RAPID RESPONSE SYSTEM 2283 AIR CONTROL ACCESSORY KIT INSTALLATION INSTRUCTIONS Congratulations on your purchase of a new Air Control Accessory Kit. This kit was designed to provide inflation control of your air springs. This kit will be an asset to your vehicle, meeting your air supply needs. Please take a few minutes to read through the instructions, identify the components, and learn how to properly install your Air Control Accessory Kit. NOTE: The Air Control Accessory Kit can be used with most air spring products. If you are installing an air spring kit, do not install the air line tubing into the air springs as stated in the air spring manual. NOTE ON CONNECTING THE AIR LINE TUBING Cut the air line tubing as square as possible. To connect the air line tubing to the fittings, push the air line tubing into the fitting as far as possible. If for any reason the air line tubing must be removed, make sure the air springs are deflated, then push the collar of the fitting toward the body of the fitting and the air line tubing can be removed. To reassemble, make sure the air line tubing is cut square and push back into the fitting. STEP 1 - PREPARE THE COMPONENTS A) COMPRESSORS Install the threaded end of the T-fitting into the compressors head. Tighten the fitting sufficiently to engage the orange thread sealant. Next, install the pressure switch into the female end of the T-fitting, see Figure "A". PARTS LIST COMPRESSORS 9285 2 SOLENOID BLOCK 9221 1 AIR TANKS 9127 2 DUAL AIR CONTROL PANEL S.S. 1 PRESSURE SWITCH 100-150 9193 2 18 FT. 1/4" AIR LINE TUBING (BLACK) 9151 1 40 FT. 1/8" AIR LINE TUBING (BLACK) 9222 1 FT. 3/8" AIR LINE TUBING (BLACK) 9223 3 ELECTRICAL ASSEMBLY 9224 1 10-32 x 1" MACHINE SCREW 13 10-32 NYLON INSERT NUT 13 10-32 X 1-3/4 S.H.C.S. 2 3/8" -16UNC X 1" HEX BOLT 8 B) AIR TANKS Thread a 1/4" tube fitting and a 3/8" male push-to-connect tube fitting into either end of both air tanks, see Figure "A". Tighten the fittings securely to engage the orange thread sealant. STEP 2 - SELECT A MOUNTING LOCATION A) COMPRESSORS ATTACHMENT Begin by removing the negative battery cable. Select a convenient location to mount the compressors. This location should provide ample air flow and be protected from airborne debris and moisture. The mounting surface should be rigid to support the compressors, such as under the hood on a fender well or in a vented storage compartment. (Note: The compressors can be mounted in any orientation.) Using the compressor template, mark and drill three 3/16" holes. Any burrs in the holes should be removed to prevent damage to the rubber isolators. Mount the compressors using the #10-32 x 1" machine screws, #10-32 lock nuts, and #10 washers supplied with the kit see Figure "B". Maximum vibration isolation can be achieved by properly mounting the compressors. The machine screw and nut should be tightened only enough to bottom-out the brass insert see Figure "B". DO NOT OVER-TIGHTEN. Over-tightening will crush the brass insert and the insulator, thereby reducing vibration isolation. B) AIR TANK ATTACHMENT Select a location to mount the air tanks. This should be in a protected location to prevent damage from rocks or airborne debris. Using the tank feet as a template, mark and drill 3/8" holes. Bolt the air tanks in place using the 3/8" -16 x 1" hex bolts with the 3/8" -16 flanged lock nuts and 3/8" washers provided. Ensure that the installation allows unrestricted access to the air ports on the tanks. 3/8" -16 FLANGED NUT 8 3/8" FLAT WASHER 8 3/16" FLAT WASHER 20 COMPRESSORS T-FITTING 2 PUSH-TO-CONNECT 1/4NPT X 3/8 STR 8 PUSH-TO-CONNECT 1/8NPTM TO 1/8 TUBE 4 LEVEL COMMAND TEMPLATE 1 NYLON TIE 15 FT. 16 GAUGE WIRE 1 MALE CONNECTOR 04X04 2 FUSE 20 AMP SPADE TYPE 2 FUSE HOLDER SPADE TYPE 2 MALE SPADE TERMINAL 2 24-8291 08-04 NAD-33635
2283 Figure A Pneumatic Configuration Please Note: The Pneumatic Configuration displayed on this page is a general configuration for concept purposes only. Electrical Configuration 1/8 Tube TO +12V, 20 AMP POWER SOURCE 20 AMP FUSE RED MALE AIR FITTING AIR FILTER + Positive AIR FILTER MALE AIR FITTING Positive + Wire Harness 1/4 Tube 1/4 Tube AIR LINE AIR LINE -Ground Ground AIR LINE CONFIGURATION - - Ground L.F. L.R. R.F. R.R. INLET EXHAUST - Ground OUT TO AIR SPRINGS
BRASS SLEEVE COMPRESSOR FOOT RUBBER ISOLATOR C) GAUGE PANEL ATTACHMENT Select a mounting surface for the gauge panel in the dashboard of your vehicle or other protected location. Using the gauge panel as a template, center mark the mounting holes on the dashboard. Drill a 3/16" hole on each center mark. Do not attach the panel to the dashboard at this time. #10-32 LOCK NUT #10-32 x 1 PAN HEAD SCREW PLASTIC CONNECTOR CONNECTING WIRE Figure "B" #10 FLAT WASHER BRASS SLEEVE COMPRESSOR FOOT RUBBER ISOLATOR #10 FLAT WASHER EXISTING WIRE VEHICLE MOUNTING SURFACE STEP 3 - PREPARE AND MOUNT THE SOLENOID BLOCK Install four 1/8NPT fittings in one side of the solenoid block. Tighten the air fittings securely to engage the orange sealant. Install six 1/4 NPT 3/8 tube fittings in the other sides of the solenoid block as shown in Figure "A". Tighten the air fittings securely to engage the orange thread sealant. Select a location to mount the solenoid block. This should be in a protected location to prevent damage from rocks or airborn debris. Using the solenoid block as a template, mark and drill two 3/16" holes. Mount solenoid block with 10-32 x 1-3/4" socket head cap screw and nylock nuts and washers. STEP 4 - ROUTE THE ELECTRICAL HARNESS All the wires are color coded to aid in installation of this kit. Left Front Blue wire Left Rear Green wire Right Front White wire Right Rear Yellow wire Connect the wires from the solenoid block to the wiring harness by simply pushing the two pin connectors together until a clicking noise is heard. Then route the wiring harness to the control panel. Avoid routing the wiring harness next to direct heat from the engine, exhaust pipes and away from sharp edges. Then plug in each six pin connector to the back of the switches. You can choose which switch you would like to use on each air spring by the wire color codes. Figure "C" STEP 5 - ROUTE THE AIR LINE TUBING Please note: Do not fold or kink the air line tubing. A ragged or angled cut can cause a leak in the system. Push the air line tubing into the fitting as far as possible. FUSE HOLDER Avoid routing the air line tubing next to direct heat from the engine or exhaust pipe, and away from sharp edges. The air line tubing should not be bent or curved sharply as it may buckle with age. Secure the air line tubing in place with the nylon ties provided. Using the 1/4" air line tubing, measure the distance from the compressors to the air tanks. Cut the air line tubing accordingly, as squarely as possible. Push the air line tubing into the fittings as far as possible. Using the 1/8" air line tubing, measure the distance from the solenoid block to the control panel. Cut the air line Figure "D" tubing accordingly, as squarely as possible. The solenoid block is marked as to which air spring the gauge will read, see Figure "A". Using the 3/8" air line tubing, measure the distance from the solenoid block to each of the air springs. Cut the air line tubing accordingly, as squarely as possible. The solenoid block is marked as to which air spring each air line tubing goes to. Insert one end of the air line tubing into the fitting installed on the top of the air spring and insert the other end into the fitting in the solenoid block. Push the air line tubing into the fittings as far as possible. STEP 6 - ROUTE THE ELECTRICAL WIRE (COMPRESSOR) All necessary electrical wire and connectors have been included with this kit. Review the electrical schematic before beginning installation, see Figure "A". Secure the ring terminal to a grounded component of the chassis. Route a length of wire from the pressure switch to a positive 12 volt, 20 amp, ignition activated power source on the vehicle. Cut a length of 16 gauge wire from the 15' supply included with this kit. Install the female terminal connector from the compressor over the remaining spade on the pressure switch. Connect the lead from the pressure switch to the 12 volt wire with a wire connector. Slide the wire connector over the existing wire and insert the un-stripped lead from the pressure switch into the wire connector. Close the wire connector over both wires with pliers, see Figure "C". Install the in-line fuse holder in the positive pressure switch lead. Cut the pressure switch lead near the wire connector and insert
BACK OF GAUGE the un-stripped ends of the wire into the fuse holder. Close the fuse holder over the wires with pliers and install the fuse, see Figure "D". RING CONNECTOR (TO GROUND) POSITIVE WIRE (TO DASHBOARD ILLUMINATION WIRE) Figure "E" STEP 7 - WIRE THE GAUGE PANEL FOR ILLUMINATION There are two wires (one red and one black) attached to the gauge on the back of the control panel. Connect the red wire to a fused dashboard illumination wire. Conncet the black wire to a suitable ground source, see Figure "E". Attach the end of the positive wire to a dashboard illumination wire using a wire connector. Slip the wire connector over the existing dashboard illumination wire and insert the un-stripped gauge panel wire into the wire connector. Close the wire connector onto the wires with pliers, see Figure "C". Attach the black wire to a ground source by crimping a ring connector onto the wire and securing it to a suitable ground source on the vehicle. Note: Should additional wire be necessary to reach the dashboard illumination wire and ground source, use 18 gauge multi-strand wire. STEP 8 - ATTACH THE GAUGE PANEL Install the gauge panel on the dashboard where the holes were drilled in Step 2C. Attach the gauge panel to the dashboard or other mounting surface using the enclosed #10-32 x 1" machine screws, #10-32 lock nuts, and #10 washers. STEP 9 - TEST THE SYSTEM With the Air Control Accessory Kit and air springs installed, you are ready to test the system. Re-attach the negative battery cable. Turn on the ignition. The compressors will start and build pressure in the system. Push the paddle switch upward to inflate the air springs. The gauge will display how much air pressure is in the air springs. Inflate the air springs to 70 and check the fittings for air leaks with an applied solution of soap and water. If a leak is detected at a tubing connection, check to make sure that the tube is cut as square as possible and that it is pushed completely into the fitting. The tubing can easily be removed from the fitting by first releasing the pressure from the air spring, then by pushing the collar towards the body of the fitting and then pulling out the air line tubing. SYSTEM OPERATION The air control accessory kit allows the air springs to be inflated from the inside of the vehicle. Push the paddle switch up to inflate the air springs and down to deflate the air springs. This air accessory kit provides front-to-rear and side-to-side leveling.
Do Not Return This Product to the Dealer or Distributor If you are missing parts, experiencing installation problems, or have technical concerns regarding this product, you may contact a Firestone Technical Service Representative at rrtech@fsip.com or at -888-0650 (option 1, and then option 2). Representatives are available from 7: a.m. 4: p.m. Eastern on Monday Friday, excluding holidays. If you are located outside of the United States, you should first contact your distributor or dealer directly with any issues. When contacting Technical Service, please have the kit or part # ready, along with the make, model, and year of the vehicle. You may also need to provide details, such as 2WD/4WD or if the vehicle has been lifted or lowered from stock height. If you have a warranty concern, please include in your email a detailed description of the situation, a photo(s) of the issue, and your contact information, including ship-to address. WARRANTY COVERAGE* The Ride-Rite kits, components, and accessories are warranted against defects in workmanship and materials. This warranty does not cover service or labor charges, neglect to the product. Ride-Rite air springs Lifetime Limited Sport-Rite air springs Lifetime Limited Coil-Rite air springs Lifetime Limited Level-Rite air springs Lifetime Limited PERIOD OF COVERAGE: Work-Rite load assists 2 Years Limited Air-Rite accessories 2 Years Limited Brackets, hardware, fittings, air line, and other components 2 Years Limited HOW TO MAKE A WARRANTY CLAIM If you purchased your air springs in the U.S. or Canada and believe you have a part with a warrantable defect, call Firestone directly at 1--888-0650. International customers should contact their distributors or dealers directly with any problems. (*) Please refer to the Firestone Limited Lifetime Air Spring Warranty for details, terns, and conditions. 21-8387 01-13 NAD-37143-1
FIRESTONE LIMITED LIFETIME AIR SPRING WARRANTY Firestone Industrial Products Company LLC ( Firestone ) warrants that its Ride Rite Air Spring Assembly will perform according to the manufacturer s specifications for as long as the vehicle on which the system was originally installed is owned by the original retail purchaser. This limited warranty does not include installation or other service charges for replacement. Warranty Period The Air Spring is warranted for as long as the original purchaser owns the vehicle on which it was originally installed. The fasteners and upper and lower brackets which accompany the air spring are warranted for a period of twenty-four (24) months or 24,000 miles whichever occurs first. This warranty begins on the original retail delivery date. What is Covered Any implied warranties are limited in duration to the coverage period of this warranty (some states do not allow limitation on how long an implied warranty lasts so the above limitation may not apply to you). This Warranty runs in favor of the original retail purchaser when the Ride Rite Air Spring Assembly is used under normal operating conditions according to Firestone s specifications and installed on the appropriate application. This warranty does not apply to Ride Rite Air Spring Assemblies that have been improperly applied, improperly installed, used in racing or off road applications or used for commercial purposes. In addition, the warranty will not apply to products which have not been maintained and serviced according to the instructions that accompany the air spring assembly. The consumer will be responsible for any costs incurred in removing the product from the vehicle and the cost to return the air spring assembly to the dealer or installer from which it was purchased. If it is determined that the Ride Rite Air Spring Assembly failed as a result of a manufacturing defect, Firestone will repair or replace, at its option, any product or components subject to this warranty. You should retain a copy of your contract with your installer and your receipt as proof of the date of installation. This warranty is non-transferable and is not assignable in any way. Firestone specifically excludes any obligation for consequential damages or incidental expenses including claims for loss of use of the product, loss of time, inconvenience, or commercial loss. This warranty gives you specific legal rights. You may also have other rights that may vary from state-to-state. Some states do not allow limitations on how long an implied warranty lasts or allow the exclusion or limitation of incidental or consequential damages. The above limitation or exclusion may not apply to you. There are no warranties, express or implied, including implied warranty of merchantability and fitness which extend beyond this warranty.