MRL UIL OLLTION Installation Guide
Panel to Panel onnector VIW VIO for Panel to Panel onnector: http://www.youtube.com/watch?feature=player_embedded&v=5s4zwoa9u7c#at=43 This onnects 2 Panels Together Side by Side Mid-Panel lip Panel-to-Panel Foot Panel-to-Panel Small lip Foot Panel-to-Panel Straight Top onnector
T-onnection This onnects 3 Panels Together in T onfiguration VIW VIO for T-onnector: http://www.youtube.com/watch?feature=player_embedded&v=o_leoww78fo Foot 3 Way T Top onnector 3 Way T ottom onnector 2 Way Mounting Support racket
VIW VIO - X-onnector: http://www.youtube.com/watch?feature=player_embedded&v=ou8zzm4fyo8#at=48 X-onnectors This onnects 4 Panels Together in X onfiguration Foot 4 Way X ottom onnector 2 Way Mounting Support 4 Way X Top onnector
VIW VIO - L-onnector: http://www.youtube.com/watch?feature=player_embedded&v=l9kmo7nht4 L-onnectors This onnects 2 Panels Together in L onfiguration Foot 2 Way L ottom onnector racket L-racket 2 Way L Top onnector
nd ap nd Trim Foot racket Foot nd ap (available in 42, 52, and 65 ) nd of Run Top ap
antilevers & Worksurfaces (Left) Single antilever Flat racket (Right) Single antilever ouble antilever orner Worksurface Support (2 Styles)
Wall Mounted Panels VIW INSTLLING a Wall Mount Video: http://www.youtube.com/watch?v=5d8oix2w Wall Mount onnector Use two (2) brackets. o NOT put end cap on. Push panel against bracket. The weight of the panel will hold panel in place.
aster Installation VIW INSTLLING a Rolling or Stationary Panel: http://www.youtube.com/watch?feature=player_embedded&v=mwhr4upom#at=20 Panel Support Legs With asters Panel Support Legs Without asters
Straight Step-own From 52 to 42 Panel Joint onnector Small nd ap 13 3/4 nd Trim** Joint onnector 34 1/8 Top ap* 52 H 42 H * This ap replaces the original cap that came with the panel. **Note: If the step-down is a 65 Panel to a 42 Panel, the nd Trim will be 24 1/8. If the step-down is a 65 Panel to a 52 Panel, the nd Trim will be 10 1/4.
Transaction Top 1. Remove Top aps from Panels. 2. Install Transaction Top Support rackets. (Front and ack of Panels) 3. enter and Place Transaction Top(s) 3. Secure Transaction Top(s) by screwing through holes in brackets into Top from underneath.
onnectors 1. 2. 3. 4. 5. nd ap Straight onnector Straight Step 2 Way onnector 2 Way Step own own onnector onnector 6. 7. 8. 9. 10. 3 Way onnector 3 Way Step own 3 Way Step own Interior onnector xterior onnector 4 Way onnector 4 Way Step own onnector
lectric and ata The Power System is an eight wire system consisting of four individual circuits (see Fig. 1). ach ircuit is rated at 20amps/120 volts maximum. ircuit 1 (black), ircuit 2 (red) and ircuit 4 (pink), are served by a system neutral (white) and an equipment ground (green). ircuit 3 (blue) uses an isolated neutral (gray), and an isolated ground (green/yellow). The system may be supplied by a three phase power system with four individual ircuits rated at 20amps/120 volts maximum, or as permitted by local code. When connecting electric pass throughs to power moduals, please make sure RROW is up! 3-H 3G 1-2-4G 3N 1-2-4N 1H 2H 4H FIG 1 Panel Shown Without lectric Hinged Racetrack door open to show area for electric and wired management uilding lectric In Feed ase Power Feed! FINL ONNTION IS ON Y LINS LTRIIN. WRNING: Risk of Fire or lectrical Shock. s with all non-directional systems, o Not electrically connect panel to more than one supply source. lways determine that the panel is electrically connected to one and only one source of supply. efore using any equipment, check the entire system for polarity, continuity, and grounding integrity. Panel Shown with lectric Shown with lectric (you can order 1, 2, or 3 and dedicated outlets) Shown with lectric Module, ata, and Phone Show with lectric and Phone (aditional jacks can be addedup to 4 slots)
Layouts ustomer Service onfigurations L-01 L-02 L-03 L-04 L-05 all enter onfigurations -01-02 -03-04 -05 L-08 L-09 L-10 L-11 L-12-08 -09-10 -11-12 L-06 L-07-06 -07 L-13 L-14 L-15 L-16 L-17-13 -14-15 xecutive onfigurations X-R-01 X-01 X-02