DIN DIN 13-5 DIN 13-6 ISO general purpose metric screw threads Part 5: Nominal sizes for 1 mm and 1.25 mm fi ne pitch threads; nominal diameter from 7.5 mm to 200 mm ISO general purpose metric screw threads Part 6: Nominal sizes for 1.5 mm fi ne pitch threads; nominal diameter from 12 mm to 300 mm DIN 13-7 ISO general purpose metric screw threads Part 7: Nominal sizes for 2 mm fi ne pitch threads; nominal diameter from 17 mm to 300 mm DIN 259 Whitworth pipe threads parallel internal and parallel external threads basic sizes Replaced by DIN EN ISO 228-1 DIN 2353 Non-soldering compression fi ttings with cutting ring Complete fi ttings and survey DIN 2445-2 Seamless steel tubes for dynamic loads Part 2: Steel tubes for precision application in fl uid systems, 100 bar to 500 bar DIN 2999-1 Whitworth pipe threads for threades pipes and fi ttings parallel internal threads and taper external threads thread dimensions Replaced by DIN EN 10226-1 DIN 3387-1 Separable unthreaded pipe connections for metal gas pipes Part 1: Connections for pipes with smooth ends DIN 3389 DIN 3850 DIN 3852-1 DIN 3852-2 Isolating joints ready for installation into service pipes in gas and water supply; built-in-isolating joints; requirements and tests Compression fi ttings Summary Stud ends, ports, for fi ttings, valves Part 1: Plug screw with metric fi ne pitch thread; General outlay of types Stud ends, ports, for fi ttings, valves Plug screw with Whitworth pipe thread General outlay of types DIN 3852-11 Screwed stud-ends; tapped holes; for compression fi ttings, valves, screw plugs, screwed stud-ends type E; design dimensions DIN 3853 Non-soldering and soldering compression fi ttings Stud ends for use with union nut; Design sheet DIN 3854 DIN 3858 DIN 3859-1 DIN 3859-2 DIN 3861 Non-soldering and soldering compression couplings Tapped holes for socket unions Construction sheet Whitworth pipe threads for pipe unions Parallel internal thread and taper external thread Dimensions Compression couplings Part 1: Technical delivery conditions Compression couplings Part 2: Assembly instruction for non-soldering compression couplings with cutting rings according DIN 2353 and DIN EN ISO 8434-1 Non-soldering compression fi ttings Compression rings Design DIN 3866 Refrigeration; threaded stem; 90 fl ared fl anges for solderless compression couplings rated for PN 40 DIN 3869 DIN 4755 DIN 4811 DIN 4815-1 Profi l sealing rings Oil fi ring installations Technical regulation for oil fi ring installation (TRÖ) Testing Pressure regulators for LPG and safety devices Requirements Rubber and plastics hoses for liquefi ed petroleum gas Part 1: Hoses and tubings 1 2011 / Errors and Misprints excepted
DIN 4815-2 DIN 4815-4 DIN 4817-1 DIN 7603 DIN 30660 DIN 30693 Rubber and plastics hoses for liquefi ed petroleum gas Part 2: Hose assemblies Hoses for LPG; hoses and hose assemblies for fuel gas installations in vehicles Shut off valves for liquefi ed gases; defi nitions, requirement, testing, marking Sealing rings Sealing materials for gas and water supply as well as water heating systems Non-hardening jointing compounds and polytetrafl uoroethylene (PTFE) tapes for metallic threaded joints in domestic installations Safety devices against rupture of fl exible tubes for LPG DIN EN DIN EN 331 DIN EN 417 DIN EN 449 DIN EN 549 DIN EN 560 DIN EN 731 Manually operated ball valves and closed bottom taper plug valves for gas installations for buildings Non-refi llable metallic gas cartridges for liquefi ed petroleum gases, with or without a valve, for use with portable appliances Construction, inspection, testing and marking Specifi cation for dedicated liquefi ed petroleum gas appliances Domestic fl ue less space heaters (including diffusive catalytic combustion heaters); Rubber materials for seals and diaphragms for gas appliances and gas equipment; Gas welding equipment Hose connections for equipment for welding, cutting and allied processes Gas welding equipment Air-aspirated hand blowpipes Specifi cations and tests; DIN EN 751-1 Sealing materials for metallic threaded joints in contact with 1st, 2nd and 3rd family gases and hot water Part 1: Anaerobic jointing compounds DIN EN 751-2 Sealing materials for metallic threaded joints in contact with 1st, 2nd and 3rd family gases and hot water Part 2: Non-hardening jointing compounds DIN EN 751-3 Sealing materials for metallic threaded joints in contact with 1st, 2nd and 3rd family gases and hot water Part 3: Unsintered PTFE tapes DIN EN 1057 Copper and copper alloys Seamless, round copper tubes for water and gas in sanitary and heating applications DIN EN 1949 DIN EN 10088-1 DIN EN 10088-3 Specifi cation for the installation of LPG systems for habitation purposes in leisure accommodation vehicles and accommodation purposes in other vehicles Stainless steels Part 1: List of stainless steels Stainless steels Part 3: Technical delivery conditions for semi-fi nished products, bars, rods, wire, sections and bright products of corrosion resisting steels for general purposes DIN EN 10226-1 DIN EN 10226-2 DIN EN 10305-1 Pipe threads where pressure tight joints are made on the threads Part 1: Taper external threads and parallel internal threads Dimensions, tolerances and designation Pipe threads where pressure tight joints are made on the threads Part 2: Taper external threads and taper internal threads Dimensions, tolerances and designation Steel tubes for precision applications Technical delivery conditions Part 1: Seamless cold drawn tubes 2 2011 / Errors and Misprints excepted
DIN EN 10305-2 DIN EN 10305-3 DIN EN 10305-4 DIN EN 10305-6 DIN EN 12449 DIN EN 12514-1 Steel tubes for precision applications Technical delivery conditions Part 2: Welded cold drawn tubes Steel tubes for precision applications Technical delivery conditions Part 3: Welded cold sized tubes Steel tubes for precision applications Technical delivery conditions Part 4: Seamless cold drawn tubes for hydraulic and pneumatic power systems Steel tubes for precision applications Technical delivery conditions Part 6: Welded cold drawn tubes for hydraulic and pneumatic power systems Copper and copper alloys Seamless, round tubes for general purposes Installations for oil supply systems for oil burners Part 1: Safety requirements and tests; parts, oil feed pumps, control and safety devices, supply tanks DIN EN 12514-2 Parts for supply systems for consuming units with liquid fuels Part 2: Safety requirements and tests Feed pumps, control and safety devices, service vessels DIN EN 12864 DIN EN 13153 Low-pressure, non adjustable regulators having a maximum outlet pressure of less than or equal to 200 mbar, with a capacity of less than or equal to 4 kg/h, and their associated safety devices for butane, propane or their mixtures Specifi cation and testing of LPG cylinder valves. Manually operated. DIN EN 13175 DIN EN 13349 DIN EN 13785 DIN EN 13786 DIN EN 13953 DIN EN 14071 DIN EN 14291 DIN EN 14543 DIN EN 14570 DIN EN 15202 LPG equipment and accessories Specifi cation and testing for Liquefi ed Petroleum Gas (LPG) tank valves and fi ttings Copper and copper alloys Pre-insulated copper tubes with solid covering Regulators with a capacity of up to and including 100 kg/h, having a maximum nominal outlet pressure of up to and including 4 bar, other than those covered by EN 12864 and their associated safety devices for butane, propane or their mixtures Automatic change-over valves having a maximum outlet pressure of up to and including 4 bar with a capacity of up to and including 100 kg/h, and their associated safety devices for butane, propane or their mixtures LPG equipment and accessories Pressure relief valves for transportable refi llable cylinders for Liquefi ed Petroleum Gas (LPG) Pressure relief valves for LPG tanks Ancillary equipment Foam producing solutions for leak detection on gas installations Specifi cation for dedicated liquefi ed petroleum gas appliances Parasol patio heaters Flue less radiant heaters for outdoor or amply ventilated area use Equipping of LPG tanks overground and underground LPG equipment and accessories Essential operational dimensions for LPG cylinder valve outlet and associated equipment connections DIN EN ISO DIN EN ISO 228-1 Pipe threads where pressure-tight joints are not made on the threads Part 1: Dimensions, tolerances and designation (ISO 228-1:2000) DIN EN ISO 1127 Stainless steel tubes - Dimensions, tolerances and conventional masses per unit length (ISO 1127:1992) 3 2011 / Errors and Misprints excepted
DIN EN ISO 1179-1 DIN EN ISO 1179-2 DIN EN ISO 1179-3 DIN EN ISO 1179-4 DIN EN ISO 6149-1 Connections for general use and fl uid power Ports and stud ends with ISO 228-1 threads with elastomeric or metal-to-metal sealing Part 1: Threaded ports (ISO 1179-1:2007) Connections for general use and fl uid power Ports and stud ends with ISO 228-1 threads with elastomeric or metal-to-metal sealing Part 2: Heavy-duty (S series) and light-duty (L series) stud ends with elastomeric sealing (type E) (ISO 1179-2:2007) Connections for general use and fl uid power Ports and stud ends with ISO 228-1 threads with elastomeric or metal-to-metal sealing Part 3: Light-duty (L series) stud ends with sealing by O-ring with retaining ring (types G and H) (ISO 1179-3:2007) Connections for general use and fl uid power Ports and stud ends with ISO 228-1 threads with elastomeric or metal-to-metal sealing Part 4: Stud ends for general use only with metal-to-metal sealing (type B) (ISO 1179-4:2007) Connections for hydraulic fl uid power and general use Ports and stud ends with ISO 261 metric threads and O-ring sealing Part 1: Ports with truncated housing for O-ring seal (ISO 6149-1:2006) DIN EN ISO 6149-2 DIN EN ISO 6149-3 Connections for hydraulic fl uid power and general use Ports and stud ends with ISO 261 metric threads and O-ring sealing Part 2: Dimensions, design, test methods and requirements for heavy-duty (S series) stud ends (ISO 6149-2:2006) Connections for hydraulic fl uid power and general use Ports and stud ends with ISO 261 metric threads and O-ring sealing Part 3: Dimensions, design, test methods and requirements for light-duty (L series) stud ends (ISO 6149-3:2006) DIN EN ISO 6806 Rubber hoses and hose assemblies for use in oil burners Specifi cation (ISO 6806:1992) DIN EN ISO 8434-1 Metallic tube connections for fl uid power and general use Part 1: 24 degree cone connectors (ISO 8434-1:2007) DIN EN ISO 10239 Small craft Liquefi ed petroleum gas (LPG) systems (ISO 10239:2008) DIN EN ISO 19879 Metallic tube connections for fl uid power and general use Test methods for hydraulic fl uid power connections (ISO 19879:2005) DIN ISO DIN ISO 261 ISO general purpose metric screw threads General plan (ISO 261:1998) DIN ISO 12151-2 Connections for hydraulic fl uid power and general use Hose fi ttings Part 2: Hose fi ttings with ISO 8434-1 and ISO 8434-4 24 cone connector ends with O-rings (ISO 12151-2:2003) DVGW DVGW G 260 DVGW G 607 DVGW G 608 DVGW G 612 DVGW GW 392 Technical directive G 260: gas condition Technical directive G 607: LPG installations for habitation purposes in leisure accommodation vehicles and accommodation purposes in other vehicles Operating and testing Technical directive G 608: Small craft Liquefi ed petroleum gas (LPG) systems Technical directive G 612: Operation of moveable LPG systems for leisure purposes for outdoor use Technical directive GW 392: Seamless copper pipes for gas and drinkable water installations and seamless, internally tin-coated copper pipes for drinkable water installations requirements and testing TRGI Technical directive G 600 for natural gas installations (DVGW-TRGI 2008) 4 2011 / Errors and Misprints excepted
DVGW VP DVGW VP 103 DVGW VP 202 Requirements and testing of LPG hand torches LPG pressure regulating devices with a nominal inlet pressure of 50 mbar for gas appliances in vehicles DWA A DWA A 791 Standard DWA-A 791 Fuel oil consuming units EG-Richtlinien 89/106/EEC 94/9/EC 97/23/EC 2004/78/EC 2004/108/EC 2006/95/EC 2009/142/EC Council Directive 89/106/EEC of 21 December 1988 on the approximation of laws, regulations and administrative provisions of the Member States relating to construction products Construction Products Directive CPD Directive 94/9/EC of the European Parliament and the Council of 23 March 1994 on the approximation of the laws of the Member States concerning equipment and protective systems intended for use in potentially explosive atmospheres ATEX Directive 97/23/EC of the European Parliament and of the Council of 29 May 1997 on the approximation of the laws of the Member States concerning pressure equipment Pressure Equipment Directive PED Directive 2004/78/EC of 29 April 2004 amending Directive 2001/56/EC of the European Parliament and of the Council relating to heating systems for motor vehicles and their trailers and Council Directive 70/156/EEC for the purposes of adapting to technical progress Directive 2004/108/EC of the European Parliament and of the Council of 15 December 2004 on the approximation of the laws of the Member States relating to electromagnetic compatibility and repealing Directive 89/336/EEC Directive 2006/95/EC of the European Parliament and of the Council of 12 December 2006 on the harmonisation of the laws of Member States relating to electrical equipment designed for use within certain voltage limits Low Voltage Directive LVD Directive 2009/142/EC of the European Parliament and of the Council of 30 November 2009 relating to appliances burning gaseous fuels Gas Appliance Directive GAD ISO ISO 7-1 Pipe threads where pressure-tight are made on the threads Part 1: Designation, dimesions and tolerances NF M 88-768 NF M 88-768 Liquifi ed hydrocarbon installations Flexible couplings for gas phase pren pren 12514-1 Parts for supply systems for consuming units with liquid fuels Part 1: Safety requirements and tests Terminology, general requirements pren 12514-3 Parts for supply systems for consuming units with liquid fuels Part 3: Safety requirements and tests Valves and meters pren 12514-4 Parts for supply systems for consuming units with liquid fuels Part 4: Safety requirements and tests Pipings and parts within pipelines 5 2011 / Errors and Misprints excepted
TRB TRB 600 Installation of pressure vessels TRF TRF TRF 1996 Technische Regeln Flüssiggas, technical directions for the installation of LPG TRÖl TRÖl Technische Regeln Ölanlagen, technical directions for the installation of oil ANSI/ASME ANSI/ASME B1.20.1 Pipe threads, general purpose (inch) 6 2011 / Errors and Misprints excepted