The American Standard - PDF Free Download

Team Up with rowning and get a year warranty on Shaft Mounts and elt Drives. Team rowning will keep you in play, not sidelined by poor performance. The American Standard 4

SMTP rowning TorqTaper Plus Shaft Mounts... Unlike competitive bushing systems that mount only from the front or back of the reducer (or require bushings on both sides), TorqTaper Plus uses a single tapered bushing that easily installs from either front or back depending on your space limitations and available shaft length. This patented feature simplifies replacement of any competitive unit. Patented arrier Seal System Combines a vring face seal, grease filled labyrinth and rotating outer flinger to provide triple protection against contamination and oil seal damage. Standard on all shafts. 5

The New Way... Your Way 4 5 7 6 6

SMTP 1 Check Out These Additional Features of TorqTaper Plus Reducers 1. Unique, patented single bushing mounting system Tapered bushing mounts from either side on the 715. Tapered stabilizer ring minimizes wobble and resists fretting corrosion. End cap seals quill end from contamination 4. Industrial strength seal systems Patented barrier seal system includes standard double lip oil seals with vring face seal, grease packed labyrinth and external flinger 5. Carburized and ground gearing throughout AGMA class 1 minimum 6. Tapered roller bearings on all shafts 7. Increased shaft diameters; higher overhung load ratings Plus... Depending upon size, available ratios include 5, 9, 15, 5 and new 5:1 ratio Increased horsepower ratings, allows downsizing on many applications Predrilled and tapped face mount holes 7

Example No. 1 Shaft Mount Application Selection and Ordering Information A shaft mount reducer and belt drive are required for a bucket conveyor, which will be uniformly loaded and operated 16 to 4 hours per day at 81. The conveyor requires 15 hp. The reducer will be mounted on the conveyor head shaft which is 7/16" diameter. The customer wants to mount the 1750 54T frame motor on the reducer. The customer has also requested a backstop for the reducer. 1. Determine the Load Classification From the AGMA Application Classification numbers, note that the load class is II for a uniformly loaded bucket conveyor operating over hours per day.. Determine the Speed Reducer Required From the Reducer Selection Chart for Class II Service, select a reducer for 15 hp and 8189, which in this case is a 07SMTP15 or 07SMTP09. Choose the 07SMTP15, as the larger ratio will require the most compact and generally most economical belt drive. Refer to the Shaft Mount Accessories section for a bushing and torque arm. A 07TP07 bushing is required for the reducer. Select the 07TAP torque arm. 5. Select the elt Drive Note that the belt centers for this motor and reducer combination are.4 to 9.66. Note that 4." is the minimum sheave pitch diameter for the 07SMTP15 reducer chosen in Step. Reducer input speed = 81 (conveyor speed) x 14.787 (Exact Reducer Ratio) = 1197. From the Shaft Mount Accessories section preselected belt drive tables select a belt drive with a center distance near the midpoint of the.4 to 9.66. This drive (1197 driven speed) consists of a 5V68 sheave with a 1 5/8 bushing, a 5V94 sheave with a 1 7/16 bushing and two 660 gripnotch belts. 6. Select the elt Guard Select the guard. Notice from the table that the CD range with the belt guard is.00 to 4.00" and the maximum reducer sheave that will fit into the belt guard in the top mount position is 4". Note that the part number, GP4 48 with 07GMKP, kit hardware required to mount the guard onto the reducer. 7. List Components:. Select the Motor Mount Determine if a top mount or side mount configuration is required. Reference the motor mount tables in the Shaft Mount Accessories section for dimensions. After consulting the customer, it was determined that the top mount configuration was desired. Select the correct motor mount supports, motor mount adapter and motor base: MMS07L, MMA07, M007. 4. Select the ackstop Select the 07SP backstop from the Shaft Mount Accessories section. 1, 07SMTP15 Reducer 1, 07TP07 ushing 1, 07TAP Arm 1, MMS07L Motor Mount Support 1, MMA07 Motor Mount Adapter 1, M007 Motor ase 1, 07SP ackstop 1, 1 5/8 ushing 1, 5V68 Sheave 1, 1 7/16 ushing 1, 5V94 Sheave, 660 elts 1, GP4 48/ 07GMKP elt Guard Note: See Application Considerations on back cover. 8

SMTP Example No. Screw Conveyor Application A screw conveyor drive is required to convey dry cement powder. The conveyor will be uniformly fed and operated 1 to 16 hours per day. The screw is 14" diameter and has a 7/16" bore with two holes. The conveyor requires 5 hp and will operate at 60. The motor is a 1750 184T frame. The customer wants the trough end, waste pack, belt drive, belt guard and motor mount. 1. Determine the Load Classification From the AGMA Application Classification numbers, note that the load class is II for a uniformly fed screw conveyor operating over hours per day.. Determine the Speed Reducer Required From the Reducer Selection Chart for Class II Service select a reducer for 5 hp and 60, which in this case is a 115SMTP09, 115SMTP15 or 115SMTP5 for 5577. Choose the 115SMTP5 as the larger ratio will require the most compact and generally most economical belt drive.. Establish Sealing Required for Screw Conveyor The waste pack cartridge is well suited for dry, abrasive materials such as cement powder. Specify the optional waste pack cartridge for the 115 shaft mount selected. From the Shaft Mount Accessories section, select part 1150WPP. 4. Select the Screw Conveyor Adapter and Screw Conveyor Shaft Note that the customer requested a 7/16" drive shaft with a two hole arrangement for the 14" diameter screw. From the table select the 115SCAP and the 115DSP07 using the basic reducer size, screw diameter and shaft size. 5. Select the Trough End From the Shaft Mount Accessories section, select the SCTE14 x 7/16 trough end. 6. Select the Motor Mount First determine if the top mount or side mount configuration is required. Reference the motor mount tables in the Shaft Mount Accessories section for dimensions. After consulting with the customer it was determined that the top mount was desired. Select the MMS115, MMA7115 and M7115. Check the dimensions from the motor mount table. Note that the high motor mount must be used with this size screw. The value of 4." needs to be added to the minimum center distance on the high supports to ensure that the motor mount clears the screw conveyor. 7. Select the elt Drive Selection and Ordering Information Note that the belt center distance range for this reducer and motor combination is 17.50" to 4.4". Note the minimum sheave pitch diameter for the 115SMTP5 is.4". Reducer input speed = 60 (conveyor speed) x 4.8558 (Exact Reducer Ratio) = 1491. From the preselected belt drive tables, select a belt drive with a center distance greater than 17.5 + 4. = 1.8". This drive (1496 driven speed) consists of a AK54 sheave with 1 1/8" bushing, AK64 sheave with 1 1/8" bushing and two 58 Gripnotch belts. 8. Select the elt Guard Select the guard. Notice from the table that the CD range with the belt guard is 18.0 to 0.00" and the maximum reducer sheave that will fit into the belt guard in the top mount position is 14". Note that the part number is GP14 180/115GMKP, kit hardware required to mount the guard onto the reducer. 9. List the Components: 1, 115SMTP5 Reducer 1, 1150WWP Waste Pack Cartridge 1, 115SCAP Screw Conveyor Adapter 1, 115DSP07 Screw Conveyor Drive Shaft Kit 1, SCTE14x 7/16 Trough End 1, MMS115 Motor Mount Support Reducer SMTP Exact Ratios Ratio Symbols 05 09 15 5 5 7 115 5.0588 4.7000 8.805 8.815 14.876 14.7759 4.750 4.8558 0 5.5 8.87 14.91 4.7409 07 5.1579 8.808 14.7870 4.7094 15 5.1667 8.848 14.8187 4.850 07 15 5.1111 4.884 8.795 8.860 14.9704 14.5744 4.769 4.4118 407 415 5.0000 5.08 1.684 1.979 5.0000 5.840 507 1.684 5.846 608 1.9118 5.6555 800 4.9648 Note: See Application Considerations on back cover. 1, MMA7115 Motor Mount Adapter 1, M7115 Motor ase, 1 1/8 ushing 1, AK54 Sheave 1, AK64 Sheave 1, 64 elt 1, GP14 180/ 115GMKP elt Guard 4.8778 4.9487 4.649 5.0000 4.8154 4.8791 4.051 9

Application AGMA Class Numbers Up to ours Per Day ours Per Day Over ours Per Day AGITATORS (Mixers) Pure Liquids I I II Liquids and Solids I II II Liquids Variable Density I II II LOWERS Centrifugal & Vane I I II Lobe I II II Vane I II II REWING AND DISTILLING ottling Machinery I I II rew Kettles Continuous Duty II II II Cookers Continuous Duty II II II Mash Tubs Continuous Duty II II II Scale opper Frequent Starts II II II CAN FILLING MACINES I I II CAR DUMPERS II III III CAR PULLERS I II II CLARIFIERS I I II CLASSIFIERS I II II CLAY WORKING MACINERY rick Presses II III III riquette Machines II III III Pug Mills I II II COMPACTORS COMPRESSORS Centrifugal I I II Lobe I II II Reciprocating, MultiCylinder II II III Reciprocating, SingleCylinder III III III CONVEYORS GENERAL PURPOSE Includes Apron, Assembly, elt, ucket Chain, Flight, Oven, and Screw Uniformly Loaded or Fed I I II eavy Duty Not Uniformly Fed I II II Severe Duty Reciprocating or Shaker II III III CRANES Dry Dock Main oist Auxiliary oist oom oist Slewing Drive Traction Drive Container Main oist oom oist Trolley Drive Gantry Drive Traction Drive Mill Duty Main oist Auxiliary ridge Travel Trolley Travel Industrial Duty Main Auxiliary ridge Travel Trolley Travel CRUSERS Stone or Ore III III III DREDGES Cable Reels II II II Conveyors II II II Cutter ead Drives III III III Pumps III III III Screen Drives III III III Stackers II II II Winches II II II ELEVATORS ucket I II II Centrifugal Discharge I I II Escalators I I II Freight I II II Gravity Discharge I I II EXTRUDERS General II II II Plastics Variable Speed Drive III III III Speed Drive III III III Rubber Continuous Screw Operation III III III Intermittent Screw Operation III III III FANS Centrifugal I I II AGMA Application Classification Numbers Application AGMA Class Numbers Up to ours Per Day ours Per Day Over ours Per Day FANS (Cont d) Cooling Towers III III III Forced Draft II II II Induced Draft II II II Industrial & Mine II II II FEEDERS Apron I II II elt I II II Disc I I II Reciprocating II III III Screw I II II FOOD INDUSTRY Cereal Cooker I I II Dough Mixer II II II Meat Grinders II II II Slicers I II II GENERATORS AND EXCITERS II II II AMMER MILLS III III III OISTS eavy Duty Medium Duty Skip oist LAUNDRY TUMLERS II II II LAUNDRY WASERS II II III LUMER INDUSTRY arkers Spindle Feed II II II Main Drive III III III Conveyors urner II II II Main or eavy Duty II II II Main Log III III III Resaw, MerryGoRound II II II Slab III III III Transfer II II II Chains Floor II II II Green II II III CutOffSaws Chain II II III Drag II II III Debarking Drums III III III Feeds Edger II II II Gang II III III Trimmer II II II Log Deck III III III Log auls Incline Well Type III III III Log Turning Devices III III III Planer Feed II II II Planer Tilting oists II II II Rolls LiveOff rg Roll Cases III III III Sorting Table II II II Tipple oist II II II Transfer Chain II II III Craneway II II III Tray Drives II II II Veneer Lathe Drives II II II METAL MILLS Draw ench Carriage and Main Drive II II II Runout Table NonReversing Group Drives II II II Individual Drives III III III Reversing III III III Slab Pushers II II II Shears III III III Wire Drawing II II II Wire Winding Machine II II II METAL STRIP PROCESSING MACINERY ridges II II II Collers & Uncoilers I I II Edge Trimmers I II II Flatteners II II II Loopers (Accumulators) I I I Pinch Rolls II II II Scrap Choppers II II II Shears III III III Slitters I II II MILLS, ROTARY TYPE all & Rod Spur Ring Gear III III III elical Ring Gear II II II Direct Connected III III III

SMTP Application AGMA Application Classification Numbers AGMA Class Numbers Up to ours Per Day ours Per Day Over ours Per Day MILLS, ROTARY TYPE (Cont d) Cement Kilns II II II Dryers & Coolers II II II PAPER MILLS 1) Agitator (Mixer) II II II Agitator For Pure Liquors II II II arking Drums III III III arkers Mechanical III III III eater II II II reaker Stack II II II Calendar ) II II II Chipper III III III Chip Feeder II II II Coating Rolls II II II Conveyors Chip, ark, Chemical II II II Log (Including Slab) III III III Couch Rolls II II II Cutter III III III Cylinder Molds II II II Dryers ) Paper Machine II II II Conveyor Type II II II Embosser II II II Extruder II II II Fourdrinier Rolls (Includes Lump reaker, Dandy Roll, Wire Turning, and Return Rolls) II II II Jordan II II II Kiln Drive II II II Mt. ope Roll II II II Paper Rolls II II II Platter II II II Presses Felt Suction II II II Pulper III III III Pumps Vacuum II II II Reel (Surface Type) II II II Screens Chip II II II R otary II II II Vibrating III III III Press II II II Supercalendar II II II Thickener (AC Motor) II II II Thickener (DC Motor) II II II Washer (AC Motor) II II II Washer (DC Motor) II II II Wind and Unwind Stand I I I II II PLASTICS INDUSTRY PRIMARY PROCESSING Intensive Internal Mixers atch Mixers III III III Continuous Mixers II II II atch Drop Mill Smooth Rolls II II II Continuous Feed, olding & lend Mill II II II Calendars II II II PLASTICS INDUSTRY SECONDARY PROCESSING low Molders II II II Coating II II II Film II II II Pipe II II II PrePlasticizers II II II Rods II II II Sheet II II II Tubing II II II PULLERS ARGE AUL II II II PUMPS Centrifugal I I II Proportioning II II II Reciprocating Single Acting, or more Cylinders II II II Double Acting, or more Cylinders II II II Rotary Gear Type I I II Lobe I I II Vane I I II RUER INDUSTRY Intensive Internal Mixers atch Mixers III III III Continuous Mixers II II II Mixing Mill Smooth Rolls II II II 1 or Corrugated Rolls III III III RUER INDUSTRY (Cont d) Application AGMA Class Numbers Up to Over ours Per Day ours Per Day ours Per Day atch Drop Mill Smooth Rolls II II II Cracker Warmer Roll, 1 Corrugated Roll III III III Cracker Corrugated Rolls III III III olding, Feed & lend Mill Rolls II II II Refiner Rolls II II II Calendars II II II SAND MULLER II II II SEWAGE DISPOSAL EQUIPMENT ar Screens II II II Chemical Feeder II II II Dewatering Screens II II II Scum reakers II II II Slow or Rapid Mixers II II II Sludge Collectors II II II Thickener II II II Vacuum Filters II II II SCREENS Air Washing I I II Rotary Stone or Gravel II II II Traveling Water Intake I I I SCREW CONVEYORS Uniformly Loaded or Fed I I II eavy Duty I II II SUGAR INDUSTRY eet Slicer III III III Cane Knives II II II Crushers II II II Mills (Low Speed End) III III III TEXTILE INDUSTRY atchers II II II Calendars II II II Cards II II II Dry Cans II II II Dyeing Machinery II II II Looms II II II Mangles II II II Nappers II II II Pads II II II Slashers II II II Soapers II II II Spinners II II II Tenter Frames II II II Washers II II II Winders II II II Notes: 1) The Class numbers listed in the table for paper mill applications are consistent with those shown in TAPPI (Technical Association of Pulp and Paper Industry) Technical information sheet 040618 1967, Service Factors for Gears on Major Equipment in the Pulp and Paper Industry. ) Antifriction bearings only. Contact Application Engineering (1 800 66 09) for the selection of AGMA Class Numbers in these applications. 11

SMTP/SMFP Selection Chart Class I Service (1.0 S.F.) RPM Reducer Minimum Sheave P.D. 1/4 MOTOR 5 50 7SMTP5. 7SMTP5. 7SMTP15.8 7SMTP09 4.7 51 80 7SMTP5. 7SMTP15.8 7SMTP09 4.7 81 89 7SMTP15.8 7SMTP09 4.7 90 7SMTP15.8 7SMTP09 4.7 7SMTP05 4.6 11 00 7SMTP09 4.7 7SMTP05 4.6 01 400 7SMTP05 4.6 1/ MOTOR 5 50 7SMTP5. 7SMTP5. 7SMTP15.8 7SMTP09 4.7 51 80 7SMTP5. 7SMTP15.8 7SMTP09 4.7 81 89 7SMTP15.8 7SMTP09 4.7 90 7SMTP15.8 7SMTP09 4.7 7SMTP05 4.6 11 00 7SMTP09 4.7 7SMTP05 4.6 01 400 7SMTP05 4.6 1/ MOTOR 5 50 7SMTP5. 7SMTP5. 7SMTP15.8 7SMTP09 4.7 51 80 7SMTP5. 7SMTP15.8 7SMTP09 4.7 81 89 7SMTP15.8 7SMTP09 4.7 90 7SMTP15.8 7SMTP09 4.7 7SMTP05 4.6 11 00 7SMTP09 4.7 7SMTP05 4.6 01 400 7SMTP05 4.6 /4 MOTOR 5 0SMTP5.8 0SMTP5.8 0SMTP15.8 0SMTP09.8 6 7 115SMTP5.4 115SMTP5.4 115SMTP15.4 115SMTP09.4 8 50 7SMTP5. 7SMTP5. 7SMTP15.6 7SMTP09 4.4 RPM Reducer Minimum Sheave P.D. /4 MOTOR (Cont d) 51 80 7SMTP5. 7SMTP15.6 7SMTP09 4.4 81 89 7SMTP15.6 7SMTP09 4.4 90 7SMTP15.6 7SMTP09 4.4 7SMTP05 4.6 11 00 7SMTP09 4.4 7SMTP05 4.6 01 400 7SMTP05 4.6 1 MOTOR 5 6 0SMTP5.8 0SMTP5.8 0SMTP15.8 0SMTP09.8 7 9 115SMTP5.4 115SMTP5.4 115SMTP15.4 115SMTP09.4 50 7SMTP5. 7SMTP5. 7SMTP15.8 7SMTP09 4.7 51 80 7SMTP5. 7SMTP15.8 7SMTP09 4.7 81 89 7SMTP15.8 7SMTP09 4.7 90 7SMTP15.8 7SMTP09 4.7 7SMTP05 4.6 11 00 7SMTP09 4.7 7SMTP05 4.6 01 400 7SMTP05 4.6 1 1/ MOTOR 5 07SMTP5 4. 07SMTP5 4. 07SMTP15 4. 07SMTP09 4.4 6 0SMTP5.8 0SMTP5.8 0SMTP15.8 0SMTP09 4. 11 15 115SMTP5.4 115SMTP5.4 115SMTP15.4 115SMTP09.4 16 50 7SMTP5. 7SMTP5. 7SMTP15.6 7SMTP09 4.4 51 80 7SMTP5. 7SMTP15.6 7SMTP09 4.4 81 89 7SMTP15.6 7SMTP09 4.4 90 7SMTP15.6 7SMTP09 4.4 7SMTP05 4.6 RPM Reducer Minimum Sheave P.D. 1 1/ MOTOR (Cont d) 11 00 7SMTP09 4.4 7SMTP05 4.6 01 400 7SMTP05 4.6 MOTOR 5 8 07SMTP5 4. 07SMTP5 4. 07SMTP15 4. 07SMTP09 4.4 9 14 0SMTP5.8 0SMTP5.8 0SMTP15.8 0SMTP09.8 15 0 115SMTP5.4 115SMTP5.4 115SMTP15.4 115SMTP09.4 1 50 7SMTP5. 7SMTP5. 7SMTP15.7 7SMTP09 4.5 51 80 7SMTP5. 7SMTP15.7 7SMTP09 4.5 81 89 7SMTP15.7 7SMTP09 4.5 90 7SMTP15.7 7SMTP09 4.5 7SMTP05 4.6 11 00 7SMTP09 4.5 7SMTP05 4.6 01 400 7SMTP05 4.6 MOTOR 5 7 15SMTP5 5.6 15SMTP5 5.6 15SMTP15 5.6 15SMTP09 5.6 8 1 07SMTP5 4. 07SMTP5 4. 07SMTP15 4. 07SMTP09 4. 1 0SMTP5.8 0SMTP5.8 0SMTP15.8 0SMTP09 4.0 1 115SMTP5.4 115SMTP5.4 115SMTP15.4 115SMTP09.4 50 7SMTP5. 7SMTP5. 7SMTP15.6 7SMTP09 4.4 51 80 7SMTP5. 7SMTP15.6 7SMTP09 4.4 81 89 7SMTP15.6 7SMTP09 4.4 90 7SMTP15.6 7SMTP09 4.4 7SMTP05 4.6 1

SMTP SMTP/SMFP Selection Chart Class I Service (1.0 S.F.) RPM Reducer Minimum Sheave P.D. MOTOR (Cont d) 11 00 7SMTP09 4.4 7SMTP05 4.6 01 400 7SMTP05 4.6 5 MOTOR 57 07SMTP5 6.0 07SMTP5 6.0 07SMTP15 6.0 07SMTP09 6.0 8 1 15SMTP5 5.6 15SMTP5 5.6 15SMTP15 5.6 15SMTP09 5.6 14 1 07SMTP5 4. 07SMTP5 4. 07SMTP15 4. 07SMTP09 4. 8 0SMTP5.8 0SMTP5.8 0SMTP15.8 0SMTP09.8 9 50 115SMTP5.4 115SMTP5.4 115SMTP15.4 115SMTP09.4 51 54 115SMTP5.4 115SMTP15.4 115SMTP09.4 55 80 7SMTP5.8 7SMTP15.8 7SMTP09 4. 81 89 7SMTP15.8 7SMTP09 4. 90 7SMTP15.8 7SMTP09 4. 7SMTP05 4.6 11 00 7SMTP09 4. 7SMTP05 4.6 01 400 7SMTP05 4.6 7 1/ MOTOR 5 407SMTP5 6.4 407SMTP15 6.4 6 15SMTP5 6.4 15SMTP5 6.4 15SMTP15 6.4 15SMTP09 7.1 7 1 07SMTP5 6.0 07SMTP5 6.0 07SMTP15 6.0 07SMTP09 6.5 1 0 15SMTP5 5.6 15SMTP5 5.6 15SMTP15 5.6 15SMTP09 5.6 1 07SMTP5 4. 07SMTP5 4. 07SMTP15 4. 07SMTP09 4. 4 50 0SMTP5.8 0SMTP5.8 0SMTP15.8 0SMTP09.8 RPM Reducer Minimum Sheave P.D. 7 1/ MOTOR (Cont d) 51 58 0SMTP5.8 0SMTP15.8 0SMTP09.8 59 80 115SMTP5.4 115SMTP15.4 115SMTP09.4 81 8 115SMTP15.4 115SMTP09.4 84 89 7SMTP15.8 7SMTP09 4. 90 7SMTP15.8 7SMTP09 4. 115SMTP05 9.8 11 160 7SMTP09 4. 115SMTP05 9.8 161 00 7SMTP09 4. 7SMTP05.8 01 400 7SMTP05.8 MOTOR 5 7 407SMTP5 6.4 407SMTP15 6.4 8 9 15SMTP5 6.4 15SMTP5 6.4 15SMTP15 6.4 15SMTP09 7.1 16 07SMTP5 6.0 07SMTP5 6.0 07SMTP15 6.0 07SMTP09 6.1 17 7 15SMTP5 5.6 15SMTP5 5.6 15SMTP15 5.6 15SMTP09 5.6 8 46 07SMTP5 4. 07SMTP5 4. 07SMTP15 4. 07SMTP09 4. 47 50 07SMTP5 4. 0SMTP5.8 0SMTP15.8 0SMTP09.8 51 80 0SMTP5.8 0SMTP15.8 0SMTP09.8 81 89 115SMTP15.6 115SMTP09.6 90 114 115SMTP15.6 115SMTP09.6 115SMTP05 9.8 115 7SMTP15.6 7SMTP09 4.1 115SMTP05 9.8 11 00 7SMTP09 4.1 115SMTP05 9.8 01 44 115SMTP05 9.8 45 400 7SMTP05.6 15 MOTOR 5 7 415SMTP5 7.1 415SMTP15 7.1 RPM Reducer Minimum Sheave P.D. 15 MOTOR (Cont d) 8 11 407SMTP5 6.4 407SMTP15 6.4 1 14 15SMTP5 6.4 15SMTP5 6.4 15SMTP15 6.4 15SMTP09 7.1 15 5 07SMTP5 6.0 07SMTP5 6.0 07SMTP15 6.0 07SMTP09 6.1 6 4 15SMTP5 5.6 15SMTP5 5.6 15SMTP15 5.6 15SMTP09 5.6 4 50 07SMTP5 4. 07SMTP5 4. 07SMTP15 4. 07SMTP09 4. 51 80 07SMTP5 4. 07SMTP15 4. 07SMTP09 4. 81 89 0SMTP15.8 0SMTP09.8 90 11 0SMTP15.8 0SMTP09.8 0SMTP05 6.4 1 0SMTP15.8 115SMTP09.4 0SMTP05 6.4 11 161 115SMTP09.4 0SMTP05 6.4 16 00 115SMTP09.4 115SMTP05 9.6 01 400 115SMTP05 9.6 0 MOTOR 5 6 507SMTP5 7.9 507SMTP15 8. 7 9 415SMTP5 7.1 415SMTP15 7.1 14 407SMTP5 6.4 407SMTP15 6.4 15 19 15SMTP5 6.4 15SMTP5 6.4 15SMTP15 6.4 15SMTP09 7.6 0 4 07SMTP5 6.0 07SMTP5 6.0 07SMTP15 6.0 07SMTP09 6.1 5 50 15SMTP5 5.6 15SMTP5 5.6 15SMTP15 5.6 15SMTP09 5.6 51 61 15SMTP5 5.6 15SMTP15 5.6 15SMTP09 5.6 61 80 07SMTP5 4. 07SMTP15 4. 07SMTP09 4. 1

SMTP/SMFP Selection Chart Class I Service (1.0 S.F.) RPM Reducer Minimum Sheave P.D. 0 MOTOR (Cont d) 81 89 07SMTP15 4. 07SMTP09 4. 90 07SMTP15 4. 07SMTP09 4. 07SMTP05 9.8 11 0SMTP15.8 0SMTP09.8 0SMTP05 6.8 11 00 0SMTP09.8 0SMTP05 6.8 01 44 0SMTP05 6.8 45 400 115SMTP05 9.4 5 MOTOR 5 608SMTP5 8.0 608SMTP15 11.4 6 8 507SMTP5 7.9 507SMTP15 8.7 9 1 415SMTP5 7.1 415SMTP15 7.1 1 18 407SMTP5 6.4 407SMTP15 6.4 19 4 15SMTP5 6.4 15SMTP5 6.4 15SMTP15 6.4 15SMTP09 7.5 5 44 07SMTP5 6.0 07SMTP5 6.0 07SMTP15 6.0 07SMTP09 6.1 45 50 15SMTP5 5.6 15SMTP5 5.6 15SMTP15 5.6 15SMTP09 5.6 51 80 15SMTP5 5.6 15SMTP15 5.6 15SMTP09 5.6 81 89 07SMTP15 4. 07SMTP09 4.7 90 15 07SMTP15 4. 07SMTP09 4.7 15SMTP05 6. 16 07SMTP15 4. 07SMTP09 4.7 07SMTP05 9.6 11 159 07SMTP09 4.7 07SMTP05 9.6 160 00 0SMTP09.8 0SMTP05 6.8 01 7 0SMTP05 6.8 8 400 115SMTP05 9. 0 MOTOR 5 6 608SMTP5 8.1 608SMTP15 11.4 7 507SMTP5 7.9 507SMTP15 8.9 11 15 415SMTP5 7.1 415SMTP15 7.1 16 407SMTP5 6.4 407SMTP15 6.4 RPM Reducer Notes: Requires fan kit. Requires pump and cooler kit. Contact Application Engineering (1 800 66 09) for the selection of an enclosed gear drive. 14 Minimum Sheave P.D. 0 MOTOR (Cont d) 4 0 15SMTP5 6.4 15SMTP5 6.4 15SMTP15 6.4 15SMTP09 7.1 1 50 07SMTP5 6.0 07SMTP5 6.0 07SMTP15 6.0 07SMTP09 6.0 51 55 07SMTP5 6.0 07SMTP15 6.0 07SMTP09 6.0 56 80 15SMTP5 5.6 15SMTP15 5.6 15SMTP09 5.6 81 89 15SMTP15 5.6 15SMTP09 5.6 90 15SMTP15 5.6 15SMTP09 5.6 15SMTP05 6. 4 07SMTP15 4. 07SMTP09 5. 15SMTP05 6. 11 16 07SMTP09 5. 15SMTP05 6. 16 00 07SMTP09 5. 07SMTP05 9.5 01 15 07SMTP05 9.5 15 400 0SMTP05 6.7 40 MOTOR 5 800SMTP5 1.0 6 9 608SMTP5 8.1 608SMTP15 1.7 14 507SMTP5 7.9 507SMTP15 8. 15 0 415SMTP5 7.1 415SMTP15 7.1 1 1 407SMTP5 6.4 407SMTP15 6.4 4 15SMTP5 6.4 15SMTP5 6.4 15SMTP15 6.4 15SMTP09 7.4 44 50 07SMTP5 6.0 07SMTP5 6.0 07SMTP15 6.0 07SMTP09 6.9 51 76 07SMTP5 6.0 07SMTP15 6.0 07SMTP09 6.9 77 80 07SMTP5 6.0 07SMTP15 6.0 15SMTP09 5.7 81 89 07SMTP15 6.0 15SMTP09 5.6 90 15SMTP15 5.6 15SMTP09 5.6 07SMTP05 7.8 11 156 15SMTP09 5.8 15SMTP05 6. RPM Reducer Minimum Sheave P.D. 40 MOTOR (Cont d) 157 00 07SMTP09 5.8 15SMTP05 6. 01 46 15SMTP05 6. 47 7 07SMTP05 9. 8 400 0SMTP05 6.5 50 MOTOR 5 7 800SMTP5 1.0 8 11 608SMTP5 8.1 608SMTP15 11.9 1 18 507SMTP5 7.9 507SMTP15 8.7 19 5 415SMTP5 7.1 415SMTP15 7.1 6 9 407SMTP5 6.4 407SMTP15 6.4 40 50 15SMTP5 6.4 15SMTP5 6.4 15SMTP15 6.4 15SMTP09 8.6 51 58 15SMTP5 6.4 15SMTP15 6.4 15SMTP09 8.6 59 80 07SMTP5 6.0 07SMTP15 6.0 07SMTP09 7.8 81 89 07SMTP15 6.0 07SMTP09 7.8 90 99 07SMTP15 6.0 07SMTP09 7.8 15SMTP05 0. 0 4 07SMTP15 6.0 07SMTP09 7.8 07SMTP05 9.0 5 07SMTP15 6.0 15SMTP09 5.6 07SMTP05 9.0 11 18 15SMTP09 5.6 07SMTP05 9.0 18 00 15SMTP09 5.6 15SMTP05 6. 01 40 15SMTP05 6. 41 400 07SMTP05 9.1 60 MOTOR 5 6 9 800SMTP5 1.0 14 608SMTP5 8.1 608SMTP15 11.4 15 507SMTP5 7.9 507SMTP15 8. 1 415SMTP5 7.1 415SMTP15 7.1 48 407SMTP5 6.4 407SMTP15 6.4 49 50 15SMTP5 6.4 15SMTP5 6.4 15SMTP15 6.4 15SMTP09 9.9 51 74 15SMTP5 6.4 15SMTP15 6.4 15SMTP09 9.9

SMTP SMTP/SMFP Selection Chart Class I Service (1.0 S.F.) RPM Reducer Minimum Sheave P.D. 60 MOTOR (Cont d) 75 80 07SMTP5 6.0 07SMTP15 6.0 07SMTP09 8.9 81 89 07SMTP15 6.0 07SMTP09 8.9 90 07SMTP15 6.0 07SMTP09 8.9 15SMTP05 0. 11 00 07SMTP09 8.9 07SMTP05 8.8 01 40 07SMTP05 8.8 41 400 15SMTP05 6.1 75 MOTOR 5 7 8 11 800SMTP5 1.0 1 18 608SMTP5 8.1 608SMTP15 11.9 19 8 507SMTP5 7.9 507SMTP15 8. 9 40 415SMTP5 7.1 415SMTP15 7.1 41 61 407SMTP5 6.4 407SMTP15 6.6 6 80 15SMTP5 6.4 15SMTP15 6.4 15SMTP09 1.0 81 89 15SMTP15 6.4 15SMTP09 1.0 90 15SMTP15 6.4 15SMTP09 1.0 407SMTP05 8.0 1 07SMTP15 6.0 07SMTP09 9.8 407SMTP05 8.0 14 07SMTP15 6.0 07SMTP09 9.8 15SMTP05 19.9 11 181 07SMTP09 9.8 15SMTP05 19.9 18 00 07SMTP09 9.8 07SMTP05 8.7 01 7 07SMTP05 8.7 8 400 15SMTP05 6.0 0 MOTOR 5 9 15 800SMTP5 1.0 16 4 608SMTP5 8.1 608SMTP15 1.7 5 8 507SMTP5 7.9 507SMTP15 9.9 9 54 415SMTP5 7.1 415SMTP15 7.1 55 80 407SMTP5 6.7 407SMTP15 6.7 81 87 407SMTP15 6.7 88 89 407SMTP15 6.7 15SMTP09 14. RPM Reducer Notes: Requires fan kit. Requires pump and cooler kit. Contact Application Engineering (1 800 66 09) for the selection of an enclosed gear drive. Minimum Sheave P.D. 0 MOTOR (Cont d) 90 95 407SMTP15 6.7 15SMTP09 14. 415SMTP05 40.5 96 6 15SMTP15 6.4 15SMTP09 14. 415SMTP05 40.5 7 117 15SMTP15 6.4 15SMTP09 14. 407SMTP05.7 118 15SMTP15 6.4 15SMTP09 14. 407SMTP05 0.4 11 155 15SMTP09 14. 407SMTP05 0.4 156 186 07SMTP09 9.6 407SMTP05 0.4 187 00 07SMTP09 9.6 15SMTP05 19.6 01 80 15SMTP05 19.6 81 400 07SMTP05 8.4 15 MOTOR 5 1 1 0 800SMTP5 1.0 1 1 608SMTP5 8. 608SMTP15 17. 51 507SMTP5 7.9 507SMTP15 11.7 5 74 415SMTP5 7.1 415SMTP15 7.1 75 80 407SMTP5 6.7 407SMTP15 6.7 81 11 407SMTP15 6.7 415SMTP05 40.5 1 407SMTP15 6.7 15SMTP09 14.0 415SMTP05 40.5 11 146 15SMTP09 14.0 415SMTP05 40.5 147 00 15SMTP09 14.0 407SMTP05 9.9 01 56 407SMTP05 9.9 57 94 15SMTP05 19. 95 400 07SMTP05 8. 150 MOTOR 5 15 16 4 800SMTP5 1.0 5 40 608SMTP5.5 608SMTP15.4 41 67 507SMTP5 7.9 507SMTP15 11.9 68 80 415SMTP5 7.1 415SMTP15 7.1 81 111 415SMTP15 7.1 11 415SMTP15 7.1 415SMTP05 41. 11 159 415SMTP05 41. 160 190 15SMTP09 1.6 415SMTP05 41. 191 00 15SMTP09 1.6 407SMTP05 9.4 01 4 407SMTP05 9.4 5 400 15SMTP05 19.0 RPM Reducer Minimum Sheave P.D. 00 MOTOR 5 0 1 5 800SMTP5 1.0 6 61 608SMTP5 11.5 608SMTP15 0.9 6 80 507SMTP5 11.5 507SMTP15 11.9 81 1 507SMTP15 11.9 415SMTP15 7.1 11 168 169 17 415SMTP05 40.4 18 400 407SMTP05 8.5 50 MOTOR 5 6 7 50 800SMTP5 1.0 51 80 608SMTP5.5 608SMTP15 19.1 81 84 608SMTP15 19.1 85 507SMTP15 11.9 11 400 415SMTP05 9.9 00 MOTOR 5 66 800SMTP5 1.0 67 80 608SMTP5.4 608SMTP15 17.9 81 1 608SMTP15 17.9 111 507SMTP15 11.8 11 0 0 400 415SMTP05 9.4 50 MOTOR 5 8 9 80 800SMTP5 1.0 81 84 85 608SMTP15 16.8 11 78 79 400 415SMTP05 9.0 400 MOTOR 5 44 45 80 800SMTP5 1.0 81 4 5 608SMTP15 15.8 11 400 450 MOTOR 5 50 51 80 800SMTP5 1.0 81 15 16 608SMTP15 15.1 11 400 500 MOTOR 5 56 57 80 800SMTP5 1.0 81 400 600 MOTOR 5 68 69 80 800SMTP5 1.0 81400 700 MOTOR 5 400 15

SMTP/SMFP Selection Chart Class II Service (1.4 S.F.) RPM Reducer Minimum Sheave P.D. 1/4 MOTOR 5 50 7SMTP5. 7SMTP5. 7SMTP15. 7SMTP09. 51 80 7SMTP5. 7SMTP15. 7SMTP09. 81 89 7SMTP15. 7SMTP09. 90 7SMTP15. 7SMTP09. 7SMTP05.8 11 00 7SMTP09. 7SMTP05.8 01 400 7SMTP05.7 1/ MOTOR 5 50 7SMTP5. 7SMTP5. 7SMTP15. 7SMTP09. 51 80 7SMTP5. 7SMTP15. 7SMTP09. 81 89 7SMTP15. 7SMTP09. 90 7SMTP15. 7SMTP09. 7SMTP05.8 11 00 7SMTP09. 7SMTP05.8 01 400 7SMTP05.8 1/ MOTOR 5 6 115SMTP5.4 115SMTP5.4 115SMTP15.4 115SMTP09.4 7 50 7SMTP5. 7SMTP5. 7SMTP15. 7SMTP09.4 51 80 7SMTP5. 7SMTP15. 7SMTP09.4 81 89 7SMTP15. 7SMTP09.4 90 7SMTP15. 7SMTP09.4 7SMTP05.8 11 00 7SMTP09.4 7SMTP05.8 01 400 7SMTP05.8 /4 MOTOR 5 7 0SMTP5.8 0SMTP5.8 0SMTP15.8 0SMTP09.8 RPM Reducer Minimum Sheave P.D. /4 MOTOR (Cont d) 8 115SMTP5.4 115SMTP5.4 115SMTP15.4 115SMTP09.4 11 50 7SMTP5. 7SMTP5. 7SMTP15. 7SMTP09. 51 80 7SMTP5. 7SMTP15. 7SMTP09. 81 89 7SMTP15. 7SMTP09. 90 7SMTP15. 7SMTP09. 7SMTP05.8 11 00 7SMTP09. 7SMTP05.8 01 400 7SMTP05.8 1 MOTOR 5 07SMTP5 4. 07SMTP5 4. 07SMTP15 4. 07SMTP09 4. 6 0SMTP5.7 0SMTP5.7 0SMTP15.7 0SMTP09.7 11 1 115SMTP5.4 115SMTP5.4 115SMTP15.4 115SMTP09.4 14 50 7SMTP5. 7SMTP5. 7SMTP15. 7SMTP09.4 51 80 7SMTP5. 7SMTP15. 7SMTP09.4 81 89 7SMTP15. 7SMTP09.4 90 7SMTP15. 7SMTP09.4 7SMTP05.8 11 00 7SMTP09.4 7SMTP05.8 01 400 7SMTP05.8 1 1/ MOTOR 5 15SMTP5 5.6 15SMTP5 5.6 15SMTP15 5.6 15SMTP09 5.6 6 8 07SMTP5 4. 07SMTP5 4. 07SMTP15 4. 07SMTP09 4. RPM Reducer Minimum Sheave P.D. 1 1/ MOTOR (Cont d) 9 15 0SMTP5.8 0SMTP5.8 0SMTP15.8 0SMTP09.8 16 1 115SMTP5.4 115SMTP5.4 115SMTP15.4 115SMTP09.4 50 7SMTP5. 7SMTP5. 7SMTP15. 7SMTP09. 51 80 7SMTP5. 7SMTP15. 7SMTP09. 81 89 7SMTP15. 7SMTP09. 90 7SMTP15. 7SMTP09. 7SMTP05.8 11 00 7SMTP09. 7SMTP05.8 01 400 7SMTP05.8 MOTOR 5 7 15SMTP5 5.6 15SMTP5 5.6 15SMTP15 5.6 15SMTP09 5.6 8 11 07SMTP5 4. 07SMTP5 4. 07SMTP15 4. 07SMTP09 4. 0SMTP5.8 0SMTP5.8 0SMTP15.8 0SMTP09.8 18 115SMTP5.4 115SMTP5.4 115SMTP15.4 115SMTP09.4 950 7SMTP5. 7SMTP5. 7SMTP15. 7SMTP09. 5180 7SMTP5. 7SMTP15. 7SMTP09. 8189 7SMTP15. 7SMTP09. 90 7SMTP15. 7SMTP09. 7SMTP05.8 10 7SMTP09. 7SMTP05.8 01400 7SMTP05.8 16

SMTP SMTP/SMFP Selection Chart Class II Service (1.4 S.F.) RPM Reducer Minimum Sheave P.D. MOTOR 56 07SMTP5 6.0 07SMTP5 6.0 07SMTP15 6.0 07SMTP09 6.0 711 15SMTP5 5.6 15SMTP5 5.6 15SMTP15 5.6 15SMTP09 5.6 118 07SMTP5 4. 07SMTP5 4. 07SMTP15 4. 07SMTP09 4. 191 0SMTP5.8 0SMTP5.8 0SMTP15.8 0SMTP09.8 44 115SMTP5.4 115SMTP5.4 115SMTP15.4 115SMTP09.4 4550 7SMTP5. 7SMTP5. 7SMTP15. 7SMTP09. 5180 7SMTP5. 7SMTP15. 7SMTP09. 8189 7SMTP15. 7SMTP09. 90 7SMTP15. 7SMTP09. 7SMTP05.8 10 7SMTP09. 7SMTP05.8 01400 7SMTP05.8 5 MOTOR 5 6 15SMTP5 6.4 15SMTP5 6.4 15SMTP15 6.4 15SMTP09 6.4 7 11 07SMTP5 6.0 07SMTP5 6.0 07SMTP15 6.0 07SMTP09 6.0 1 19 15SMTP5 5.6 15SMTP5 5.6 15SMTP15 5.6 15SMTP09 5.6 0 0 07SMTP5 4. 07SMTP5 4. 07SMTP15 4. 07SMTP09 4. 1 50 0SMTP5.8 0SMTP5.8 0SMTP15.8 0SMTP09.8 51 54 0SMTP5.8 0SMTP15.8 0SMTP09.8 RPM Reducer Minimum Sheave P.D. 5 MOTOR (Cont d) 55 77 115SMTP5.4 115SMTP15.4 115SMTP09.4 78 80 7SMTP5. 7SMTP15. 7SMTP09.0 81 89 7SMTP15. 7SMTP09.0 90 7SMTP15. 7SMTP09.0 115SMTP05 4.9 11 144 7SMTP09.0 115SMTP05 4.9 145 00 7SMTP09.0 7SMTP05.8 01 400 7SMTP05.8 7 1/ MOTOR 5 7 407SMTP5 6.4 407SMTP15 6.4 8 9 15SMTP5 6.4 15SMTP5 6.4 15SMTP15 6.4 15SMTP09 6.4 17 07SMTP5 6.0 07SMTP5 6.0 07SMTP15 6.0 07SMTP09 6.0 18 9 15SMTP5 5.6 15SMTP5 5.6 15SMTP15 5.6 15SMTP09 5.6 0 46 07SMTP5 4. 07SMTP5 4. 07SMTP15 4. 07SMTP09 4. 47 50 0SMTP5.8 0SMTP5.8 0SMTP15.8 0SMTP09.8 51 80 0SMTP5.8 0SMTP15.8 0SMTP09.8 81 8 0SMTP15.8 0SMTP09.8 8 89 115SMTP15.4 115SMTP09.4 90 96 115SMTP15.4 115SMTP09.4 0SMTP05 4. 97 119 115SMTP15.4 115SMTP09.4 115SMTP05 7.0 7SMTP15. 7SMTP09.0 115SMTP05 7.0 11 00 7SMTP09.0 115SMTP05 7.0 RPM Reducer Minimum Sheave P.D. 7 1/ MOTOR (Cont d) 01 61 115SMTP05 7.0 6 400 7SMTP05.4 MOTOR 5 6 415SMTP5 7.1 415SMTP15 7.1 7 407SMTP5 6.4 407SMTP15 6.4 11 1 15SMTP5 6.4 15SMTP5 6.4 15SMTP15 6.4 15SMTP09 6.4 14 07SMTP5 6.0 07SMTP5 6.0 07SMTP15 6.0 07SMTP09 6.0 4 9 15SMTP5 5.6 15SMTP5 5.6 15SMTP15 5.6 15SMTP09 5.6 40 50 07SMTP5 4. 07SMTP5 4. 07SMTP15 4. 07SMTP09 4. 51 71 07SMTP5 4. 07SMTP15 4. 07SMTP09 4. 7 80 0SMTP5.8 0SMTP15.8 0SMTP09.8 81 89 0SMTP15.8 0SMTP09.8 90 111 0SMTP15.8 0SMTP09.8 0SMTP05 4. 11 115SMTP15.4 115SMTP09.4 0SMTP05 4. 11 145 115SMTP09.4 0SMTP05 4. 146 175 115SMTP09.4 115SMTP05 6.9 176 00 7SMTP09.7 115SMTP05 6.9 01 400 115SMTP05 6.9 15 MOTOR 5 7 507SMTP5 7.9 507SMTP15 7.9 8 415SMTP5 7.1 415SMTP15 7.1 11 15 407SMTP5 6.4 407SMTP15 6.4 16 0 15SMTP5 6.4 15SMTP5 6.4 15SMTP15 6.4 15SMTP09 6.4 1 6 07SMTP5 6.0 07SMTP5 6.0 07SMTP15 6.0 07SMTP09 6.0 17

SMTP/SMFP Selection Chart Class II Service (1.4 S.F.) RPM Reducer Minimum Sheave P.D. 15 MOTOR (Cont d) 7 50 15SMTP5 5.6 15SMTP5 5.6 15SMTP15 5.6 15SMTP09 5.6 51 66 15SMTP5 5.6 15SMTP15 5.6 15SMTP09 5.6 67 80 07SMTP5 4. 07SMTP15 4. 07SMTP09 4. 81 89 07SMTP15 4. 07SMTP09 4. 90 97 07SMTP15 4. 07SMTP09 4. 15SMTP05 5.6 98 1 07SMTP15 4. 07SMTP09 4. 07SMTP05 6.9 1 0SMTP15.8 0SMTP09.8 0SMTP05 4.9 11 181 0SMTP09.8 0SMTP05 4.9 18 00 115SMTP09.4 0SMTP05 4.9 01 61 0SMTP05 4.9 6 400 115SMTP05 6.7 0 MOTOR 5 6 608SMTP5 8.1 608SMTP15 8.1 7 9 507SMTP5 7.9 507SMTP15 7.9 1 415SMTP5 7.1 415SMTP15 7.1 14 1 407SMTP5 6.4 407SMTP15 6.4 7 15SMTP5 6.4 15SMTP5 6.4 15SMTP15 6.4 15SMTP09 6.4 8 50 07SMTP5 6.0 07SMTP5 6.0 07SMTP15 6.0 07SMTP09 6.0 51 80 15SMTP5 5.6 15SMTP15 5.6 15SMTP09 5.6 81 89 15SMTP15 5.6 15SMTP09 5.6 90 96 15SMTP15 5.6 15SMTP09 5.6 15SMTP05 5.6 97 07SMTP15 4. 07SMTP09 4. 15SMTP05 5.6 11 147 07SMTP09 4. 15SMTP05 5.6 148 189 07SMTP09 4. 07SMTP05 6.8 RPM Reducer Minimum Sheave P.D. 0 MOTOR (Cont d) 190 00 0SMTP09.8 0SMTP05 4.8 01 96 0SMTP05 4.8 97 400 115SMTP05 6.5 5 MOTOR 5 6 7 608SMTP5 8.1 608SMTP15 8.1 8 1 507SMTP5 7.9 507SMTP15 7.9 1 17 415SMTP5 7.1 415SMTP15 7.1 18 7 407SMTP5 6.4 407SMTP15 6.4 8 5 15SMTP5 6.4 15SMTP5 6.4 15SMTP15 6.4 15SMTP09 6.4 6 50 07SMTP5 6.0 07SMTP5 6.0 07SMTP15 6.0 07SMTP09 6.0 51 6 07SMTP5 6.0 07SMTP15 6.0 07SMTP09 6.0 6 80 15SMTP5 5.6 15SMTP15 5.6 15SMTP09 5.6 81 89 15SMTP15 5.6 15SMTP09 5.6 90 7 15SMTP15 5.6 15SMTP09 5.6 07SMTP05 6.0 8 15SMTP15 5.6 15SMTP09 5.6 15SMTP05 5.6 11 00 07SMTP09 4. 15SMTP05 5.6 01 69 07SMTP05 6.7 70 400 0SMTP05 4.7 0 MOTOR 5 6 800SMTP5 1.0 7 9 608SMTP5 8.1 608SMTP15 8. 15 507SMTP5 7.9 507SMTP15 7.9 16 1 415SMTP5 7.1 415SMTP15 7.1 407SMTP5 6.4 407SMTP15 6.4 4 45 15SMTP5 6.4 15SMTP5 6.4 15SMTP15 6.4 15SMTP09 6.4 46 50 07SMTP5 6.0 07SMTP5 6.0 07SMTP15 6.0 07SMTP09 6.0 RPM Reducer Minimum Sheave P.D. 0 MOTOR (Cont d) 51 80 07SMTP5 6.0 07SMTP15 6.0 07SMTP09 6.0 81 89 07SMTP15 6.0 15SMTP09 5.6 90 15SMTP15 5.6 15SMTP09 5.6 07SMTP05 6.0 11 140 15SMTP09 5.6 07SMTP05 6.0 141 167 15SMTP09 5.6 15SMTP05 5.6 168 00 07SMTP09 4. 15SMTP05 5.6 01 64 15SMTP05 5.6 65 51 07SMTP05 6.6 5 400 0SMTP05 4.6 40 MOTOR 5 6 8 800SMTP5 1.0 9 1 608SMTP5 8.1 608SMTP15 8.5 14 0 507SMTP5 7.9 507SMTP15 7.9 1 9 415SMTP5 7.1 415SMTP15 7.1 0 45 407SMTP5 6.4 407SMTP15 6.4 46 50 15SMTP5 6.4 15SMTP5 6.4 15SMTP15 6.4 15SMTP09 6.7 51 70 15SMTP5 6.4 15SMTP15 6.4 15SMTP09 6.7 71 80 07SMTP5 6.0 07SMTP15 6.0 07SMTP09 6.0 81 89 07SMTP15 6.0 07SMTP09 6.0 90 117 07SMTP15 6.0 07SMTP09 6.0 15SMTP05 1.5 118 1 07SMTP15 6.0 07SMTP09 6.0 07SMTP05 6.4 1 15SMTP15 5.6 15SMTP09 5.6 07SMTP05 6.4 11 00 15SMTP09 5.6 07SMTP05 6.4 01 16 07SMTP05 6.4 17 400 15SMTP05 5.6 50 MOTOR 5 6 7 800SMTP5 1.0 11 16 608SMTP5 8.1 608SMTP15 8.6 17 6 507SMTP5 7.9 507SMTP15 7.9 Notes: Requires fan kit. Requires pump and cooler kit. Contact Application Engineering (1 800 66 09) for the selection of an enclosed gear drive. 18

SMTP SMTP/SMFP Selection Chart Class II Service (1.4 S.F.) RPM Reducer Minimum Sheave P.D. 50 MOTOR (Cont d) 7 7 415SMTP5 7.1 415SMTP15 7.1 8 57 407SMTP5 6.4 407SMTP15 6.4 58 80 15SMTP5 6.4 15SMTP15 6.4 15SMTP09 8.0 81 89 15SMTP15 6.4 15SMTP09 8.0 90 111 07SMTP15 6.0 07SMTP09 7. 07SMTP05 18.7 11 07SMTP15 6.0 07SMTP09 7. 15SMTP05 14.4 11 16 07SMTP09 7. 15SMTP05 14. 164 169 07SMTP09 7. 07SMTP05 6. 170 00 15SMTP09 5.6 07SMTP05 6. 01 04 07SMTP05 6. 05 400 15SMTP05 5.6 60 MOTOR 5 8 9 1 800SMTP5 1.0 14 0 608SMTP5 8.1 608SMTP15 8. 1 507SMTP5 7.9 507SMTP15 7.9 44 415SMTP5 7.1 415SMTP15 7.1 45 70 407SMTP5 6.4 407SMTP15 6.4 71 80 15SMTP5 6.4 15SMTP15 6.4 15SMTP09 9.6 81 89 15SMTP15 6.4 15SMTP09 9.6 90 15SMTP15 6.4 15SMTP09 9.6 407SMTP05.0 11 07SMTP15 6.0 07SMTP09 7.0 407SMTP05.0 11 144 07SMTP09 7.0 407SMTP05.0 145 00 07SMTP09 7.0 15SMTP05 14. 01 15 15SMTP05 14. 16 400 07SMTP05 6.1 75 MOTOR 5 11 16 800SMTP5 1.0 17 6 608SMTP5 8.1 608SMTP15 9.6 7 41 507SMTP5 7.9 507SMTP15 7.9 RPM Reducer Minimum Sheave P.D. 75 MOTOR (Cont d) 4 58 415SMTP5 7.1 415SMTP15 7.1 59 80 407SMTP5 6.4 407SMTP15 6.4 81 89 407SMTP15 6.4 90 94 407SMTP15 6.4 415SMTP05 4. 95 407SMTP15 6.4 15SMTP09.1 415SMTP05 4. 15 15SMTP15 6.4 15SMTP09.1 415SMTP05 4. 16 15SMTP15 6.4 15SMTP09.1 407SMTP05 1.8 11 166 15SMTP09.1 407SMTP05 1.8 167 00 07SMTP09 6.8 407SMTP05 1.8 01 01 15SMTP05 1.9 0 400 07SMTP05 6.0 0 MOTOR 5 14 15 800SMTP5 1.0 7 608SMTP5 8.1 608SMTP15 14.6 8 61 507SMTP5 7.9 507SMTP15 8.4 6 80 415SMTP5 7.1 415SMTP15 7.1 81 89 415SMTP15 7.1 90 407SMTP15 6.4 415SMTP05 9.6 11 14 415SMTP05 9.6 144 17 15SMTP09 9.8 415SMTP05 9.6 17 190 15SMTP09 9.8 407SMTP05 1.1 191 00 15SMTP09 9.8 407SMTP05 1.1 01 0 407SMTP05 1.1 0 400 15SMTP05 1.7 15 MOTOR 5 18 19 9 800SMTP5 1.0 0 50 608SMTP5 9.8 608SMTP15 15.0 51 80 507SMTP5 7.9 507SMTP15 8.5 81 11 415SMTP15 7.1 1 407SMTP15 6.4 19 199 415SMTP05 9. 00 6 7 400 407SMTP05 0.7 150 MOTOR 5 0 800SMTP5 1.0 9 66 608SMTP5 8.1 608SMTP15 14.7 RPM Reducer Minimum Sheave P.D. 150 MOTOR (Cont'd) 67 80 507SMTP5 7.9 507SMTP15 8.4 81 8 507SMTP15 8.4 9 415SMTP15 7.1 11 180 181 40 415SMTP05 8.9 41 400 407SMTP05 0. 00 MOTOR 5 0 1 59 800SMTP5 1.0 60 80 608SMTP5 8.1 608SMTP15 1. 81 99 608SMTP15 1. 0 507SMTP15 8.5 11 7 74 400 415SMTP05 8. 50 MOTOR 5 8 9 80 800SMTP5 1.0 81 84 85 608SMTP15 1.0 11 78 79 400 415SMTP05 7.9 00 MOTOR 5 46 47 80 800SMTP5 1.0 81 11 11 608SMTP15 11.1 11 400 50 MOTOR 5 55 56 80 800SMTP5 1.0 81 400 400 MOTOR 5 6 64 80 800SMTP5 1.0 81 400 450 MOTOR 5 7 7 80 800SMTP5 1.0 81 400 500 MOTOR 5 400 Notes: Requires fan kit. Requires pump and cooler kit. Contact Application Engineering (1 800 66 09) for the selection of an enclosed gear drive. 19

SMTP/SMFP Selection Chart Class III Service (.0 S.F.) RPM Reducer Minimum Sheave P.D. 1/4 MOTOR 5 50 7SMTP5. 7SMTP5. 7SMTP15. 7SMTP09.4 51 80 7SMTP5. 7SMTP15. 7SMTP09.4 81 89 7SMTP15. 7SMTP09.4 90 7SMTP15. 7SMTP09.4 7SMTP05. 11 00 7SMTP09.4 7SMTP05. 01 400 7SMTP05. 1/ MOTOR 5 6 115SMTP5.4 115SMTP5.4 115SMTP15.4 115SMTP09.4 7 50 7SMTP5. 7SMTP5. 7SMTP15. 7SMTP09. 51 80 7SMTP5. 7SMTP15. 7SMTP09. 81 89 7SMTP15. 7SMTP09. 90 7SMTP15. 7SMTP09. 7SMTP05. 11 00 7SMTP09. 7SMTP05. 01 400 7SMTP05. 1/ MOTOR 5 6 0SMTP5.8 0SMTP5.8 0SMTP15.8 0SMTP09.8 7 9 115SMTP5.4 115SMTP5.4 115SMTP15.4 115SMTP09.4 50 7SMTP5. 7SMTP5. 7SMTP15. 7SMTP09.4 51 80 7SMTP5. 7SMTP15. 7SMTP09.4 81 89 7SMTP15. 7SMTP09.4 90 7SMTP15. 7SMTP09.4 7SMTP05. 11 00 7SMTP09.4 7SMTP05. 01 400 7SMTP05. RPM Reducer Minimum Sheave P.D. /4 MOTOR 5 07SMTP5 4. 07SMTP5 4. 07SMTP15 4. 07SMTP09 4. 6 0SMTP5.8 0SMTP5.8 0SMTP15.8 0SMTP09.8 11 14 115SMTP5.4 115SMTP5.4 115SMTP15.4 115SMTP09.4 15 50 7SMTP5. 7SMTP5. 7SMTP15. 7SMTP09.4 51 80 7SMTP5. 7SMTP15. 7SMTP09.4 81 89 7SMTP15. 7SMTP09.4 90 7SMTP15. 7SMTP09.4 7SMTP05. 11 00 7SMTP09.4 7SMTP05. 01 400 7SMTP05. 1 MOTOR 5 8 07SMTP5 4. 07SMTP5 4. 07SMTP15 4. 07SMTP09 4. 9 14 0SMTP5.8 0SMTP5.8 0SMTP15.8 0SMTP09.8 15 0 115SMTP5.4 115SMTP5.4 115SMTP15.4 115SMTP09.4 1 50 7SMTP5. 7SMTP5. 7SMTP15. 7SMTP09. 51 80 7SMTP5. 7SMTP15. 7SMTP09. 81 89 7SMTP15. 7SMTP09. 90 7SMTP15. 7SMTP09. 7SMTP05. 11 00 7SMTP09. 7SMTP05. 01 400 7SMTP05. RPM Reducer Minimum Sheave P.D. 1 1/ MOTOR 5 7 15SMTP5 5.6 15SMTP5 5.6 15SMTP15 5.6 15SMTP09 5.6 8 1 07SMTP5 4. 07SMTP5 4. 07SMTP15 4. 07SMTP09 4. 1 0SMTP5.8 0SMTP5.8 0SMTP15.8 0SMTP09.8 1 115SMTP5.4 115SMTP5.4 115SMTP15.4 115SMTP09.4 50 7SMTP5. 7SMTP5. 7SMTP15. 7SMTP09. 51 80 7SMTP5. 7SMTP15. 7SMTP09. 81 89 7SMTP15. 7SMTP09. 90 7SMTP15. 7SMTP09. 7SMTP05. 11 00 7SMTP09. 7SMTP05. 01 400 7SMTP05. MOTOR 5 6 07SMTP5 6.0 07SMTP5 6.0 07SMTP15 6.0 07SMTP09 6.0 7 15SMTP5 5.6 15SMTP5 5.6 15SMTP15 5.6 15SMTP09 5.6 11 17 07SMTP5 4. 07SMTP5 4. 07SMTP15 4. 07SMTP09 4. 18 0 0SMTP5.8 0SMTP5.8 0SMTP15.8 0SMTP09.8 1 4 115SMTP5.4 115SMTP5.4 115SMTP15.4 115SMTP09.4 4 50 7SMTP5. 7SMTP5. 7SMTP15. 7SMTP09. 51 80 7SMTP5. 7SMTP15. 7SMTP09. 0

SMTP SMTP/SMFP Selection Chart Class III Service (.0 S.F.) RPM Reducer Minimum Sheave P.D. MOTOR (Cont d) 81 89 7SMTP15. 7SMTP09. 90 7SMTP15. 7SMTP09. 7SMTP05. 11 00 7SMTP09. 7SMTP05. 01 400 7SMTP05. MOTOR 5 15SMTP5 6.4 15SMTP5 6.4 15SMTP15 6.4 15SMTP09 6.4 6 9 07SMTP5 6.0 07SMTP5 6.0 07SMTP15 6.0 07SMTP09 6.0 16 15SMTP5 5.6 15SMTP5 5.6 15SMTP15 5.6 15SMTP09 5.6 17 6 07SMTP5 4. 07SMTP5 4. 07SMTP15 4. 07SMTP09 4. 7 46 0SMTP5.8 0SMTP5.8 0SMTP15.8 0SMTP09.8 47 50 115SMTP5.4 115SMTP5.4 115SMTP15.4 115SMTP09.4 51 65 115SMTP5.4 115SMTP15.4 115SMTP09.4 66 80 7SMTP5. 7SMTP15. 7SMTP09. 81 89 7SMTP15. 7SMTP09. 90 115 7SMTP15. 7SMTP09. 115SMTP05 4.9 116 7SMTP15. 7SMTP09. 7SMTP05. 11 00 7SMTP09. 7SMTP05. 01 400 7SMTP05. 5 MOTOR 5 7 407SMTP5 6.4 407SMTP15 6.4 8 9 15SMTP5 6.4 15SMTP5 6.4 15SMTP15 6.4 15SMTP09 6.4 RPM Reducer Minimum Sheave P.D. 5 MOTOR (Cont d) 16 07SMTP5 6.0 07SMTP5 6.0 07SMTP15 6.0 07SMTP09 6.0 17 7 15SMTP5 5.6 15SMTP5 5.6 15SMTP15 5.6 15SMTP09 5.6 8 44 07SMTP5 4. 07SMTP5 4. 07SMTP15 4. 07SMTP09 4. 45 50 0SMTP5.8 0SMTP5.8 0SMTP15.8 0SMTP09.8 51 80 0SMTP5.8 0SMTP15.8 0SMTP09.8 81 89 115SMTP15.4 115SMTP09.4 90 11 115SMTP15.4 115SMTP09.4 115SMTP05 4.9 114 7SMTP15. 7SMTP09. 115SMTP05 4.9 11 00 7SMTP09. 115SMTP05 4.9 01 44 115SMTP05 4.9 45 400 7SMTP05. 7 1/ MOTOR 5 6 415SMTP5 7.1 415SMTP15 7.1 7 11 407SMTP5 6.4 407SMTP15 6.4 1 14 15SMTP5 6.4 15SMTP5 6.4 15SMTP15 6.4 15SMTP09 6.4 15 5 07SMTP5 6.0 07SMTP5 6.0 07SMTP15 6.0 07SMTP09 6.0 6 4 15SMTP5 5.6 15SMTP5 5.6 15SMTP15 5.6 15SMTP09 5.6 4 50 07SMTP5 4. 07SMTP5 4. 07SMTP15 4. 07SMTP09 4. 51 80 07SMTP5 4. 07SMTP15 4. 07SMTP09 4. 81 89 0SMTP15.8 0SMTP09.8 RPM Reducer Minimum Sheave P.D. 7 1/ MOTOR (Cont d) 90 0SMTP15.8 0SMTP09.8 0SMTP05.8 11 115SMTP15.4 115SMTP09.4 0SMTP05.8 11 161 115SMTP09.4 0SMTP05.8 16 194 115SMTP09.4 115SMTP05 4.8 195 00 7SMTP09. 115SMTP05 4.8 01 400 115SMTP05 4.8 MOTOR 5 6 507SMTP5 7.9 507SMTP15 7.9 7 9 415SMTP5 7.1 415SMTP15 7.1 14 407SMTP5 6.4 407SMTP15 6.4 15 19 15SMTP5 6.4 15SMTP5 6.4 15SMTP15 6.4 15SMTP09 6.4 0 4 07SMTP5 6.0 07SMTP5 6.0 07SMTP15 6.0 07SMTP09 6.0 5 50 15SMTP5 5.6 15SMTP5 5.6 15SMTP15 5.6 15SMTP09 5.6 51 61 15SMTP5 5.6 15SMTP15 5.6 15SMTP09 5.6 61 80 07SMTP5 4. 07SMTP15 4. 07SMTP09 4. 81 89 07SMTP15 4. 07SMTP09 4. 90 119 07SMTP15 4. 07SMTP09 4. 07SMTP05 4.9 0SMTP15.8 0SMTP09.8 11 168 0SMTP09.8 0SMTP05.8 169 00 115SMTP09.4 0SMTP05.8 01 44 0SMTP05.8 45 400 115SMTP05 4.7 15 MOTOR 5 6 608SMTP5 8.1 608SMTP15 8.1 7 507SMTP5 7.9 507SMTP15 7.9 11 15 415SMTP5 7.1 415SMTP15 7.1 1

SMTP/SMFP Selection Chart Class III Service (.0 S.F.) RPM Reducer Minimum Sheave P.D. 15 MOTOR (Cont d) 16 407SMTP5 6.4 407SMTP15 6.4 4 0 15SMTP5 6.4 15SMTP5 6.4 15SMTP15 6.4 15SMTP09 6.4 1 50 07SMTP5 6.0 07SMTP5 6.0 07SMTP15 6.0 07SMTP09 6.0 51 80 15SMTP5 5.6 15SMTP15 5.6 15SMTP09 5.6 81 89 15SMTP15 5.6 15SMTP09 5.6 90 5 15SMTP15 5.6 15SMTP09 5.6 15SMTP05 5.6 6 07SMTP15 4. 07SMTP09 4. 15SMTP05 5.6 11 16 07SMTP09 4. 15SMTP05 5.6 16 00 07SMTP09 4. 07SMTP05 4.8 01 15 07SMTP05 4.8 16 400 0SMTP05.8 0 MOTOR 5 800SMTP5 1.0 6 9 608SMTP5 8.1 608SMTP15 8.1 14 507SMTP5 7.9 507SMTP15 7.9 15 9 415SMTP5 7.1 415SMTP15 7.1 1 1 407SMTP5 6.4 407SMTP15 6.4 4 15SMTP5 6.4 15SMTP5 6.4 15SMTP15 6.4 15SMTP09 6.4 4 50 07SMTP5 6.0 07SMTP5 6.0 07SMTP15 6.0 07SMTP09 6.0 51 80 07SMTP5 6.0 07SMTP15 6.0 07SMTP09 6.0 81 89 15SMTP15 5.6 15SMTP09 5.6 90 15SMTP15 5.6 15SMTP09 5.6 07SMTP05 6.0 11 156 15SMTP09 5.6 15SMTP05 5.6 157 00 07SMTP09 4. 15SMTP05 5.6 01 46 15SMTP05 5.6 RPM Reducer Minimum Sheave P.D. 0 MOTOR (Cont d) 47 7 07SMTP05 4.6 8 400 0SMTP05.8 5 MOTOR 5 7 800SMTP5 1.0 8 11 608SMTP5 8.1 608SMTP15 8.1 1 18 507SMTP5 7.9 507SMTP15 7.9 19 5 415SMTP5 7.1 415SMTP15 7.1 6 9 407SMTP5 6.4 407SMTP15 6.4 40 50 15SMTP5 6.4 15SMTP5 6.4 15SMTP15 6.4 15SMTP09 6.4 51 59 15SMTP5 6.4 15SMTP15 6.4 15SMTP09 6.4 60 80 07SMTP5 6.0 07SMTP15 6.0 07SMTP09 6.0 81 89 07SMTP15 6.0 07SMTP09 6.0 90 99 07SMTP15 6.0 07SMTP09 6.0 15SMTP05.1 0 1 07SMTP15 6.0 07SMTP09 6.0 07SMTP05 6.0 111 15SMTP15 5.6 15SMTP09 5.6 07SMTP05 6.0 11 18 15SMTP09 5.6 07SMTP05 6.0 18 00 15SMTP09 5.6 15SMTP05 5.6 01 40 15SMTP05 5.6 41 400 07SMTP05 4.6 0 MOTOR 6 9 800SMTP5 1.0 14 608SMTP5 8.1 608SMTP15 8.1 15 507SMTP5 7.9 507SMTP15 7.9 1 415SMTP5 7.1 415SMTP15 7.1 48 407SMTP5 6.4 407SMTP15 6.4 49 50 15SMTP5 6.4 15SMTP5 6.4 15SMTP15 6.4 15SMTP09 6.4 51 80 15SMTP5 6.4 15SMTP15 6.4 15SMTP09 6.4 81 89 07SMTP15 6.0 07SMTP09 6.0 RPM Reducer Minimum Sheave P.D. 0 MOTOR (Cont d) 90 07SMTP15 6.0 07SMTP09 6.0 15SMTP05.1 11 00 15SMTP09 5.6 07SMTP05 6.0 01 40 07SMTP05 6.0 41 400 15SMTP05 5.6 40 MOTOR 5 7 8 1 800SMTP5 1.0 1 19 608SMTP5 8.1 608SMTP15 8.1 0 0 507SMTP5 7.9 507SMTP15 7.9 1 4 415SMTP5 7.1 415SMTP15 7.1 4 69 407SMTP5 6.4 407SMTP15 6.4 70 80 15SMTP5 6.4 15SMTP15 6.4 15SMTP09 6.4 81 89 15SMTP15 6.4 15SMTP09 6.4 90 11 15SMTP15 6.4 15SMTP09 6.4 407SMTP05 14.9 114 07SMTP15 6.0 07SMTP09 6.0 407SMTP05 14.9 11 00 07SMTP09 6.0 15SMTP05 9.9 01 7 07SMTP05 6.0 7 400 15SMTP05 5.6 50 MOTOR 5 9 15 800SMTP5 1.0 16 4 608SMTP5 8.1 608SMTP15 8.1 5 8 507SMTP5 7.9 507SMTP15 7.9 9 54 415SMTP5 7.1 415SMTP15 7.1 55 80 407SMTP5 6.4 407SMTP15 6.4 81 89 407SMTP15 6.4 90 95 407SMTP15 6.4 15SMTP09 7.1 415SMTP05 19.5 96 6 15SMTP15 6.4 15SMTP09 7. 415SMTP05 19.5 7 15SMTP15 6.4 15SMTP09 7. 407SMTP05 15. 11 155 15SMTP09 7. 407SMTP05 15. 156 186 07SMTP09 6.0 407SMTP05 15. Notes: Requires fan kit. Requires pump and cooler kit. Contact Application Engineering (1 800 66 09) for the selection of an enclosed gear drive.

SMTP SMTP/SMFP Selection Chart Class III Service (.0 S.F.) RPM Reducer Minimum Sheave P.D. 50 MOTOR (Cont d) 187 00 07SMTP09 6.0 15SMTP05 9.8 01 80 15SMTP05 9.8 81 400 07SMTP05 6.0 60 MOTOR 5 1 1 19 800SMTP5 1.0 0 0 608SMTP5 8.1 608SMTP15 8.1 1 48 507SMTP5 7.9 507SMTP15 7.9 49 70 415SMTP5 7.1 415SMTP15 7.1 71 80 407SMTP5 6.4 407SMTP15 6.4 81 89 407SMTP15 6.4 90 114 407SMTP15 6.4 415SMTP05 19.5 115 1 407SMTP15 6.4 15SMTP09 7.0 415SMTP05 19.5 14 15SMTP15 6.4 15SMTP09 7.0 415SMTP05 19.5 11 15 15SMTP09 7.0 407SMTP05 15.0 15 00 15SMTP09 7.0 407SMTP05 15.0 01 4 407SMTP05 15.0 4 70 15SMTP05 9.7 71 400 07SMTP05 6.0 75 MOTOR 5 15 16 4 800SMTP5 1.0 5 40 608SMTP5 8.1 608SMTP15 11.7 41 67 507SMTP5 7.9 507SMTP15 7.9 68 80 415SMTP5 7.1 415SMTP15 7.1 81 89 415SMTP15 7.1 90 97 415SMTP15 7.1 415SMTP05 0.7 98 407SMTP15 6.4 11 159 415SMTP05 0.7 160 190 15SMTP09 6.8 191 00 15SMTP09 6.8 407SMTP05 14.7 01 4 407SMTP05 14.7 5 400 15SMTP05 9.5 0 MOTOR 5 0 1 5 800SMTP5 1.0 6 61 608SMTP5 8.1 608SMTP15.5 6 80 507SMTP5 7.9 507SMTP15 7.9 81 1 507SMTP15 7.9 415SMTP15 7.1 RPM Reducer Minimum Sheave P.D. 0 MOTOR (Cont d) 11 168 169 86 415SMTP05 0. 87 400 407SMTP05 14. 15 MOTOR 5 6 7 50 800SMTP5 1.0 51 80 608SMTP5 8.1 608SMTP15 9.6 81 84 608SMTP15 9.6 85 507SMTP15 7.9 11 400 415SMTP05 0.1 150 MOTOR 5 66 800SMTP5 1.0 67 80 608SMTP5 8.1 608SMTP15 9.0 81 1 608SMTP15 9.0 111 507SMTP15 7.9 11 0 0 400 415SMTP05 19.7 00 MOTOR 5 44 45 80 800SMTP5 1.0 81 4 5 608SMTP15 8.1 11 400 50 MOTOR 5 56 57 80 800SMTP5 1.0 81 400 00 MOTOR 5 68 69 80 800SMTP5 1.0 81 400 50 MOTOR 5 400 Notes: Requires fan kit. Requires pump and cooler kit. Contact Application Engineering (1 800 66 09) for the selection of an enclosed gear drive.

Shaft Mount Reducers SMTP TorqTaper Plus Unit s 715 C A O L K J P M R P1 D Ø Ø1 F E MC Key U1 T S W N G Y 90 AA Reversible single bushing system mounted on the back side. PF Q WF RF SF TF olt size M L O P P1 Reversible single bushing system mounted on the front side. MC Part Number Explanation bore in 1/16" increments (15 = 15/16" output bore) Shaft mount TorqTaper Plus Nominal ratio (5:1) 4 15 SM TP 5

SMTP Shaft Mount Reducers SMTP TorqTaper Plus Unit s 715 PART DIMENSIONS IN INCES NO. A C D E F G 1 J 7SMTP 9.76 1.07 4.88 4.88 7.19.07 7.75.5 0.6 115SMTP 11 14.08 5.5 5.5 8.58 11.78 8.69 4.1.5 0.75 0SMTP 1.88 16.16 6.44 6.44 9.7 1.66.8 4.5.75 0.87 07SMTP 14.5 18.47 7.5 7.5 11. 15.7 11.76 4.88 4.5 1.01 15SMTP 16.5 0.88 8.1 8.1 1.76 18.07 1.44 5.1 4.75 1.07 07SMTP 19.04 4.7 9.5 9.5 14.85 1 15.67 6.44 5.69 1.5 15SMTP 19.9 6.5 9.95 9.95 16.4.0 16.57 7.1 6.7 1.5 PART DIMENSIONS IN INCES NO. K L M M MC N O O P P1 7SMTP 5.5 7.89.18.61 1.75 4.08 4.5 4.1 0.9 1.84 115SMTP 5.99 8.6.4.77 1.88 4.4 4.48 4.45 0.9 1.8 0SMTP 7.07 9.4 4.4.84 1.88 5.1 5.01 4.99 0.89 1.8 07SMTP 7.9 9.75 4..65 1.88 5.1 5.14 5.19 0.89 1.86 15SMTP 8.4.85 4.85 4.8 1.88 5.87 5.69 5.74 1.0 1.96 07SMTP 9.7 1.57 6.09 5.47.5 7.45 6.58 6.61 1.6.75 15SMTP.51 14.5 6.59 5.96.75 8. 7.51 7.61 1.7.5 PART NO. DIMENSIONS IN INCES PF Q R RF S SF T TF U1 7SMTP 1.14 4.4 1.18 0.6.77.50.95.8 0.75 7.88 115SMTP 1.14 4.51 1.5 0.6 4.6.50 4.56.8 1.1 9.14 0SMTP 1. 5.04 1.48 0.4 5.6.50 5.46.50 1.5.94 07SMTP 1.51 5.57 1.6 0.48 6.08.00 6.9 4.5 1.44 1.68 15SMTP 1.51 6.4.1 0.48 7.01.00 7. 4.5 1.87 14.19 07SMTP 1.81 6.79.5 0.61 7.78 4.00 8. 5.8.00 17.00 15SMTP. 8.05.6 0.7 8.5 4.75 8.9 6.50.1 18.1 W PART NO. DIMENSIONS IN INCES M. OUTPUT ORE WF Y AA OLT WT. LS KEY SIZE MIN. M. 7SMTP 1.44.7 4.00 0.00 /8.188 x.188 x.88 1 7/16 5 115SMTP 1.44.1 4.00 0.00 /8.50 x.50 x.75 1 15/16 75 0SMTP 1.7.64 4.00 0.00 /8.50 x.50 x.88 /16 11 07SMTP.19 4.16 7.00.00 7/16.75 x.75 x.75 7/16 155 15SMTP.19 4.65 7.00.00 7/16.500 x.500 x.75 15/16 6 07SMTP.78 5.58 9.00 5.00 1/.500 x.500 x 6.50 7/16 67 15SMTP.6 6. 9.50 5.50 5/8.500 x.500 x 7.50 15/16 480 Complete part number by adding ratio symbol, for example, 7SMTP05. Note 05 is symbol for 5:1 nominal ratio: see page 9 for exact ratios and ratio symbols. Dimension MC is minimum clearance for bushing removal. Order bushings from pages 64 thru 66 for shaft size required. 5

Shaft Mount Reducers SMTP TorqTaper Plus Unit s 407 800 C A O L K J M P P1 R D F E Ø MC Ø1 N Key ØU1 T S W G 90 PF Q WF RF SF TF AA Y olt size Part Dimensions in Inches No. A C D E F G 1 J K L M N O P P1 PF Q R RF 407SMTP 1.69 7.80.85.85 16.96 4.48 18.7 7.69 7.00 1.8.1 1.88 5.50 6.70 7.55 1.0.00. 8.5.1 0.7 415SMTP 5.04 1.80 1.5 1.5 19.8 8.01 1.5 9.44 7.88 1.6 1.6 16.78 8.00 9. 9.18 1..5.9 9.4.6 1.17 507SMTP 8.16 5.75 14.08 14.08 1.67 1.96 4.7 9.88 8.50 1.6 1.1 17.80 8.00 9.7 9.81 1.7.50.9 9.96 4.19 1.17 608SMTP 0. 9.58 15.11 15.11 4.47 5.78 6.4 11.56.94 1.88 16.74 1.96 8.00 9.51 1.09 1.51.75.5 1.50 4.5 1.6 800SMTP 6.56 46.9 18.8 18.8 8.65 41. 0.84 14.50 1.75.8 18.78 4.40.81 1.75 1.99 1.94 4.75 4.5 1.57 4.88 1.6 Part No. Part Number Explanation Dimensions in Inches AA olt S SF T TF U1 W WF Y Min. Max. Key Max. ore 407SMTP 9.4 4.75 9.75 6.50.1 19.7.6.56 9.50 5.50 5/8 1/ Sq. x 6.00 Key 4 7/16.75 609 415SMTP.9 7.00 11.00 8.75.7 1.79 4.8 7.16 8.00 4.00 /4 5/8 Sq. x 8.8 Key 4 15/16.5 957 507SMTP 11.78 7.00 1.50 8.75.6.75 4.8.6 8.00 4.00 /4 5/8 Sq. x 8.8 Key 57/16.75 117 608SMTP 1.60 7.00 14.5 9.5.69 6.05 4.96 11.71 8.00 4.00 /4 5/8 Sq. x 8.75 Key 6 1/ 4.5 191 800SMTP 15.4 9.00 16.00 11.88.94 1.6 5.75.6 1.00 7.00 7/8 /4 Sq. x 1.00 Key 8 4.50 894 MC Wt. Lbs. 407 SM TP 5 bore in 1/16" increments (407 = 4 7/16" output bore) Shaft mount TorqTaper Plus bushing Nominal ratio (5:1) arrier Seal Complete part number by adding ratio symbol, for example, 407SMTP05. 6

SMTP Shaft Mount Reducers SMFP Finished ore s 715 L M A K C O P R D F E N Key U1 T S W G Y 90 PF RF WF Q SF TF olt AA Part Number Explanation bore in 1/16" increments (15 = 15/16" output bore) Shaft mount Finished bore Nominal ratio (15:1) Note: SMFP units are madetoorder. Contact Emerson for delivery. 15 SM FP 15 PART NO. DIMENSIONS IN INCES OUTPUT ORE* A C D E F G J K L M N O DIA. KEYWAY 7SMFP 9.76 1.07 4.88 4.88 7.19.07 7.75.00 0.6 5.5 6.5.58 4.08.6 1.475.75 x.15 115SMFP 11.00 14.08 5.50 5.50 8.58 11.78 8.69.6 0.75 5.99 7.1.67 4.4.57 1.975.500 x.15 0SMFP 1.88 16.16 6.44 6.44 9.7 1.66.8.88 0.87 7.07 8.45 4.6 5.1 4..1875.500 x.187 07SMFP 14.50 18.47 7.5 7.5 11. 15.7 11.76.5 1.01 7.9 8.77 4.4 5.1 4.9.475.65 x.187 15SMFP 16.5 0.88 8.1 8.1 1.76 18.07 1.44.88 1.07 8.4.5 4.86 5.87 5.1.975.750 x.50 07SMFP 19.04 4.7 9.5 9.5 14.85 1.00 15.67 5.00 1.5 9.7 11.70 6.4 7.45 5.85.475.875 x.50 15SMFP 19.90 6.5 9.95 9.95 16.40.0 16.57 5.8 1.5.51 1.00 7.08 8. 6.50.975 1.000 x.50 PART DIMENSIONS IN INCES NO. OLT AA INPUT WT. P PF a R RF S SF T TF U1 W WF Y SIZE MIN. M. KEY LS. 7SMFP 0.50 1.14 4.4 1.18 0.6.77.50.95.8 0.75 7.88 1.44.7 /8 4 0.188 x.188 x.88 5 115SMFP 0.57 1.14 4.51 1.5 0.6 4.6.50 4.56.8 1.1 9.14 1.44.1 /8 4 0.50 x.50 x.75 75 0SMFP 0.69 1. 5.04 1.48 0.4 5.6.50 5.46.50 1.5.94 1.7.64 /8 4 0.50 x.50 x.88 11 07SMFP 0.69 1.51 5.57 1.6 0.48 6.08.00 6.9 4.5 1.44 1.68.19 4.16 7/16 7.75 x.75 x.75 155 15SMFP 1.01 1.51 6.4.1 0.48 7.01.00 7. 4.5 1.88 14.19.19 4.65 7/16 7.500 x.500 x.75 6 07SMFP 1. 1.81 6.79.5 0.61 7.78 4.00 8. 5.8.00 17.00.78 5.58 1/ 9 5.500 x.500 x 6.50 65 15SMFP 1.5. 8.05.8 0.7 8.5 4.75 8.9 6.50.1 18.1.8 6.0 5/8 9.5 55.500 x.500 x 7.50 477 Complete part number by adding ratio symbol, for example, 7SMFP05. Note 05 is symbol for 5:1 nominal ratio: see page 9 for exact ratios and ratio symbols. * If smaller shaft than the output bore is used, order bushing from page Accessories Section. 7

Application Inspired... ydraulically 8

MTP rowning ydraulic TorqTaper Plus Shaft Mount Reducers With over 5 years in developing innovative solutions for industries, Emerson engineers designed the newest member of the TorqTaper Plus family. The hydraulic TorqTaper Plus is appropriate for applications where fluid power is required. For applications where electric motors are not available, such as portable equipment Compatible with many hydraulic motors currently used in similar applications standard SAE mounting patterns Can be configured with screw conveyor components or as a shaft mounted reducer Patented mounting system, barrier seal system and increased ratings Replaces all popular hydraulic shaft mounted reducers Available with involute or straight sided input splines 9

Selection and Ordering Information Example No. 1 Units 7 15 ydraulic Shaft Mounts A hydraulic shaft mount reducer is required for a portable aggregate conveyor which can be loaded and operated 16 to 4 hours per day at 0. The conveyor requires hp. The reducer will be mounted on the conveyor drive pulley shaft, which is /16" diameter. 1. Determine the Load Classification From the AGMA Application Classification Numbers section, note the AGMA Class Number is II for a uniformly loaded or fed conveyor operating over hours per day.. Determine the Speed Reducer Required From the ydraulic Reducer Selection Chart section, there are four tables for selecting hydraulic shaft mounts for Class II Service. Locate the 0 row, if available, in each table. Read across the row to find a column with a rating of hp or greater. Read up the column to determine the basic reducer size that corresponds to the design hp. For this application, a 0MTP15 1T SAE, 0MTP5 9T SAEA, 0MTP05 6 SAEA or a 0MTP5 6 SAEA may be used. Select the reducer based upon hydraulic motor characteristics, such as spline dimensions and flow rates. (Note: ydraulic motors are not included with the reducer.) For this example, select 0MTP15 1T SAE. A 0TP0 bushing is required to mount any of the three reducers to the /16" driven shaft. A 0TAP torque arm kit is required to restrain the gearbox in operation.. List Components 1, 0MTP15 1T SAE reducer 1, 0TP0 bushing 1, 0TAP torque arm kit 1, ydraulic motor (separate) Note: See Application Considerations on back cover. 0

Selection and Ordering Information MTP Example No. Units 7 15 ydraulic Screw Conveyor A hydraulic shaft mount reducer is required to convey dry cement powder. The conveyor will be uniformly fed and operated 1 to 16 hours per day. The screw is 14" diameter and has a 7/16" bore with two holes. The conveyor requires 4 1/ hp and will operate at 60. The application requires a waste pack. 1. Determine the Load Classification From the AGMA Application Classification Numbers section, note the AGMA Class Number is II for a uniformly loaded or fed screw conveyor, operating over hours per day.. Determine the Speed Reducer Required From the ydraulic Reducer Selection Chart section, there are four tables for selecting hydraulic shaft mounts for Class II Service. Locate the 60 row, if available, in each table. Read across the row to find a column with a rating of 4 1/ hp or greater. Read up the column to determine the basic reducer size that corresponds to the design hp. For this application, a 115MTP15 9T SAEA, 115MTP5 9T SAEA, 0MTP5 6 SAEA or a 0MTP05 6 SAE A may be used. Generally, the smaller case size is more economical, but the total system should be considered. Select the reducer based upon hydraulic motor characteristics such as spline dimensions and flow rates. (Note: ydraulic motors are not included with the reducer.) For this example, select a 115MTP15 9T SAEA.. Establish Sealing Required for Screw Conveyor The waste pack cartridge is well suited for dry, abrasive materials such as cement powder. Specify the optional waste pack cartridge for the 115 shaft mount selected. From the Accessories section, select part 1150WPP. 4. Select the Screw Conveyor Adapter and Screw Conveyor Shaft Using the basic reducer size, required drive shaft and screw diameter for the selection; refer to Screw Conveyor Drives in the Accessories section. Note the specification was for a 7/16" drive shaft with a two hole arrangement for the 14" diameter screw. From the table select the 115SCAP and the 115DSP07. 5. Select the Trough End From the Screw Conveyor Trough Ends s 7407 table, select the SCTE14 X 7/16 trough end. 6. List of Components: 1, 115MTP15 9T SAEA reducer 1, 115SCAP screw conveyor adapter 1, 115DSP07 screw conveyor drive shaft kit 1, 1150WPP waste pack cartridge 1, SCTE14X 7/16 trough end 1, ydraulic motor (separate) Reducer 7 15 0 07 15 07 15 MTP Exact Ratios Ratio Symbols 05 15 5 5.058 14.876 1 8 4.7000 14.7759 5.5 5.1579 5.1667 5.111 4.884 1 14.91 14.7870 14.8187 14.9704 14.5744 4.750 4.8558 4.7409 4.7094 4.850 4.769 4.4118 Note: See Application Considerations on back cover. 1

Application Classification Numbers AGMA Class Numbers Up to ours Per Day ours Per Day Over ours Per Day AGITATORS (Mixers) Pure Liquids I I II Liquids and Solids I II II Liquids Variable Density I II II LOWERS Centrifugal & Vane I I II Lobe I II II Vane I II II REWING AND DISTILLING ottling Machinery I I II rew Kettles Continuous Duty II II II Cookers Continuous Duty II II II Mash Tubs Continuous Duty II II II Scale opper Frequent Starts II II II CAN FILLING MACINES I I II CAR DUMPERS II III III CAR PULLERS I II II CLARIFIERS I I II CLASSIFIERS I II II CLAY WORKING MACINERY rick Presses II III III riquette Machines II III III Pug Mills I II II COMPACTORS COMPRESSORS Centrifugal I I II Lobe I II II Reciprocating, MultiCylinder II II III Reciprocating, SingleCylinder III III III CONVEYORS GENERAL PURPOSE Includes Apron, Assembly, elt, ucket Chain, Flight, Oven, and Screw Uniformly Loaded or Fed I I II eavy Duty Not Uniformly Fed I II II Severe Duty Reciprocating or Shaker II III III CRANES Dry Dock Main oist Auxiliary oist oom oist Slewing Drive Traction Drive Container Main oist oom oist Trolley Drive Gantry Drive Traction Drive Mill Duty Main oist Auxiliary ridge Travel Trolley Travel Industrial Duty Main Auxiliary ridge Travel Trolley Travel CRUSERS Stone or Ore III III III DREDGES Cable Reels II II II Conveyors II II II Cutter ead Drives III III III Pumps III III III Screen Drives III III III Stackers II II II Winches II II II ELEVATORS ucket I II II Centrifugal Discharge I I II Escalators I I II Freight I II II Gravity Discharge I I II EXTRUDERS General II II II Plastics Variable Speed Drive III III III Speed Drive III III III Rubber Continuous Screw Operation III III III Intermittent Screw Operation III III III FANS Centrifugal I I II AGMA Application Application AGMA Class Numbers Up to ours Per Day ours Per Day Over ours Per Day FANS (Cont d) Cooling Towers III III III Forced Draft II II II Induced Draft II II II Industrial & Mine II II II FEEDERS Apron I II II elt I II II Disc I I II Reciprocating II III III Screw I II II FOOD INDUSTRY Cereal Cooker I I II Dough Mixer II II II Meat Grinders II II II Slicers I II II GENERATORS AND EXCITERS II II II AMMER MILLS III III III OISTS eavy Duty Medium Duty Skip oist LAUNDRY TUMLERS II II II LAUNDRY WASERS II II III LUMER INDUSTRY arkers Spindle Feed II II II Main Drive III III III Conveyors urner II II II Main or eavy Duty II II II Main Log III III III Resaw, MerryGoRound II II II Slab III III III Transfer II II II Chains Floor II II II Green II II III CutOffSaws Chain II II III Drag II II III Debarking Drums III III III Feeds Edger II II II Gang II III III Trimmer II II II Log Deck III III III Log auls Incline Well Type III III III Log Turning Devices III III III Planer Feed II II II Planer Tilting oists II II II Rolls LiveOff rg Roll Cases III III III Sorting Table II II II Tipple oist II II II Transfer Chain II II III Craneway II II III Tray Drives II II II Veneer Lathe Drives II II II METAL MILLS Draw ench Carriage and Main Drive II II II Runout Table NonReversing Group Drives II II II Individual Drives III III III Reversing III III III Slab Pushers II II II Shears III III III Wire Drawing II II II Wire Winding Machine II II II METAL STRIP PROCESSING MACINERY ridges II II II Collers & Uncoilers I I II Edge Trimmers I II II Flatteners II II II Loopers (Accumulators) I I I Pinch Rolls II II II Scrap Choppers II II II Shears III III III Slitters I II II MILLS, ROTARY TYPE all & Rod Spur Ring Gear III III III elical Ring Gear II II II Direct Connected III III III

Application AGMA Application Classification Numbers AGMA Class Numbers Up to ours Per Day ours Per Day Over ours Per Day MILLS, ROTARY TYPE (Cont d) Cement Kilns II II II Dryers & Coolers II II II PAPER MILLS 1) Agitator (Mixer) II II II Agitator For Pure Liquors II II II arking Drums III III III arkers Mechanical III III III eater II II II reaker Stack II II II Calendar ) II II II Chipper III III III Chip Feeder II II II Coating Rolls II II II Conveyors Chip, ark, Chemical II II II Log (Including Slab) III III III Couch Rolls II II II Cutter III III III Cylinder Molds II II II Dryers ) Paper Machine II II II Conveyor Type II II II Embosser II II II Extruder II II II Fourdrinier Rolls (Includes Lump reaker, Dandy Roll, Wire Turning, and Return Rolls) II II II Jordan II II II Kiln Drive II II II Mt. ope Roll II II II Paper Rolls II II II Platter II II II Presses Felt Suction II II II Pulper III III III Pumps Vacuum II II II Reel (Surface Type) II II II Screens Chip II II II R otary II II II Vibrating III III III Press II II II Supercalendar II II II Thickener (AC Motor) II II II Thickener (DC Motor) II II II Washer (AC Motor) II II II Washer (DC Motor) II II II Wind and Unwind Stand I I I Winders (Surface Type) II II II Yankee Dryers ) II II II PLASTICS INDUSTRY PRIMARY PROCESSING Intensive Internal Mixers atch Mixers III III III Continuous Mixers II II II atch Drop Mill Smooth Rolls II II II Continuous Feed, olding & lend Mill II II II Calendars II II II PLASTICS INDUSTRY SECONDARY PROCESSING low Molders II II II Coating II II II Film II II II Pipe II II II PrePlasticizers II II II Rods II II II Sheet II II II Tubing II II II PULLERS ARGE AUL II II II PUMPS Centrifugal I I II Proportioning II II II Reciprocating Single Acting, or more Cylinders II II II Double Acting, or more Cylinders II II II Rotary Gear Type I I II Lobe I I II Vane I I II RUER INDUSTRY Intensive Internal Mixers atch Mixers III III III Continuous Mixers II II II Mixing Mill Smooth Rolls II II II 1 or Corrugated Rolls III III III Application AGMA Class Numbers Up to Over ours Per Day ours Per Day ours Per Day RUER INDUSTRY (Cont d) atch Drop Mill Smooth Rolls II II II Cracker Warmer Roll, 1 Corrugated Roll III III III Cracker Corrugated Rolls III III III olding, Feed & lend Mill Rolls II II II Refiner Rolls II II II Calendars II II II SAND MULLER II II II SEWAGE DISPOSAL EQUIPMENT ar Screens II II II Chemical Feeder II II II Dewatering Screens II II II Scum reakers II II II Slow or Rapid Mixers II II II Sludge Collectors II II II Thickener II II II Vacuum Filters II II II SCREENS Air Washing I I II Rotary Stone or Gravel II II II Traveling Water Intake I I I SCREW CONVEYORS Uniformly Loaded or Fed I I II eavy Duty I II II SUGAR INDUSTRY eet Slicer III III III Cane Knives II II II Crushers II II II Mills (Low Speed End) III III III TEXTILE INDUSTRY atchers II II II Calendars II II II Cards II II II Dry Cans II II II Dyeing Machinery II II II Looms II II II Mangles II II II Nappers II II II Pads II II II Slashers II II II Soapers II II II Spinners II II II Tenter Frames II II II Washers II II II Winders II II II Notes: 1) The Class numbers listed in the table for paper mill applications are consistent with those shown in TAPPI (Technical Association of Pulp and Paper Industry) Technical information sheet 040618 1967, Service Factors for Gears on Major Equipment in the Pulp and Paper Industry. ) Antifriction bearings only. Contact Application Engineering (1 800 66 09) for the selection of an AGMA Class Numbers in these applications. MTP

MTP Selection Chart Class I Service (1.0 S.F.) Involute Spline RPM Single Reduction 7MTP05 1T SAE 115MTP05 1T SAE 0MTP05 14T SAEC4 07MTP05 14T SAEC4 15MTP05 14T SAEC4 (lbins) (lbins) (lbins) (lbins) (lbins) 90 4.55,078 7.55 5,111 14.74 9,980 17.9 1,17 8.16 19,064 0 4.89,978 8.9 5,111 15.86 9,66 19.7 11,740 0.08 18,7 1 5.,890 9. 5,111 16.94 9,8 0.59 11,40.07 17,76 5.54,81.07 5,111 17.99 9,16 1.87 11,.99 17,55 5.85,74.91 5,111 19.0 8,914.1,8 5.85 16,80 140 6.16,680 11.75 5,111 0.0 8,71 4.,587 15,666 150 6.45,6 1.58 5,111 8,159 5.5,65 14,6 160 6.75,569 1.4 5,111 7,649 6.69,164 1,708 170 7.0,50 14.01 5,00 7,199 7.8 9,975 1,90 180 7.1,475 14.58 4,94 6,799 8.97 9,804 1,185 190 7.59,44 14.58 4,675 6,441 0.07 9,64 11,544 00 7.86,94 14.58 4,441 6,119 1.15 9,490,966 8.1,57 14.58 4,0 5,88 1.50 9,19,444 0 8.9, 14.58 4,08 5,56 1.50 8,7 9,969 0 8.65,90 14.58,86 5,1 1.50 8,44 9,56 40 8.90,59 14.58,701 5,099 1.50 7,996 9,19 50 9.15,0 14.58,55 4,895 1.50 7,676 8,77 60 9.40,0 14.58,416 4,707 1.50 7,81 8,46 70 9.64,176 14.58,90 4,5 1.50 7,8 8,1 80 9.88,151 14.58,17 4,71 1.50 6,854 7,8 90.1,17 14.58,06 4,0 1.50 6,618 7,56 00.6,4 14.58,961 4,079 1.50 6,97 7,11.60,08 14.58,865,948 1.50 6,191 7,075 0.8,061 14.58,776,85 1.50 5,997 6,854 0 11.05,041 14.58,69,709 1.50 5,815 6,646 40 11.8,01 14.58,61,600 1.50 5,644 6,451 50 11.4 1,974 14.58,58,497 1.50 5,48 6,66 60 11.4 1,919 14.58,467,400 1.50 5,1 6,09 70 11.4 1,867 14.58,401,08 1.50 5,187 5,98 80 11.4 1,818 14.58,8,1 1.50 5,050 5,77 90 11.4 1,771 14.58,78,18 1.50 4,91 5,64 400 11.4 1,77 14.58,1,060 1.50 4,798 5,48 4

MTP Selection Chart Class I Service (1.0 S.F.) MTP Involute Spline RPM Double Reduction 7MTP15 9T SAEA 7MTP5 9T SAEA 115MTP15 9T SAEA 115MTP5 9T SAEA 0MTP15 1T SAE 0MTP5 9T SAEA 07MTP15 1T SAE (lbins) (lbins) (lbins) (lbins) (lbins) (lbins) (lbins) 0.9 5,658 0.9 5,658 1.6 7,655 1.6 7,655.18 1,60.1 1,915.64 16,081 0 1.78 5,44 1.78 5,44.41 7,41.41 7,41 4.16 1,684 4.16 1,684 5.8 16,081 0.61 5,01.61 5,01.57 7,4.57 7,4 6.16 1,506 6.16 1,506 7.9 16,081 40.4 5,04.4 5,04 4.71 7,168 4.71 7,168 8.1 1,7 8.1 1,7.56 16,081 50 4.1 5,18 4.1 5,18 5.8 7,7 5.8 7,7.06 1,6 9.46 11,51 1.0 16,081 60 4.99 5,065 4.99 5,065 6.95 7,055 6.95 7,055 11. 11,498.68,847 15.84 16,081 70 5.76 5,011 5.76 5,011 8.05 7,009 8.05 7,009 1.45,87 11.7,0 18.48 16,081 80 6.5 4,964 6.5 4,964 9.15 6,969 9.15 6,969 1.50,85 1.69 9,667 1.1 16,081 90 7.7 4,9.4 6,9 14.51 9,80.7 16,064 0 8.0 4,884 11. 6,899 15.46 9,40 5.54 15,56 1 8.76 4,850 1.40 6,868 16.47 9,11 7.1 15,15 9.49 4,818 1.60 6,97 17.45 8,857 9.0 14,76. 4,788 1.60 5,905 18.9 8,60 0.70 14,87 RPM Double Reduction 07MTP5 1T SAE 15MTP15 14T SAEC4 15MTP5 1T SAE 07MTP15 14T SAEC4 07MTP5 14T SAEC4 15MTP15 14T SAEC4 15MTP5 14T SAEC4 (lbins) (lbins) (lbins) (lbins) (lbins) (lbins) (lbins).44 0,966 5.59 4,066 4.44 7,05 9.64 58,758 9.64 58,758 1.4 75,06 1.4 75,06 0 6.58 0,059.65,46 8.87 7,05 18.47 56,66 18.47 56,66.67 7,5.67 7,5 0 9.7 19,769 15.7 1,951 1.1 7,05 6.97 54,771 6.97 54,771 4.55 70,167 4.55 70,167 40 1.8 19,549 0.7 1,58 17.74 7,05 4.9 5,8.68 51,9 45.1 68,741 45.1 68,741 50 15.4 18,796 4.54 9,905.18 7,05 40.09 48,847 9.7 47,97 54.00 65,798 50.40 61,41 60 17.5 17,796 7.88 8,14 6.61 7,05 45.00 45,69 41.40 4,08 54.00 54,8 50.40 51,176 70 19.5 16,991 1.06 7,0 9.70 5,849 45.00 9,166 41.40 6,0 54.00 46,999 50.40 4,865 80 1.4 16, 4. 5,97 9.70,618 45.00 4,70 41.40 1,58 54.00 41,14 50.40 8,8 90 4,70 45.00 0,46 54.00 6,555 0 1,9 45.00 7,416 54.00,899 1 19,99 45.00 4,94 54.00 9,908 18,77 45.00,847 54.00 7,416 16,871 45.00 1,089 54.00 5,07 5

MTP Selection Chart Class I Service (1.0 S.F.) Straight Sided Spline RPM Single Reduction 7MTP05 6 SAEA 115MTP05 6 SAEA 0MTP05 6 SAEA 07MTP05 6 SAEA 15MTP05 6 SAEA (lbins) (lbins) (lbins) (lbins) (lbins) 1 0.07 4,089 0.1 7,496 0.18,905 0.5 14,994 0.6 15,7 5 0.7,71 0.5 6,66 0.8,156 1.04 1,68 1.9 15,7 0.5,169 1.0 6,5 1.65,06.0 1,94.58 15,7 0 1.0,118.0 6,154.9,016 4.0 1,49 5.16 15,7 0 1.5,1.0 6,11 4.9,000 6.01 1,01 7.75 15,7 40.0,09 4.0 6,119 6.56 9,99 7.99 1,177. 15,7 50.5,087 5.0 6,11 8.0 9,988 9.98 1,16 1.91 15,7 60.04,084 6.01 6,7 9.8 9,985 11.97 1,15 15.49 15,7 70.54,081 7.01 6,4 11.47 9,98 1.95 1,146 18.08 15,7 80 4.04,080 8.01 6,1 1.11 9,981 15.94 1,141 0.66 15,7 90 4.55,078 9.01 6,099 14.74 9,980 17.9 1,17.4 15,7 0 4.89,978 9.69 5,906 15.86 9,66 19.7 11,740 5.8 15,7 1 5.,890.6 5,77 16.94 9,8 0.59 11,40 8.40 15,7 5.54,81 11.00 5,586 17.99 9,16 1.87 11, 0.99 15,7 5.85,74 11.6 5,450 19.0 8,914.1,8.57 15,7 140 6.16,680 1.4 5,8 0.0 8,71 4.,587 15,666 150 6.45,6 1.60 5,118 8,159 5.5,65 14,6 160 6.75,569 1.60 4,798 7,649 6.69,164 1,708 170 7.0,50 1.60 4,516 7,199 7.8 9,975 1,90 180 7.1,475 1.60 4,65 6,799 8.97 9,804 1,185 190 7.59,44 1.60 4,040 6,441 0.07 9,64 11,544 00 7.86,94 1.60,88 6,119 1.15 9,490,966 8.1,57 1.60,655 5,88 1.50 9,19,444 0 8.9, 1.60,489 5,56 1.50 8,7 9,969 0 8.65,90 1.60,8 5,1 1.50 8,44 9,56 40 8.90,59 1.60,199 5,099 1.50 7,996 9,19 50 9.15,0 1.60,071 4,895 1.50 7,676 8,77 60 9.40,0 1.60,95 4,707 1.50 7,81 8,46 70 9.64,176 1.60,84 4,5 1.50 7,8 8,1 80 9.88,151 1.60,74 4,71 1.50 6,854 7,8 90.1,17 1.60,647 4,0 1.50 6,618 7,56 00.6,4 1.60,559 4,079 1.50 6,97 7,11.60,08 1.60,476,948 1.50 6,191 7,075 0.8,061 1.60,99,85 1.50 5,997 6,854 0 11.05,041 1.60,6,709 1.50 5,815 6,646 40 11.8,01 1.60,58,600 1.50 5,644 6,451 50 11.4 1,974 1.60,19,497 1.50 5,48 6,66 60 11.4 1,919 1.60,1,400 1.50 5,1 6,09 70 11.4 1,867 1.60,075,08 1.50 5,187 5,98 80 11.4 1,818 1.60,00,1 1.50 5,050 5,77 90 11.4 1,771 1.60 1,968,18 1.50 4,91 5,64 400 11.4 1,77 1.60 1,919,060 1.50 4,798 5,48 6

MTP Selection Chart Class I Service (1.0 S.F.) MTP Straight Sided Spline RPM Double Reduction 0MTP5 6 SAEA 07MTP15 6 SAEA 07MTP5 6 SAEA 15MTP5 6 SAEA 07MTP5 6 SAEA 15MTP5 6 SAEA (lbins) (lbins) (lbins) (lbins) (lbins) (lbins) 1 0.19 11,569 0.9 17,71 0.9 17,71 0.49 9,989 0.91 55,479 1.1 68,156 5 1.17 14,68 1.85,570 1.85,570.99 6,404 4.98 60,698 6. 74,4.18 1,60.44 0,966.44 0,966 5.59 4,066 9.64 58,758 1.0 74,4 0 4.16 1,684 6.58 0,059 6.58 0,059.65,46 18.47 56,66.67 7,5 0 6.16 1,506 9.7 19,769 9.7 19,769 15.7 1,951 6.97 54,771 4.55 70,167 40 8.1 1,7 1.8 19,549 1.8 19,549 0.7 1,58.68 51,9 45.1 68,741 50 9.46 11,51 15.7 19,16 15.4 18,796 4.99 0,450 9.7 47,97 50.40 61,41 60.68,847 17.87 18,141 17.5 17,796 8.9 8,89 41.40 4,08 50.40 51,176 70 11.7,0 19.90 17,1 19.5 16,991 9.70 5,849 41.40 6,0 50.40 4,865 80 1.69 9,667 1.85 16,641 1.4 16, 9.70,618 41.40 1,58 50.40 8,8 90.7 16,064 0 5.54 15,56 1 7.1 15,15 9.0 14,76 0.70 14,87 7

Involute Spline RPM MTP Selection Chart Class II Service (1.4 S.F.) Single Reduction 7MTP05 1T SAE 115MTP05 1T SAE 0MTP05 14T SAEC4 07MTP05 14T SAEC4 15MTP05 14T SAEC4 (lbins) (lbins) (lbins) (lbins) (lbins) 90.5,199 5.9,651.5 7,18 1.81 8,669 0.1 1,617 0.49,17 5.99,651 11. 6,90 1.76 8,86 1.49 1,091 1.7,064 6.59,651 1. 6,70 14.70 8,144.91 1,687.96,009 7.19,651 1.85 6,56 15.6 7,90 4.8 1,5 4.18 1,959 7.79,651 1.59 6,67 16.51 7,78 5.61 1,00 140 4.40 1,914 8.9,651 14.0 6,4 17.8 7,56 6.91 11,709 150 4.61 1,87 8.99,651 15.00 6,09 18. 7,404 8.18 11,444 160 4.8 1,85 9.59,651 15.69 5,97 19.07 7,60 9.41 11,199 170 5.0 1,800.01,586 16.5 5,861 19.88 7,15 0.6,97 180 5. 1,768.41,54 17.01 5,759 0.69 7,00 1.81,765 190 5.4 1,78.81,465 17.66 5,664 1.48 6,887.97,57 00 5.61 1,7 11.0,411 18.0 5,576.5 6,778 4.11,90 5.80 1,684 11.58,61 18.9 5,491.01 6,676 5.,0 0 5.99 1,659 11.96,14 19.55 5,41.77 6,581 9,969 0 6.18 1,66 1.4,68 5,1 4.5 6,494 9,56 40 6.6 1,614 1.70,5 5,099 5.4 6,407 9,19 50 6.54 1,59 1.07,186 4,895 5.96 6,7 8,77 60 6.71 1,57 1.4,147 4,707 6.68 6,5 8,46 70 6.89 1,554 1.79,111 4,5 7.9 6,180 8,1 80 7.06 1,56 14.1,076 4,71 8.09 6,11 7,8 90 7. 1,519 14.48,04 4,0 8.78 6,046 7,56 00 7.40 1,50 14.58,961 4,079 9.46 5,98 7,11 7.57 1,488 14.58,865,948 0.14 5,94 7,075 0 7.7 1,47 14.58,776,85 0.81 5,866 6,854 0 7.90 1,458 14.58,69,709 1.45 5,807 6,646 40 8.06 1,444 14.58,61,600 1.50 5,644 6,451 50 8. 1,41 14.58,58,497 1.50 5,48 6,66 60 8.8 1,418 14.58,467,400 1.50 5,1 6,09 70 8.5 1,405 14.58,401,08 1.50 5,187 5,98 80 8.69 1,9 14.58,8,1 1.50 5,050 5,77 90 8.85 1,8 14.58,78,18 1.50 4,91 5,64 400 9.00 1,71 14.58,1,060 1.50 4,798 5,48 8

MTP Selection Chart Class II Service (1.4 S.F.) MTP Involute Spline RPM Double Reduction 7MTP15 9T SAEA 7MTP5 9T SAEA 115MTP15 9T SAEA 115MTP5 9T SAEA 0MTP15 1T SAE 0MTP5 9T SAEA 07MTP15 1T SAE (lbins) (lbins) (lbins) (lbins) (lbins) (lbins) (lbins) 0.66 4,041 0.66 4,041 0.90 5,468 0.90 5,468 1.55 9,47 1.51 9,5 1.89 11,486 0 1.7,88 1.7,88 1.7 5,44 1.7 5,44.97 9,060.97 9,060.77 11,486 0 1.86,786 1.86,786.55 5,17.55 5,17 4.40 8,9 4.40 8,9 5.66 11,486 40.44,717.44,717.6 5,.6 5, 5.80 8,87 5.80 8,87 7.54 11,486 50.01,66.01,66 4.17 5,076 4.17 5,076 7.19 8,758 6.76 8,6 9.4 11,486 60.56,618.56,618 4.96 5,09 4.96 5,09 8.09 8,1 7.6 7,748 11.1 11,486 70 4.11,580 4.11,580 5.75 5,007 5.75 5,007 8.89 7,741 8.7 7,88 1.0 11,486 80 4.66,546 4.66,546 6.54 4,978 6.54 4,978 9.65 7,46 9.07 6,905 15.08 11,486 90 5.19,516 7.1 4,95.6 7,014 16.95 11,475 0 5.7,489 8.09 4,98 11.04 6,78 18.5 11,117 1 6.5,464 8.86 4,905 11.76 6,515 19.51,804 6.78,441 9.6 4,885 1.46 6,7 0.7,56 7.0,40.8 4,865 1.14 6,157 1.9,76 RPM Double Reduction 07MTP5 1T SAE 15MTP15 14T SAEC4 15MTP5 1T SAE 07MTP15 14T SAEC4 07MTP5 14T SAEC4 15MTP15 14T SAEC4 15MTP5 14T SAEC4 (lbins) (lbins) (lbins) (lbins) (lbins) (lbins) (lbins).46 14,976.99 4,.17 19,0 6.89 41,970 6.89 41,970 8.8 5,719 8.8 5,719 0 4.70 14,8 7.61,168 6.4 19,0 1.19 40,190 1.19 40,190 16.91 51,50 16.91 51,50 0 6.95 14,11 11.4,8 9.51 19,0 19.6 9,1 19.6 9,1 4.68 50,119 4.68 50,119 40 9.17 1,96 14.81,559 1.67 19,0 4.49 7,06 4.05 6,67.4 49,0.4 49,0 50 11.0 1,46 17.5 1,61 15.84 19,0 8.6 4,891 8.1 4,67 9.64 48,99 9.64 48,99 60 1.5 1,711 19.9 0,5 19.01 19,0.5,0 1.95,441 46.47 47,185 46.54 47,61 70 1.94 1,16.19 19,09.18 19,0 6.4 1,540 5.59 0,977 51.76 45,050 50.40 4,865 80 15.1 11,660 4.6 18,55 4.80 18,889 9.79 0,01 9.08 9,758 54.00 41,14 50.40 8,8 90 6.45 17,908 4.1 9,49 54.00 6,555 0 8.48 17,51 45.00 7,416 54.00,899 1 0.44 16,861 45.00 4,94 54.00 9,908.5 16,46 45.00,847 54.00 7,416 4. 16,07 45.00 1,089 54.00 5,07 9

MTP Selection Chart Class II Service (1.4 S.F.) Straight Sided Spline RPM Single Reduction 7MTP05 6 SAEA 115MTP05 6 SAEA 0MTP05 6 SAEA 07MTP05 6 SAEA 15MTP05 6 SAEA (lbins) (lbins) (lbins) (lbins) (lbins) 1 0.05,91 0.09 5,54 0.1 7,789 0.18,7 0.18 11,8 5 0.19,7 0.7 4,547 0.60 7,54 0.74 9,059 0.9 11,8 0.7,64 0.7 4,446 1.18 7,188 1.45 8,85 1.84 11,8 0 0.7,7 1.44 4,96.5 7,154.87 8,749.69 11,8 0 1.09,15.16 4,79.5 7,14 4.9 8,715 5.5 11,8 40 1.45,09.87 4,71 4.69 7,17 5.71 8,698 7.8 11,8 50 1.81,05.58 4,66 5.85 7,14 7.1 8,687 9. 11,8 60.17,0 4.0 4,6 7.0 7,1 8.55 8,681 11.07 11,8 70.5,01 5.01 4,60 8.19 7, 9.97 8,676 1.91 11,8 80.89,00 5.7 4,58 9.6 7,19 11.9 8,67 14.76 11,8 90.5,199 6.44 4,57.5 7,18 1.81 8,669 16.60 11,8 0.49,17 6.9 4,19 11. 6,90 1.76 8,86 18.44 11,8 1.7,064 7.40 4,098 1. 6,70 14.70 8,144 0.9 11,8.96,009 7.86,990 1.85 6,56 15.6 7,90.1 11,8 4.18 1,959 8.1,89 1.59 6,67 16.51 7,78.98 11,8 140 4.40 1,914 8.75,806 14.0 6,4 17.8 7,56 5.8 11,8 150 4.61 1,87 9.17,76 15.00 6,09 18. 7,404 7.67 11,8 160 4.8 1,85 9.59,65 15.69 5,97 19.07 7,60 9.41 11,199 170 5.0 1,800.01,586 16.5 5,861 19.88 7,15 0.6,97 180 5. 1,768.41,54 17.01 5,759 0.69 7,00 1.81,765 190 5.4 1,78.81,465 17.66 5,664 1.48 6,887.97,57 00 5.61 1,7 11.0,411 18.0 5,576.5 6,778 4.11,90 5.80 1,684 11.58,61 18.9 5,491.01 6,676 5.,0 0 5.99 1,659 11.96,14 19.55 5,41.77 6,581 9,969 0 6.18 1,66 1.4,68 5,1 4.5 6,494 9,56 40 6.6 1,614 1.70,5 5,099 5.4 6,407 9,19 50 6.54 1,59 1.07,186 4,895 5.96 6,7 8,77 60 6.71 1,57 1.4,147 4,707 6.68 6,5 8,46 70 6.89 1,554 1.79,111 4,5 7.9 6,180 8,1 80 7.06 1,56 14.1,076 4,71 8.09 6,11 7,8 90 7. 1,519 14.48,04 4,0 8.78 6,046 7,56 00 7.40 1,50 14.58,961 4,079 9.46 5,98 7,11 7.57 1,488 14.58,865,948 0.14 5,94 7,075 0 7.7 1,47 14.58,776,85 0.81 5,866 6,854 0 7.90 1,458 14.58,69,709 1.45 5,807 6,646 40 8.06 1,444 14.58,61,600 1.50 5,644 6,451 50 8. 1,41 14.58,58,497 1.50 5,48 6,66 60 8.8 1,418 14.58,467,400 1.50 5,1 6,09 70 8.5 1,405 14.58,401,08 1.50 5,187 5,98 80 8.69 1,9 14.58,8,1 1.50 5,050 5,77 90 8.85 1,8 14.58,78,18 1.50 4,91 5,64 400 9.00 1,71 14.58,1,060 1.50 4,798 5,48 40

MTP Selection Chart Class II Service (1.4 S.F.) MTP Straight Sided Spline RPM Double Reduction 0MTP5 6 SAEA 07MTP15 6 SAEA 07MTP5 6 SAEA 15MTP5 6 SAEA 07MTP5 6 SAEA 15MTP5 6 SAEA (lbins) (lbins) (lbins) (lbins) (lbins) (lbins) 1 0.14 8,64 0.1 1,658 0.1 1,658 0.5 1,40 0.65 9,68 0.80 48,68 5 0.84,19 1. 16,11 1. 16,11.1 6,00.56 4,56 4.6 5,096 1.55 9,47.46 14,976.46 14,976.99 4, 6.89 41,970 8.71 5,096 0.97 9,060 4.70 14,8 4.70 14,8 7.61,168 1.19 40,190 16.91 51,50 0 4.40 8,9 6.95 14,11 6.95 14,11 11.4,8 19.6 9,1 4.68 50,119 40 5.80 8,87 9.17 1,96 9.17 1,96 14.81,559 4.05 6,67.4 49,0 50 6.76 8,6 11. 1,687 11.0 1,46 17.85 1,750 8.1 4,67 9.64 48,99 60 7.6 7,748 1.76 1,958 1.5 1,711 0.8 0,59 1.95,441 46.54 47,61 70 8.7 7,88 14. 1,7 1.94 1,16.59 19,66 5.59 0,977 50.40 4,865 80 9.07 6,905 15.61 11,886 15.1 11,660 4.80 18,889 9.08 9,758 50.40 8,8 90 16.95 11,475 0 18.5 11,117 1 19.51,804 0.7,56 1.9,76 41

MTP Selection Chart Class III Service (.0 S.F.) Involute Spline RPM Single Reduction 7MTP05 1T SAE 115MTP05 1T SAE 0MTP05 14T SAEC4 07MTP05 14T SAEC4 15MTP05 14T SAEC4 (lbins) (lbins) (lbins) (lbins) (lbins) 90.7 1,59.78,556 7.7 4,990 8.96 6,068 14.08 9,5 0.44 1,489 4.19,556 7.9 4,81 9.6 5,870 15.04 9,164 1.61 1,445 4.61,556 8.47 4,69.9 5,701 16.0 8,881.77 1,406 5.0,556 9.00 4,568.9 5,551 16.99 8,67.9 1,71 5.45,556 9.51 4,457 11.56 5,417 17.9 8,40 140.08 1,40 5.87,556.01 4,57 1.16 5,94 18.8 8,197 150. 1,11 6.9,556.50 4,65 1.76 5,18 19.7 8,011 160.7 1,84 6.71,556.98 4,181 1.5 5,08 0.59 7,89 170.5 1,60 7.00,5 11.45 4, 1.9 4,987 1.4 7,681 180.66 1,8 7.9,467 11.91 4,01 14.48 4,90.6 7,56 190.79 1,17 7.57,46 1.6,965 15.0 4,81.08 7,401 00.9 1,197 7.84,88 1.81,90 15.58 4,745.88 7,7 4.06 1,179 8.11,5 1.5,844 16.11 4,67 4.66 7,154 0 4.19 1,161 8.8,19 1.68,789 16.64 4,607 5.4 7,04 0 4. 1,145 8.64,87 14.11,77 17.16 4,546 6.19 6,99 40 4.45 1,19 8.89,58 14.5,689 17.67 4,485 6.94 6,840 50 4.57 1,115 9.15,0 14.95,64 18.17 4,49 7.67 6,744 60 4.70 1,1 9.40,0 15.6,599 18.67 4,76 8.40 6,654 70 4.8 1,088 9.65,178 15.76,556 19.17 4,6 9.1 6,571 80 4.94 1,075 9.89,15 16.16,517 19.67 4,79 9.8 6,488 90 5.06 1,06.14, 16.56,479 0.14 4, 0.5 6,41 00 5.18 1,05.8,8 16.95,44 0.6 4,188 1.1 6,9 5.0 1,041.6,087 17.4,408 1. 4,147 1.88 6,66 0 5.41 1,01.85,066 17.7,74 1.57 4,6.57 6,00 0 5.5 1,00 11.08,046 18.,4.0 4,065. 6,15 40 5.64 1,011 11.,09 18.48,11.47 4,07.89 6,07 50 5.75 1,001 11.55,011 18.85,8.94,99 4.5 6,011 60 5.86 99 11.77 1,99 19.,5.9,958 5.17 5,95 70 5.97 984 1.00 1,976 19.59,5.8,94 5.8 5,899 80 6.08 975 1. 1,960 19.95,198 4.8,89 5,77 90 6.19 967 1.44 1,944,18 4.7,86 5,64 400 6.0 959 1.66 1,99,060 5.15,81 5,48 4

MTP Selection Chart Class III Service (.0 S.F.) MTP Involute Spline RPM Double Reduction 7MTP15 9T SAEA 7MTP5 9T SAEA 115MTP15 9T SAEA 115MTP5 9T SAEA 0MTP15 1T SAE 0MTP5 9T SAEA 07MTP15 1T SAE (lbins) (lbins) (lbins) (lbins) (lbins) (lbins) (lbins) 0.46,89 0.46,89 0.6,87 0.6,87 1.09 6,60 1.06 6,457 1. 8,040 0 0.89,717 0.89,717 1.0,671 1.0,671.08 6,4.08 6,4.64 8,040 0 1.1,650 1.1,650 1.78,61 1.78,61.08 6,5.08 6,5.96 8,040 40 1.71,60 1.71,60.5,584.5,584 4.06 6,186 4.06 6,186 5.8 8,040 50.,564.,564.9,55.9,55 5.0 6,11 4.7 5,765 6.60 8,040 60.49,5.49,5.47,57.47,57 5.66 5,749 5.4 5,4 7.9 8,040 70.88,506.88,506 4.0,505 4.0,505 6. 5,419 5.86 5, 9.4 8,040 80.6,48.6,48 4.58,484 4.58,484 6.75 5,14 6.5 4,8.56 8,040 90.64,461 5.1,466 7.5 4,9 11.87 8,0 0 4.01,44 5.66,449 7.7 4,7 1.77 7,78 1 4.8,45 6.0,44 8. 4,561 1.65 7,56 4.74,409 6.7,419 8.7 4,49 14.51 7,68 5.11,94 7.7,406 9.0 4, 15.5 7,19 RPM Double Reduction 07MTP5 1T SAE 15MTP15 14T SAEC4 15MTP5 1T SAE 07MTP15 14T SAEC4 07MTP5 14T SAEC4 15MTP15 14T SAEC4 15MTP5 14T SAEC4 (lbins) (lbins) (lbins) (lbins) (lbins) (lbins) (lbins) 1.7,48.80 17,0. 1,51 4.8 9,79 4.8 9,79 6.17 7,60 6.17 7,60 0.9,09 5. 16,18 4.44 1,51 9.4 8,1 9.4 8,1 11.8 6,05 11.8 6,05 0 4.87 9,884 7.87 15,975 6.65 1,51 1.48 7,85 1.48 7,85 17.8 5,08 17.8 5,08 40 6.4 9,774.7 15,791 8.87 1,51 17.14 6,114 16.84 5,646.57 4,70.57 4,70 50 7.71 9,98 1.7 14,95 11.09 1,51 0.04 4,4 19.69,987 7.75,8 7.75,8 60 8.76 8,898 1.94 14,157 1.1 1,51.77,1.6,708.5,09.58,08 70 9.76 8,496 15.5 1,516 15.5 1,51 5.7,078 4.91 1,684 6. 1,55 6.08 1,406 80.7 8,16 17.05 1,986 17.6 1, 7.85 1,11 7.5 0,81 9.78 0,97 9.44 0,07 90 18.5 1,55 0.4 0,474 4.0 9,47 0 19.94 1,146.56 19,88 46.51 8,6 1 1.1 11,80 4.81 19,79 49.7 7,57.65 11,498 6.99 18,78 5.84 6,87.95 11,6 9.1 18,6 54.00 5,07 4

MTP Selection Chart Class III Service (.0 S.F.) Straight Sided Spline RPM Single Reduction 7MTP05 6 SAEA 115MTP05 6 SAEA 0MTP05 6 SAEA 07MTP05 6 SAEA 15MTP05 6 SAEA (lbins) (lbins) (lbins) (lbins) (lbins) 1 0.0,045 0.06,748 0.09 5,45 0.1 7,497 0.1 7,866 5 0.1 1,66 0.6,18 0.4 5,078 0.5 6,41 0.65 7,866 0.6 1,585 0.51,11 0.8 5,01 1.0 6,197 1.9 7,866 0 0.51 1,559 1.01,077 1.64 5,008.01 6,15.58 7,866 0 0.76 1,550 1.51,065.46 5,000.00 6,0.87 7,866 40 1.0 1,546.01,059.8 4,996 4.00 6,088 5.16 7,866 50 1.7 1,544.51,056 4. 4,994 4.99 6,081 6.46 7,866 60 1.5 1,54.01,054 4.9 4,99 5.98 6,076 7.75 7,866 70 1.77 1,541.51,05 5.7 4,991 6.98 6,07 9.04 7,866 80.0 1,540 4.01,051 6.55 4,990 7.97 6,070. 7,866 90.7 1,59 4.51,050 7.7 4,990 8.96 6,068 11.6 7,866 0.44 1,489 4.85,95 7.9 4,81 9.6 5,870 1.91 7,866 1.61 1,445 5.18,868 8.47 4,69.9 5,701 14.0 7,866.77 1,406 5.50,79 9.00 4,568.9 5,551 15.49 7,866.9 1,71 5.81,75 9.51 4,457 11.56 5,417 16.78 7,866 140.08 1,40 6.1,664.01 4,57 1.16 5,94 18.08 7,866 150. 1,11 6.4,609.50 4,65 1.76 5,18 19.7 7,866 160.7 1,84 6.7,557.98 4,181 1.5 5,08 0.59 7,89 170.5 1,60 7.00,5 11.45 4, 1.9 4,987 1.4 7,681 180.66 1,8 7.9,467 11.91 4,01 14.48 4,90.6 7,56 190.79 1,17 7.57,46 1.6,965 15.0 4,81.08 7,401 00.9 1,197 7.84,88 1.81,90 15.58 4,745.88 7,7 4.06 1,179 8.11,5 1.5,844 16.11 4,67 4.66 7,154 0 4.19 1,161 8.8,19 1.68,789 16.64 4,607 5.4 7,04 0 4. 1,145 8.64,87 14.11,77 17.16 4,546 6.19 6,99 40 4.45 1,19 8.89,58 14.5,689 17.67 4,485 6.94 6,840 50 4.57 1,115 9.15,0 14.95,64 18.17 4,49 7.67 6,744 60 4.70 1,1 9.40,0 15.6,599 18.67 4,76 8.40 6,654 70 4.8 1,088 9.65,178 15.76,556 19.17 4,6 9.1 6,571 80 4.94 1,075 9.89,15 16.16,517 19.67 4,79 9.8 6,488 90 5.06 1,06.14, 16.56,479 0.14 4, 0.5 6,41 00 5.18 1,05.8,8 16.95,44 0.6 4,188 1.1 6,9 5.0 1,041.6,087 17.4,408 1. 4,147 1.88 6,66 0 5.41 1,01.85,066 17.7,74 1.57 4,6.57 6,00 0 5.5 1,00 11.08,046 18.,4.0 4,065. 6,15 40 5.64 1,011 11.,09 18.48,11.47 4,07.89 6,07 50 5.75 1,001 11.55,011 18.85,8.94,99 4.5 6,011 60 5.86 99 11.77 1,99 19.,5.9,958 5.17 5,95 70 5.97 984 1.00 1,976 19.59,5.8,94 5.8 5,899 80 6.08 975 1. 1,960 19.95,198 4.8,89 5,77 90 6.19 967 1.44 1,944,18 4.7,86 5,64 400 6.0 959 1.66 1,99,060 5.15,81 5,48 44

MTP Selection Chart Class III Service (.0 S.F.) MTP Straight Sided Spline RPM Double Reduction 0MTP5 6 SAEA 07MTP15 6 SAEA 07MTP5 6 SAEA 15MTP5 6 SAEA 07MTP5 6 SAEA 15MTP5 6 SAEA (lbins) (lbins) (lbins) (lbins) (lbins) (lbins) 1 0.09 5,785 0.15 8,860 0.15 8,860 0.5 14,994 0.46 7,79 0.56 4,078 5 0.59 7,14 0.9 11,85 0.9 11,85 1.49 18,0.49 0,49.05 7,167 1.09 6,60 1.7,48 1.7,48.80 17,0 4.8 9,79 6. 7,167 0.08 6,4.9,09.9,09 5. 16,18 9.4 8,1 11.8 6,05 0.08 6,5 4.87 9,884 4.87 9,884 7.87 15,975 1.48 7,85 17.8 5,08 40 4.06 6,186 6.4 9,774 6.4 9,774.7 15,791 16.84 5,646.57 4,70 50 4.7 5,765 7.86 9,581 7.71 9,98 1.49 15,5 19.69,987 7.75,8 60 5.4 5,4 8.9 9,071 8.76 8,898 14.0 14,414.6,708.58,08 70 5.86 5, 9.95 8,661 9.76 8,496 15.81 1,76 4.91 1,684 6.08 1,406 80 6.5 4,8.9 8,0.7 8,16 17.6 1, 7.5 0,81 9.44 0,07 90 11.87 8,0 0 1.77 7,78 1 1.65 7,56 14.51 7,68 15.5 7,19 45

Shaft Mount Reducers MTP TorqTaper Plus Unit s 715 C A O L K J M P P1 R D F E Ø MC Ø1 T S W N G Y 90 P1 P Reversible single bushing system mounted on the back side. L O M PF Q WF RF TF SF Reversible single bushing system mounted on the front side. olt AA MC A A4 A AC AD 46 UNIT NO. YDRAULIC MOTOR MOUNTING STYLES 6 9T 1T 14T A A A A 7 1.0.8 0.64 1.89 115 1.01.6 0.6 1.87 1.8.15 0 1.06.7 0.7 1.98 1.1 1.9 1.40.9 07 1..41 1.16 1.97 1.9.91 15 1.0.9 0.91. 1.4.94 07 1.06.4 1.47.98 15 1.1.50 1.54.05

Shaft Mount Reducers MTP TorqTaper Plus Unit s 715 MTP PART NO. DIMENSIONS IN INCES A C D E F G 1 J K L MC O O P P1 7MTP 9.76 1.07 4.88 4.88 7.19.07 7.75.5.00 0.6 5.5 7.89 1.75 4.5 4.1 0.90 1.84 1.14 115MTP 11.00 14.08 5.50 5.50 8.58 11.78 8.69 4.1.50 0.75 5.99 8.6 1.88 4.48 4.45 0.90 1.8 1.14 0MTP 1.88 16.16 6.44 6.44 9.7 1.66.8 4.50.75 0.87 7.07 9.4 1.88 5.01 4.99 0.89 1.8 1. 07MTP 14.50 16.47 7.5 7.5 11. 15.7 11.76 4.88 4.5 1.01 7.9 9.75 1.88 5.14 5.19 0.89 1.86 1.51 15MTP 16.5 0.88 8.1 8.1 1.76 18.07 1.44 5.1 4.75 1.07 8.4.85 1.88 5.89 5.74 1.0 1.96 1.51 07MTP 19.04 4.7 9.5 9.5 14.85 1.00 15.67 6.44 5.69 1.5 9.7 1.57.5 6.58 6.61 1.6.75 1.81 15MTP 19.90 6.5 9.95 9.95 16.40.0 16.57 7.1 6.70 1.5.51 14.50.75 7.51 7.61 1.7.5. PF PART NO. DIMENSIONS IN INCES Q R RF S SF T TF W WF Y AA M IN. M. OLT SIZE M. OUTPUT ORE 7MTP 4.4 1.18 0.6.77.50.95.8 7.88 1.44.7 4.00 0.00 / 8 1 7/16 58 115MTP 4.51 1.5 0.6 4.6.50 4.56.8 9.14 1.44.1 4.00 0.00 / 8 1 15/16 79 0MTP 5.04 1.48 0.4 5.6.50 5.46.50.94 1.7.64 4.00 0.00 / 8 /16 07MTP 5.57 1.6 0.48 6.08.00 6.9 4.5 1.68.19 4.16 7.00.00 7/16 7/16 16 15MTP 6.4.1 0.48 7.01.00 7. 4.5 14.19.19 4.65 7.00.00 7/16 15/16 4 07MTP 6.79.5 0.61 7.78 4.00 8. 5.8 17.00.78 5.58 9.00 5.00 1/ 7/16 65 15MTP 8.05.6 0.7 8.5 4.75 8.9 6.50 18.1.6 6.0 9.50 5.50 5/ 8 15/16 47 WT. LS. PART NO. DIMENSIONS IN INCES M M N A A4 AC AD NT SPLINE DATA 7MTP 6 SAEA.18 1.60.08 4.19 0.50.5 6 1.00 7MTP 9T SAEA.18 1.60.08 4.19 0.8.5 9 16/.609 7MTP 1T SAE.66.08.56 5.75 5.00 0.50 4.00 1 16/.875 115MTP 6 SAEA.18 1.60.08 4.19 0.50.5 6 1.00 115MTP 9T SAEA.18 1.60.08 4.19 0.8.5 9 16/.609 115MTP 1T SAE.66.08.56 5.75 5.00 0.50 4.00 1 16/.875 0MTP 6 SAEA.68.14.58 4.19 0.50.5 6 1.00 0MTP 9T SAEA.68.14.58 4.19 0.8.5 9 16/.609 0MTP 1T SAE.87..77 5.75 5.00 0.50 4.00 1 16/.875 0MTP 14T SAEC4.18.64 4.08 6.8 0.50 5.00 14 1/4 1.4 07MTP 6 SAEA.6.07.5 4.19 0.50.5 6 1.00 07MTP 1T SAE.81.6.71 5.75 5.00 0.50 4.00 1 16/.875 07MTP 14T SAEC4.1.57 4.0 6.8 0.50 5.00 14 1/4 1.4 15MTP 6 SAEA.69.1.7 4.19 0.50.5 6 1.00 15MTP 1T SAE.68.11.71 5.75 5.00 0.50 4.00 1 16/.875 15MTP 14T SAEC4.4.67 4.7 6.8 0.50 5.00 14 1/4 1.4 07MTP 6 SAEA.9 1.67.65 4.19 0.50.5 6 1.00 07MTP 14T SAEC4.84. 4.0 6.8 0.50 5.00 14 1/4 1.4 15MTP 6 SAEA 1.9 1.9.65 4.19 0.50.5 6 1.00 15MTP 14T SAEC4.47 1.84 4.0 6.8 0.50 5.00 14 1/4 1.4 NT Number of spline teeth. DP Involute spline diametral pitch. OD Internal spline major outside diameter. Part Number Explanation bore in 1/16 increments (7 = 1 7/16 output bore) ydraulic mount TorqTaper Plus Nominal ratio (5:1) ydraulic motor mounting styles DP OD 7 M TP 05 6 SAEA 47

Innovative CFace Motor Connections 48

rowning CFace TorqTaper Plus Shaft Mount Reducers Experience the latest in technology with the new CFace TorqTaper Plus shaft mounted reducers. Emerson engineers continue to create innovative new designs to solve industry needs. CMTP Eliminate belt guards, belt drives and motor mounts Combine with Intelligear for variable speed control Innovative Emerson CFace motor connections Patented mounting system, barrier seal system and increased ratings 1 4 1. Rugged CFace adapters designed for standard NEMA frame sizes. Metal key provides positive torque transmission. Non metallic quill liner eliminates fretting and allows for easier motor removal 4. earing supported quill input minimizes shaft wobble and increases seal life 49

Selection and Ordering Information Example No. 1 Units 7 15 Cface Shaft Mounts A Cface shaft mount reducer is required for a grain bucket elevator, which will be uniformly loaded and operated 8 hours per day at 50. The elevator requires 0 hp. The reducer will be mounted on the elevator drive pulley shaft with a 7/16" diameter extension. 1. Determine the Load Classification From the AGMA Application Classification Numbers section, note the AGMA Class Number is II for a bucket elevator operating to hours per day.. Determine the Speed Reducer Required From the Cface Reducer Selection Chart section, there are two tables for Class II Service. Locate the 50 row in each table. Read across the row to find a column with a rating of 0 hp or greater. Read up the column to determine the basic reducer size that corresponds to the design hp. For this application, a 15CMTP05, 07CMTP09, 07CMTP15, 07CMTP5 or a 07CMTP5 may be used. Generally, the smaller case size is more economical, but the total system should be considered. For this example, select a 07CMTP5. When used with a 1750 Cface motor, the 5:1 ratio will provide an output speed closest to the desired 50 speed. Other ratios may be used, but to obtain the desired speed a variable frequency drive may be required. (Note: The motor and variable frequency drives are not included with the reducer.) From the CMTP Availability Table, locate the row with the basic reducer size. At the top of the table, locate the column with the Cface motor frame designation required. The complete reducer part number is at the intersection of the selected row and column. For this example, a 07CMTP5 Q50 is selected. A 07TP07 bushing is required to mount the reducer to a 7/16 shaft. The 07TAP kit is required to restrain the gearbox in operation.. List Components 1, 07CMTP5 Q50 reducer 1, 07TP07 bushing 1, 07TAP torque arm kit 1, Cface motor purchased separately Refer to CFace standard and stainless steel motors section for product information. Note: See Application Considerations on back cover. 50 CMTP Availability Table PART NO. RATIO Q56 40 80 Q Q50 7CMTP05 5.0588 7CMTP05 Q56 7CMTP05 40 7CMTP09 8.805 7CMTP09 Q56 7CMTP09 40 7CMTP15 14.876 7CMTP15 Q56 7CMTP15 40 7CMTP5 4.750 7CMTP5 Q56 7CMTP5 40 7CMTP5 4.8778 7CMTP5 Q56 7CMTP5 40 115CMTP05 4.7000 115CMTP05 Q56 115CMTP05 40 115CMTP05 80 115CMTP09 8.815 115CMTP09 Q56 115CMTP09 40 115CMTP09 80 115CMTP15 14.7759 115CMTP15 Q56 115CMTP15 40 115CMTP15 80 115CMTP5 4.8558 115CMTP5 Q56 115CMTP5 40 115CMTP5 80 115CMTP5 4.9487 115CMTP5 Q56 115CMTP5 40 115CMTP5 80 0CMTP05 5.5 0CMTP05 Q56 0CMTP05 40 0CMTP05 80 0CMTP05 Q 0CMTP09 8.87 0CMTP09 Q56 0CMTP09 40 0CMTP09 80 0CMTP09 Q 0CMTP15 14.91 0CMTP15 Q56 0CMTP15 40 0CMTP15 80 0CMTP15 Q 0CMTP5 4.7409 0CMTP5 Q56 0CMTP5 40 0CMTP5 80 0CMTP5 Q 0CMTP5 4.649 0CMTP5 Q56 0CMTP5 40 0CMTP5 80 0CMTP5 Q 07CMTP05 5.1579 07CMTP05 Q56 07CMTP05 40 07CMTP05 80 07CMTP05 Q 07CMTP09 8.808 07CMTP09 Q56 07CMTP09 40 07CMTP09 80 07CMTP09 Q 07CMTP15 14.7870 07CMTP15 Q56 07CMTP15 40 07CMTP15 80 07CMTP15 Q 07CMTP5 4.7094 07CMTP5 Q56 07CMTP5 40 07CMTP5 80 07CMTP5 Q 07CMTP5 5.0000 07CMTP5 Q56 07CMTP5 40 07CMTP5 80 07CMTP5 Q 15CMTP05 5.1667 15CMTP05 Q56 15CMTP05 40 15CMTP05 80 15CMTP05 Q 15CMTP05 Q50 15CMTP09 8.848 15CMTP09 Q56 15CMTP09 40 15CMTP09 80 15CMTP09 Q 15CMTP09 Q50 15CMTP15 14.8187 15CMTP15 Q56 15CMTP15 40 15CMTP15 80 15CMTP15 Q 15CMTP15 Q50 15CMTP5 4.850 15CMTP5 Q56 15CMTP5 40 15CMTP5 80 15CMTP5 Q 15CMTP5 Q50 15CMTP5 4.8154 15CMTP5 Q56 15CMTP5 40 15CMTP5 80 15CMTP5 Q 15CMTP5 Q50 07CMTP05 5.1111 07CMTP05 Q56 07CMTP05 40 07CMTP05 80 07CMTP05 Q 07CMTP05 Q50 07CMTP09 8.795 07CMTP09 Q56 07CMTP09 40 07CMTP09 80 07CMTP09 Q 07CMTP09 Q50 07CMTP15 14.9704 07CMTP15 Q56 07CMTP15 40 07CMTP15 80 07CMTP15 Q 07CMTP15 Q50 07CMTP5 4.769 07CMTP5 Q56 07CMTP5 40 07CMTP5 80 07CMTP5 Q 07CMTP5 Q50 07CMTP5 4.8791 07CMTP5 Q56 07CMTP5 40 07CMTP5 80 07CMTP5 Q 07CMTP5 Q50 15CMTP05 4.884 15CMTP05 Q56 15CMTP05 40 15CMTP05 80 15CMTP05 Q 15CMTP05 Q50 15CMTP09 8.860 15CMTP09 Q56 15CMTP09 40 15CMTP09 80 15CMTP09 Q 15CMTP09 Q50 15CMTP15 14.5744 15CMTP15 Q56 15CMTP15 40 15CMTP15 80 15CMTP15 Q 15CMTP15 Q50 15CMTP5 4.4118 15CMTP5 Q56 15CMTP5 40 15CMTP5 80 15CMTP5 Q 15CMTP5 Q50 15CMTP5 4.051 15CMTP5 Q56 15CMTP5 40 15CMTP5 80 15CMTP5 Q 15CMTP5 Q50

Selection and Ordering Information Example No. Units 7 15 Cface Screw Conveyor Drive A Cface shaft mount reducer is required for a screw conveyor transporting rice. The conveyor will be uniformly loaded and operates 18 to 4 hours per day. The screw is 1" diameter and has a " bore with three holes. The conveyor requires 5 hp and will operate at 70. The application requires a waste pack. 1. Determine the Load Classification From the AGMA Application Classification Numbers section, note the AGMA Class Number is II for a uniformly loaded or fed screw conveyor operating over hours per day.. Determine the Speed Reducer Required From the Cface Reducer Selection Chart section, there are two tables for Class II Service. Locate the 70 row in each table. Read across the row to find a column with a rating of 5 hp or greater. Read up the column to determine the basic reducer size that corresponds to the design hp. For this application, a 115CMTP05, 115CMTP09, 115CMTP15 or a 115CMTP5 may be used. For this example, select a 115CMTP5. When used with a 1750 Cface motor, the 5:1 ratio will provide an output speed closest to the desired 70 speed. Other ratios may be used, but to obtain the desired speed a variable frequency drive may be required. (Note: The motor and variable frequency drives are not included with the reducer.) From the CMTP Availability Table, locate the row with the basic reducer size. At the top of the table, locate the column with the Cface motor frame designation required. The complete reducer part number is at the intersection of the selected row and column. For this example, a 115CMTP5 80 is selected.. Establish Sealing Required for Screw Conveyor The waste pack cartridge is well suited for dry materials, such as rice. Specify the optional waste pack cartridge for the 115 shaft mount selected. From the Accessories section, select part 1150WPP. 4. Select the Screw Conveyor Adapter and Screw Conveyor Shaft CMTP Exact Ratios Reducer 7 15 0 07 15 07 15 Using the basic reducer size, required drive shaft and screw diameter for the selection; refer to Screw Conveyor Drives in the Accessories section. Note the specification was for a " drive shaft with a three hole arrangement for the 1" diameter screw. From the table select the 115SCAP and the 115DSP00. 5. Select the Trough End From the Screw Conveyor Trough Ends s 7407 table, select the SCTE1 X trough end. 6. List of Components: 1, 115CMTP5 80 reducer 1, 115SCAP screw conveyor adapter 1, 115DSP00 screw conveyor drive shaft kit 1, 1150WPP waste pack cartridge 1, SCTE1X trough end 1, Cface motor (separate) Ratio Symbols 05 09 15 5 5 5.058 8.805 14.876 4.750 1 8 4.7000 8.815 14.7759 4.8558 5.5 5.1579 5.1667 5.111 4.884 1 8.87 8.808 8.848 8.795 8.860 Refer to CFace standard and stainless steel motors section for product information. 14.91 14.7870 14.8187 14.9704 14.5744 4.7409 4.7094 4.850 4.769 4.4118 4.8778 4.9487 4.649 5.0000 4.8154 4.8791 4.051 CMTP Note: See Application Considerations on back cover. 51

5 Application AGMA Class Numbers Up to ours Per Day ours Per Day Over ours Per Day AGITATORS (Mixers) Pure Liquids I I II Liquids and Solids I II II Liquids Variable Density I II II LOWERS Centrifugal & Vane I I II Lobe I II II Vane I II II REWING AND DISTILLING ottling Machinery I I II rew Kettles Continuous Duty II II II Cookers Continuous Duty II II II Mash Tubs Continuous Duty II II II Scale opper Frequent Starts II II II CAN FILLING MACINES I I II CAR DUMPERS II III III CAR PULLERS I II II CLARIFIERS I I II CLASSIFIERS I II II CLAY WORKING MACINERY rick Presses II III III riquette Machines II III III Pug Mills I II II COMPACTORS COMPRESSORS Centrifugal I I II Lobe I II II Reciprocating, MultiCylinder II II III Reciprocating, SingleCylinder III III III CONVEYORS GENERAL PURPOSE Includes Apron, Assembly, elt, ucket Chain, Flight, Oven, and Screw Uniformly Loaded or Fed I I II eavy Duty Not Uniformly Fed I II II Severe Duty Reciprocating or Shaker II III III CRANES Dry Dock Main oist Auxiliary oist oom oist Slewing Drive Traction Drive Container Main oist oom oist Trolley Drive Gantry Drive Traction Drive Mill Duty Main oist Auxiliary ridge Travel Trolley Travel Industrial Duty Main Auxiliary ridge Travel Trolley Travel CRUSERS Stone or Ore III III III DREDGES Cable Reels II II II Conveyors II II II Cutter ead Drives III III III Pumps III III III Screen Drives III III III Stackers II II II Winches II II II ELEVATORS ucket I II II Centrifugal Discharge I I II Escalators I I II Freight I II II Gravity Discharge I I II EXTRUDERS General II II II Plastics Variable Speed Drive III III III Speed Drive III III III Rubber Continuous Screw Operation III III III Intermittent Screw Operation III III III FANS Centrifugal I I II AGMA Application Classification Numbers Application AGMA Class Numbers Up to ours Per Day ours Per Day Over ours Per Day FANS (Cont d) Cooling Towers III III III Forced Draft II II II Induced Draft II II II Industrial & Mine II II II FEEDERS Apron I II II elt I II II Disc I I II Reciprocating II III III Screw I II II FOOD INDUSTRY Cereal Cooker I I II Dough Mixer II II II Meat Grinders II II II Slicers I II II GENERATORS AND EXCITERS II II II AMMER MILLS III III III OISTS eavy Duty Medium Duty Skip oist LAUNDRY TUMLERS II II II LAUNDRY WASERS II II III LUMER INDUSTRY arkers Spindle Feed II II II Main Drive III III III Conveyors urner II II II Main or eavy Duty II II II Main Log III III III Resaw, MerryGoRound II II II Slab III III III Transfer II II II Chains Floor II II II Green II II III CutOffSaws Chain II II III Drag II II III Debarking Drums III III III Feeds Edger II II II Gang II III III Trimmer II II II Log Deck III III III Log auls Incline Well Type III III III Log Turning Devices III III III Planer Feed II II II Planer Tilting oists II II II Rolls LiveOff rg Roll Cases III III III Sorting Table II II II Tipple oist II II II Transfer Chain II II III Craneway II II III Tray Drives II II II Veneer Lathe Drives II II II METAL MILLS Draw ench Carriage and Main Drive II II II Runout Table NonReversing Group Drives II II II Individual Drives III III III Reversing III III III Slab Pushers II II II Shears III III III Wire Drawing II II II Wire Winding Machine II II II METAL STRIP PROCESSING MACINERY ridges II II II Collers & Uncoilers I I II Edge Trimmers I II II Flatteners II II II Loopers (Accumulators) I I I Pinch Rolls II II II Scrap Choppers II II II Shears III III III Slitters I II II MILLS, ROTARY TYPE all & Rod Spur Ring Gear III III III elical Ring Gear II II II Direct Connected III III III

CMTP Selection Chart Class I Service (1.0 S.F.) RPM Single Reduction 7CMTP05 115CMTP05 0CMTP05 07CMTP05 15CMTP05 07CMTP05 15CMTP05 (Inlbs) (Inlbs) (Inlbs) (Inlbs) (Inlbs) (Inlbs) (Inlbs) 5 0.6,184 0.5 6, 0.85,4 1.04 1,555 1.6 19,71.45 9,661.14 8,06 0.5,184 1.04 6, 1.71,4.08 1,555.6 19,71 4.90 9,661 6.8 8,06 0 1.05,184.09 6,.41,4 4.15 1,555 6.5 19,71 9.80 9,661 1.57 8,06 0 1.58,184.1 6, 5.1,4 6. 1,555 9.78 19,71 14.71 9,661 18.85 8,06 40.11,184 4.17 6, 6.8,4 8.0 1,555 1.04 19,71 19.61 9,661 5.14 8,06 50.6,184 5.1 6, 8.5,4.8 1,555 16.0 19,71 4.51 9,661 1.4 8,06 60.16,184 6.6 6,.4,4 1.45 1,555 19.56 19,71 9.41 9,661 7.71 8,06 70.68,184 7.0 6, 11.94,4 14.5 1,555.8 19,71 4. 9,661 4.99 8,06 80 4.1,184 8.4 6, 1.65,4 16.60 1,555 6.08 19,71 9. 9,661 50.8 8,06 90 4.74,184 9.9 6, 15.6,4 18.68 1,555 9.4 19,71 44.1 9,661 7,815 0 5.09,081. 6,1 16.5 9,996 0.07 1,145 1.4 18,959 8,61 4,04 1 5.44,990.79 5,95 17.65 9,707 1.44 11,795.41 18,74 5,78 0,940 5.77,9 11.46 5,779 18.75 9,451.78 11,484 5.40 17,850,64 8,61 6.,87 1.11 5,68 19.81 9,1 4.08 11,07 7.5 17,8 1,816 6,180 140 6.41,77 1.75 5,51 0.86 9,014 5.4,95 7.50 16,06 0,58 4, 150 6.7,71 1.8 5,97 0.9 8,440 6.58,7 7.50 15,16 18,908,689 160 7.0,657 1.99 5,90 0.9 7,91 7.80,514 7.50 14,181 17,76 1,71 170 7.,607 14.59 5,19 0.9 7,447 8.99,19 7.50 1,46 16,68 0,00 180 7.6,561 15.18 5,4 0.9 7,04 0.17,14 7.50 1,605 15,756 18,908 190 7.91,517 15.19 4,86 0.9 6,66 1. 9,975 7.50 11,94 14,97 17,91 00 8.19,477 15.19 4,595 0.9 6,0.45 9,817 7.50 11,45 14,181 17,017 8.46,49 15.19 4,76 0.9 6,09.81 9,454 7.50,804 1,505 16,06 0 8.74,40 15.19 4,177 0.9 5,755.81 9,04 7.50,1 1,891 15,470 0 9.01,69 15.19,995 0.9 5,505.81 8,6 7.50 9,865 1,1 14,797 40 9.7,7 15.19,89 0.9 5,75.81 8,7 7.50 9,454 11,817 14,181 50 9.5,07 15.19,676 0.9 5,064.81 7,941 7.50 9,076 11,45 1,61 60 9.79,78 15.19,54 0.9 4,869.81 7,66 7.50 8,77,908 1,090 70.05,51 15.19,40 0.9 4,689.81 7,5 7.50 8,40,504 1,605 80.0,5 15.19,8 0.9 4,5.81 7,090 7.50 8,,19 1,155 90.55,00 15.19,169 0.9 4,66.81 6,846 7.50 7,84 9,780 11,76 00.79,176 15.19,06 0.9 4,0.81 6,618 7.50 7,56 9,454 11,45 11.04,154 15.19,964 0.9 4,084.81 6,404 7.50 7,19 9,149,979 0 11.8,1 15.19,87 0.9,956.81 6,04 7.50 7,090 8,86,65 0 11.5,111 15.19,785 0.9,87.81 6,016 7.50 6,875 8,594,1 40 11.75,091 15.19,70 0.9,74.81 5,89 7.50 6,67 8,4,0 50 11.81,04 15.19,65 0.9,617.81 5,67 7.50 6,48 8, 9,74 60 11.81 1,985 15.19,55 0.9,517.81 5,515 7.50 6,0 7,878 9,454 70 11.81 1,9 15.19,484 0.9,4.81 5,66 7.50 6,1 7,665 9,198 80 11.81 1,881 15.19,418 0.9,.81 5,4 7.50 5,971 7,46 8,956 90 11.81 1,8 15.19,56 0.9,46.81 5,090 7.50 5,818 7,7 8,77 400 11.81 1,787 15.19,97 0.9,165.81 4,96 7.50 5,67 7,090 8,508 54

CMTP Selection Chart Class I Service (1.0 S.F.) RPM 7CMTP09 7CMTP15 7CMTP5 7CMTP5 (Inlbs) 115CMTP09 115CMTP15 115CMTP5 115CMTP5 (Inlbs) 0CMTP09 0CMTP15 0CMTP5 0CMTP5 (Inlbs) Double Reduction 07CMTP09 07CMTP15 07CMTP5 07CMTP5 (Inlbs) 15CMTP09 15CMTP15 15CMTP5 15CMTP5 (Inlbs) 07CMTP09 07CMTP15 07CMTP5 07CMTP5 (Inlbs) 15CMTP09 15CMTP15 15CMTP5 15CMTP5 (Inlbs) 5 0.50 6,081 0.70 8,516 1. 14,760 1.9,48.11 7,659 5.19 6,791 5.76 69,69 0.97 5,85 1.1 7,919.7 1,718.58 1,689 5.8 5,41.05 60,784 11.5 69,69 0 1.86 5,6.51 7,594 4.4 1,11 6.86 0,750 11.09,554 19.4 58,06.04 69,69 0.7 5,48.71 7,49 6.41 1,97.14 0,450 16.9,05 8.09 56,660 4.56 69,69 40.56 5,84 4.90 7,415 8.46 1,798 1.7 0, 1.60,671 6.0 54,904 46.07 69,69 50 4.8 5,05 6.08 7,5.48 1,685 16.56 0,07 6.74,60 4.4 51,49 68,067 60 5.0 5,40 7.4 7,98 1.48 1,588 19.19 19,5 1.77,08 47,69 56,7 70 6.00 5,184 8.9 7,51 1.76 11,89 1.8 18,477 5.9 0,588 40,516 48,619 80 6.79 5,15 9.5 7,09 14.95 11,07.47 17,75 7.50 8,61 5,45 4,54 90 7.57 5,09.67 7,171 16.09,815 5.49 17,16 7.50 5, 1,51 7,815 0 8.5 5,05 11.80 7,17 17.17,90 7.44 16,60 7.50,689 8,61 4,04 1 9.1 5,017 1.9 7,4 18.0,066 9. 16,14 7.50 0,66 5,78 0,940 9.88 4,984 14.0 7,074 19.40 9,779 1.18 15,719 7.50 18,908,64 8,61.64 4,95 15.14 7,046 0.46 9,51.81 15,71 7.50 17,45 1,816 6,180 140 11.40 4,95 15.19 6,564 0.9 9,04.81 14,181 7.50 16,06 0,58 4, 150 11.81 4,765 15.19 6,16 0.9 8,440.81 1,5 7.50 15,16 18,908,689 160 11.81 4,467 15.19 5,74 0.9 7,91.81 1,408 7.50 14,181 17,76 1,71 170 11.81 4,04 15.19 5,405 0.9 7,447.81 11,678 7.50 1,46 16,68 0,00 180 11.81,971 15.19 5,5 0.9 7,04.81 11,09 7.50 1,605 15,756 18,908 190 11.81,76 15.19 4,86 0.9 6,66.81,449 7.50 11,94 14,97 17,91 00 11.81,574 15.19 4,595 0.9 6,0.81 9,96 7.50 11,45 14,181 17,017 CMTP 55

CMTP Selection Chart Class II Service (1.4 S.F.) RPM Single Reduction 7CMTP05 115CMTP05 0CMTP05 07CMTP05 15CMTP05 07CMTP05 15CMTP05 (Inlbs) (Inlbs) (Inlbs) (Inlbs) (Inlbs) (Inlbs) (Inlbs) 5 0.19,74 0.7 4,507 0.61 7,74 0.74 8,968 1.16 14,087 1.75 1,187.4 7,16 0.8,74 0.74 4,507 1. 7,74 1.48 8,968. 14,087.50 1,187 4.49 7,16 0 0.75,74 1.49 4,507.44 7,74.96 8,968 4.66 14,087 7.00 1,187 8.98 7,16 0 1.1,74. 4,507.66 7,74 4.45 8,968 6.98 14,087.51 1,187 1.47 7,16 40 1.50,74.98 4,507 4.88 7,74 5.9 8,968 9.1 14,087 14.01 1,187 17.96 7,16 50 1.88,74.7 4,507 6.09 7,74 7.41 8,968 11.64 14,087 17.51 1,187.45 7,16 60.6,74 4.47 4,507 7.1 7,74 8.89 8,968 1.97 14,087 1.01 1,187 6.94 7,16 70.6,74 5.1 4,507 8.5 7,74.8 8,968 16.0 14,087 4.51 1,187 1.4 7,16 80.01,74 5.96 4,507 9.75 7,74 11.86 8,968 18.6 14,087 8.01 1,187 5.91 7,16 90.8,74 6.70 4,507.97 7,74 1.4 8,968 0.95 14,087 1.5 1,187 40.40 7,16 0.64,01 7.1 4,64 11.80 7,140 14.4 8,675.8 1,54.68 0,76 4.46 6,94 1.88,16 7.71 4,9 1.61 6,94 15. 8,45.86 1,15 5.89 19,74 46.45 5,548 4.1,078 8.19 4,18 1.9 6,751 16.7 8,0 5.9 1,750 8.07 19,194 49.4 4,879 4.5,07 8.65 4,07 14.15 6,587 17.0 8,005 6.68 1,416 40.15 18,688 5.15 4,74 140 4.58 1,980 9.11,97 14.90 6,48 18. 7,8 8.0 1,11 4.19 18,4 54.9,78 150 4.80 1,97 9.56,855 15.6 6,0 18.99 7,659 9.5 11,89 44.18 17,81,689 160 5.0 1,898 9.99,779 16.4 6,179 19.86 7,5 0.64 11,585 46.1 17,441 1,71 170 5. 1,86.4,7 17.04 6,06 0.71 7,70 1.89 11,51 16,68 0,00 180 5.44 1,89.85,646 17.7 5,958 1.55 7,44.1 11,16 15,756 18,908 190 5.65 1,798 11.6,585 18.40 5,860.7 7,15 4.4,97 14,97 17,91 00 5.85 1,769 11.67,59 19.07 5,768.18 7,01 5.5,748 14,181 17,017 6.05 1,74 1.07,477 19.7 5,681.97 6,906 6.69,57 1,505 16,06 0 6.4 1,716 1.46,48 0.6 5,600 4.76 6,808 7.50,1 1,891 15,470 0 6.4 1,69 1.85,80 0.9 5,505 5.54 6,718 7.50 9,865 1,1 14,797 40 6.6 1,669 1.,6 0.9 5,75 6.9 6,68 7.50 9,454 11,817 14,181 50 6.81 1,648 1.6,96 0.9 5,064 7.04 6,545 7.50 9,076 11,45 1,61 60 6.99 1,67 1.99,56 0.9 4,869 7.79 6,467 7.50 8,77,908 1,090 70 7.18 1,608 14.6,18 0.9 4,689 8.5 6,9 7.50 8,40,504 1,605 80 7.5 1,589 14.7,18 0.9 4,5 9.7 6,4 7.50 8,,19 1,155 90 7.5 1,57 15.09,148 0.9 4,66 9.98 6,54 7.50 7,84 9,780 11,76 00 7.71 1,555 15.19,06 0.9 4,0 0.69 6,189 7.50 7,56 9,454 11,45 7.88 1,59 15.19,964 0.9 4,084 1.40 6,18 7.50 7,19 9,149,979 0 8.06 1,5 15.19,87 0.9,956.09 6,068 7.50 7,090 8,86,65 0 8. 1,508 15.19,785 0.9,87.76 6,007 7.50 6,875 8,594,1 40 8.9 1,494 15.19,70 0.9,74.81 5,89 7.50 6,67 8,4,0 50 8.56 1,480 15.19,65 0.9,617.81 5,67 7.50 6,48 8, 9,74 60 8.7 1,467 15.19,55 0.9,517.81 5,515 7.50 6,0 7,878 9,454 70 8.89 1,454 15.19,484 0.9,4.81 5,66 7.50 6,1 7,665 9,198 80 9.05 1,441 15.19,418 0.9,.81 5,4 7.50 5,971 7,46 8,956 90 9. 1,40 15.19,56 0.9,46.81 5,090 7.50 5,818 7,7 8,77 400 9.7 1,418 15.19,97 0.9,165.81 4,96 7.50 5,67 7,090 8,508 56

CMTP Selection Chart Class II Service (1.4 S.F.) RPM 7CMTP09 7CMTP15 7CMTP5 7CMTP5 (Inlbs) 115CMTP09 115CMTP15 115CMTP5 115CMTP5 (Inlbs) 0CMTP09 0CMTP15 0CMTP5 0CMTP5 (Inlbs) Double Reduction 07CMTP09 07CMTP15 07CMTP5 07CMTP5 (Inlbs) 15CMTP09 15CMTP15 15CMTP5 15CMTP5 (Inlbs) 07CMTP09 07CMTP15 07CMTP5 07CMTP5 (Inlbs) 15CMTP09 15CMTP15 15CMTP5 15CMTP5 (Inlbs) 5 0.6 4,4 0.50 6,08 0.87,54 1.8 16,677. 6,899.71 44,851 4.11 49,780 0.69 4,181 0.9 5,656 1.6 9,798.56 15,49 4.16 5,17 7.18 4,417 8. 49,780 0 1. 4,016 1.79 5,45. 9,7 4.90 14,8 7.9,967 1.74 41,576 16.46 49,780 0 1.94,917.65 5,5 4.58 9,41 7.4 14,607 11.71,609 0.07 40,471 4.68 49,780 40.54,845.50 5,96 6.04 9,14 9.55 14,445 15.4,7 5.9 9,17.91 49,780 50.1,789 4.4 5,51 7.49 9,060 11.8 14,1 19.,114 0.1 6,678 41.14 49,780 60.71,74 5.17 5,1 8.9 8,991 1.71 1,8.69,884 4.44 4,75 48.86 49,69 70 4.8,70 5.99 5,179 9.8 8,494 15.7 1,198 5.8 1,849 8.6,156 48,619 80 4.85,668 6.81 5,149.68 8,077 16.77 1,680 7.76 0,99 4.1 1,855 4,54 90 5.41,67 7.6 5,1 11.49 7,75 18.1 1,40 0.14 0,6 45.74 0,747 7,815 0 5.96,609 8.4 5,098 1.7 7,41 19.60 11,858.45 19,6 8,61 4,04 1 6.51,58 9. 5,075 1.07 7,190 0.95 11,54 4.69 19,078 5,78 0,940 7.06,560.0 5,05 1.85 6,985.7 11,8 6.87 18,588,64 8,61 7.60,58.81 5,0 14.61 6,801.55,961 7.50 17,45 1,816 6,180 140 8.14,518 11.60 5,014 15.5 6,65 4.80,70 7.50 16,06 0,58 4, 150 8.67,499 1. 4,971 16.07 6,48 6.0,501 7.50 15,16 18,908,689 160 8.84,4 1.89 4,875 16.78 6,44 7.4,99 7.50 14,181 17,76 1,71 170 9.0,7 1.45 4,788 17.46 6,15 8.4,11 7.50 1,46 16,68 0,00 180 9.55,09 14.00 4,706 18.14 6,097 9.57 9,941 7.50 1,605 15,756 18,908 190 9.89,149 14.54 4,61 18.80 5,986 0.71 9,781 7.50 11,94 14,97 17,91 00.,094 15.07 4,560 19.45 5,884 1.84 9,6 7.50 11,45 14,181 17,017 CMTP 57

CMTP Selection Chart Class III Service (.0 S.F.) RPM Single Reduction 7CMTP05 115CMTP05 0CMTP05 07CMTP05 15CMTP05 07CMTP05 15CMTP05 (Inlbs) (Inlbs) (Inlbs) (Inlbs) (Inlbs) (Inlbs) (Inlbs) 5 0.1 1,59 0.6,155 0.4 5,16 0.5 6,78 0.81 9,861 1. 14,81 1.57 19,01 0.6 1,59 0.5,155 0.85 5,16 1.04 6,78 1.6 9,861.45 14,81.14 19,01 0 0.5 1,59 1.04,155 1.71 5,16.08 6,78.6 9,861 4.90 14,81 6.8 19,01 0 0.79 1,59 1.56,155.56 5,16.11 6,78 4.89 9,861 7.5 14,81 9.4 19,01 40 1.05 1,59.09,155.41 5,16 4.15 6,78 6.5 9,861 9.80 14,81 1.57 19,01 50 1. 1,59.61,155 4.7 5,16 5.19 6,78 8.15 9,861 1.6 14,81 15.71 19,01 60 1.58 1,59.1,155 5.1 5,16 6. 6,78 9.78 9,861 14.71 14,81 18.85 19,01 70 1.84 1,59.65,155 5.97 5,16 7.6 6,78 11.41 9,861 17.16 14,81.00 19,01 80.11 1,59 4.17,155 6.8 5,16 8.0 6,78 1.04 9,861 19.61 14,81 5.14 19,01 90.7 1,59 4.69,155 7.68 5,16 9.4 6,78 14.67 9,861.06 14,81 8.8 19,01 0.55 1,540 5.05,055 8.6 4,998.04 6,07 15.67 9,480.57 14,6 0.4 18,406 1.7 1,495 5.9,967 8.8 4,85.7 5,898 16.70 9,187 5.1 1,80.51 17,884.89 1,455 5.7,889 9.7 4,76 11.9 5,74 17.70 8,95 6.65 1,46 4.54 17,415.05 1,419 6.06,819 9.91 4,611 1.04 5,60 18.67 8,691 8.11 1,08 6.51 16,991 140.1 1,86 6.8,756.4 4,507 1.67 5,476 19.6 8,479 9.5 1,764 8.45 16,617 150.6 1,56 6.69,698.94 4,41 1.9 5,61 0.55 8,87 0.9 1,475 40. 16,66 160.51 1,9 7.00,645 11.44 4,5 1.90 5,57 1.44 8,9.9 1,09 4.0 15,957 170.66 1,04 7.0,597 11.9 4,44 14.50 5,159. 7,946.6 11,967 44.00 15,659 180.81 1,80 7.59,55 1.41 4,170 15.09 5,071.19 7,796 4.9 11,74 45.79 15,91 190.95 1,59 7.88,509 1.88 4, 15.66 4,987 4.04 7,656 6.19 11,54 47.5 15,16 00 4.09 1,8 8.17,470 1.5 4,08 16. 4,908 4.87 7,54 7.47 11,5 49.4 14,897 4. 1,19 8.45,44 1.80,977 16.78 4,84 5.69 7,401 8.68 11,145 50.99 14,690 0 4.7 1,01 8.7,99 14.5,90 17. 4,766 6.49 7,86 9.90,97 5.66 14,48 0 4.50 1,185 9.00,66 14.70,866 17.88 4,70 7.9 7,178 41.,81 54.5 14,7 40 4.6 1,168 9.6,5 15.14,816 18.40 4,69 8.07 7,076 4.9,66 55.9 14,099 50 4.77 1,15 9.5,07 15.57,768 18.9 4,58 8.8 6,976 4.4,509 1,61 60 4.89 1,19 9.79,79 16.00,7 19.45 4,57 9.58 6,88 44.55,68 1,090 70 5.0 1,16.05,5 16.4,679 19.97 4,475 0.4 6,798 45.69,8 1,605 80 5.15 1,11.1,7 16.84,68 0.49 4,47 1.06 6,71 46.8, 1,155 90 5.7 1,0.56,0 17.5,599 0.98 4,78 1.79 6,6 9,780 11,76 00 5.40 1,088.81,180 17.66,561 1.48 4,.51 6,558 9,454 11,45 5.5 1,077 11.06,159 18.06,55 1.98 4,90.1 6,48 9,149,979 0 5.64 1,066 11.1,18 18.46,490.46 4,47.9 6,414 8,86,65 0 5.76 1,056 11.55,117 18.85,457.9 4,05 4.61 6,46 8,594,1 40 5.88 1,046 11.79,099 19.5,45.41 4,166 5.0 6,8 8,4,0 50 5.99 1,06 1.0,080 19.64,95.89 4, 5.97 6,18 8, 9,74 60 6.11 1,07 1.6,061 0.0,65 4.6 4,095 6.64 6,158 7,878 9,454 70 6. 1,018 1.50,044 0.40,7 4.8 4,059 7. 6, 7,665 9,198 80 6.4 1,009 1.7,08 0.78,08 5.9 4,07 7.50 5,971 7,46 8,956 90 6.45 1,001 1.96,011 0.9,46 5.75,995 7.50 5,818 7,7 8,77 400 6.56 99 1.19 1,995 0.9,165 6.0,96 7.50 5,67 7,090 8,508 58

CMTP Selection Chart Class III Service (.0 S.F.) RPM 7CMTP09 7CMTP15 7CMTP5 7CMTP5 (Inlbs) 115CMTP09 115CMTP15 115CMTP5 115CMTP5 (Inlbs) 0CMTP09 0CMTP15 0CMTP5 0CMTP5 (Inlbs) Double Reduction 07CMTP09 07CMTP15 07CMTP5 07CMTP5 (Inlbs) 15CMTP09 15CMTP15 15CMTP5 15CMTP5 (Inlbs) 07CMTP09 07CMTP15 07CMTP5 07CMTP5 (Inlbs) 15CMTP09 15CMTP15 15CMTP5 15CMTP5 (Inlbs) 5 0.5,040 0.5 4,58 0.61 7,80 0.96 11,674 1.56 18,80.59 1,96.88 4,846 0.48,97 0.65,959 1.1 6,859 1.79,845.91 17,61 5.0 0,9 5.76 4,846 0 0.9,811 1.6,797.17 6,561.4,75 5.55 16,777 9.6 9, 11.5 4,846 0 1.6,74 1.86,746.1 6,469 5.07,5 8.19 16,56 14.05 8,0 17.8 4,846 40 1.78,69.45,707 4. 6,99 6.68,111.80 16,6 18.15 7,45.04 4,846 50.19,65.04,676 5.4 6,4 8.8,019 1.7 16,180 1. 5,675 8.80 4,846 60.60,60.6,649 6.4 6,94 9.60 9,676 15.89 16,019 4.11 4,08 4.0 4,488 70.00,59 4.19,66 6.88 5,946.69 9,8 17.69 15,94 6.85,09 9.4 4,071 80.40,568 4.77,605 7.48 5,654 11.74 8,876 19.4 14,695 9.48,98 44.57,708 90.79,546 5.,586 8.04 5,407 1.74 8,568 1. 14,184.0 1,5 47.6,019 0 4.18,56 5.90,568 8.59 5,195 1.7 8,01.71 1,74 4.47 0,854 51.19 0,97 1 4.56,508 6.46,55 9.15 5,0 14.67 8,067 4.8 1,55 6.84 0,66 54.64 0,05 4.94,49 7.0,57 9.70 4,890 15.59 7,860 5.81 1,01 9.16 19,744 8,61 5.,477 7.57,5. 4,761 16.49 7,67 7.9 1,70 41.41 19,74 6,180 140 5.70,46 8.1,5.75 4,644 17.6 7,504 8.75 1,4 4.6 18,85 4, 150 6.07,449 8.6,480 11.5 4,58 18. 7,51 0.17 1,169 45.78 18,466,689 160 6.19,9 9.0,41 11.74 4,441 19.07 7, 1.56 11,96 17,76 1,71 170 6.44,91 9.4,51 1. 4,51 19.89 7,079.9 11,71 16,68 0,00 180 6.68,46 9.80,94 1.70 4,68 0.70 6,959 4.8 11,5 15,756 18,908 190 6.9,04.18,4 1.16 4,190 1.50 6,847 5.60 11,5 14,97 17,91 00 7.16,166.55,19 1.61 4,119.9 6,74 6.90 11,16 14,181 17,017 CMTP 59

Shaft Mount Reducers CMTP TorqTaper Plus Unit s 715 R S T W Reversible single bushing system mounted on the back side. Y 90 Reversible single bushing system mounted on the front side. 60

Shaft Mount Reducers CMTP TorqTaper Plus Unit s 715 PART NO. DIMENSIONS IN INCES A C D E F G 1 J K L M M MC N O P P1 7CMTP 9.76 1.07 4.88 4.88 7.19.07 7.75.5.00 0.6 5.5 7.89.18.61 1.75 4.08 4.5 0.90 1.84 1.14 115CMTP 11.00 14.08 5.50 5.50 8.58 11.78 8.69 4.1.50 0.75 5.99 8.6.4.77 1.88 4.4 4.48 0.90 1.8 1.14 0CMTP 1.88 16.16 6.44 6.44 9.7 1.66.8 4.50.75 0.87 7.07 9.4 4.4,84 1.88 5.1 5.01 0.89 1.8 1. 07CMTP 14.50 16.47 7.5 7.5 11. 15.7 11.76 4.88 4.5 1.01 7.9 9.75 4..65 1.88 5.1 5.14 0.89 1.86 1.51 15CMTP 16.5 0.88 8.1 8.1 1.76 18.07 1.44 5.1 4.75 1.07 8.4.85 4.85 4.8 1.88 5.87 5.89 1.0 1.96 1.51 07CMTP 19.04 4.7 9.5 9.5 14.85 1.00 15.67 6.44 5.69 1.5 9.7 1.57 6.09 5.47.5 7.45 6.58 1.6.75 1.81 15CMTP 19.90 6.5 9.95 9.95 16.40.0 16.57 7.1 6.70 1.5.51 14.50 6.59 5.96.75 8. 7.51 1.7.5. PF CMTP PART NO. DIMENSIONS IN INCES Q R RF S SF T TF U1 W WF Y AA M IN. M. OLT SIZE KEY M. OUTPUT ORE 7CMTP 4.4 1.18 0.6.77.50.95.8 0.75 7.88 1.44.7 4.00 0.00 / 8. 188 x.188 x.88 1 7/16 61 115CMTP 4.51 1.5 0.6 4.6.50 4.56.8 1.1 9.14 1.44.1 4.00 0.00 / 8. 50 x.50 x.75 1 15/16 9 0CMTP 5.04 1.48 0.4 5.6.50 5.46.50 1.5.94 1.7.64 4.00 0.00 / 8. 50 x.50 x.75 /16 07CMTP 5.57 1.6 0.48 6.08.00 6.9 4.5 1.44 1.68.19 4.16 7.00.00 7/16. 75 x.75 x.75 7/16 171 15CMTP 6.4.1 0.48 7.01.00 7. 4.5 1.88 14.19.19 4.65 7.00.00 7/16. 500 x.500 x.75 15/16 50 07CMTP 6.79.5 0.61 7.78 4.00 8. 5.8.00 17.00.78 5.58 9.00 5.00 1/. 500 x.500 x 6.50 7/16 81 15CMTP 8.05.6 0.7 8.5 4.75 8.9 6.50.1 18.1.6 6.0 9.50 5.50 5/ 8. 500 x.500 x 7.50 15/16 490 PART NO. DIMENSIONS IN INCES M M N O U1 KEY A AC AD 7CMTP Q56.41. 0.6 0.188 5.88 0.8 4.50 7CMTP 40.41. 0.88 0.188 5.88 0.8 4.50 115CMTP Q56.41. 0.6 0.188 5.88 0.8 4.50 115CMTP 40.41. 0.88 0.188 5.88 0.8 4.50 115CMTP 80 4.70 5.61 1.1 0.50 7.5 0.50 8.50 0CMTP Q56.9.8.8 4.99 0.6 0.188 5.88 0.8 4.50 0CMTP 40.9.8.8 4.99 0.88 0.188 5.88 0.8 4.50 0CMTP 80 4.71 5.61 1.1 0.50 7.5 0.50 8.50 0CMTP Q 4.71 5.61 1.8 0.1 7.5 0.50 8.50 07CMTP Q56.86.1.76 5.19 0.6 0.188 5.88 0.8 4.50 07CMTP 40.86.1.76 5.19 0.88 0.188 5.88 0.8 4.50 07CMTP 80 4.65 4. 5.55 5.19 1.1 0.50 7.5 0.50 8.50 07CMTP Q 4.65 4. 5.55 5.19 1.8 0.1 7.5 0.50 8.50 15CMTP Q56.80..8 5.74 0.6 0.188 5.88 0.8 4.50 15CMTP 40.80..8 5.74 0.88 0.188 5.88 0.8 4.50 15CMTP 80 4.8 4.6 5.86 5.74 1.1 0.50 7.5 0.50 8.50 15CMTP Q 4.8 4.6 5.86 5.74 1.8 0.1 7.5 0.50 8.50 15CMTP Q50 4.8 4.6 5.86 5.74 1.6 0.75 7.5 0.50 8.50 07CMTP Q56.40 1.78.76 6.61 0.6 0.188 5.88 0.8 4.50 07CMTP 40.40 1.78.76 6.61 0.88 0.188 5.88 0.8 4.50 07CMTP 80 4.4.81 5.79 6.61 1.1 0.50 7.5 0.50 8.50 07CMTP Q 4.4.81 5.79 6.61 1.8 0.1 7.5 0.50 8.50 07CMTP Q50 4.4.81 5.79 6.61 1.6 0.75 7.5 0.50 8.50 15CMTP Q56.0 1.40.76 7.61 0.6 0.188 5.88 0.8 4.50 15CMTP 40.0 1.40.76 7.61 0.88 0.188 5.88 0.8 4.50 15CMTP 80 4.06.4 5.79 7.61 1.1 0.50 7.5 0.50 8.50 15CMTP Q 4.06.4 5.79 7.61 1.8 0.1 7.5 0.50 8.50 15CMTP Q50 4.06.4 5.79 7.61 1.6 0.75 7.5 0.50 8.50 WT. LS. Part Number Explanation bore in 1/16" increments (7 = 1 7/16" output bore) CFace mount TorqTaper Plus Nominal ratio (5:1) Quill motor mounting styles ushing system cannot be mounted on the front side with this reducer and motor combination. 7 CM TP 05 Q56 61

1 4 5 6

6 Check Out These Options for TorqTaper Plus Reducers 1. Modular screw conveyor standard shaft mount converts to a screw conveyor drive using stock components.. ackstop kits. Patented bushing kits 4. elt guard kits 5. ushing guard kits 6. Motor mount kits Shaft Mount Accessories 6

Accessories Type SMTP, MTP, CMTP TorqTaper Plus ushing Kits Unit s 7115 Width Stabilizer Ring External Key Furnished Key Furnished Type 1 Type REDUCER SIZE 7SMTP USING NO. ORE SIZE SAFT KEYSEAT REQUIRED TYPE 7TP01 / 4 /16 x / x 7/ 8 1 STAILIZER RING WIDT OLT TORQUE OLT SIZE FT.LS. WEIGT 7TP014 7/ 8 /16 x / x 7/ 8 1. 5 7TP015 15/16 1/4 x 1/8 x 7/ 8. 4 7TP0 1 1/4 x 1/8 x 7/ 8. 7TP1 1 1/16 1/4 x 1/8 x 7/ 8. 1 0.79 5/1618 x 1 1/ 4 16 7TP 1 1/ 8 1/4 x 1/8 x 7/ 8. 0 7TP 1 /16 1/4 x 1/8 x 7/ 8 1. 9 7TP4 1 1/ 4 1/4 x 1/8 x 7/ 8 1. 8 7TP5 1 5/16 5/16 x 5/ x 7/ 8 1. 6 7TP6 1 / 8 5/16 x 5/ x 7/ 8 1. 5 7TP7 1 7/16 /8 x /16 x 7/ 8 1. 5.6 115TP015 15/16 1/4 x 1/8 x 4 1/ 8 1 6.0 115TP0 1 1/4 x 1/8 x 4 1/ 8 1 5. 9 115TP1 1 1/16 1/4 x 1/8 x 4 1/ 8 1 5. 7 115TP 1 1/ 8 1/4 x 1/8 x 4 1/ 8 1 5. 6 115SMTP 115TP 1 /16 1/4 x 1/8 x 4 1/ 8 1 5. 4 115TP4 1 1/ 4 1/4 x 1/8 x 4 1/ 8 1 5. 115TP5 1 5/16 5/16 x 5/ x 4 1/ 8 5. 1 0.855 /816 x 1 1/ 4 9 115TP6 1 / 8 5/16 x 5/ x 4 1/ 8 4. 8 115TP7 1 7/16 /8 x /16 x 4 1/ 8 4. 7 115TP8 1 1/ /8 x /16 x 4 1/ 8 4. 4 115TP1 1 5/ 8 /8 x /16 x 4 1/ 8 4. 0 115TP111 1 11/16 /8 x /16 x 4 1/ 8. 7 115TP11 1 / 4 /8 x /16 x 4 1/ 8. 5 115TP115 1 15/16 1/ x 1/4 x 4 1/ 8. 7 Note: When using shafts smaller than the largest bushing bore shown for a specific reducer, shaft stress based on the transmitted load must always be checked. 64

Accessories SMTP, MTP, CMTP TorqTaper Plus ushing Kits Unit s 015 REDUCER SIZE USING NO. ORE SIZE SAFT KEYSEAT REQUIRED TYPE 0TP 1 /16 1/4 x 1/8 x 4 5/ 8 1 STAILIZER RING WIDT OLT TORQUE OLT SIZE FT.LS. WEIGT 0TP4 1 1/ 4 1/4 x 1/8 x 4 5/ 8 1 7. 0TP5 1 5/16 5/16 x 5/ x 4 5/ 8 1 7. 1 0TP6 1 / 8 5/16 x 5/ x 4 5/ 8 1 6. 9 7.5 Shaft Mount Accessories 0SMTP 0TP7 1 7/16 /8 x /16 x 4 5/ 8 1 6. 6 0TP8 1 1/ /8 x /16 x 4 5/ 8 6. 1 0TP1 1 5/ 8 /8 x /16 x 4 5/ 8 0.980 /816 x 1 1/ 4 9 5. 9 0TP111 1 11/16 /8 x /16 x 4 5/ 8 5. 6 0TP11 1 / 4 /8 x /16 x 4 5/ 8 5. 4 0TP114 1 7/ 8 1/ x 1/4 x 4 5/ 8 4. 8 0TP115 1 15/16 1/ x 1/4 x 4 5/ 8 4. 4 0TP00 1/ x 1/4 x 4 5/ 8 4. 0TP0 /16 1/ x 1/4 x 4 5/ 8. 1 07TP6 1 / 8 5/16 x 5/ x 5 1/ 8 1 9.6 07TP7 1 7/16 /8 x /16 x 5 1/ 8 1 9. 07TP8 1 1/ /8 x /16 x 5 1/ 8 1 9. 1 07TP1 1 5/ 8 /8 x /16 x 5 1/ 8 8. 5 07SMTP 07TP111 1 11/16 /8 x /16 x 5 1/ 8 8. 07TP11 1 / 4 /8 x /16 x 5 1/ 8 7. 9 07TP114 1 7/ 8 1/ x 1/4 x 5 1/ 8 1.040 /816 x 1 1/ 4 9 7. 07TP115 1 15/16 1/ x 1/4 x 5 1/ 8 6. 9 07TP00 1/ x 1/4 x 5 1/ 8 6. 6 07TP0 1/ 8 1/ x 1/4 x 5 1/ 8 5. 9 07TP0 /16 1/ x 1/4 x 5 1/ 8 5. 5 07TP04 1/ 4 1/ x 1/4 x 5 1/ 8 5. 1 07TP07 7/16 5/8 x 5/16 x 5 1/ 8. 9 15TP7 1 7/16 /8 x /16 x 5 5/ 8 1 14.9 15TP8 1 1/ /8 x /16 x 5 5/ 8 1 14. 5 15TP111 1 11/16 /8 x /16 x 5 5/ 8 1 1. 6 15TP11 1 / 4 /8 x /16 x 5 5/ 8 1 1. 15SMTP 15TP114 1 7/ 8 1/ x 1/4 x 5 5/ 8 1. 6 15TP115 1 15/16 1/ x 1/4 x 5 5/ 8 1. 15TP00 1/ x 1/4 x 5 5/ 8 1.140 /816 x 1 / 8 9 11. 9 15TP0 /16 1/ x 1/4 x 5 5/ 8. 7 15TP04 1/ 4 1/ x 1/4 x 5 5/ 8 9.80 15TP07 7/16 5/8 x 5/16 x 5 5/ 8 8.90 15TP08 1/ 5/8 x 5/16 x 5 5/ 8 8.50 15TP11 11/16 5/8 x 5/16 x 5 5/ 8 7.00 15TP15 15/16 /4 x /8 x 5 5/ 8 5.00 Note: When using shafts smaller than the largest bushing bore shown for a specific reducer, shaft stress based on the transmitted load must always be checked. 65

Accessories SMTP, MTP, CMTP TorqTaper Plus ushing Kits Unit s 0715 Width Stabilizer Ring External Key Furnished Key Furnished Type 1 Type REDUCER SIZE 07SMTP USING NO. ORE SIZE SAFT KEYSEAT REQUIRED TYPE 07TP115 1 15/16 1/ x 1/4 x 6 / 4 1 STAILIZER RING WIDT OLT TORQUE OLT SIZE FT.LS. WEIGT 07TP00 1/ x 1/4 x 6 / 4 1 1.1 07TP0 /16 1/ x 1/4 x 6 / 4 1 19.76 07TP04 1/ 4 1/ x 1/4 x 6 / 4 1 19.7 07TP06 / 8 5/8 x 5/16 x 6 / 4 18.8 07TP07 7/16 5/8 x 5/16 x 6 / 4 17.68 07TP08 1/ 5/8 x 5/16 x 6 / 4 1.45 1/1 x 1 5/ 8 65 17.08 07TP11 11/16 5/8 x 5/16 x 6 / 4 15.6 1.61 07TP14 7/ 8 /4 x /8 x 6 / 4 1.51 07TP15 15/16 /4 x /8 x 6 / 4 1.89 07TP00 /4 x /8 x 6 / 4 1.76 07TP06 / 8 7/8 x 7/16 x 6 / 4 7.55 07TP07 7/16 7/8 x 7/16 x 6 / 4 7.11 REDUCER SIZE 15SMTP USING NO. ORE SIZE SAFT KEYSEAT REQUIRED TYPE 15TP07 7/16 5/8 x 5/16 x 7 15/16 1 STAILIZER RING WIDT OLT TORQUE OLT SIZE FT.LS. WEIGT 15TP08 1/ 5/8 x 5/16 x 7 15/16 1 0.47 15TP11 11/16 5/8 x 5/16 x 7 15/16 1 8.09 15TP1 1/16 /4 x /8 x 7 15/16 1 6.8 15TP14 7/ 8 /4 x /8 x 7 15/16 1 6.09 1.69 1/1 x 1 / 4 65 15TP15 15/16 /4 x /8 x 7 15/16.95 15TP00 /4 x /8 x 7 15/16.90 15TP0 /16 /4 x /8 x 7 15/16 0.65 0.89 15TP07 7/16 7/8 x 7/16 x 7 15/16 17. 15TP15 15/16 1 x 1/ x 7 15/16 11.4 Note: When using shafts smaller than the largest bushing bore shown for a specific reducer, shaft stress based on the transmitted load must always be checked. 66

Accessories SMTP TorqTaper Plus ushing Kits Unit s 407800 Width Shaft Mount Accessories Stabilizer Ring External Key Furnished Key Furnished Type 1 Type Reducer 407SMTP Reducer 415SMTP Reducer 507SMTP Reducer 608SMTP ushing No. ore Shaft Keyseat Required Type Stabilizer Ring Width olt olt Ft. Lbs. 407TP15 15/16 /4 x /8 x 7 1/ 1 0. 407TP0 /16 /4 x /8 x 7 1/ 9. 407TP07 7/16 7/8 x 7/16 x 7 1/ 6. 5 1.56 1/1 x 1 / 4 65 407TP15 15/16 1 x 1/ x 7 1/ 0. 1 407TP40 4 /16 1 x 1/ x 7 1/ 16. 5 407TP407 4 7/16 1 x 1/ x 7 1/ 1. 6 Weight ushing ore Shaft Keyseat Stabilizer Ring olt Type No. Required Width olt Ft. Lbs. Weight 415TP07 7/16 7/8 x 7/16 x 9 1/ 4 5.1 415TP15 15/16 1 x 1/ x 9 1/ 4 44. 4 415TP40 4 /16 1 x 1/ x 9 1/ 4 40. 1 1.59 5/811 x 140 415TP407 4 7/16 1 x 1/ x 9 1/ 4 5. 5 415TP408 4 1/ 1 x 1/ x 9 1/ 4 4. 415TP415 4 15/16 1 1/4 x 5/8 x 9 1/ 4 5. 6 ushing ore Shaft Keyseat Stabilizer Ring olt Type No. Required Width olt Ft. Lbs. Weight 507TP15 15/16 1 x 1/ x / 8 65.0 507TP40 4 /16 1 x 1/ x / 8 59. 0 507TP407 4 7/16 1 x 1/ x / 8 1.56 /4 x 1/ 4 50 54. 0 507TP415 4 15/16 1 1/4 x 5/8 x / 8 45. 0 507TP507 5 7/16 1 1/4 x 5/8 x / 8 7. 0 ushing ore Shaft Keyseat Stabilizer Ring olt Type No. Required Width olt Ft. Lbs. Weight 608TP507 5 7/16 1 1/4 x 5/8 x 11 80.0 608TP515 5 15/16 1 1/ x /4 x 11 7. 0 608TP600 6 1 1/ x /4 x 11 1.71 /4 x / 4 50 70. 0 608TP607 6 7/16 1 1/ x /4 x 11 64. 0 608TP608 6 1/ 1 1/ x /4 x 11 6. 0 R educer ushing No. ore Shaft Keyseat Stabilizer Ring olt Type Required Width olt Ft.Lbs. Weight 800TP515 5 15/16 1 1/ x /4 x 11 168.0 800TP600 6 1 1/ x /4 x 11 165. 0 800SMTP 800TP608 6 1/ 1 1/ x /4 x 11 1.88 7/89 x / 4 400 147. 0 800TP700 7 1 /4 x 7/8 x 11 18. 0 800TP800 8 x 1 x 11 84. 0 Notes: When using shafts smaller than the largest bushing bore shown for a specific reducer, shaft stress based on the transmitted load must always be checked. 67

Accessories SMFP Finished ore ushings Unit s 707 rowning shaft mount reducers may be mounted on shafts smaller than the output bore of the reducer by using the wide selection of bushings offered. These stock bushing kits contain one keyed bushing, one plain bushing, keys and setscrews necessary to fit the smaller shaft. Figure 1 Thick wall bushing internal key Figure Thin wall bushing offset key Figure Thin wall bushing rectangular or square key Figure 4 No bushing Reducer 7SMFP 115SMFP 0SMFP 07SMFP Shaft Shaft ushing Wt. Fig. Dia. Keyseat Kit No Lbs. /4" /16 x / x " 7U01 1 1. 4 7/8 /16 x / x 7U014 1 1. 15/16 1/4 x 1/8 x 7U015 1. 1 1 1/4 x 1/8 x 7U0 1. 0 1 1/16 1/4 x 1/8 x 7U1. 9 1 1/8 1/4 x 1/8 x 7U. 8 1 /16 1/4 x 1/8 x 7U. 6 1 1/4 1/4 x 1/8 x 7U4. 5 1 5/16 5/16 x 5/ x 7U5. 4 1 7/16 /8 x /16 x NONE 4 15/16 1/4 x 1/8 x 1/ 115U015 1. 1 1/4 x 1/8 x 1/ 115U0 1. 1 1 1/16 1/4 x 1/8 x 1/ 115U1 1. 0 1 1/8 1/4 x 1/8 x 1/ 115U 1. 8 1 /16 1/4 x 1/8 x 1/ 115U 1. 7 1 1/4 1/4 x 1/8 x 1/ 115U4 1. 5 1 5/16 5/16 x 5/ x 1/ 115U5. 1 /8 5/16 x 5/ x 1/ 115U6. 1 1 7/16 /8 x /16 x 1/ 115U7 1. 9 1 1/ /8 x /16 x 1/ 115U8 1. 7 1 5/8 /8 x /16 x 1/ 115U1 1. 1 11/16 /8 x /16 x 1/ 115U111 1. 1 1 /4 /8 x /16 x 1/ 115U11. 8 1 15/16 1/ x 1/4 x 1/ NONE 4 1 /16 1/4 x 1/8 x 1/ 0U 1. 8 1 1/4 1/4 x 1/8 x 1/ 0U4 1. 6 1 5/16 5/16 x 5/ x 1/ 0U5 1. 5 1 /8 5/16 x 5/ x 1/ 0U6 1. 4 1 7/16 /8 x /16 x 1/ 0U7 1. 1 1 1/ /8 x /16 x 1/ 0U8. 9 1 5/8 /8 x /16 x 1/ 0U1. 4 1 11/16 /8 x /16 x 1/ 0U111. 1 /4 /8 x /16 x 1/ 0U11. 0 1 7/8 1/ x 1/4 x 1/ 0U114 1. 5 1 15/16 1/ x 1/4 x 1/ 0U115 1. 1/ x 1/4 x 1/ 0U00. 9 /16 1/ x 1/4 x 1/ NONE 4 1 /8 5/16 x 5/ x 1/ 07U6 1 6. 4 1 7/16 /8 x /16 x 1/ 07U7 1 6. 1 1 1/ /8 x /16 x 1/ 07U8 1 5. 8 1 5/8 /8 x /16 x 1/ 07U1 5. 1 11/16 /8 x /16 x 1/ 07U111 4. 9 1 /4 /8 x /16 x 1/ 07U11 4. 5 1 7/8 1/ x 1/4 x 1/ 07U114. 8 1 15/16 1/ x 1/4 x 1/ 07U115. 5 1/ x 1/4 x 1/ 07U00. 1 1/8 1/ x 1/4 x 1/ 07U0. /16 1/ x 1/4 x 1/ 07U0 1. 8 1/4 1/ x 1/4 x 1/ 07U04 1. 4 7/16 5/8 x 5/16 x 1/ NONE 4 Note: When using bushings to adapt a SMFP shaft mount reducer to a smaller shaft, the shaft stress based on the transmitted load must always be checked. 68

Accessories SMFP Finished ore ushings Unit s 1515 rowning shaft mount reducers may be mounted on shafts smaller than the output bore of the reducer by using the wide selection of bushings offered. These stock bushing kits contain one keyed bushing, one plain bushing, keys and setscrews necessary to fit the smaller shaft. Figure 1 Thick wall bushing internal key Figure Thin wall bushing offset key Shaft Mount Accessories Figure Thin wall bushing rectangular or square key Figure 4 No bushing Reducer 15SMFP 07SMFP 15SMFP Shaft Shaft ushing Wt. Fig. Dia. Keyseat Kit No. Lbs. 1 7/16 /8 x /16 x 4 15U7 1 11. 7 1 1/ /8 x /16 x 4 15U8 1 11. 4 1 11/16 /8 x /16 x 4 15U111 1. 1 /4 /8 x /16 x 4 15U11 1 9. 9 1 7/8 1/ x 1/4 x 4 15U114 1 9. 1 1 15/16 1/ x 1/4 x 4 15U115 8. 7 1/ x 1/4 x 4 15U00 8. /16 1/ x 1/4 x 4 15U0 6. 9 1/4 1/ x 1/4 x 4 15U04 6. 4 7/16 5/8 x 5/16 x 4 15U07 4. 8 1/ 5/8 x 5/16 x 4 15U08 4. 11/16 5/8 x 5/16 x 4 15U11. 5 15/16 /4 x /8 x 4 None 4 1 15/16 1/ x 1/4 x 4 1/ 07U115 1 16. 1/ x 1/4 x 4 1/ 07U00 1 15. 7 /16 1/ x 1/4 x 4 1/ 07U0 1 14. 1 1/4 1/ x 1/4 x 4 1/ 07U04 1 1. 6 7/16 5/8 x 5/16 x 4 1/ 07U07 11. 8 1/ 5/8 x 5/16 x 4 1/ 07U08 11. 11/16 5/8 x 5/16 x 4 1/ 07U11 9. 7/8 /4 x /8 x 4 1/ 07U14 7. 1 15/16 /4 x /8 x 4 1/ 07U15 6. 4 7/16 7/8 x 7/16 x 4 1/ None 4 7/16 5/8 x 5/16 x 4 1/ 15U07 1 19. 1/ 5/8 x 5/16 x 4 1/ 15U08 1 18. 6 11/16 5/8 x 5/16 x 4 1/ 15U11 16. 6 1/16 /4 x /8 x 4 1/ 15U1 15. 7/8 /4 x /8 x 4 1/ 15U14 14. 5 15/16 /4 x /8 x 4 1/ 15U15 1. 8 /4 x /8 x 4 1/ 15U00 1. 1 /16 /4 x /8 x 4 1/ 15U0. 7 7/16 7/8 x 7/16 x 4 1/ 15U07 7. 4 15/16 1 x 1/ x 4 1/ None 4 Note: SMFP units and bushings are madetoorder. Contact Emerson for delivery. Note: When using bushings to adapt a SMFP shaft mount reducer to a smaller shaft, the shaft stress based on the transmitted load must always be checked. 69

Accessories Shaft Mount Reducers Top Mount Motor Mounts W Motor Mount L D E V U D G M. M. CENTER DISTANCE Adapter 9.00 S G MIN. MIN. CENTER DISTANCE MIN. M. U1 C/ C N R Supports Motor ase Dimensions in Inches Motor U Frame D E V Dia. Keyseat 56.50.75 0.6 /16 x / 1.88 14T, 145T.50.5 0.88 /16 x /.5 18T, 184T 4.50.75 1.1 1/4 x 1/8.75 1T, 15T 5.5.50 1.8 5/16 x 5/.8 54T, 56T 6.5 4.5 1.6 /8 x /16 4.00 84T, 86T 7.00 4.75 1.88 1/ x 1/4 5.6 4T, 6T 8.00 5.5.1 1/ x 1/4 5.5 64T, 65T 9.00 5.88.8 5/8 x 5/16 5.88 404T, 405T 11.00 6.6.88 /4 x /8 7.5 444T, 447T 11.00 7.50.8 7/8 X 7/16 8.50 * To determine usable input shaft length, see pages 46. Part Number Explanation Motor Mount components may be ordered individually or as a kit. To order the complete kit use the following format: Reducer Top or Side Mount igh or Low mount 70 07 TOP IG MM KIT

Accessories Shaft Mount Reducers Top Mount Motor Mounts DIMENSIONS asic Motor Motor Reducer Mount Mount Motor Motor Support Adapter ase Mount Assy. G Shaft Wt. Lbs. C L N* R S W U1 Min. Max. Min. Max. Dia. Keyseat 7 IG MMS7 51.0 8.78 18.15.75 1.64 7.61 15.50 4.08 1.18 0.6 16.50 0.75 /16 x / 7 LOW MMS7L 48.0 5.75 9.50 MMA7115 M7115 115 IG MMS115 51.0 6.94 17.74 4. 1.64 7.61 15.50 4.4 1.5 0.6 16.50 1.1 1/4x1/8 115 LOW MMS115L 48.0 7.77 9.9 0 IG MMS0 11.8 7.00 16.91 MMA0 4.96 1.89 7.6 0.5 5.1 1.48 0.75 0.00 1.5 1/4 x 1/8 0 LOW MMS0L 7.8 7.94.41 M007 07 IG MMS07 118.6 8.06 19.94 MMA07 5.94 1.89 7.6 0.5 5.1 1.6 0.75 0.00 1.44 /8x/16 07 LOW MMS07L 11.6.44.44 15 IG MMS15 14.4 11.4 1.75 MMA15 M1507 6.88 1.89 7.6 15 LOW MMS15L 16.4.50.50 0.5 5.87.1 0.75 4.00 1.87 1/ x 1/4 07 IG MMS07 150.0 6.18 MMA07 M1507 7.95 1.89 7.6.8 07 LOW MMS07L 141.0 14.5 0.00 7.45.5 0.75 4.00.00 1/ x 1/4 15 IG MMS15 177.0 7.09 MMA15 M15 8.9 1.89 7.6.50 15 LOW MMS15L 168.0 14.65.50 8..6 0.75 4.00.1 1/x1/4 407 IG MMS407 MMA407415 M407415 6.0 9.5.09 1.98 14.59 19.1 7.00 6.70.1 1.50.50.1 1/ x 1/4 415 IG MMS415.0.8.09 1.98 1.4 18.5 7.00 9..6 1.50.50.7 5/8 x 5/16 507 IG MMS507 MMA507608 M507608 9.0 11.78.09 1.98 15.08 0.97 0.00 9.7 4.19 1.50 7.00.6 5/8 x 5/16 608 IG MMS608 40.0 9.06.09 1.98 16.6 0.79 0.00 9.51 4.5 1.50 7.00.69 5/8 x 5/16 800 IG MMS800 MMA800 M800 604.0.7 1.87 7.6 7.6 1.00 1.75 4.88 1.50 9.50.94 /4 x /8 Shaft Mount Accessories asic Reducer Motor Mount Support Motor Mount Adapter Motor ase Minimum and Maximum Center Distances (in inches) for Motor Frame s 56 14T, 145T 18T, 184T 1T, 15T 54T,56T 84T, 86T 4T, 6T 641, 65T 404T, 405T 444T, 447T Min. Max. Min. Max. Min. Max. Min. Max. Min. Max. Min. Max. Min. Max. Min. Max. Min. Max. Min. Max. 7 IG MMS7 17.7.05 17.7.05 18.7 4.05 19.47 4.80 7 LOW MMS7L 14.71 4.41 14.71 4.41 15.71 5.41 16.45 6.16 MMA7115 M7 115 115 IG MMS115 16.50.4 16.50.4 17.50 4.4 18.5 4.99 115 LOW MMS115L 17. 5.4 17. 5.4 18. 6.4 19.06 7.18 0 IG MMS0 17.70.06 17.70.06 18.70 4.06 19.44 4.81 0.44 5.81 1.19 6.56 MMA0 0 LOW MMS0L 18.64 6.57 18.64 6.57 19.6 7.57 0.8 8. 1.8 9.1.1 0.06 M0 07 07 IG MMS07 19.59 6.91 19.59 6.91 0.59 7.91 1.4 8.66.4 9.66.08 40.41 MMA07 07 LOW MMS07L 1.97 7.4 1.97 7.4.96 8.4.71 9.17 4.71 0.17 5.46 0.9 15 IG MMS15.9 9.67 4.9 40.67 5.67 41.4 6.66 4.4 7.41 4.17 8.41 44.17 9.41 45.17 MMA15 M1507 15 LOW MMS15L.00 8.45.99 9.44 4.74 0.19 5.74 1.19 6.48 1.94 7.48.94 8.48.94 07 IG MMS07 MMA07 M1507 4.56 45.88 5.0 46.6 6.0 47.6 7.05 48.8 8.05 49.8 9.05 50.8 07 LOW MMS07L.97 4.7 5.7 6.47 7.47 8.47 15 IG MMS15 MMA15 M15 5.57 47.55 6.1 48.0 7.1 49.0 8.05 50.05 9.05 51.05 0.05 5.05 15 LOW MMS15L 5.14 5.89 6.89 7.64 8.64 9.64 407 IG MMS407 MMA407415 M407415.56 47.04.55 48.0 4.0 48.78 5.9 49.78 6.9 50.78 7.9 51.78 8.8 5.77 415 IG MMS415.7 47.9.6 48.9 4.00 49.04 5.00 50.0 51.0 7.00 5.0 8.00 5.0 507 IG MMS507 MMA507608 M507608 6.4 5.15 7.18 5.90 8.17 5.90 9.17 54.89 40.16 55.89 41.16 56.89 608 IG MMS608 9.4 5.80 40.17 54.54 41.17 55.54 4.16 56.54 4.16 57.5 44.15 58.5 800 IG MMS800 MMA800 M800 54.00 6.55 54.98 64.55 55.98 65.55 56.97 66.54 Screw Conveyor Trough Clearance Table When a motor mount is used on screw conveyor drives, the amount shown in the table below must be added to the minimum center distance shown above. Maximum center distance is unchanged. asic Reducer 7 IG 7 LOW 115 IG 115 LOW 0 IG 0 LOW 07 IG 07 LOW 15 IG 15 LOW 07 IG 07 LOW 15 IG 15 LOW 407 IG Conveyor Diameter 6 9 1 14 16 18 0 4 0 0 1.88.75.75.75 5.6 7.50 1.88.75 0.16.16 4. 4. 6.68 8.64 8.64 0.16.16.16 0.48.48 4.96 4.96 7.44 9.9 9.9 0.48.48.48.97.97.97 5.94 5.94 8.91 8.91 0 0 0 0 0 0.44.44.44 6.88. 0 0 0 0.98.98.98 7.95 11.9 0.98.98.98 N/ A N/ A / A 0 0 4.15 4.15.6 4.15 4.15.6 4.15 4.15.6 8.0.6 N 0 4 9 4 9 4 9 4 9 * 1.45 * Refer to Application Engineering (1 800 66 09). 71

Accessories Shaft Mount Reducers Side Mount Motor Mounts Motor Mount W L D Adapter E U D G M. M. CENTER DISTANCE V 9.00 S U1 G MIN. MIN. CENTER DISTANCE MIN. M. N C/ C R Supports Motor ase Motor Frame * To determine usable input shaft length, see pages 46. D E Dimensions in Inches Dia. U Keyseat 56.50.75 0.6 /16 x / 1.88 14T, 145T.50.5 0.88 /16 x /.5 18T, 184T 4.50.75 1.1 1/4 x 1/ 8.75 1T, 15T 5.5.50 1.8 5/16 x 5/.8 54T, 56T 6.5 4.5 1.6 /8 x /16 4.00 84T, 86T 7.00 4.75 1.88 1/ x 1/ 4 5.6 4T, 6T 8.00 5.5.1 1/ x 1/ 4 5.5 64T, 65T 9.00 5.88.8 5/8 x 5/16 5.88 V Part Number Explanation Motor Mount components may be ordered individually or as a kit. To order the complete kit use the following format: Reducer Top or Side Mount igh or Low mount 7 07 SIDE LOW MM KIT

Accessories Shaft Mount Reducers Side Mount Motor Mounts asic Reducer 7 IG 7 LOW 115 IG 115 LOW 0 IG 0 LOW 07 IG 07 LOW 15 IG 15 LOW 07 IG 07 LOW 15 IG 15 LOW Motor Mount Support MMS7 MMS7L MMS115 MMS115L MMS0 MMS0L MMS07 MMS07L MMS15 MMS15L MMS07 MMS07L MMS15 MMS15L Motor Mount Adapter MMA7115 MMA0 Motor ase M7115 MMA07 M007 MMA15 M1507 MMA07 M1507 MMA15 M15 MMA15S M15 Motor Mount Assy. Wt. Lbs. 51.0 48.0 51.0 48.0 11.8 7.8 118.6 11.6 14.4 16.4 150.0 141.0 177.0 168.0 Dimensions Shaft G C L N* R S W U1 M in. M ax. M in. M ax. Dia. Keyseat 1.88 1.64 7.61 8.78 18.15 5.75 9.50 15.50 4.08.56 0.6 16.50 0.75 /16 x /.16 1.64 7.61 6.94 17.74 7.77 9.9 15.50 4.4.74 0.6 16.50 1.1 1/4 x 1/ 8.48 1.89 7.6 7.00 16.91 7.94.41 0.5 5.1.54 0.75 0.00 1.5 1/4 x 1/ 8.97 1.89 7.6 8.06 19.94.44.44 0.5 5.1 4.00 0.75 0.00 1.44 /8 x /16.44 1.89 7.6 11.4 1.75.50.50 0.5 5.87 4.59 0.75 4.00 1.87 1/ x 1/ 4.97 1.89 7.6.8 0.15 18..00 7.45 5.01 0.75 4.00.00 1/ x 1/ 4 4.16 1.89 7.6.50 1. 18.80.50 8. 5.6 0.75 4.00.1 1/ x 1/ 4 Shaft Mount Accessories asic Reducer 7 IG 7 LOW 115 IG 115 LOW 0 IG 0 LOW 07 IG 07 LOW 15 IG 15 LOW 07 IG 07 LOW 15 IG 15 LOW Motor Motor Minimum and Maximum Center Distances (in inches )for Motor Frame s Motor Mount Mount 56 14T, 145T 18T, 184T 1T, 15T 54T, 56T 84T, 86T 4T, 6T 64T, 65T ase Support Adapter M in. M ax. M in. M ax. M in. M ax. M in. M ax. M in. M ax. M in. M ax. M ax. M in. M ax. Min. MMS7 1.91 1.00 1.91 1.00 14.89.00 15.6.74 MMA7115 MMS7L.95.9.95.9 11.9.8 1.66 4.1 M7115 MMS115 1.5 1.00 1.5 1.00 1..00 1.96.74 MMA0 MMS115L.96..96. 11.9 4. 1.66 4.96 MMS0 1.66 0. 1.66 0. 1.6 1. 14.4 1.97 15.1.96 16.05.71 MMA07 M007 MMS0L 1.56.76 1.56.78 14.5 4.77 15.6 5.5 16. 6.51 16.96 7.5 MMS07 1.89.86 1.89.86 14.85 4.85 15.57 5.60 16.54 6.59 17.7 7.4 MMA15 M1507 MMS07L 1. 4.45 1. 4.45 14.8 5.44 15.00 6.18 15.97 7.17 16.70 7.91 MMS15 1.76 5.94 14.71 6.9 15.4 7.68 16.8 8.67 17. 9.41 18.07 40.41 19.04 41.41 MMA07 M1507 MMS15L 1.89 4.8 1.8 5.81 14.54 5.54 15.49 7.5 16.1 8.7 15.55 7.59 16.51 8.58 MMS07 4.05 4.79 4.79 44.5 0.5 45.5 1.50 46.5 MMA15 M15 17.15 17.87 18.8 19.56 MMS07L 0.4 0.98 1.97.71 0.5.70 1.50 4.69 MMS15 4.86 4.60 44.60 45.4 0.5 46. 1.49 47. MMA15S M15 17.16 17.88 18.84 19.56 MMS15L 0.56 1.9.8.0 0.5 4.01 1.49 5.00 Screw Conveyor Trough Clearance Table When a motor mount is used on screw conveyor drives, the amount shown in the table below must be added to the minimum center distance shown on page 71. Maximum center distance is unchanged. asic Reducer 7 IG 7 LOW 115 IG 115 LOW 0 IG 0 LOW 07 IG 07 LOW 15 IG 15 LOW 07 IG 07 LOW 15 IG 15 LOW Conveyor Diameter 6 9 1 14 16 18 0 4 0 0 0 0 0 0 0 1.88.16.16.48 0 0 0 0 0 0 1.88.16.16.48 0 0 0 0.44 0.75 16 4..48.48.97.97.44.44 0 0 0 0 1.88 5.6 4. 4.96.48.97.97.44.44 0 0 0 0.75 6.48 6.48 4.96 4.96 5.94 5.94 6.88 6.88.98.98 4.15 4.15 5.6 6.48 7.44 5.94 5.94 6.88 6.88.98.98 4.15 4.15 7.50 8.64 9.9 8.91 6.88.98.98 4.15 4.15 11.88. 7.95 7.95 8.0 8.0 * Refer to Application Engineering (1 800 66 09). 7

rowning elt Drives For over years rowning has been an innovator of quality belt drive solutions for varying equipment and demanding applications. Today, rowning offers the most extensive belt drive product line in the world. Our extensive offering has many patented and exclusive design features not found in any other sheave. Shaft Mount Accessories Key Product Offerings: Complete Line of F sheaves Complete Line of Multiple Sheaves in both QD and Split Taper designs rowning Split Taper ushings etter concentricity for easy assembly Keytokey drive /4" ft. selflocking taper Available in inch and metric bores rowning Patented 5V Sheaves (Not for use with anded elts) Interchanges with popular QD and Split Taper sheave designs Patented design provides the power of 5V belts in the economy of a section sheave. Serves 90% of all applications from 15 Increases by 40% (or reduces cost by 40%) rowning rand Vbelts Unique design enhances performance, provides increased horsepower capacity in short center drives Single fabric design reduces vibration (wrapped belt) Ground form edges reduce center distance variation and drive vibration (raw edge) rowning belts and sheaves provide 4X the product offering of any competitor rowning VP Vortex Variable Sheaves Increased wall thickness and hub design for increased horsepower capacity and shorter center drives Tighter tolerances for reduced vibration External rib design provides extra cooling for longer belt life rowning MVP Variable Sheaves Economical and infinite mechanical speed adjustment Offered up to grooves Serves applications up to 750 hp An excellent solution for dual drive applications 75

Accessories Shaft Mount Reducers Preselected elt Drives 7SMTP05 7SMTP05 Variable 7SMTP05 elt elts Variable ushing ushing ushing ushing elts 90 96 VP50 X 90 9 AK9 5V160 97 8 VP56 94 97 AK41 AK144 9 14 AK14 98 4 K6 VP50 15 140 5V1 5 1 T40 5V14 P1 141 160 VP4 5V80 111 115 5V4 161 181 VP60 X 116 11 K K1 18 196 VP65 1 19 K4 X 197 06 VP60 16 K6 K0 07 0 17 14 K40 VP65 1 7 144 147 T40 5V90 P1 8 5 148 151 K6 6 46 VP71 X 15 160 K40 47 5 161 164 T8 P1 5 7 VP65 165 17 K45 K80 X 74 85 VP71 17 180 K47 K90 X 86 96 VP6 5V5 181 184 5V4 P1 97 0 VP65 X 185 19 K50 04 07 VP6 19 00 K5 08 09 5V6 01 1 K55 VP65 4 14 6 AK54 5 50 VP71 7 4 AK56 AK84 51 5 VP60 X 5 44 AK84 54 8 VP65 5V5 45 50 K57 84 400 VP71 51 6 K60 64 7 K6 74 80 K65 K80 81 8 5V50 84 00 K57 01 17 K60 18 8 K6 K67 X 9 7 K57 8 56 K60 57 69 K6 K60 70 87 K65 88 400 K67 elt Notes: Preselected belt drives are based on the following guidelines: NEMA Recommendations for Sheave Diameter and Width Average Service at Reducer Rated Load elt Minimum For other conditions (including but not limited to; fire hazard, explosion hazard or choked input), contact Application Engineering (1 800 66 09) for assistance in selecting a belt drive. It is recommended that 50 hp motors and larger the sheave diameters shown be checked with the motor manufacturer to be sure they meet their recommendations for minimum pitch diameter. 76

Accessories Shaft Mount Reducers Preselected elt Drives 7SMTP09 7SMTP09 Variable 7SMTP09 elt Variable elts elts ushing ushing ushing ushing 16 0 VP6 1 AK T00 1 VP4 1 AK5 T80 4 0 VP6 X 14 AK6 1 15 K VP4 7 5V00 X 16 K4 8 44 VP50 17 K6 45 49 18 K40 VP56 50 54 19 0 K45 55 56 VP60 AK184 1 K47 57 58 VP65 AK 59 61 AK VP50 6 65 5V16 4 K8 5V00 66 7 VP56 5 AK5 74 81 VP4 5V90 6 AK6 8 8 VP56 X 7 AK7 K 84 95 VP60 8 9 AK8 96 0 1 AK0 VP65 TA195 4 6 X AK 7 11 5V1 4 AK4 VP71 114 117 5 6 K 118 1 VP75 7 8 K4 X 14 15 VP60 9 40 K6 16 15 41 4 K40 K190 X VP65 5V86 16 18 4 44 T8 P1 19 148 VP71 45 K45 149 156 VP60 46 K47 X 157 170 VP65 5V68 47 49 K0 5V1 171 186 VP71 50 5 K 187 00 VP65 5V58 54 56 AK41 57 60 AK44 61 6 AK46 AK144 64 67 AK49 68 69 AK51 70 7 AK9 AK4 74 79 AK41 80 8 AK9 AK94 84 88 AK54 89 91 AK56 AK14 9 96 AK59 97 99 AK51 0 5 AK54 6 9 AK56 AK4 1 114 AK59 115 K55 11 15 K57 16 1 K60 5V86 X 1 15 K6 16 144 AK74 AK4 145 146 5V50 147 155 K57 5V68 156 164 K60 165 170 5V50 171 178 K57 X K65 179 188 K60 189 194 K6 195 198 5V66 199 00 5V68 5V68 elt T80 Shaft Mount Accessories Notes: Preselected belt drives are based on the following guidelines: NEMA Recommendations for Sheave Diameter and Width Average Service at Reducer Rated Load elt Minimum For other conditions (including but not limited to; fire hazard, explosion hazard or choked input), contact Application Engineering (1 800 66 09) for assistance in selecting a belt drive. It is recommended that 50 hp motors and larger the sheave diameters shown be checked with the motor manufacturer to be sure they meet their recommendations for minimum pitch diameter. 77

Accessories Shaft Mount Reducers Preselected elt Drives 7SMTP15 7SMTP15 Variable 7SMTP15 elt Variable elts ushing ushing ushing 1 VP6 7 AK 14 16 VP4 5V78 8 AK5 17 VP50 9 AK1 18 AK154 AK 5V78 VP6 4 9 11 AK5 AK14 0 1 1 K5 8 AK114 1 AK VP4 9 46 AK94 14 AK 47 5 AK84 15 AK5 5V00 5 59 VP50 16 AK7 5V90 60 65 VP56 17 AK K160 66 71 AK74 18 AK8 7 80 VP50 5V66 19 0 AK0 81 8 AK61 1 AK AK184 84 9 VP60 AK4 X 94 5V68 AK VP65 95 0 4 AK 1 5 5 6 K8 K VP60 5V60 6 11 7 8 AK6 114 16 VP65 9 AK7 K60 X 17 VP71 0 AK8 1 AK0 4 AK AK114 5 6 AK4 7 8 AK 9 40 AK4 41 4 AK0 44 46 AK 47 49 AK4 50 AK44 51 5 AK46 5 56 AK49 AK4 57 58 AK51 59 6 AK44 6 65 AK46 66 69 AK49 AK84 70 7 AK51 7 77 AK54 78 8 AK44 8 AK46 AK64 84 87 AK54 88 91 AK56 9 96 AK59 AK74 97 99 AK61 0 4 AK64 5 7 AK54 8 111 AK46 AK61 11 11 AK59 114 119 K57 16 K60 17 K6 ushing T80 AK4 TA8 elts 5V5 X elt Notes: Preselected belt drives are based on the following guidelines: NEMA Recommendations for Sheave Diameter and Width Average Service at Reducer Rated Load elt Minimum For other conditions (including but not limited to; fire hazard, explosion hazard or choked input), contact Application Engineering (1 800 66 09) for assistance in selecting a belt drive. It is recommended that 50 hp motors and larger the sheave diameters shown be checked with the motor manufacturer to be sure they meet their recommendations for minimum pitch diameter. 78

Accessories Shaft Mount Reducers Preselected elt Drives 7SMTP5 7SMTP5 Variable 7SMTP5 elt Variable elts ushing ushing ushing 6 7 5V78 5 AK0 8 5V00 6 AK 11 14 VP6 AK154 7 AK7 15 19 AK114 8 AK0 0 6 9 AK K190 AK84 7 1 AK5 8 5V88 11 AK8 VP4 9 47 AK56 1 AK0 AK184 48 5 AK49 1 AK4 54 57 VP50 14 K5 AK56 58 64 VP56 15 AK K1 65 70 X 16 AK VP50 71 77 5V4 P1 17 AK5 78 80 VP56 18 19 AK 0 K8 1 AK5 5V86 AK6 4 AK4 5 6 AK9 AK4 7 8 AK8 9 0 AK0 1 AK AK74 4 AK4 5 AK0 6 7 AK 8 40 AK4 AK64 41 4 44 45 AK9 46 48 AK41 49 51 AK44 AK61 5 54 AK46 55 58 AK49 59 6 AK44 6 65 AK46 66 69 AK49 70 7 AK51 AK51 7 77 AK54 78 80 AK56 ushing 5V78 elts elt Shaft Mount Accessories Notes: Preselected belt drives are based on the following guidelines: NEMA Recommendations for Sheave Diameter and Width Average Service at Reducer Rated Load elt Minimum For other conditions (including but not limited to; fire hazard, explosion hazard or choked input), contact Application Engineering (1 800 66 09) for assistance in selecting a belt drive. It is recommended that 50 hp motors and larger the sheave diameters shown be checked with the motor manufacturer to be sure they meet their recommendations for minimum pitch diameter. 79

Accessories Shaft Mount Reducers Preselected elt Drives 7SMTP5 7SMTP5 Variable 7SMTP5 elt Variable elts ushing ushing ushing 5 6 VP6 5 AK0 7 VP4 TA45 6 AK 5V00 8 VP50 7 AK7 9 11 VP6 8 AK0 AK14 1 1 VP4 9 AK 14 VP6 AK5 AK4 15 17 VP4 11 AK6 5V14 18 1 VP6 1 AK5 AK74 5 VP4 1 AK 6 1 VP6 14 AK 5V86 AK49 8 15 AK5 9 45 VP4 5V4 16 AK6 P1 46 50 T8 17 AK 18 AK 5V68 19 AK5 0 AK 1 AK AK5 5V56 4 AK6 5 AK 6 7 AK5 8 AK6 9 AK7 0 1 AK AK4 AK54 4 5 AK 6 7 AK4 AK49 8 9 AK9 40 41 AK41 4 44 AK44 AK51 45 46 AK46 47 48 AK49 49 50 AK AK ushing K55 elts elt Notes: Preselected belt drives are based on the following guidelines: NEMA Recommendations for Sheave Diameter and Width Average Service at Reducer Rated Load elt Minimum For other conditions (including but not limited to; fire hazard, explosion hazard or choked input), contact Application Engineering (1 800 66 09) for assistance in selecting a belt drive. It is recommended that 50 hp motors and larger the sheave diameters shown be checked with the motor manufacturer to be sure they meet their recommendations for minimum pitch diameter. 80

Accessories Shaft Mount Reducers Preselected elt Drives 115SMTP05 115SMTP05 Variable 115SMTP05 elt Variable elts elts ushing ushing ushing ushing 90 95 VP65 90 91 T6 P 96 5 VP71 5V4 X 9 96 T8 P1 X 6 1 VP75 97 98 K45 5V160 111 11 VP6 99 0 K47 114 1 VP65 1 4 K5 5V184 1 14 VP71 5 6 K55 15 140 VP75 7 1 K57 141 150 VP60 111 116 K60 K190 X 151 164 5V16 117 11 K6 VP65 X 165 179 1 14 K65 180 19 15 1 5V4 VP71 194 196 5V14 1 18 5V44 P1 5V14 197 08 VP75 19 14 K55 09 VP65 144 149 K57 11 9 VP71 Q5V9 150 5V5 5V16 X 0 4 VP75 151 157 K60 4 61 VP71 158 161 K6 5V94 6 76 VP75 16 168 5V54 77 80 VP65 169 174 5V56 81 06 VP71 5V80 175 181 5V58 07 VP75 18 187 5V60 5V14 11 0 VP71 188 19 5V6 1 7 VP75 5V74 194 0 5V64 8 49 V5870 0 08 5V66 X 50 67 V6880 5V80 09 14 5V68 68 86 MVP8094Q 5V86 X 15 4 5V50 87 400 V5870 15V64 5 5V5 4 4 5V54 5V86 4 44 5V56 45 57 5V60 58 65 5V6 66 74 5V64 5V90 75 8 5V66 8 90 5V68 91 97 5V80 K1 X 98 1 5V60 1 5V6 5V74 0 5V64 1 5V90 4 47 5V94 K1 X 48 6 5V70 5V74 64 8 5V74 84 94 V5V70 5V68 X 95 400 5V74 elt Shaft Mount Accessories Notes: Preselected belt drives are based on the following guidelines: NEMA Recommendations for Sheave Diameter and Width Average Service at Reducer Rated Load elt Minimum For other conditions (including but not limited to; fire hazard, explosion hazard or choked input), contact Application Engineering (1 800 66 09) for assistance in selecting a belt drive. It is recommended that 50 hp motors and larger the sheave diameters shown be checked with the motor manufacturer to be sure they meet their recommendations for minimum pitch diameter. 81

Accessories Shaft Mount Reducers Preselected elt Drives 115SMTP09 8 115SMTP09 Variable 115SMTP09 elt Variable elts elts ushing ushing ushing ushing 16 0 VP6 1 AK 1 5 VP4 1 AK5 T80 T00 6 9 VP50 14 AK6 0 VP56 15 AK 4 8 VP50 16 K8 T00 9 4 VP56 5V4 17 AK5 X 44 46 VP60 18 AK7 47 54 VP4 5V16 19 AK 55 58 VP56 0 AK5 59 64 VP60 1 AK6 5V50 65 70 5V160 AK7 VP65 61 75 K 76 78 VP71 4 5 V1 79 85 VP65 6 7 V QV50 VX 86 95 VP71 5V16 8 9 V6 X 96 0 VP75 0 1 K 1 7 VP65 K4 5V1 8 117 VP71 4 6 K6 K190 118 1 VP65 6 8 K40 14 14 5V90 X 9 40 T8 P1 VP71 14 145 41 4 K X 146 160 VP65 44 45 K4 161 175 VP71 5V74 46 48 T8 K160 P1 176 185 VP75 49 51 T40 186 191 VP65 5 54 K45 5V6 X 19 00 VP71 55 56 K4 5V14 57 58 T8 P1 59 61 K45 6 64 K47 65 66 5V4 P1 X 5V16 67 69 K50 70 7 K5 7 74 5V5 75 78 K5 79 8 K55 84 87 K57 5V14 88 91 K60 9 9 K5 94 99 K55 X 0 K57 K1 4 9 K60 1 11 K6 11 119 K55 K57 11 14 5V5 5V86 15 19 5V54 14 5V56 15 141 5V64 14 145 5V66 5V94 146 149 5V68 150 157 5V64 X 158 16 5V66 K90 16 167 5V68 Notes: Preselected belt drives are based on the following guidelines: NEMA Recommendations for Sheave Diameter and Width 168 5V70 Average Service at Reducer Rated Load 169 171 5V6 elt Minimum 5V74 17 175 5V64 For other conditions (including but not limited to; fire hazard, explosion hazard or 176 186 5V80 choked input), contact Application Engineering (1 800 66 09) for assistance in 187 19 5V6 5V66 selecting a belt drive. 19 198 5V64 It is recommended that 50 hp motors and larger the sheave diameters shown be 199 00 5V86 K90 X checked with the motor manufacturer to be sure they meet their recommendations for minimum pitch diameter. elt

Accessories Shaft Mount Reducers Preselected elt Drives 115SMTP15 115SMTP15 Variable 115SMTP15 elt Variable elts elts ushing ushing ushing ushing 1 VP6 7 K7 14 16 VP4 V5V78 8 K0 17 19 VP50 9 K T80 0 VP6 K6 AK154 8 11 AK VP4 9 AK14 1 AK5 5V50 6 VP50 1 AK7 AK144 7 41 VP56 14 AK 4 50 5V86 15 AK VP4 X 51 58 K80 16 AK6 K190 59 61 17 AK7 VP65 6 6 18 5V1 AK 64 67 X 19 0 VP71 68 69 1 K8 5V16 70 7 VP60 AK5 74 78 K0 VP65 79 81 5V86 X 4 AK0 8 87 5 AK VP71 88 6 7 AK4 AK154 89 9 VP60 8 9 AK9 X 94 1 VP65 0 1 AK41 5V68 6 AK44 VP71 7 111 4 AK4 11 VP65 K6 5 7 AK9 X 11 VP71 5V58 8 9 AK41 AK14 40 4 AK44 4 44 AK46 45 46 AK49 47 49 K4 50 51 K6 X 5 5 T8 54 56 T40 P1 57 58 5V4 59 61 K47 K90 6 6 5V4 P1 64 65 K50 66 68 K5 69 7 K56 7 75 AK59 76 78 AK61 AK94 79 8 AK64 8 85 K57 86 90 K60 K80 91 9 K6 94 99 K55 0 K57 4 8 K60 K67 X 9 111 K6 11 119 K57 K60 11 1 5V5 5V5 1 16 5V54 17 5V68 5V6 X elt Shaft Mount Accessories Notes: Preselected belt drives are based on the following guidelines: NEMA Recommendations for Sheave Diameter and Width Average Service at Reducer Rated Load elt Minimum For other conditions (including but not limited to; fire hazard, explosion hazard or choked input), contact Application Engineering (1 800 66 09) for assistance in selecting a belt drive. It is recommended that 50 hp motors and larger the sheave diameters shown be checked with the motor manufacturer to be sure they meet their recommendations for minimum pitch diameter. 8

Accessories Shaft Mount Reducers Preselected elt Drives 115SMTP5 115SMTP5 Variable 115SMTP5 elt Variable elts elts ushing ushing ushing ushing 6 7 VP6 5 AK0 8 9 VP4 5V78 6 AK 5V78 11 VP50 7 K5 1 14 VP6 8 AK 5V00 AK154 15 16 VP4 9 AK5 17 1 VP6 AK AK4 4 11 K8 K160 5 0 5V86 1 AK6 1 5 K80 1 AK VP4 6 8 14 K8 5V6 5V14 9 41 15 AK6 4 50 5V50 X 16 AK7 51 57 VP50 AK56 17 AK 58 61 VP60 AK61 18 AK 6 67 P65 19 AK5 5V94 K55 68 76 0 AK6 VP60 X 77 80 K50 1 AK7 AK6 4 K 5V86 5 AK41 6 7 AK44 AK114 8 AK46 9 0 AK49 1 AK 4 AK4 AK74 5 AK0 6 7 AK AK64 8 AK4 9 40 K 41 4 K4 44 45 K6 K6 46 47 K40 X 48 50 K 51 54 K4 K50 55 57 K6 58 K40 59 60 AK54 61 6 AK56 64 66 AK59 AK64 67 69 AK61 70 71 AK64 7 AK54 7 75 AK56 AK54 76 78 AK59 79 80 K6 K55 X elt Notes: Preselected belt drives are based on the following guidelines: NEMA Recommendations for Sheave Diameter and Width Average Service at Reducer Rated Load elt Minimum For other conditions (including but not limited to; fire hazard, explosion hazard or choked input), contact Application Engineering (1 800 66 09) for assistance in selecting a belt drive. It is recommended that 50 hp motors and larger the sheave diameters shown be checked with the motor manufacturer to be sure they meet their recommendations for minimum pitch diameter. 84

Accessories Shaft Mount Reducers Preselected elt Drives 115SMTP5 115SMTP5 Variable 115SMTP5 elt Variable elts ushing ushing ushing 5 6 VP6 5 AK0 7 VP4 TA45 6 K8 5V00 8 VP50 7 AK7 9 11 VP6 8 K5 AK14 1 14 9 AK 5V14 15 17 VP4 AK4 AK5 18 0 AK84 11 AK6 1 VP6 1 K5 5V66 6 1 AK 7 VP4 K6 X 14 AK 5V86 8 AK49 15 AK5 9 4 VP50 16 AK7 AK54 4 45 VP56 17 AK 46 50 VP50 AK44 18 AK 5V66 19 0 AK5 1 AK AK 4 AK4 5 6 AK9 7 AK41 8 AK4 9 0 AK9 1 AK41 AK64 AK44 4 5 AK9 6 7 AK41 8 40 AK44 41 4 AK46 AK56 4 44 AK49 45 46 AK51 47 49 AK54 50 AK44 AK44 ushing K60 AK74 elts elt Shaft Mount Accessories Notes: Preselected belt drives are based on the following guidelines: NEMA Recommendations for Sheave Diameter and Width Average Service at Reducer Rated Load elt Minimum For other conditions (including but not limited to; fire hazard, explosion hazard or choked input), contact Application Engineering (1 800 66 09) for assistance in selecting a belt drive. It is recommended that 50 hp motors and larger the sheave diameters shown be checked with the motor manufacturer to be sure they meet their recommendations for minimum pitch diameter. 85

Accessories Shaft Mount Reducers Preselected elt Drives 0SMTP05 0SMTP05 Variable 0SMTP05 elt Variable ushing elts elts ushing ushing ushing 90 99 VP65 90 9 5V46 0 8 VP71 R5V1 9 96 V5V48 9 114 97 0 V5V50 VP75 X 115 5V00 1 5V5 K190 11 19 VP65 5V154 4 7 5V54 141 VP71 8 9 5V56 5V160 14 15 VP75 1 116 5V6 15 165 VP71 117 5V5 5V154 5V16 166 176 V5870 11 1 5V6 177 01 MVP75C97Q 1 16 5V64 K190 X Q TC160 CX 0 04 MVP85C7Q 17 19 5V68 05 15 V5870 5V1 14 5V58 16 8 MVP75C97Q 15 19 5V60 C140R 9 9 MVP85C7Q 140 14 5V6 5V154 40 46 MVP75C97Q 144 147 5V64 Q TC CX 47 7 MVP85C7Q 148 155 5V58 7 79 MVP75C97Q 156 160 5V60 TC114 80 91 MVP85C7Q 161 165 5V6 5V16 X 9 05 MVP7084 MV90Q 166 175 5V66 X 06 4MVP6074 4MV74Q Q 4 176 180 5V68 7 V6880 5V80 181 18 5V70 8 4 MVP95C117Q TC114 184 19 5V74 5V16 5 60 MVP5C17Q 194 00 5V70 Q TC114 CX 5V14 61 87 MVP95C117Q 01 1 5V74 88 400 MVP5C17Q TC98 1 4 5V86 5 4 5V90 5V16 5 44 5V94 45 46 5V60 47 54 5V6 55 6 5V64 5V86 6 71 5V66 7 86 5V60 87 95 5V6 96 05 5V64 5V74 06 08 5V66 09 6 5V80 5V86 7 1 Q4V9 5 5V1 5V1 5 7 5V1 K1 X 7 86 5V16 5V14 87 400 5V1 5V94 X elt Notes: Preselected belt drives are based on the following guidelines: NEMA Recommendations for Sheave Diameter and Width Average Service at Reducer Rated Load elt Minimum For other conditions (including but not limited to; fire hazard, explosion hazard or choked input), contact Application Engineering (1 800 66 09) for assistance in selecting a belt drive. It is recommended that 50 hp motors and larger the sheave diameters shown be checked with the motor manufacturer to be sure they meet their recommendations for minimum pitch diameter. 86

Accessories Shaft Mount Reducers Preselected elt Drives 0SMTP09 0SMTP09 Variable 0SMTP09 elt Variable ushing elts elts ushing ushing ushing 0 4 T00 1 AK T80 VP4 5 9 5V50 1 K8 0 VP50 14 K0 7 9 VP60 15 K 5V78 40 4 VP65 16 K4 T80 4 47 VP71 17 K6 48 5 MVP549 18 K40 X 5 59 VP60 19 0 K45 60 64 VP65 K190 1 K 65 70 VP71 K4 71 74 VP75 4 K6 T00 75 80 VP65 5 6 K40 81 88 VP71 R5V150 7 8 K 89 9 VP75 9 0 K4 9 95 VP71 1 K6 5V16 X 5V4 96 0 VP75 K40 1 8 VP65 K40 9 114 X 4 6 K45 VP71 5V1 115 118 7 9 K40 X 119 15 VP75 40 4 K45 5V00 16 15 VP71 4 45 VP71 Q5V97 16 14 VP75 46 47 T4 P 144 151 VP71 48 50 T6 K160 5V86 15 159 VP75 51 5 T8 P1 161 165 V5870 Q5V85 54 56 K47 166 17 4MVP4559 57 59 K50 4MV64Q Q X 4 174 187 4MVP5964 60 6 K5 K160 188 00 V5870 5V68 6 67 K55 68 69 K57 70 71 5V5 7 75 5V50 76 78 5V5 79 81 5V54 5V16 8 84 5V56 85 87 5V58 88 89 5V54 90 9 5V56 9 95 5V58 96 99 5V60 0 1 5V6 5V14 7 5V64 8 1 5V66 X 111 11 5V68 114 115 5V6 116 118 5V64 119 1 5V66 5V1 1 16 5V68 17 18 5V70 19 16 5V60 17 140 5V6 141 145 5V64 5V90 146 149 5V66 150 154 5V68 155 156 5V66 157 161 5V68 16 165 5V70 5V86 166 175 5V74 176 178 5V70 179 188 5V74 8V80 189 19 5V70 19 00 5V74 5V74 elt Shaft Mount Accessories Notes: Preselected belt drives are based on the following guidelines: NEMA Recommendations for Sheave Diameter and Width Average Service at Reducer Rated Load elt Minimum For other conditions (including but not limited to; fire hazard, explosion hazard or choked input), contact Application Engineering (1 800 66 09) for assistance in selecting a belt drive. It is recommended that 50 hp motors and larger the sheave diameters shown be checked with the motor manufacturer to be sure they meet their recommendations for minimum pitch diameter. 87

Accessories Shaft Mount Reducers Preselected elt Drives 0SMTP15 0SMTP15 Variable 0SMTP15 elt Variable ushing elts ushing ushing 1 VP6 7 AK 5V78 T80 1 15 8 AK5 VP4 16 17 9 AK 18 0 VP50 5V50 AK5 T00 1 4 VP56 11 AK7 5 8 VP50 1 K0 AK184 9 VP56 1 K 5 VP60 14 K4 6 8 VP65 15 K6 K190 9 41 VP71 16 K40 4 44 VP75 17 K0 45 50 VP65 18 K 5V16 51 56 VP71 X 19 K4 57 58 VP60 0 1 K6 59 6 VP65 5V1 K40 K190 6 69 VP71 T8 P1 70 7 VP60 4 K45 74 79 5 K47 VP65 5V86 80 8 6 5V4 8 87 VP71 7 9 T8 P1 88 95 VP65 0 1 T40 5V74 96 1 VP71 5V4 11 VP65 4 K47 5V6 114 1 5 6 K50 VP71 14 5V58 7 K5 K160 8 40 K45 41 4 K47 4 45 K50 46 47 K5 48 49 5V48 50 5 K57 5 55 K60 56 57 K6 58 59 K55 60 61 K57 6 65 K60 66 67 K6 68 71 K55 7 74 K57 75 78 K60 5V86 79 80 K6 81 85 5V6 86 88 5V64 89 90 5V66 5V90 91 9 5V68 94 98 5V64 99 1 5V66 5V80 4 5V68 5 6 5V64 7 9 5V66 1 11 5V68 11 118 5V64 119 11 5V66 5V66 1 15 5V68 16 18 5V66 5V6 19 5V64 5V58 ushing K190 5V14 K1 K80 elts X elt Notes: Preselected belt drives are based on the following guidelines: NEMA Recommendations for Sheave Diameter and Width Average Service at Reducer Rated Load elt Minimum For other conditions (including but not limited to; fire hazard, explosion hazard or choked input), contact Application Engineering (1 800 66 09) for assistance in selecting a belt drive. It is recommended that 50 hp motors and larger the sheave diameters shown be checked with the motor manufacturer to be sure they meet their recommendations for minimum pitch diameter. 88

Accessories Shaft Mount Reducers Preselected elt Drives 0SMTP5 0SMTP5 Variable 0SMTP5 elt Variable ushing elts ushing ushing ushing 6 7 VP6 5 K5 8 9 VP4 5V78 6 AK 5V78 11 VP50 7 AK7 1 14 VP4 8 K5 15 17 VP50 AK184 9 AK K190 18 19 VP56 AK5 0 VP4 4V1 11 AK8 4 7 VP50 1 AK0 AK114 8 VP56 1 AK4 AK184 5 VP60 14 AK9 AK4 6 8 VP65 15 AK41 9 4 VP60 16 AK44 44 48 VP65 5V86 17 AK4 49 5 VP71 18 19 AK9 5 55 VP60 0 AK41 5V68 56 61 VP65 1 AK44 AK144 6 69 VP60 X AK46 5V54 70 71 VP65 4 AK49 7 80 VP60 5V46 5 6 AK9 7 AK41 AK4 8 9 AK9 0 AK41 AK94 1 T8 4 P1 5 6 T40 K90 7 5V4 8 9 K50 40 41 K5 4 44 K50 45 46 K5 47 49 K55 50 51 K57 K80 5 5 K60 54 55 K6 56 59 K55 60 61 K57 6 64 K60 K67 65 66 K6 67 69 K57 70 7 K60 5V54 7 75 K6 76 80 K60 K55 elts X elt Shaft Mount Accessories Notes: Preselected belt drives are based on the following guidelines: NEMA Recommendations for Sheave Diameter and Width Average Service at Reducer Rated Load elt Minimum For other conditions (including but not limited to; fire hazard, explosion hazard or choked input), contact Application Engineering (1 800 66 09) for assistance in selecting a belt drive. It is recommended that 50 hp motors and larger the sheave diameters shown be checked with the motor manufacturer to be sure they meet their recommendations for minimum pitch diameter. 89

Accessories Shaft Mount Reducers Preselected elt Drives 0SMTP5 0SMTP5 Variable 0SMTP5 elt Variable ushing elts ushing 5 6 VP6 5 K5 7 VP4 TA45 6 AK 8 VP50 7 AK7 9 11 VP6 8 K6 5V16 1 1 9 AK 14 16 VP4 AK114 K8 17 19 AK94 11 AK6 0 1 VP50 1 AK AK4 4 VP56 1 AK4 5 0 K67 14 AK9 1 6 VP4 K55 15 AK41 7 8 K47 16 AK44 9 4 VP60 17 AK46 5V6 44 47 VP65 18 AK49 48 50 VP60 5V5 19 AK51 0 AK9 1 AK41 AK44 4 AK46 5 6 K 7 8 K4 9 K6 0 1 K K4 4 5 K 6 7 K4 8 K6 9 K45 40 41 K47 4 44 K50 45 47 AK54 48 49 AK56 50 AK59 ushing 5V00 5V14 AK14 AK94 ushing 5V6 K57 5V46 5V5 elts X AK59 elt Notes: Preselected belt drives are based on the following guidelines: NEMA Recommendations for Sheave Diameter and Width Average Service at Reducer Rated Load elt Minimum For other conditions (including but not limited to; fire hazard, explosion hazard or choked input), contact Application Engineering (1 800 66 09) for assistance in selecting a belt drive. It is recommended that 50 hp motors and larger the sheave diameters shown be checked with the motor manufacturer to be sure they meet their recommendations for minimum pitch diameter. 90

Accessories Shaft Mount Reducers Preselected elt Drives 07SMTP05 07SMTP05 Variable 07SMTP05 elt Variable ushing elts elts ushing ushing ushing 90 96 VP71 90 91 45V46 5V4 97 1 VP75 9 95 45V48 111 VP65 96 99 45V50 45V184 4 11 1 VP71 0 1 45V5 5V184 1 15 VP75 4 45V54 16 19 V5870 5 1 45V56 17 V6880 5V00 111 11 5V58 X 18 148 V5870 5V160 114 11 5V6 149 160 V5870 R5V150 1 15 5V64 161 168 V6880 5V160 16 19 5V66 K190 169 177 5V140 1 5V68 V5870 178 187 5V14 1 16 5V70 188 198 5V16 17 148 5V74 199 07 Q5V1 149 151 5V66 08 19 v6880 Q5V15 15 155 5V68 5V154 0 Q5V118 156 160 5V70 46 5V1 161 16 5V74 47 5 MVP5C17Q TC160 16 165 5V58 54 7 MVP95C117Q 166 170 5V60 C140R 7 94 171 176 5V6 MVP5C17Q 5V14 95 15 TC 177 181 5V64 16 1 TC114 18 187 5V66 MVP95C117Q Q CX 40 TC6 188 19 5V68 41 57 MVP85C7Q MVC96Q 194 196 5V86 58 6 MVP75C97Q 197 05 5V90 5V154 Q 6 81 MVP80CQ MV86Q 06 5V94 8 400 MVP85C7Q 11 5V86 5V90 5V16 4 5V94 4 46 Q5V97 47 5 54 58 45V64 45V86 4 59 71 Q5V97 7 85 Q5V 86 0 Q5V9 5V14 0 5V1 11 1 Q5V 9 Q5V9 5V1 0 40 5V1 41 49 5V14 50 61 Q5V1 5V14 6 8 5V16 84 9 5V14 5V1 94 400 Q5V1 elt Shaft Mount Accessories Notes: Preselected belt drives are based on the following guidelines: NEMA Recommendations for Sheave Diameter and Width Average Service at Reducer Rated Load elt Minimum For other conditions (including but not limited to; fire hazard, explosion hazard or choked input), contact Application Engineering (1 800 66 09) for assistance in selecting a belt drive. It is recommended that 50 hp motors and larger the sheave diameters shown be checked with the motor manufacturer to be sure they meet their recommendations for minimum pitch diameter. 91

Accessories Shaft Mount Reducers Preselected elt Drives 07SMTP09 07SMTP09 Variable 07SMTP09 elt Variable ushing elts elts ushing ushing ushing 5 MVP549 T80 15 K 6 9 MVP549 16 K4 MV00R 0 1 MVP4054 17 K6 4 MVP549 18 K40 T80 5 9 VP60 19 0 K45 40 4 VP65 5V78 1 K47 44 47 VP71 X K50 48 50 VP75 K5 51 55 VP71 4 5 T6 P 5V4 56 58 VP75 6 7 K45 59 60 VP65 8 T6 P 61 65 VP71 5V00 9 0 K45 5V78 X 66 69 VP75 1 K50 70 75 VP65 K5 5V160 76 79 VP71 K55 80 84 MVP4559 4 5 K5 85 90 MVP5064 6 7 K55 5V78 X MV16R X 91 97 MVP5569 8 9 K57 98 4 MVP6074 40 4T8 5 11 MVP85C7Q C180R 41 4 4T40 114 116 MVP75C97Q Q CX 4 44 4T8 TC160 P1 117 18 MVP85C7Q 45 46 4T40 19 15 V6880 Q5V118 47 49 45V4 16 146 V5870 Q5V97 50 51 45V44 45V184 X 4 147 15 MVP75C97Q 5 5 45V50 TC 154 156 VMP85C7Q Q CX 54 56 45V5 157 171 MVP5C17Q C140R 57 58 5V44 P1 17 184 4MV86Q 59 61 5V46 4MVP7084 Q X 4 185 00 4MV80Q 6 64 5V48 5V154 65 67 5V50 68 69 5V5 70 74 5V56 75 76 5V58 5V160 X 77 79 5V60 80 84 5V66 85 87 5V68 88 90 5V70 5V160 91 95 5V74 96 1 5V54 5V56 4 8 5V58 9 11 5V60 11 115 5V6 5V1 116 119 5V64 1 5V66 14 15 5V68 16 19 5V86 15 5V90 5V16 16 141 5V94 14 14 5V60 144 147 5V6 5V86 148 15 5V64 15 156 5V86 5V1 Notes: Preselected belt drives are based on the following guidelines: 157 158 Q5V97 NEMA Recommendations for Sheave Diameter and Width 159 166 Q5V Average Service at Reducer Rated Load 5V14 167 171 Q5V9 elt Minimum 17 181 5V1 For other conditions (including but not limited to; fire hazard, explosion hazard or 18 187 Q5V choked input), contact Application Engineering (1 800 66 09) for assistance in 188 19 Q5V9 selecting a belt drive. 19 00 5V1 5V1 It is recommended that 50 hp motors and larger the sheave diameters shown be checked with the motor manufacturer to be sure they meet their recommendations for minimum pitch diameter. 9 elt

Accessories Shaft Mount Reducers Preselected elt Drives 07SMTP15 07SMTP15 Variable 07SMTP15 elt Variable ushing elts ushing ushing 11 1 7 K7 VP4 T80 14 16 8 K0 17 19 VP50 9 K T80 0 VP60 K6 5V78 4 5 VP65 11 T8 P1 6 8 VP71 1 K45 9 VP6 1 K6 4 5 VP65 5V00 X 14 T8 6 9 VP71 15 T40 P1 40 44 VP65 16 5V4 45 48 VP71 5V160 17 K 49 51 VP75 18 K4 5 57 VP71 5V16 19 K6 58 61 VP65 0 K40 Q5V118 6 69 VP71 1 70 74 VP65 T8 P1 Q5V97 75 8 VP71 4 84 91 5V90 5 6 K47 9 99 Q5V85 7 8 K50 K190 V5870 0 5 Q5V80 9 K5 6 1 5V74 0 1 K55 111 116 5V80 K55 117 119 Q5V80 4 5 K57 V6880 16 5V74 6 7 K60 K190 17 5V70 8 40 5V58 41 4 K5 4 45 5V50 46 47 5V5 5V16 48 50 5V56 51 5 5V54 54 55 5V56 56 57 5V58 58 60 5V8 5V14 61 6 5V64 64 67 5V68 68 71 5V64 7 75 5V68 5V1 76 78 5V60 79 8 5V64 84 88 5V68 5V94 89 91 5V70 9 96 5V74 97 99 5V70 0 5 5V74 5V86 6 111 5V86 11 116 5V90 5V94 117 1 5V94 1 16 5V90 17 5V94 5V86 ushing elts elt T00 5V00 X Shaft Mount Accessories Notes: Preselected belt drives are based on the following guidelines: NEMA Recommendations for Sheave Diameter and Width Average Service at Reducer Rated Load elt Minimum For other conditions (including but not limited to; fire hazard, explosion hazard or choked input), contact Application Engineering (1 800 66 09) for assistance in selecting a belt drive. It is recommended that 50 hp motors and larger the sheave diameters shown be checked with the motor manufacturer to be sure they meet their recommendations for minimum pitch diameter. 9

Accessories Shaft Mount Reducers Preselected elt Drives 07SMTP5 07SMTP5 Variable 07SMTP5 elt Variable ushing elts ushing ushing 6 7 VP6 5 K0 8 9 VP4 6 K6 5V78 11 VP50 7 K8 1 1 VP56 8 K 14 16 VP4 9 K6 17 0 VP50 K8 P1 1 VP60 5V160 11 T40 4 5 VP65 1 AK0 6 8 VP71 1 AK4 9 1 VP65 14 AK9 AK14 4 VP71 15 AK41 5 8 VP65 16 AK44 5V1 9 40 VP71 17 AK46 41 4 VP60 18 K4 4 47 VP65 5V90 19 K6 X 48 51 VP71 0 K40 P1 5 57 VP65 1 T8 58 6 VP71 5V74 K45 6 66 VP75 K47 67 68 VP65 4 K50 5V6 69 74 VP71 5 K47 75 80 VP65 5V5 6 7 K50 8 K5 9 K55 0 1 5V5 K6 4 5 K55 6 7 5V5 8 40 K6 41 4 K55 4 44 5V5 45 46 5V54 47 48 5V6 49 51 5V66 5 5 5V68 54 57 5V6 58 60 5V66 61 6 5V68 6 65 5V80 66 69 5V66 70 74 5V60 75 78 5V64 79 80 5V66 ushing T80 5V50 AK184 5V16 5V14 K1 5V86 K0 5V80 5V90 elts X X elt K65 Notes: Preselected belt drives are based on the following guidelines: NEMA Recommendations for Sheave Diameter and Width Average Service at Reducer Rated Load elt Minimum For other conditions (including but not limited to; fire hazard, explosion hazard or choked input), contact Application Engineering (1 800 66 09) for assistance in selecting a belt drive. It is recommended that 50 hp motors and larger the sheave diameters shown be checked with the motor manufacturer to be sure they meet their recommendations for minimum pitch diameter. 94

Accessories Shaft Mount Reducers Preselected elt Drives 07SMTP5 07SMTP5 Variable 07SMTP5 elt Variable ushing elts ushing ushing ushing 5 VP6 5 AK5 5V50 6 VP4 6 K4 5V78 7 8 VP50 7 AK 9 VP56 8 K0 11 VP4 9 K 5V160 1 14 VP50 5V160 K6 15 VP56 11 K40 16 VP4 1 AK 17 0 VP50 AK114 1 AK4 1 VP60 14 AK9 4 7 VP65 15 AK41 5V1 8 0 VP71 16 AK44 AK14 1 4 VP65 17 AK46 5 6 VP65 5V80 18 AK49 7 40 VP71 X 19 AK51 41 44 VP60 0 AK46 5V60 45 47 VP65 1 AK49 48 50 VP71 K67 AK51 AK54 AK114 4 AK56 5 6 AK59 7 AK64 8 5V48 9 0 K55 1 K57 5V86 K60 4 K6 5 5V48 6 7 K55 5V68 8 9 K57 40 K60 41 44 K55 K65 45 46 5V66 47 5V68 K80 48 50 5V64 5V66 elts X elt Shaft Mount Accessories Notes: Preselected belt drives are based on the following guidelines: NEMA Recommendations for Sheave Diameter and Width Average Service at Reducer Rated Load elt Minimum For other conditions (including but not limited to; fire hazard, explosion hazard or choked input), contact Application Engineering (1 800 66 09) for assistance in selecting a belt drive. It is recommended that 50 hp motors and larger the sheave diameters shown be checked with the motor manufacturer to be sure they meet their recommendations for minimum pitch diameter. 95

Accessories Shaft Mount Reducers Preselected elt Drives 15SMTP05 15SMTP05 Variable 15SMTP05 elt Variable ushing elts ushing ushing 90 98 V5870 90 96 45V50 5V50 99 111 V5880 97 99 45V5 11 117 5V00 0 45V54 V5870 118 5V184 4 7 45V56 45V184 11 19 MVP5C17Q C00R 8 111 5V58 140 14 VMP95C117Q C70R 11 118 5V6 14 154 119 1 5V64 MVP4C17Q TC40 155 178 1 5V68 179 194 MVP95C117Q 11 14 5V70 TC00 195 1 15 141 5V74 MVP5C17Q 1 0 C180R 14 144 R5V80 1 40 MVP85C7Q Q CX 145 15 5V80 41 6 MVP90C11Q MVC140R 15 16 4Q5V59 6 81 MVP95C117Q 16 170 45V60 8 1 MVP85C7Q 171 181 45V64 14 4 MVC1Q 18 19 45V68 MVP90C11Q 5 7 Q 19 198 4V5V70 8 75 MVCQ 199 09 45V74 MVP115C17Q 76 400 MVC1Q 5V86 5V90 41 5V94 4 48 R5V97 49 61 R5V 5V16 6 76 R5V9 77 8 5V1 84 91 R5V118 9 05 R5V97 06 0 R5V 5V1 1 8 R5V9 9 7 5V1 8 49 5V14 50 65 R5V1 5V14 66 8 5V16 8 400 5V14 R5V9 ushing elts elt 5V184 45V14 4 4 Notes: Preselected belt drives are based on the following guidelines: NEMA Recommendations for Sheave Diameter and Width Average Service at Reducer Rated Load elt Minimum For other conditions (including but not limited to; fire hazard, explosion hazard or choked input), contact Application Engineering (1 800 66 09) for assistance in selecting a belt drive. It is recommended that 50 hp motors and larger the sheave diameters shown be checked with the motor manufacturer to be sure they meet their recommendations for minimum pitch diameter. 96

Accessories Shaft Mount Reducers Preselected elt Drives 15SMTP09 15SMTP09 Variable 15SMTP09 elt Variable ushing elts ushing ushing 0 4 MVP549 0 T6 P MV80R 5 9 MVP4054 1 T8 P1 0 5 MVP4054 T40 6 8 MVP4599 K47 MV00R 9 41 MVP5064 X 4 K50 4 46 MVP5569 5 K5 47 51 MVP5569 6 7 5V48 MV50R 5 57 MVP6074 8 5V50 58 6 MVP75C97Q 9 5V5 6 68 MVP85C7Q 0 5V54 C00R 69 74 MVP95C117Q 1 5V56 75 81 MVP5C17Q 5V4 8 86 MVP85C7Q 4 5V44 TC40 87 9 MVP95C117Q 5 5V48 9 MVP75C97Q 6 7 5V50 Q CX 4 11 MVP85C7Q MVC180R 8 5V5 114 1 MVP95C117Q 9 40 5V46 14 14 MVP75C97Q 41 4 5V48 14 161 MVP90C11Q 4 5V50 16 17 MVP95C117Q MVCQ Q 44 45 5V5 17 189 MVP5C17Q 46 47 5V54 190 00 MVP115C17Q 48 49 5V56 50 5 5V60 5 54 5V6 55 56 5V64 57 58 45V5 59 60 45V54 61 6 45V56 6 64 45V58 65 68 45V60 69 7 45V64 74 75 45V66 76 78 5V70 79 8 5V74 8 84 R5V80 85 89 5V80 90 94 4Q5V59 95 99 45V60 0 4 45V64 5 1 R5V85 111 114 5V86 115 119 5V90 14 5V94 15 1 R5V90 1 15 R5V9 16 144 R5V97 145 151 R5V 15 160 R5V9 161 165 5V1 166 176 R5V9 177 181 5V1 18 186 5V14 187 19 R5V1 19 00 5V16 ushing T80 5V78 5V4 elts X elt 45V184 4 5V184 X 45V14 4 5V154 5V16 5V14 5V16 Shaft Mount Accessories Notes: Preselected belt drives are based on the following guidelines: NEMA Recommendations for Sheave Diameter and Width Average Service at Reducer Rated Load elt Minimum For other conditions (including but not limited to; fire hazard, explosion hazard or choked input), contact Application Engineering (1 800 66 09) for assistance in selecting a belt drive. It is recommended that 50 hp motors and larger the sheave diameters shown be checked with the motor manufacturer to be sure they meet their recommendations for minimum pitch diameter. 97

Accessories Shaft Mount Reducers Preselected elt Drives 15SMTP15 15SMTP15 Variable 15SMTP15 elt Variable ushing elts ushing ushing 11 14 VP4 T80 9 K 15 19 MVP549 T00 K6 0 11 T8 P1 VP60 4 5 1 K45 X 6 8 VP65 5V50 1 K50 9 VP71 14 K5 4 MVP6074P P 15 T6 P 5 9 VP71 16 T40 P1 40 44 VP75 5V00 17 5V4 45 48 V6880 18 K50 49 54 V5870 R5V160 19 K5 55 61 MVP75C97Q 0 K50 6 67 MVP85C7Q Q C180R CX 1 K5 68 75 MVP95C117Q K55 76 86 V5870 Q5V97 K57 87 94 MVP95C117Q 4 5 4T6 P C140R 95 MVP5C17Q 6 4T8 Q CX 118 MVP85C7Q TC6 7 8 4T40 P1 119 MVP80C MVC86Q Q 9 0 45V44 1 45V46 4 5V4 5 7 5V46 8 40 5V50 41 4 5V48 44 47 5V5 48 51 5V56 5 54 5V68 55 57 5V74 58 60 Q5V80 61 6 5V80 64 66 Q5V85 67 68 5V86 69 7 5V80 7 77 5V86 78 81 5V90 8 84 5V94 85 86 Q5V90 87 89 Q5V9 90 94 Q5V97 95 99 Q5V 0 5 Q5V9 6 8 5V1 9 11 Q5V 11 114 Q5V9 115 118 5V1 119 1 5V14 1 15 Q5V1 16 5V16 ushing T80 5V78 5V78 elts elt X 45V154 4 5V154 5V16 5V154 5V16 5V14 5V1 5V14 Notes: Preselected belt drives are based on the following guidelines: NEMA Recommendations for Sheave Diameter and Width Average Service at Reducer Rated Load elt Minimum For other conditions (including but not limited to; fire hazard, explosion hazard or choked input), contact Application Engineering (1 800 66 09) for assistance in selecting a belt drive. It is recommended that 50 hp motors and larger the sheave diameters shown be checked with the motor manufacturer to be sure they meet their recommendations for minimum pitch diameter. 98

Accessories Shaft Mount Reducers Preselected elt Drives 15SMTP5 15SMTP5 Variable 15SMTP5 elt Variable ushing elts ushing ushing 7 8 VP4 5 K0 T00 9 6 K6 VP50 11 1 7 T40 P1 1 14 VP60 8 T50 TA45 15 16 VP65 9 T8 17 18 VP71 T40 19 1 VP65 11 K6 MVP5064 1 K40 5V184 4 5 1 T8 VP75 P1 6 8 14 5V4 9 VP65 15 T6 P R5V140 5 VP75 16 17 K45 6 8 VP65 18 5V4 P1 5V1 9 4 VP71 19 K50 44 50 V5870 0 K5 Q5V 51 58 V6880 1 T6 P 59 69 V5870 5V74 T8 P1 70 80 V6870 Q5V75 4 5 K47 6 5V44 P1 7 8 5V46 9 5V48 0 1 5V58 5V6 4 5 5V66 6 5V66 7 8 5V58 9 41 5V6 4 4 5V66 44 46 5V70 47 49 5V74 50 5 5V80 5 54 5V70 55 56 5V74 57 58 Q5V80 59 6 5V80 6 65 5V86 66 69 70 7 5V90 7 75 5V94 76 77 5V86 78 80 Q5V9 ushing T80 P1 5V78 5V00 5V160 5V14 5V16 5V1 5V94 5V90 5V80 elts X elt Shaft Mount Accessories Notes: Preselected belt drives are based on the following guidelines: NEMA Recommendations for Sheave Diameter and Width Average Service at Reducer Rated Load elt Minimum For other conditions (including but not limited to; fire hazard, explosion hazard or choked input), contact Application Engineering (1 800 66 09) for assistance in selecting a belt drive. It is recommended that 50 hp motors and larger the sheave diameters shown be checked with the motor manufacturer to be sure they meet their recommendations for minimum pitch diameter. 99

Accessories Shaft Mount Reducers Preselected elt Drives 15SMTP5 15SMTP5 Variable 15SMTP5 elt Variable ushing elts ushing ushing ushing 5 6 VP4 5 K 7 VP50 T00 6 K6 5V78 8 VP56 7 T40 9 VP4 8 5V4 P1 5V00 11 VP50 9 T8 1 VP56 5V00 1 14 VP65 11 K4 15 17 MVP5569 1 K6 18 0 VP60 1 T6 P 5V16 1 MVP5064 14 K45 5V16 4 5 15 L47 VP65 6 8 5V1 16 K50 X 9 VP75 17 K5 6 VP65 18 K55 5V86 7 41 VP75 19 0 K5 4 46 VP65 1 K55 5V68 47 50 V5870 K57 4 K6 5 K65 5V14 6 7 5V64 8 5V66 9 5V70 0 1 5V50 5V54 5V86 4 6 5V86 7 5V90 5V14 8 9 5V94 40 4 5V60 5V74 4 44 5V80 45 46 5V86 47 48 5V90 5V94 49 50 5V94 elts elt X Notes: Preselected belt drives are based on the following guidelines: NEMA Recommendations for Sheave Diameter and Width Average Service at Reducer Rated Load elt Minimum For other conditions (including but not limited to; fire hazard, explosion hazard or choked input), contact Application Engineering (1 800 66 09) for assistance in selecting a belt drive. It is recommended that 50 hp motors and larger the sheave diameters shown be checked with the motor manufacturer to be sure they meet their recommendations for minimum pitch diameter. 0

Accessories Shaft Mount Reducers Preselected elt Drives 07SMTP05 07SMTP05 Variable 07SMTP05 elt Variable ushing ushing elts elts ushing ushing 90 99 MVP85C7Q 90 91 45V60 MVC60R 0 8 MVP95C117Q R CX 9 97 45V64 9 1 MVP85C7Q MVC00R 98 0 45V66 1 14 MVP815V95Q 1 45V68 45V4 15 148 MVP915V5Q 4 6 45V70 MV5V40S S1 149 161 MVP15V115Q 7 11 45V74 Q 16 177 MVP1115V15Q 11 117 45V66 178 194 MVP15V115Q 118 11 45V68 MV5V00R 195 1 MVP15V15Q 1 15 45V70 14 7 MVP1115V15Q MV5V180R 16 45V74 8 6 MVP15V115Q 11 18 45V80 MV5V150R 6 80 MVP15V15Q 19 14 45V80 45V00 81 96 4MV5V1R 14 147 4R5V85 4MVP15V115 97 148 15 45V86 4MV5V118R 4 6 15 158 45V90 4MVP1115V15 6 94 4MV59R 159 165 45V86 95 400 5MVP15V115 5MV5V97R R 5 166 17 45V90 17 180 45V94 181 18 4R5V97 45V184 184 19 4R5V 194 196 4R5V9 4 197 06 45V90 07 15 45V94 16 19 4R5V97 0 8 4R5V 45V154 9 45V90 4 4 45V94 45V16 44 48 4R5V97 49 55 45V90 56 67 45V94 45V14 68 7 4R5V97 74 79 4R5V 80 97 4R5V1 98 05 4R5V140 45V154 06 18 4R5V15 19 6 4R5V1 45V16 7 5 4R5V140 54 68 4R5V1 69 88 4R5V140 45V14 89 94 4R5V15 45V1 95 400 55V14 5R5V9 5 elt Shaft Mount Accessories Notes: Preselected belt drives are based on the following guidelines: NEMA Recommendations for Sheave Diameter and Width Average Service at Reducer Rated Load elt Minimum For other conditions (including but not limited to; fire hazard, explosion hazard or choked input), contact Application Engineering (1 800 66 09) for assistance in selecting a belt drive. It is recommended that 50 hp motors and larger the sheave diameters shown be checked with the motor manufacturer to be sure they meet their recommendations for minimum pitch diameter. 1

Accessories Shaft Mount Reducers Preselected elt Drives 07SMTP09 07SMTP09 Variable 07SMTP09 elt Variable ushing ushing elts elts ushing ushing 7 5MVP4054 4 45V4 P1 5MV80R 8 0 5MVP4559 5 45V46 4S5V75 S1 4 1 5 5MVP4054 6 45V48 5 6 41 5MVP5064 7 8 45V50 5MV00R X 4 45 5MVP5569 9 55V5 46 48 5MVP6074 0 5T54 R 49 55 MVP80CQ 1 5T56 56 59 MVP90C11Q 5T58 5T80 Q X 5 60 6 MVP95C117Q 5T60 MVC60R CX 64 69 MVP85C7Q 4 5T6 70 75 MVP95C117Q 5 5T64 76 81 MVP5C17Q 6 7 45V50 Q 8 94 MVP815V95Q 8 45V5 95 4 MVP915V5Q MV5V00R 9 40 45V54 5 114 MVP15V115Q 41 45V56 45V78 115 MV5V160R 4 4 45V58 11 146 MVP915V5Q MV5V140R 44 46 45V6 147 155 MV5V1R 47 49 45V66 4 156 170 4MV5V1R 50 51 45V58 4MVP15V115 171 18 4 5 54 45V6 4MV5V15R 18 00 4MVP1115V15 55 56 45V64 57 45V66 45V4 58 60 45V68 61 6 45V70 6 65 45V74 66 68 R5V85 69 71 5V86 7 74 5V90 75 77 5V94 5V50 78 79 R5V97 80 8 R5V 84 87 4R5V80 88 9 4R5V85 94 96 45V86 97 0 45V90 1 5 45V94 45V184 4 6 7 4R5V97 8 11 4R5V 114 115 4R5V9 116 1 45V1 14 19 R5V118 17 R5V15 5V184 18 140 R5V1 141 149 45V90 150 155 45V94 45V14 156 164 4R5V15 165 17 4R5V1 45V154 4 174 178 4R5V140 179 185 4R5V15 186 196 4R5V1 45V16 197 00 4R5V140 elt Notes: Preselected belt drives are based on the following guidelines: NEMA Recommendations for Sheave Diameter and Width Average Service at Reducer Rated Load elt Minimum For other conditions (including but not limited to; fire hazard, explosion hazard or choked input), contact Application Engineering (1 800 66 09) for assistance in selecting a belt drive. It is recommended that 50 hp motors and larger the sheave diameters shown be checked with the motor manufacturer to be sure they meet their recommendations for minimum pitch diameter.

Accessories Shaft Mount Reducers Preselected elt Drives 07SMTP15 07SMTP15 Variable 07SMTP15 elt Variable ushing ushing elts ushing 15 16 4MV80R 1 T6 P 17 19 4MVP4054 1 K45 0 14 5V4 P1 4 1 4MVP4559 4MV00R 15 5V46 X 5 4MVP5064 16 5V48 6 7 4MVP6074 17 45V4 P1 8 0 MVP75C971 18 45V44 C60R 1 5 MVP85C7Q 19 45V46 6 4 MVP75C97Q 0 1 45V50 4 46 MVP85C7Q 5V54 C70R 47 49 MVP95C117Q 5V56 CX 50 5 MVP5C17Q 4 5V58 54 61 MVP75C97Q 5 6 5V54 Q 6 67 MVP85C7Q MVC180R 7 5V56 68 7 MVP95C117Q 8 9 4Q5V46 Q 74 8 MVP95C117Q MVC160R 0 45V46 8 9 MVP815V95Q 1 45V48 MV5V118R 9 4 MVP915V5Q 45V50 5 119 MVP915V5Q 4 5 45V54 MV5VR MVP15V115Q 6 7 45V56 8 9 5V60 40 4 5V64 4 Q5V71 44 46 5V70 47 48 5V74 49 R5V80 50 5 5V80 5 55 5V70 56 58 5V74 59 6 45V70 6 65 45V74 66 67 5V86 68 70 5V90 71 7 5V94 74 78 45V80 79 8 45V86 84 87 45V90 88 91 45V94 9 9 R5V97 94 98 R5V 99 4 R5V9 5 9 5V14 1 11 R5V1 114 119 5V14 16 R5V1 17 5V16 T80 ushing elts elt X 4T00 4 T00 5V50 45V184 4 5V184 5V154 45V16 5V154 45V14 5V14 5V16 5V14 4 Shaft Mount Accessories Notes: Preselected belt drives are based on the following guidelines: NEMA Recommendations for Sheave Diameter and Width Average Service at Reducer Rated Load elt Minimum For other conditions (including but not limited to; fire hazard, explosion hazard or choked input), contact Application Engineering (1 800 66 09) for assistance in selecting a belt drive. It is recommended that 50 hp motors and larger the sheave diameters shown be checked with the motor manufacturer to be sure they meet their recommendations for minimum pitch diameter.

Accessories Shaft Mount Reducers Preselected elt Drives 07SMTP5 07SMTP5 Variable 07SMTP5 elt Variable ushing ushing elts ushing 7 9 T80 6 K6 MVP549 1 7 K45 1 14 VP60 5V78 8 K50 15 17 VP71 X 9 T6 P 18 0 VP75 K47 1 MVP7084P P 5V50 11 K50 5V78 4 7 MVP8094Q 1 K50 8 MVP75C97Q 1 K55 4 7 MVP85C7Q 14 K60 5V78 TC00 8 41 MVP95C117Q 15 5V56 4 4 MVP5C17Q 16 5V60 Q 44 5 MVP95C117Q TC160 CX 17 5V4 P1 5 56 MVP95C117Q 18 5V44 C140R 5V184 57 60 MVP5C17Q 19 5V46 61 7 MVP80CQ 0 5V50 MVC96Q Q 74 80 MVP95C117Q 1 5V46 5V48 4 5V5 5 5V54 5V154 6 65V66 7 8 5V60 9 0 5V56 1 5V60 4 5V64 5V16 5 6 5V68 7 8 5V58 9 41 5V6 4 4 5V66 5V1 44 46 5V70 47 49 5V74 50 51 Q5V97 5 54 Q5V 55 Q5V9 56 59 5V1 60 5V80 61 64 R5V85 65 R5V90 5V94 66 69 5V90 70 7 5V94 7 76 5V90 5V86 77 78 5V94 79 80 R5V9 5V94 ushing T80 elts elt X 5V16 Notes: Preselected belt drives are based on the following guidelines: NEMA Recommendations for Sheave Diameter and Width Average Service at Reducer Rated Load elt Minimum For other conditions (including but not limited to; fire hazard, explosion hazard or choked input), contact Application Engineering (1 800 66 09) for assistance in selecting a belt drive. It is recommended that 50 hp motors and larger the sheave diameters shown be checked with the motor manufacturer to be sure they meet their recommendations for minimum pitch diameter. 4

Accessories Shaft Mount Reducers Preselected elt Drives 07SMTP5 07SMTP5 Variable 07SMTP5 elt Variable ushing ushing elts elts ushing ushing 5 6 VP4 5 K4 T00 7 8 MVP549 6 T0 T00 P1 9 15 P65 5V4 7 5V4 X 16 18 VP75 5V184 8 5V48 19 5V154 9 5V5 5V78 VP71 4 5V60 5 7 V5870 5V16 11 K55 X 8 0 V5880 1 K57 5V4 1 4 V5870 1 K6 Q5V9 5 8 V6880 14 5V44 P1 9 4 V5870 15 5V48 5V86 4 46 V6880 16 5V50 47 50 MVP85C7Q Q TC0 CX 17 5V5 18 5V56 5V160 19 5V60 0 5V6 1 5V68 5V60 4 5V64 5 6 5V68 7 8 5V74 5V16 9 0 5V80 1 5V86 4 5V90 5 5V94 6 8 5V80 9 40 5V86 5V1 41 5V90 4 44 5V94 45 46 Q5V 47 48 5V80 5V86 49 50 5V86 elt Shaft Mount Accessories Notes: Preselected belt drives are based on the following guidelines: NEMA Recommendations for Sheave Diameter and Width Average Service at Reducer Rated Load elt Minimum For other conditions (including but not limited to; fire hazard, explosion hazard or choked input), contact Application Engineering (1 800 66 09) for assistance in selecting a belt drive. It is recommended that 50 hp motors and larger the sheave diameters shown be checked with the motor manufacturer to be sure they meet their recommendations for minimum pitch diameter. 5

Accessories Shaft Mount Reducers Preselected elt Drives 15SMTP05 15SMTP05 Variable 15SMTP05 elt Variable ushing ushing elts ushing 90 98 MVP75C97Q MVC60R R CX 90 94 5V94 99 11 MVP815V95Q 95 0 R5V 11 1 MVP915V5Q MV5V00S 1 6 R5V9 14 17 MVP15V115Q Q 7 1 45V74 S1 18 155 MVP915V5Q 111 11 4R5V80 156 171 MVP15V115Q MV5V40S 11 119 45V80 17 186 MVP1115V15Q 16 45V86 187 04 4MV5V00R 17 14 45V90 4MVP15V115 05 7 4 15 19 45V94 4MV5V180R 8 46 4MVP1115V15 140 14 4R5V97 47 66 5MVP915V5 14 148 4R5V 5MV5V140S 67 95 149 155 R5V118 5MVP15V115 96 7 S1 156 165 5V14 5MV5V15S 5 8 56 166 168 R5V1 57 79 5MVP1115V15 5MV5V118S 169 177 4R5V90 80 400 5MV5V198R 178 18 4R5V9 184 186 45V94 187 189 55V94 190 19 5R5V97 194 0 5R5V 04 08 5R5V9 09 1 55V1 1 4R5V118 4 47 4R5V15 48 56 4R5V1 57 70 5R5V118 71 86 55V14 87 97 5R5V1 98 0 55V16 0 15 5516 16 1 5R5V15 4 55V14 5 45 6R5V118 46 48 6S5V15 S1 49 69 65V14 70 81 6S5V1 S1 8 400 65V16 ushing S5V75 S1 45V50 elts elt 5V78 45V184 4 55V184 5 45V184 4 55V160 55V16 65V14 6 4 5 Notes: Preselected belt drives are based on the following guidelines: NEMA Recommendations for Sheave Diameter and Width Average Service at Reducer Rated Load elt Minimum For other conditions (including but not limited to; fire hazard, explosion hazard or choked input), contact Application Engineering (1 800 66 09) for assistance in selecting a belt drive. It is recommended that 50 hp motors and larger the sheave diameters shown be checked with the motor manufacturer to be sure they meet their recommendations for minimum pitch diameter. 6

Accessories Shaft Mount Reducers Preselected elt Drives 15SMTP09 15SMTP09 Variable 15SMTP09 elt Variable ushing ushing elts elts ushing ushing 4 9 6MVP4054 5 4C60Q Q 4C500R CX 6MV80R 6 0 4 6MVP4054 6 45V48 X 5 7 5MV80R 7 45V50 5MVP5569 5 8 54 5MV00R 8 45V5 R 46 5 MVP75C97Q 9 45V54 5 59 MVP85C7Q 0 45V56 MVC60R CX 60 70 MVP5C17Q Q 1 45V58 71 76 MVP115C17Q 45V60 4 4S5V75 77 87 MVP915V5Q MV5V40S 4 45V6 88 95 4MV5V40S S1 5 45V64 4MVP15V115 96 8 4MV5V1S 4 6 45V66 9 11 4MVP1115V15 4MV5V00R 7 8 45V70 S1 1 5MVP915V5 5MV5V180S 9 41 45V74 11 14 5MV5V160S 4 44 45V80 5MVP15V115 144 159 S1 5 45 46 45V86 5MV5V140S 160 177 47 48 5V90 5MVP1115V15 178 00 5MV5V15S 49 51 5V94 5 55 R5V 56 59 R5V9 S5V75 60 6 R5V118 64 67 R5V15 68 71 R5V1 7 7 45V90 74 78 45V94 45V50 79 8 4R5V 8 87 4R5V9 88 9 45V4 4 94 0 4R5V15 45V50 1 6 4R5V1 7 11 45V4 11 115 5R5V9 116 11 55V1 1 19 5R5V118 17 55V14 55V184 5 18 14 5R5V1 14 150 55V16 151 158 55V14 159 16 6S5V1 S1 65V160 164 17 65V16 174 185 65V14 6 186 191 6S5V1 65V16 S1 19 00 65V16 elt Shaft Mount Accessories Notes: Preselected belt drives are based on the following guidelines: NEMA Recommendations for Sheave Diameter and Width Average Service at Reducer Rated Load elt Minimum For other conditions (including but not limited to; fire hazard, explosion hazard or choked input), contact Application Engineering (1 800 66 09) for assistance in selecting a belt drive. It is recommended that 50 hp motors and larger the sheave diameters shown be checked with the motor manufacturer to be sure they meet their recommendations for minimum pitch diameter. 7

Accessories Shaft Mount Reducers Preselected elt Drives 15SMTP15 15SMTP15 Variable 15SMTP15 elt Variable ushing ushing elts ushing 17 5MVP4054 1 55V4 5MV00R 7 5MVP5569 14 55V46 P 8 1 5MVP5064 R X 5 15 5T50 5 5MVP6074 5MV50R 16 5T5 6 41 5MVP7074 17 5T54 4 48 MVP75C97Q 18 45V4 P1 MVC40R 49 55 MVP90C11Q CX 19 4Q5V46 Q 45V78 56 6 MVP85C7Q MVC00R 0 45V46 64 69 MVP915V5Q Q 1 45V48 M5V180R 70 76 45V46 MVP15V115Q 45V50 77 86 MV5V160R 4 5 45V50 87 95 MVP915V5Q MV5V1R 6 45V5 96 4 4MVP15V115 7 8 5V56 4MV5V1R 4 5 114 4MVP1115V15 9 0 5V60 115 5MVP915V5 5MV5V97R R 5 1 5V66 5 5V70 6 7 5V74 8 9 45V64 40 45V66 41 4 45V68 4 45V70 44 46 45V74 47 48 45V80 49 50 4R5V85 51 5 45V86 45V00 54 55 45V90 56 58 45V94 59 4R5V97 60 6 4R5V 6 65 4R5V9 66 67 45V1 68 69 45V90 70 7 45V94 74 78 4R5V 80 8 4R5V9 8 85 45V1 45V160 86 89 4R5V118 90 95 4R5V15 96 0 4R5V1 1 5 4R5V140 6 11 4R5V15 11 118 4R5V1 45V16 119 14 4R5V140 15 4R5V1 45V14 ushing 5T80 Q elts elt 5 5V50 4 4 Notes: Preselected belt drives are based on the following guidelines: NEMA Recommendations for Sheave Diameter and Width Average Service at Reducer Rated Load elt Minimum For other conditions (including but not limited to; fire hazard, explosion hazard or choked input), contact Application Engineering (1 800 66 09) for assistance in selecting a belt drive. It is recommended that 50 hp motors and larger the sheave diameters shown be checked with the motor manufacturer to be sure they meet their recommendations for minimum pitch diameter. 8

Accessories Shaft Mount Reducers Preselected elt Drives 15SMTP5 15SMTP5 Variable 15SMTP5 elt Variable ushing ushing elts ushing MVP549 6 4T4 P 11 1 MVP4054 7 4T8 1 MVP4559 MV00R 8 45V44 P1 14 15 MVP5064 9 45V48 16 17 MVP5569 T6 P X 18 0 4MVP4559 11 K45 1 4MVP5569 1 5V44 P1 4 6 4MVP6074 4MV00R 4 1 5V48 7 9 4MVP7084 14 5V5 0 4MVP8094Q 15 5V56 4 9 MVP75C97Q 16 5V58 40 45 MVP95C117Q MVC180R CX 17 45V4 Q 46 49 MVP5C17Q 18 45V44 P1 50 56 MV5V1R 19 45V48 MVP915V5Q 57 6 0 45V50 MV5V118R 64 70 1 45V5 MVP15V115Q 71 80 MV5VR 45V56 4 45V60 5 45V6 6 45V64 7 45V66 8 45V68 9 0 5V6 1 5V66 5V70 4 5 5V74 6 7 R5V80 8 9 R5V85 40 4 R5V90 4 44 5V94 45 46 5V86 47 48 5V90 49 51 5V94 5 55 R5V 56 59 5V1 60 6 R5V118 64 67 5V14 68 69 R5V1 70 7 5V16 74 77 R5V1 78 80 5V16 ushing 4T80 5V78 elts elt 4 X 45V184 4 5V154 5V16 5V14 Shaft Mount Accessories Notes: Preselected belt drives are based on the following guidelines: NEMA Recommendations for Sheave Diameter and Width Average Service at Reducer Rated Load elt Minimum For other conditions (including but not limited to; fire hazard, explosion hazard or choked input), contact Application Engineering (1 800 66 09) for assistance in selecting a belt drive. It is recommended that 50 hp motors and larger the sheave diameters shown be checked with the motor manufacturer to be sure they meet their recommendations for minimum pitch diameter. 9

Accessories Shaft Mount Reducers Preselected elt Drives 15SMTP5 15SMTP5 Variable 15SMTP5 elt Variable ushing ushing elts ushing 7 8 MVP549 MV00R 5 K 9 MVP549 6 T6 P 11 1 MVP4559 7 5V4 P1 1 14 VP71 5V50 X 8 K55 15 16 MVP7084P P 9 5V54 17 18 MVP8094Q Q T6 P 19 0 V5870 11 5V44 P1 5V184 1 V6880 1 5V48 4 7 MVP85C7Q 1 5V5 TC00 8 0 MVP95C117Q 14 5V56 1 8 MVP75C97Q Q CX 15 5V60 9 4 MVP90C11Q MVQ Q 16 17 5V66 44 50 MVP5C17Q 18 5V5 19 5V56 0 5V58 1 5V6 5V54 4 5 5V58 6 5V6 7 5V64 8 5V66 9 5V68 0 1 5V74 5V86 4 5 5V90 6 5V94 7 R5V9 8 9 R5V 40 41 5V86 4 4 5V90 44 45 5V94 46 48 R5V 49 50 R5V9 ushing T00 5V00 5V154 5V14 5V16 5V1 elts X elt Notes: Preselected belt drives are based on the following guidelines: NEMA Recommendations for Sheave Diameter and Width Average Service at Reducer Rated Load elt Minimum For other conditions (including but not limited to; fire hazard, explosion hazard or choked input), contact Application Engineering (1 800 66 09) for assistance in selecting a belt drive. It is recommended that 50 hp motors and larger the sheave diameters shown be checked with the motor manufacturer to be sure they meet their recommendations for minimum pitch diameter. 1

Accessories Shaft Mount Reducers Preselected elt Drives 407SMTP05 407SMTP05 Variable 407SMTP05 elt Variable ushing ushing elts ushing ushing 11 117 MVP915V5Q MV5V00S 90 9 4R5V97 118 17 4MVP15V115 4MV5V00S 94 98 4R5V 18 151 4MVP1115V15 4MV5V80S 4 99 4R5V9 15 161 4MVP15V115 4M5V140S 7 45V1 4S5V75 S1 16 185 5MVP915V5 8 11 4R5V118 186 0 5MVP15V115 5MV5V00S S1 114 117 4R5V15 5 0 0 118 15 65V86 5MVP1115V15 1 44 5MV5V180S 16 65V90 45 70 6MV5V150S 11 16 65V94 65V50 6MVP15V115 71 0 6M5V1S 6 17 19 6R5V97 0 15 6MVP1115V15 6MV5V140S 140 146 6R5V 147 155 5R5V9 156 159 55V1 160 168 5R5V118 169 178 5R5V15 179 188 5R5V1 189 196 55V16 197 199 5R5V140 00 6R5V9 65V184 11 6S5V15 5 6S5V1 65V00 6 49 6S5V140 50 55 6S5V1 S1 56 61 6S5V140 65V184 6 67 65V16 68 7 6R5V118 7 88 6S5V15 89 00 6S5V1 S1 65V154 01 17 6S5V16 18 7 8S5V140 8S5V150 8 40 8S5V1 41 59 S1 8S5V1 60 81 8 400 8S5V140 8S5V15 elts elt 55V50 5 4 6 6 S1 8 Shaft Mount Accessories Notes: Preselected belt drives are based on the following guidelines: NEMA Recommendations for Sheave Diameter and Width Average Service at Reducer Rated Load elt Minimum For other conditions (including but not limited to; fire hazard, explosion hazard or choked input), contact Application Engineering (1 800 66 09) for assistance in selecting a belt drive. It is recommended that 50 hp motors and larger the sheave diameters shown be checked with the motor manufacturer to be sure they meet their recommendations for minimum pitch diameter. 111

Accessories Shaft Mount Reducers Preselected elt Drives 407SMTP15 407SMTP15 Variable 407SMTP15 elt Variable ushing ushing elts ushing 1 MVP75C97Q 15 4Q5V46 Q 4 7 MVP85C7Q 16 45V46 MVC60R R CX 8 40 MVP95C117Q 17 45V48 41 4 MVP5C17Q 18 45V5 44 48 MVP815V95Q Q 19 45V54 49 55 MVP915V5Q MV5V40S S1 0 45V58 56 60 MVP15V115Q 1 45V60 61 67 MVP915V5Q 45V6 MV5V00R 68 7 MVP15V115Q 45V66 7 80 4MV5V00R 4 5 45V70 81 89 4MVP1115V15 4MV5V180R 4 6 45V56 90 99 4MV5V160R 7 45V58 0 8 5MV5V15S S1 8 45V60 5MVP915V5 9 1 5MV5V9R R 5 9 0 45V64 14 5MVP1115V15 5MV5V118S S1 1 45V66 45V70 4 5 45V74 6 7 45V70 8 9 45V74 40 41 4R5V80 4 45V80 4 4R5V85 44 45 45V86 46 47 45V90 48 45V86 49 51 45V90 5 5 45V94 54 55 4R5V 56 58 4R5V90 59 60 4R5V9 61 6 45V94 6 4R5V97 64 66 4R5V 67 68 4R5V9 69 7 45V1 7 76 4R5V118 77 81 4R5V15 8 85 4R5V1 86 88 4R5V15 89 9 4R5V1 94 99 4R5V140 0 6R5V97 7 6R5V 8 1 6R5V9 111 117 65V1 118 1 6R5V118 14 18 6R5V9 19 6R5V1 ushing 4S5V75 S1 45V78 45V50 45V4 45V00 45V184 65V14 65V1 elts elt 4 6 Notes: Preselected belt drives are based on the following guidelines: NEMA Recommendations for Sheave Diameter and Width Average Service at Reducer Rated Load elt Minimum For other conditions (including but not limited to; fire hazard, explosion hazard or choked input), contact Application Engineering (1 800 66 09) for assistance in selecting a belt drive. It is recommended that 50 hp motors and larger the sheave diameters shown be checked with the motor manufacturer to be sure they meet their recommendations for minimum pitch diameter. 11

Accessories Shaft Mount Reducers Preselected elt Drives 407SMTP5 407SMTP5 Variable 407SMTP5 elt Variable ushing ushing elts elts ushing ushing 9 4MVP4559 4MV80R 7 4T40 P 11 1 4MVP4054 8 45V44 P1 4T80 4 1 16 4MVP5569 4 9 45V50 4MV00R X 17 19 4MVP7084 45V56 0 1 4MVP8094Q 11 5V4 P1 4 MVP75C97Q 1 5V46 5 7 MVP85C7Q C70R 1 5V5 5V78 8 19 CX 14 5V54 MVP95C117Q 0 15 5V58 TC40 4 7 MVP5C17Q 16 5V54 8 40 MVP915V5Q Q 17 5V56 41 44 MVP15V115Q MV5V180R 18 5V60 5V4 45 48 MVP1115V15Q 19 5V64 49 5 MVP915V5Q 0 5V66 5 57 MVP15V115Q MV5V140R 1 45V48 58 6 MVP1115V15Q 45V50 6 68 MVP15V115Q MV5V118R 45V5 69 7 4MV5VR 4 45V54 4MVP15V115 7 80 4MV5V97R 5 6 45V58 45V160 4 7 45V60 8 45V6 9 45V64 0 1 5V80 5V86 4 R5V90 5 7 5V94 8 9 R5V 40 41 R5V9 5V184 4 4 5V1 44 45 R5V118 46 48 5V14 49 R5V1 50 5 R5V118 5 56 5V14 57 R5V16 5V160 58 6 5V16 6 64 R5V15 65 67 R5V1 5V16 68 7 5V16 7 77 5R5V 78 80 5R5V9 55V94 5 elt Shaft Mount Accessories Notes: Preselected belt drives are based on the following guidelines: NEMA Recommendations for Sheave Diameter and Width Average Service at Reducer Rated Load elt Minimum For other conditions (including but not limited to; fire hazard, explosion hazard or choked input), contact Application Engineering (1 800 66 09) for assistance in selecting a belt drive. It is recommended that 50 hp motors and larger the sheave diameters shown be checked with the motor manufacturer to be sure they meet their recommendations for minimum pitch diameter. 11

Accessories Shaft Mount Reducers Preselected elt Drives 415SMTP05 415SMTP05 Variable 415SMTP05 Variable ushing ushing 9 4 5MVP15V115 5MV5V75 U0 5 111 5MVP5C17 5MVC60S S 146 165 6MVP15V115 6MV5V40U U0 elt elts ushing ushing 90 9 5R5V1 5 CX 9 96 55V16 5U5V500 6 97 6R5V9 5 65V1 6 111 6R5V118 U0 11 11 65V14 6U5V75 114 117 6S5V15 S1 118 1 6S5V1 1 19 65V16 11 6S5V140 S1 1 17 6R5V9 18 140 65V1 141 148 6R5V118 6S5V80 S1 149 157 6S5V15 S1 158 165 6S5V1 166 168 65V16 169 176 8S5V15 177 186 8S5V1 8U5V50 187 199 8S5V140 00 08 8S5V15 S1 09 0 8S5V1 8U5V1 1 8S5V140 5 5V150J 6 49 5VJ J 5V1870J J 50 61 5V1400J 6 75 U5V15 76 9 U5V1 U5V160 9 09 U1 U1 U5V150 U5V140 54 U5V140 55 7 U5V1 elts elt 5 6 U1 8 Notes: Preselected belt drives are based on the following guidelines: NEMA Recommendations for Sheave Diameter and Width Average Service at Reducer Rated Load elt Minimum For other conditions (including but not limited to; fire hazard, explosion hazard or choked input), contact Application Engineering (1 800 66 09) for assistance in selecting a belt drive. It is recommended that 50 hp motors and larger the sheave diameters shown be checked with the motor manufacturer to be sure they meet their recommendations for minimum pitch diameter. 114

Accessories Shaft Mount Reducers Preselected elt Drives 415SMTP15 415SMTP15 Variable 415SMTP15 elt Variable ushing ushing elts ushing 4 8 5MVC440U U0 1 4Q5V49 5MVP75C97 9 1 45V5 CX 5 4 8 5VMP85C7 5MVC60S S 14 45V54 9 44 5MVP5C17 15 45V60 45 48 4MVP15V115 16 45V6 4MV5V00S 49 5 S1 4 17 45V66 4MVP1115V15 5 56 4MV5V80S 18 45V70 57 6 5MVP915V5 19 45V74 6 67 5MVP15V115 5MV5V1U U0 5 0 45V80 68 74 5MVP11115V115 1 4R5V85 75 80 6MV5V180S 4R5V86 81 90 6MVP15V115 6MV5V160S S 6 45V90 91 1 6MV5V140S 4 45V94 5 6 45V74 7 4R5V80 8 4R5V85 9 0 4R5V90 1 45V94 4S5V75 4R5V97 4 5 4R5V 6 4R5V9 7 45V1 8 65V86 9 41 6R5V90 6S5V80 4 4 65V94 44 65V86 45 46 65V90 47 48 65V94 49 6R5V97 50 5 6R5V 5 55 6R5V9 56 57 65V1 65V50 58 60 6R5V118 61 64 65V14 65 66 6S5V1 S1 67 65V16 68 71 6S5V140 S1 7 75 6R5V118 76 79 65V14 80 8 6S5V1 S1 65V00 84 86 65V16 87 88 6S5V140 S1 89 9 6R5V118 9 98 6S5V15 65V160 99 1 6S5V1 6 8S5V1 8S5V160 7 11 S1 8S5V140 11 8S5V150 11 18 8S5V1 19 8S5V140 8S5V1 ushing 4U5V500 U0 S1 elts elt 4 6 S1 8 Shaft Mount Accessories Notes: Preselected belt drives are based on the following guidelines: NEMA Recommendations for Sheave Diameter and Width Average Service at Reducer Rated Load elt Minimum For other conditions (including but not limited to; fire hazard, explosion hazard or choked input), contact Application Engineering (1 800 66 09) for assistance in selecting a belt drive. It is recommended that 50 hp motors and larger the sheave diameters shown be checked with the motor manufacturer to be sure they meet their recommendations for minimum pitch diameter. 115

Accessories Shaft Mount Reducers Preselected elt Drives 415SMTP5 415SMTP5 Variable 415SMTP5 elt Variable ushing ushing elts ushing 11 1 5MVP4054 6 5V4 P1 1 14 5MVP5064 5MV00R X 5 7 V50 15 16 5MVP6074 8 5V44 P1 17 19 MVP85C7Q 9 V550 Q MVC60R 0 1 MVP95C117Q R 5V54 4 4MVP75C97Q 11 5V60 CX 5 8 4MVP95C117Q 4MVC70R 1 5V66 Q 9 4MVP115C17Q 4 1 5V70 4 8 4MVP95C117Q 4MVC00R 14 45V50 9 46 4MVP15V115 4MV5V180R 15 45V56 47 51 5MVP915V5 16 45V58 5 56 5MVP15V115 5MV5V140S 17 45V6 57 61 S1 18 45V64 5 6 67 5MV5V15S 19 45V68 5MVP1115V15 68 7 5MV5V118S 0 45V74 7 80 5MV4V9R R 1 5V86 5V90 R5V9 4 R5V97 5 R5V 6 R5V9 7 5V1 8 9 R5V118 0 1 5V14 4R5V90 4 45V90 5 45V94 6 45V97 7 8 4R5V 9 41 55V94 4 5R5V97 4 44 5R5V 45 5R5V9 46 47 55V1 48 50 5R5V118 51 5R5V15 5 54 6R5V97 55 56 6R5V 57 58 6R5V9 59 6 6 66 65V1 67 70 6R5V118 71 74 65V14 75 78 6S5V1 S1 79 80 6S5V140 ushing U5V500 U0 S5V75 S1 45V50 elts elt 5V78 45V184 4 55V160 65V14 6R5V118 4 5 6 Notes: Preselected belt drives are based on the following guidelines: NEMA Recommendations for Sheave Diameter and Width Average Service at Reducer Rated Load elt Minimum For other conditions (including but not limited to; fire hazard, explosion hazard or choked input), contact Application Engineering (1 800 66 09) for assistance in selecting a belt drive. It is recommended that 50 hp motors and larger the sheave diameters shown be checked with the motor manufacturer to be sure they meet their recommendations for minimum pitch diameter. 116

Accessories Shaft Mount Reducers Preselected elt Drives 507SMTP15 507SMTP15 Variable 507SMTP15 elt Variable ushing ushing elts ushing ushing 8 0 5MV5V440U 55V86 5MVP915V5 1 5 4 55V90 5 5U5V500 6 9 5MVP15V115 5MV5V75U 5 55V94 40 4 5MVP1115V15 U0 6 5R5V 44 49 6MV5V00U 7 8 65V80 50 5 6MVP15V115 6MV5V80U 6 9 0 6V5V86 54 61 6M5V40U 1 65V90 U0 6R5V97 4 5 6R5V 6 8 6R5V9 6U5V75 9 41 6R5V118 4 44 65V14 45 46 6S5V1 S1 47 48 65V16 49 51 6R5V9 5 54 6R5V118 6S5V80 S1 55 58 65V1 59 61 6R5V118 65V50 6 65 8S5V15 66 69 8S5V1 8U5V50 70 7 8S5V140 7 77 8S5V15 S1 78 81 8S5V1 8U5V1 8 87 8S5V140 88 9 5VJ 9 97 5V1400J J 5V1870J J 98 U5V15 8 U5V1 U5V160 9 115 U1 U1 116 1 U5V140 U5V150 14 U5V140 elts elt 5 6 U1 8 Shaft Mount Accessories Notes: Preselected belt drives are based on the following guidelines: NEMA Recommendations for Sheave Diameter and Width Average Service at Reducer Rated Load elt Minimum For other conditions (including but not limited to; fire hazard, explosion hazard or choked input), contact Application Engineering (1 800 66 09) for assistance in selecting a belt drive. It is recommended that 50 hp motors and larger the sheave diameters shown be checked with the motor manufacturer to be sure they meet their recommendations for minimum pitch diameter. 117

Accessories Shaft Mount Reducers Preselected elt Drives 507SMTP5 507SMTP5 Variable 507SMTP5 elt Variable ushing ushing elts ushing ushing 1 14 6MVP6074 6MV80R R X 6 7 45V50 15 17 MVP85C7Q 8 45V56 4U5V500 MVC440U U0 CX 18 0 MVP5C17Q Q 9 45V64 U0 1 4 MVP915V5Q MV5V00S 55V5 5 8 4MVP15V115 4 11 55V58 4MV5V80S 9 1 4MVP1115V15 1 55V64 6 5MV5V00S 1 55V68 5MVP915V5 7 40 S1 14 55V74 41 44 5MVP15V115 5MV5V180S 5 15 55V80 5U5V75 45 48 5MVP1115V15 16 5R5V90 49 5 5MVP15V115 5MV5V150S 17 55V90 54 61 5MVP1115V15 5MV5V140S 18 55V94 19 5R5V 0 1 55V1 55V80 5R5V85 4 55V86 5 55V90 6 55V94 7 55V97 55V50 8 5R5V 9 5R5V9 0 1 55V1 5R5V118 4 55V14 5 6 6R5V 7 9 65V1 40 41 6R5V118 4 44 65V14 65V00 45 46 6S5V1 47 49 6S5V140 S1 50 5 6R5V118 54 57 65V14 58 59 6S5V1 65V154 60 61 65V16 6 66 8S5V140 8S5V150 67 71 8S5V1 S1 8S5V1 7 80 8S5V140 8S5V15 elts elt 4 5 6 S1 8 Notes: Preselected belt drives are based on the following guidelines: NEMA Recommendations for Sheave Diameter and Width Average Service at Reducer Rated Load elt Minimum For other conditions (including but not limited to; fire hazard, explosion hazard or choked input), contact Application Engineering (1 800 66 09) for assistance in selecting a belt drive. It is recommended that 50 hp motors and larger the sheave diameters shown be checked with the motor manufacturer to be sure they meet their recommendations for minimum pitch diameter. 118

Accessories Shaft Mount Reducers Preselected elt Drives 608SMTP15 608SMTP15 Variable 608SMTP15 Variable elt ushing ushing elts ushing No Drives Available 0 8R5V80 1 8R5V85 R 8R5V90 4 8S5V97 5 6 8S5V 7 8 8S5V9 8U5V500 9 0 8S5V118 1 8S5V15 4 8S5V1 S1 5 7 8S5V140 8 40 8S5V118 41 4 8S5V15 4 45 8S5V1 8U5V75 46 48 8S5V140 49 51 U5V15 5 54 U5V1 55 57 U5V140 58 60 U5V1 U5V80 61 64 U5V140 U1 65 68 U5V1 U5V50 69 7 U5V140 U5V50 7 75 U5V15 76 80 U5V1 U5V1 81 84 U5V140 ushing U1 5V150M M U1 elts elt 8 Shaft Mount Accessories Notes: Preselected belt drives are based on the following guidelines: NEMA Recommendations for Sheave Diameter and Width Average Service at Reducer Rated Load elt Minimum For other conditions (including but not limited to; fire hazard, explosion hazard or choked input), contact Application Engineering (1 800 66 09) for assistance in selecting a belt drive. It is recommended that 50 hp motors and larger the sheave diameters shown be checked with the motor manufacturer to be sure they meet their recommendations for minimum pitch diameter. 119

Accessories Shaft Mount Reducers Preselected elt Drives 608SMTP5 608SMTP5 Variable 608SMTP5 elt Variable ushing ushing elts elts ushing ushing 1 14 5MVP75C97 9 55V66 5MVC440U CX 15 16 5MVP85C7 5Q5V75 Q 5 17 0 5MV5V75U 11 55V80 5U5V500 5MVP915V5 1 4 5MV5V00U U0 1 55V66 5 8 6MV5V80U 1 55V94 9 6MVP15V115 6MV5V40U 6 14 5R5V80 5 6MV5V1U 15 55V80 16 5R5V90 17 55V90 U0 5 18 5R5V97 19 5R5V 0 55V1 5U5V75 1 5R5V118 5R5V15 4 5R5V1 5 55V16 6 5R5V140 7 65V1 8 9 6R5V118 0 1 65V14 6S5V80 S1 6 6S5V1 4 5 6S5V140 6 7 8S5V1 8U5V50 U1 8 9 8S5V140 40 41 S1 85V60J J 4 4 8S5V1 8 8U5V1 U1 44 46 8S5V140 47 49 8S5V1 50 5 8S5V140 85V1870J J 5 54 U5V15 55 57 U5V1 U5V160 58 6 U5V140 6 66 U5V1 67 70 U5V1 U1 U5V140 U1 71 74 U5V1 75 78 U5V140 U5V15 79 80 S5V118 elt Notes: Preselected belt drives are based on the following guidelines: NEMA Recommendations for Sheave Diameter and Width Average Service at Reducer Rated Load elt Minimum For other conditions (including but not limited to; fire hazard, explosion hazard or choked input), contact Application Engineering (1 800 66 09) for assistance in selecting a belt drive. It is recommended that 50 hp motors and larger the sheave diameters shown be checked with the motor manufacturer to be sure they meet their recommendations for minimum pitch diameter.

Accessories Shaft Mount Reducers Preselected elt Drives 800SMTP5 Variable 800SMTP5 Variable 800SMTP5 elt ushing ushing elts elts ushing ushing No Drives Available 5 9 No Drives Available 85V7SF SF 8U5V500 U1 8 11 6R5V80 1 65V86 1 65V90 14 6R5V 15 6R5V9 5V 6U5V500 U0 16 65V1 6 17 6S5V15 S1 18 65V14 19 65V16 0 6S5V140 1 5S8V1 5S8V140 58V4450N N 5S8V1 4 5 5S8V140 S1 5U8V400 U0 8V 5 6 6S8V1 7 8 6S8V140 68V550N N 6 9 0 8S5V1 1 8S5V140 85V150M M 8 U5V1 U5V80 4 5 U5V140 U1 6 8 U5V1 U1 U5V50 9 40 U5V140 41 4 5V60M M 4 44 8S8V140 S 8U8V4 8 45 47 U8V1 U1 8V U8V140 U1 48 50 U8V00 51 80 No Drives Available elt Shaft Mount Accessories Notes: Preselected belt drives are based on the following guidelines: NEMA Recommendations for Sheave Diameter and Width Average Service at Reducer Rated Load elt Minimum For other conditions (including but not limited to; fire hazard, explosion hazard or choked input), contact Application Engineering (1 800 66 09) for assistance in selecting a belt drive. It is recommended that 50 hp motors and larger the sheave diameters shown be checked with the motor manufacturer to be sure they meet their recommendations for minimum pitch diameter. 11

elt guard assemblies consist of a guard kit and a mounting bracket kit as shown in the tables. Mounting bracket kit must be purchased separately. These belt guards may also be used with screw conveyor drives. elt guard standard color is yellow. rackets supplied can accommodate fan kits when required. Plated fasteners providing protection in outdoor applications are supplied with the guard assembly. elt guards have a hinged, removable cover. Accessories Shaft Mount Reducers elt Guard elt guards may be assembled with the belt drive already installed. C C Max./Min. CD Max./Min. CD D D E Sheave Dia. A E Sheave Dia. A Dimensions in Inches Top Mount elt Guard Center distance E A C D Kit No. Min. Max. Max. GP 1.00 0.00 11.00 1.50 6.50 5.50.00 GP14 180 18.00 0.00 15.00 45.50 6.50 7.50 14.00 GP0 4.00 4.00 1.00 55.50 6.50.50 0.00 GP4 48 4.00 8.00 5.00 6.50 8.50 1.50 4.00 GP8 48.00 48.00 9.00 77.50 8.50 14.50 8.00 GP 467 4.00 6.00.00 95.50 8.50 16.50.00 Top Mount Mounting racket Kit No. Side Mount Reducer Side Mount Mounting racket Kit No. Reducer 7GMKPT 7 7GMKPS 7 115GMKPT 115 115GMKPS 115 0GMKPT 0 0GMKPS 0 07GMKPT 07 07GMKPS 07 15GMKPT 15 15GMKPS 15 07GMKPT 07 07GMKPS 07 15GMKPT 15 15GMKPS 15 407GMKPT 407 415GMKPT 415 507GMKPT 507 608GMKPT 608 800GMKPT 800 1

Accessories Shaft Mount Reducers ushing Guard ushing guard kits have the following features: One kit will cover the bushing and end cap Kit may be used with bushing on the front or rear of the reducer housing Guard may be installed after the reducer and bushing are mounted to the equipment Guard has the ability to mount on several different shaft sizes Shaft Mount Accessories A Typ. Typ. Reducer ushing Guard Kit ushing Guard Kit when used with optional Fan Kit A 7 7 ushing Guard Kit NA.44.88 115 115 ushing Guard Kit NA.51 4.74 0 0 ushing Guard Kit NA.6 5.1 07 07 ushing Guard Kit NA.75 5.50 15 15 ushing Guard Kit NA.19 5.9 07 07 ushing Guard Kit 07 ushing Guard Fan Kit.00 7. 15 15 ushing Guard Kit 15 ushing Guard Fan Kit.0 7.81 407 407 ushing Guard Kit 407 ushing Guard Fan Kit.50 8.75 415 415 ushing Guard Kit 415 ushing Guard Fan Kit.75.5 507 507 ushing Guard Kit 507 ushing Guard Fan Kit.15 11.00 608 608 ushing Guard Kit 608 ushing Guard Fan Kit.69 1.50 800 NA NA NA NA 1

Accessories Shaft Mount Reducers SMTP Screw Conveyor Drives E E/ G M L 4 Tapped oles and Slots for F Dia. Trough End Fasteners P J Dia. oles E/ E U D Key K U1 C A Trough End N G U K Optional ole Shaft ASIC UNIT SIZE DIMENSIONS IN INCES A C D L M N P U1 7SMTP 9.76 1.07 1.18.77 1.7 6.90 4.08 1.61 0.75.188 x.188 x.88 115SMTP 11.00 14.08 1.5 4.6 14.5 7.14 4.4 1.7 1.1.50 x.50 x.75 0SMTP 1.88 16.16 1.48 5.6 16.44 7.60 5.1 1.7 1.5.50 x.50 x.88 07SMTP 14.50 18.47 1.6 6.08 17.5 8.51 5.1 1.80 1.44.75 x.75 x.75 15SMTP 16.5 0.88.1 7.01 19.7 9.5 5.87 1.9 1.88.500 x.500 x.75 07SMTP 19.04 4.7.5 7.78.0.94 7.45.5.00.500 x.500 x 6.50 15SMTP 19.90 6.5.6 8.5 5.14 11.56 8..90.1.500 x.500 x 7.50 407SMTP 1.69 7.80.1 9.4.89 1.06 6.70.58.1.500 x.500 x 6.00 KEY 14 DRIVE SAFT DIA. "U" FOR SCREW DIA. DIMENSIONS IN INCES E F G G J K 1.50 6,9 4.00 0.50 6.00 9.00.00 6.00 0.5.1.00 91 5.1 0.6 6.00 9.00.00 6.00 0.66.1.44 1,14 5.6 0.6 6.69 9.69.00 6.00 0.66.75.00 6.00 0.75 6.88 9.88.00 6.00 0.78.88.44 184 6.75 0.75 9.1 1.1 4.00 8.00 0.91.88

Accessories Shaft Mount Reducers SMTP Screw Conveyor Drives STOCK SMTP REDUCER (1) TYPE SMTP SCREW CONVEYOR ADAPTER TYPE SMTP SCREW CONVEYOR SAFT () 1 1/" DRIVE SAFT FOR SCREW DIAMETERS 6 " SMTP screw conveyor drives may be assembled in the field. Required components include: SMTP reducer SMTP screw conveyor adapter SMTP screw conveyor shaft OPTIONAL SEAL CARTRIDGES WASTE PACK KIT PACKING GLAND KIT FELT SEAL () " DRIVE SAFT FOR SCREW DIAMETERS 9 1" 7/16" DRIVE SAFT FOR SCREW DIAMETERS 1 and 14" " DRIVE SAFT FOR SCREW DIAMETERS 1 0" 7/16" DRIVE SAFT FOR SCREW DIAMETERS 18 4" 7SMTP 7SCAP 7DSP8 7WPP 7PGP FR00 115SMTP 115SCAP 115DSP8 1150WPP 1150PGP FR 0SMTP 0SCAP 0DSP8 7SMTP 7SCAP 7DSP00 7WPP 7PGP FR00 115SMTP 115SCAP 115DSP00 0SMTP 0SCAP 0DSP00 1150WPP 1150PGP FR 07SMTP 07SCAP 07DSP00 15SMTP 15SCAP 15DSP00 07407WPP 07407PGP FR08 7SMTP 7SCAP 7DSP07 7WPP 7PGP FR00 115SMTP 115SCAP 115DSP07 0SMTP 0SCAP 0DSP07 1150WPP 1150PGP FR 07SMTP 07SCAP 07DSP07 15SMTP 15SCAP 15DSP07 07407WPP 07407PGP FR08 7SMTP 7SCAP 7DSP00 7WPP 7PGP FR00 115SMTP 115SCAP 115DSP00 0SMTP 0SCAP 0DSP00 1150WPP 1150PGP FR 07SMTP 07SCAP 07DSP00 15SMTP 15SCAP 15DSP00 07407WPP 07407PGP FR08 07SMTP 07SCAP 07DSP00 15SMTP 15SCAP 15DSP00 07407WPP 07407PGP FR08 407SMTP 407SCAP 407DSP00 07SMTP 07SCAP 07DSP07 15SMTP 15SCAP 15DSP07 07407WPP 07407PGP FR08 07SMTP 07SCAP 07DSP07 15SMTP 15SCAP 15DSP07 07407WPP 07407PGP FR08 407SMTP 407SCAP 407DSP07 Shaft stress based on transmitted load must always be checked. Calculations must account for drilled holes on shaft. Shaft Mount Accessories Optional components include: Waste pack Packing gland Felt seal (1) Complete part number by adding ratio, ie: 05, 09, 15, 5 or 5 () Complete part number by adding shaft type Standard hole steel shaft = leave blank (example 7DSP8) Optional hole steel shaft = (example 7DSP8) hole stainless steel shaft = SS (example 7DSP8SS) hole stainless steel shaft = SS (example 7DSP8SS) () Felt seal can be added to the waste pack or packing gland seal cartridge. Screw Conveyor Adapter Kit Felt Seal Waste Pack Kit Packing Gland Kit Screw Conveyor Drive Shaft Kit 15

Accessories Shaft Mount Reducers MTP Screw Conveyor Drives E/ E G M L 4 Tapped oles and Slots for F Dia. Trough End Fasteners P J Dia. oles E/ E U D K C A G U Optional ole Shaft K Trough End For dimensions on hydraulic motor mounting styles, see the table on page 47 ASIC UNIT SIZE Trough End L Standard ole Shaft DIMENSIONS IN INCES 7MTP 6 SAEA 1.7.08 7MTP 9T SAEA 1.7.08 7MTP 1T SAE 1.1.56 115MTP 6 SAEA 1.19.08 115MTP 9T SAEA 1.19.08 115MTP 1T SAE 1.67.56 0MTP 6 SAEA 14.71.58 0MTP 9T SAEA 14.71.58 0MTP 1T SAE 14.90.77 0MTP 14T SAEC4 15.1 4.08 07MTP 6 SAEA 15.75.5 07MTP 1T SAE 15.94.71 07MTP 14T SAEC4 16.5 4.0 15MTP 6 SAEA 17.11.7 15MTP 1T SAE 17..71 15MTP 14T SAEC4 17.66 4.7 07MTP 6 SAEA 19..65 07MTP 14T SAEC4 19.78 4.0 15MTP 6 SAEA 0.47.65 15MTP 14T SAEC4 1.0 4.0 N N 16 ASIC UNIT SIZE DIMENSIONS IN INCES A C D M P 7MTP 9.76 1.07 1.18.77 6.90 1.61 115MTP 11.00 14.08 1.5 4.6 7.14 1.7 0MTP 1.88 16.16 1.48 5.6 7.60 1.7 07MTP 14.50 18.47 1.6 6.08 8.51 1.80 15MTP 16.5 0.88.1 7.01 9.5 1.9 07MTP 19.04 4.7.5 7.78.94.5 15MTP 19.90 6.5.6 8.5 11.56.90 DRIVE SAFT DIA. U FOR SCREW DIA. DIMENSIONS IN INCES E F G G J K 1.50 6,9 4.00 0.50 6.00 9.00.00 6.00 0.5.1.00 91 5.1 0.6 6.00 9.00.00 6.00 0.66.1.44 1,14 5.6 0.6 6.69 9.69.00 6.00 0.66.75.00 6.00 0.75 6.88 9.88.00 6.00 0.78.88.44 184 6.75 0.75 9.1 1.1 4.00 8.00 0.91.88

Accessories Shaft Mount Reducers MTP Screw Conveyor Drives STOCK MTP REDUCER (1) TYPE SMTP SCREW CONVEYOR ADAPTER TYPE SMTP SCREW CONVEYOR SAFT () 1 1/" DRIVE SAFT FOR SCREW DIAMETERS 6 " OPTIONAL SEAL CARTRIDGES WASTE PACK KIT PACKING GLAND KIT FELT SEAL () " DRIVE SAFT FOR SCREW DIAMETERS 9 1" 7/16" DRIVE SAFT FOR SCREW DIAMETERS 1 and 14" " DRIVE SAFT FOR SCREW DIAMETERS 1 0" 7/16" DRIVE SAFT FOR SCREW DIAMETERS 18 4" 7MTP 7SCAP 7DSP8 7WPP 7PGP FR00 115MTP 115SCAP 115DSP8 1150WPP 1150PGP FR 0MTP 0SCAP 0DSP8 7MTP 7SCAP 7DSP00 7WPP 7PGP FR00 115MTP 115SCAP 115DSP00 0MTP 0SCAP 0DSP00 1150WPP 1150PGP FR 07MTP 07SCAP 07DSP00 15MTP 15SCAP 15DSP00 07407WPP 07407PGP FR08 7MTP 7SCAP 7DSP07 7WPP 7PGP FR00 115MTP 115SCAP 115DSP07 0MTP 0SCAP 0DSP07 1150WPP 1150PGP FR 07MTP 07SCAP 07DSP07 15MTP 15SCAP 15DSP07 07407WPP 07407PGP FR08 7MTP 7SCAP 7DSP00 7WPP 7PGP FR00 115MTP 115SCAP 115DSP00 0MTP 0SCAP 0DSP00 1150WPP 1150PGP FR 07MTP 07SCAP 07DSP00 15MTP 15SCAP 15DSP00 07407WPP 07407PGP FR08 07MTP 07SCAP 07DSP00 15MTP 15SCAP 15DSP00 07407WPP 07407PGP FR08 07MTP 07SCAP 07DSP07 15MTP 15SCAP 15DSP07 07MTP 07SCAP 07DSP07 15MTP 15SCAP 15DSP07 07407WPP 07407PGP FR08 07407WPP 07407PGP FR08 Shaft stress based on transmitted load must always be checked. Calculations must account for drilled holes on shaft. Shaft Mount Accessories MTP screw conveyor drives may be assembled in the field. Required components include: MTP reducer SMTP screw conveyor adapter SMTP screw conveyor shaft Optional components include: Waste pack Packing gland Felt seal (1) Complete part number by adding ratio, ie: 05, 09, 15, 5 or 5 () Complete part number by adding shaft type Standard hole steel shaft = leave blank (example 7DSP8) hole steel shaft = (example 7DSP8) Optional hole stainless steel shaft = SS (example 7DSP8SS) hole stainless steel shaft = SS (example 7DSP8SS) () Felt seal can be added to the waste or packing gland pack seal cartridge. Screw Conveyor Adapter Kit Felt Seal Waste Pack Kit Packing Gland Kit Screw Conveyor Drive Shaft Kit 17

Accessories Shaft Mount Reducers CMTP Screw Conveyor Drives E E/ G M L 4 Tapped oles and Slots for F Dia. Trough End Fasteners P D J Dia. oles E/ E U K U C A G K Trough End Optional ole Shaft Trough End Standard ole Shaft N PART NO. DIMENSIONS IN INCES L N 7CMTP Q56 1.97. 7CMTP 40 1.97. 115CMTP Q56 1.4. 115CMTP 40 1.4. 115CMTP 80 15.7 5.61 0CMTP Q56 14.95.8 0CMTP 40 14.95.8 0CMTP 80 16.7 5.61 0CMTP Q 16.7 5.61 07CMTP Q56 16.00.76 07CMTP 40 16.00.76 07CMTP 80 17.77 5.55 07CMTP Q 17.77 5.55 15CMTP Q56 17..8 15CMTP 40 17..8 15CMTP 80 19.5 5.86 15CMTP Q 19.5 5.86 15CMTP Q50 19.5 5.86 07CMTP Q56 19.4.76 07CMTP 40 19.4.76 07CMTP 80 1.7 5.79 07CMTP Q 1.7 5.79 07CMTP Q50 1.7 5.79 15CMTP Q56 0.58.76 15CMTP 40 0.58.76 15CMTP 80.61 5.79 15CMTP Q.61 5.79 15CMTP Q50.61 5.79 18 ASIC UNIT SIZE DIMENSIONS IN INCES A C D M P 7CMTP 9.76 1.07 1.18.77 6.90 1.61 115CMTP 11.00 14.08 1.5 4.6 7.14 1.7 0CMTP 1.88 16.16 1.48 5.6 7.60 1.7 07CMTP 14.50 18.47 1.6 6.08 8.51 1.80 15CMTP 16.5 0.88.1 7.01 9.5 1.9 07CMTP 19.04 4.7.5 7.78.94.5 15CMTP 19.90 6.5.6 8.5 11.56.90 DRIVE SAFT DIA. U FOR SCREW DIA. DIMENSIONS IN INCES E F G G J K 1.50 6,9 4.00 0.50 6.00 9.00.00 6.00 0.5.1.00 91 5.1 0.6 6.00 9.00.00 6.00 0.66.1.44 1,14 5.6 0.6 6.69 9.69.00 6.00 0.66.75.00 6.00 0.75 6.88 9.88.00 6.00 0.78.88.44 184 6.75 0.75 9.1 1.1 4.00 8.00 0.91.88

Accessories Shaft Mount Reducers CMTP Screw Conveyor Drives STOCK CMTP REDUCER (1) TYPE SMTP SCREW CONVEYOR ADAPTER TYPE SMTP SCREW CONVEYOR SAFT () 1 1/" DRIVE SAFT FOR SCREW DIAMETERS 6 " OPTIONAL SEAL CARTRIDGES WASTE PACK KIT PACKING GLAND KIT FELT SEAL () " DRIVE SAFT FOR SCREW DIAMETERS 9 1" 7/16" DRIVE SAFT FOR SCREW DIAMETERS 1 and 14" " DRIVE SAFT FOR SCREW DIAMETERS 1 0" 7/16" DRIVE SAFT FOR SCREW DIAMETERS 18 4" 7CMTP 7SCAP 7DSP8 7WPP 7PGP FR00 115CMTP 115SCAP 115DSP8 1150WPP 1150PGP FR 0CMTP 0SCAP 0DSP8 7CMTP 7SCAP 7DSP00 7WPP 7PGP FR00 115CMTP 115SCAP 115DSP00 0CMTP 0SCAP 0DSP00 1150WPP 1150PGP FR 07CMTP 07SCAP 07DSP00 15CMTP 15SCAP 15DSP00 07407WPP 07407PGP FR08 7CMTP 7SCAP 7DSP07 7WPP 7PGP FR00 115CMTP 115SCAP 115DSP07 0CMTP 0SCAP 0DSP07 1150WPP 1150PGP FR 07CMTP 07SCAP 07DSP07 15CMTP 15SCAP 15DSP07 07407WPP 07407PGP FR08 7CMTP 7SCAP 7DSP00 7WPP 7PGP FR00 115CMTP 115SCAP 115DSP00 0CMTP 0SCAP 0DSP00 1150WPP 1150PGP FR 07CMTP 07SCAP 07DSP00 15CMTP 15SCAP 15DSP00 07407WPP 07407PGP FR08 07CMTP 07SCAP 07DSP00 15CMTP 15SCAP 15DSP00 07407WPP 07407PGP FR08 07CMTP 07SCAP 07DSP07 15CMTP 15SCAP 15DSP07 07CMTP 07SCAP 07DSP07 15CMTP 15SCAP 15DSP07 07407WPP 07407PGP FR08 07407WPP 07407PGP FR08 Shaft stress based on transmitted load must always be checked. Calculations must account for drilled holes on shaft. Shaft Mount Accessories CMTP screw conveyor drives may be assembled in the field. Required components include: CMTP reducer SMTP screw conveyor adapter SMTP screw conveyor shaft Optional components include: Waste pack Packing gland Felt seal (1) Complete part number by adding ratio, ie: 05, 09, 15, 5 or 5 () Complete part number by adding shaft type Standard hole steel shaft = leave blank (example 7DSP8) hole steel shaft = (example 7DSP8) Optional hole stainless steel shaft = SS (example 7DSP8SS) hole stainless steel shaft = SS (example 7DSP8SS) () Felt seal can be added to the waste pack or packing gland seal cartridge. Screw Conveyor Adapter Kit Felt Seal Waste Pack Kit Packing Gland Kit Screw Conveyor Drive Shaft Kit 19

Accessories Shaft Mount Reducers Screw Conveyor Trough Ends s 7407 Formed ot Roll Plate Steel Specifications P art No. SCTE06 x 1 1/" SCTE09 x 1 1/ SCTE09 x SCTE x 1 1/ SCTE x SCTE1 x SCTE1 x 7/16 SCTE1 x SCTE14 x 7/16 SCTE14 x SCTE16 x SCTE18 x SCTE18 x 7/16 SCTE0 x SCTE0 x 7/16 SCTE4 x 7/16 Conveyor Screw Dia. 6" 9 9 1 1 14 14 1 16 18 0 4 Drive S haft Fig D ia.. 1 1 1/" 1 1/ 1 1/ 7/16 7/16 7/16 7/16 7/16 4 Type 6ole 8ole 8ole 8ole 8ole 8ole 8ole 8ole 8ole 8ole 8ole ole ole ole ole 1ole Dimensions A C D E F G J K L 1/8" 4 1/" 1 1/" 1 /4" 1" 9 /4" 4 7/8" 1 /4" 9/16" " 8 1/8" 14 6 1/8 1 5/8 5/8 1 1/ 1 /4 6 7/8 1 /4 9/16 9 /8 1 6 1/8 1 5/8 5/8 1 1/ 1 /4 6 7/8 1/4 11/16 9/16 9 /8 15 1/ 4 6 /8 /8 7/8 1 /4 14 /4 7 /8 1 / 4 9/16 9 1/ 15 1/4 6 /8 7/8 7/8 1 /4 14 /4 7 /8 1/ 4 11/16 9/16 9 1/ 17 /8 7 /4 /4 1 5/8 17 1/4 8 5/8 1/4 11/16 9/16 1 1/4 17 /8 7 /4 /4 1 5/8 17 1/4 8 5/8 11/16 11/16 1/16 1 1/4 17 /8 7 /4 /4 1 5/8 17 1/4 8 5/8 1/4 1/16 1 1/4 0 1/8 9 1/4 7/8 1 5/8 19 1/4 9 5/8 11/16 11/16 1/16 1 1/ 0 1/8 9 1/4 7/8 1 5/8 19 1/4 9 5/8 1/4 1/16 1 1/ 5/8 5/8 1/ 1/4 1 1/4 5/8 1/4 1/16 14 7/8 5 1/ 1 1/8 1/ 1/4 4 1/4 1 1/8 1/4 1/16 16 5 1/ 1 1/8 1/ 1/4 4 1/4 1 1/8 11/16 1/16 /8 1 8 1/ 1 1/ 1/ /4 1/4 6 1/4 1 1/8 1/4 1/16 19 1/ 4 8 1/ 1 1/ 1/ /4 1/4 6 1/4 1 1/8 11/16 1/16 /8 19 1/4 4 5/8 16 1/ 1/ 4 1/8 1/ 0 1/4 15 1/8 11/16 1/16 /8 0 Part No. SCTE06 x 1 1/" SCTE09 x 1 1/ SCTE09 x SCTE x 1 1/ SCTE x SCTE1 x SCTE1 x 7/16 SCTE1 x SCTE14 x 7/16 SCTE14 x SCTE16 x SCTE18 x SCTE18 x 7/16 SCTE0 x SCTE0 x 7/16 SCTE4 x 7/16 D imensions Wt. M N P Q R S T U V W X Y Z A Lbs. 4 1/16" 4 7/16" 15/" 5/8" 15/16" 1/" /16" 7/16" 4 5/64" 7/16" 6.7 4 11/16 6 1/4 4 15/16 1/16 1/64 5 45/64 1/ 4 7/16 5 /64 9/16" 9/16 17. 8 4 11/16 6 1/4 4 15/16 1/16 1/64 5 45/64 1/ 4 7/16 5 /64 9/16 9/16 17. 7 4 /4 6 5/8 4 1/8 5/8 /8 6 1/8 1/ 4 7/16 5 45/64 17/ 9/16 0. 6 4 /4 6 5/8 4 1/8 5/ 8 /8 6 1/8 1/ 4 7/16 5 45/64 17/ 9/16 0. 5 6 1/8 7 15/16 6 1/4 15/16 4 7/64 6 59/64 5/16 9/16 6 51/64 7/8 11/16.8 6 1/8 7 15/16 6 1/4 15/16 4 7/64 6 59/64 5/16 9/16 6 51/64 7/8 11/16. 5 6 1/8 7 15/16 6 1/4 15/16 4 7/64 6 59/64 5/16 9/16 6 51/64 7/8 11/16. 6 /4 8 15/16 6 / 1 / 4 11/16 8 7/64 5/16 9/16 7 9/64 11/16 4. 4 6 /4 8 15/16 6 / 1 / 4 11/16 8 7/64 5/16 9/16 7 9/64 11/16 4. 7 7/16 8 1 5/8 4 57/64 9 17/64 5/16 11/16 8 / /4 11/16 51.1 8 111 9 1/ 9/16 5/64 7 7/64 5/16 11/16 19/ 47/64 7 6/64" 15/16" 11/16 67. 9 8 1 9 1/ 9/16 5/64 7 7/64 5/16 11/16 19/ 47/64 7 6/64 15/16 11/16 67. 7 9 5/8 1 /16 / 4 15/ 1/64 8 /16 / 8 11/16 11 / 11 6/64 9 1/ 11/ 1/16 96. 9 9 5/8 1 /16 / 4 15/ 1/64 8 /16 / 8 11/16 11 / 11 6/64 9 1/ 11/ 1/16 96. 7 14 1/4 1 / 7 19/ 1/ 5 /64 / 8 11/16 7/8 1 55/64 1 1/8 9 7/ 1/16 5/16" 1. 0 Notes: rowning trough ends are drilled to fit CEMA Standard Troughs. The center holes are drilled to fit rowning screw conveyor drives. Z holes in bottom flange only; no holes in top flange.

Accessories Shaft Mount Reducers Options and Accessories s 7800 Shaft Mount Accessories 7800 ackstop Kits REDUCER SIZE PART NO. USE ACKSTOP KIT RATIOS D L D IMENSIONS WT. 7 7SP.000 4.6. 4 115.48 4.57. 1 1150SP 0.48 5.0. 1 07 07SP 4.750 5.695 7. 4 15 5.000 6.0 8. 4 1507SP 07 5.000 6.770 8. 4 ALL 15 15SP 6.000 7.780 16. 407 407SP 6.15 6.65. 0 415 415SP 6.815 7.500 1. 0 507 507SP 7.65 7.969 15. 0 608 608SP 8.75 9.500 17. 0 800 800SP 9.80 1.90 60. 0 LS. Arm Kits R EDUCER SIZE PART NO. 7 7TAP 115 115TAP 0 0TAP 07 07TAP 15 15TAP 07 07TAP 15 15TAP 407 407TAP 415 415TAP 507 507TAP 608 608TAP 800 800TAP 11

Accessories Shaft Mount Reducers Options and Accessories s 7800 Fan Kits D L Reducer 07 15 407 415 507 608 800 Fan Kit No. 07FKP 15FKP 407FKP 415FKP 507FKP 608FKP 800FKP D 9.5.4 1.66 14.8 16.41 16.41 16.41 D imensions Wt. L Lbs. 4.9 5.7 4.56 6.9 6.56 6.69 9.9 4.5 4.9 6.4 8. 1. 1. 1. 1

Accessories Shaft Mount Reducers Options and Accessories s 7800 7800 SMTP VK Vertical reather Kit When a shaft mount speed reducer is mounted with the shaft vertical, a vertical breather kit is needed. Shaft Mount Accessories reather Kit reather Kit Oil Level Oil Level Drain Drain 7800 SMTP FK Filtered reather Kit A filtered breather is recommended in applications where abrasive particles may contaminate the gearbox lubricant. 07800 SMTP PC Pump and Cooler Kit The pump and cooler kit is required for specific operating conditions noted in the Class I, II, and III selection tables. 1

Shaft Mount Engineering Section Shaft Overhung Load Capacity... 16 17 Thrust and Overhung Loads... 18 141 Minimum Shaft Requirements... 14 Face Mounting... 144 145 Lubrication... 146 149 Shaft Mount Engineering 15

SMTP Shaft Overhung Load Capacity (Lbs.) Unit 7608 RPM 7 115 0 07 90 54 44 967 95 0 1 140 54 54 54 54 54 40 40 4 400 95 98 917 89 877 858 5:1 Ratio Reducers Reducer 1 07 15 407 415 199 1 185 114 18 5 7 777 760 740 75 7 1941 1890 1844 1804 1768 077 07 1976 196 1896 154 14 1194 1174 1148 111 88 67 45 7 151 11 1191 1171 1146 150 160 170 180 190 00 0 0 40 54 54 54 54 54 54 54 54 54 54 85 80 75 70 65 60 55 50 47 4 84 88 818 80 79 78 77 76 758 748 700 688 675 668 658 648 68 6 6 618 17 170 1676 1650 165 1604 1580 1559 154 154 1861 186 1795 1770 1745 170 1699 1675 1654 169 119 18 9 78 6 5 18 18 998 1 995 980 965 954 944 95 94 914 904 116 16 91 76 61 51 1 16 16 996 50 60 70 80 90 00 0 0 40 50 60 70 80 90 00 54 54 54 54 54 54 54 54 54 54 54 54 54 54 54 5 40 5 0 7 17 17 1 1 07 07 05 0 0 78 7 7 718 71 708 698 69 688 68 678 67 668 668 66 5 61 605 600 59 588 58 578 575 570 565 560 555 555 550 545 4 1508 149 1477 146 1447 146 14 1411 196 186 176 165 155 145 15 1619 1604 1589 1569 1554 1544 159 1514 1504 1494 1479 1468 1458 1448 148 4 4 4 6 8 5 0 1 9 1 8 8 6 8 5 988 98 97 958 958 948 9 9 9 918 916 901 906 896 891 8 894 889 879 869 868 859 849 848 88 8 88 8 818 814 808 0 986 981 971 956 956 946 91 91 91 916 915 900 905 895 890 88 RPM 0 0 40 50 60 70 80 90 0 1 140 9:1 Ratio Reducers Reducer 7 115 0 07 15 07 15 54 54 54 54 54 54 54 54 54 54 54 54 54 54 99 99 99 99 99 99 99 989 967 950 91 896 86 86 11 11 11 11 11 11 11 11 11 11 11 11 11 11 1717 1717 1717 1717 168 167 1496 17 165 117 1161 116 1116 94 17 17 17 11 01 88 695 577 476 85 09 4 181 15 555 555 545 077 655 4 054 18 168 1497 1578 154 1508 148 4004 4004 856 165 656 64 1941 1670 1716 1675 165 1600 1574 1544 OL = TKP D Overhung Loads Where: OL = Overhung load (pounds) T = Actual shaft torque (inchpounds) D = P.D. of sprocket, sheave, pulley or gear K = 1.0 for chain drives 1.5 for gear drives 1.5 for gearbelt drives 1.50 for Vbelt drives P = Load position factor Note: overhung loads shown are with center of load at one input shaft diameter from seal. For loads located at other distances, use input load position factor. 16 150 160 170 180 190 00 54 54 54 54 54 5 808 78 761 79 71 0 11 11 11 11 11 1 74 59 44 9 14 00 074 09 1987 1951 1911 88 1458 147 141 197 177 6 1519 1498 1474 1456 148 14 4 7 1 1 1 1 1 0 1 1

RPM 0 0 40 50 SMTP Shaft Overhung Load Capacity (Lbs.) Unit 7608 15:1 Ratio Reducers Reducer 7 115 0 07 15 07 15 407 415 507 608 54 54 54 54 54 99 99 99 99 99 11 11 11 11 11 1717 1717 1717 1641 1551 17 17 094 85 649 555 55 58 866 495 4004 4004 95 775 499 447 446 860 484 040 5505 5505 5498 517 480 679 6601 487 401 404 7040 5009 754 545 480 60 70 80 90 0 1 54 54 54 54 54 54 54 54 965 98 891 848 811 778 748 71 11 11 11 11 11 11 11 11 1456 179 117 164 1 1141 118 11 49 65 6 176 0 0 1977 191 04 196 1758 1587 159 155 1517 1487 55 976 74 70 649 586 51 480 877 747 69 548 468 400 8 80 457 467 4196 4050 94 814 716 65 809 68 49 7 67 177 096 01 45 80 40 05 75 50 5 05 Shaft Mount Engineering RPM 0 0 40 5:1 Ratio Reducers Reducer 7 115 0 07 15 07 15 407 415 507 608 800 54 54 54 54 99 99 99 955 11 11 11 11 1717 1716 1598 1451 17 08 695 45 555 458 07 60 4004 90 585 59 447 81 014 5505 590 480 496 6780 594 405 781 7040 557 144 51 860 860 860 860 50 60 70 80 54 54 54 54 91 861 819 784 11 11 11 11 14 159 1195 114 78 145 08 1947 84 01 1787 159 0 7 658 566 794 646 55 45 905 697 51 9 5 45 197 070 44 8 16 011 860 8504 817 789 RPM 0 0 40 50 5:1 Ratio Reducers Reducer 7 115 0 07 15 07 15 54 54 54 54 54 99 99 950 886 84 16 16 16 16 16 1717 16 1441 9 11 168 79 446 7 068 55 1 741 495 15 4004 71 48 951 76 Reducer Load Position Factors (P) Distance in inches from face of the housing 1/ 1 1 1/ 1/ 1/ 4 4 1/ 5 5 1/ 6 6 1/ 7 7 1/ 8 8 1/ 9 9 1/ 7 1.00 1.1 1.6 1.60 1.84.08..55 115 1.00 1.00 1.16 1.6 1.55 1.75 1.95.15 0 1.00 1.00 1.09 1.7 1.44 1.6 1.79 1.97.15. 07 1.00 1.00 1.0 1.19 1.6 1.5 1.69 1.85.01.18 15 1.00 1.00 1.00 1.04 1.18 1.1 1.45 1.59 1.7 1.86.1 07 1.00 1.00 1.00 1.00 1.11 1.0 1.1 1.44 1.60 1.80.05.9.85.55 15 1.00 1.00 1.00 1.00 1.06 1.1 1.1 1.1 1.4 1.56 1.7 1.9.18.51.97.6 407 1.00 1.00 1.00 1.0 1.16 1.0 1.44 1.57 1.7 1.86 1.99.11 415 1.00 1.00 1.00 1.00 1.0 1.15 1.7 1.9 1.5 1.64 1.76 1.88.00.1.4.6.47.59 507 1.00 1.00 1.00 1.00 1.08 1.19 1.0 1.41 1.5 1.6 1.7 1.84 1.95.06.17.7.8.49 608 1.00 1.00 1.00 1.00 1.00 1.05 1.14 1. 1.0 1.8 1.47 1.55 1.64 1.7 1.80 1.89 1.97.05.1 800 1.00 1.00 1.00 1.00 1.00 1.00 1.04 1.09 1.14 1.0 1.6 1. 1.40 1.49 1.59 1.70 1.8 1.98.15 Note: overhung loads shown are with center of load at one input shaft diameter from seal. For loads located at other distances, use input load position factor. 17

SMTP, MTP, CMTP Thrust and Overhung Load Capacity (Lbs.) Unit 715 Single Reduction Reducers 7MTP05 OL at Inches from R.P.M. Thrust Machined ousing Surface Load 4 8 1 90 040 975 80 55 0 1980 94 80 55 1 190 908 80 55 1870 87 77 55 180 858 757 55 140 1796 88 7 55 150 177 8 715 55 160 1746 79 698 55 170 1707 778 687 55 180 1669 757 668 55 190 160 747 658 55 00 1608 7 647 55 1585 70 65 55 0 156 707 6 55 0 1540 69 61 50 40 15 680 600 50 50 1505 67 59 515 60 1488 658 58 505 70 1470 65 577 500 80 1455 648 57 495 90 1440 640 565 490 00 145 640 565 490 14 640 565 490 0 1400 640 565 490 0 190 640 565 490 40 180 640 565 490 50 170 640 565 490 60 158 640 565 490 70 145 640 565 490 80 1 640 565 490 90 640 565 490 400 1 640 565 490 115MTP05 OL at Inches from R.P.M. Thrust Machined ousing Surface Load 4 8 1 90 190 8 67 95 0 5 1160 5 890 1 00 11 99 860 95 8 957 80 885 48 97 805 140 818 5 905 785 150 750 998 88 765 160 708 97 858 745 170 66 95 84 70 180 616 97 818 7 190 570 91 807 700 00 58 895 790 685 505 87 77 670 0 47 860 760 660 0 440 850 750 650 40 418 88 7 65 50 95 815 70 65 60 7 8 715 60 70 50 797 70 6 80 78 69 600 90 15 770 680 590 00 98 765 675 585 80 748 66 575 0 65 74 657 570 0 50 70 645 560 40 5 75 640 555 50 0 717 6 550 60 0 71 68 545 70 185 698 617 55 80 168 690 6 50 90 150 685 605 55 400 677 598 50 0MTP05 OL at Inches from R.P.M. Thrust Machined ousing Surface Load 4 8 1 90 60 155 150 1175 0 60 1458 19 115 1 60 1408 147 85 60 16 7 50 560 115 1165 15 140 500 187 118 990 150 440 147 1 960 160 80 11 7 95 170 8 1188 5 915 180 95 116 8 895 190 5 115 05 875 00 18 98 855 00 90 965 840 0 190 7 948 85 0 180 50 90 8 40 170 91 795 50 158 895 780 60 145 00 885 770 70 1 978 867 755 80 965 855 745 90 5 955 845 75 00 090 94 8 75 075 98 8 715 0 060 915 8 705 0 048 90 798 695 40 05 888 787 685 50 0 88 78 680 60 0 870 770 670 70 995 865 765 665 80 980 848 75 655 90 965 84 747 650 400 950 80 75 640 07MTP05 OL at Inches from R.P.M. Thrust Machined ousing Surface Load 4 8 1 90 49 1907 1688 1470 0 49 187 1618 14 1 49 1755 1555 155 49 169 1498 5 49 16 1447 160 140 4818 1580 1400 150 475 155 160 1185 160 46 1490 1150 170 4540 1450 185 1 180 447 141 15 90 190 4405 178 1 65 00 48 147 119 40 470 1 117 0 0 4 188 114 995 0 4195 16 1118 975 40 4158 18 97 955 50 4 80 940 60 4088 1197 58 90 70 4055 1178 4 905 80 40 1160 5 890 90 990 1145 875 00 950 117 99 860 9 15 975 845 0 870 78 95 85 0 80 60 95 8 40 79 4 918 795 50 755 0 900 780 60 718 0 88 765 70 680 980 865 750 80 647 96 848 75 90 61 948 87 75 400 580 90 80 7 15MTP05 OL at Inches from R.P.M. Thrust Machined ousing Surface Load 4 8 1 90 5400 718 41 5 0 5400 615 0 05 1 5400 50 5 1950 588 47 15 1880 5175 50 085 180 140 506 78 0 1765 150 4950 15 1965 1715 160 4865 157 191 1670 170 4780 7 1868 160 180 4695 05 18 1590 190 46 008 178 1555 00 457 196 174 150 455 19 1707 1490 0 4498 1887 167 1460 0 4460 1855 1645 145 40 448 1815 16 1405 50 495 8 50 185 60 46 790 475 160 70 40 758 447 15 80 49 77 418 1 90 455 700 95 090 00 418 67 7 070 4180 650 50 050 0 4147 6 7 00 0 411 597 0 0 40 4080 578 87 1995 50 4047 55 6 1975 60 401 5 47 1960 70 980 515 0 1945 80 947 49 1 190 90 91 475 195 1915 400 880 457 178 1900 Notes: Above thrust and overhung loads are not applicable for combined thrust and overhung loads; refer such applications to Application Engineering (1 800 66 09). Interpolate for loads at other distances from the housing surface. Overhung load must be applied on the same side as the bushing. 18

SMTP, MTP, CMTP Thrust and Overhung Load Capacity (Lbs.) Unit 07415 Single Reduction Reducers 07MTP05 OL at Inches from R.P.M. Thrust Machined ousing Surface Load 4 8 1 90 850 84 41 980 0 8 687 7 860 1 811 58 14 745 7909 41 08 645 7698 95 95 555 140 7487 19 8 475 150 775 09 747 400 160 7064 01 67 5 170 685 97 598 70 180 6641 855 55 15 190 640 78 47 160 00 619 70 415 1 6007 444 94 445 0 5796 48 89 400 0 5585 48 84 55 40 57 467 788 50 516 417 74 70 60 4951 417 70 5 70 479 4118 657 195 80 458 408 6 165 90 417 407 58 00 46 4000 550 0 894 95 508 065 0 68 90 480 040 0 47 880 445 0 40 60 848 417 985 50 049 817 88 960 60 88 785 60 95 70 66 75 9 80 415 7 0 885 90 04 695 80 865 400 199 66 5 840 15MTP05 OL at Inches from R.P.M. Thrust Machined ousing Surface Load 4 8 1 90 7019 549 4887 480 0 697 54 466 4085 1 6844 505 4470 915 674 48 498 765 667 4660 4145 60 140 651 4507 4008 5 150 6414 46 88 400 160 608 47 768 00 170 601 4115 660 05 180 6095 400 56 190 5988 9 475 040 00 5881 8 9 965 5775 78 17 895 0 5668 66 47 80 0 556 597 18 770 40 5455 5 117 7 50 5455 48 0 65 60 5455 7 94 560 70 5455 45 870 495 80 5455 160 795 40 90 5455 075 70 65 00 5455 995 650 05 5455 9 587 50 0 5455 85 5 195 0 5455 788 467 145 40 5455 7 408 095 50 5455 658 5 045 60 5455 600 00 000 70 5455 54 48 1955 80 5455 480 195 19 90 5455 40 150 1870 400 5455 77 180 Shaft Mount Engineering 407SMTP05 OL at Inches from R.P.M. Thrust Machined ousing Surface Load 4 8 1 90 5557 668 5897 5155 0 585 668 5897 5155 1 58 6490 5765 5040 55 60 5615 49 4985 6175 5485 4795 140 490 6040 565 4690 150 4875 5918 557 4595 160 480 580 515 4505 170 4765 5698 506 445 180 47 5600 4975 450 190 4655 55 4895 480 00 4600 548 48 415 4545 55 475 4155 0 4490 57 468 4095 0 445 500 460 4040 40 480 517 456 990 50 45 507 4507 940 60 470 5015 4455 895 70 470 4957 440 850 80 470 4907 458 8 90 470 485 41 770 00 470 480 467 70 470 4758 47 695 0 470 471 4187 660 0 470 4668 4147 65 40 470 468 411 595 50 470 459 4078 565 60 470 455 404 55 70 470 451 4008 505 80 470 4475 975 475 90 470 444 947 450 400 470 441 918 45 R.P.M. 415SMTP05 OL at Inches from Machined ousing Surface Notes: Above thrust and overhung loads are not applicable for combined thrust and overhung loads; refer such applications to Application Engineering (1 800 66 09). Interpolate for loads at other distances from the housing surface. Overhung load must be applied on the same side as the bushing. Thrust Load 4 8 1 90 158 1970 1480 990 0 1479 1400 11970 540 1 175 1895 1150 145 170 145 111 9795 1166 50 765 9480 140 6 11688 44 9195 150 11958 116 15 8940 160 1185 165 9885 8705 170 11749 785 965 8485 180 11645 5 9408 885 190 11541 97 9198 80 00 1147 080 9005 790 11 9877 88 7770 0 118 9678 8647 7615 0 1114 950 8488 7475 40 10 90 85 740 50 915 917 819 715 60 811 9018 8057 7095 70 707 887 797 6980 80 60 878 7807 6875 90 498 860 7687 6770 00 94 8485 7580 6675 90 86 747 6580 0 186 850 770 6490 0 08 814 77 6405 40 9977 804 718 65 50 987 798 709 645 60 9769 784 7007 6170 70 9665 7748 69 6095 80 9560 7658 684 605 90 9456 7568 676 5955 400 95 7487 6688 5890 19

SMTP, MTP, CMTP Thrust and Overhung Load Capacity (Lbs.) Unit 715 Double Reduction Reducers Reducer R.P.M. 0 0 40 50 60 70 80 90 0 1 140 150 160 170 180 190 00 Thrust Load 040 040 040 040 040 00 1890 1780 1670 1590 15 1475 1440 1405 170 148 15 180 6 7MTP09 7MTP15 7MTP5 7MTP5 OL at Inches from Machined ousing Surface 4 8 1 1604 1597 187 15 116 9 988 940 908 87 850 8 805 78 765 75 70 70 0 80 80 80 80 80 80 80 80 80 80 77 750 7 7 69 675 66 645 65 55 55 55 55 55 55 55 55 55 55 55 55 55 55 55 55 55 55 55 5 1 0 7 7 6 5 Reducer R.P.M. 0 0 40 50 60 70 80 90 0 1 140 150 160 170 180 190 00 Thrust Load 190 190 190 190 190 050 9 770 60 55 475 98 0 7 5 178 097 06 0 115MTP09 115MTP15 115MTP5 115MTP5 OL at Inches from Machined ousing Surface 4 8 1 677 17 186 168 1558 1460 18 15 167 118 118 1150 1115 8 57 0 1 99 97 5 1964 1878 164 1487 177 190 1 1170 1118 77 4 15 985 957 9 9 89 877 858 4 9 9 9 190 1195 1 60 15 970 95 905 880 855 80 8 790 775 760 745 7 0 9 8 0 Reducer R.P.M. 0 0 40 50 60 70 80 90 0 1 140 150 160 170 180 190 00 Thrust Load 60 60 60 60 60 45 0 05 840 789 78 687 66 58 517 450 8 17 50 0 0MTP09 0MTP15 0MTP5 0MTP5 OL at Inches from Machined ousing Surface 4 8 1 408 695 8 194 1808 17 164 1570 150 1458 141 168 17 197 165 18 115 1188 16 86 85 06 186 1718 160 15 145 190 145 19 15 11 118 1148 1 97 75 5 0 1884 1884 1795 160 1495 195 15 165 1 1170 115 90 55 0 00 975 955 95 915 89 0 1 1 8 5 Reducer R.P.M. 0 0 40 50 60 70 80 90 0 1 140 150 160 170 180 190 00 Thrust Load 49 49 49 49 49 49 467 445 4198 960 790 60 450 80 5 170 115 060 0 96 07MTP09 07MTP15 07MTP5 07MTP5 OL at Inches from Machined ousing Surface 4 8 1 458 545 05 7 508 8 195 087 1997 191 1840 178 17 1670 165 1588 1548 1508 1477 44 9 140 70 4 07 1945 1848 1768 169 160 1578 157 1480 1440 1407 17 17 8 8 607 607 55 1 195 1805 1695 16 1540 1475 140 175 190 155 15 1195 1165 1140 111 0 1 5 1 0 5 Reducer R.P.M. 0 0 40 50 60 70 80 90 0 1 140 150 160 170 180 190 00 Thrust Load 5400 5400 5400 5400 5055 47 465 400 900 780 660 540 470 400 0 60 198 15 07 01 15MTP09 15MTP15 15MTP5 15MTP5 OL at Inches from Machined ousing Surface 4 8 1 617 479 4 69 9 158 978 8 700 59 49 408 68 0 14 09 048 00 95 54 45 655 77 008 80 64 50 95 98 1 17 068 01 195 190 1857 1817 1777 7 456 7 190 860 65 445 05 185 090 005 190 1865 1805 1755 1705 1660 160 1585 1550 151 0 1 8 1 7 5 Notes: Above thrust and overhung loads are not applicable for combined thrust and overhung loads; refer such applications to Application Engineering (1 800 66 09). Interpolate for loads at other distances from the housing surface. Overhung load must be applied on the same side as the bushing. 140

SMTP, MTP, CMTP Thrust and Overhung Load Capacity (Lbs.) Unit 07608 Double Reduction Reducers Reducer R.P.M. 0 0 40 50 60 70 80 90 0 1 140 150 160 170 180 190 00 Thrust Load 850 850 850 850 850 850 850 850 850 8 811 7909 7698 7487 775 7064 685 6641 640 1 07MTP09 07MTP15 07MTP5 07MTP5 OL at Inches from Machined ousing Surface 4 8 1 907 7080 60 5480 505 469 44 40 4018 86 71 587 470 67 68 18 7 05 97 90 805 685 5415 4865 4470 4167 97 7 567 48 97 18 080 988 90 87 758 695 68 58 705 5490 470 450 905 640 40 60 115 995 880 780 690 6 55 470 4 55 05 5 6 9 8 5 Reducer R.P.M. 0 0 40 50 60 70 80 90 0 1 140 150 160 170 180 190 00 Thrust Load 8840 8840 8840 8840 74 6750 60 580 540 5 5070 4940 480 470 459 4476 460 44 416 00 15MTP09 15MTP15 15MTP5 15MTP5 OL at Inches from Machined ousing Surface 4 8 1 188 865 98 8447 7780 767 685 6515 6 598 576 5570 540 550 51 4980 4858 4750 4655 55 148 9665 847 751 690 646 6097 5795 557 5 517 4955 4807 4670 4545 440 4 45 4140 05 815 8465 7 6580 6060 5660 540 5075 4850 4660 4490 440 4 4090 980 880 785 700 65 55 4 9 4 7 4 0 Reducer R.P.M. Thrust Load 407SMTP15 407SMTP5 OL at Inches from Machined ousing Surface 4 8 1 9000 17 988 8605 0 898 80 718 65 0 6586 6518 579 5065 40 4874 5570 4950 40 50 444 4900 455 8 60 81 49 90 415 70 8 995 550 5 80 91 4017 566 115 90 579 408 58 15 0 6 4060 598 15 1 1874 408 61 145 1760 4 69 155 1645 415 645 165 Shaft Mount Engineering Reducer 415SMTP15 415SMTP5 Reducer 507SMTP15 507SMTP5 Reducer 608SMTP15 608SMTP5 R.P.M. 0 0 40 50 60 70 80 90 0 1 Thrust Load 0 0 0 11700 600 9777 895 8 7675 70 6960 6700 6440 OL at Inches from Machined ousing Surface 4 8 1 1575 974 746 6055 5477 5185 4948 4755 459 4450 417 408 41 75 861 6598 555 484 4585 477 405 406 95 818 7 65 575 7485 575 4655 4 985 805 655 50 40 0 5 160 R.P.M. 0 0 40 50 60 70 80 90 0 1 Thrust Load 1900 1900 1900 1900 1900 0 11500 800 0 000 9950 9900 980 OL at Inches from Machined ousing Surface 4 8 1 169 185 80 985 917 875 8 7998 777 748 775 708 6918 158 11450 9670 8797 88 7790 748 714 6898 668 6495 6 6177 195 075 85 7740 740 6855 6545 685 6070 5880 5715 5565 545 R.P.M. 0 0 40 50 60 70 80 90 0 1 Thrust Load 000 000 1600 190 17600 16400 15450 14500 1116 11909 70 9497 891 OL at Inches from Machined ousing Surface 4 8 1 0878 98 0557 1854 174 164 1567 15060 1458 14088 169 1 774 1507 18468 16658 1558 1475 1408 150 6 1657 11978 11698 4605 19075 1680 14775 180 85 1490 00 11585 115 9 65 75 Reducer 800SMTP5 R.P.M. 0 0 40 50 60 70 80 Thrust Load 060 060 9808 658 488 6 11 00 OL at Inches from Machined ousing Surface 4 8 1 56746 450 701 916 0005 7790 60 4560 5588 4799 6414 8 950 740 560 416 549 4095 5815 1850 905 6890 5180 765 Notes: Above thrust and overhung loads are not applicable for combined thrust and overhung loads; refer such applications to Application Engineering (1 800 66 09). Interpolate for loads at other distances from the housing surface. Overhung load must be applied on the same side as the bushing. 141

SMTP, MTP, CMTP Minimum Shaft Length Requirements Front Mounting Configuration with Stabilizer Ring Rear Mounting Configuration with Stabilizer Ring Rear Mounting Configuration without Stabilizer Ring MC MC MC K C K K MC MC MC Unit Endcap Clearance Fig. 1 Fig. Fig. Minimum Shaft Mounting Length Minimum Key Connection Length MC K* 7 0.97 8.06.69 115 1.0 8.59.88 0 1.15 9.78 4. 07 1.1.16 4.81 15 1.1 11.6 5.5 07 1.44 1.04 6.1 15 1.69 15.0 7.8 407 415 507 608 800 Minimum Minimum Remaining olt Shaft Key Shaft for Unit Clearance Mounting Connection Stabilizer Length Length Ring MC K* C 7 1.75 9.5.69.40 115 1.88.1.88.6 0 1.88 11.19 4. 4.19 07 1.88 11.5 4.81 4.01 15 1.88 1.6 5.5 4.61 07.5 14.64 6.1 5.01 15.75 17.07 7.8 5.76 407.75 16.4 6.91 5.54 415.5 19.76 8.5 6.51 507.75 1.7 9.66 6.7 608 4.5 5.9.15 9.68 800 4.50 8.6.7 11.1 Unit olt Clearance Minimum Shaft Mounting Length Minimum Key Connection Length MC K* 7 1.75 6.1.69 115 1.88 6.50.88 0 1.88 7.00 4. 07 1.88 7.50 4.81 15 1.88 8.00 5.5 07.5 9.6 6.1 15.75 11.1 7.8 407.75.88 6.91 415.5 1.5 8.5 507.75 15.00 9.66 608 4.5 16.5.15 800 4.50 17.50.7 *K Minimum key connection length is measured from the end of the driven shaft to the end of the usable keyseat. Note: 407800 mounting systems available in rear configuration only. Contact Application Engineering (1 800 66 09) for front configuration mounting systems on these sizes. 14

Shaft Mount Engineering Don t Let An Ounce of Dirt Stop 1,000 Tons of Rock!! Performance is Our Pledge rowning Patented arrier Seal System Combines a vring face seal, grease filled labyrinth and rotating outer flinger to provide triple protection to reduce contamination and oil seal damage. Standard on all shafts. 14

SMTP, MTP, CMTP Face Mounting Drill and Tap Instructions Unit s 715 C A Tap (6 oles) "" Tap (4 oles) "A" C D E F Reducer 7 Reducer 7 oles Notes: No extra charge for drilled and tapped holes. Please specify at time of order. Full diameter of drill must not exceed specified drill depth because point of drill may break through housing and contaminate the oil with metal chips. 144 Tap Tap Depth Drill Depth 5/1618 0.56 0.75 115 /816 0.69 0.88 0 0.69 0.88 7/1614 07 6 0.81 1.00 15 1/1 0.81 1.00 07 15 "A" PreMachined Face Mount oles (Machined at Factory) oles Tap Tap Depth "" Optional Face Mount oles (Not Machined) Drill Depth 5/1618 0.6 0.75 4.15 115 /816 0.88 1.1 5.060 0 7/1614 0.88 1.1 5.500 07 4 1.06 1.1 6.75 1/1 15 0.81 1.1 6.875 07 1.16 1.44 8.75 5/811 15 1.5 1.50 9.15 Reducer A C D E F 7 1.14.81 1.59 5.59 1.19.00 115 1.7.1 1.5 6.41 1.8.01 0 1.55.8.1 7.41 1.69 4.1 07 1.87 4.64.66 8.94 1.97 5.00 15.15 5..6.8.5 5.75 07.44 6.0.75 11.8.6 6.50 15.5 6.5 1.81 1.1.75 6.75 5/811 1.00 1.19 C

SMTP, MTP, CMTP Face Mounting Drill and Tap Instructions Unit s 407800 A C Tap (6 oles) Tap (4 oles) Shaft Mount Engineering C D F E "A" Face Mount oles (Machined at Factory) Reducer Tap Tap Drill oles Depth Depth C 407 1.06 1.7.15 415 6 5/811 1.1 1.44 1.50 507 1.1 1.6 1.688 608 /4 1.56 1.88 15.750 8 800 7/89.00.5 18.50 "" Face Mount oles (Not Machined) Reducer A C D E F 407 7.48.00 4.6 1.86.1 7.75 415 8.4.5 5.19 15.47.6 8.7 507 4.98 8.61 5.89 17.5 4.19 9.94 608 7. 5 7.50 6.81 0.00 4.5.59 800 9.75 8.1 6.50 0.78.41 1.75 Reducer Tap Tap Drill oles Depth Depth 407 415 1.00 1.19 /4 507 6 608 1.8 1.69 800 18 1.56 1.88 Notes: No extra charge for drilled and tapped holes. Please specify at time of order. Full diameter of drill must not exceed specified drill depth because point of drill may break through housing and contaminate the oil with metal chips. 145

SMTP, MTP, CMTP Lubrication s 7800 The drawing below shows the breather, magnetic drain and oil level plug locations for the standard mounting positions. The breather is installed in the fill hole in the top and the magnetic drain plug is installed in the bottom of the reducer in its relative position. Use oil level A for speeds slower than those shown in the table below. Use oil level for speeds faster than those shown in the table below. Refer to mounting positions and lubrication tables shown below for proper oil levels on 7608 sizes. Refer to mounting positions and lubrication tables shown below for proper oil levels on 800SMTP. Vertical shaft mounting positions OIL LEVEL OIL LEVEL 146

SMTP, MTP, CMTP Lubrication s 7800 Shaft mount reducers require different amounts of oil in the various mounting positions. For the convenience of having enough oil at the installation site, the table below shows the approximate amount of oil for each mounting position. Refer to mounting positions and lubrication tables shown below for proper oil levels. Use Oil Level For Speeds Faster Than Those Shown elow Reducer for Reducer Ratios 5:1 9:1 15:1 5:1 5:1 7 400 184 70 40 115 8 17 70 40 0 6 18 11 70 40 07 75 11 99 70 40 15 6 97 85 70 40 07 04 90 79 70 40 15 0 85 6 70 40 407 176 6 55 415 156 5 46 507 47 41 608 46 40 800 40 Approximate Oil Capacities in Quarts Orientation orizontal Ratio 5:1 9,15,5,5:1 Oil Level A A Mounting Position 6 9 1 6 9 1 6 9 1 6 9 1 7.0.0.5.0 1.0 1.0 1.5 1.5.0.0.0.0 1.0 1.0 1.5 1.5 115.0.0.0.0 1.5.0.0.0.0.0.0.0 1.5.0.0.0 0 5.0 5.0 6.0 5.0.5.0.5.5 4.5 4.5 5.5 5.0.5.0.5.5 07 6.5 7.0 7.5 7.0.0 4.0 4.5 4.5 6.0 6.5 7.5 7.0.0 4.0 4.5 4.5 15 9.0.0 11.5.5 4.0 5.5 7.0 6.0 8.0 9.0 11.0.0 4.0 5.0 7.0 6.0 07 1.0 1.5 15.5 14.0 7.0 8.5.0 9.5 1.0 1.5 15.0 14.0 7.0 8.0.0 9.5 15 17.0 19.5 19.5 17.5.0 1.5 1.0 11.0 15.5 18.0 19.0 17.0 9.5 11.5 1.0 11.0 407 19.0 0.1.5 19.8 8.4 1. 1.5 1.7 15.9 17.1 1.7 19. 7.8. 1.8 1.7 415.5 4.0 40.0 4.8 15. 0.9.8.5 7.8 9.7 7.5.8 14. 18.0 4..5 507 8. 40. 5.9 49.4 19.7.5 4.8.9 608 55.0 61.5 65.4 68. 40. 6.8 50.4 4.9 800 94.6 90.0 91.0 74. 69.5 Shaft Mount Engineering Orientation Vertical Ratio 5:1 9,15,5,5:1 Mounting Position Shaft Up Shaft Down Shaft Up Shaft Down 7.5.5.5.5 115.5 4.0.5 4.0 0 6.0 7.0 6.0 7.0 07 8.5 9.0 8.5 9.0 15 1.0 1.5 1.0 1.0 07 18.5 0.0 17.5 19.0 15 4.0 6.0.5 5.0 407 6.5 9.0 4.0 6.5 415 46. 50. 4.5 46. 507 60.8 65.8 608 87.9 9.9 800 144. 145. Notes: Contact Application Engineering (1 800 66 09) for vertical shaft mounting lubrication instructions. SMTP, SMFP, MTP and CMTP reducers are shipped without oil. Gearboxes must be filled to the proper level before operation. Synthetic or mineral oil may be used in SMTP, SMFP, MTP and CMTP shaft mount reducers. For complete lubrication instructions, refer to the installation manual provided with the unit. Reference page 148 for additional lubrication specifications. 147

SMTP, MTP, CMTP Lubrication s 7800 NOTICE: Petroleumbased and synthetic lubricants which contain antiwear/extreme pressure additives must not be used in units with internal backstops. These additives decrease the backstop's ability to prevent reverse rotation and will result in backstop failure. Note: Reducers operating more than from standard position should have a stand pipe or sight glass installed and marked at proper oil level in order to monitor oil level while in operating position. Contact Application Engineering (1 800 66 09) Department for assistance in selecting and installing required material. Relubrication The following are some general recommendations regarding relubrication. Your experience in your specific application is the best determination of relubrication intervals. Petroleumbased lubricants For normal operating conditions, oil should be changed every,500 hours or six months, whichever occurs first. If temperatures vary by season, the oil should be changed to suit the ambient operating temperature. Synthetic Lubricants Some type of synthetic lubricants can be used in shaft mount reducers. These lubricants can extend oil change intervals to as much as 8,000 to,000 hours based on operating temperatures and lubricant contamination. If temperatures vary by season, the oil should be changed to suit the ambient operating temperature. 148

SMTP, MTP, CMTP Lubrication s 7800 RPM AGMA Oil Viscosity Grades for Ambient Operating Temperature between 14 deg F and 50 deg F Reducer 7MTP 115MTP 0MTP 07MTP 15MTP 07MTP 15MTP 407SMTP 415SMTP 507SMTP 608SMTP 800SMTP 50 5 5 5 5 5 5 5 5 5 5 5 5 140 5 5 5 5 5 5 5 5 5 5 5 5 4160 5 5 5 5 5 5 5 5 5 5 5 5 6180 5 5 5 5 5 5 5 5 5 5 5 5 810 5 5 5 5 5 5 5 5 5 5 5 1 5 5 5 5 5 5 5 5 5 5 5 11140 5 5 5 5 5 5 5 5 5 141160 5 5 5 5 5 5 5 5 5 161180 5 5 5 5 5 5 5 5 5 180 5 5 5 5 5 5 5 5 5 0 5 5 5 5 5 5 5 5 4 140 5 5 5 5 5 5 5 4 4 4160 5 5 5 5 5 5 5 4 4 6180 5 5 5 5 5 5 4 4 4 80 5 5 5 5 5 4 4 4 4 0 5 5 5 5 4 4 4 4 4 140 5 5 5 5 4 4 4 4 4 4160 5 5 5 5 4 4 4 4 4 6180 5 5 5 4 4 4 4 4 4 81400 5 5 5 4 4 4 4 4 4 Shaft Mount Engineering RPM AGMA Oil Viscosity Grades for Ambient Operating Temperature between 50 deg F and 95 deg F Reducer 7MTP 115MTP 0MTP 07MTP 15MTP 07MTP 15MTP 407SMTP 415SMTP 507SMTP 608SMTP 800SMTP 50 6 6 6 6 6 6 6 6 6 6 6 6 140 6 6 6 6 6 6 6 6 6 6 6 6 4160 6 6 6 6 6 6 6 6 6 6 6 6 6180 6 6 6 6 6 6 6 6 6 6 6 6 810 6 6 6 6 6 6 6 6 6 6 6 1 6 6 6 6 6 6 6 6 6 6 6 11140 6 6 6 6 6 6 6 6 6 141160 6 6 6 6 6 6 6 6 6 161180 6 6 6 6 6 6 6 6 6 180 6 6 6 6 6 6 6 6 5 0 6 6 6 6 6 6 6 5 5 140 6 6 6 6 6 6 5 5 5 4160 6 6 6 6 6 6 5 5 5 6180 6 6 6 6 6 5 5 5 5 80 6 6 6 6 6 5 5 5 5 0 6 6 6 6 5 5 5 5 5 140 6 6 6 6 5 5 5 5 5 4160 6 6 6 6 5 5 5 5 5 6180 6 6 6 5 5 5 5 5 5 81400 6 6 6 5 5 5 5 5 5 149

RC Drives Features and Ratings Water treatment maintenance superintendents, design engineers and consultants agree... rowning products meet all your needs for rotating biological contactor drives. Specify the rowning solution on your next RC installation or retrofit. Superior RC Drive Solutions uilt Rugged and Dependable for Minimal Maintenance and Downtime RC Split Power Path Shaft Conventional Shaft Mount Power Path ore Split Power Path Design Provides twice the tooth engagement when compared to conventional drives Leak Free Operation Plunge ground shafts with dual lip oil seals igh Quality earings 0,000 hour life at 5 hp Class II service Generous Shaft Diameters Support overhung loads generated by Vbelt drive assembly Compact design and dropin features allow for quick replacement of problem drives Universal housings allow for left or righthand installations Reducer, belt guard, torque arm, belt drive and motor are to be ordered separately 150

RC Drives Dimensions Standard Unit Drive Assembly 1.88 15.55 17.8 4.975 ore & 1.50 WD x.8 DP Keyway 6.75 Level Gauge 1.65 Dia. &.8 x.8 x 4.50 Keyway 6.8 1.88 x 1.1 Slot as Shown Fiberglass Velt Guard Arm Tapered ushed Unit P/N 415SMT148 includes 4 15/16" tapered bushing and standard motor mount. Straight ore Unit P/N 415SMF148 Includes Std. Motor Mount Motor mount will accept... 184T, 1T & 54T* frame motors and a V belt drive CD of 14 to 0" Fiberglass Velt Guard P/N G415RC Arm P/N TA415RC/1 Shaft Mount Engineering 17.00* Center Line SG Sight Glass 40.75.75* 8.50 * If torque arm arrangement is longer than.75" in the horizontal, or smaller than 17.00 in the vertical dimension, contact Application Engineering (1 800 66 09). ostile duty totally enclosed fan cooled motors Designed for wastewater treatment plant operation igh efficiency EPAct 9 certified Cast iron frames ostileduty paint Stainless steel nameplates rowning RC Drive Ratings Motor hp/ Part Number 5/1150 5ED 7.5/1150 7ED Motor Frame AGMA Service Factor Velt Drive Ratio Gear Drive Ratio Final Speed Final Rating 15T Class II 5.: 1 148: 1 1.5 RPM 199,600 in./lbs. 54T Class I 5.: 1 148: 1 1.5 RPM 97,400 in./lbs. 151

All sales are made on our STANDARD TERMS AND CONDITIONS OF SALE in effect at the time a customer s order is accepted. The current Terms and Conditions are set forth below: STANDARD TERMS AND CONDITIONS OF SALE (September, 009) These Terms and Conditions, the attendant quotation or acknowledgment and all documents incorporated by specific reference therein, will be the complete and exclusive statement of the terms of the agreement governing the sale of goods ( Goods ) by Emerson Power Transmission Corporation and its divisions and subsidiaries ( Seller ) to Customer ( uyer ). uyer s acceptance of the Goods will manifest uyer s assent to these Terms and Conditions. If these Terms and Conditions differ in any way from the terms and conditions of uyer s order, or other documentation, this document will be construed as a counteroffer and will not be deemed an acceptance of uyer s terms and conditions which conflict herewith. 1. PRICES: Unless otherwise specified in writing by Seller, Seller s price for the goods shall remain in effect for thirty (0) days after the date of Seller s quotation or acknowledgment of uyer s order for the Goods, whichever occurs first, provided an unconditional, complete authorization for the immediate shipment of the Goods is received and accepted by Seller within such time period. If such authorization is not received by Seller within such thirty (0) day period, Seller shall have the right to change the price for the Good to Seller s price for the Goods at the time of shipment.. TES: Any tax or governmental charge or increase in same hereafter becoming effective increasing the cost to Seller of producing, selling or delivering the Goods or of procuring material used therein, and any tax now in effect or increase in same payable by the Seller because of the manufacture, sale or delivery of the Goods, may at Seller s option, be added to the price.. TERMS OF PAYMENT: Subject to the approval of Seller s Credit Department, terms are net thirty (0) days from date of Seller s invoice in U.S. currency. If any payment owed to Seller is not paid when due, it shall bear interest, at a rate to be determined by Seller, which shall not exceed the maximum rate permitted by law, from the date on which it is due until it is paid. Seller shall have the right, among other remedies, either to terminate the Agreement or to suspend further performance under this and/or other agreements with uyer in the event uyer fails to make any payment when due. uyer shall be liable for all expenses, including attorneys fees, relating to the collection of past due amounts. 4. SIPMENT AND DELIVERY: Shipments are made F.O.. Seller s shipping point. Any claims for shortages or damages suffered in transit shall be submitted by the uyer directly to the carrier. While Seller will use all reasonable commercial efforts to maintain the delivery date acknowledged or quoted by Seller, all shipping dates are approximate. Seller reserves the right to make partial shipments and to segregate specials and madetoorder Goods from normal stock Goods. Seller shall not be bound to tender delivery of any Goods for which uyer has not provided shipping instructions. 5. QUANTITY: uyer agrees to accept overruns of up to ten percent (%) of the order on madetoorder Goods, including parts. Any such additional items shall be priced at the price per item charged for the specific quantity ordered. 6. LIMITED WARRANTY: Subject to the limitations of Section 7, Seller warrants that the Goods will be free from defects in material and workmanship under normal use, service and maintenance for a period of one year (unless otherwise specified by Seller in writing) from the date of shipment of the Goods by Seller. TIS IS TE SOLE AND EXCLUSIVE WARRANTY GIVEN Y SELLER WIT RESPECT TO TE GOODS AND IS IN LIEU OF AND EXCLUDES ALL OTER WARRANTIES, EXPRESS OR IMPLIED, ARISING Y OPERATION OF LAW OR OTERWISE, INCLUDING WITOUT LIMITATION, MERCANTAILITY OR FITNESS FOR A PARTICULAR PURPOS WETER OR NOT TE PURPOSE OR USE AS EEN DISCLOSED TO SELLER IN SPECIFICATIONS, DRAWINGS OR OTERWISE, AND WETER OR NOT SELLER S PRODUCTS ARE SPECIFICALLY DESIGNED AND/OR MANUFACTURED Y SELLER FOR UYER S USE OR PURPOSE. This warranty does not extend to any losses or damages due to misuse, accident, abuse, neglect, normal wear and tear, unauthorized modification or alteration, use beyond rated capacity, or improper installation, maintenance or application. To the extent that uyer or its agents has supplied specifications, information, representation of operating conditions or other data to Seller in the selection or design of the Goods and the preparation of Seller s quotation, and in the event that actual operating conditions or other conditions differ from those represented by uyer, any warranties or other provisions contained herein which are affected by such conditions shall be null and void. If within thirty (0) days after uyer s discovery of any warranty defects within the warranty period, uyer notifies Seller thereof in writing, Seller shall, at its option, repair or replace F.O.. point of manufacture, or refund the purchase price for, that portion of the goods found by Seller to be defective. Failure by uyer to give such written notice within the applicable time period shall be deemed an absolute and unconditional waiver of uyer s claim for such defects. Goods repaired or replaced during the warranty period shall be covered by the foregoing warranty for the remainder of the original warranty period or ninety (90) days, whichever is longer. uyer assumes all other responsibility for any loss, damage, or injury to persons or property arising out of, connected with, or resulting from the use of Goods, either alone or in combination with other products/components. SECTIONS 6 AND 7 APPLY TO ANY ENTITY OR PERSON WO MAY UY, ACQUIRE OR USE SELLER S GOODS, INCLUDING ANY ENTITY OR PERSON WO UYS TE GOODS FROM SELLER S DISTRIUTOR AND SUC ENTITY OR PERSON SALL E OUND Y TE LIMITATIONS TEREIN. 7. LIMITATION OF REMEDY AND LIAILITY: TE SOLE AND EXCLUSIVE REMEDY FOR REAC OF ANY WARRANTY EREUNDER (OTER TAN TE WARRANTY PROVIDED UNDER SECTION 1) SALL E LIMITED TO REPAIR, REPLACEMENT OR REFUND OF TE PURCASE PRICE UNDER SECTION 6. SELLER SALL NOT E LIALE FOR DAMAGES CAUSED Y DELAY IN PERFORMANCE AND IN NO EVENT, REGARDLESS OF TE FORM OF TE CLAIM OR CAUSE OF ACTION (WETER ASED IN CONTRACT, INFRINGEMENT, NEGLIGENCE, STRICT LIAILITY, OTER TORT OR OTERWISE), SALL SELLER S LIAILITY TO UYER AND/OR ITS CUSTOMERS EXCEED TE PRICE TO UYER OF TE SPECIFIC GOODS PROVIDED Y SELLER GIVING RISE TO TE CLAIM OR CAUSE OF ACTION. UYER AGREES TAT IN NO EVENT SALL SELLER S LIAILITY TO UYER AND/OR ITS CUSTOMERS EXTEND TO INCLUDE INCIDENTAL, CONSEQUENTIAL OR PUNITIVE DAMAGES. TE TERM CONSEQUENTIAL DAMAGES SALL INCLUDE, UT NOT E LIMITED TO, LOSS OF ANTICIPATED PROFITS, LOSS OF USE, LOSS OF REVENUE, COST OF CAPITAL AND DAMAGE OR LOSS OF OTER PROPERTY OR EQUIPMENT. It is expressly understood that any technical advice furnished by Seller with respect to the use of the Goods is given without charge, and Seller assumes no obligation or liability for the advice given, or results obtained, all such advice being given and accepted at uyer s risk. GOODS AND/OR SERVICES SOLD EREUNDER ARE NOT FOR USE IN ANY NUCLEAR AND RELATED APPLICATIONS. uyer accepts goods and/or services with the foregoing understanding, agrees to communicate the same in writing to any subsequent purchaser or users and to defend, indemnify and hold harmless Seller from any claims, losses, suits, judgments and damages, including incidental and consequential damages, arising from such use, whether the cause of action be based in tort, contract or otherwise, including allegations that the Seller's liability is based on negligence or strict liability. 8. EXCUSE OF PERFORMANCE: Seller shall not be liable for delays in performance or for nonperformance due to acts of God, acts of uyer, war, riot, fire, flood, other severe weather, sabotage, or epidemics; strikes or labor disturbances; governmental requests, restrictions, laws, regulations, orders or actions; unavailability of or delays in transportation; default of suppliers; or unforeseen circumstances or any events or causes beyond Seller s reasonable control. Deliveries may be suspended for an appropriate period of time as a result of the foregoing. If Seller determines that its ability to supply the total demand for the Goods, or to obtain material used directly or indirectly in the manufacture of the Goods, is hindered, limited or made impracticable due to causes addressed in this Section 8, Seller may allocate its available supply of the Goods or such material (without obligation to acquire other supplies of any such Goods or material) among itself and its purchasers on such basis as Seller determines to be equitable without liability for any failure of performance which may result therefrom. Deliveries suspended or not made by reason of this section may be canceled by Seller upon notice to uyer without liability, but the balance of the agreement shall otherwise remain unaffected. 9. CANCELLATIONS AND DELAYS: The uyer may cancel orders only upon written notice and upon payment to Seller of cancellation charges which include, among other things, all costs and expenses incurred and commitments made by the Seller and a reasonable profit thereon. Any request by uyer to extend the delivery schedule must be agreed to in writing by the Seller. If agreement cannot be reached, Seller may deliver product to the last known ship to address and invoice the uyer upon completion of the product or prior delivery date, whichever is later.. CANGES: uyer may request changes or additions to the Goods consistent with Seller s specifications and criteria. In the event such changes or additions are accepted by Seller, Seller may revise the price and delivery schedule. Seller reserves the right to change designs and specifications for the Goods without prior notice to uyer, except with respect to Goods being madetoorder for uyer. 11. TOOLING: Tool, die, and pattern charges, if any, are in addition to the price of the Goods and are due and payable upon completion of the tooling. All such tools, dies and patterns shall be and remain the property of Seller. Charges for tools, dies, and patterns do not convey to uyer, title, ownership interests in, or rights to possession or removal, nor prevent their use by Seller for other purchasers, except as otherwise expressly provided by Seller and uyer in writing with reference to this provision. 1. ASSIGNMENT: uyer shall not assign its rights or delegate its duties hereunder or any interest therein or any rights hereunder without the prior written consent of the Seller, and any such assignment, without such consent, shall be void. 1. PATENTS AND COPYRIGTS: Subject to Section 7, Seller warrants that the Goods sold, except as are made specifically for uyer according to uyer s specifications, do not infringe any valid U.S. patent or copyright in existence as of the date of delivery. This warranty is given upon the condition that uyer promptly notify Seller of any claim or suit involving uyer in which such infringement is alleged, and, that uyer cooperate fully with Seller and permit Seller to control completely the defense or compromise of any such allegation of infringement. Seller s warranty as to use only applies to infringements arising solely out of the inherent operation (i) of such Goods, or (ii) of any combination of Goods in a system designed by Seller. In the event such Goods, singularly or in combination, are held to infringe a U.S. patent or copyright in such suit, and the use of such Goods is enjoined, or in the case of a compromise by Seller, Seller shall have the right, at its option and expense, to procure for uyer the right to continue using such Goods, or replace them with noninfringing Goods; or modify same to become noninfringing; or grant uyer a credit for the depreciated value of such Goods and accept return of them. 14. MISCELLANEOUS: These terms and conditions set forth the entire understanding and agreement between Seller and uyer, and supersede all other communications, negotiations and prior oral or written statements regarding the subject matter of these terms and conditions. No change, modification, rescission, discharge, abandonment, or waiver of these terms and conditions of Sale shall be binding upon the Seller unless made in writing and signed on its behalf by an officer of the Seller. No conditions, usage or trade, course of dealing or performance, understanding or agreement purporting to modify, vary, explain, or supplement these Terms and Conditions shall be binding unless hereafter made in writing and signed by the party to be bound, and no modification shall be affected by the acceptance of purchase orders or shipping instruction forms containing terms at variance with or in addition to those set forth herein. Any such modifications or additional terms are specifically rejected by Seller. No waiver by Seller with respect to any breach or default or any right or remedy and no course of dealing, shall be deemed to constitute a continuing waiver of any other breach or default or of any other right or remedy, unless such waiver be expressed in writing and signed by the party to be bound. Seller is not responsible for typographical or clerical errors made in any quotation, orders or publications. All such errors are subject to correction. The validity, performance, and all other matters relating to the interpretation and effect of this contract shall be governed by the law of the state of New York. The United Nations Convention on the International Sale of Goods shall not apply to any transaction hereunder. 495