data features 9 mton (00 ton) capacity 07 mton-m (,4 ft-kips) Maximum oad Moment 6,0 m (00') eavy-ift 76, m (50') Fixed Jib on eavy-ift 80,8 m (65') uffing Jib on eavy-ift 96,0 m (5') Fixed Jib on uffing Jib on eavy-ift 7 kw (0 P) engine standard 6 kw (50 P) engine EX & D EPIC controls 74 m/min (570 fpm) line speed Fast, efficient self-assembly 89 kn (0,000 lb) line pull standard 78 kn (40,000 lb) line pull EX & D 8 000 kg (7,600 lb) Clamshell capacity 600 kg (0,000 lb) Clamshell capacity D 8 60 kg (8,000 lb) Dragline capacity Complete crane, maximum boom, fixed jib and counterweight ships on only trucks Manitowoc CraneCARESM product guide contents Specifications Outline Dimensions 6 Transport Data Crane Assembly Performance Data 4 Combinations 8 eavy-ift Range Diagram 0 eavy-ift oad Charts eavy-duty (D) Range Diagram eavy-duty (D) oad Charts Fixed Jib Range Diagram 4 Fixed Jib oad Charts 5 uffing Jib Range Diagram 9 uffing Jib oad Charts 0 Fixed Jib on uffing Jib Range Diagram Fixed Jib on uffing Jib oad Charts CraneCARE SM 4
specifications Upperworks Engine : Cummins 6 CTA 8.C diesel, 6 cylinder, 7 kw (0 BP) @ 00 governed RPM. One volt maintenance-free, Group 8D battery, 400 CCA at -8 C (0 F), volt starting and 80 amp alternator. EX & D: Cummins M diesel, 6 cylinder, 6 kw (50 BP) @ 00 governed RPM. Two volt maintenance-free, Group 8D batteries, 400 CCA at -8 C (0 F), volt starting and 00 amp alternator. Optional additional pad for mounting of accessory hydraulic pumps on Cummins M only. Manually operated disconnect clutch for cold weather starting. Multiple hydraulic pump drive transmission provides independent power for all machine functions. Optional: consult factory for other available engines. One 40 l (90 gal) capacity diesel fuel tank, mounted on rear of upperworks, with level indicator in operator s cab. Controls Modulating electronic-over-hydraulic controls provide infinite speed response directly proportional to control lever movement. Controls include Manitowoc's exclusive EPIC Electronic Processed Independent Controls system providing microprocessor driven control logic, pump control, on-board diagnostics, and service information. Block-up limit control is standard for hoist and whip lines. Integrated oad Moment Indicator system (MI) is standard for main boom, upper boom point, and fixed jib. Function cut-out or warning only operation is available via a keyed switch on the MI console. Optional travel and swing alarms are available. ydraulic System Six high-pressure piston pumps are driven through a multi-hydraulic pump transmission. These six pumps provide independent "closed loop" hydraulic power for front drum, rear drum, boom hoist system, swing system, and both left and right crawler operation. System kg/cm (psi) lpm (gpm) Front Drum 4 (6,000) 84 (75) Rear Drum 4 (6,000) 84 (75) oist 4 (6,000) 55 (4) Swing System 6 (4,500) 55 (4) eft Crawler 4 (6,000) 55 (4) Right Crawler 4 (6,000) 55 (4) ydraulic reservoir capacity is 568 l (50 gal) and is equipped with breather, dipstick, clean out access, and internal diffuser. Each function is equipped with relief valves to protect the hydraulic circuit from overload or shock. Replaceable, spin on ten micron (absolute) full flow line filter is furnished in the hydraulic circuit. All oil is filtered prior to return to the hydraulic reservoir. ydraulic system also includes pump transmission disconnect clutch & hydraulic oil cooler. Optional EX & D only: Open oop ydraulic Power Package consists of: low profile 0 liter (70 gal) hydraulic tank mounted along the top left side of machinery enclosure. Additional hydraulic oil cooler and fan assembly. One main hydraulic pump up to 49 lpm (0 gpm). One pilot hydraulic pump. Ten micron filtration system and machine plumbing. ydraulic manifold with up to five quick-disconnect couplings mounted on the front of the machine. Primary controls and valving. Drums Two equal width winches 54 mm (-/8") wide are driven by independent variable displacement axial piston hydraulic motors through planetary reduction mounted on separate front and rear shafts with anti-friction bearings. Front oist Diameter Max ine Pull, EX 48 mm (9") 89 kn (0,000 lb) D 647 mm (5-/") 78 kn (40,000 lb) Rear oist Diameter Max ine Pull All Models 48 mm (9") 89 kn (0,000 lb) Optional D only: 78 kn (40,000 lb) high pull rear hoist drum can be ordered in place of standard rear 54 mm (-/8") wide 647 mm (5-/") diameter drum. Powered hoisting/lowering and free-fall operation is standard with automatic (spring applied, hydraulically released) multi-disc brakes, clutches, and drum rotation indicators.
specifications Free-fall operation for front and rear drums includes internally expanding clutch assembly and external contracting band brake manually applied by foot pedal with locking latch in operator s cab. Operator may select free-fall or powered lowering mode using a selector switch. Optional auxiliary (third) hydraulic powered drum rated at 66,7 kn (5,000 lb) line pull for third line over upper boom point, or luffing jib intermediate fall, mounted on front of rotating bed. Includes third sheave with boom top wire rope guide and boom butt wire rope guide and third drum control system. Optional auxiliary drum rated at 66,7 kn (5,000 lb) line pull as described above, mounted in boom butt. Optional EX & D only: kn (5,000 lb) third hydraulic drum, for third line over boom point or luffing jib intermediate fall, mounted on front of rotating bed. Includes third sheave with boom top wire rope guide and boom butt wire rope guide and third drum control system. Optional auxiliary drum preparation includes electric wiring and hydraulic plumbing. Optional bolt-on liftcrane laggings. Optional bolt-on clamshell laggings. Optional wire rope for various applications(seepages4-5). oist Independent two-drum boom hoist with grooved drums including, m (40') of 5,88 mm (5/8") diameter wire rope reeved with 0 parts of line. Drums are powered by a fixed displacement hydraulic motor coupled to an internal brake and planetary gearbox equipped with ratcheting pawl. hoist speed: raise 6,0 m (00') full main boom from 0-8 in 80 seconds. Swing System igh strength fabricated steel alloy rotating bed is mounted on,64 m (64-/4") diameter turntable bearing. Reinforced rotating bed for duty cycle operation on the EX & D. Independent swing powered by a fixed displacement hydraulic motor coupled to a planetary gearbox with internal brake. 60 positive swing lock. Swing system maximum speed:.6 rpm. Counterweight Total standard upper counterweight assembly is 4 77 kg (5,000 lb) consisting of one inner 97 kg (8,500 lb) counterweight and one outer 49 kg (4,800 lb) counterweight. During self-assembly, the crane boom butt and hoist are used to lift the counterweights up onto lugs at the rear of the rotating bed upperworks via a tethered remote control. The counterweights are then secured in place by two pins for fast, safe assembly. Optional Series B counterweight system consisting of one 4 56 kg (0,000 lb) middle counterweight box and four crawler frame counterweights at 588 kg (,500 lb) each. Includes connecting pins, brackets, and stops. Operator s Cab Fully enclosed and insulated steel module mounted to the left front corner of rotating bed. Module is equipped with sliding door, large safety glass windows on all sides and roof. Signal horn, cab space heater, front and roof windshield wipers, dome light, sun visor and shade, fire extinguisher and air circulating fan are standard equipment. Optional air conditioning for operator s cab. Optional nylon protective window covers for operator s cab. Attachments No. eavy-ift Main The base & EX liftcranes come standard with a, m (40') No. basic heavy-lift tubular chord boom consisting of a 5,8 m (9') butt and 6,4 m (') open throat top with four 50,8 cm (0") diameter roller bearing sheaves on one shaft. The basic heavy-lift boom also includes a boom angle indicator, pendant rigging, cushioned boom stops, and automatic boom hoist stop. Anti-two block limit controls for main and whip lines. 4,7 m (5' 6") gantry and telescopic backhitch with antifriction bearings and nylon sheaves in gantry and equalizer system. Optional No.,0 m (0'), 6, m (0'), and, m (40') main boom inserts with pendants.
specifications 4 Optional & EX detachable upper boom point with one 50.8 cm (0") roller bearing steel sheave grooved for, mm (7/8") diameter rope with rope guard for lift crane. No. D eavy-duty Main The base D liftcrane comes standard with a, m (40') No. D basic heavy-duty tubular chord boom consisting of 5,8 m (9') butt and 6,4 m (') open throat top with two 86, cm (4") diameter taper roller bearing sheaves on one shaft. The basic heavy-duty boom also includes a boom angle indicator, pendant rigging, cushioned boom stops, and automatic boom hoist stop. Anti-two block limit controls for main and whip lines. 4,7 m (5' 6") gantry and telescopic backhitch with antifriction bearings and nylon sheaves in gantry and equalizer system. Optional No. D,0 m (0') and 6, m (0') main boom inserts with pendants. Note: D utilizes No., m (40') insert(s). Optional D heavy duty detachable upper boom point with one 76, cm (0") roller bearing steel sheave grooved for,75 mm (-/4") diameter rope with rope guard for liftcrane. No. 0 Fixed Jib Optional No. 0 basic fixed jib 9, m (0') length consisting of 4,6 m (5') jib butt and 4,6 m (5') jib top with,7 m (') jib strut, pendants and backstay. Optional No. 0 fixed jib inserts,0 m (0 ). Utilize up to three fixed jib inserts in combination with the No. 0 basic fixed jib for total lengths of, m (40'), 5, m (50'), and 8, m (60'). Optional jib point roller assembly for use on No. 0 fixed jib extension on No. luffing jib. No. 60 for No. uffing Jib Optional 6,8 m (55') basic No. 60 boom for No. luffing jib assembly consisting of: 8,8 m (9') No. 60 transition insert with wire rope guide,, m (7') boom cap assembly, pendants for transition and cap, and pendant spreader. Note: above utilizes existing 5,8 m (9') No. boom butt from base crane. Optional,0 m (0'), 6, m (0'), and, m (40') No. 60 boom inserts with pendants. No. uffing Jib requires No. 60 Main Optional 5, m (50') basic No. luffing jib assembly consisting of: 5,8 m (9') No. luffing jib butt with one 48,9 cm (9-/4") diameter roller bearing sheave (intermediate-fall), 4,8 m (6') fixed strut assembly, 4,8 m (6') jib strut assembly, jib stop assembly, backstay pendants, luffing jib point roller assembly, 5,9 cm (0-7/6") grooved bolt-on lagging for luffing (rear drum), luffing jib hoist line, block up limit, MI (load moment indicator) hardware for intermediate-fall, luffing jib, and fixed jib extension on luffing jib Note: above utilizes existing,0 m (0') No. boom insert and existing 6,4 m (') No. boom top from base crane use existing No. inserts for longer lengths) owerworks Carbody Steel fabricated carbody with wide flange wings for mounting to crawler side frames. Two variable displacement travel motors driven through planetary gearboxes provide narrow-profile mounting within the crawler modules. Crawlers Crawler assemblies are 6,8 m (' 5") long with 9,4 cm (6") wide cast steel crawler pads. Crawlers have full counter-rotation capability. ydraulic extension/retraction of crawler assemblies with tethered remote control. Maximum ground speed of,56 kph (0.97 mph). Optional crawler handling package includes a high capacity wire rope guide mounted on the boom butt, sheave frame that attaches to the boom butt, single sheave 0 mton ( ton) self assembly block for mm (7/8") or mm (-/4") wire rope, and four,8 m (6') nylon eye round slings.
specifications Optional Equipment Optional & EX Blocks and hooks mton ( ton) Swivel hook with 6 kg (740 lb) weight ball mton ( ton) Non-swivel hook with 6 kg (740 lb) weight ball 7 mton (0 ton) hook block with two 50,8 cm (0") sheaves for, mm (7/8") wire rope with swivel hook, hook latch, and swivel lock 6 mton (40 ton) hook block with two 50,8 cm (0") sheaves for, mm (7/8") wire rope with swivel hook, hook latch, and swivel lock 45 mton (50 ton) hook block with three 50,8 cm (0") sheaves for, mm (7/8") wire rope with swivel hook, hook latch, and swivel lock Optional ydraulic Test Kit: required to properly analyze the performance of the EPIC control system. Optional Service Interval Kits: for the regularly scheduled maintenance of general crane operations. Optional ighting Packages: consult Factory for available options. Optional Special Paint: in color(s) other than Manitowoc standard red and black. Optional Special Customer Decals: custom vinyl decal(s) of name and/or logo from artwork supplied by customer. Optional Export Packaging: basic crane, boom and jib sections. 5 54 mton (60 ton) hook block with three 50,8 cm (0") sheaves for, mm (7/8") wire rope with swivel hook, hook latch, and swivel lock 64 mton (70 ton) hook block with four 50,8 cm (0") sheaves for, mm (7/8") wire rope with swivel hook, hook latch, and swivel lock 8 mton (90 ton) hook block with four 50,8 cm (0") sheaves for, mm (7/8") wire rope with swivel hook, hook latch, and swivel lock 9 mton (00 ton) hook block with five 50,8 cm (0") sheaves for, mm (7/8") wire rope with swivel hook, hook latch, and swivel lock Optional D Blocks and hooks 7 mton (9 ton) Swivel hook with 40 kg (749 lb) weight ball mton (5 ton) hook block with two 76, cm (0") sheaves for,75 mm (-/4") wire rope with swivel hook, hook latch, and swivel lock 6 mton (40 ton) hook block with two 76, cm (0") sheaves for,75 mm (-/4") wire rope with swivel hook, hook latch, and swivel lock 8 mton (90 ton) hook block with two 76, cm (0") sheaves for,75 mm (-/4") wire rope with swivel hook, hook latch, and swivel lock 9 mton (00 ton) hook block with two 76, cm (0") sheaves for,75 mm (-/4") wire rope with swivel hook, hook latch, and swivel lock Optional US Standard Tool Kit: includes all US tools required for routine maintenance (with the exception of a torque wrench). Optional Applications Optional & EX Clamshell: includes 5,9 cm (0-7/6") diameter laggings with helical grooves for, mm (7/8") rope for front and rear drums. Tagline, Rud-O-Matic No. 48 two barrel with 50,8 cm (0") wheel for maximum 4,4 m (80') boom. point roller guide. Pressure rollers on both drums. Clamshell control system - upgrade to basic machine. Optional D Clamshell: includes laggings with helical grooves for,75 mm (-/4") rope for front and rear drums. Tagline, Rud-O-Matic No. 848 three barrel with 76, mm (0") wheel for maximum m (00') boom. point roller guide. Pressure rollers on both drums. Clamshell control system - upgrade to basic machine. NOTE: D clamshell package requires the purchase of D high pull rear hoist drum. Optional & EX Dragline: includes 5,9 cm (0-7/6") diameter laggings with helical grooves for, mm (7/8") rope for both front and rear drums. Fairlead, hinged type with roller bearing steel sheaves. point roller guide. Pressure rollers on both drums. Optional D Dragline: includes 5,9 cm (0-7/6") diameter laggings with helical grooves for,75 mm (-/4") rope for both front and rear drums. Fairlead, hinged type with roller bearing steel sheaves. point roller guide. Pressure rollers on both drums. Optional Pile Driving: includes extended lower boom point shaft for attachment of fixed pile leads.
outline dimensions 6
outline dimensions Basic Crane x ength,86 m 8' " Width (retracted),66 m ' 0" eight,56 m ' 8" Weight () 4 0 kg 9,88 lb Weight (EX) 44 4 kg 97,77 lb Weight (D) 45 49 kg 99,756 lb Note: Weight includes crawlers, carbody, and upperworks with hydraulic fluid, half tank of fuel, standard wire rope, gantry, and boom butt. 7 B Basic Crane with crawlers removed x ength,86 m 8' " Width,66 m ' 0" eight,5 m 0' 8" Base, m 0' 7" Weight () 4 657 kg 54,60 lb Weight (EX) 6 680 kg 58,89 lb Weight (D) 7 804 kg 6,98 lb Note: Weight includes carbody, and upperworks with hydraulic fluid, half tank of fuel, standard wire rope, gantry, and boom butt. W W Crawlers x ength 6,8 m ' 5" Width,07 m ' 6" eight,09 m ' 7" Weight 8 654 kg 79 lb W W Inner Counterweight x ength,66 m ' 0" Width 0,84 m ' 9" eight,85 m 6' " Weight 97 kg 8,500 lb Outer Counterweight x ength,66 m ' 0" Width 0,69 m ' " eight,85 m 6' " Weight 49 kg 4,800 lb
outline dimensions 8 W Middle Counterweight - Series B x ength,66 m ' 0" Width 0,4 m ' 4" eight,85 m 6' " Weight 4 56 kg 0,000 lb W Crawler Frame Counterweights - Series B x 4 ength 0,89 m ' " Width 0,66 m ' " eight 0,6 m ' " Weight each 588 kg,500 lb & EX top & Pendants x ength 6,76 m ' " Width,0 m 4' " eight,7 m 4' 6" Weight 077 kg,75 lb No. Main, m (0') Insert & Pendants x, ength,5 m 0' 4" Width,0 m 4' " eight,5 m 5' 0" Weight 75 kg 86 lb No. Main 6, m (0') Insert & Pendants x, ength 6,0 m 0' 4" Width,0 m 4' " eight,5 m 5' 0" Weight 60 kg,45 lb No. Main, m (40') Insert & Pendants x,, ength,9 m 40' 4" Width,0 m 4' " eight,5 m 5' 0" Weight 089 kg,400 lb D top & Pendants x ength 6,40 m ' 0" Width,0 m 4' " eight,6 m 5' 4" Weight 654 kg 5,850 lb Optional
outline dimensions No. D Main, m (0') Insert & Pendants x, ength,5 m 0' 4" Width,0 m 4' " eight,5 m 5' 0" Weight 480 kg,059 lb 9 No. D Main 6, m (0') Insert & Pendants x, ength 6,0 m 0' 4" Width,0 m 4' " eight,5 m 5' 0" Weight 86 kg,8 lb No. D Main, m (0') Insert & Pendants x, ength,9 m 0' 4" Width,0 m 4' " eight,5 m 5' 0" Weight 089 kg,400 lb Note: same insert as No. Main No. 0 Fixed Jib, m (0') Strut & Pendants x, ength 9,5 m ' 4" Width 0,7 m ' 4" eight,4 m 4' " Weight 78 kg,604 lb No. 0 Jib Inserts, m (0') Strut & Pendants x,, ength, m 0' " Width 0,6 m ' 0" eight 0,6 m ' 0" Weight 05 kg lb Upper Point x ength,7 m 4' " Width 0,66 m ' " eight 0,5 m ' 9" Weight 5 kg 8 lb Optional
outline dimensions 0 No. 60 Main 8,8 m (9') Transition Insert & Pendants x ength 8,99 m 9' 4" Width,9 m 6' 4" eight,59 m 8' 6" Weight 9 kg,687 lb No. 60 Main, m (0') Insert & Pendants x ength,5 m 0' 4" Width,6 m 5' 4" eight,5 m 5' 0" Weight 4 kg 905 lb No. 60 Main 6, m (0') Insert & Pendants x, ength 6,0 m 0' 4" Width,6 m 5' 4" eight,5 m 5' 0" Weight 674 kg,485 lb No. 60 Main, m (40') Insert & Pendants x ength,9 m 40' 4" Width,6 m 5' 4" eight,5 m 5' 0" Weight kg,670 lb No. 60 Cap, m (7') & No. uffing Jib Butt 5,8 m (9') & Strut Assembly x ength 8,05 m 6' 5" Width,6 m 5' 4" eight,54 m 8' 4" Weight 744 kg 6,050 lb Optional
outline dimensions W, EX ook block for, mm (7/8") wire rope Capacity 9 mt 00 t ength,7 m 5' 7" Weight kg,47 lb Width 0,6 m ' " Capacity 8 mt 90 t ength,5 m 5' " Weight 974 kg,48 lb Width 0,6 m ' " Capacity 54,4 mt 60 t ength, m 4' 4" Weight 66 kg,400 lb Width 0,6 m ' " Capacity 45,4 mt 50 t ength, m 4' 4" Weight 595 kg,0 lb Width 0,6 m ' " Capacity 6, mt 40 t ength, m 4' " Weight 590 kg,00 lb Width 0,6 m ' " Capacity 7, mt 0 t ength, m ' 9" Weight 55 kg,78 lb Width 0,6 m ' " W D ook block for,75 mm (-/4") wire rope Capacity mt 00 t ength,8 m 5' " Weight 978 kg 4,6 lb Width 0,9 m ' 0" Capacity 8,0 mt 90 t ength,8 m 5' " Weight 978 kg 4,6 lb Width 0,9 m ' 0" Capacity 6, mt 40 t ength,7 m 5' 6" Weight 495 kg,95 lb Width 0,9 m ' " Capacity,0 mt 5 t ength,7 m 5' 6" Weight 495 kg,95 lb Width 0,9 m ' " & EX Weight Ball Capacity/Swivel,6 mt t Diameter 0,5 m ' 6" Weight 6 kg 740 lb ength, m 4' 0" Capacity/Non-Swivel,6 mt t Diameter 0,5 m ' 6" Weight 6 kg 740 lb ength, m 4' 0" D D Weight Ball Capacity/Swivel 7 mt 9 t Diameter 0,5 m ' 6" Weight 40 kg 749 lb ength, m 4' 0" Optional
transport data Trailer oad Out Summary Model Series B No. 0 Fixed Jib 8, m (60') on No. Main m (90') Item Weight Quantity on each Item Trailer oad # kg (lb) Trailer oad Out Summary Model Series B No. 0 Fixed Jib 8, m (60') on No. uffing Jib 9,6 m (0') on No. 60 8, m (5') Item Weight Quantity on each Item Trailer oad # Trailer oad # kg (lb) 4 5 No. Basic Crane with Crawlers 4 0 (9,88) No. Basic Crane with Crawlers 4 0 (9,88) Standard Outer Counterweight 49 (4,800) Standard Outer Counterweight 49 (4,800) Standard Inner Counterweight 97 (8,500) Standard Inner Counterweight 97 (8,500) Series B Middle Counterweight 4 56 (0,000) Series B Middle Counterweight 4 56 (0,000) SeriesB Crawler Frame Counterweight 588 (,500) SeriesB Crawler Frame Counterweight 588 (,500), m (40') No. Insert, Pendants 089 (,400), m (40') No. Insert, Pendants 089 (,400) 6, m (0') No. Insert, Pendants 60 (,45),0 m (0') No. Insert, Pendants 75 (86),0 m (0') No. Insert, Pendants 75 (86) Standard Top 5,9 m (9') 077 (,75) Standard Top 5,9 m (9') 077 (,75) Upper Point 5 (8) Upper Point 5 (8) 9, m (0 ) No. 0 Fixed Jib Basic 78 (,604) 9, m (0 ) No. 0 Fixed Jib Basic 78 (,604),0 m (0 ) No. 0 Jib Insert, Pendants 05 (),0 m (0 ) No. 0 Jib Insert, Pendants 05 () ook Block mton (00 ton) (,47) ook Block mton (00 ton) (,47) Weight Ball 6 (740) Weight Ball 6 (740), m (40') No. 60 Insert, Pendants (,670) Approximate Total Shipping Weight kg (lb) 4 7 (96,68) 0 594 (45,400) 0 84 (45,946) 6, m (0') No. 60 Insert, Pendants,0 m (0') No. 60 Insert, Pendants 674 (,485) 4 (905) 8,8 m (9') No. 60 Transition, Pendants,0 m (0') No. 60 Cap with attached 4,5 m (5') No. uffing Jib Butt, Pendants,Strut Assembly, Rope Guide 9 (,687) 744 (6,050) Approximate Total Shipping Weight kg (lb) 4 7 (96,68) 0 594 (45,400) 9 4 (4,0) 96 (5,060) 96 (8,77)
crane assembly Fast Self Assembly Three Trucks, Three People, Three ours Extremely well designed and utilizing efficient use of space allows the Manitowoc Model to be mobilized with only three people using three trucks in three hours - or less - with maximum boom, fixed jib and counterweight.
performance data 4 Wire Rope engths - No. Main or No. 0 Fixed Jib on No. Main or and Fixed Jib ength, 5, 8,, 4,4 7,4 (00),5 (0) 6,6 (0) 9,6 (0) 4,7 45,7 5,8 54,9 6,0 (00) 64,0 (0) 67, (0) 70, (0) 7, 76, Whip ine Rear Drum ( part of line) 8 44 50 56 6 69 75 8 87 9 99 05 7 0 6 4 48 54 60 (05) (5) (45) (65) (85) (05) (5) (45) (65) (85) (05) (5) (45) (65) (85) (405) (45) (445) (465) (485) (505) (55) m 5 8 98 06 06 06 Front Drum oist line (ft) (500) (600) (650) (675) (675) (675) (75) (75) (75) (75) (75 ) (75) (75) (75) (75) (75) (75) Maximum Required parts of line* Note: oist line and whip line lengths given in table will allow hook to touch ground. When block travel below ground in required, add additional rope equal to parts of line times added travel distance. oisting distance or line pull may be limited when block travel below ground is required. * Based on 89 kn (0 kips) maximum single line pull. 0 0 9 8 7 6 6 5 4 4 4 Wire Rope engths - No. D Main or No. 0 Fixed Jib on No. D Main or and Fixed Jib ength, 5, 8,, 4,4 7,4 (00),5 (0) 6,6 (0) 9,6 (0) 4,7 45,7 5,8 54,9 Whip ine Rear Drum ( part of line) 8 44 50 56 6 69 75 8 87 9 99 05 7 (05) (5) (45) (65) (85) (05) (5) (45) (65) (85) (05) (5) (45) (65) (85) Drum Capacities - Wire Rope Front or Rear Drum, mm (7/8") Wire Rope* Auxiliary Drum 5,88 mm (5/8") Wire Rope** oist line Front Drum m 85 04 49 49 49 49 49 (ft) (40) (400) (400) (45) (45) (45) (490) (490) (490) (490) (490) Note: oist line and whip line lengths given in table will allow hook to touch ground. When block travel below ground in required, add additional rope equal to parts of line times added travel distance. oisting distance or line pull may be limited when block travel below ground is required. * Based on 78 kn (40 kips) maximum single line pull. Maximum ength No agging 50 m (89 ft) 6 ayers 80 m (64 ft) 4 ayers Maximum Required parts of line* 5 5 5 4 4 With agging 65 m (870 ft) 6 ayers Front or Rear Drum,75 mm (-/4") Wire Rope*** oist Drum 5,88 mm (5/8") Wire Rope 4 m (470 ft) 4 ayers m (40 ft) 5 ayers * 5 m (6') is deducted from maximum spooling capacities for dead wraps per drum or lagging for, mm (7/8") wire rope. ** m (9') is deducted from maximum spooling capacities for dead wraps on Auxiliary Drum for, mm (7/8") wire rope. *** 6 m (') is deducted from maximum spooling capacities for dead wraps per drum or lagging for,75 mm (-/4") wire rope.
performance data Wire Rope engths - No. uffing Jib on No. 60 Main Only (Includes All uffing Jib engths) 6,8 (55) 9,8 (65),9 (75) 5,9 (85) (95),0 (05) 5, (5) 8, (5) 4, (5) 44, (45) Front Drum m 98 9 9 6 5 5 5 5 5 oist ine (ft) (650) (700) (750) (750) (775) (85) (85) (85) (85) (85) Maximum Required Parts of ine* 4 4 4 4 Intermediate Fall ine Auxiliary Auxiliary Drum Drum ( Part of ( Parts of line**) line**) 46 5 58 64 70 76 8 88 94 0 (0) (0) (70) (0) (0) 64 7 8 9 0 07 (0) (70) (00) (0) Note: oist line lengths given in table include all luffing jib lengths. oist and intermediate fall line lengths given in table will allow hook to touch ground. When block travel below ground in required, add additional rope equal to parts of line times added travel distance. oisting distance or line pull may be limited when block travel below ground is required. * Based on 89 kn (0 kips) line pull. ** Based on 50 kn (.5 kips) line pull. Wire Rope engths - No. 0 Fixed Jib on No. uffing Jib on No. 60 Main and uffing Jib and Fixed Jib ength 74,7 (45) 77,7 (55) 80,8 (65) 8,8 (75) 86,9 (85) 89,9 (95) 9,0 (05) 96,0 (5) oist ine Front Drum ( Part of line*) m 6 68 74 80 86 9 98 04 (ft) (550) (570) (590) (60) (650) (670) Note: oist line lengths given in table include all luffing jib lengths and fixed jib lengths. oist and intermediate fall line lengths given in table will allow hook to touch ground. When block travel below ground in required, add additional rope equal to parts of line times added travel distance. oisting distance or line pull may be limited when block travel below ground is required. * Based on 89 kn (0 kips) line pull. 5 Wire Rope Specifications Part Number Function No. 79 oist ine.5: Safety Factor Regular ay, 6x5 Filler Wire, Extra Improved Plow Steel, IWRC No. 79 Whip ine No. 797 uffing Jib Intermediate Fall ine No. 7944 oist ine 5: Safety Factor Rotation Resistant, 60 N/mm DYFORM 4R 60 No. 7944 Whip ine No. 7947 uffing Jib Intermediate Fall ine Size Wire Rope Minimum Breaking Strength Maximum oad Per ine Approximate Weight, mm (7/8") 6 0 kg (79,600 lb) 9 070 kg (0,000 lb), kg/m (.4 lb/ft), mm (7/8") 6 0 kg (79,600 lb) 9 070 kg (0,000 lb), kg/m (.4 lb/ft) 5,88 mm (5/8") 0 590 kg (45,400 lb) 5 00 kg (,50 lb),07 kg/m (0.7 lb/ft), mm (7/8") 48 40 kg (06,0 lb) 9 070 kg (0,000 lb),46 kg/m (.65 lb/ft), mm (7/8") 48 40 kg (06,0 lb) 9 070 kg (0,000 lb),46 kg/m (.65 lb/ft) 5,88 mm (5/8") 5 590 kg (56,40 lb) 5 00 kg (,50 lb),5 kg/m (0.84 lb/ft)
performance data 6 oist Drum - 89 kn (0 kips) Full Power Drum - Continuous Duty Single ine Pull/Single ine Speed oist Drum - 78 kn (40 kips) Full Power Drum - Continuous Duty Single ine Pull/Single ine Speed ayer m/min (ft/min) 4 5 6 ayer m/min (ft/min) 4 ine Pull kg (lb) 0) (0) (95) (40) 4 (465) 5 (500) 6 (55) 74 (570) ine Pull kg (lb) 0) (0) 6 (07) 69 (7) 75 (46) 8 (66) 68) (5,000) (69) (99) (49) 40 (458) 48 (487) 57 (55) 4 56) (0,000) 59 (95) 65 () 69 (8) 75 (45) 4 56) (0,000) 05 (4) (68) 9 (89) 0 (94) (99) (404) 9 07) (0,000) 55 (8) 60 (96) 64 (0) 68 () 6 80) (5,000) 8 (7) 84 (76) 86 (8) 87 (86) 89 (9) 90 (96) 608) (0,000) 47 (54) 48 (58) 49 (6) 5 (67) 9 07) (0,000) 66 (8) 68 () 69 (7) 7 () 7 (7) 74 (4) 8 44) (40,000) 9 (7) 40 () 4 (5) 4 (9) NOTE: ine pull is infinitely variable. NOTE: ine pull is infinitely variable. Auxiliary Drum - 66,7 kn (5 kips) ayer ine Pull kg (lb) 0) (0) Full Power Drum - Continuous Duty Single ine Pull/Single ine Speed m/min (ft/min) 60 (96) 66 (5) 7 (4) 4 77 (5) 68) (5,000) 59 (9) 64 (09) 70 (8) 75 (45) 4 56) (0,000) 57 (88) 6 (04) 66 (8) 7 () 6 80) (5,000) 54 (76) NOTE: ine pull is infinitely variable. Auxiliary Drum - kn (5 kips) Full Power Drum - Continuous Duty Single ine Pull/Single ine Speed ayer m/min (ft/min) 4 5 6 7 8 9 ine Pull kg (lb) 0) (0) 4 () 46 (5) 5 57 (88) 6 (06) 69 (5) 74 (4) 80 (6) 85 68) (5,000) 4 56) (0,000) 6 80) (5,000) 9 07) (0,000) 40) (5,000) 4 () 40 (0) 9 (7) 7 () 6 (7) 46 (50 45 (48) 44 (4) 4 (7) NOTE: ine pull is infinitely variable. 5 (68 50 (64) 48 (57) 46 57 (86) 55 5 (7) 6 (0) 60 (96) 56 (85) 67 () 65 () 60 (97) 7 (9) 69 (8) 78 (55) 74 (4) 8 (7) 79 (58)
performance data Maximum ength Unassisted Raising Method Over end of blocked crawlers m (ft) No. 0 Fixed Jib on No. Main, EX, EX Series B Main 6,0 (00) Fixed Jib 8, Main 6,0 (00) Fixed Jib 8, Maximum ength Unassisted Raising Method No. uffing Jib on No. 60 Main, EX Series B In-ine Procedure Jack-Knife Procedure Main uffing Jib Main uffing Jib 6,8 (55) 9,8 (65) 5, - 6,6 (50-0) 5, -,5 (50-0) 6,8 (55) 9,8 (65) 9,6-45,7 (0-50) 6,6-45,7 (0-50) 7 Over side of extended crawlers m (ft) 6,0 (00) 54,9 5,8 8, 6,0 (00) 54,9 5,8, 8, Over end of blocked crawlers m (ft),9 (75) 5,9 (85) (95),0 (05) 5, - (50-00) 5, - 4,4 (50-80) 5, -, (50-70) 5, - 8, (50-60),9 (75) 5,9 (85) (95),0 (05),5-45,7 (0-50) 7,4-45,7 (90-50) 4,4-45,7 (80-50), - 45,7 (70-50) Over side of retracted crawlers m (ft) 54,9 5,8 5, 8, 5,8 45,7 5, 5, (5) 8, (5) 4, (5) 44, (45) NOTE: oad block(s), hook(s) and weight ball(s) on ground at start. 5, - 45,7 (50-50) 5, - 4,7 (50-40) 5, - (50-00) 8, 4,7 8, NOTE: oad block(s), hook(s) and weight ball(s) on ground at start. Maximum ength Unassisted Raising Method Over end of blocked crawlers m (ft) No. 0 Fixed Jib on No. uffing Jib on No. 60 Main, EX Series B Jack-Knife Procedure Main 5, (5) 8, (5) 4, (5) uffing Jib - 9,6 (00-0) - 9,6 (00-0) (00) Fixed Jib 9, - 8, (0-60) 9, - 8, (0-60) 9, - 8, (0-60) NOTE: oad block(s), hook(s) and weight ball(s) on ground at start. Working Weight Configuration, m (40') No. Main m (90') No. Main combined with 8, m (60') No. 0 Fixed Jib kg (lb) Series B 79 85 (76,04) 85 48 (87,74) 68 965 (5,04) 74 60 (6,74) Typical working weight consists of: hydraulic reservoirs full, fuel half-full, drums loaded with standard lengths of wire rope, upper boom point, 9 mt (00 t) hook block, and standard weight ball. Note: Upper boom point not used with fixed jib.
boom combinations 8 No. eavy-ift Combinations ength, 5, 8,, 4,4 Inserts 6, m (0 ft), m (0 ft), m (40 ft) No. D eavy-duty Combinations ength, 5, 8,, 4,4 Inserts 6, m (0 ft), m (0 ft), m* (40 ft) No. 0 Fixed Jib Combinations Jib ength 9, (0), 5, 8, Fixed Jib Inserts,m (0 ft) 7,4 (00),5 (0) 7,4 (00),5 (0) 4,6 m (5 ft) No. 0 Jib Top 6,6 (0) 9,6 (0) 4,7 6,6 (0) 9,6 (0) 4,7 No. 0 Fixed Jib 8, m (60 ft),0 m (0 ft) No. 0 Jib Insert 45,7 45,7 5,8 54,9 6,0 (00) 6,4 m ( ft) No. Top *, m (40') insert same as No. Main. 4,6 m (5 ft) No. 0 Jib Butt 6,4 m ( ft) No. Top, m (40 ft) No. Insert, m (40 ft) No. Insert 6,4 m ( ft) No, D Top, m (40 ft) No. Insert, m (40 ft) No. Insert, m (40 ft) No. Insert No., EX Main 6,0 m (00 ft), m (40 ft) No. Insert No. D Main 45,7 m (50 ft), m (40 ft) No. Insert No., EX Main m (90 ft), m (40 ft) No. Insert 6, m (0 ft) No. Insert,0 m (0 ft) No. Insert 5,8 m (9 ft) No. Butt 6, m (0 ft) No. D Insert,0 m (0 ft) No. D Insert 5,8 m (9 ft) No. D Butt 6, m (0 ft) No. Insert,0 m (0 ft) No. Insert 5,8 m (9 ft) No. Butt Model Series B No. Main 6,0 m (00 ft) Model Series B No. D Main 45,7 m (50 ft) Model Series B No. 0 Fixed Jib on No. Main 76, m (50 ft)
boom combinations No. 60 Main Combinations ength 6,8 (55) Inserts 6, m (0 ft), m (0 ft), m (40 ft),0 m (0 ft) No. 0 Jib Insert 4,6 m (5 ft) No. 0 Jib Top 9 9,8 (65),9 (75) 5,9 (85) 6,4 m ( ft) No. Top 4,6 m (5 ft) No. 0 Jib Butt No. 0 Fixed Jib 8, m (60 ft) (95),0 (05) 5, (5) 8, (5) 4, (5) 44, (45) No. uffing Jib 45,7 m (50 ft), m (40 ft) No. Insert 6,4 m (5 ft) No. Top No. uffing Jib Combinations uffing Jib ength uffing Jib Inserts, m 6, m, m (0 ft) (0 ft) (40 ft), m (40 ft) No. Insert No. uffing Jib 9,6 m (0 ft), m (40 ft) No. Insert 5, 8,, 4,4 6, m (0 ft) No. Insert, m (40 ft) No. Insert 7,4 (00),5 (0) 6,6 (0) 9,6 (0) 4,7 45,7,0 m (0 ft) No. Insert 5,8 m (9 ft) No. 60 uffing Jib Butt, m (7 ft) No. 60 Cap,0 m (0 ft) No, Insert 5,8 m (9 ft) No. 60 uffing Jib Butt, m (7 ft) No. 60 Cap No. 60 Main 5, m (5 ft), m (40 ft) No. 60 Insert, m (40 ft) No. 60 Insert 6, m (0 ft) No. 60 Insert 6, m (0 ft) No. 60 Insert 8,8 m (9 ft) No. 60 Transition Insert 5,8 m (9 ft) No. Butt No. 60 Main 8, m (5 ft),0 m (0 ft) No. 60 Insert 8,8 m (9 ft) No. 60 Transition Insert 5,8 m (9 ft) No. Butt Model Series B No. uffing Jib on No. 60 Main 80,8 m (65 ft) Model Series B No. 0 Fixed Jib on No. uffing Jib on No. 60 Main 96,0 m (5 ft)
heavy-lift boom range diagram 0 No. Main (0) 64,0 8 80 (00) 6,0 70 54,9 6,0 (00) 60 5,8 54,9 45,7 45,7 5,8 50 4,7 4,7 40 (0) 9,6 9,6 (0) EIGT ABOVE GROUND (0) 6,6 (0),5 (00) 7,4 7,4 (00),5 (0) 6,6 (0) 0 4,4 4,4, 8, 8,, 0 5, 5,,, (0) 9, 4,4 m (4' 7") TAISWING SERIES B 0,97 m (' ") ROTATION,66 m 5' 6" 9, (0), 5, 8,, 4,4 7,4 (00),5 (0) DISTANCE FROM CENTERINE ROTATION 6,6 (0) 9,6 (0) 4,7 45,7
heavy-lift boom load charts iftcrane Capacities - Series B No. with Open Throat Top 8 70 kg (6,00 lb) Counterweight 6 50 kg (4,000 lb) Crawler Frame Counterweight 6,8 m (' 4") Crawlers extended 60 Rating kg (lb) x 000,0 (0), 90,7 (00.0) 8, 4,4 (00) 6,6 (0) 4,7 54,9 6,0 (00) 4,5 (5) 68, (48.) 66,0 (4.6) (.5) 6,0 (0) 49, (06.5) 47,0 (0.8) 44,0 (95.8) 4,7 (90.) (0) 8,4 (6.) 8, (6.) 7,9 (60.6) 6,6 (58.) 5, (54.7) 4,0 (5.0), (46.7) (4.5),0 6,6 (5.4) 9, (4.6) 9, (4.) 8,9 (4.0) 8, (9.) 7, (8.) 6,7 (6.0) 4,5 (.0) 0,7 (.) 8,0 0, (.4), (4.4), (4.0) 0,9 (.6) 0,7 (.) 0,0 (.6) 9, (0.) 8,9 (9.) 4,0 7,0 (4.5) 7,6 (6.5) 7,4 (6.) 7, (5.7) 7, (5.) 6,6 (4.) 6,0 (.9) 0,0 (00) 4,8 (0.0) 5,4 (.7) 5, (.) 5,0 (0.9) 4,6 (0.0) 4, (8.8) 6,0 (0), (6.7),8 (8.),6 (7.7), (7.0),8 (6.0) 4,0 46,0 (55), (4.),4 (5.),6 (.), (4.8),6 (.),8 (4.0) Fixed Jib No. 0 on No. iftcrane Capacities No. with Open Throat Top 4 80 kg (5 00 lb) Counterweight 6,8 m (' 4") Crawlers extended 60 Rating kg (lb) x 000, 8, 4,4 (00) 6,6 (0) 4,7 54,9 6,0 (00) Jib ength 9, (0), 5, 8, Deduct from Capacity with fixed jib attached kg (lb) 770 (,700) 950 (,00) 70 (,600) 400 (,00),0 (0) 90,7 (00.0) 4,5 (5) 68, (48.) 66,0 (4.6) (.5) 6,0 (0) 4,6 (9.8) 4,5 (9.7) 4,4 (9.5) 4,7 (90.) (0),9 (5.6),8 (5.4),7 (5.),5 (50.8),4 (50.5), (50.), (46.7) (4.5),0 6, (5.) 6, (4.8) 5,9 (4.5) 5,8 (4.) 5,6 (.9) 5,5 (.5) 5, (.) 4,5 (.0) 0,7 (.) 8,0 4,0 0,0 (00) 6,0 (0) 4,0 46,0 (55) 9,4 (0.5) 9, (0.) 6, (.7) 9, (9.8) 6, (.4) 4,5 (9.7) (9.5) 6,0 (.0) 4, (9.), (6.7) 8,8 (9.) 5,8 (.6) 4, (8.9),0 (6.5), (4.) 8,6 (8.8) 5,6 (.),9 (8.5),8 (6.),0 (4.4),6 (.) 8,5 (8.4) 5,4 (.8),7 (8.),6 (5.6),8 (4.0),4 (.0) 8, (8.0) 5, (.4),5 (7.6),4 (5.),6 (.5) Meets ANSI B0.5 Requirements - Capacities do not exceed 75% of static tipping load. NOTICE: This capacity chart is for reference only and must not be used for lifting purposes.
heavy-duty boom range diagram No. D Main (0) 64,0 (00) 6,0 54,9 5,8 8.9 80 45,7 4,7 4,7 45,7 70 60 EIGT ABOVE GROUND (0) 9,6 (0) 6,6 (0),5 (00) 7,4 7,4 (00),5 (0) 6,6 (0) 9,6 (0) 50 40 4,4 4,4 0,, 8, 5, 5, 8, 0,, (0) 9, 4,4 m (4' 7") TAISWING SERIES B 0,97 m (' ") ROTATION,66 m 5' 6" 9, (0), 5, 8,, 4,4 7,4 (00),5 (0) DISTANCE FROM CENTERINE ROTATION 6,6 (0) 9,6 (0) 4,7 45,7 45,7
heavy-duty boom load charts iftcrane Capacities - Series B No. D with Open Throat Top 8 70 kg (6,00 lb) Counterweight 6 50 kg (4,000 lb) Crawler Frame Counterweight 6,8 m (' 4") Crawlers extended 60 Rating kg (lb) x 000, 8, 4,4 (00) 6,6 (0) 4,7 45,7,0 (0) 90,7 (00.0) 4,0 () 76,8 (7.0) 77,4 (70.7) 4,5 (5) 68, (48.) 67,5 (45.8) 6,0 (0) 50,7 (09.) 47,5 (0.7) 4,8 (94.6) 4,0 (88.5) (0) 7,4 (59.) 7, (58.6) 7,0 (58.) 5, (54.6),9 (5.6),5 (48.6), (47.8),0 6,4 (4.) 8,0 (8.9) 7,8 (8.5) 7,5 (8.0) 7,4 (8.0) 6,9 (6.) 6,6 (5.5) 8,0 8,7 (8.) 9,8 (.) 9,6 (0.8) 9,6 (0.7) 9, (9.6) 8,9 (9.) 4,0 4,9 (0.) 6,0 (.0) 6,0 (.0) 5,5 (.8) 5,4 (.7) 0,0 (00),6 (5.),6 (7.6), (7.0), (7.) 6,0 (0) 8,0 (5) iftcrane Capacities No. D with Open Throat Top 4 80 kg (5,00 lb) Counterweight 6,8 m (' 4") Crawlers extended 60 Rating kg (lb) x 000,0 (0), 90,7 (00.0) 8, 4,4 (00) 6,6 (0),7 (.4) 4,7,8 (.7), (.0) 45,7 Fixed Jib No. 0 on No. D Jib ength 9, (0), 5, 8, Deduct from Capacity with fixed jib attached kg (lb) 770 (,700) 950 (,00) 70 (,600) 400 (,00) 4,0 () 4,5 (5) 75,9 (69.0) 67,9 (47.4) 75,8 (67.) 67, (45.8) 6,0 (0) 4,7 (9.8) 4,6 (9.5) 4,4 (9.) 4,0 (88.5) (0),0 8,0 4,0 0,0 (00) 6,0 (0),8 (49.) 5, (.6),6 (48.8) 4,9 (.) 8, (7.6),4 (48.) 4,7 (.7) 7,9 (7.) 4,7 (0.), (47.8) 4,4 (.) 7,7 (6.6) 4,6 (0.0),6 (5.), (47.7) 4,4 (.) 7,6 (6.5) 4,6 (9.9),8 (6.),9 (47.) 4, (0.6) 7,4 (5.9) 4, (9.),6 (5.6),5 (.),0 (47.) 4, (0.7) 7,4 (6.0) 4,4 (9.4),6 (5.7),5 (.) Meets ANSI B0.5 Requirements - Capacities do not exceed 75% of static tipping load. NOTICE: This capacity chart is for reference only and must not be used for lifting purposes.
fixed jib range diagram 4 (70) 8, No. 0 Fixed Jib on No. Main (60) 79, 8 0 80 76, 0 0 7, 0 70 8, (0) 70, 5, 7, 60 (0) 67,, 70, (0) (0) 64,0 9, (0) 67, (0) (00) 6,0 64,0 (0) 6,0 (00) 50 54,9 5,8 54,9 EIGT ABOVE GROUND 45,7 4,7 (0) 9,6 (0) 6,6 6,6 (0) 9,6 (0) 4,7 45,7 5,8 40 (0),5,5 (0) (00) 7,4 7,4 (00) 0 0 0 0 4,4 4,4,, 8, 5,, (0) 9, 4,4 m (4' 7") TAISWING SERIES B 0,97 m (' ") ROTATION,66 m 5' 6" 9, (0), 5, 8,, 4,4 7,4 (00),5 (0) DISTANCE FROM CENTERINE ROTATION 6,6 (0) 9,6 (0) 4,7 45,7 5,8 54,9
fixed jib load charts Jib ength 9, m (0 ft) iftcrane Jib Capacities - Series B Jib No. 0 with,8 m (' 6") Strut on No. with Open Throat Top 8 70 kg (6,00 lb) Counterweight 6 50 kg (4,000 lb) Crawler Frame Counterweight 6,8 m (' 4") Crawlers extended 60 Rating kg (lb) x 000 7,6 (5) 0,0 (0),0 6,0 8,0,0 6,0 4,0 (0) 4,0, 8,7 7, (4.6) 0 Offset 9,6 (00) (0) 8,6 (9.7) 6,8 (4.0) 4,6 (0.5) 8, (8.9) 6,4 (.) 4, (9.8),8 (6.0) 7, (7.0) 5,8 (.9),8 (8.6),4 (5.) (7.) 7,5 (6.6) 7,5 (6.6) 6,5 (5.) 5,0 (0.), (7.),8 (4.0), 8, (8.) 7,0 (5.9) 6,5 (4.) 0 Offset 9,6 (00) (0) (9.5) 7,7 (7.5) 7, (5.9) 6,5 (4.6) 8, (8.6) 7,8 (7.) 7,0 (5.8) 6,4 (.8) 8,6 (9.4) 8, (8.0) 7,5 (6.8) 6, (.7) (4.) 8,5 (8.7) 7,0 (6.) 5,4 (.),4 (7.8) 5 46,0,9 (4.) (.) 50,0, 0 Offset 0 Offset, (00) 9,6 (0), (00) 9,6 (0) 7,6 (5) 0,0 (0) Jib ength, m (40 ft),0 6,0 8,0,0 6,0 4,0 (0) 4,0 46,0 50,0 7,5 (7.4) 6, (.8) 8,6 (9.7) 6,8 (4.0) 4,7 (0.6) 8, (9.0) 6,4 (.) 4, (9.8),9 (6.) (5.) 7, (6.9) 5,8 (.9),8 (8.6),4 (5.),9 (4.4),4 7,7 (7.0) 7,7 (7.0) 6,4 (5.0) 5,0 (0.), (7.),8 (4.0) (.) (4.8) 5,7 (.0) 5, (.6) (0.6) 6, (4.0) 5,8 (.7) 5, (.6) 6,4 (4.6) 6, (.4) 5,5 (.4) 5,0 (0.9) 6,4 (4.0) 5,8 (.) 5, (.6) 4, (9.5) (4.5) 6,0 (.6) 5,6 (.4),5 (8.0) Meets ANSI B0.5 Requirements - Capacities do not exceed 75% of static tipping load. NOTICE: This capacity chart is for reference only and must not be used for lifting purposes.
fixed jib load charts 6 iftcrane Jib Capacities - Series B Jib No. 0 with,8 m (' 6") Strut on No. with Open Throat Top 8 70 kg (6,00 lb) Counterweight 6 50 kg (4,000 lb) Crawler Frame Counterweight 6,8 m (' 4") Crawlers extended 60 Rating kg (lb) x 000 0,0 (0), 0 Offset (00) 9,6 (0), (00) 0 Offset 9,6 (0),0 Jib ength 5, m (50 ft) 6,0 8,0,0 6,0 4,0 (0) 4,0 8,4 (8.) 6,5 (4.9) 5, (.0) 8,9 (9.8) 8, (8.8) 6,8 (4.) 4,7 (0.6) 8,8 (9.5) 8, (8.8) 6,5 (.) 4, (9.8),0 (6.4) 8,6 (9.) 8,4 (8.6) 7, (6.8) 5,7 (.8),7 (8.5),5 (5.) 7,6 (6.9) 7,5 (6.7) 6,4 (4.9) 5,0 (0.),0 (7.0),8 (4.0) 4,8 (.0) 4,4 (9.8),9 (8.9) 4,8 (0.5) 4, (9.6),8 (8.) (.0) 4,5 (0.) 4, (8.9) (7.9) 4,7 (0.6) 4, (9.),7 (8.4) 4,8 (0.9) 4,5 (9.7),6 (8.), (4.9) 46,0,4 (5.4),0 (4.5) (.) 50,0,5 (.0) 0,0 (0), 8, (8.) (00) 0 Offset 9,6 (0), (00) 0 Offset 9,6 (0),0 7,9 (7.5) 7,7 (7.0) (6.) Jib ength 8, m (60 ft) 6,0 8,0,0 6,0 4,0 (0) 4,0 46,0 50,0 7, (6.4) 6,9 (5.) 5,7 (.) 4,6 (9.7), (7.6) 7, (6.4) 7, (5.8) 6,6 (4.9) 5,9 (.) 4, (9.6), (7.) 7,0 (5.7) 6,9 (5.) 6,6 (4.8) 6, (.) 4, (9.8),0 (6.5),5 (5.6),9 6,5 (4.6) 6,5 (4.) 6, (4.0) 5,7 (.7),7 (8.5),4 (5.),0 (4.5),5 (.) 5,9 (.) 5,8 (.9) 5,7 (.7) 4,9 (0.0),0 (6.9),8 (.9) (.),8 (8.5), (7.6),0 (6.4) (9.0),6 (8.), (7.0),8 (8.6),4 (7.4),9 (6.6),9 (8.9),6 (7.8), (6.9),7 (8.0), (7.), (5.0) (4.) Meets ANSI B0.5 Requirements - Capacities do not exceed 75% of static tipping load. NOTICE: This capacity chart is for reference only and must not be used for lifting purposes.
fixed jib load charts iftcrane Jib Capacities Jib No. 0 with,8 m (' 6") Strut on No. with Open Throat Top 4 80 kg (5,00 lb) Counterweight 6,8 m (' 4") Crawlers extended 60 Rating kg (lb) x 000, 0 Offset (00) 9,6 (0), (00) 0 Offset 9,6 (0) 7 7,6 (5) 0,0 (0) Jib ength 9, m (0 ft),0 6,0 8,0,0 6,0 4,0 (0) 7, (6.8) 5,8 (.0) (9.9) 6,9 (6.) 5,5 (.),6 (8.) 8,7 (9.) 6,6 (5.) 5, (0.5), (7.6) 8,5 (8.5) 6, (4.6) 4,8 (9.8),0 (6.8) (7.) 7,5 (6.6) 7,5 (6.6) 6,0 (.9) 4,5 (9.),6 (6.) 8, (8.) 7,0 (5.9) 6,5 (4.) (9.5) 7,7 (7.5) 7, (5.9) 6,5 (4.6) 8, (8.6) 7,8 (7.) 6,9 (5.8) 5,4 (.0) 8,6 (9.4) 8, (8.0) 6,7 (5.6) 5, (0.5) (7.) 8,5 (8.7) 6,5 (5.) 4,9 (9.9),9 (6.7) 4,0, (4.9),9 (4.),5 (.4) 46,0,5 (.4), (00) 0 Offset 9,6 (0), (00) 0 Offset 9,6 (0) 7,6 (5) 0,0 (0) Jib ength, m (40 ft),0 6,0 8,0,0 6,0 4,0 (0) 4,0 46,0 7, (6.9) 5,8 (.) (9.9) 7,0 (6.) 5,5 (.),7 (8.4) 8,7 (9.) 6,6 (5.4) 5, (0.6), (7.6), (4.9) (4.) 8,5 (8.5) 6, (4.7) 4,8 (9.8),0 (6.9),9 (4.),5 (.5) 7,7 (7.0) 7,7 (7.0) 6,0 (4.0) 4,5 (9.),6 (6.),6 (.4) (4.8) 5,7 (.0) 5, (.6) (0.6) 6, (4.0) 5,8 (.7) 5, (.6) 6,4 (4.6) 6, (.4) 5,5 (.4) 5,0 (0.9) 6,4 (4.0) 5,8 (.) 5, (0.7), (7.5) (4.5) 6,0 (.6) 5,0 (0.),0 (7.0) Meets ANSI B0.5 Requirements - Capacities do not exceed 75% of static tipping load. NOTICE: This capacity chart is for reference only and must not be used for lifting purposes.
fixed jib load charts 8 iftcrane Jib Capacities Jib No. 0 with,8 m (' 6") Strut on No. with Open Throat Top 4 80 kg (5,00 lb) Counterweight 6,8 m (' 4") Crawlers extended 60 Rating kg (lb) x 000 0,0 (0), 0 Offset (00) 9,6 (0), (00) 0 Offset 9,6 (0) Jib ength 5, m (50 ft),0 6,0 8,0,0 6,0 4,0 (0) 4,0 8,4 (8.) 6,5 (4.9) 5, (.0) 8,9 (9.8) 7,0 (6.) 5,5 (.),7 (8.4) 8,8 (9.) 6,6 (5.4) 5, (0.6), (7.6), (4.9) 8,6 (9.) 8,4 (8.6) 6, (4.7) 4,8 (9.9),0 (6.9),9 (4.) 7,6 (6.9) 7,5 (6.7) 6,0 (4.0) 4,5 (9.),7 (6.),6 (.4) 4,8 (.0) 4,4 (9.8),9 (8.9) 4,8 (0.5) 4, (9.6),8 (8.) (.0) 4,5 (0.) 4, (8.9) (7.9) 4,7 (0.6) 4, (9.),4 (7.7) 4,8 (0.9) 4,5 (9.7), (7.),9 (4.) 46,0,9 (4.),5 (.5) 0 Offset 0 Offset, (00) 9,6 (0), (00) 9,6 (0) 0,0 (0) 8, (8.) Jib ength 8, m (60 ft),0 6,0 8,0,0 6,0 4,0 (0) 4,0 46,0 7,9 (7.5) 7, (6.4) 6,9 (5.) 5,7 (.) 4,6 (9.7), (7.6) 7,7 (7.0) 7, (6.4) 7, (5.8) 6,6 (4.9) 5,5 (.4),7 (8.4),6 (5.7) (6.) 7,0 (5.7) 6,9 (5.) 6,6 (4.9) 5, (0.6),4 (7.7), (4.9),9 (4.) 6,5 (4.6) 6,5 (4.) 6, (4.0) 4,9 (9.9),0 (6.9),9 (4.),5 (.5) 5,9 (.) 5,8 (.9) 5,7 (.7) 4,5 (9.),7 (6.),6 (.4),8 (8.5), (7.6),0 (6.4) (9.0),6 (8.), (7.0),8 (8.6),4 (7.4),9 (6.6),9 (8.9),6 (7.8), (6.9),7 (8.0), (7.),0 (4.) (.5) Meets ANSI B0.5 Requirements - Capacities do not exceed 75% of static tipping load. NOTICE: This capacity chart is for reference only and must not be used for lifting purposes.
luffing jib range diagram 85, No. uffing Jib on No. 60 Main 9 (70) 8, 75.9 70 (60) 79, 45,7 60 76, 7, 9,6 (0) 4,7 50 (0) 70, 6,6 (0) 40 (0) 67,,5 (0) (0) 64,0 (00) EIGT ABOVE GROUND (00) 6,0 54,9 5,8 5, 8,, 4,4 7,4 0 0 45,7 88 8 80 75 70 4,7 44, (45) (0) 9,6 4, (5) (0) 6,6 8, (5) (0),5 5, (5) (00),0 (05) 7,4 (95) 4,4 6,0 (85), 8, 9,8 (65),9 (75) 5,, (0) 9, 6,8 (55) 4,4 m (4' 7") TAISWING SERIES B 0,97 m (' ") ROTATION,66 m 5' 6" 9, (0), 5, 8,, 4,4 7,4 (00),5 (0) 6,6 (0) 9,6 (0) DISTANCE FROM CENTERINE ROTATION 4,7 45,7 5,8 54,9
luffing jib load charts 0 iftcrane uffing Jib Capacities - Series B uffing Jib No. on No. 60 8 70 kg (6,00 lb) Counterweight 6 50 kg (4,000 lb) Crawler Frame Counterweight 6,8 m (' 4") Crawlers extended 60 Rating kg (lb) x 000 88 Angle 6, (0) 6,8 (55),7 (70.0),9 (75) (95) 5, (5) 4, (5) 6, (0) 6,8 (55),9 (75) (95) 5, (5) 4, (5) uffing Jib ength 5, m (50 ft) 8,0 (6) (0),0 (6),0 4,0 (45) 8,0 0,0 (65) 4,0 5,6 (56.9), (50.7) 9,7 (4.6) 8, (9.8) 5,9 (5.9) 6,7 (59.) 4,7 (5.9),4 (47.) 9,5 (4.4) 6,7 (7.7) 5, (56.),7 (5.9) 0,9 (46.) 9,7 (4.) 6,9 (8.), (5.5),9 (48.0) 9,7 (4.5) 8,6 (40.7) 6,8 (7.8) 9,9 (4.6) 8,0 (9.9) 7, (7.4) 5,5 (4.7) uffing Jib ength 4,4 m (80 ft) 8,0 (6) (0),0 (6),0 4,0 (45) 8,0 0,0 (65) 4,0,9 (50.8),0 (45.9) 8,0 (9.9) 6,7 (6.5) 4,6 (.0),6 (5.) 0,4 (.4) 8, (7.4),8 (47.7) 9, (4.5) 8,0 (9.4) 6, (6.),0 (6.0) 0,4 (.4) 8, (7.8) 0,6 (45.) 8,5 (4.0) 7,6 (8.5) 5,9 (5.7),0 (6.0) 0,4 (.4) 8, (7.8) 8,8 (4.) 7, (8.0) 6,4 (6.0) 5,0 (.6),0 (5.9) 0,4 (.) 8, (7.7) (5.4) 5, (.5) 4,5 (.9),5 (0.),4 (5.0) 0,4 (.) 8, (7.7) 6,0 (85) 6,0 (85) (6.4) (6.4) (6.) (6.),0 (6) 6,8 (55) 5,4 (4.0),9 (75) (95) 5, (5) 8, (5),0 (6) 6,8 (55),9 (75) (95) 5, (5) uffing Jib ength 6,6 m (0 ft),0 4,0 (45) 8,0 4,0 8,0 0,0 (00) 4,0 (0) 40,0 (0) 44,0 (45) 46,0 4,5 (.6),8 (8.8) 0, (.4) 7,7 (6.8) 6, (4.) 5,7 (.) 4,6 (0.6) 5, (.),7 (0.8),4 (5.0) 7,8 (7.0) 6, (4.) 5,7 (.) 4,7 (0.6) 4, (.4), (9.5), (4.7) 7,8 (6.9) 6, (4.) 5,7 (.) 4,7 (0.6), (8.8), (7.) 0,6 (.) 7,8 (6.9) 6, (4.) 5,6 (.) 4,7 (0.6), (6.8),6 (5.9) 0, (.5) 7,8 (6.9) 6, (4.) 5,6 (.) 4,6 (0.6) uffing Jib ength 45,7 m (50 ft),0 4,0 (45) 8,0 4,0 8,0 0,0 (00) 4,0 (0) 40,0 (0) 44,0 (45) 46,0,5 (5.8) 9, (0.4) 7,0 (5.) 5,9 (.4) 5, (.6) 4,4 (0.0), (7.5), (5.) (.8),0 (6.9) 0, (.4) 7,5 (6.) 6,0 (.7) 5, (.6) 4,4 (0.0), (7.5),7 (6.) (5.5), (5.) 9,9 (.8) 7,5 (6.) 6,0 (.7) 5, (.6) 4,4 (0.0), (7.5),7 (6.0) (5.5) 9,8 (.9) 9, (0.) 7,5 (6.) 5,9 (.6) 5, (.4) 4, (9.7), (7.0),5 (5.6), (5.) Meets ANSI B0.5 Requirements - Capacities do not exceed 75% of static tipping load. NOTICE: This capacity chart is for reference only and must not be used for lifting purposes.
luffing jib load charts iftcrane uffing Jib Capacities - Series B uffing Jib No. on No. 60 8 70 kg (6,00 lb) Counterweight 6 50 kg (4,000 lb) Crawler Frame Counterweight 6,8 m (' 4") Crawlers extended 60 Rating kg (lb) x 000 70 Angle 8,0 6,8 (55), (4.),9 (75) (.) (95) 5, (5) 4, (5) 8,0 6,8 (55),9 (75) (95) 5, (5) 4, (5) uffing Jib ength 5, m (50 ft) 0,0 (65) 4,0 6,0 (85) 8,0 0,0 (00),0 (05) 4,0 (0) 6,0 (0) 9,7 (.8) 9, (0.9) 8,9 (9.9) 7,0 (5.) (.9) 6,5 (4.) 5,9 (.) (.) (.) 5,4 (.) 4,8 (.) uffing Jib ength 4,4 m (80 ft) 0,0 (65) 4,0 6,0 (85) 8,0 0,0 (00),0 (05) 4,0 (0) 6,0 (0) 7, (5.9) 6,6 (4.7) 5,9 (.5) 5, (.6) 7,0 (5.) 6, (.9) 5,6 (.8) 5, (.0) 4,6 (0.) (4.) 5,8 (.0) 5, (.0) 4,7 (0.) 4, (9.6) (8.9) 4,8 (.) 4,4 (9.5) 4,0 (8.9),6 (8.), (7.) 4,0 (8.6),6 (8.0), (7.4),9 (6.4) 8,0 (5) 8,0 (5),7 (6.0) 8,0 6,8 (55) 5,5 (.5),9 (75) (95) 5, (5) 8, (5) 8,0 6,8 (55),9 (75) (95) uffing Jib ength 6,6 m (0 ft),0 (05) 6,0 (0) 8,0 (5) 40,0 (0) 4,0 44,0 (45) 46,0 48,0 (55) 50,0 (65) 4,4 (9.9),6 (7.9), (7.4),0 (6.9),7 (6.0) 4, (9.),4 (7.),0 (6.8),8 (6.4),5 (5.5), (5.),8 (8.4), (6.7),8 (6.),5 (5.7), (5.0), (4.6) (4.),8 (6.0),5 (5.5), (5.),0 (4.4),8 (4.0),6 (.7),4 (.4),6 (5.6), (5.),0 (4.7),8 (4.0),6 (.7),5 (.4) (.) uffing Jib ength 45,7 m (50 ft),0 (05) 6,0 (0) 8,0 (5) 40,0 (0) 4,0 44,0 (45) 46,0 48,0 (55) 50,0 (65) 4,0 (9.0), (7.),0 (6.6),7 (6.),4 (5.), (4.8),0 (4.5),7 (4.),6 (.5),0 (6.5),7 (6.0),4 (5.5), (4.7),9 (4.),7 (4.0),6 (.7),4 (.),8 (8.4),0 (6.5),7 (6.0),4 (5.6), (4.7),0 (4.4),7 (4.0),6 (.7),4 (.) Meets ANSI B0.5 Requirements - Capacities do not exceed 75% of static tipping load. NOTICE: This capacity chart is for reference only and must not be used for lifting purposes.
fixed jib on luffing jib range diagram No. 0 Fixed Jib on No. uffing Jib on No. 60 Main (0) 97,6 66.6 75.8 (0) 94,5 8, (00) 9,5 5, 88,4, 85,4 9, (0) (70) 8, (60) 79, 70 76, 60 9,6 (0) 7, 6,6 (0) 50 (0) 70,,5 (0) (0) 67, (0) 64,0 (00) 40 EIGT ABOVE GROUND (00) 6,0 54,9 5,8 0 0 88 45,7 4,7 (0) 9,6 (0) 6,6 (0),5 8 80 5, (5) 4, (5) 8, (5) (00) 7,4 4,4, 8, 5,, (0) 9, 4,4 m (4' 7") TAISWING SERIES B 0,97 m (' ") ROTATION,66 m 5' 6" 9, (0), 5, 8,, 4,4 7,4 (00),5 (0) 6,6 (0) 9,6 (0) DISTANCE FROM CENTERINE ROTATION 4,7 45,7 5,8 54,9
fixed jib on luffing jib load charts iftcrane Fixed Jib on uffing Capacities - Series B Fixed Jib No. 0 on uffing Jib No. on No. 60 8 70 kg (6,00 lb) Counterweight 6 50 kg (4,000 lb) Crawler Frame Counterweight 6,8 m (' 4") Crawlers extended 60 Rating kg (lb) x 000 88 Angle uffing Jib,5 6,6 9,6 (00) (0) (0) (0) 5, (5) 8, (5) 4, (5) 5, (5) 8, (5) 5, (5) 8, (5) 5, (5) 8, (5) Fixed Jib ength 9, m (0 ft) 7 offset 4,0 (45) 8,0 8,0 6,0 (0) 46,0 50,0 (65) 8,7 (9.) 4,8 (.0),5 (7.6) 8, (7.9) 4,8 (.0),5 (7.6) 8,5 (8.9) 7,5 (6.5) 4,8 (0.9),4 (7.5) 8, (8.) 4,9 (.),5 (7.7) 7,6 (6.8) 4,9 (.),5 (7.7) 7,8 (7.) 5,0 (.4),5 (7.7),6 (5.8) 7, (5.8) 4,9 (.),6 (7.8),4 (5.5) 7, (6.0) 5, (.6),6 (7.8),4 (5.4),9 (4.) 6,7 (4.8) 4,9 (.),5 (7.7), (5.) 5, (5) 8, (5) 4, (5) 5, (5) 8, (5) 5, (5) 8, (5) 5, (5) 8, (5) 8,0 (8.0) (8.0) (8.0) (8.0) ( 8.0) 8,0 6,0 (0) 46,0 50,0 (65) 56,0 (85) 58,0,6 (8.0), (7.), (4.9),8 (4.),6 (8.0), (7.0), (4.7),8 (4.0),6 (8.0), (6.7),0 (4.5),7 (.8),6 (8.0),4 (7.4), (5.0),9 (4.),6 ( 8.0), (7.0), (4.8),8 (4.0),6 (8.0), (7.), (5.),9 (4.),5 (.5),6 (8.0), (6.9), (4.8),8 (4.0),5 (.),6 (8.0), (7.), (5.),9 (4.),5 (.).,6 (8.0), (6.8), (4.8),8 (4.0),4 (.),8 (4.) uffing Jib,5 6,6 9,6 (00) (0) (0) (0) Fixed Jib ength 8, m (60 ft) 7 offset Meets ANSI B0.5 Requirements - Capacities do not exceed 75% of static tipping load. NOTICE: This capacity chart is for reference only and must not be used for lifting purposes.
SM CraneCARE 4 CraneCARE is Manitowoc s comprehensive service and support program. It includes classroom and on-site training, prompt parts availability, expert field service, technical support and documentation for every one of the more than 7,000 Manitowoc cranes currently in use throughout the world. That s commitment you won t find anywhere else. That s CraneCARE. Primary Air Filter (Part No. 467-0) Secondary Air Filter (Part No. 4676-0),000 our Part No. 499974-0 Consists of the entire 00 our Service Kit (Part No. 49997-0), plus the following: ydraulic Filter in Tank (Part No. 4677-0) Filter, Breather (Part No. 9066-) ydraulic Filter - Spin on (Part No. 97050-) Service Training Manitowoc specialists work with you in our training center and in the field to make sure you know how to get maximum performance, reliability, and life from your cranes. Manitowoc Cranes Technical Training Center provides valuable multi-level training, which is available for all models and attachments, in the following format: Basic Provides technicians with the basic skills required in our evel I and II classes covering hydraulic and electrical theory and schematics, pump, motor, control, and MI operation, and the use of meters and gauges. evel one This model-specific class covers theory and offers hands-on training and trouble shooting for all crane systems. evel two This model-specific class provides in-depth coverage of all crane systems and components, and advanced troubleshooting of simulated faults. (Requires evel I.) Masters Covering all EPIC models and the 400W, this class stresses high level system knowledge and trouble shooting of simulated faults. (Requires evel II.) Parts Availability Genuine Manitowoc replacement parts are accessible through your distributor 4 hours a day, 7 days a week, 65 days a year. Service Interval Kits Provides all the parts required by Manitowoc s Preventative Maintenance Checklist. Cummins 6 CTA 8.C 7 kw (0 BP) Diesel 00 our Part No. 49997-0 Consists of the following: Engine Water Filter (Part No. 460-0) Primary Fuel Filter (Part No. 49-0) Secondary Fuel Filter (Part No. 49-0) Engine Oil Filter (Part No. 494-0),000 our Part No. 499975-0 Consists of the entire,000 our Service Kit (Part No. 499974-0), plus the following: Compressor Belt (Part No. 70-0) Cummins M 6 kw (50 BP) Diesel 00 our Part No. 49506-0 Consists of the following: Engine Water Filter (Part No. 464-0) Fuel Filter (Part No. 46-0) Engine Oil Filter (Part No. 469-0) Air Filter (Part No. 440-0),000 our Part No. 49506-0 Consists of the entire 00 our Service Kit (Part No. 49506-0), plus the following: ydraulic Filter in Tank (Part No. 4677-0) Filter, Breather (Part No. 9066-) Two each ydraulic Filters - Spin on (Part No. 97050-),000 our Part No. 49506-0 Consists of the entire,000 our Service Kit (Part No. 49506-0), plus the following: Alternator Belt (Part No. 46-0) Fan Belt (Part No. 46-0) ydraulic Test Kit Part No. 49979-6 Protect your investment by demanding Genuine Manitowoc Parts Service Kits. The ydraulic Service Kit consist of the following: All hydraulic fittings to access all pressures and flows ydraulic flow meters and pressure gauges to record hydraulic data. Electrical Break out harnesses to access voltages on all electrical circuits on all machines. Fluke Digital volt ohm meter, as used in all Manitowoc service literature. ydraulic Test Kit with case Part No. 49979-9 The above kit (Part No. 49979-6) plus a custom heavyduty carrying case. U.S. Standard Tools Kit Part No. 05- All standard tools needed to properly maintain and service your crane. (Does not include torque wrench.)
SM CraneCARE Field Service Factory-trained service experts are always ready to help maintain your crane s peak performance. For a worldwide listing of dealer locations, please consult our website at: www.manitowoccranes.com Technical Support Manitowoc s dealer network and factory personnel are available 4 hours a day, 7 days a week, 65 days a year to answer your technical questions and more, with the help of computerized programs that simplify crane selection, lift planning, and ground-bearing calculations. For a worldwide listing of dealer locations, please consult our website at: www.manitowoccranes.com Available from your Authorized Manitowoc Cranes Distributor, these VS videos are available in NTSC, PA and SECAM formats. Model Assembly Video Part No. 89980-0 Model Operation Video Part No. 89980-0 Model ubrication Video Part No. 899804-0 Your Capacity Chart Video Part No. 89977 Respect the imits Video Part No. 89974 Crane Safety Video Part No. 89976 Inspection/Repair Video Part No. 89978 5 Technical Documentation Manitowoc has the industry s most extensive documentation, and the easiest to understand, available in major languages and formats that include print, disk, and videotape. A complete set of Operator s, Parts, Capacity, Vendor, and Service Technician s Manuals are shipped with each crane. Additional copies available through your Authorized Manitowoc Distributor. Crane Operator s Manual Part No. 8997 Crane Parts Manual Part No. 89970 Crane Capacity Manual Part No. 89970 Crane Vendor Manual Part No. 8997 Service Technician s Manual (EPIC) Part No. 8997 CD rom versions of the Operator s and Parts Manuals are shipped with each crane. Also available are the following CDs: Maintenance Operation Service Parts (MOPS) CD Part No. 899800-0 Ground Bearing Pressure Estimator CD Part No. 899765-0 Crane Selection and Planning Software (CompuCRANE ) CD Part No. 899766-0 Capacity Chart (all EPIC models) CD Part No. 89980-0 Manitowoc Electronic Sales Assistant (MESA) CD Part No. 899798-0
Backed by Manitowoc CraneCARE SM CraneCARE is Manitowoc s comprehensive service and support program. It includes classroom and on-site training, prompt parts availability, expert field service, technical support and documentation for every one of the more than 7,000 Manitowoc cranes currently in use throughout the world. That s commitment you won t find anywhere else. That s CraneCARE. Manitowoc Cranes, Inc. P.O. Box 70 Manitowoc, WI, USA 54-0070 Telephone 90-684-66 Facsimile 90-68-677 www.manitowoccranes.com PRODUCT IMPROVEMENTS MAY CANGE SPECIFICATIONS 000 MANITOWOC 0500--PG-US 8-/ x -E-5000