 13. 3 6. 159 0.63 16 0.88 22 2.5" 65mm 5. 133 5.75 146 0.69 18 3" 80mm 4.13 105 5.50 140 5.13 130 0.75 19 8. 210 4" 100mm 2 0.94 24 1. 6" 150mm 1 4 8.38 213 11.63 5 1 279 12.50 318 1 495 10. 16.75 4 13.00 330 9. 235 1.63 41 10" 0mm 12.63 1 1 1.19 30 1 2 1 22.00 559 1 11. 286 1 3 1. 2.00 51 3 787 19.63 499 15.75 400 2 1.38 35 23.00 584 16" 400mm 3 19.75 502 2.50 6 2. 57 1 450mm 20. 514.00 7 1 2 1.56 40 2 20" 500mm 2 21.50 6.00 1 2 1.69 43 30.50 775 2.50 64 24" 0mm 4 1219 30.00 762 33.50 851 2 1.00 3 30" 750mm 5 1422 3 965 27.75 5 3 978 15.50 394 38.75 984 3.00 76 36" 900mm 63.00 10 40.38 6.13 816 41.50 10 2 686 4 50.00 0 3.38 86 42" 1100mm.00 1778 50.63 1286 3 4 1245 33.00 838 4 1041 2 53.00 1346 2.63 67 5 14 3.69 94 " 1 7 1981 50.63 1286 4 1041.00 4 3 965 4 1207. 743 5 1511 6 1 " 1400mm 8 2210 6 1578 52.00 11 6 1 50.50 1283 3 1003 66. 1683 3.00 76 ontact ezurik " 1500mm 9 2464 72.00 18 5 1473.00 1778 4 45.50 1156 35.50 902 73.00 18 3.13 80 66" 10mm 10 2743 66.63 1692 6 1626 7 1930 50.50 1283 33.50 851 80.00 2 3.44 87 Note: 36" (900mm) & larger have two lever arms, one on each side. Inches Millimeters X P - RTIL UP LR RM SING STNR P, STNR P, LT N LT N STNR P, STNR P, L LT N
10 imensions Lever and Spring (LS) Size 1 & 2 1 2 G G 2" 50mm 3.50 89 13. 3 0.63 16 0.88 22 2.5" 65mm 10.50 267 5. 133 0.69 18 3" 80mm 4.13 105 5.50 140 0.75 19 8. 210 4" 100mm 5.38 1 2 0.94 24 1. 6" 150mm 1 4 8.38 213 1 279 12.50 318 1 495 10. 16.75 4 1.63 41 10" 0mm 12.63 1 10.50 267 1 1.19 30 1 2 1 22.00 559 1 3 1. 2.00 51 3 787 19.63 499 15.75 400 2 10. 1.38 35 23.00 584 16" 400mm 3 19.75 502 2 13.00 330.50 6 2. 57 1 450mm 20. 514.00 7 1 2 1.56 40 2 20" 500mm 2 21.50 6.00 1 2 1.69 43 30.50 775 2.50 64 24" 0mm 4 1219 30.00 762 33.50 851 7.38 187.00 3 30" 750mm 5 1422 3 965 27.75 5 3 978 _ 38.75 984 3.00 76 36" 900mm 63.00 10 40.38 6.13 816 41.50 10 7. 184 2 686 4 50.00 0 3.38 86 42" 1100mm.00 1778 50.63 1286 3 4 1245 33.00 838 53.00 1346 2.63 67 5 14 3.69 94 Inches Millimeters LOSUR ONTROL MOUNTING POSITIONS LT N STNR POSITION LOSUR ONTROL MOUNTING POSITIONS (SON ON TIS RING)
11 imensions & ir ushioned Side Mounted ylinder () Size 1 & 2 1 2 X G G 2" 50mm 3.50 89 13. 3 2 6. 159 0.63 16 0.88 22 2.5" 65mm 10. 5. 133 5.75 146 0.69 18 3" 80mm 4.13 105 10.13 7 5.50 140 5.13 130 0.75 19 8. 210 4" 100mm 9.13 2 2 0.94 24 1. 6" 150mm 1 4 10.38 264 8.38 213 1 419 11.63 5 1 279 12.50 318 1 495 10. 16.75 4 9. 235 1 13.00 330 9. 235 1.63 41 10" 0mm 12.63 1 8.63 219 1 1.19 30 1 2 1 22.00 559 8.88 226 2 1 11. 286 1 3 1. 2.00 51 3 787 19.63 499 15.75 400 2 1 279.00 7 1.38 35 23.00 584 16" 400mm 3 19.75 502 2 9.75 2 30.75 781.50 6 2. 57 1 450mm 20. 514.00 7 8. 210 1 3 889 2 1.56 40 2 20" 500mm 2 21.50 6.00 8.88 226 1 3 2 1.69 43 30.50 775 2.50 64 24" 0mm 4 1219 30.00 762 33.50 851 43.75 1111 2 1.00 3 30" 750mm 5 1422 3 965 27.75 5 3 978 9.75 2 4 1219 15.50 394 38.75 984 3.00 76 36" 900mm 63.00 10 40.38 6.13 816 41.50 10 2 686 5 15 4 50.00 0 3.38 86 42" 1100mm.00 1778 50.63 1286 3 4 1245 33.00 838 6 1 4 1041 2 53.00 1346 2.63 67 5 14 3.69 94 " 1 7 1981 50.63 1286 4 1041.00 4 3 965 7 1905 4 1207. 743 5 1511 6 1 " 1400mm 8 2210 6 1578 52.00 11 6 1 1 8 2134 50.50 1283 3 1003 66. 1683 3.00 76 ontact ezurik " 1500mm 9 2464 72.00 18 5 1473.00 1778 2 686 4 8 22 45.50 1156 35.50 902 73.00 18 3.13 80 66" 10mm 10 2743 66.63 1692 6 1626 7 1930 3 991 50.50 1283 9 2311 33.50 851 80.00 2 3.44 87 Inches Millimeters X P - RTIL UP LR RM SING P - R LR STNR LT N P, STNR P, LT N STNR LT N P, STNR
imensions Oil ontrolled Side Mounted ylinder Size 1 K X G 2" 50mm 3.50 89 13. 3 2 6. 159 0.63 16 2.5" 65mm 10. 5. 133 5.75 146 0.69 18 3" 80mm 4.13 105 10.13 7 5.50 140 8.13 207 5.13 130 0.75 19 4" 100mm 9.13 2 8.94 227 2 0.94 24 6" 150mm 1 4 8.38 213 22.50 572 1 419 11.63 5 1 279 1 495 10. 16.75 4 12.50 318 1 13.00 330 9. 235 10" 0mm 12.63 1 8.63 219 2 1 1.19 30 2 1 22.00 559 8.88 226 2 749 2 1 11. 286 1 3 1. 3 787 19.63 499 15.75 400 2 1 279 33.00 838.00 7 1.38 35 16" 400mm 3 19.75 502 2 9.75 2 35.50 902 30.75 781 1 450mm 20. 514.00 7 8. 210 1 3 953 3 889 2 1.56 40 20" 500mm 2 21.50 6.00 8.88 226 1 3 991 3 2 1.69 43 Size 2 K X G 2" 50mm 3.50 89 13. 3 2 6. 159 0.88 22 2.5" 65mm 10. 5. 133 5.75 146 3" 80mm 4.13 105 10.13 7 5.50 140 8.13 207 5.13 130 8. 210 4" 100mm 9.13 2 8.94 227 1. 6" 150mm 1 4 8.38 213 22.50 572 1 419 11.63 5 12.50 318 1 495 10. 16.75 4 12.50 318 1 13.00 330 9. 235 1.63 41 10" 0mm 14.13 359 2 1 2 1 15.50 394 22.00 559 2 749 2 1 11. 286 2.00 51 3 787 19.63 499 17. 438 2 33.00 838.00 7 23.00 584 16" 400mm 3 21. 0 2 15.50 394 35.50 902 30.75 781.50 6 2. 57 1 450mm 21.75 552.00 7 16.75 4 1 4 1118 3 889 2 20" 500mm 2 23.00 584.00 19. 9 1 4 3 30.50 775 2.50 64 Inches Millimeters Inches Millimeters 12
imensions Oil ontrolled Side Mounted ylinder ll Sizes øg X P - RTIL X UP LR P - RTIL RM SING UP LR RM SING Size 2- (50-) K X P - RTIL UP LR RM SING K L L Size 10-20" (0-500mm) K 13
14 imensions & Oil ontrolled ottom Mounted uffer (M) Size 1 & 2 1 2 X G G 1 495 11.75 8 2 2 13.00 330 9. 235 11.75 8 1.63 41 13.00 330 10" 0mm 14.13 359 30.00 762 33.50 851 1.19 30 1 1 15. 387 2 1 15.50 394 31.50 800 42.00 1067 1 11. 286 1. 1 3 1 4 2.00 51 17.75 451 3 787 19.63 499 17. 438 4 4 1219 1.38 35 18.75 476 23.00 584 20. 514 16" 400mm 3 21. 0 4 50.00 0 21. 0 2. 57.50 6 22.50 572 1 450mm 21.75 552 5 1473 5 1422 1.56 40 2 2 578 2 24.75 6 20" 500mm 2 23.00 584 6 1626.00 4 1.69 43 2 2 2.50 64 30.50 775 2 686 24" 0mm 4 1219 30.00 762 2 6 12 6 1 2 1.00 2 749 3.00 30" 750mm 5 1422 3 965. 743 7 1956 7 1930 15.50 394 38.75 984 3 3.00 76 39. 997 36" 900mm 63.00 10 40.38 6 33.79 858 83.00 2108 8 2184 4 4 1086 3.38 86 50.00 0 4 42" 1100mm.00 1778 50.63 1286.91 963 9 29 9 3 4 1041 2 2.63 67 53.00 1346 4 17 3.69 94 5 14 5 1340 " 1 7 1981 50.63 1286 42.16 1071 1 1 10 2743 4 1207. 743 5 1511 5 1422 6 1.75 13 " 1400mm 8 2210 6 1578 53.16 1350 130.00 3302 1 30 50.50 1283 3 1003 3.00 76 66. 1683 6 1594 ontact ezurik " 1500mm 9 2464 72.00 18 59. 1505 1 3556 130.00 3302 45.50 1156 35.50 902 3.13 80 73.00 18 69. 1759 66" 10mm 10 2743 66.63 1692 65.16 5.00 3861 1 3556 33.50 851 3.44 87 80.00 2 7 1930 Inches Millimeters P - RTIL UP LR RM SING X
imensions onvertible - Lever and eight (L) onvertible - Lever and Spring (LS) 1 & 2 1 2 Size X G G 2" 50mm 3.50 89 13. 3 2 6. 159 0.63 16 0.88 22 2.5" 65mm 10.50 267 5. 133 5.75 146 0.69 18 3" 80mm 4.13 105 5.50 140 5.13 130 0.75 19 8. 210 4" 100mm 5.38 1 2 0.94 24 1. 6" 150mm 1 4 8.38 213 1 419 11.63 5 1 279 12.50 318 1 495 10. 16.75 4 1 13.00 330 9. 235 1.63 41 10" 12.63 10.50 1 1.19 1 0mm 1 267 30 2 1 22.00 559 2 1 11. 286 1 3 1. 2.00 51 3 787 19.63 499 15.75 400 2 10..00 7 1.38 35 23.00 584 16" 3 19.75 2 13.00 30.75.50 2. 400mm 502 330 781 6 57 1 20..00 1 3 2 1.56 2 450mm 514 7 889 40 20" 2 21.50.00 1 3 2 1.69 30.50 2.50 500mm 6 43 775 64 24" SIZS 10" 4 30.00 33.50 7.38 43.75 2 1.00 3 0mm N LRGR 1219 762 851 187 1111 30" 5 3 27.75 3 4 15.50 38.75 3.00 750mm 1422 965 5 978 1219 394 984 76 36" 900mm 63.00 10 40.38 6.13 816 41.50 10 7. 184 2 686 5 15 4 50.00 0 3.38 86 42" 1100mm.00 1778 50.63 1286 3 4 1245 33.00 838 6 1 4 1041 2 53.00 1346 2.63 67 5 14 3.69 94 " 7 50.63 4.00 3 7 4. 5 6 1 1981 1286 1041 4 965 1905 1207 743 1511 1 " 8 6 52.00 6 8 50.50 3 66. 3.00 1400mm 2210 1578 11 1 2134 1283 1003 1683 76 " 9 72.00 5.00 4 8 45.50 35.50 73.00 3.13 ontact ezurik 1500mm 2464 18 1473 1778 22 1156 902 18 80 66" 10 66.63 6 7 50.50 9 33.50 80.00 3.44 10mm 2743 1692 1626 1930 1283 2311 851 2 87 Inches Millimeters LR N IGT SIZS 10" N LRGR LR N SPRING X P - RTIL UP LR RM SING LOSUR ONTROL MOUNTING POSITIONS X P - RTIL UP LR RM SING STNR POSITION (SON ON TIS RING) LT N SIZS 10" N LRGR STNR LT N P, STNR P, LT N LOSUR ONTROL MOUNTING POSITIONS STNR LT N P, STNR P, LT N STNR POSITION LT N (SON ON TIS RING) 15
Sales and Service or information about our worldwide locations, approvals, certifications and local representative: eb Site: www.dezurik.com -Mail: info@dezurik.com 0 Riverside ve. N. Sartell, Minnesota 567 Phone: 0-9-2000 ax: 0-9-2227 ezurik, Inc. reserves the right to incorporate our latest design and material changes without notice or obligation. esign features, materials of construction and dimensional data, as described in this bulletin, are provided for your information only and should not be relied upon unless confirmed in writing by ezurik, Inc. ertified drawings are available upon request. Printed in the U.S..