Directionl Control Vlves Solenoid Operted with 8W Coil RPEA3-06 0/20 Size 06 (D 03) 350 br (5076 PSI) 80 L/min (2 GPM) Replces 2/2007 /3-, /2- wy directionl control vlves Enclosure type to IP65 Push button mnul override Instlltion dimensions to DIN 2 30 / ISO 0 / CETOP RP2-H Subpltes see dt sheet HA 0002 Functionl Description The RPEA3 directionl control vlves consist of housing (), control spool (5) with two centering springs (), cylindricl operting solenoids (2, 3), electric wirebox (9) nd connector (6). The three-position directionl control vlves re fitted with two solenoids nd two springs. Two-position directionl control vlves hve either one solenoid nd one return spring or two solenoids nd detent ssembly. The solenoids re supplied with DC voltge through the Ports on the wirebox optionl on both sides or through Connector Item (5 - Pin) M2, see wiring digrm (pge 6). The wires re connected to terminl plte inside the wirebox. Optionl lights re instlled on this terminl plte for shift indiction. The lights re visible s rised rrows on the vlve lbel. The solenoids re retined by the Nut (7) nd plug-in to the wirebox. Plug -in design llows esy removl without wire chnge. In the cse of solenoid mlfunction or power filure, the spool of the vlve cn be shifted by mnul override (8), provided the pressure in T- port does not exceed 25 br (362,5 PSI). The vlve housing () is phosphte coted nd the solenoids (2, 3) re zinc coted. T P A B
Ordering Code RPEA3-06 / Solenoid - Operted Directionl Control Vlves with 8W Coil Solenoid identifiction no designtion stndrd ISO US Stndrd ANSI-B93.9 A Nominl Size no designtion V Sels NBR FPM (Viton) Number of Vlve Positions two positions 2 three positions 3 no designtion D D2 D3 D D5 Orifice in P Port without orifice.0 mm (0.039 in).5 mm (0.059 in) 2.0 mm (0.079 in) 2.2 mm (0.087 in) 2.5 mm (0.098 in) Spool Symbols see the tble spool symbols no designtion N N2 Mnul Override stndrd covered with retining nut covered with rubber boot Rted Supply Voltge of Solenoids 2 V DC / 0.33 A 0200 Wirebox Configurtions Type of Solenoid Coil for Wiring Box (Plug-In-Coil) DC solenoid 8W EW 63 Wiring box with 5 PIN connector M2 mounted on A-side (B-side pluged) 6 Wiring box with 5 PIN connector M2 mounted on B-side (A-side pluged) 65 Wiring box with 5 PIN connector M2 mounted on A-side with LED diode (B-side pluged) Type of Wirebox Wirebox for DC nd AC K 66 Wiring box with 5 PIN connector M2 mounted on B-side with LED diode (A-side pluged) 2
Technicl Dt Vlve size mm (US) 06 (D 03) Mximum flow L/min (GPM) see p-q chrcteristics Mx. operting pressure t porte P, A, B br (PSI) 350 (5076) Mx. operting pressure t port T br (PSI) 20 (3000) Pressure drop br (PSI) see p-q chrcteristics Hydrulic fluid Hydrulic oils of power clsses (HL, HLP) to DIN 552 Fluid temperture rnge for NBR sels C ( F) -30... +80 (-22... +76) Fluid temperture rnge for FPM sels C ( F) -20... +80 (-... +76) Ambient temperture mx. C ( F) +50 (+22) Viscosity rnge mm 2 /s (SUS) 20... 00 (98... 80) Mximum degree of fluid contmintion Clss 2/8/5 to ISO 06 Mx. llowble voltge vrition % DC: 0 Mx. switching frequency h - 5 000 Switching time, on: t =32 mm 2 /s (56 SUS) ms DC: 30... 50 Switching time, off: t =32 mm 2 /s (56 SUS) ms DC: 0... 50 Duty cycle % 00 Service life cycles 0 7 Enclosure type to EN 60529 IP 65 Weigt - vlve with solenoid - vlve with 2 solenoids Mounting position kg (lbs),3 (2.9),9 (.2) unrestricted Functionl Symbols Type Symbol Crossover Type Symbol Crossover Note: Contrry to the Europen Norm, the US Stndrd ANSI-B93.9 sttes tht the solenoid routing on energizing the oil flow to port A be mrked with, nd the solenoid routing on energizing the oil flow to port B be mrked with b. This rule is vlid independently from the solenoid ly-out. 3
p-q Chrcteristics Mesured t = 32 mm 2 /s (56 SUS) Operting limits for mximum hydrulic power trnsferred by the directionl vlve. Operting pressure p [br (PSI)] -3 2 3 Flow Q [L/min (GPM) Z C P Y R P5 Z5 C5 X Y5 3 2 3 2 p-q Chrcteristics Mesured t = 32 mm 2 /s (56 SUS) Pressure drop p relted to flow rte. Pressure drop p [br (PSI)] 3 2 P-A P-B A-T B-T P-T Z 2 2 2 2 C 2 2 2 2 3 P 2 2 Y 2 2 R 2 2 2 X 2 2 2 Z5 2 2 C5 2 2 3 P5 Y5 2 Flow Q [L/min (GPM)
Vlve Dimensions Vlve with two solenoids Dimensions in millimeters (inches) 2,5 (0.92) 0,5 (.593) 33 (.299) 30,2 (.89) 2,5 (0.853) 2,7 (0.50) 3 8 6 2 3 0,75(0.03) P 3 (.29) A T B 32,5 (.28) b 7 3, (0.528) 90 (3.53) 6,5 (2.2) 22,2 (0.87) M2x 9,5 (0.37) 5,3 (0.209) b 2 (0.95) 37,3 (.69) 9,3 73,5 (2.893) 9 (3.582) 72,5 (2.85) Vlve with one solenoid Spool symbols R, P5, Y5, Z5, C5 8 (0.35) 2,(0.88) 68 (2.59) 23 (8.386) Nut torque 2.66 fts-lb. (3,6 Nm) Solenoid * 2 Solenoid b* 3 Mnul override Nme plte 5 Squre ring ( pcs.) 0.36 x 0.66 (9.25 x.68 mm) supplied with vlve 6 mounting holes 7 Electricl connector 8 Pin hole 8,5 (5.86) 8 (0.35) *Note: On vlves with solenoid identifiction ccording to US Stndrd ANSI-B93.9 cn the solenoid designtion vry from this rngement, this is bsed on the function symbol. 0.000 /.0 [ in 0.0 / 00 [ mm [ [ 0,8(32) Rmx 6,3(28) [ m( in) ] Vlve with one solenoid b Spool symbols X, Z, C, Y, P Required surfce finish of interfce b 5
Mnul Override STANDARD CLOSED NUT No designtion Dimensions Type N (For DC voltge solenoids only) Dimensions 20 (0.787) 27,5 (.083) Stndrd model of the mnul override. Stndrd retining nut of the solenoid. Mnul override with retining nut. Cn be used fter removing nut. RUBBER BOOT Type N2 (For DC voltge solenoids only) Dimensions 3 (.22) Mnul override protected by rubber boot. Orifice in P-Port Type D mm (inch ) Dimensions Description D,0 (0.039) D2,5 (0.059) D3 2,0 (0.079) D 2,2 (0.087) D5 2,5 (0.098) Connector - M2 Sel ring P-Port orifices limit the flow into the directionl control vlve. Attention: When the orifice in P port is dditionlly mounted the stndrd used squre ring NBR is replced with O-ring from Viton. Pin - loction Vlve with 2 Mgnets Pin - loction Vlve with Mgnet 5 Mgnet Mgnet b Mgnet or b 5 +2 +2-3 + -3 + Note: On vlves with solenoid identifiction ccording to US Stndrd ANSI-B93.9 wiring will be different from bove: on vlves with one () solenoid lwys Pin 2 for the -Solenoid nd Pin for the b-solenoid. This is independent from the ctul physicl loction of the solenoid. 6
Spre prts 8 7 2 3 6 5 - Solenoid coil (DC solenoid) 2 - Mounting bolts 3 - Nut with sel (Nut torque 3 Nm (2.2Ibf) - Connector M2 5 - Sel kit 6 - Orifice in P port with sel ring 7 - Terminl plte 8 - Wiring box 7
Wiringbox Type Ordering number Wiring box without terminl plte 6203600 Terminl Pltes Type Ordering number Terminl plte 2V - preventive A+B 28572900 Terminl plte 2V - preventive A 2007600 Terminl plte 2V - preventive B 28572800 Terminl plte 2V - LED diode nd preventive A+B 2007700 Terminl plte 2V - LED diode nd preventive A 2007800 Terminl plte 2V - LED diode nd preventive B 28572800 Solenoid Coil Voltge rting Type Ordering number 2 V DC EW 20000 Solenoid Retining Nut with Sel Type of the nut Sel ring Ordering number Stndrd nut 58600 Closed nut (DC only) 22 x 2 58700 Nut with rubber boot (DC only) 58800 Electricl Connector M2 Type Ordering number Mle 5 PIN 2007900 Orifice in P-Port Type D mm (inch) Sel ring Ordering number D.0 (0.039) 585600 D2.5 (0.059) 585700 D3 2.0 (0.079) 9.25 x.75 585800 D 2.2 (0.087) 586000 D5 2.5 (0.098) 585900 Sel Kit Type Dimensions, quntity Ordering number Stndrd - NBR70 9.25 x.68 ( pcs.) 7 x.8 (2 pcs.) 9.25 x.75 ( pc) 283800 Viton 9.25 x.78 ( pcs.) 7.7 x.78 (2 pcs.) 58500 Bolt Kit (for studs see HU 0030) Dimensions, quntity Bolt torque Ordering number M5 x 5 DIN 92-0.9 ( pcs.) 8.9 Nm (6.6 Ibf) 58500 Cution! When the distributor contins two electromgnets ny of the two electromgnets cn be switched on only fter the other one switches off. Distributors with other interconnections thn those shown in the ctlogue cn be supplied on request. The pckging foil cn be recycled The trnsport bse plte cn be returned to the mnufcturer. Mounting screws M5 x 5 DIN 92-0.9 or bolts must be ordered seprtely. The screws tightening torque is 8.9 Nm (6.6 ft-ibs). The mentioned dt only serve to describe the product nd in no cse re to be understood in terms of lw s gurnteed chrcteristics. 8 ARGO-HYTOS s.r.o. CZ - 53 5 Vrchlbí Tel.: +20-99-03, Fx: +20-99-032 E-mil: sles.cz@rgo-hytos.com www.rgo-hytos.com Subject to ltertion without notice!