PowerPoints & s Light Duty Portable Welded Insulation Fastening Solutions www.gripnail.com 800-474-7624 Heavy Duty Portable Fixed Head Gliding Head Local Gripnail Distributor Gripnail Corporation An Employee-Owned Company 97 Dexter Road East Providence, RI 02914 Tel: 401-431-1791 or 800-474-7624 Fax: 401-438-8520 Email: gripnail@gripnail.com Web: www.gripnail.com ISO9001:2000 Registered Multi Head High Speed
7100 Light duty, portable hand welder The Model 7100 hand welder is a solid state resistance welder designed specifically for welding PowerPoint Resistance Weld Pins to galvanized sheet metal ductwork. Its lightweight and extra-long gun lead makes it perfect for shop or field use. The complete system includes the power pack with adjustable timer, lightweight gun with heavy duty weld/control leads, and a heavy-duty ground lead with spring loaded copper alloy clamp. Lightweight welder with powerful transformer Welds 12 pins per minute Works best with 24 gauge sheet metal, satisfactory results with heavier metal 7100 Dimensions Cables Weight 190-240 VAC 60Hz, 1 Phase, 30 Amp 16 L x 9 5/8 W x 7 1/4 H Gun: 10 1/2 feet; Ground: 2 1/2 feet 74 pounds 7200 Heavy duty, portable hand welder The latest addition to the Gripnail line, the Model 7200 hand welder is a solid state resistance welder designed for use with 16 gauge sheet metal and PowerPoint Resistance Weld Pins. The compact size and hand truck feature allows for easy portability in the field or around the shop. A light weight pistol grip trigger, ergonomic handle and easy to read controls further simplify operation. The rugged construction and powerful transformer stand up to the demands of constant, heavy use. Fast weld cycle Portable wheels/hand truck Capable of welding up to 2 pins with 16 gauge metal 7200 190-240 VAC 60Hz, 1 Phase, 35 Amp Dimensions (including handle) 16 3/4 L x 18 1/4 W x 46 1/2 H Cables Gun: 15 feet; Ground: 5 feet Weight 140 pounds
7005 & 7005 RF New and improved for super strong welds and dependable operation Gripnail s 40-plus years of insulation fastening experience have produced a welder for the most severe duct manufacturing environments. The 7005 pin welder features simple, reliable electronic controls and a high output transformer that will fasten 1/2 to 2 pins to 16-26 gauge sheet metal. Other features include: Dependable Electronic Controls - A PLC (programmable logic control) unit replaces all timers, relays, reed switches and circuit boards Single Weld Control - Just set the machine for the gauge you want, and everything else is automatic Quick Change Welding Tips - Upper and lower tips can be changed in seconds; lower tip is reversible for twice the life Automatic Pin Feed - One feeder bowl for all pin sizes 7005 190-240 VAC 60Hz, 1 Phase, 35 Amp 2-3 CFM, 80 PSI Air Requirement Working Depth 63 Anvil Height 36 Dimensions Total Depth: 68 Width: 32 Simple Controls allow operation of this machine by workers of varying skill levels. Both our standard Power Pinner 7005 and 7005 RF have an integrated weld and dwell time setting so that the operator need only turn the weld setting up for longer pins or thicker metal. The only other controls are a rapid-fire on/off switch and a feeder bowl speed control. There is also an LED voltage display to alert the operator to low voltage situations. The Rapid Fire (RF) option allows the operator to continuously fasten weld pins at a rate of one pin every 2 seconds without taking their foot off the pedal. This maximizes the machine speed for the fastest possible pinning operation. Flip the switch and the machine returns to the manual mode for larger pieces of duct.
Glider 7105 & 7105 RF The power and simplicity of our 7005 with a movable weld-head Contractors who regularly line large fittings and straight duct will find the convenience of the Glider speeds their assembly and reduces their fabrication costs. The weld head travels a full 60 inches for lining 5-foot wide duct. The head is moved with a multi-position extension arm and glides on specially designed bearings. A weld pin is set each time the operator squeezes the pistol grip s trigger. Small duct sections can be easily lined by locking the weld head in the forward position, moving the extension arm to its vertical position and activating the foot pedal. The Rapid Fire (RF) option works when the arm is locked in the vertical position and the machine is foot pedal activated. This allows the operator to continuously fasten weld pins at a rate of one pin every 2 seconds without taking their foot off the pedal. A programmable logic control unit replaces all timers, relays, reed switches and circuit boards LED voltage readout alerts operator to low voltage situation Glider 7105 Simple, logical controls reduce operator training Frame cutouts permit continuous lining of flat or L section flanged duct the lower weld tip is reversible for easy maintenance and extended life. Air Requirement Working Depth 60 Anvil Height 36 190-240 VAC 60Hz, 1 Phase, 35 Amp 2-3 CFM, 80 PSI Dimensions Total Depth: 71 Width: 32 Moving head speeds production The operator moves the drive head along the length of the machine and applies a weld pin whenever he squeezes the trigger.
Hi Speed 50 Full speed coil line pinner Most coil lines are capable of running at 50 feet per minute but have to slow down to 25 when applying welded duct liner fasteners. The 50 keeps your line speed and profits up. Run your line at its full 50 foot per minute capacity while placing pins as close as 6 inches apart. The Hi Speed 50 is equipped with one set of specially designed feeder bowls that handle pins from 1/2 inch to 2 inches. In addition, the high output transformer will weld the full range of pins to metal as thick as 16 gauge. Runs at 50 foot per minute coil line speed Welds 1/2 inch to 2 inch pins to 26 through 16 gauge metal Five or six head models available May be purchased as part of a new coil line or as an addition to an existing line Drop in replacement for older welders Hi Speed 50 Machine Operation The Hi Speed 50 and the coil line s insulator are connected with a simple chain drive. This drive powers the heads forward at the same speed as the sheet metal, whenever the machine is pinning. As soon as the machine stops pinning, air cylinders move the drive heads back towards the insulator. The PLC optimizes the head travel so that full ten-foot sheets may be insulated with pins on six-inch centers. The split pin track keeps a reserve of pins ready to load in the lower track every time the heads return to the starting position. Air Requirement Pass Height 36 190-240 VAC 60Hz, 3 Phase, 100 Amp 5 CFM, 80 PSI Dimensions Total Depth: 48 Width 5-head 78, 6-head 90 Simple Controls A single weld-setting switch controls the weld time for all heads while the PLC optimizes the dwell time. Operators only need to increase the weld setting for longer pins or thicker sheet metal. Each head has an on/off switch so that the machine can accommodate narrower coils of sheet metal. Fewer Components Inside the control box is a PLC (programmable logic control) which controls the load cylinders, drive cylinders, and drive head travel. Mounted on the door of the control box, for easy servicing, are the on/off switches, feeder bowl control switches and the weld-setting switch.
PowerPoint Weld Pins Quality pins cost less PowerPoint weld pins save time and money because they perform consistently. Each point is precisely formed to provide optimum electrical resistance and each cap and shank assembly is securely swaged so that pins will feed without jamming, even in older welders. In addition, PowerPoints are shipped in plastic buckets to eliminate shipping damage. The result is continuous production without the expense of having to clear track jams or refasten where pins did not hold. Faster Welds - forged diamond point design creates more electrical resistance for faster welds Super Sharp Point - 22 degree point is the sharpest in the industry and cleanly pierces the toughest duct liner Beveled Edge Cap - prevents tearing of duct liner Better Plating - zinc and chromate plating exceeds SMACNA standards and gives a more professional appearance More Consistent Feeding - precise assembly of shanks and caps along with a smoother plating reduces feeding problems in tracks of automatic equipment PowerPoint Weld Pins Applied With Standard Equipment - easily applied with most standard hand held or hopper fed resistance welders Ordering Information Product Recommended For Pin Length Packaging Before Welding #057 1/2 insulation - all densities 0.501 Bulk or Standard #107 1 insulation - 1 1/2 lb. density 0.685 Bulk or Standard #127 1 insulation - 3 lb. density 0.936 Bulk (5,000 pcs./bucket) #137 1 1/2 insulation - all densities 1.118 Bulk (3,000 pcs./bucket) #157 2 insulation - 1 1/2 lb. & 2 lb. density 1.490 Bulk (3,000 pcs./bucket) #207 2 insulation - 3 lb. density 1.916 Bulk (3,000 pcs./bucket) Manufactured With Pride In The USA - to ISO9001:2000 quality control standards PowerPoints are packaged in plastic buckets. Bulk packaging is 5,000 pieces per 5 gallon bucket (except as noted). Standard packaging is 4,000 pieces per carton (4 buckets/1,000 pieces each). GRIPNAIL Serving the HVAC Industry for over 40 Years Gripnail Corporation was started in Providence, Rhode Island in 1965. Gripnail has grown by listening to HVAC contractors and distributors. This has led to continuously improving products, manufacturing methods and product distribution. All fasteners and application machinery are manufactured in East Providence, Rhode Island to ISO9001:2000 quality standards. In 2004, Gripnail became a 100% employee owned company. Everyone at Gripnail recognizes the importance of our products in your operation and strives to make certain that you are completely satisfied with your purchase of fasteners and machinery. We appreciate your business and look forward to including you in our long list of satisfied customers. 2009 Gripnail Corporation. All Rights Reserved.