Hose pumps SP 04 integrated pump exterior pump laboratory pump Otto Huber GmbH Heubergstraße 2 D-78583 Böttingen Phone: Fax: E-Mail: Internet: +49(0)7429/9312-0 +49(0)7429/9312-50 info@otto-huber.de www.otto-huber.de ISO 9001:2000 Certificate-No.: 239876QM Issue 03-2006 page 1-1 Subject to change without prior notification
Hose pumps SP 04 Range of application: Hose pump SP 04 is suitable for delivering fluid and gaseous media, either for simple conveyance or precise proportioning. The use of different hose materials allows for the delivery of different chemicals, abrasive materials, corrosive or sterile media. Hose pump SP 04 is used in laboratories, in analytical and medical systems, in biotechnology, in the food industry, as well as other industrial areas. Three models are available: integrated pump exterior pump laboratory pump Mode of operation: Hose pump SP 04 belongs to the group of positive displacement pumps. The pump operates without valves or seals. The transported media is forced through a hose, which can be quickly exchanged and is therefore very economical. While transporting the medium, the hose is being pinched together by two spring-loaded compression rollers. Thus, the rotating movement of the rollers pushes the medium from the suction side to the discharge side of the hose. Beyond the point, where the hose is being pinched together, the hose expands and creates a vacuum, causing the medium to be drawn forward. The flow rate depends on the RPM of the pump s rotor (roller supports), the inner diameter of the hose, the elasticity of the hose, the back pressure, as well as the viscosity of the transported medium. The inner diameter of the hose, its wall thickness, and the elasticity of the hose determine the extent of the vacuum. The pressure depends on the elasticity of the hose and the contact pressure of the compression rollers. The pump motor is equipped with two compression rollers and four guide rolls. The compression rollers are located opposite to each other, thereby sealing the hose, regardless of the pump rotor s orientation. The guide rolls ensure the hose will remain in a track, which is favourable for the compression rollers. Changing the hose is very easy and does not require any tools. First, the knurled nut is loosened and together with the screw tilted toward the top. Then the pump housing is pulled down and away. Both the hose adapter and the hose itself can now be pulled out and to the side of the guides. The replacement hose can be installed in exactly the reverse order. page 1-2
Hose pumps SP 04 Contents Range of application, operation SP 04 1-2 Contents 1-3 General specifications 1-4 Integrated pump SP 04 E, 0.1 L/h to 1 L/h 2-1, 2-2 Integrated pump SP 04 E, 2 L/h to 20 L/h 3-1, 3-2 Integrated pump SP 04 E, 30 L/h to 60 L/h 4-1, 4-2 Integrated pump SP 04 EG, 0.1 L/h to 2 L/h 5-1, 5-2 Integrated pump SP 04 EG, 4 L/h to 40 L/h 6-1, 6-2 Exterior pump SP 04 G, 0.1 L/h to 6 L/h 7-1, 7-2 Laboratory pump SP 04 L, 0.1 L/h to 60 L/h 9-1, 9-2 Accessory: Hose adapter 10-1 Accessory: Hose clamp spring, roller support 10-2 Accessory: Pump housing, base plate 10-3 Accessory: Pump hoses 10-4 Accessory: Pump heads 10-5 page 1-3
Hose pumps SP 04 General information Integrated pumps SP04 E, SP 04 EG Integrated pumps are suitable for the installation inside a housing, whereby the pump head is mounted outside of the enclosure and the motor complete with gear is mounted inside. A shaft connects the pump head with the gear and the pump head is attached, using two knurled nuts. The pump head can be removed by loosening both knurled nuts. Using the two threaded studs, the motor and gear can now be attached to the wall of the housing. The pump head can be reattached to the outside and fastened, using both knurled nuts. The wall thickness of either the housing or the front plate should not exceed 6 mm. An angled plate with two through holes 4.2 mm, at 70 mm spacing, serves as an alternate attachment method. The hose pump can be mounted with two M 4 screws. Exterior pumps SP 04 G, SP 04 GR Hose pumps SP 04 G and SP 04 GR are similar in design to the integrated device. A cover protects both motor and gear, and a fine-wire fuse is built into the front plate. A cable connects the pump to the power supply. This model is mainly mounted to the outside walls of housings, equipment or machines. An angled plate with two through holes 4.2 mm, at 70 mm spacing, is used to attach the pump. The hose pump can be mounted with two M 4 screws. Laboratory pumps SP 04 L The design of the hose pump SP 04 L is similar to that of the integrated model. A precision direct current motor activates the pump. The flow capacity is infinetely variable and the motor s rotational direction is reversible. A power cable is supplied. General information All models are supplied ready-to-operate. Standard type adaptors are used as hose connections. Should you require a special design, please indicate so with your order. When ordering a special design, complete replacement hose sets and replacement pump heads, a product code number will be supplied with the order confirmation or with the delivery of the item. This ensures future orders of the device or spare part can be expedited effortless. Upon request, the integrated models SP 04 E and SP 04 EG can also be delivered with a blue-coloured pump head. Different flow capacities and voltages are also available. page 1-4
Hose pumps SP 04 E Pump type SP 04 E/01 SP 04 E/02 SP 04 E/03 SP 04 E/05 SP 04 E/1 Intake capacity 0.1 L/h 0.2 L/h 0.3 L/h 0.5 L/h 1.0 L/h Power input 65 ma 75 ma Voltage 230 V Frequency 50 Hz Operating mode DB Protection type IP 00 Connection Plug 6.3x0.8 Dimension a 55 mm 65 mm Pump hose see table page 2-2 Hose adapter see accessories page 10-1 Vacuum -680 mbar Pressure 500 mbar Weight 540 g 690 g page 2-1
Hose pumps SP 04 E Hose material Hose dimensions Intake capacity in litres per hour (L/h) ±10% 1 Order No. of hose pump SP04E/01 SP04E/02 SP04E/03 SP04E/05 SP04E/1 5.0x1.5 Silicone 4.0x1.5 3.0x1.5 0.1 0.2 0.3 61-001-100-01 61-002-100-01 61-003-100-01 0.5 1.0 61-005-100-01 61-010-100-01 A-60-G 0.1 0.2 0.3 61-001-100-02 61-002-100-02 61-003-100-02 0.5 1.0 61-005-100-02 61-010-100-02 A-60-F 0.1 0.2 0.3 61-001-100-03 61-002-100-03 61-003-100-03 R-3603 0.1 0.2 0.3 61-001-100-04 61-002-100-04 61-003-100-04 0.5 1.0 61-005-100-04 61-010-100-04 R-1000 Viton 2 0.1 0.2 0.3 61-001-100-05 61-002-100-05 61-003-100-05 1: Capacities shown here were determined using water without back pressure, running clockwise and at ambient temperature. Values are influenced by dimensional tolerances and hardness of the hose, as well as temperature and the viscosity of the delivered medium. 2: When using Viton-hoses, a special roller support with reinforced springs is being used. 3: As a standard, hose pumps are supplied with hose adaptors (see page 10-1). page 2-2
Hose pumps SP 04 E Pump type SP 04 E/2 SP 04 E/4 SP 04 E/6 SP 04 E/12 SP 04 E/20 Intake capacity 2 L/h 4 L/h 6 L/h 12 L/h 20 L/h Power input 150 ma 240 ma Voltage 230 V Frequency 50 Hz Operating mode DB Protection type IP 00 Connection Plug 6,3x0,8 Dimension a 65 mm 75 mm Pump hose see table page 3-2 Hose adapter see accessories page 10-1 Vacuum -680 mbar Pressure 500 mbar Weight 780 g 1080 g page 3-1
Hose pumps SP 04 E Hose material Silicone Hose dimensions 5,0x1,5 4,8x1,6 4,0x1,5 3,0x1,5 Intake capacity in litres per hour (L/h) ±10% 1 Order No. of hose pump 3 SP04E/2 SP04E/4 SP04E/6 SP04E/12 SP04E/20 12 20 61-120-100-01 61-200-100-01 2 4 6 61-020-100-01 61-040-100-01 61-060-100-01 A-60-G 4,8x1,6 4,0x1,6 3,2x1,6 2 4 6 61-020-100-02 61-040-100-02 61-060-100-02 12 20 61-120-100-02 61-200-100-02 A-60-F 4,8x1,6 3,2x1,6 12 20 61-120-100-03 61-200-100-03 R-3603 4,8x1,6 4,0x1,6 2 4 6 61-020-100-04 61-040-100-04 61-060-100-04 12 20 61-120-100-04 61-200-100-04 3,2x1,6 R-1000 4,8x1,6 12 20 61-120-100-05 61-200-100-05 Viton 2 4,8x1,6 3,2x1,6 12 20 61-120-100-06 61-200-100-06 1: Capacities shown here were determined using water without back pressure, running clockwise and at ambient temperature. Values are influenced by dimensional tolerances and hardness of the hose, as well as temperature and the viscosity of the delivered medium. 2: When using Viton-hoses, a special roller support with reinforced springs is being used. 3: As a standard, hose pumps are supplied with hose adaptors (see page 10-1). page 3-2
Hose pumps SP 04 E Pump type SP 04 E/30 SP 04 E/40 SP 04 E/60 Intake capacity 30 L/h 40 L/h 60 L/h Power input 600 ma Voltage 230 V Frequency 50 Hz Operating mode DB Protection type IP 00 Connection Plug 6.3x0.8 Pump hose see table page 4-2 Hose adapter see accessories page 10-1 Vacuum -680 mbar Pressure 500 mbar Weight 1400 g page 4-1
Hose pumps SP 04 E Hose material Silicone Hose dimensions 5.0x1.5 4.0x1.5 Intake capacity in litres per hour (L/h) ±10% 1 Order No. of hose pump 3 SP04E/30 SP04E/40 SP04E/60 30 40 60 61-300-100-01 61-400-100-01 61-600-100-01 A-60-G A-60-F R-3603 R-1000 3.0x1.5 30 40 60 61-300-100-02 61-400-100-02 61-600-100-02 30 40 60 61-300-100-03 61-400-100-03 61-600-100-03 30 40 60 61-300-100-04 61-400-100-04 61-600-100-04 30 40 60 61-300-100-04 61-400-100-05 61-600-100-05 Viton 2 1: Capacities shown here were determined using water without back pressure, running clockwise and at ambient temperature. Values are influenced by dimensional tolerances and hardness of the hose, as well as temperature and the viscosity of the delivered medium. 2: When using Viton-hoses, a special roller support with reinforced springs is being used. 3: As a standard, hose pumps are supplied with hose adaptors (see page 10-1). page 4-2
Hose pumps SP 04 EG Pump type SP 04 EG/01 SP 04 EG/02 SP 04 EG/03 SP 04 EG/05 SP 04 EG/1 SP 04 EG/2 Intake capacity 0.1 L/h 0.2 L/h 0.3 L/h 0.5 L/h 1.0 L/h 2.0 L/h Power input 90 ma Voltage 24 V DC Operating mode DB Protection type IP 00 Connection Plug 2.8x0.5 Pump hose see table page 5-2 Hose adapter see accessories page 10-1 Vacuum -680 mbar Pressure 500 mbar Weight 460 g page 5-1
Hose pumps SP 04 EG Hose material Hose dimensions Intake capacity in litres per hour (L/h) ±10% 1 Order No. of hose pump SP04EG/01 SP04EG/02 SP04EG/03 SP04EG/05 SP04EG/1 SP04EG/2 5.0x1.5 Silicone 4.0x1.5 3.0x1.5 0.1 L/h 0.2 L/h 0.3 L/h 62-001-100-01 62-002-100-01 62-003-100-01 0.5 L/h 1 L/h 2 L/h 62-005-100-01 62-010-100-01 62-020-100-01 A-60-G 0.1 L/h 0.2 L/h 0.3 L/h 62-001-100-02 62-002-100-02 62-003-100-02 0.5 L/h 1 L/h 2 L/h 62-005-100-02 62-010-100-02 62-020-100-02 A-60-F 0.1 L/h 0.2 L/h 0.3 L/h 62-001-100-03 62-002-100-03 62-003-100-03 R-3603 0.1 L/h 0.2 L/h 0.3 L/h 62-001-100-04 62-002-100-04 62-003-100-04 0.5 L/h 1 L/h 2 L/h 62-005-100-04 62-010-100-04 62-020-100-04 R-1000 Viton 2 1: Capacities shown here were determined using water without back pressure, running clockwise and at ambient temperature. Values are influenced by dimensional tolerances and hardness of the hose, as well as temperature and the viscosity of the delivered medium. 2: When using Viton-hoses, a special roller support with reinforced springs is being used. 3: As a standard, hose pumps are supplied with hose adaptors (see page 10-1). page 5-2
Hose pumps SP 04 EG Pump type SP 04 EG/4 SP 04 EG/6 SP 04 EG/12 SP 04 EG/20 SP 04 EG/30 SP 04 EG/40 Intake capacity 4 L/h 6 L/h 12 L/h 20 L/h 30 L/h 40 L/h Power input 450 ma Voltage 24 V DC Operating mode DB Protection type IP 00 Connection Plug 2.8x0.5 Pump hose see table page 6-2 Hose adapter see accessories page 10-1 Vacuum -680 mbar Pressure 500 mbar Weight 560 g page 6-1
Hose pumps SP 04 EG Hose material Hose dimensions Intake capacity in litres per hour (L/h) ±10% 1 Order No. of hose pump SP04EG/4 SP04EG/6 SP04EG/12 SP04EG/20 SP04EG/30 SP04EG/40 5.0x1.5 Silicone 4.0x1.5 4 L/h 6 L/h 12 L/h 62-040-100-01 62-060-100-01 62-120-100-01 20 L/h 30 L/h 40 L/h 62-200-100-01 62-300-100-01 62-400-100-01 3.0x1.5 A-60-G 4 L/h 6 L/h 12 L/h 62-040-100-02 62-060-100-02 62-120-100-02 20 L/h 30 L/h 40 L/h 62-200-100-02 62-300-100-02 62-400-100-02 A-60-F 20 L/h 30 L/h 40 L/h 62-200-100-03 62-300-100-03 62-400-100-03 20 L/h 30 L/h 40 L/h 62-200-100-04 62-300-100-04 62-400-100-41 R-3603 R-1000 20 L/h 30 L/h 40 L/h 62-200-100-05 62-300-100-05 62-400-100-05 Viton 2 1: Capacities shown here were determined using water without back pressure, running clockwise and at ambient temperature. Values are influenced by dimensional tolerances and hardness of the hose, as well as temperature and the viscosity of the delivered medium. 2: When using Viton-hoses, a special roller support with reinforced springs is being used. 3: As a standard, hose pumps are supplied with hose adaptors (see page 10-1). page 6-2
Hose pumps SP 04 G Pump type SP 04 G/01 SP 04 G/02 SP 04 G/03 SP 04 G/05 SP 04 G/1 SP 04 G/2 SP 04 G/4 SP 04 G/6 Intake capacity 0.1 L/h 0.2 L/h 0.3 L/h 0.5 L/h 1 L/h 2 L/h 4 L/h 6 L/h Power input 55 ma 65 ma 150 ma Voltage 230 V Frequency 50 Hz Operating DB d Protection type IP 41 Connection Connecting cable Pump hose see table page 7-2 Hose adapter see accessories page 10-1 Vacuum -680 mbar Pressure 500 mbar Weight 860 g 1010 g 1100 g page 7-1
Hose pumps SP 04 G Hose material Hose dimensions Intake capacity in litres per hour (L/h) ±10% 1 Order No. of hose pump 3 SP 04 G/01 SP 04 G/02 SP 04 G/03 SP 04 G/05 SP 04 G/01 SP 04 G/01 SP 04 G/4 SP 04 G/6 5.0x1.5 Silicone 4.0x1.5 3.0x1.5 0.1 L/h 0.2 L/h 0.3 L/h 0.5 L/h 63-001-100-01 63-002-100-01 63-003-100-01 63-005-100-01 1 L/h 2 L/h 4 L/h 6 L/h 63-010-100-01 63-020-100-01 63-040-100-01 63-060-100-01 A-60-G 0.1 L/h 0.2 L/h 0.3 L/h 0.5 L/h 63-001-100-02 63-002-100-02 63-003-100-02 63-005-100-02 1 L/h 2 L/h 4 L/h 6 L/h 63-010-100-02 63-020-100-02 63-040-100-02 63-060-100-02 A-60-F 0.1 L/h 0.2 L/h 0.3 L/h 0.5 L/h 63-001-100-03 63-002-100-03 63-003-100-03 63-005-100-03 R-3603 0.1 L/h 0.2 L/h 0.3 L/h 0.5 L/h 63-001-100-04 63-002-100-04 63-003-100-04 63-005-100-04 R-1000 Viton 2 1: Capacities shown here were determined using water without back pressure, running clockwise and at ambient temperature. Values are influenced by dimensional tolerances and hardness of the hose, as well as temperature and the viscosity of the delivered medium. 2: When using Viton-hoses, a special roller support with reinforced springs is being used. 3: As a standard, hose pumps are supplied with hose adaptors (see page 10-1). page 7-2
Hose pumps SP 04 L Pump type SP04L/01 SP04L/02 SP04L/1 SP04L/2 SP04L/4 SP04L/6 SP04L/20 SP04L/40 SP04L/60 Intake capacity max. 0.147 L/h max. 0.28 L/h max. 1.31 L/h max. 2.47 L/h max. 5.1 L/h max. 7.2 L/h max. 25 L/h max. 46 L/h max. 67 L/h RPM, without hose 0.15-0.23-1.5 min -1 2.9 min -1 1.3-2.1-6 - 7.5-43 - 148-250 - 13.4 min -1 25 min -1 52 min -1 74.5 min -1 272 min -1 513 min -1 780 min -1 Power consumption max 10 W max. 30 W Voltage 100-240 V Frequency 50-60 Hz Operating mode DB Protection type IP 41 Connection Power supply plug with cable approx. 1.4 m long Pump hose see table page 9-2 Hose adopter see accessories page 10-1 Vacum -680 mbar Pressure 500 mbar Weight approx. 530 g page 9-1
Hose pumps SP 04 L Schlauchwerkstoff Silicone A-60-G A-60-F R-3603 R-1000 Schlauchabmessung 5.0x1.5 4.0x1.5 3.0x1.5 Intake capacity in litres per hour (L/h) ±10% 1 Order No. of hose pump 3 SP04L/01 SP04L/02 SP04L/1 SP04L/2 SP04L/4 SP04L/6 SP04L/20 SP04L/40 SP04L/60 0.015-0.147 0.024-0.28 0.135-1.3 0.18-2.47 0.57-5.1 0.7-7.2 3.3-25 9.5-46 16-67 64-001-20-02 64-002-20-02 64-010-20-02 64-020-20-02 64-040-20-02 64-060-20-02 64-200-20-02 64-400-20-02 64-600-20-02 0.015-0.147 0.024-0.28 0.135-1.3 0.18-2.47 0.57-5.1 0.7-7.2 3.3-25 9.5-46 15-65 64-001-20-01 64-002-20-01 64-010-20-01 64-020-20-01 64-040-20-01 64-060-20-01 64-200-20-01 64-400-20-01 64-600-20-01 0.011-0.11 0.017-0.21 0.1-0.96 0.14-1.81 0.42-3.7 0.5-5.3 2.4-19 7.5-33 12-48 64-001-20-03 64-002-20-03 64-010-20-03 64-020-20-03 64-040-20-03 64-060-20-03 64-200-20-03 64-400-20-03 64-600-20-03 0.0065-0.062 0.01-0.12 0.056-0.55 0.077-1 0.24-2.1 0.3-3 1.4-11 4.5-19 7-28 64-001-20-04 64-002-20-04 64-010-20-04 64-020-20-04 64-040-20-04 64-060-20-04 64-200-20-04 64-400-20-04 64-600-20-04 0.013-0.12 0.019-0.23 0.11-1.07 0.16-2 0.45-4.1 0.55-5.9 2.4-20 6.5-36 10-53 64-001-20-05 64-002-20-05 64-010-20-05 64-020-20-05 64-040-20-05 64-060-20-05 64-200-20-05 64-400-20-05 64-600-20-05 0.011-0.1 0.017-0.2 0.094-0.91 0.14-1.73 0.38-3.6 0.48-5 2-18 5.7-30 8-45 64-001-20-06 64-002-20-06 64-010-20-06 64-020-20-06 64-040-20-06 64-060-20-06 64-200-20-06 64-400-20-06 64-600-20-06 0.007-0.066 0.01-0.127 0.059-0.58 0.088-1.1 0.25-2.2 0.3-3.2 1.4-11 4-19 6-29 64-001-20-07 64-002-20-07 64-010-20-07 64-020-20-07 64-040-20-07 64-060-20-07 64-200-20-07 64-400-20-07 64-600-20-07 0.013-0.127 0.019-0.25 0.11-1.12 0.16-2.1 0.43-4.3 0.58-6.2 2.6-21 7.5-38 11-57 64-001-20-08 64-002-20-08 64-010-20-08 64-020-20-08 64-040-20-08 64-060-20-08 64-200-20-08 64-400-20-08 64-600-20-08 0.0065-0.065 0.01-0.125 0.056-0.57 0.082-1.1 0.22-2.18 0.3-3.1 1.4-11 4-19 6-29 64-001-20-09 64-002-20-09 64-010-20-09 64-020-20-09 64-040-20-09 64-060-20-09 64-200-20-09 64-400-20-09 64-600-20-09 0.014-0.133 0.02-0.257 0.11-1.17 0.18-2.21 0.47-4.5 0.6-6.3 1.8-21 5-36 7-51 64-001-20-10 64-002-20-10 64-010-20-10 64-020-20-10 64-040-20-10 64-060-20-10 64-200-20-10 64-400-20-10 64-600-20-10 0.0066-0.064 0.01-0.124 0.53-0.56 0.085-1.07 0.23-2.1 0.3-3 1.3-11 3-18 4-26 64-001-20-12 64-002-20-12 64-010-20-12 64-020-20-12 64-040-20-12 64-060-20-12 64-200-20-12 64-400-20-12 64-600-20-12 0.013-0.136 0.02-0.262 0.12-1.2 0.17-2.26 0.47-4.5 0.6-6.6 3.3-25 9-43 16-63 64-001-20-13 64-002-20-13 64-010-20-13 64-020-20-13 64-040-20-13 64-060-20-13 64-200-20-13 64-400-20-13 64-600-20-13 Viton 2 0.014-0.117 0.022-0.226 0.1-1 0.16-1.93 0.32-3.9 0.47-5.5 - - - 64-001-20-14 64-002-20-14 64-010-20-14 64-020-20-14 64-040-20-14 64-060-20-14 - - - 0.0077-0.062 0.012-0.12 0.056-0.54 0.087-1 0.2-2 0.25-2.9 - - - 64-001-20-15 64-002-20-15 64-010-20-15 64-020-20-15 64-040-20-15 64-060-20-15 - - - 1: Capacities shown here were determined using water without back pressure, running clockwise and at ambient temperature. Values are influenced by dimensional tolerances and hardness of the hose. as well as temperature and the viscosity of the delivered medium. 2: When using Viton-hoses, a special roller support with reinforced springs is being used. Vitro hose for SP04L/60. SP04L/40 and SP04L/20 only operational with limited controlability. 3: As a standard. hose pumps are supplied with hose adaptors (see page 10-1). page 9-2
Accessories for hose pumps SP 04 Hose adopter designs Dimensioned parts are outside the pump. For pump hose 5.0x1.5 und For pump hose 4.0x1.5 und For pump hose 3.0x1.5 und Standard design Order No.: 17-01-002 17-01-014 17-01-021 Special designs available upon request (please indicate when ordering) Order No.: 17-01-002-1 17-01-011 Order No.: 17-01-025 17-01-012 Order No.: 17-01-010 Order No.: 17-01-024 Hose adapters are made from polypropylene (natural colour). Unless otherwise indicated, hose pumps are supplied with standard hose adapters. page 10-1
Accessories for hose pumps SP 04 Clamp springs Hose clamp springs are suitable for all pump hose materials. Suitable for the following pump hose dimensions: 5.0 x 1.5; 4.8 x 1.6 Order No.: 24-36-004 Suitable for the following pump hose dimensions: 4.0 x 1.6; 4.0 x 1.5; 3.2 x 1.6; 3.0 x 1.5 Order No.: 24-36-005 Roller support Suitable for the following pump hoses: Pump hose material: Silicone, A-60-G, A-60-F R-3603, R-1000 Pump hose dimensions: 5.0 x 1.5; 4.8 x 1.6; 4.0 x 1.6; 4.0 x 1.5 3.2 x 1.6; 3.0 x 1.5 Order No.: 60-03-004 Roller support (re-inforced) Suitable for the following pump hoses: Pump hose material: Fluran F-5500-A Pump hose dimensions: 4.8 x 1.6; 3.2 x 1.6 Order No.: 60-03-006 page 10-2
Accessories for hose pumps SP 04 Pump housing with window (Suitable for all pump types SP 04) Order No.: 60-02-001 Base plate red-white (standard) Order No.: 60-01-001 Base plate blue-white (special colours available for SP 04 E) Order No.: 60-01-002 page 10-3
Accessories for hose pumps SP 04 Complete set of replacement hoses (Pump hose with adapter and hose clamp spring, ready-to-use) When ordering standard pump hoses, please specify the exact hose pump type and the order number of the hose pump. Example: Replacement pump hose for SP 04 E/6, 61-060-100-01 When ordering non-standard pump hoses, please specify the exact pump hose type and the order number of the hose pump. (The order number of the hose clamp spring is not required) Example: Replacement pump hose, hose A-60-G c/w hose adapter 17-01-025 Replacement pump hoses (by the metre) Pump hose material: Dimension: Order No.: Silicone 5.0 x 1.5 20-23-001 Silicone 4.8 x 1.6 20-23-013 Silicone 4.0 x 1.5 20-23-002 Silicone 3.0 x 1.5 20-23-016 A-60-G 4.8 x 1.6 20-23-007 A-60-G 4.0 x 1.6 20-23-014 A-60-G 3.2 x 1.6 20-23-006 A-60-F 4.8 x 1.6 20-23-019 A-60-F 3.2 x 1.6 20-23-024 R-3603 4.8 x 1.6 20-23-017 R-3603 4.0 x 1.6 20-23-021 R 3603 3.2 x 1.6 20-23-025 R-1000 4.8 x 1.6 20-23-018 Fluran F-5500-A 4.8 x 1.6 20-23-008 Fluran F-5500-A 3.2 x 1.6 20-23-015 page 10-4
Accessories for hose pumps SP 04 Complete set of replacement pump heads Base plate, complete pump hose, and pump housing with window, assembled When ordering standard pump heads, please specify the exact hose pump type and the order number of the hose pump. Example: Replacement pump head for SP 04 E/6, 61-060-100-01 When ordering non-standard pump heads, please indicate type and order number of base plate, the pump hose material and the order number of the hose adaptor. (The order number of the hose clamp spring and the pump housing is not required) Example: Replacement pump head, base plate blue-white, 60-01-002; hose A-60-G c/w hose adaptor 17-01-025 page 10-5