1956 Mack LTL Diesel TYLDEN HERITAGE R MODEL MACK MAIL ORDER PARTS CATALOGUE Custom Classic Truck & Tractor Restorations Business Hours: 0428 507 408 Location: 1906 Trentham Road, Kyneton Vic 3444 Australia Note: Our workshop & warehouse are only open by appointment Postal Address: P.O. Box 614, Kyneton Vic 3444 Australia Supplier of after market Mack reproduction and dress up parts Big range of Mack B & R Model bits. Special Interest in: Mack Trucks...Diamond T Trucks...Caterpillar Tractors Trading since 1961 Email: tyldenheritage@bigpond.com web: www.tyldenheritage.com.au Lee No 3 Pty Ltd A.C.N. 005 204 599 A.B.N. 40 005 204 599 These pages may only be reproduced after obtaining written permission from Tylden Heritage. All rights reserved. COST PER PRINTED CATALOGUE INCL POSTAGE 10
INDEX FOR R MACK PARTS 1R. AXLE: Section 1 CHASSIS: ENGINE: Section 1. Bumper, Fuel Tank, Mudflaps, Steering, Tail Shaft. Section 1: Radiator, Starter Motor. 2R BONNET Section 2: Latches, JEWELLERY: Dogs, Emblems. 3R CABIN INTERIOR: Section 3. 4R CABIN EXTERIOR: Section 4. 5R DOOR PARTS: Section 5. SEE GENERAL SECTION CATALOGUE FOR OTHER PART OPTIONS - Parts for Axle, Brakes, Catches, Dress Up, Electrical, Parts Books, Rubber Parts, Reproduction Cast Parts, Steel Name Plates & Instruction Plates & Stickers.
SECTION 1---- R SERIES MACK PARTS E9 MOTOR - 2 AVAILABLE Mack E9-450 complete motor. Governed at 1800RPM. 4 Valve Serial No SK0280. Built new 1/3/85. Clutch CL795. - 2 available. 15,000.00 12 SPEED GEAR BOX - EX ABOVE Mack TRTXL 1070B 12 speed gear box. Serial No. 5K0892 5,000.00 REAR AXLE COMPLETE ASSEMBLY Rear axle air bag Mack SA38C Carrier CRDPC92 CRD93 Ratio 3.87 Spacing bogie 60 inches. 6,500.00 NOTE: ABOVE PARTS BUILT The above parts came from a Superliner 11 to give truck a required speed of 75 mph = 120Km per hour at 1800 rpm. SLEEPER BOX 60 inch sleeper box. Has been stripped out inside. Came from US built Superliner, has V type opening and comes with cabin cut out if required. 3,000.00 R CABINS - PAINT STRIPPED R Model cabin, hand stripped back to gal finish - no rust. Ready for painting inside and out. 6,500.00 R CABIN COMPLETE - WHITE R Model cabin complete as lifted out of classic. Very good condition and would not require painting if used for work truck. 8,500.00 NEW MACK BUMPERS Suit new Superliner, Titan bumper, complete mounting kit with front under protection. (FUP). 1,000.00 R MODEL FIBREGLASS BONNET R Model fibreglass bonnet. Does not include grille. 750.00 EARLY 'R' DOOR - LIKE NEW Early door, complete with early type door lock & window winder. Ex USA fire trucks. 1,500.00 R MODEL-1 AXLE
SECTION 1---- R SERIES MACK PARTS CHASSIS PARTS R MODEL DIFF Single axle diff hub to hub ex R model - ratio 4.25 with springs. 2,000.00 AXLE HUB - MODERN CONVERSION Axle wheel hubs for conversion to 10 stud USA from Spider. Suit 44000lbs diff. Made in USA. NEW. Price Per Each. Mack Part No MK3398HR735K 635.00 Brake drum for 2947. NEW. Price Per Each. 120.00 BUMPER BAR R Model standard bumper bar - black. New. Made in USA POA R Model standard bumper bar - chrome. New. Weight 25kg. Length 2450mm, height 450mm. Flanges are 90mm. 1,950.00 BUMPS STOP SPRING Front spring buffer, suit R, flat top 2 1/4 high, 2 1/8 diam, 3/4 long X 3/8 locating bolt...see Rubber Parts General Section 6G-6 for pricing and options BATTERY BOX. Heavy duty Mack battery box base with ribbed top - 2 sections. New. Note: we can supply lid chrome plated. 380.00 Heavy duty Mack type battery box, bottom section holds 2 batteries with rubber latch/catch- as on R model - new. Note: we can supply chrome catch for B Model. 263.90 R MODEL-1 AXLE
SECTION 1---- R SERIES MACK PARTS CHASSIS PARTS BATTERY BOX. (cont) Black steel ribbed top battery box lid cover - correct for R model - NEW. Note: we can supply lid chrome plated. 145.60 Steel battery hold down bracket, hold the batteries securely - not stocked. 81.90 Nickel Cadium carriage bolt. Holds batteries bracket down - 2 required (sold as a kit)- not stocked 10.00 ELEPHANT SPRING INSULATOR FEET Top insulator, suit 44000. 4 Required. Price Per Each. SEE RUBBER PARTS IN GENERAL SECTION 6G-19 FOR PRICING. Top insulator suit 34-38000 steel base, 6ins x 4 1/2 ins 1 3/4 dowl. 4 Required. Price Per Each. SEE RUBBER PARTS IN GENERAL SECTION 6G-19 FOR PRICING Lower insulator. Suit 34-38 & 44000 rear end. Steel Base 6 1/8 x 6 1/8 1 3/4 dowl. 4 Required. Price Per Each.SEE RUBBER PARTS IN GENERAL SECTION 6G-19 FOR PRICING. Side spacer of lower insulator Neoprene. 8 Required. Price Per Each. SEE RUBBER PARTS IN GENERAL SECTION 6G-19 FOR PRICING. MUD FLAPS Mack facing dog. SEE RUBBER PARTS IN GENERAL SECTION 6G-18 FOR PRICING AND OPTIONS. FUEL TANK J BRACKET ROLLED EDGE STRAP Rubber Fuel Tank Strap - 2 inch. Comes in bag of 25ft. (7.6M) SEE RUBBER PARTS IN GENERAL SECTION 6G- 20 FOR PRICING AND OTHER OPTIONS. R MODEL-1 AXLE
SECTION 1---- R SERIES MACK PARTS R MODEL FUEL TANK FLAT STRAP R Mack flat fuel tank strap. 2 1/8 wide 1/8 thick (has no edge turn up). Sold Per Foot. SEE GENERAL SECTION 6G- 20 FOR PRICING & OPTIONS FRONT FUEL TANK SUPPORT RUBBERS R fuel tanks per each. 3 3/4 in long x 2 5/8 diam x 1 1/2 hole are split for fitting. SEE GENERAL SECION 6G-20 FOR PRICING & OPTIONS. STEERING PARTS BEARING R Bearing Steering Shaft. Size shaft 1 inch OD 2 inch. 75.00 R Bearing Steering Shaft Firewall. Size shaft 1 inch hole, centres 3 1/2 inch. 82.00 DUST COVER R Rubber dust boot steering shaft 1 inch (25mm) round hole. See Rubber Parts in General Section 6G-5 for pricing and options. 14.50 R Rubber dust boot slip yoke 4 slots to suit shaft. See General Section 6G-5 for pricing & options. SHAFT Shaft steering lower - suit Superliner 2 and other models 250.00 Shaft steering main - suit Superliner 2 over all length 46 inches (1070mm) as in photo thats with 6 inch (150mm) inside yoke 510.00 R STEERING YOKE Yoke. Steering Shaft Ross Box. (.875 inch ID). Bin 3091 65.00 R MODEL-1 AXLE
SECTION 1---- R SERIES MACK PARTS ENGINE Air starter motor used. Note: Pinion lengths vary. 400.00 Air starter valve remote valve assembly. NEW 279.00 12V air starter solonoid control valve - to suit 3179. NEW 206.00 AIR INTAKE FITTINGS Air Hose hump connector, straight, suit 5 inch tube. Suit Superliner. SEE GENERAL RUBBER SECTION 6G-16 FOR COST & OPTIONS Air hose connector, straight, suit 6 inch tube. SEE GENERAL RUBBER SECTION 6G-16 FOR COST & OPTIONS Air elbow 38 deg. Suit 5 inch tube. SEE GENERAL RUBBERS SECTION 6G-16 FOR COST & OPTIONS Air elbow 38deg. Suit 6inch tube. Suit Superliner. SEE GENERAL RUBBER SECTION 6G-16 FOR COST & OPTIONS Air elbow 90 deg suit 5 inch tube. SEE GENERAL RUBBER SECTION 6G-16 FOR COST & OPTIONS Air elbow 90 deg suit 6 inch tube. SEE GENERAL RUBBER SECTION 6G-16 FOR COST & OPTIONS INTERCOOLER CLAMP Spring loaded inter cooler clamps - 5 inch. SEE GENERAL SECTION 6C-2 FOR COST & OPTIONS Spring loaded inter coller clamp - 6 inch. SEE GENERAL SECTION 6C-2 FOR COST & OPTIONS R MODEL-1 AXLE
SECTION 1---- R SERIES MACK PARTS ENGINE PARTS - 6 CYLINDER WATER PUMP KIT Suit most 60's & 70's Macks 5/8 shaft. (Note: shaft lengths do vary with number of pulleys and front bearing sizes may vary also) 130.00 WATER PUMP PARTS E9 V8 Water Pump Kit - 9 Pieces. NOTE: This kit bushes need reaming after fitting. 550.00 Water pump, complete new unit 1,300.00 Water pump seal only, suit above kit suit 3/4 shaft 1 5/8 OD. Suit E9. Bin 3106 60.00 LUBERFINER Engine oil filter Luberfiner. Length15 inches (380mm) diameter 7 1/2 inches (190mm). Suit 675 and other similar build engines 120.00 E9 EXHAUST Gasket Exhaust E9. 3.5/8 bolt. Centres 21/2 x 2 1/2 hole..per EACH 37.00 Oil Ring Turbo Oil Drain 3.00 Gasket Ring Exhaust - PER EACH 50.00 Oil Drain Gasket 1 inch hole. 2 1/16 bolt holes 8.45 Turbo gasket. 33.00 Oil Drain Gasket. 1/2 inch hole. 1 1/2 inch bolt holes. 5.00 R MODEL-1 AXLE
SECTION 1---- R SERIES MACK PARTS E 9 PARTS (CONT) DRAG LINK COVERS Drag link leather grease covers with lace - new. See Rubber Parts in General Section 6G-13 for pricing. POWER STEERING Original power assist booster type steering kit - Used (note: pump not included) as taken off used trucks. See engine parts in next section for pump options. 2,750.00 POWER STEERING PUMP Generator with regulator and power steering drive type and oil pump as fitted to B & early R Models with power assist optional steering from new 445.00 DRIVE COUPLING Rubber Drive coupling for power steering pump of Generator. B & early R models. (as above)..bin 131 100.00 POWER STEERING PUMP V8 Power Steering pump with drive - suit 864 V8 - Used 500.00 SECTION 1---- R SERIES MACK PARTS ENGINE BELT DRIVE Power Steering pump -Belt drive 250.00 Power Steering Pump Bracket 100.00 R MODEL-1 AXLE
R MODEL ENGINE MOUNTING INSULATORS Mack engine mounting rubber. Fits some Flintstones, R Model, V/Liner, Superliner, Ultraliner, Cruiseliner etc from about 70's to around 1990's where they run 8 rear engine mounts, also used as front engine mount on some models. Note: Very common engine mounts. Size of 2745 & 2747 80mmx20mmdeep with 50mm wide and 18mm hgh centre. Number depending on model. 8 required for most models. 8 standard mounts. Price per each. Top harder rubber yellow dot used on rear top mount. 4 per truck. Price per each 22.50 30.45 ENGINE PLATES Mack engine exhaust emission control information rocker cover plate. 200mm long x 70mm high. Supplied blank for your detail. See General Section 6I-2 for price & options. MACK GENERAL MODELS ( Photocopy) Workshop Manual - 937 Pages - Early - Covers Models B67-138.00 673-70. Includes Mack C.M.B.F.R.U & Flintstone - For Engines END 465 - END 673 - ENDT 673 - ENDT673 & B - END 711 - END 864 - ENDT 864. Fuel pump, clutch, gear box, drive shaft, diffs, came with our first new R Model Mack in 1976 MACK R WORKSHOP MANUAL (Photocopy) Workshop Manual - covers R-RD-U & DM models - 338 Pages. Chassis, cooling, front axle, steering, springs, & suspension, wheels, brakes, electrical. Cabs. This book came with our first new R model Mack in 1976 91.00 R MODEL-1 AXLE
R MODEL - SECTION 2 BONNETT, JEWELLERY, LATCHES BONNET LATCH SHORT TYPE - STEEL BONNET 3290 R Model black hood latch with square body - New - 4 required per truck - Note: bottom pin needs turning for some models - sold per each - catch is extra. Square tube section 3 1/2 inch x 90mm long 81.90 3291 R Model black hood catch for above NEW Price Per Each. 25.00 OPTIONAL CHROME- SHORT TYPE 3292 Model R chrome hood latch with square body - new. Sold per each. Note: Catch is extra. Square tube section 3 1/2 inch x 90mm long 200.00 3293 Model R chrome hood latch for above - new. Suit 3292. Bin 3297 40.00 MODEL R HOOD LATCH 3294 Model R hood latch socket - NEW not painted. Bin 3293 24.50 USED BLACK SHORT TYPE 3295 Used R Model black short square - some rust. Used. 40.00 BONNET LATCH - LONG TYPE - FIBREGLASS BONNET 3296 Latch - R model chrome fibreglass hood (bonnet) 8 inch (200mm) pin centres with adjustable length. Suit Superliner 11 & Valveliner. Sold Per Each. 3297 Latch - R Model black fibreglass hood (bonnet) 8inch (200mm) pin centres. 2 Per Truck. Sold per Each. Square tube section 5 1/2 inch x 140mm long. 92.00 70.00 BONNET LATCH SPRING - SHORT TYPE 161 Replacement spring bonnet latch. 80mm long x 13mm wide - Bin 141 22.75 BONNET LATCH RUBBER 3302 Long bonnet latch. Suit Superliner 2 and others. Length centre of mounting pin to latch connecting point - 7 inch x 180mm overall length 330mm x 13 inch. 89.00 R MODEL-2 BONNET ETC
R MODEL - SECTION 2 BONNETT, JEWELLERY, LATCHES SOCKET CLIP FOR 3302 3305 Clip for long rubber bonnet latch. Part No 3302. As fitted to Superliner and Valveliner. PRICE PER EACH. 38.50 3301 Short bonnet latch. Also suit battery box and some bonnets. PER EACH. Length centre of mounting pin to latch connecting point 4 3/4 inch x 125mm. 25.50 SOCKET CLIP FOR 3302 3299 Clip for short bonnet hatch. Bin 3301 10.20 3260 Lower mounting kit for 3301 11.00 BONNET WEAR STRAP 3300 Nylon cabin to hood wear strap. R Model. PER EACH 31.00 BONNET HINGE 3268 Bonnet hinge ball type 98.00 3269 Bonnet hinge pivot ball type. Suits R Model bonnet mount (with front radiator mtg intercooler). 120.00 R BONNET LOCATING ROLLERS 3298 Bonnet locating rollers. 3 inch diam 2 3/8 wide, 5/8 hole 105.00 BONNET FLARES 3273 R Model bonnet mudguard flares 599.00 BONNET BADGES GRILLE FRONT LETTER SET - R MODEL 3310 Mack letter set. Front. Suit R Bonnet (hood). NEW. Letter size- 5 1/2inch by 3 1/4 inch 107.00 R MODEL-2 BONNET ETC
R MODEL - SECTION 2 BONNETT, JEWELLERY, LATCHES, DOGS etc CABIN FRONT LETTER SET - F MODEL 3312 Mack F letter set. Front of cabin. New. Letter size 2 inch high 98.00 SIDE SCRIPT 3311 Mack script name - side 9inch x 3 inch. NEW. Sold Per Each. 48.00 BONNET BADGES 3318 Econodyne Emblem - suit R Model - Price Per Each. Not stocked 115.00 3319 Maxidyne Emblem - suit R Model - not stocked POA 3321 Super liner emblem. Price per Each. NEW. 140.00 HALF DOG 3322 Mack R - Half Dog - 2 per truck. L&R hand...new. Price Per Each 63.70 LATE MACK HALF DOG 3270 New Mack logo standing half dog. Left and Right, facing each other. Cast from brass, detailed and chrome plated. PRICE PER SET OF 2 DOGS. 170.00 MACK LETTER SET 3271 New Mack logo letters. Set of 4, cast from brass, detailed and chrome plated. Price per Set of 8 letters. Bin 3270 280.00 EARLY MACK DOG 654A New old stock Mack long ear dogs, as fitted to Mack trucks 1932 to 1979. 225.00 LATE MACK DOG 3307 Late Mack Short Eared Dog. Standard bonnet size...new 159.00 DOG BASE 3308 R Model base for Bulldog - chromed with special screws.new 50.00 R MODEL-2 BONNET ETC
R MODEL - SECTION 2 BONNETT, JEWELLERY, LATCHES, DOGS etc REPRODUCTION MODEL BADGES 3324 Mack R600 badge.cast from Brass, Detailed & Chromed - length 210mm (8 1/4 inch) 165.00 3325 Mack R700 Badge, Cast from Brass, Detailed & Chromed. Length 210mm (8 1/4 inch) 165.00 3326 Mack F700 Badge. Cast from Brass, Detailed & Chromed. Length 210mm (8 1/4 inch) 165.00 3327 Mack R800 badge. Cast from brass. Detailed & Chromed. Length 210mm (8 1/4 inch) 175.00 3330 V8 Side Badge. Cast from Brass. Detailed & Chromed. 90mmx60x8 thick. 165.00 BONNET BADGES GRILLE 3303 Grille - Suit R & F - New or Used and Reconditioned. Price subject to quality & stock. Priced on condition. 1,000.00 FIBREGLASS GRILLE MOUNTING 3304 New fibreglass mounting surround POA GRILLE MOULDING 3306 Grille surround moulding - black, in 2 sections. POA 3313 New Headlamp Assembly 12V. Fits most Macks with single round headlight also other model trucks & cars. Supplied with lens body and lead ready for fitting. 85.00 3314 Headlamp Gasket for 3313 light assembly. 11.00 3317 Chrome head light bezel. Suits steel style fronts, R also DM, Valueliner and Flintstone & B80 & 81 Tylden JR ute. Size rear ID 210mm front ID. 185mmx30mm deep. Sold Per each. 103.00 R MODEL-2 BONNET ETC
R MODEL - SECTION 2 BONNETT, JEWELLERY, LATCHES, DOGS etc 3316 Headlight Trim. New Stainless steel 16 5/8 long x 9 1/4 high. 7 3/8 inch hole. Price Per Each. NOTE: This type has only 2 bolt holes and is a wee bit smaller than the 6 bolt hole one. 99.00 HEADLIGHT BEZEL 3332 Duel headlight bezel. Suit Superliner. 1 3/4 (45mm) deep with mounting screws. PRICE PER EACH 97.00 3333 Dual headlight bezel. Suit Superliner. 1 3/8 (35mm) with mounting screws PRICE PER EACH 130.00 HEADLIGHT ASSEMBLY 3338 Complete oblong head light assembly RH (see part no 3332 for chrome bezel) 229.00 3339 Complete oblong head light assembly LH. (see part no 3332 for chrome bezel) 229.00 ROUND BLINKER (INDICATOR) LIGHTS 772 Fender (mudguard) turn signal LED round face look a like 100mm light with chrome bezel - amber both sides - suits B & R model & other US built trucks - SOLD PER EACH SEE GENERAL 6E-1 FOR PRICING & OTHER OPTIONS R TYPE SQUARE BLINKER 3334 R Model double side square LED hood top mounting blinker lamp includes wiring tail. NOTE: This light has built in side lamp so 3335 below would not be necessary. SEE GENERAL 6E-1 FOR PRICING & OTHER OPTIONS SUPERLINER STYLED DUAL FACE BLINKER 3341 Combination turn signal, side marker & park light signal with round lens. USA made, grey body with amber or amber and red main lens. Replaceable globe 12V 2.1A 0.5 minor. 4 wires. Price Per Each. SEE GENERAL 6E FOR PRICING & OTHER OPTIONS ROUND BLINKER SIDE AMBER 3335 R Model side hood blinker lamp assembly. - Amber with wiring. SEE GENERAL 6E-1 FOR PRICING & OTHER OPTIONS. PARK LIGHTS 3336 Lamp Marker Park Light Assembly, clear with wiring. See General Section 6E-7 for Pricing. 3337 Parking light lens only - clear or amber for above. 3335 & 3336. See General Section 6E-7 for Pricing and options. R MODEL-2 BONNET ETC
R MODEL - SECTION 2 BONNETT, JEWELLERY, LATCHES, DOGS etc FRONT MUDFLAP 3340.Mudflap bonnet LH & RH R Model black with brass eyelets, not Valveliner. See Rubber Parts in General Section 6G-18 for pricing and options. BONNET (HOOD) WEBBING 2692 Suit Flintstone etc. - See Rubber in General Section 6G-4 for Pricing and Options. BONNET MOUNTING RUBBERS 2746 Bonnet pivot mounting insulators. Supplied with 2 large lower & 2 small upper. Note: this part fits some R, V/Liner, S/Liner & early Titans and cab and sleeper box mounts as well. Size 65x30 with 52x13 top. See Section 6G-3 for pricing. 2748 Lower bonnet mount size 52mmx13. See Rubber in General Section 6G-3 for pricing and options. R MODEL-2 BONNET ETC
R MODEL - SECTION 3 - CABIN INTERIOR WESTERN TRIM 3345 Tylden offer a full R Model Western Trim package as per factory with large facing dogs or diamonds hot welded into material or optional stitched with buttons. Available in brown, cream, grey, magnum (red), or colour of your choice. Western Trim including 2 seats (part No 3347), 2 Door trims (Part No 3348), Rear Cab (Part No 3349) and Hood Lining (Part No 3350). 2 Pillar Trims. NOTE: ALL PRICES SHOWN ARE FOR UPHOLSTERY ONLY. 3347 Bucket Seats, original perforated vinyl with Mack Logo stamp (as original) Price Per Each. Ask us to email better photos. 2,560.00 400.00 3348 R Model Western door trim with welded dog logo. Original welded patterns or stitched with buttons. Price Per Each. Ask us to email better photos. 400.00 3356 R Model door arm rest, included with 3348 OR Price Per Each. Ask us to email better photos. 25.00 3349 R Model rear Western original pattern cab lining in perforated vinyl. Ask us to email better quality photos. 3350 R Model roof head lining in perforated vinyl. Ask us to email better quality photos 475.00 475.00 FOLLOWING NOT INCLUDED IN PART NO. 3345 PACKAGE ABOVE PRICES ROOF CONSOLE 3351 R Model front roof console 160.00 FLOOR CONSOLE 3352 R Model centre floor console in vinyl and carpet, base & lid. - trim only. Supplied by Customer. NOTE: Photos shows a special one. 170.00 ALL NEW FLOOR CONSOLE 3357 Complete new centre console, 390mm long x 300mm deep x 280mm wide, folded from S/S with hinged marine ply. Lid covered in vinyl with carpet kick strip on bottom with stamped dog logo in lid. Photo show lid only. 3356 Stainless steel centre console base, 390mm x300mm deep x 280 wide. 290.00 148.00 R MODEL-3 CABIN INTERIOR
R MODEL - SECTION 3 - CABIN INTERIOR CABIN SIDE INFILL 3358 Cabin side kick infill same colour of interior. 98.00 HATCH SURROUND 3353 R Model hatch surround 55.00 DOOR PILLAR 3354 R Model Side front pillar trims - L & R at top of photo. Centre of photo shows door arm rests - part 3356. Bottom photo are angles to hold roof console part 3351. Note: 3356 & 3351 are display only. DOG STAMP 3365 Stamp your material with original dog type stamp PRICE PER EACH. 110.00 45.00 INTERIOR LIGHT 3364 R Model dome interior light with switch and lead. 99.00 DASH 3412 Dash - new. Made from fibreglass POA DASH PANEL LH 3410 New R model genuine dash - left hand section. Including top hatch. 1,385.00 GLOVE BOX LID 3413 New glove box lid to suit above 135.00 DASH PANEL RH 3411 New R model genuine dash - right hand section. 539.00 3516 Dash Panel Screw. See door for nut. Bin 3540 3.00 3519 Nut dash and door trim. Bin 3540. 3.00 R MODEL-3 CABIN INTERIOR
R MODEL - SECTION 3 - CABIN INTERIOR ENGINE STOP CABLE 3359 R Model engine stop cable. Red Knob. 80.00 HAND TROTTLE CABLE 3360 R Model hand throttle cable. Black knob. 80.00 STANDARD MATCHING GAUGES SUIT R & B MACK SPEEDO 3367 Speedo gauge. 0-120 kmh cable 3 1/4 diam. 200.00 3368 R Model speedo cable with 2 types of adaptors -112 Length 3050mm 70.00 TACHO 3369 Tacho gauge. Zero to 3200 RPM with built in hour meter. 3 1/4 inch. 210.00 3370 R Model Tacho cable with 3 types of adaptors. 2250mm long. 70.00 MECHANICAL OIL PRESSURE GAUGE 3372 Oil pressure gauge. 0-50 PSI mechanical. Suit 2 inch hole mounting. 128.00 LOW OIL PRESSURE SWITCH 3373 Low oil pressure warning engine switch 51.00 OIL TEMPERATURE GAUGE 3378 Mack Gauge - Oil Temp. Engine, Transmission & Diff. 60 to 160 Cel.Bin 3373. 125.00 3379 Mack Gauge - Oil Temperature Sender for 3378. Transmission & Diff. 60.00 R MODEL-3 CABIN INTERIOR
R MODEL - SECTION 3 - CABIN INTERIOR VOLT METER 3377 Mack Gauge Volt 12V 10 to 16amps battery condition and charge section 110.00 WATER TEMPERATURE GAUGE 3380 Mack Gauge - Water Temp Neg 100-230 Fahrenheit 105.00 3381 Mack Gauge - Water Temperture Sender Unit. Negative Ground. Bin 3373 55.00 AIR PRESSURE GAUGE 3386 Mack Gauge - Air Pressure Dual needle 50mm diam. 1000KPA 1/8-27 NPTF. 140.00 FUEL GAUGE 3387 Fuel Gauge 105.00 3388 Sender Fuel Gauge R & F multi volt. Suit tank 6-24 inch deep. Suit Pal & Mack gauges. 250ohm empty 1020ohm half full & 31ohm full. 81.00 TACKO WITH MACK LOGO 1030 Tachometer head - black face with Mack logo. 0 to 3200 RPM with engine hours. Cable operated. Suit 85mm diam hole. 178.00 GAUGE INDENTIFICATION STICKER 1281 Gauge face sticker for 1 and 2 diff, engine and oil temp. See stickers in general section 6J-5 for pricing and options. INDICATOR STALK - TURN SIGNAL 771 R Series indicator stalk - 7 wires. See General Section 6E-1 for pricing and options. 3383-8 R Series indicator stalk. - 8 Wires. See General Section 6E-1 for pricing and options. R MODEL-3 CABIN INTERIOR
R MODEL - SECTION 3 - CABIN INTERIOR DIP SWITCH 3389 R Series dip switch with long or short leg. Bin 3377 55.00 LOCK SET IGNITION & DOOR 856 Lock Kit Ignition and door lock R & F. See General Section 6E- 2 for pricingbin 88 CUSTOM HORN BUTTON LOGO 1258 Custom horn button logo with your Custom details. Mounted on S/S plate for easy mounting on your horn button. See Stickers in General Section for Pricing. 38.00 FRONT FLOOR MAT 3391 R Model front floor mat - moulded rubber ribbed with Mack logo & wear section on LH side. 429.00 REAR FLOOR MAT 3392 R Model rear floor under seat mat - moulded ribbed rubber 200.00 3393 R Model plain floor mat (no ribs etc) supplied in one section. LOOSE FLOOR MAT 2771 Floor mat - loose with dog logo with cut out for peddles. Sold as Pair. The second (passenger side) one is square. 135.00 R MODEL CLUTCH PEDAL 3406 R Model clutch pedal & bracket clutch type. Generally stocked to change from old through floor pedal type to pendulum type with cable. Photo shows insulation in B Model. - Used 230.00 CLUTCH CABLE 3404 Suit R600 & Valveliner 109" (2770mm) 112" (2850mm) tip to tip. 144.00 3403 Suit Trident, Titan, VL S/L, 138" (3480mm) long 220.00 R MODEL-3 CABIN INTERIOR
R MODEL - SECTION 3 - CABIN INTERIOR GEAR SHIFT BOOT 2869 Gear shift boot - rubber - 180mm long x 100mm wide x 70mm high. See General Section 6G-5 for pricing 2868 Stainless steel surround Cover for boot 2869. See General Section Rubber 6G-5 for Pricing. 2870 Steering Column gear shift boot and rubber - 222mm long x 135mm wide x 70 high.see General Section 6G-5 for pricing CLUTCH RUBBER 2482 Clutch pedal - rubber replacement pad, also fits B Model. See General Section 6G-1 for pricing. R MODEL FOOT VALVE PEDAL 3074 New brake pedal with Mack logo. Note holes are not drilled. See General Section for other brake options. 78.00 THROTTLE PEDAL 361 R Model fuel pedal only with Mack logo - New. Price Per Each. 72.80 KICK PLATES 3415 R Door entry aluminium kick plates. Price Per Each. 45.00 3414 R Model Entry Kick Plate. Custom Polished Stainless Steel. POA HEATER DUCT 3407 Round heater duct vents - suit R Model POA 3408 Oblong heater duct vents - suit R Model POA R MODEL-3 CABIN INTERIOR
R MODEL - SECTION 3 - CABIN INTERIOR VINYL STICKERS - GENERAL STEERING WHEEL 3454 Mack optional upgrade. 18 inch 4 spoke steering wheel. See General Section 6D for pricing. POA 3455 Steering wheel hub for above to suit R model standard steering shaft. POA MACK AIR ACTUATORY 3405 Mack red dot part no 4379-RD554144 suit Mack CHR 1992 to about 2000. Used to open and close air vent shutters. 60.00 DRIVER INSTRUCTION STICKERS SEE GENERAL SECTION - 6J FOR OPTIONS R SERIES MACK CAB STICKERS 1236 WARNING TOWING. See Stickers General Section 6J-5 for pricing 1237 COMPOUND TRANSFER CASE See Stickers General Section 6-5J for pricing 1241 MAXIDYNE OPERATING INSTRUCTIONS. See Stickers General Section 6J-5 for pricing ` 1244 CAUTION T2090 TRANSMISSION. See Stickers General Section 6J-5 for pricing 1246 STEERING LOCK ADJUST STICKER 60x30mm - SAMPLE PHOTO See Stickers General Section 6J-5 for pricing 1274 DOOR ENTRY WARNING sticker 100x60mm. See General Section 6J-5 for pricing 1280 HORN COVER LOGO. Rectangular horn cover 112mm long 56mm deep. Wording is 107mm long. See General Section 6J-5 for pricing GAUGE INDENTIFICATION STICKER 1281 Gauge face sticker for diff 1 & 2 gearbox and engine. See General Section 6J-5 for pricing. R MODEL-3 CABIN INTERIOR
SECTION 4 - R MODEL CABIN EXTERIOR AIR CLEANER 3460 Used RH Mack air cleaner (sample photo) POA AIR CLEANER TOP HAT NUTS 3190 Nut top of air cleaner. 24 in set. Price per each nut. 5.00 AIR CLEANER HAT 3461 Air cleaner hat - black plastic 15in x 3 1/2 plus sprigit extra 1 1/2 ins rain. 140.00 AIR CLEANER SERVICE INSTRUCTIONS 1276 Air Cleaner Service Instructuion for EBA15 as fitted to Superliner and other models. 180mmx145 20.00 AIR CLEANER ELEMENT INFORMATION 1278 Air Cleaner Element Information Sticker. Length 120mmx70mm 15.00 AIR INTAKE FITTINGS 2739 Air Hose hump connector, straight, suit 5 inch tube. Suit Superliner. SEE GENERAL RUBBER SECTION 6G-1 FOR COST & OPTIONS 2742 Air hose connector, straight, suit 6 inch tube. SEE GENERAL RUBBER SECTION 6G-16 FOR COST & OPTIONS 2740 Air elbow 38 deg. Suit 5 inch tube. SEE GENERAL RUBBERS SECTION 6G-16 FOR COST & OPTIONS 2743 Air elbow 38deg. Suit 6inch tube. Suit Superliner. SEE GENERAL RUBBER SECTION 6G-16 FOR COST & OPTIONS 2741 Air elbow 90 deg suit 5 inch tube. SEE GENERAL RUBBER SECTION 6G-16 FOR COST & OPTIONS 2744 Air elbow 90 deg suit 6 inch tube. SEE GENERAL RUBBER SECTION 6G-16 FOR COST & OPTIONS Page 22 R MODEL-4 CABIN EXTERIOR
SECTION 4 - R MODEL CABIN EXTERIOR AIR HORN - ROUND 3439 Horn - Air - round trumpet kit. 141.00 AIR HORN - RECTANGULAR 3440 Mack horn air rectangular - front with snow cover with mounting kit. 210.00 HORN COVER LOGO 1280 Rectangular Horn Cover 115mm long 56mm deep. Wording is 110mm long. 18.00 CABIN INSULATOR 3434 Cab insulator R cabin. Also R fuel tanks per each. 3 3/4 in long x 2 5/8 diam x 1 1/2 hole are split for fitting. 28.00 CAB ENTRY GRAB HANDLE 3437 Grab entry handles. 23 long. Price Per Each. 78.00 CAB LEVELLING VALVE 3467 Valve cab levelling suit R Model + T401 Kw. 148.00 CABIN SUPER CUSHION AIR BAG 3468 Cabin rear air spring bag. Max inflation 100 PSI. Max Torque 15ft lbs. Length 5 1/4 inch. Diameter at big end - 3 1/2 inch 86.42 CABIN BULLET LIGHTS 3444 Bullet type roof lights 390mm long x 90mm diam, supplied with mounting bolts. See General Electrical Section 6E for pricing and options. 3445 Bullet short centre light. 200mm long x 90mm diam. Price Per Each. See General Electrical Section 6E for pricing and options. ROUND BLINKER (INDICATOR) LIGHTS 772 Fender (mudguard) turn signal LED round face look a like 100mm light with chrome bezel - amber both sides - suits B & R model & other US built trucks - SOLD PER EACH SEE GENERAL 6E FOR PRICING & OTHER OPTIONS Page 23 R MODEL-4 CABIN EXTERIOR
SECTION 4 - R MODEL CABIN EXTERIOR R TYPE SQUARE BLINKER 3334 R Model double side square LED hood top mounting blinker lamp includes wiring tail.. (see Electrical in General Section 6E-1 for pricing). NOTE: This light has built in side lamp so 3335 above would not be necessary. SEE GENERAL 6E FOR PRICING & OTHER OPTIONS SUPERLINER STYLED BLINKER 3341 Combination turn signal, side marker & park light signal. USA made, grey body with amber or amber and red main lens. 4 wires. Price Per Each. Extra 2 Amber lens. SEE GENERAL 6E-1 FOR PRICING & OTHER OPTIONS ROUND BLINKER SIDE AMBER 3335 R Model side hood blinker lamp assembly. - Amber with wiring. SEE GENERAL 6E-1 FOR PRICING & OTHER OPTIONS. CABIN VENTS TOP ROOF VENT 3449 Cabin top roof vent cowl assembly 240.00 R MODEL CABIN ROOF VENT SEAL 3420 Roof Vent Seal. 37 INCHES (940mm) 38.00 SIDE CABIN VENT 3450 Side Vent Cover. 160.00 SIDE CABIN AIR VENT RUBBER 2621 R Model side air vent sealing rubber. 10mmx8mm. 700mm (27 1/2 inches) per vent. SEE SECTION 6G-15 FOR PRICING FRONT VENT OPENER OPTION 901 Optional front vent opener. Can be adapted to suit without a lot of modification. 155mm closed 205mm open. Max load 125kg. Travel speed 6mm per second. Has inbuilt limit switches supplied with 12V switch. 125.00 MIRROR - SEE DOORS NEXT SECTION Page 24 R MODEL-4 CABIN EXTERIOR
SECTION 4 - R MODEL CABIN EXTERIOR WINDSCREEN GLASS 3416 Windscreen glass LHR, suit R. valve, super, metro. Weight 6Kg. 31 inches (800mm) x 21 inches (530mm). 160.00 3417 Windscreen glass RHR, suit R, valve, super, metro. 160.00 R MODEL WINDSCREEN RUBBER 3418 Windscreen rubber - complete both sides. 215.00 REAR WINDOW 3430 R Model rear window - laminated. Tinted Std. Auto glass. 150.00 3432 Rear window rubber seal. 98.00 MIRROR SEE DOOR PARTS - NEXT SECTION R MODEL WIPER BLADE 3497 Windscreen wiper blade. R Model. 16 inch long. 39.00 F MODEL WIPER BLADE 3498 Windscreen wiper blade - F Model - 20 inch long (500mm) 58.00 R MODEL WIPER ARMS 3495 LH wiper arm with inbuilt concealed windshield washer nozzles & two knurled drive options. 107.00 3496 RH Wiper arm with inbuilt concealed windshield washer nozzle and two knurled drive options. 107.00 WINDSCREEN BOTTLE 3499 Reservoir windscreen washer bottle cap & pump. R model door. 125.00 3493 Washer bottle cap only 16.00 Page 25 R MODEL-4 CABIN EXTERIOR
SECTION 4 - R MODEL CABIN EXTERIOR WINDSCREEN BOTTLE PUMP 3494 Washer bottle pump 46.00 STEEL PLATE FIREWALL PLATE 1235 Blank Firewall certification plate (See General Section 6-3I for pricing). Page 26 R MODEL-4 CABIN EXTERIOR
SECTION 5 - R MODEL - DOORS 3500 Door shell - R Model - new Left - suits 79 onwards door locks. 990.00 3501 Door shell - R Model. New right. Sit 79 onwards door locks. 990.00 3503 Door - R Model - Used. Ask re condition & price. Shell or complete. DOOR INNER PANEL 3506 Door inner panel RH late bare - NEW 210.00 3516 Door panel screws. Price Per Each. Bin 2904 3.00 2590 Door Panel J Nuts - 1/4 in thread. Bin 2907 3.00 DOOR HANDLE 3523 R door handle. Outer R & F model cb. 79.50 3524 R door handle inner R & F pre 79 NOTE: Part no. 3522 below has better clearance. 79.50 3522 R Model door handle late - inner R & F after 1979 with thicker Western trim. NOTE: Later type, fits pre 79 door if you need better clearance. 70.00 3521 R Model door pull handle. Suit R, RB, RD, DM, MC, MR & LE. R MODEL-5 DOORS
SECTION 5 - R MODEL - DOORS PLEASE NOTE: DOOR PART CHANGES IN 1979 AND 1983, DOOR HANDLE ESCUTCHEON 3526 Handle escutcheon. Suit door and window crank handle. 9.90 3527 Pin Handle window & door. Suit door and window crank handle. Bin 3526. 2.15 QUARTER VENT WINDOW 3528 Vent window flipper LH. (Quarter Vent), Suit models R & F. 275.00 3529 Vent window flipper RH. (Quarter Vent). Suit models R & F 275.00 GENUINE MACK SUPPLY 3532 R model vent window flipper (quarter vent). LH only. Bin 3533 356.00 3533 R model vent window flipper (quarter vent). RH only. 356.00 3571 R Model vent window flipper (quarter vent) outer rubber seal LH only 104.00 3572 R Model vent window flipper (quarter vent) outer rubber seal RH only 104.00 R MODEL DOOR GLASS 3530 Door glass R & L. Note: We supply 6mm green tinted toughened auto glass. 102.00 R MODEL EARLY WINDOW REGULATOR 89 Window regulator scissors - Left. Suit early R style cabs. 159.00 90 Window regulator scissors - Right. Suit early R style cabs. 159.00 R MODEL EARLY REGULATOR GEAR PLATE 91 Gear plate for passenger side door regulator. Suit early style cabs. 149.00 92 Gear plate for driver side door regulator. Suit early styled cabs. 149.00 R MODEL-5 DOORS
SECTION 5 - R MODEL - DOORS EARLY SIDE GLASS SUPPORT CHANNEL PLEASE NOTE: DOOR PART CHANGES IN 1979 AND 1983, 3566 Support channel for door glass regulator for passenger RHside roll up window glass 400mm long. Used with Part 89 & 90. Suit early styled cabs. 53.50 3567 Support channel for door glass regulator for driver side LH roll up window glass 400mm long. Suit early styled cabs. 53.50 LATE MODEL WINDOW REGULATOR 3538 Regulator assembly LH. (Later model - post 83) 138.00 3539 Regulator assembly RH. (Later model - post 83). 138.00 3541 Screw for regulator assembly above. 4 Per Door. Price Per Each. 1.00 3540 Retaining ring for regulator to glass support track. Price Per Each. (Suit 3538 & 3539) Bin 2914. 3.60 3545 Linkage remote door. Connects handle to door lock. Used with part No 3538 & 3539 68.00 LATE MODEL WINDOW SUPPORT 3535 Support window RH model. Used with Part 3538-450mm long. 89.00 3536 Support window LH model. Used with Part 3539. 450mm long. 89.00 WINDOW REGULATOR HANDLE 3525 Window regulator handle, early R&F. See part no 3526 & 3527 for escutcheon & pin..page 2. Note Part No 3531 below has more clearance. 3531 Window regulator handle. Suit doors with Western Trim or worn Shafts. 50.00 72.00 R MODEL-5 DOORS
SECTION 5 - R MODEL - DOORS PLEASE NOTE: DOOR PART CHANGES IN 1979 AND 1983, DOOR LATCH EARLY TO 1979 3553 Latch door early RH, suit R & F, MIR, MBR 275.00 3554 Latch door - early LH. Suit R & F, MIR, MBR. 275.00 DOOR LATCH AFTER 1979 R & F 3542 Latch door late RH. Used with part no. 3545. Mack current style DM, R, RB, RD. 84.00 3543 Latch door- late LH. Used with part no. 3545. Mack current style DM, R, RB, RD. 84.00 DOOR LATCH SCREWS 3517 Door latch holding screws. 3 Per Door - 1/4 inch. PRICE PER EACH... Bin 2900 1.82 DOOR STRIKER - EARLY R & F 3555 Striker Plate - RH. Mack early style R, RB, RD, DM. 153.00 3556 Striker Plate - LH. Mack early style R, RB, RD, DM. 153.00 3559 Striker Plate RH - used with part no. 3560. Mack current style R, RB, RD, DM. 44.00 3560 Striker Plate LH. used with part no. 3560. Mack current style R, RB, RD, DM. 48.00 R MODEL-5 DOORS
SECTION 5 -R MODEL - DOORS KEY DOOR LOCKS 856 Door & ignition lock set, includes 2 door tumblers and one ignition tumbler with 2 matching keys. New. SEE GENERAL SECTION 6E-2 FOR PRICING Bin 88 DOOR LOCK RETAINER CLIP 2912 Door lock slide in retainer clip. Slides from outside inner door to hold door lock in place. - New. Bin 2914 11.50 BAILEY CHANNEL 3549 Channel Bailey R&F. 2 per door. Price Per Each. Supplied with 5 clips. See Rubber Parts in General Section 6G-8 for Pricing. WINDOW WEATHER FELT STRIP 3550 Weather strip R & F model door glass sqeegee guides.- 1 required per door L & R. Price Per Each.see Rubber Parts in General Section 6G-8 for Pricing. WINDOW WEATHER STRIP WITH RUBBER SEAL 3546 Weather strip R&F model door glass squegee guides with rubber wiper seal and door lip - RH (one per door) 45.50 3547 Weather strip R&F model door glass squegee guides with rubber wiper seal and door lip (one per door) - LH 45.50 SPECIAL DOOR SEAL 3558 Rubber super soft hollow door seal. Adhesive backing. Fits in cabin door, closes against it.. 13mm wide 18mm high, sold in a 4.5m (15ft) length. See Rubber Parts in General Section 6G-9 for Pricing. MIRROR ARMS 3575 Kit mirror bracket RH stainless. 204.00 3576 Kit mirror bracket LH stainless. 204.00 MIRROR HEAD 3577 Mirror head-mack. LH alloy type with bulldog but no heating or light. See 803 General Electrical Section for light in photo 3578 Mirror head-mack. RH alloy type with bulldog but no heating or light. 229.00 229.00 R MODEL-5 DOORS