SONOI VVS no voltage release (tamperproof) manual reset construction 1/4 U 2 1 3 3/2 Series 3 TURS The valves are certified according to I 61508 unctional Safety data and have SI-3 capability (xida approval) ompact Tamperproof/Manual Reset function which means that the valve has to be energized as well as manually operated before it stays in the "latched" position. ecause of the tamperproof feature there will be no flow from port 3 to port 2 if only the push button is pressed. The No Voltage Release (NVR) function will make sure that the valve trips when de-energized PT rider rings and graphite-filled PT seals reduce friction and eliminate sticking The solenoid valves are recommended for pilot applications with basic flow, wide pressure ranges and no minimum operating pressure oils used in metal enclosures have class insulation materials Peak voltage suppression diodes are standard in solenoids with metal enclosures The solenoid valves satisfy all relevant irectives NR ifferential pressure Maximum viscosity Response times 0-10 bar [1 bar = 100kPa] 65 cst (mm 2 /s) 75-100 ms fluids ( ) temperature range (TS) seal materials ( ) air, inert gas, water, oil -20 to +120-40 to + 40 PM (fluoroelastomer) VMQ ((sillicone) MTRIS IN ONTT WIT UI ( ) nsure that the compatibility of the fluids in contact with the materials is verified rass body Stainless steel body ody rass ISI 316 Stem Stainless steel Stainless steel ore tube Stainless steel Stainless steel ore and plugnut Stainless steel Stainless steel Springs Stainless steel Stainless steel Sealings and poppets PM or VMQ PM or VMQ Rider Ring PT PT P 1 3 RP MP 2 P Not vailable 3,6W - 3,7W 5,7W - 5,8W 10,0W-11,2W ow Reduced Medium asic SPIITIONS pipe size orifice size flow coefficient v operating pressure differential (bar) level prefix optional solenoids POWR VS - cold electrical holding values (watt) basic catalogue number max. (PS) NM TX / Ix min. air/water ( ) 7&9 x d x e mb x mb IP65 (mm) (m 3 /h) (l/m) ~/= ~/= N M PV S brass stainless st. U - Universal, PM sealings and poppets, manual reset 1/4 5,7 0,55 9,2 0 10 P 3021 3022 1/4 5,7 0,55 9,2 0 10 MP - - 3221 3222 1/4 5,7 0,55 9,2 0 10 RP - - 3121 3122 U - Universal, VMQ sealings and poppets, manual reset 1/4 5,7 0,55 9,2 0 10 P 3071 3072 1/4 5,7 0,55 9,2 0 10 MP - - 31 32 1/4 5,7 0,55 9,2 0 10 RP - - 3171 3172 U - Universal, PM sealings and poppets, manual reset tamperproof 1/4 5,7 0,55 9,2 0 10 P 3031 3032 1/4 5,7 0,55 9,2 0 10 MP - - 3231 3232 1/4 5,7 0,55 9,2 0 10 RP - - 3131 3132 U - Universal, VMQ sealings and poppets, manual reset tamperproof 1/4 5,7 0,55 9,2 0 10 P 3081 3082 1/4 5,7 0,55 9,2 0 10 MP - - 3281 3282 1/4 5,7 0,55 9,2 0 10 RP - - 3181 3182 Select 8 for NPT NSI 1.20.3 or Select for ISO (228/1) vailable feature vailable feature in only - Not available Pneutrol International td are Platinium istributors for SO Numatics ontact us : 5 aulside rive, ntrim, Northern Ireland, T 2U www.valves-direct.com Sales@pneutrol.com Tel: +44 (0) 28 9448 1800
SRIS 3 PRIX T prefix description level 1 2 3 4 5 6 7 P RP MP P xplosionproof - NM 7, 9 - Zinc plated steel conduit - - - V xplosionproof - NM 7, 9-316 SS conduit - - - M Waterproof IP67 - Metal enclosure (N/I 60079-7+18, 612-1)* - T Threaded conduit/hole (M20 x 1,5) - I S S Intrinsically safe with S coil (N/I 60079-11+26, 612-11)* - - - - N lameproof - luminium (N/I 60079-1, 60079-31)* - P V ncapsulated epoxy moulded (N/I 60079-18, 612-18)* - - - S Solenoid with spade plug connector (N/I 60730) - W P Waterproof IP67 - Metal enclosure - W P I S I.S. with Metal IP67 enclosure (N/I 60079-11+26, 612-11)* - - - - W S Waterproof IP67-316 SS enclosure - W S M Waterproof IP67-316 SS enclosure (N/I 60079-7+18, 612-1)* - W S I S I.S. with 316 SS IP67 enclosure (N/I 60079-11+26, 612-11)* - - - - W S N lameproof - 316 SS (N/I 60079-1, 60079-31)* - T Threaded conduit (1/2" NPT) - lass - attery charging circuit - - - T lass - igh temperature - - - - X Other special constructions - SUIX T suffix description level 1 2 3 4 5 P RP MP P PM (ethylene-propylene) - - - - R (chloroprene) - - - - N Oxygen service (R (chloroprene)) - - - - N V PM (fluoroelastomer) and parts cleaned for oxygen service - O poxy coating on all external surfaces - M Mounting bracket - - - - M O Push type manual operator - M S Screw type manual operator (1) - M Metering device - - - - vailable feature vailable feature in only - Not available * TX solenoids are also approved according to N 13463-1 (non electrical valves) (1) unctional Safety certification is not applicable with this feature PROUT STION UI STP 1 Select basic catalogue number,including pipe thread indentification letter. Refer to the specifications table on page 1. xample: 83021 STP 2 Select prefix (combination). Refer to the specifications table on page 1 and the prefix table on page 2, respect the indicated level. xample: N STP 3 Select suffix (combination) if required. Refer to the suffix table on page 2, respect the indicated level. xample: O STP 4 Select voltage. Refer to standard voltages on page 3. xample: 230V / 50/60 z STP 5 inal catalogue / ordering number. xample: N 83021 O 230V / 50/60 z OPTIONS & SSORIS catalogue number spare part kit no. (2) mounting bracket ~ / = S 3021 123670 S 3022 123670 S 3031 131237 S 3032 131237 S 3071 117644 S 3072 117644 S 3081 117645 S 3082 117645 S 3121 132251 S 3122 132251 S 3131 132253 S 3132 132253 S 3171 117646 S 3172 117646 S 3181 117647 S 3182 117647 S 3221 132251 S 3222 132251 S 3231 132253 S 3232 132253 S 31 117648 S 32 117648 S 3281 117649 S 3282 117649 Select 8 for NPT NSI 1.20.3 or select for ISO (228/1) (2) Standard prefixes/suffixes are also applicable to kits Mounting holes in body ORRIN XMPS VVS: prefix (3) pipe thread basic number (3) S 8 3021 24V / WSMT 3022 O 24V / NT 3021 230V / 50/60 z WSM 3022 24V / N 8 3231 O 24V / WS 3021 O 24V / M 8 3221 230V / 50/60 z PV 8 3032 O 24V / 3022 O 240V / 50/60 z ORRIN XMPS ITS: prefix basic number 131237 (4) PV 123670 N 131237 WSM 123670 suffix (3) Prefix and V should always be used in conjunction with change letter in the basic number (4) asic kit number applies to S coil construction voltage suffix Pneutrol International td are Platinium istributors for SO Numatics ontact us : 5 aulside rive, ntrim, Northern Ireland, T 2U www.valves-direct.com Sales@pneutrol.com Tel: +44 (0) 28 9448 1800
XPNTION O TMPRTUR RNS O SONOI VVS Valve temperature range Operator ambient temperature range Total temperature range SRIS 3 The valve temperature range (TS) is determined by the selected seal material, the temperature range for proper operation of the valve and sometimes by the fluid (e.g. steam) The operator ambient temperature range is determined by the selected level and the safety code The temperature range of the complete solenoid valve is determined by the limitations of both temperature ranges above TRI RTRISTIS oil insulation class lectrical safety I 335 Standard voltages (=) 24V - 48V; llowable voltage variation ± 10% (~) 24V - 48V - 115V - 230V/50/60z; Other voltages are available on request prefix option asic (P) ratings operator ambient electrical replacement coil / kit inrush holding hot/cold temperature enclosure safety code ~ ~ = range protection ~ = (V) (V) (W) (W) ( ) (1) (N 60529) 230V/50/60 z 24V/ S 10,0 10,0 10,0 9,0/11,2-40 to +55 N 60730 IP65, moulded 123664-017 400425-142 01 WP/WS 10,0 10,0 10,0 9,0/11,2-40 to +55 N 60730 IP67, steel /SS 400915-017 400913-142 03 N/WSN 10,0 10,0 10,0 9,0/11,2-60 to +40/60 II2 x d II b T6/T5, II2 x t III b IP67, alu./ss 400915-017 400913-142 05 M/WSM 10,0 10,0 10,0 9,0/11,2-40 to +40 II2 x e mb II T3, II2 x t 21 IP67, steel /SS 400915-017 400913-142 03 PV - - - 9,0/11,2-40 to +55 II2 x mb II T4, II2 x m 21 IP67, moulded - - (3) 06 /V 12,0 12,0 12,0 9,3/11,6-40 to +52/40 NM type 7 and 9 NM 4X 6002-058 238714-006 07 Medium Power (MP) S 5,8 5,8 5,8 5,2/5,7-40 to +90 N 60730 IP65, moulded 400924-297 400923-442 02 WP/WS 5,8 5,8 5,8 5,2/5,7-40 to +90 N 60730 IP67, steel /SS 400921-297 400914-442 04 N/WSN 5,8 5,8 5,8 5,2/5,7-60 to +60/75/90 II2 x d II b T6/T5/T4, II2 x t III b IP67, alu./ss 400921-297 400914-442 05 M/WSM 5,8 5,8 5,8 5,2/5,7-40 to +40/75/90 II2 x e mb II T5/T4/T3, II2 x t 21 IP67, steel /SS 400921-297 400914-442 04 Reduced Power (RP) (4) S 3,7 3,7 3,7 3,2/3,6-40 to +55 N 60730 IP65, moulded - (4) 400923-042 02 WP/WS 3,7 3,7 3,7 3,2/3,6-40 to +55 N 60730 IP67, steel /SS - (4) 400914-242 04 N/WSN 3,7 3,7 3,7 3,2/3,6-60 to +60 II2 x d II b T6, II2 x t III b IP67, alu./ss - (4) 400914-242 05 M/WSM 3,7 3,7 3,7 3,2/3,6-40 to +40/55 II2 x e mb II T6/T5, II2 x t 21 IP67, steel /SS - (4) 400914-242 04 (1) Temperature range can be limited by sealings (2) Refer to the dimensional drawings on page 4 and 5 (3) Multiple coil kits are available under TX/Ix, contact us (4) (~) limited to 1V/50/60z or 125V/ - Not available type (2) TRI ONNTIONS prefix S WP, WS, M, WSM N, WSN NT, WSNT connection Spade plug connector with cable gland N175301-803 (ISO 4400) for cables with an outer diameter from 6 to 10 mm M20 cable gland for cables with an outer diameter from 7 to 12 mm. With an internal and external facility for an earthing or bonding conductor 1/2" NPT threaded cable entry. nclosures are supplied without cable gland M20 x 1,5 threaded cable entry. nclosures are supplied without cable gland Pneutrol International td are Platinium istributors for SO Numatics ontact us : 5 aulside rive, ntrim, Northern Ireland, T 2U www.valves-direct.com Sales@pneutrol.com Tel: +44 (0) 28 9448 1800
SRIS 3 ITION OPTIONS x mb/m (prefix "PV") solenoid can be supplied with various cable lengths ompliance with "U", "S" and other local approvals available on request Manual Reset constructions suitable for -40 are available on request INSTTION Multi language installation/maintenance instructions are included with each valve The solenoid valves can be mounted in any position without affecting operation The mounting holes are provided in the valve body Threaded pipe connection identifier is 8 = NPT (NSI 1.20.3); = (ISO 228/1) eclarations of conformity are available on request x e mb Prefix "M" execution: solenoid enclosure has a cable gland with integral strain relief for cables with an o.d. from 7 to 12 mm and is provided with an internal and external connection facility for an earthing or bonding conductor x d Prefix "N/WSN" enclosure is provided with a 1/2" NPT threaded entry hole, M20 x 1,5 (prefix "T") is optional oth are supplied without cable gland ll solenoids with metal enclosure are provided with switch-off peak voltage suppression diodes To comply with I 61508 (SI) the valves must be provided with a specific exhaust protector (as shown on page 6) or equal IMNSIONS (mm), WIT (kg) TYP 01: TYP 02: poxy moulded poxy moulded S: I 335 / ISO 4400 S: I 335 / ISO 4400 3021 / 022 / 031 / 032 3121 / 122 / 131 / 132 / 221 / 222 / 231 / 232 N 12 23 M M TYP 03: TYP 04: Metal, epoxy coated / ISI 316 SS Metal, epoxy coated / ISI 316 SS WP / WS: I 335 WP / WS: I 335 M / WSM: N/I 60079-7+18, 612-1 M / WSM: N/I 60079-7+18, 612-1 3021 / 022 / 031 / 032 3121 / 122 / 131 / 132 / 221 / 222 / 231 / 232 12 23 Pneutrol International td are Platinium istributors for SO Numatics ontact us : 5 aulside rive, ntrim, Northern Ireland, T 2U www.valves-direct.com Sales@pneutrol.com Tel: +44 (0) 28 9448 1800
SRIS 3 IMNSIONS (mm), WIT (kg) TYP 05: TYP 06: luminium, epoxy coated / ISI 316 SS poxy encapsulated N / WSN: N/I 60079-1, 60079-31 PV: N/I 60079-18, 612-18 3 021 / 022 / 031 / 032 / 121 / 122 / 3131 / 132 / 221 / 222 / 231 / 232 3001 / 002 / 011 / 012 1/2 NPT 9 15 Ø5,5 Ø5,5 TYP 07: poxy encapsulated and V: NM type 7, 9 / IS-6 NSI 3021 / 022 / 031 / 032 Ø5,5 type prefix/option level M N weight 01 S P 45 30 24 79 138 155 91 85 50 30 55 67 1,20 kg 02 S MP/RP 50 30 24 98 149 95 91 56 33 55 86-1,30 kg 03 WP, WS, M, WSM P 77 30 24 98 155 120 81 55 86 - - - 1,20 kg 04 WP, WS, M, WSM MP/RP 77 30 24 101 158 120 81 55 89 - - - 1,30 kg 05 N, WSN P/MP/RP 97 30 24 125 102 54 55 88 176 113 - - 2,70 kg 06 PV P 45 30 24 86 137 72 67 45 55 74 - - 1,20 kg 07, V P 50 30 24 87 138 77 51 55 75 - - - 1,20 kg Pneutrol International td are Platinium istributors for SO Numatics ontact us : 5 aulside rive, ntrim, Northern Ireland, T 2U www.valves-direct.com Sales@pneutrol.com Tel: +44 (0) 28 9448 1800
SRIS 3 STION RWIN 1 XUST PROTTOR 2 3 xecution : Reduced Power Tamperproof XUST PROTTOR ORR NUMRS ¼ ISO 228/1 -MV110014 brass/nickel NPT -PV110014 ISO 228/1 -VX110014 stainless steel NPT -PV110014 Inox Pneutrol International td are Platinium istributors for SO Numatics ontact us : 5 aulside rive, ntrim, Northern Ireland, T 2U www.valves-direct.com Sales@pneutrol.com Tel: +44 (0) 28 9448 1800