0B-KG/200B-KG Distributed By: M&M Control Service, Inc. Phone: 00-7-003 Fax: 7-3-077 Email: sales@mmcontrol.com
MODEL 0B-KG Pump Suction Control Valve Adjustable Opening Speed For Pump Suction Protection Pilot Control Provides Wide Flow Range With Minimal Pressure Variations Controlled Closing For System Protection Modulates Within % of Setting for Accurate Pressure Control Pressure Setting Adjustable Pressure Setting Not Affected by Pressure at Valve Discharge 0B-KG The Model 0B-KG Pump Suction Control Valve is designed specifically for Fire Pump Suction Control Service. It modulates to maintain the pump discharge in relation to the suction head available, thus assuring that the suction head pressure does not fall below the pre-set minimum. Typical Installation Specifications When there is a demand in the Fire System, the pump is started, delivering water from the supply source to the area of demand. To assure that the fire pump draw does not exceed the available water supply, the Model 0B-KG, sensing the pump suction, modulates to prevent suction pressure from dropping below a pre-set minimum. By maintaining minimum pressure requirements in the supply main, the main is protected from possible damage or backflow conditions. Also, a minimum supply pressure is provided for local fire apparatus. REMOTE SENSING LINE TO FIRE SERVICE SYSTEM Sizes End Details Pressure Ratings Temperature Range Materials Globe: 3" - " flanged Angle: 3" - " flanged 0 and 300 ANSI B.2 0 class - 20 psi Max. 300 class - 00 psi Max Water, to +0 F Max. Main valve body & cover Ductile Iron ASTM A-3 Main valve trim: Brass QQ-B-2 Bronze Seat ASTM B Stainless Steel Stem 303 Delrin Sleeved Pilot control system: Cast Bronze ASTM B2 with 303 Stainless Steel trim SUPPLY SYSTEM FIRE PUMP CLA-VAL 0B-KG Adjustment Range Available in the following pressure range only: to 2 psi Set at 0 psi
Dimensions (in Inches) Flow Chart E (MAX.) 2 PRESSURE RELIEF CONTROL ADJUSTMENT: TURN THE ADJUSTING STEM CLOCKWISE TO INCREASE THE SETTING. REMOTE SENSING LINE CONNECTION: /" - 27 N.P.T. Pressure Drop - psi INLET OUTLET K C CC D DD Item No. 2 3 A BB 00KCGVX Hytrol (Main Valve) CRLA Pressure Relief Control XA Strainer and Orifice Assembly CV Flow Control (Opening) X0C Valve Position Indicator CK2 (Blow-Off Valve) B AA (" SIZE VALVE SHOWN) INLET (ANGLE PATTERN) Description G F (MAX.) 3 Flow - Gallons Per Minute OPENING SPEED CONTROL ADJUSTMENT: TURN THE ADJUSTING SCREW CLOCKWISE TO MAKE THE MAIN VALVE OPEN SLOWER. VALVE SIZE 3 A 0 LB. FLANGES 2.00.00 20.00 2.3 AA 300 LB. FLANGES 3.2.2 2.00 2.3 B 0 LB. FLANGES.00 7.0 0.00 2.7 BB 300 LB. FLANGES.3 7. 0.0 3.2 C 0 LB. FLANGES.00.00.00.00 CC 300 LB. FLANGES.3.3.0.0 D (TYP.) 0 LB. FLANGES (MIN.).7.9.00.2 DD (TYP.) 300 LB. FLANGES (MIN.).2.2..2 E (MAX.).7 7.7 20.2 23.00 F (MAX.) 3.0.00.0 20.00 G (MAX.).2.7 7. 0.00 K 2. 3.9.3.3 Purchase Specifications The Fire Pump Suction Control Valve shall modulate to maintain a minimum pressure at the pump suction regardless of system demand. It shall control the pump discharge in relation to the suction head available, and shall not allow suction head pressure to fall below a pre-set minimum. It shall be actuated by line pressure through a pilot control system which allows rapid response to changing pressure conditions without line surges. The pilot control shall be remote sensed to the pump suction head pressure. The main valve shall be of the hydraulically-operated, pilotcontrolled, diaphragm-type, globe or angle valve. It shall have a single removable seat, a delrin-sleeved guided stem and a renewable resilient synthetic rubber disc with a rectangular cross section, contained on three and one-half sides by a disc retainer and disc guide. No external packing glands shall be permitted and the diaphragm shall not be used as a seating surface. The pilot control shall be a direct-acting, adjustable, spring-loaded, diaphragm-type valve designed for modulating service to permit flow when controlling pressure exceeds spring setting. A device indicating the percent at which the valve is open or closed shall be supplied on the assembly, together with a sediment evacuator and dampening device. The valve shall be designed to allow for repair and servicing without removing the valve body from the line. The valve shall be Factory Mutual Approved. It shall be the MODEL 0B-KG FIRE PUMP SUCTION CONTROL VALVE as manufactured by Cla-Val, Newport Beach, California. 0B-KG (R-/0) Distributed By: M&M Control Service, Inc. Phone: 00-7-003 Fax: 7-3-077 Email: sales@mmcontrol.com Represented By:
Description The CIa-VaI Model 00-0 Hytrol Valve is a main valve for CIa-VaI Automatic Control Valves. It is a hydraulically operated, diaphragm-actuated, globe or angle pattern valve. This valve consists of three major components; body, diaphragm assembly, and cover. The diaphragm assembly is the only moving part. The diaphragm assembly uses a diaphragm of nylon fabric bonded with synthetic rubber. A synthetic rubber disc, contained on three and one half sides by a disc retainer and disc guide, forms a seal with the valve seat when pressure is applied above the diaphragm. The diaphragm assembly forms a sealed chamber in the upper portion of the valve, separating operating pressure from line pressure. INSTALLATION / OPERATION / MAINTENANCE MODEL 00-0 Hytrol Valve Installation. Before valve is installed, pipe lines should be flushed of all chips, scale and foreign matter. 2. It is recommended that either gate or block valves be installed on both ends of the 00-0 Hytrol Valve to facilitate isoiating the valve for preventive maintenance and repairs. 3. Place the valve in the line with flow through the valve in the direction indicated on the inlet nameplate. (See Flow Direction Section). Allow sufficient room around valve to make adjustments and for disassembly.. CIa-VaI 00-0 Hytrol Valves operate with maximum efficiency when mounted in horizontal piping with the cover UP, however, other positions are acceptable. Due to size and weight of the cover and internal components of inch and larger valves, installation with the cover UP is advisable. This makes internal parts readily accessible for periodic inspection.. Caution must be taken in the installation of this valve to insure that galvanic and/or electrolytic action does not take place. The proper use of dielectric fittings and gaskets are required in all systems using dissimilar metals. 7. If a pilot control system is installed on the 00-0 Hytrol Valve, use care to prevent damage. If it is necessary to remove fittings or components, be sure they are kept clean and replaced exactly as they were.. After the valve is installed and the system is first pressurized, vent air from the cover chamber and pilot system tubing by loosening fittings at all high points. Principles of Operation Three Way Pilot Control Three Way Pilot Control Restriction Modulating Control Tight Closing Operation When pressure from the valve inlet (or an equivalent independent operating pressure) is applied to the diaphragm chamber the valve closes drip-tight. Full Open Operation When pressure in diaphragm chamber is relieved to a zone of lower pressure (usually atmosphere) the line pressure ( psi Min.) at the valve inlet opens the valve. Modulating Action Valve modulates when diaphragm pressure is held at an intermediate point between inlet and discharge pressure. With the use of a Cla-Val. "modulating control," which reacts to line pressure changes, the pressure above the diaphragm is varied, allowing the valve to throttle and compensate for the change.
Flow Direction The flow through the 00-0 Hytrol Valve can be in one of two directions. When flow is up-and-over the seat, it is in normal flow and the valve will fail in the open position. When flow is overthe seat-and down, it is in reverse flow and the valve will fail in the closed position. There are no permanent flow arrow markings. The valve must be installed according to nameplate data. BRIDGEWALL INDlCATOR (cast into side of valve body) Normal Flow Troubleshooting Reverse Flow The following troubleshooting information deals strictly with the Model 00-0 Hytrol Valve. This assumes that all other components of the pilot control system have been checked out and are in proper working condition. (See appropriate sections in Technical Manual for complete valve). Recommended Tools. Three pressure gauges with ranges suitable to the installation to be put at Hytrol inlet, outlet and cover connections. 2. Cla-Val Model X0 Valve Position Indicator. This provides visual indication of valve position without disassembly of valve. 3. Other items are: suitable hand tools such as screwdrivers, wrenches, etc. soft jawed (brass or aluminum) vise, 00 grit wet or dry sandpaper and water for cleaning. All trouble shooting is possible without removing the valve from the line or removing the cover. It is highly recommended to permanently install a Model X0 Valve Position Indicator and three gauges in unused Hytrol inlet, outlet and cover connections. SYMPTOM PROBABLE CAUSE REMEDY Closed isolation valves in control system, or in main line. Open Isolation valves. Fails to Close Lack of cover chamber pressure. Check upstream pressure, pilot system, strainer, tubing, valves, or needle valves for obstruction. Fails to Open Diaphragm damaged. (See Diaphragm Check.) Diaphragm assembly inoperative. Corrosion or excessive scale build up on valve stem. (See Freedom of Movement Check) Mechanical obstruction. Object lodged in valve. (See Freedom of Movement Check) Worn disc. (See Tight Sealing Check) Badly scored seat. (See Tight Sealing Check) Closed upstream and/or downstream isolation valves in main line. Insufficient line pressure. Replace diaphragm. Clean and polish stem. Inspect and replace any damaged or badly eroded part. Remove obstruction. Replace disc. Replace seat. Open isolation valves. Check upstream pressure. (Minimum psi flowing line pressure differential.) Diaphragm assembly inoperative. Corrosion or excessive buildup on valve stem. (See Freedom of Movement Check) Diaphragm damaged. (For valves in "reverse flow" only) Clean and polish stem. Inspect and replace any damaged or badly eroded part. Replace diaphragm. After checking out probable causes and remedies, the following three checks can be used to diagnose the nature of the problem before maintenance is started. They must be done in the order shown. Three Checks The 00-0 Hytrol Valve has only one moving part (the diaphragm and disc assembly). So, there are only three major types of problems to be considered. First: Valve is stuck - that is, the diaphragm assembly is not free to move through a full stroke either from open to close or vice versa. Second: Valve is free to move and can t close because of a worn out diaphragm. Third: Valve leaks even though it is free to move and the diaphragm isn t leaking. CAUTION: Care should be taken when doing the troubleshooting checks on the 00-0 Hytrol Valve. These checks do require the valve to open fully. This will either allow a high flow rate through the valve, or the downstream pressure will quickly increase to the inlet pressure. In some cases, this can be very harmful. Where this is the case, and there are no block valves in the system to protect the downstream piping, it should be realized that the valve cannot be serviced under pressure. Steps should be taken to remedy this situation before proceeding any further. 2
Diaphragm Check (# ). Shut off pressure to the Hytrol Valve by slowly closing upstream and downstream isolation valves. SEE CAUTION. 2. Disconnect or close all pilot control lines to the valve cover and leave only one fitting in highest point of cover open to atmosphere. 3.With the cover vented to atmosphere, slowly open upstream isolation valve to allow some pressure into the Hytrol Valve body. Observe the open cover tapping for signs of continuous flow. It is not necessary to fully open isolating valve. Volume in cover chamber capacity chart will be displaced as valve moves to open position. Allow sufficient time for diaphragm assembly to shift positions. If there is no continuous flow, you can be quite certain the diaphragm is sound and the diaphragm assembly is tight. If the fluid appears to flow continuously this is a good reason to believe the diaphragm is either damaged or it is loose on the stem. In either case, this is sufficient cause to remove the valve cover and investigate the leakage. (See Maintenance Section for procedure.) COVER CHAMBER CAPACITY (Liquid Volume displaced when valve opens) Valve size (inches) Displacement Gallons Liters /.020.07 /2.020.07 2.032.2 2 /2.03. 3.00.30.9..3 2.0.2. 0 2. 9. 2.00..0 2. 9.7 3.2 2 29.00 09. 30 2.00 97.0 3 90.00 30.0 Freedom of Movement Check (#2). Determining the Hytrol Valve s freedom of movement can be done by one of two methods.. For most valves it can be done after completing Diaphragm Check (Steps, 2, and 3). SEE CAUTION. At the end of step 3 the valve should be fully open.. If the valve has a Cla-Val X0 Position Indicator, observe the indicator to see that the valve opens wide. Mark the point of maximum opening. 7. Re-connect enough of the control system to permit the application of inlet pressure to the cover. Open pilot system cock so pressure flows from the inlet into the cover.. While pressure is building up in the cover, the valve should close smoothly. There is a hesitation in every Hytrol Valve closure, which can be mistaken for a mechanical bind. The stem will appear to stop moving very briefly before going to the closed position. This slight pause is caused by the diaphragm flexing at a particular point in the valve s travel and is not caused by a mechanical bind. 9. When closed, a mark should be made on the X0 Valve position indicator corresponding to the closed position. The distance between the two marks should be approximately the stem travel shown in chart. STEM TRAVEL (Fully Open to Fully Closed) Valve Size (inches) Travel (inches) Inches MM Inches MM / 32 0. 0 /2 0 0. 0 2 0 0. 2 /2 0.7 3 0 0. 20 00. 2 0.7 3 200 2.3 0 20 2. 7 2 300 3. 30.0 00 00. 2 00. 30 00 7. 90 3 900. 2 0. If the stroke is different than that shown in stem travel chart this is a good reason to believe something is mechanically restricting the stroke of the valve at one end of its travel. If the flow does not stop through the valve when in the indicated closed position, the obstruction probably is between the disc and the seat. If the flow does stop, then the obstruction is more likely in the cover. In either case, the cover must be removed, and the obstruction located and removed. The stem should also be checked for scale buildup. (See Maintenance, section for procedure.). For valves and smaller, the Hytrol Valve s freedom of movement check can also be done after all pressure is removed from the valve. SEE CAUTION. After closing inlet and outlet isolation valves and bleeding pressure from the valve, check that the cover chamber and the body are temporarily vented to atmosphere. Insert fabricated tool into threaded hole in top of valve stem, and lift the diaphragm assembly manually. Note any roughness. The diaphragm assembly should move smoothly throughout entire valve stroke. The tool is fabricated from rod that is threaded on one end to fit valve stem and has a T bar handle of some kind on the other end for easy gripping. (See chart in Step of Disassembly Section.) 2. Place marks on this diaphragm assembly lifting tool when the valve is closed and when manually positioned open. The distance between the two marks should be approximately the stem travel shown in stem travel chart. If the stroke is different than that shown, there is a good reason to believe something is mechanically restricting the stroke of the valve. The cover must be removed, and the obstruction located and removed. The stem should also be checked for scale build-up. (See Maintenance Section for procedure.) Tight Sealing Check (#3) 3. Test for seat leakage after completing checks # & #2 (Steps to 2). SEE CAUTION. Close the isolation valve downstream of the Hytrol Valve. Apply inlet pressure to the cover of the valve, wait until it closes. Install a pressure gauge between the two closed valves using one of the two ports in the outlet side of the Hytrol. Watch the pressure gauge. If the pressure begins to climb, then either the downstream isolation valve is permitting pressure to creep back, or the Hytrol is allowing pressure to go through it. Usually the pressure at the Hytrol inlet will be higher than on the isolation valve discharge, so if the pressure goes up to the inlet pressure, you can be sure the Hytrol is leaking. Install another gauge downstream of isolating valve. If the pressure between the valves only goes up to the pressure on the isolation valve discharge, the Hytrol Valve is holding tight, and it was just the isolation valve leaking. 3
Maintenance Preventative Maintenance The Cla-Val Co. Model 00-0 Hytrol Valve requires no lubrication or packing and a minimum of maintenance. However, a periodic inspection schedule should be established to determine how the operating conditions of the system are affecting the valve. The effect of these actions must be determined by inspection. Disassembly Inspection or maintenance can be accomplished without removing the valve from the line. Repair kits with new diaphragm and disc are recommended to be on hand before work begins. WARNING: Maintenance personnel can be injured and equipment damaged if disassembly is attempted with pressure in the valve. SEE CAUTION.. Close upstream and downstream isolation valves and independent operating pressure when used to shut off all pressure to the valve. 2. Loosen tube fittings in the pilot system to remove pressure from valve body and cover chamber. After pressure has been released from the valve, use care to remove the controls and tubing. Note and sketch position of tubing and controls for re-assembly. The schematic in front of the Technical Manual can be used as a guide when reassembling pilot system. 3. Remove cover nuts and remove cover. If the valve has been in service for any length of time, chances are the cover will have to be loosened by driving upward along the edge of the cover with a dull cold chisel. VALVE STEM THREAD SIZE Valve Size Thread Size (UNF Internal) /" 2 /2" 0 32 3" " / 2 " " 3/ 2 " /2 20 2" 3/- 30 3/- 3 3/-. The next item to remove is the stem nut. Examine the stem threads above the nut for signs of mineral deposits or corrosion. If the threads are not clean, use a wire brush to remove as much of the residue as possible. Attach a good fitting wrench to the nut and give it a sharp rap rather than a steady pull. Usually several blows are sufficient to loosen the nut for further removal. On the smaller valves, the entire diaphragm assembly can be held by the stem in a vise equipped with soft brass jaws before removing the stem nut. The use of a pipe wrench or a vise without soft brass jaws scars the fine finish on the stem. No amount of careful dressing can restore the stem to its original condition. Damage to the finish of the stem can cause the stem to bind in the bearings and the valve will not open or close.. After the stem nut has been removed, the diaphragm assembly breaks down into its component parts. Removal of the disc from the disc retainer can be a problem if the valve has been in service for a long time. Using two screwdrivers inserted along the outside edge of the disc usually will accomplish its removal. Care should be taken to preserve the spacer washers in water, particularly if no new ones are available for re-assembly. 7. The only part left in the valve body is the seat which ordinarily does not require removal. Careful cleaning and polishing of inside and outside surfaces with 00 wet/dry sandpaper will usually restore the seat s sharp edge. If, however, it is badly worn and replacement is necessary, it can be easily removed. On and smaller valves block and tackle or a power hoist can be used to lift valve cover by inserting proper size eye bolt in place of the center cover plug. on and larger valves there are holes (/ size) where jacking screws and/or eye bolts may be inserted for lifting purposes. Pull cover straight up to keep from damaging the integral seat bearing and stem. COVER CENTER PLUG SIZE Valve Size Thread Size (NPT) /" /2" /" 2" 3" /2" " " 3/" " 0" " 2" /" " /2" " 2" 2" 2" 30 & 3 2. Remove the diaphragm and disc assembly from the valve body. With smaller valves this can be accomplished by hand by pulling straight up on the stem so as not to damage the seat bearing. On large valves, an eye bolt of proper size can be installed in the stem and the diaphragm assembly can be then lifted with a block and tackle or power hoist. Take care not to damage the stem or bearings. The valve won't work if these are damaged. Seats in valve sizes / through are threaded into the valve body. They can be removed with accessory X09 Seat Removing Tool available from the factory. On and larger valves, the seat is held in place by flat head machine screws. Use a tight-fitting, long shank screwdriver to prevent damage to seat screws. If upon removal of the screws the seat cannot be lifted out, it will be necessary to use a piece of angle or channel iron with a hole drilled in the center. Place it across the body so a long stud can be inserted through the center hole in the seat and the hole in the angle iron. By tightening the nut a uniform upward force is exerted on the seat for removal. NOTE: Do not lift up on the end of the angle iron as this may force the integral bearing out of alignment, causing the stem to bind. DO NOT LIFT VALVE SEAT VALVE BODY NUT ANGLE OR CHANNEL IRON LONG STUD OR BOLT NUT OR BOLT HEAD
Lime Deposits One of the easiest ways to remove lime deposits from the valve stem or other metal parts is to dip them in a -percent muriatic acid solution just long enough for the deposit to dissolve. This will remove most of the common types of deposits. CAUTlON: USE EXTREME CARE WHEN HANDLING ACID. Rinse parts in water before handling. If the deposit is not removed by acid, then a fine grit (00) wet or dry sandpaper can be used with water. Inspection of Parts After the valve has been disassembled, each part should be examined carefully for signs of wear, corrosion, or any other abnormal condition. Usually, it is a good idea to replace the rubber parts (diaphragm and disc) unless they are free of signs of wear. These are available in a repair kit. Any other parts which appear doubtful should be replaced. WHEN ORDERlNG PARTS, BE SURE TO GIVE COMPLETE NAMEPLATE DATA, ITEM NUMBER AND DESCRlPTlON. NOTE: If a new disc isn t available, the existing disc can be turned over, exposing the unused surface for contact with the seat. The disc should be replaced as soon as practical. Reassembly. Reassembly is the reverse of the disassembly procedure. If a new disc has been installed, it may require a different number of spacer washers to obtain the right amount of grip on the disc. When the diaphragm assembly has been tightened to a point where the diaphragm cannot be twisted, the disc should be compressed very slightly by the disc guide. Excessive compression should be avoided. Use just enough spacer washers to hold the disc firmly without noticeable compression. 2. MAKE SURE THE STEM NUT IS VERY TIGHT. Attach a good fitting wrench to the nut and give it a sharp rap rather than a steady pull. Usually several blows are sufficient to tighten the stem nut for final tightening. Failure to do so could allow the diaphragm to pull loose and tear when subjected to pressure. 3. Carefully install the diaphragm assembly by lowering the stem through the seat bearing. Take care not to damage the stem or bearing. Line up the diaphragm holes with the stud or bolt holes on the body. on larger valves with studs, it may be necessary to hold the diaphragm assembly up part way while putting the diaphragm over the studs.. Put spring in place and replace cover. Make sure diaphragm is Iying smooth under the cover.. Tighten cover nuts firmly using a cross-over pattern until all nuts are tight.. Test Hytrol Valve before re-installing pilot valve system. Test Procedure After Valve Assembly There are a few simple tests which can be made in the field to make sure the Hytrol Valve has been assembled properly. Do these before installing pilot system and returning valve to service. These are similar to the three troubleshooting tests.. Check the diaphragm assembly for freedom of movement after all pressure is removed from the valve. SEE CAUTlON. Insert fabricated tool into threaded hole in top of valve stem, and lift the diaphragm assembly manually. Note any roughness, sticking or grabbing. The diaphragm assembly should move smoothly throughout entire valve stroke. The tool is fabricated from rod that is threaded on one end to fit valve stem (See chart in Step of Disassembly section.) and has a T Bar handle of some kind on the other end for easy gripping. Place marks on this diaphragm assembly lifting tool when the valve is closed and when manually positioned open. The distance between the two marks should be approximately the stem travel shown in stem travel chart. (See Freedom of Movement Check section.) If the stroke is different than that shown, there is a good reason to believe something is mechanically restricting the stroke of the valve. The cover must be removed, the obstruction located and removed. (See Maintenance Section for procedure.) Due to the weight of the diaphragm assembly this procedure is not possible on valves and larger. on these valves, the same determination can be made by carefully introducing a low pressure-less than five psi) into the valve body with the cover vented. SEE CAUTION. Looking in cover center hole see the diaphragm assembly lift easily without hesitation, and then settle back easily when the pressure is removed. 2. To check the valve for drip-tight closure, a line should be connected from the inlet to the cover, and pressure applied at the inlet of the valve. If properly assembled, the valve should hold tight with as low as ten PSI at the inlet. See Tight Sealing Check section.) 3. With the line connected from the inlet to the cover, apply full working pressure to the inlet. Check all around the cover for any leaks. Re-tighten cover nuts if necessary to stop leaks past the diaphragm.. Remove pressure, then re-install the pilot system and tubing exactly as it was prior to removal. Bleed air from all high points.. Follow steps under Start-Up and Adjustment Section in Technical Manual for returning complete valve back to service.
2 2 2 0 7 7 9 3 INLET OUTLET TOP VIEW PARTS LIST Item Description. Pipe Plug 2. Drive Screws (for nameplate) 3. Hex Nut ( and larger). Stud ( and larger). Cover Bearing. Cover 7. Stem Nut. Diaphragm Washer 9. Diaphragm 0. Spacer Washers. Disc Guide 2. Disc Retainer 3. Disc. Stem. Seat. Body 7. Spring 22. Flat Head Screws ( and larger) 23. Seat O-Ring 2. Hex head Bolt ( / thru ) 2. Nameplate 2. Upper Spring Washer (Epoxy coated valves only) 27. Lower Spring Washer (Epoxy coated valves only) 2. Cover Bearing Housing ( only) 29. Cover O-Ring ( only) 30. Hex Bolt ( only) 3. Pipe Cap ( only) 27 2 GLOBE PATTERN 2 INLET ANGLE PATTERN 9 3 OUTLET 3 2 2 0 3 23 22 30 23 29 /" - " SEAT DETAIL " - 2" SEAT DETAIL " COVER DETAIL
Description 00-0 Hytrol Valve The CIa-VaI Model 00-0 Hytrol Valve is a main valve for CIa-VaI Automatic Control Valves. It is a hydraulically operated, diaphragm-actuated, globe or angle pattern valve. This valve consists of three major components; body, diaphragm assembly, and cover. The diaphragm assembly is the only moving part. The diaphragm assembly uses a diaphragm of nylon fabric bonded with synthetic rubber. A synthetic rubber disc, contained on three and one half sides by a disc retainer and disc guide, forms a seal with the valve seat when pressure is applied above the diaphragm. The diaphragm assembly forms a sealed chamber in the upper portion of the valve, separating operating pressure from line pressure. INSTALLATION / OPERATION / MAINTENANCE MODEL 00-0 Hytrol Valve Service Data Description 00-20 00 Series Hytrol Valve The CIa-VaI Model 00-20 Hytrol Valve (00 Series main valve) have only one part -the body- that is different from standard 00 Series Cla-Val main valve parts. The remaining parts of the 00 series main valve are standard Cla-Val main valve parts. All service and maintenance information for the standard 00 Series main valves also apply to the 00 series main valves. The most important thing to remember when ordering main valve repair kits and replacement parts, except for the body, all other parts are going to be for a smaller size main valve. Cla- Val identifies main valve parts with the flange size of the standard 00 Series main valve. Refer to the "Main Valve Sizes chart below. HYTROL Service Data HYTROL SIZE Stem Cover Capacity Valve Stem Cover Cover Nut or Bolt Cover Cover Plug Cover Torque Stem Nut ** Stem Nut Torque 00-0 00-20 Travel Displacement Thread Center Thread Socket Qty Lifting (ft Lbs) UNF-Internal Plug NPT (Bolt) Holes UNC Thread Socket ft. Lbs. in. Lbs. Thread Socket inches mm inches mm inches mm Gallons Liters (Long) Lubed DRY / /2 2 32 0 0.3 0. 0. 0 0 0.020 0.020 0.07 0.07 0-32 0-32 / / / / - 20 (B) / - (B) / - (B) 7/ /2 /2 9 9 3/ - 2 7/ 20 7/ 20 0 0 2 2 /2 3 0 2 2 0 0 00 0 200 20 300 30 00 00 0 2 20,2 00 0 200 20 300 00 00 0. 0.7 0...7 2.3 2. 3. 3.9.. 20 23 3 7 99 0.032 0.03 0.00 0.9 0.3.2 2..0. 9. 29.0 0.2 0. 0.30 0. 2.00.0 9.0.0 2.0 3.20 0.0 0-32 0-32 / - 2 / - 2 3/ - 2 3/ - 2 3/ - 2 3/ - 2 3/ - 2 /2-20 3/ - * /2 /2 /2 3/ 3/ / /2 2 3/ 3/ - (B) 7/ - (B) /2-3 (B) 3/ - 0 (B) 3/ - 0 (B) 3/ - 0 7/ - 9 -/ -7 -/ -7 -/ -7 -/2-2 9/ / 3/ / / / 7/ 3/ 2 2 2 3/ 2 20 20 20 20 2 / - 3/ - 0 3/ - 0 - - -/ 7 3/ /2 /2 3/ 3/ 7/ 9/ 9/ / / 3/ 3/ 3/ 3/ 3/ 3/ 2 20 30 0 0 0 0 390 00 /2-20 / - / - 3/ - 7/ - / - 2 /2-2 /2-2 /2-2 2-3 - 2 3/ / / / / 3/ 7/ 2 /2 2 /2 3 Special 0 2 2 0 2 20 270 20 00 30 30 30 0 2 37 00 20 70 N/R * Adapter p/n 290E inside / - 2 Grade Bolts Heavy Grade Nuts Tighten cover nuts in a star cross-over pattern **Must Use ONLY Cla-Val Supplied part
00-0 Hytrol Main Valve Assembly COVER Cover Bolt " and Smaller SPRING PIPE PLUG COVER BEARING HEX NUT " and Larger PIPE PLUG BOLT/NUT TORQUING PROCEDURES ON VALVE COVERS BOLTS 3 BOLTS 3 BOLTS 3 7 STEM NUT DIAPHRAGM WASHER 2 2 2 KO Anti-Cavitation Trim Option KO DISC GUIDE *DIAPHRAGM *DISC DISC GUIDE DISC RETAINER *SPACER WASHERS STEM 0 2 2 BOLTS 2 7 3 9 2 BOLTS Follow this procedure when reassembling MAIN Valve: 0 9 2 3 7 3 2 20 7 0 20 BOLTS 2 9 7 3 3 9 KO SEAT SEAT Seat Screw " and Larger. Tightens bolts/nuts in a Star or Cross-Over Pattern following the numbers shown above to insure that cover seats evenly on the diaphragm material and body. SEAT O-RING STUD 2. Torque the bolt/nuts in three stages: BODY (Globe or Angle) " and Larger PIPE PLUG *Repair Parts A. To approximately 0% of final torque valve. B. To approximately 7% of final torque valve. C. To final required torque valve. 3. Valves that are to be tested to 37 PSI or higher should be retorqued after 2 hours. N-00-0 (R-2/07)
INSTALLATION / OPERATION / MAINTENANCE MODEL 00-20 (Reduced Internal Port) 00 Series Hytrol Valve SERVICE AND MAINTENANCE OF 00 SERIES VALVES The 00 series main valves have only one part -the body- that is different from standard 00 Series Cla-Val main valve parts. The remaining parts of the 00 series main valve are standard Cla- Val main valve parts. All service and maintenance information for the standard 00 Series main valves in this manual also apply to the 00 series main valves. The most important thing to remember when ordering main valve repair kits and replacement parts, except for the body, all other parts are going to be for a smaller size main valve. Cla-Val identifies main valve parts with the flange size of the standard 00 Series main valve. Refer to the "Main Valve Sizes Comparison" chart. For example, if you are servicing a " 00-20 Hytrol and needed a repair kit, you would order a repair kit for a " 00-0 Hytrol. This kit is also suitable for a " 00-20 Hytrol. Complete Technical Manuals include a repair kit data sheet N-RK that shows this relationship. When you order repair parts, it is a good idea to include valve nameplate data (size, catalog number, and part number) and description of the parts desired. Do this to be sure parts will fit the valve you are working on and not be too big for it. Pilot controls and repair kits maintenance information remain the same for 00 or 00 Series valves. UNDERSTANDING THE 00 SERIES VALVES In 97, Cla-Val introduced the Model 00-20 Hytrol as the basic main valve for the 00 Series of automatic control valves. To identify all new valves using the 00-20 Hytrol, an existing catalog number is modified. Making a 00 Series catalog number is simply done by using a "" in front of the two digit catalog numbers or replacing the "2" with a "" in three digit catalog numbers. Current schematics reflect both catalog numbers together separated by a slash ( i.e. - 90-0/90-0, -02/-02, 20-0/0-0, etc). Since these two valves 'share' the same catalog number and schematic, they provide the same function in a system. The only difference between the two valves is the relative capacity of the two main valve series. The 00-0 Hytrol is the basic main valve for Cla-Val automatic control valves. This valve is the current version of the Clayton Hytrol valve design originated in 93. The 00-0 Hytrol is designed as a full flow area valve. This means that the inlet, seat and outlet openings are the same size. Thus, the pressure drop is kept to a minimum for this globe style design. The 00-20 Hytrol valve has all of the basic features and advantages of the original 00-0 Hytrol. Only one part has been changed - the body. It is designed with different size inlet, seat and outlet openings. The 00-20 Hytrol has inlet and outlet flanges one valve size larger than the seat opening size. This results in what is sometimes called a ''reduced port' main valve. For example, a " 00-20 valve has a 3" seat. Note: valve size is always determined by the flange size. The following chart compares the 00-0 and the 00-20 main valves. Basic Main Valve Size Comparison Globe Pattern Valves Flange Size (inch) Seat Size 00-0 (00 Series) 00-20 (00 Series) 3 3 2 3 0 0 2 2 0 ---- 2 20 ---- 2 2 30 30 2 3 3 30 2 ---- 3 ---- 3 Angle Pattern Valves Flange Size (inch) Seat Size 00-0 (00 Series) 00-20 (00 Series) 3 The 00-20 Hytrol is available only in ductile iron, 0 and 300 pressure class, and Bronze trim standard. Available extra cost main valve options include stainless steel trim, epoxy coating, Dura-Kleen stem, Delrin sleeved stem, and high temperature rubber parts. All four basic main valves have a 00 Series version available with all of the same benefits and size relationships. The following chart shows the relationship of Cla-Val main valve catalog numbers. Catalog Name Hytrol Powertrol Powercheck Hycheck Cla-Val Main Valves Catalog Number Circa 93 00-Series 00 (Angle =200) 00-0 00P & 00PA 00-02 00PC & 00PCA 00-03 00-0 00 Series 00-20 00-2 00-22 00-23
00-20 PARTS LIST NO. DESCRIPTION Pipe Plug 2 2 GLOBE INLET 2 3 TOP VIEW 9 2 3 OUTLET 2 Drive Screws (for nameplate) 3 Hex Nut (" and larger) Stud (" and larger) Cover Bearing Cover 7 Stem Nut Diaphragm Washer 9 Diaphragm 0 Spacer Washers Disc Guide 2 Disc Retainer 3 Disc Stem Seat Body 7 Spring 22 Flat Head Screws (0" and larger) 23 Seat O-Ring 2 Hex Bolt (3 " Thru ") 2 Nameplate (Mounted on inlet flange) 2 Upper Spring Washer (Epoxy coated valves only) 27 Lower Spring Washer (Epoxy coated valves only) 2 Cover Bearing Housing (20" & 2" & 30") 29 Cover Bearing Housing O-Ring (20"& 2" & 30") 30 Hex Bolt (20" & 2") 3 Pipe Cap (20" & 2 & 30"") ANGLE INLET WHEN ORDERING PARTS, BE SURE TO GIVE COMPLETE NAMEPLATE DATA, ITEM NUMBER AND DESCRIPTION. 27 2 7 7 9 0 3 22 3 2 30 29 3" " COVER DETAIL 2 23 0" 2" SEAT DETAIL 20" 2" COVER DETAIL N-00-20 (R-/0)
XA Strainer and Orifice Assembly BRONZE BODY S.S. ORIFICE 3/" x 3/" PARTS LIST XA STOCK NO. ORIFICE DIA. ORIFICE PLUG PART # (ITEM ) 3/ 3/ / NPT 3/ NPT 730-0 -02-03 -0-0 -0 * -07-0 -09-0 *Standard.03.0.02.07.093.09.2.0..7 932-0 -02-03 -0-0 -0-07 -0-09 -0 3 3/ 2 3 When ordering parts, please specify: 7/ 3/ NPT All Nameplate Data Item Number Description Recommended Spare Parts Inlet Outlet 2 / MAX. 7 ITEM DESCRIPTION MATERIAL QTY. Body Red Brs. 2 Plug, Top Brass 3 "O" Ring, Plug Top Syn. Rub. Screen Monel Orifice Plug Delrin Plug, Pipe Brass 7 Strainer Plug S.S. "O" Ring, Strainer Plug Syn. Rub. P-XA (R-/0)
INSTALLATION / OPERATION / MAINTENANCE MODEL CV Flow Control DISASSEMBLY Follow the sequence of the item numbers assigned to the parts in the cross sectional illustration for recommended order of disassembly. Use a scriber, or similar sharp-pointed tool to remove O-ring from the stem. INSPECTION Inspect all threads for damage or evidence of crossthreading. Check mating surface of seat and valve disc for excessive scoring or embedded foreign particles. Check spring for visible distortion, cracks and breaks. Inspect all parts for damage, corrosion and cleanliness. DESCRIPTION The Cla-Val Model CV Flow Control is a simply-designed, spring-loaded check valve. Rate of flow is full flow in one direction and restricted in other direction. Flow is adjustable in the restricted direction. It is intended for use in conjunction with a pilot control system on a Cla-Val Automatic Control Valve. OPERATION The CV Flow Control permits full flow from port A to B, and restricted flow in the reverse direction. Flow from port A to B lifts the disc from seat, permitting full flow. Flow in the reverse direction seats the disc, causing fluid to pass through the clearance between the stem and the disc. This clearance can be increased, thereby increasing the restricted flow, by screwing the stem out, or counter-clockwise. Turning the stem in, or clockwise reduces the clearance between the stem and the disc, thereby reducing the restricted flow. INSTALLATION Install the CV Flow Control as shown in the valve schematic All connections must be tight to prevent leakage. CLEANING After disassembly and inspection, cleaning of the parts can begin. Water service usually will produce mineral or lime deposits on metal parts in contact with water. These deposits can be cleaned by dipping the parts in a -percent muriatic acid solution just long enough for deposits to dissolve. This will remove most of the common types of deposits. Caution: use extreme care when handling acid. If the deposit is not removed by acid, then a fine grit (00) wet or dry sandpaper can be used with water. Rinse parts in water before handling. An appropriate solvent can clean parts used in fueling service. Dry with compressed air or a clean, lint-free cloth. Protect from damage and dust until reassembled. REPAIR AND REPLACEMENT Minor nicks and scratches may be polished out using a fine grade of emery or crocus cloth; replace parts if scratches cannot be removed. Replace O-ring packing and gasket each time CV Flow Control is overhauled. Replace all parts which are defective. Replace any parts which create the slightest doubt that they will not afford completely satisfactory operation. Use Inspection steps as a guide. REASSEMBLY Reassembly is the reverse of disassembly; no special tools are required. TEST PROCEDURE No testing of the flow Control is required prior to reassembly to the pilot control system on Cla-Val Main Valve. N-CV (R-/0)
PARTS LIST CV 3/" Flow Control 2.2 MAX ADJUSTING STEM (TURN CLOCKWISE TO INCREASE RESTRICTION) STAMP PART NO. ON SMOOTH SURFACE RESTRICTED FLOW 7 2 0 9. 3/ - NPT 3. FREE FLOW When ordering parts, please specify: Number Stamped on Side Description (CV Flow Control) Part Description Material ITEM DESCRIPTION QTY Cap (SS only) 2 Nut, Jam 3 Seat Gasket Disc Spring 7 Ring, Retaining BAR STOCK CONFIGURATION Stem 9 O-Ring 0 Housing PL-CV (R-/0)
MODEL X0 Valve Position Indicator & Pilot System Components Positive Visual Indicator Frictionless Leak Proof Easy Maintenance and Cleaning Protected Indicator Rod The Cla-Val Model X0 Visual Position Indicator is designed to display Cla-Val valve position quickly and easily. A solid brass indicator rod fastened directly to the valve stem moves up and down inside a pyrex tube. The tube is contained within a brass housing which is open on two opposite sides to permit clear vision of the indicator rod. To purge air that may be trapped in the valve cover, a vent valve in the top of the housing is provided. Model X0 valve position indicator is furnished complete for installation on specified size Cla-Val Automatic Control Valve. Dimensions Specifications Vent Valve Sizes: " thru 2" Materials: Brass, Pyrex Tube Gasket VALVE A B SIZE INCHES NPT ". /" Pressure Rating: Optional Material: 00 psi Stainless Steel Housing /" 3.2 /" A Vent Valve Closed Sight Tube Gasket Adapter Bushing /2" 3.2 /" 2" 3.33 /2" 2 /2" 3.33 /2" 3" 3.33 /2" ".2 3 " ".2 3 " ".3 " Installation Can be installed on any Cla-Val basic main valve in a few minutes. Simply replace the fitting on top of the valve cover with the indicator assembly. B NPT Valve Cover 0" 7.70 " 2".20 /" ".20 /2" When Ordering, Please Specify. Valve Size Stem Stem Adapter " 0. 2" 2" 2.0 " 2. Catalog No. X0 3. Valve Series No. (Appears on Valve Nameplate) Valve Stem. Optional Material Stainless Steel Dimension "A" is height added to valve by indicator assembly
CSM- Solenoid Control CDS Altitude Control Standard: Body Material Bronze with Monel Trim Wetted Body Material Standard: Bronze with Stainless Steel Trim Option: Bronze with Stainless Steel Trim No. of Springs Altitude Ranges - 0 ft 2 30-0 ft 3 70-20 ft 0-0 ft 0-200 ft CDC- Check Valve CSC Swing Check Valve Size Body Material Trim Material 3/"-/2" Brass Delrin Size Body Material Trim Material 3/"-" Brass Brass/Buna N CN Series - Needle Valves CK Series - Isolation Valve Size Body Material Trim Material /"-" Standard: Bronze Brass Option: Stainless Steel Stainless Steel Size Body Material Trim Material 3/"-" Standard: Bronze Stainless Steel/Teflon Option: Stainless Steel Stainless Steel/Teflon Distributed By: M&M Control Service, Inc. Phone: 00-7-003 Fax: 7-3-077 Email: sales@mmcontrol.com Represented By:
X0 Valve Position Indicator COMPLETE X0 SIZE STOCK NO. / - /2 C22A 2 C972G 2 /2 C207E 3 C209A 97000A 970002J CF 0 C97A 2 320D 302C 302D PARTS LIST ITEM DESCRIPTION MATERIAL Vent Valve Brass 2 Housing Brass 3 *Gasket (2 Required) Buna-N *Sight Tube Pyrex Adapter Brass Busing Brass 7 Stem Brass Stem Adapter Brass When ordering parts, please specify: All Nameplate data Item Number Description Material Part Number
Cla-Val Product Identification How to Order Proper Identification For ordering repair kits, replacement parts, or for inquiries concerning valve operation, it is important to properly identify Cla-Val products already in service by including all nameplate data with your inquiry. Pertinent product data includes valve function, size, material, pressure rating, end details, type of pilot controls used and control adjustment ranges. Identification Plates For product identification, cast-in body markings are supplemented by identification plates as illustrated on this page. The plates, depending on type and size of product, are mounted in the most practical position. It is extremely important that these identification plates are not painted over, removed, or in any other way rendered illegible. INLET EINTRITT ENTREE ENTRADA SIZE & CAT NO. STOCK NO. CODE MFD. BY CLA-VAL NEWPORT BEACH, CALIF, U.S.A. This brass plate appears on valves sized 2 / 2" and larger and is located on the top of the inlet flange. INLET INLET These two brass plates appear on 3 / ", / 2", and 3 / " size valves and are located on the valve cover. RESERVOIR END This brass plate appears on altitude valves only and is found on top of the outlet flange. SIZE & CAT NO. STOCK NO. FLOW MFD. BY CLA-VAL NEWPORT BEACH, CALIF. U.S.A. CODE These two brass plates appear on threaded valves " through 3" size or flanged valves " through 2". It is located on only one side of the valve body. SPRING RANGE C SIZE & CAT NO. STOCK NO. SIZE & CAT NO. STOCK NO. CODE MFD. BY CLA-VAL NEWPORT BEACH, CALIF. U.S.A. MFD. BY CLA-VAL NEWPORT BEACH, CALIF. U.S.A. This tag is affixed to the cover of the pilot control valve. The adjustment range appears in the spring range section. This brass plate is used to identify pilot control valves. The adjustment range is stamped into the plate. C DO NOT REMOVE THIS VALVE HAS BEEN MODIFIED SINCE ORIGINAL SHIPMENT FROM FACTORY. WHEN ORDERING PARTS AND/ OR SERVICE SUPPLY DATA FROM THIS PLATE & ALL OTHER PLATES ON ORIGINAL VALVE. This aluminum plate is included in pilot system modification kits and is to be wired to the new pilot control system after installation. CAT. NO.RP - REDUCED PRESSURE BACKFLOW PREVENTION DEVICE STK. NO. SER. NO. CLA-VAL NEWPORT BEACH, CA. This brass plate is used on our backflow prevention assemblies. It is located on the side of the Number Two check (2" through 0"). The serial number of the assembly is also stamped on the top of the inlet flange of the Number One check.
HOW TO ORDER Distributed By: M&M Control Service, Inc. Phone: 00-7-003 Fax: 7-3-077 Email: sales@mmcontrol.com SPECIFY WHEN ORDERING Model Number Valve Size Globe or Angle Pattern Threaded or Flanged Adjustment Range Body and Trim Materials (As Applicable) Optional Features Pressure Class UNLESS OTHERWISE SPECIFIED Globe or angle pattern are the same price Ductile iron body and bronze trim are standard X Flow Clean Strainer or X3 Y Strainer are included CK2 Isolation Valves are included in price on " and larger valve sizes (" and larger on 00 Series) NOTES: NOTES: Distributed By: M&M Control Service, Inc. Phone: 00-7-003 Fax: 7-3-077 Email: sales@mmcontrol.com Represented By:
INSTALLATION / OPERATION / MAINTENANCE MODEL REPAIR KITS Complete Replacement Diaphragm Assemblies for 00-0 and 00-20 Hytrol Main Valves For: Hytrol Main Valves with Ductile Iron, Bronze Trim Materials 2/0 Pressure Class Only. FACTORY ASSEMBLED Includes: Stem, Disc Guide, Disc, Disc Retainer, Spacer Washers, Diaphragm, Diaphragm Washer and Stem Nut. Valve Size Diaphragm Assembly Stock Number 00-0 00-20 Valve Size Diaphragm Assembly Stock Number 00-0 00-20 3/" /2" - 3/" " /"- /2" 2" 2 /2" 3" " (Also -0 ) (Also -0 ) 9097K C2D C220K C222 F C22B C223D C22J 33273E C22B C22J " " 0" 2" " " 20" 2" 0G 27D 72J 33J 907D 90B 33273E 0G 27D 72J 33J 90B 90B Repair Kits for 00-0/00-20 Hytrol Valves For: Hytrol Main Valves 2/0 Pressure Class Only. Includes: Diaphragm, Disc (or Disc Assembly) and spare Spacer Washers. Valve Size 3/" /2" - 3/" " /" - /2" 2" 2 /2" 3" " " " 0" 2" " " 20" 2" Buna-N Standard Material Repair Kit Stock Number (Also -0 ) (Also -0 ) 00-0 00-20 990K 9902H 9903F 990D 990A 99J 992G 993E 99K 9790D 97902B 97903K 9790H 9790E 9790C 990A 992G 993E 99K 9790D 97902B 97903K 9790E 9790E Valve Size 3/" /2" - 3/" " / - /2" 2" 2 /2" 3" " " " Viton (For KB Valves) Repair Kit Stock Number (Also -0 ) (Also -0 ) 00-0 00-20 990J 9907G 990E 9909C 990A 997F 99D 999B 9920K 993A 990A 99D 999B 9920K When ordering, please give complete nameplate data of the valve and/or control being repaired. MINIMUM ORDER CHARGE APPLIES.
Repair Kits for 00-02/00-2 Powertrol and 00-03/00-22 Powercheck Main Valves For: Powertrol and Powercheck Main Valves 2/0 Pressure Class Only Includes: Diaphragm, Disc (or Disc Assembly) and O-rings and full set of spare Spacer Washers. Valve Kit Stock Number Valve Kit Stock Number Size 00-02 Size 00-02 & 00-03 00-2 & 00-22 3 9990H 2 2 9990J 2 & 3 99902F 3 999G 9990J 99903D 9992E 999G & 2 9990B 9993C 9992E 2 9990J 99G 9993C 0 99939H 99G 2" 99937B 99939H Repair Kits for 00-0/00-23 Hy-Check Main Valves For: Hy-Check Main Valves 2/0 Pressure Class Only Larger Sizes: Consult Factory. Includes: Diaphragm, Disc and O-Rings and full set of spare Spacer Washers. Valve Kit Stock Number Valve Kit Stock Number Size 00-0 00-23 Size 00-0 00-23 202090B 2 202090H 202090J 2020902A 202090B 202090G 2020903K 2020902A 2020907F 202090H 0 202090J 2020903K 20 2020907F 2 2020907F Repair Kits for Pilot Control Valves Includes: Diaphragm, Disc (or Disc Assembly), O-Rings, Gaskets or spare Screws as appropriate. BUNA-N (Standard Material) VITON (For KB Control) Pilot Control Kit Stock Number Pilot Control Kit Stock Number Pilot Control Larger Sizes: Consult Factory. Repair Assemblies (In Standard Materials Only) Control Description Stock Number CF-C Pilot Assembly Only 9H CF-Cl Complete Float Control less Ball and Rod 90A CFC2-C Disc, Distributor and Seals 2770E CSM -A2-2 Mechanical Parts Assembly 97B CSM -A2-2 Pilot Assembly Only 03K 33A " Complete Internal Assembly and Seal 203030B 33A 2" Complete Internal Assembly and Seal 20030J Kit Stock Number CDB 97000C CRM-7 2390K CDB-KB 97002A CDB-3D 970023H CFM-7A 2390K CRA-KB CDB-3I 97002F CFM-9 2223E CRD-KB (w/bucking spring) 97000J CDB-7 97007K CRA (w/bucking spring) 97000D CRL-KB 97003J CDH-2 22D CRD (w/bucking spring) 970002B CDHS-2BKB 97000E CDHS-2 07A CRD (no bucking spring) 970003K CDHS-2FKB 9700C CDHS-2B 97000H CRD- 20270K CDHS-KB (no bucking spring) 970009G CDHS-2F 97000E CRD-22 9923G 02C-KB 72202D CDHS-3C-A2 27K CRL (F, L) 970007A CDHS-A 290A CRL-A 33E CDHS- 970003K CRL- (B) 7B CDS- 9700G CRL-A (G) 20E CDS- 200A CRL- 203090C CDS- 20930A CV 97009F CDS-A 20390C X0L (O-ring) 009E Buna-N CFCM-M 22230C 02B- 0220F CRD Disc Ret. (Solid) C2H CFM-2 2223E 02C-2 720F CRD Disc Ret. (Spring) C2K 02C-3 720F When ordering, please give complete nameplate data of the valve and/or control being repaired. MINIMUM ORDER CHARGE APPLIES