FEATURES...5 to...5 bar,...5 to...5 psi gage 1 For corrosive media in harsh environments 1...6 or... ma output Field interchangeable All welded stainless steel diaphragm construction MEDIA COMPATIBILITY Wetted materials: Stainless steel 1. (16) Housing: Stainless steel 1.5 (), protection class IP 65 (according to DIN EN 659) respectively NEMA X 1 SPECIFICATIONS 8,9 Maximum ratings Supply voltage (reverse polarity protection) BTE(M)/PTE...G1... 1... BTE(M)/PTE...G... 1...6 Maximum load current BTE(M)/PTE...G1... only Temperature limits Storage Operating Media Compensated Humidity limits ibration (5 to 5 Hz) Mechanical shock Proof pressure BTEM5... PTE5... all others ma -55...1 C -...1 C -...15 C...7 C...1 %RH g 5 g 1 mbar 15 psi x rated pressure ELECTRICAL CONNECTION 1...6 output version Sensor... ma output version Sensor +s 1 Case +s 1 Case GND R L 1 to 1 to 6 GND 1/6
COMMON PERFORMAE CHARACTERISTICS 1 C haracteristics M in. T yp. Max. Unit Repeatability ±. 1 5 Long term stability ±. Output noise ±. Non-linearity and hysteresis ( BSL) ±. ±. 5 %FSO Thermal effects ( to 7 C) BTEM.../PTE5... ±. 6 ±. 5 ( combined offset and span) all others ±. 5 ±1. 5 (- to C, 7 to 1 C) ±. Frequency response (1 to 9 %) 1 ms Power supply rejection Offset.5 Span. %FSO/ INDIIDUAL PERFORMAE CHARACTERISTICS 1 1...6 output version ( S = 15, t amb = 5 C, R L > 1 kohm) C haracteristics M in. T yp. Max. Unit Zero pressure offset.9 1. 1.1 scale span.95 5. 5.5 scale output 6. Output impedance 5 Ω Power consumption (no load) 1 mw... ma output version ( S = 15, t amb = 5 C, R L = 1 Ohm) C haracteristics M in. T yp. Max. Unit Zero pressure offset. 9.. 1 scale span 15. 9 16. 16. 1 ma scale output. Power consumption (I = ma) L 6 mw /6
Specification notes: 1. IP 65 protection is given when the connector is locked. For proper function the gage port is vented to the atmosphere through the connector/cable assembly. Thus the cable end must have access to the ambient pressure.. The minimum supply voltage is directly proportional to the load resistance seen by the transmitter. For more details see the load limitation diagram.. Proof pressure is the maximum pressure which may be applied without causing damage to the sensing element.. Thermal effects tested and guaranteed from to 7 C relative to 5 C. All specifications shown are relative to 5 C. 5. Long term stability is the change in output after one year or 1 million pressure cycles. 6. Non-linearity refers to the Best Straight Line fit measured for offset, full scale span and 1/ full scale span. 7. Tests are in accordance with EN 61-6-. 8. CE-labelling is in accordance with /18/EC. 9. The pressure transmitters must not be used as safety accessories according to article 1,.1. of the directive 97//EC. ELECTROMAGNETIC CAPABILITY 7 Radiated, radio frequency electromagnetic field immunity (RFI) Electrical fast transient / burst immunity (EFT) Electrostatic discharge immunity test (ESD) Immunity to conducted disturbances induced by radio-frequency fields EN61--: EN61--: EN61--: EN61--6: Test conditions 1 /m, 8 to 1 8 % AMC (1 khz) ± k MHz ± k, contact discharge ±8 k, air discharge.15 to 8 MHz 1, 8 % AMC (1 khz) Criterion A B B A Interference OUTPUT CHARACTERISTIC 1...6 output version 6 5 1... ma output version Iout 16 ma 1 8 6 8 1 % full scale pressure 6 8 1 % full scale pressure /6
LOAD LIMITATION... ma output version 1 Ohm 1 8 6 operating range 1 supply RECOMMENDED ACCESSORY (included in delivery) ZK11: Connector/cable assembly (different cable lenghts available) 6.5 NOM m (other cable lenghts on request) NOM 6 Shield ent tube Pin PIN CONNECTION Flying lead end 1 Brown Green White and shield Yello w M1x1 Ø Note: For proper function of all gage devices the vent tube must have access to the ambient atmosphere. dimensions in mm /6
OUTLINE DRAWING Connector version. (1.) NOM 7. (.76) 5. (1) NOM 56. (.) M1 x 1 vent hole 1 /8" NPT mass: typ. 19 g WARNING Do not touch diaphragm WARNING: Do not use case to tighten pressure connection Pin 1 1...6 +s Case OUTPUT... ma +s Case Cable version. (1.) 5. (1) NOM 7. (.87) NOM 56. (.) 1 m SHIELDED CABLE x.5 mm² /8" NPT WARNING Do not touch diaphragm WARNING: Do not use case to tighten pressure connection Lead color 1...6 OUTPUT... ma bare brown white green yellow shield +s shield +s mass: typ. 19 g dimensions in mm (inches) 5/6
OPTIONAL PIPE FITTING DRAWINGS Part No. Male T1 Thread Male T W Hex in. D mm. in. R mm. Maximum working pressure (psig) SFIT6 SFIT6 SFIT68 /8 NPT /8 NPT /8 NPT 1/8 NPT 1/ NPT 1/8 BSP / / / 1.7 1.5 1.5. 7. 7..56/.8.56.56 1./9.7 1. 1. 7 7 7 Material: stainless steel 16 ORDERING INFORMATION BTE/PTE (M) xxx G x x Calibration BTE: mbar/bar calibration PTE: psi calibration For mbar ranges only Pressure range BTE series PTE series 5:...5 mbar 5:...5 psi 1:...1 bar 15:...15 psi :... bar :... psi 5:...5 bar 1:...1 psi 1:...1 bar :... psi :... bar 5:...5 psi 5:...5 bar 5:...5 bar Electrical connection A: Connector version C: Cable version Output signal 1: 1...6 :... ma Pressure mode G: gage pressure 1 Other pressure ranges and options are widely available. Please contact Sensortechnics. Sensortechnics reserves the right to make changes to any products herein. Sensortechnics does not assume any liability arising out of the application or use of any product or circuit described herein, neither does it convey any license under its patent rights nor the rights of others. 6/6