051562 DIAGNOSTICS 05ETR02 DRL RELAY CIRCUIT CIRCUIT DESCRIPTION The multiplex network body ECU controls DRL No.2, No. and No.4 relays. The headlamp (High) is connected in serial when the daytime running light system operates. When Daytime Running Light System is Operated: DRL No.2 Relay To Multiplex Network Body ECU DRL No. Relay Headlamp RH (Hi) DRL No.4 Relay Headlamp LH (Hi) To HEAD Relay I40822 1752
DIAGNOSTICS 05156 The headlamp (High) is connected in parallel when the HI BEAM or FLASH operates. When HI Beam or Flash is Operated: DRL No.2 Relay To Multiplex Network Body ECU DRL No. Relay Headlamp RH (Hi) DRL No.4 Relay Headlamp LH (Hi) To HEAD Relay I4082 175
051564 DIAGNOSTICS WIRING DIAGRAM RB RB RB LW LW LY Engine Room R/B No. DRL No.2 Relay 1 1 5 DRL H Headlamp RH (High Beam) RW RL RW 2 1 DRL No. Relay 4 2 5 2 B B WB Engine Room R/B H4 Headlamp RH (Low Beam) RY H2 Headlamp LH (Low Beam) RW WB WB WB Engine Room R/B No. DRL No.4 Relay H1 Headlamp LH (High Beam) RW R 2 1 5 LR B 4 IK HLP LH LWR HLP RH LWR R 2 2 2 Body ECU B11 HRLY 5 2F HLP RH UPR HLP LH UPR 2 2F WB 4 HEAD LAMP Relay 2G 4 Battery FL MAIN 2 MAIN 1 1 2B 1 2I F7 FL Block W W 1 P J J/C A EB EA EG A 16 IK J1 J/C B 2 B11 DRL E74077 1754
DIAGNOSTICS INSPECTION PROCEDURE 1 PERFORM ACTIVE TEST USING HANDHELD TESTER 051565 Connect the handheld tester to the DLC. (b) Turn the ignition switch to the ON position and turn the handheld tester main switch on. (c) Select the item below in the ACTIVE TEST and then check the relay operation. BODY NO.1 (MULTIPLEX NETWORK BODY ECU): Item Test Details Diagnostic Note HEAD LIGHT Headlamp relay ON/OFF : Headlamp (low) comes on. BODY NO.1 (MULTIPLEX NETWORK BODY ECU): Item Test Details Diagnostic Note DIMMER SIG DRL No.2 relay ON/OFF : Headlamp (high) comes on. NG Go to step 2 PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE (SEE PAGE 05158 ) 2 INSPECT MULTIPLEX NETWORK BODY ECU (b) Disconnect the B11 connector from the multiplex network body ECU. Using a service wire, connect B11 of the wire harness side and body ground. : Headlamp (low) comes on. Multiplex Network Body ECU B11 B11 E7426 NG Go to step 5 1755
051566 DIAGNOSTICS INSPECT MULTIPLEX NETWORK BODY ECU Using a service wire, connect B112 of the wire harness side and body ground. : Headlamp (high) comes on (decrease mode). Multiplex Network Body ECU B11 B112 E7426 NG Go to step 7 1756
DIAGNOSTICS 051567 4 INSPECT MULTIPLEX NETWORK BODY ECU (b) Using a service wire, connect B11 of the wire harness side and body ground. Using a service wire, connect B112 of the wire harness side and body ground. : Headlamp (high) comes on. Multiplex Network Body ECU B11 B11 B112 E7426 NG REPAIR OR REPLACE HARNESS OR CONNECTOR PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE (SEE PAGE 05158 ) 1757
051568 DIAGNOSTICS 5 INSPECT ENGINE ROOM J/B Measure the voltage according to the value(s) in the table below. Standard: Tester connection Condition Specified condition 2G4 Body ground Always 10 to 14 V 2G 2G4 E72985 NG Go to step 6 REPAIR OR REPLACE HARNESS OR CONNECTOR (ENGINE ROOM J/B MULTIPLEX NETWORK BODY ECU) 1758
DIAGNOSTICS 051569 6 CHECK HARNESS AND CONNECTOR(POWER SOURCE CIRCUIT) (b) Disconnect the 2I connector from the engine room J/B. Measure the voltage according to the value(s) in the table below. Standard: Tester connection Condition Specified condition 2I1 Body ground Always 10 to 14 V 2I 2I1 E72985 NG REPAIR OR REPLACE HARNESS OR CONNECTOR REPLACE ENGINE ROOM J/B 1759
051570 DIAGNOSTICS 7 INSPECT ENGINE ROOM J/B (b) Disconnect the 2B connector from the engine room J/B. Using a service wire, connect 2B1 of the engine room J/B side and body ground. : Headlamp (high) comes on (decrease mode). 2B1 2B E72985 NG Go to step 8 REPAIR OR REPLACE HARNESS OR CONNECTOR (ENGINE ROOM J/B MULTIPLEX NETWORK BODY ECU) 1760
DIAGNOSTICS 051571 8 INSPECT ENGINE ROOM J/B Measure the voltage according to the value(s) in the table below. Standard: Tester connection Condition Specified condition 2F2 Body ground Connect 2B1 and body ground 10 to 14 V 2F5 Body ground Connect 2B1 and body ground 10 to 14 V 2F 2F2 2F5 E72985 NG Go to step 9 REPAIR OR REPLACE HARNESS OR CONNECTOR (EACH OF HEADLAMP CIRCUIT) 1761
051572 DIAGNOSTICS 9 INSPECT ENGINE ROOM J/B Measure the voltage according to the value(s) in the table below. Standard: Tester connection Condition Specified condition 2B1 Body ground Always 10 to 14 V 2B1 2B E72985 NG Go to step 10 REPLACE ENGINE ROOM J/B 1762
DIAGNOSTICS 05157 10 CHECK HARNESS AND CONNECTOR(POWER SOURCE CIRCUIT) (b) Disconnect the 2I connector from the engine room J/B. Measure the voltage according to the value(s) in the table below. Standard: Tester connection Condition Specified condition 2I1 Body ground Always 10 to 14 V 2I 2I1 E72985 NG REPAIR OR REPLACE HARNESS OR CONNECTOR REPLACE ENGINE ROOM J/B 176