ALLDATA Online - 2001 Chevy Truck S10/T10 Blazer 2WD V6-4.3L VIN W - Intake... Page 1 of 21 Home Account Contact ALLDATA Log Out Help PAUL REDEHOFT Select Vehicle New TSBs Technician's Reference Component Search: OK 2001 Chevy Truck S10/T10 Blazer 2WD V6-4.3L VIN W Conversion Calculator Vehicle Level Engine, Cooling and Exhaust Engine Intake Manifold Service and Repair Intake Manifold Replacement (Upper) Intake Manifold Replacement (Upper) Notes Intake Manifold Replacement - Upper Removal Procedure Important: The upper intake does not have to be removed to remove the lower intake manifold. 1. Disconnect the breather tube at the air cleaner outlet duct.
ALLDATA Online - 2001 Chevy Truck S10/T10 Blazer 2WD V6-4.3L VIN W - Intake... Page 2 of 21 2. Remove the air cleaner outlet duct retaining wingnut. 3. Disconnect the IAT sensor harness connector.
ALLDATA Online - 2001 Chevy Truck S10/T10 Blazer 2WD V6-4.3L VIN W - Intake... Page 3 of 21 4. Remove the air cleaner outlet duct from the throttle body. 5. Disconnect the accelerator cable from the throttle body.
ALLDATA Online - 2001 Chevy Truck S10/T10 Blazer 2WD V6-4.3L VIN W - Intake... Page 4 of 21 6. Remove the accelerator cable from the accelerator control cable bracket. 7. Disconnect the cruise control cable, if equipped from the throttle shaft and the accelerator cable bracket. 8. Disconnect the vacuum hose from the intake manifold for the vacuum tank. 9. Remove the power brake booster vacuum hose.
ALLDATA Online - 2001 Chevy Truck S10/T10 Blazer 2WD V6-4.3L VIN W - Intake... Page 5 of 21 10. Disconnect the following electrical connectors: The A/C compressor clutch (1) The A/C compressor cutoff switch (5), if equipped The Throttle Position (TP) sensor (2) The Idle Air Control (IAC) motor (3) 11. Disconnect the following electrical connectors: The fuel meter body assembly (1) The Manifold Absolute Pressure (MAP) sensor(3) The EVAP canister purge solenoid valve (2)
ALLDATA Online - 2001 Chevy Truck S10/T10 Blazer 2WD V6-4.3L VIN W - Intake... Page 6 of 21 12. Remove the engine wire harness clip from the accelerator cable bracket. 13. Move the engine wiring harness aside. 14. Remove the accelerator cable bracket from the throttle body and the intake manifold. 15. Remove the accelerator and cruise control cable bracket from the throttle body. Leave the accelerator and cruise control cables on the bracket.
ALLDATA Online - 2001 Chevy Truck S10/T10 Blazer 2WD V6-4.3L VIN W - Intake... Page 7 of 21 16. Remove the PCV valve hose assembly from the intake manifold and the valve rocker arm cover. 17. Remove the bracket for the engine wiring harness from the intake manifold stud. 18. Remove the fuel lines from the fuel meter body assembly. 19. Remove the EVAP canister purge solenoid valve.
ALLDATA Online - 2001 Chevy Truck S10/T10 Blazer 2WD V6-4.3L VIN W - Intake... Page 8 of 21 20. Remove the studs for the upper intake manifold, 21. Remove the upper intake manifold. 22. Remove the upper intake manifold gasket from the groove. 23. Discard the gasket.
ALLDATA Online - 2001 Chevy Truck S10/T10 Blazer 2WD V6-4.3L VIN W - Intake... Page 9 of 21 24. Remove the seal from the fuel meter body assembly. 25. Discard the seal. Important: Do not immerse the assembled upper intake manifold in cleaning solvent. 26. Clean all sealing surfaces and the inside of the upper intake manifold with a shop towel and cleaning solvent. 27. Inspect the upper intake manifold for the following: Cracks or other damage to the exterior Cracking or damage to the gasket grooves Loose or damaged bolt hole thread inserts Damage to the throttle body mounting surface
Page 10 of 21 28. If replacing the upper intake manifold, turn and remove the power brake booster vacuum tube fitting from the upper intake manifold. 29. Remove and discard the seal. 30. If replacing the upper intake manifold, turn and remove the PCV valve cover from the upper intake manifold. 31. Remove and discard the seal. 32. Remove the throttle body if replacing the upper intake manifold. 33. Remove the MAP sensor if replacing the upper intake manifold. Installation Procedure
Page 11 of 21 1. Install the throttle body, if removed. 2. Install the MAP sensor, if removed. 3. Install the PCV valve cover, if removed, using the following procedure: 3.1. Install a NEW seal (O-ring) on the PCV valve cover. 3.2. Lubricate the seal with clean engine oil. 3.3. Install the PCV valve cover in the upper intake manifold. 3.4. Turn and lock the PCV valve cover in position. 4. Install the power brake booster vacuum tube fitting, if removed, using the following procedure: 4.1. Install a NEW seal (O-ring) on the power brake booster vacuum tube fitting. 4.2. Lubricate the seal with clean engine oil. 4.3. Install the power brake booster vacuum tube fitting in the upper intake manifold. 4.4. Turn and lock the power brake booster vacuum tube fitting in position.
Page 12 of 21 5. Install a NEW seal on the fuel meter body assembly. 6. Lubricate the seal with clean engine oil. 7. Install a NEW upper intake manifold to lower intake manifold gasket in the groove of the upper intake manifold.
Page 13 of 21 8. Install the upper intake manifold onto the lower intake manifold. 9. If reusing the fasteners, apply threadlock GM P/N 12345382 or equivalent to the threads of the upper intake manifold attaching bolts. Notice: Refer to Fastener Notice in Service Precautions. 10. Install the upper intake manifold attaching studs. 10.1. Tighten the upper intake manifold attaching studs on the first pass to 5 Nm (44 inch lbs.). 10.2. Tighten the upper intake manifold attaching studs on the final pass to 9 Nm (80 inch lbs.). 11. Install the fuel lines to the fuel meter body assembly. 12. Install the EVAP canister purge solenoid valve.
Page 14 of 21 13. Install the bracket for the engine wiring harness on the lower intake manifold stud. 14. Install the engine wiring harness bracket nut. Tighten the engine wiring harness bracket nut to 12 Nm (106 inch lbs.). 15. Install the accelerator and cruise control cable bracket to the throttle body. 16. Install the accelerator and cruise control cable bracket nuts. Tighten the accelerator and cruise control cable bracket nuts to 9 Nm (80 inch lbs.).
Page 15 of 21 17. Install the accelerator control cable bracket to the throttle body and the intake manifold. Tighten the accelerator control cable bracket studs and nuts to 12 Nm (106 inch lbs.). 18. Connect the PCV valve hose assembly to the intake manifold and the valve rocker arm cover.
Page 16 of 21 19. Position the engine wiring harness. 20. Install the wire harness clip to the accelerator cable bracket. 21. Connect the following electrical connectors: The fuel meter body assembly (1) The Manifold Absolute Pressure (MAP) sensor(3) The EVAP canister purge solenoid valve (2) 22. Connect the following electrical connectors: The A/C compressor clutch (1) The A/C compressor cutoff switch (5), if equipped
Page 17 of 21 The Throttle Position (TP) sensor (2) The Idle Air Control (IAC) motor (3) 23. Connect the vacuum hose from the vacuum tank to the intake manifold. 24. Install the power brake booster vacuum hose to the intake manifold. 25. Install the cruise control cable, if equipped to the throttle shaft and the bracket. 26. Install the accelerator cable onto the throttle body.
Page 18 of 21
Page 19 of 21 27. Wrap the cable in between the finger of the hook tab and the pulley wall. Make sure that the cable is fully seated in the pulley groove. The cable must not lie outside of the hook tab. 28. Install the accelerator cable to the accelerator cable control bracket. Notice: Handle the MAF sensor carefully.
Page 20 of 21 Do not drop the MAF sensor in order to prevent damage to the MAF sensor. Do not damage the screen located on the air inlet end of the MAF. Do not touch the sensing elements. Do not allow solvents and lubricants to come in contact with the sensing elements. Use a small amount of a soap based solution in order to aid in the installation. 29. Install air cleaner outlet duct to throttle body. 30. Install air cleaner outlet duct to MAF sensor. Tighten the hose clamp to 4 Nm (32 inch lbs.). 31. Connect the IAT sensor harness connector.
Page 21 of 21 32. Install the air cleaner outlet duct retaining wingnut. Tighten the wingnut to 2 Nm (18 inch lbs.). 33. Connect the breather tube to the air cleaner outlet duct. 2010 ALLDATA LLC. All rights reserved. Terms of Use