BACKWARD INCLINED FANS

Twin City an INDUSTRIAL PROCESS AND COMMERCIAL VENTILATION SYSTEMS BACKWARD INCLINED ANS BC-SW BC-DW CATALOGUE M00 AUGUST 0

BACKWARD INCLINED ANS Models BC SWSI & BC DWDI BC DWDI Arrangement Refer to Catalogue 0 for Model BAE (aerofoil impeller) SWSI and DWDI fans. Refer to Catalogue 600 for Ventilating Sets featuring Model BC (designated as BCV) and C (CV) fans in Arrangement. Refer to Catalogue 0 for Model BAV (aerofoil impeller) ventilation sets in Arrangement. Model BC SWSI & BC DWDI is available with UL/ CUL 0 listing, for electrical, ile No. E8680. This catalogue features Model BC non-overloading centrifugal fans in SWSI (single width, single inlet) and DWDI (double width, double inlet) design. BAE aerofoil fans offer a slightly higher efficiency and less noise than BC fans at a price premium of about %. However, the hollow aerofoil blades are more susceptible to erosion by particulate matter in the airstream than BC blades and thus Model BAE is recommended for clean air applications only. Both designs are a popular choice for the efficient handling of large volumes of relatively clean air at low to moderate pressures in applications such as: HVAC (heating, ventilating and air conditioning) Combustion air supply iltration and drying systems ume hood and spray booth and other exhaust systems Air pollution control (clean side of dust collectors) Industrial processes Please discuss your particular application with the Twin City an & Blower representative for your area. Twin City an & Blower has established itself as a leader in the design and manufacture of quality air moving equipment and continues to advance by implementing a philosophy that stresses quality in all of its operations. Our products are known for their rugged construction and reliability of operation. Twin City an & Blower offers flexibility in design and construction of fans coupled with superior service before and after the sale. Model BC SWSI Sizes mm to,49 mm impeller diameters Performance Airflow to m /sec Static pressure to 4,9 Pa Arrangements Available in Arrangements,, 4, 8, 9, 9, Twin City an & Blower certifies that the Model BC SWSI and BC DWDI fans shown herein are licensed to bear the AMCA Seal. The ratings shown are based on tests and procedures performed in accordance with AMCA Publication and comply with the requirements of the AMCA Certified Ratings Program. Refer to Catalogue 06 for sound power levels. Model BC DWDI Sizes mm to,49 mm impeller diameters Performance Airflow to 6 m /sec Static pressure to,480 Pa Arrangements Available in Arrangements, TWIN CITY AN - CATALOGUE M00

CONSTRUCTION EATURES Impeller Construction Type BC impellers are constructed of steel using flat single thickness blades, solid welded to the rim and back plate. The inlet-side rim is designed as a proper companion for the inlet cone. Note that the use of a conical spun shroud (rim) makes BC fans less susceptible to the performance losses associated with poor inlet conditions. All BC impellers are statically and dynamically balanced to grade G6. (.8 mm/s rms peak or less) for smooth operation prior to being assembled in the fan, followed by final balance of the entire rotating assembly. Housing Construction All fan housings are continuously welded to provide strength and durability for extended service life a necessity in all commercial and industrial installations. All SWSI fans and DWDI Class III and IV fans feature an outlet flange for duct connection as standard. DWDI Class I and II fan outlets are designed for slip-on joint connection. A flanged outlet is available as an option. Inlet collars for slip-joint connections are standard on all SWSI fans. Lifting lugs are standard on all fans. All housings are reinforced with rigid bracing to increase structural integrity. The support angles are intermittently welded and caulked between welds to prevent bleedthrough corrosion. Precisely positioned cut off plates and aerodynamically spun inlet cones provide high efficiency and smooth airflow through the fan. BC SWSI Impeller All fans are available in standard discharge configuration (see page 8). SWSI fans Class I and II, sizes 0 and smaller in Arrangements, 4, 9 and are field rotatable to any standard discharge position. To help reduce overall heights, all DWDI fans feature a nonrotatable housing design as standard. Shaft Shafts are AISI Grade 40 or 4 hot-rolled steel accurately turned, ground, polished, and ring gauged for accuracy. Shafts are generously sized for a first critical speed of at least.4 times the maximum speed for the class. BC DWDI Impeller Bearings Bearings are heavy duty, grease lubricated, spherical roller or adapter mounted anti-friction ball, self-aligning, pillow block type, selected for minimum average bearing life L- in excess of 40,000 hours at the maximum fan RPM. Twin City an Mechanical Run Test & inal Vibration Check All fans are assembled for a mechanical run test and final balance prior to shipment. Vibration readings are taken on both fan bearings in the axial, horizontal, and vertical directions at the specified speed. ans are balanced to.8 mm/s rms peak or less.

SWSI ARRANGEMENTS Arrangement fan with optional unitary base, horizontal split housing, shaft and V-belt drive guard. Arrangement SWSI Single Width, Single Inlet Arrangement fans are usually belt driven. The impeller is overhung on the shaft, i.e., mounted at the end of the shaft. The motor can be mounted in any of the four AMCA standard motor positions, W, X, Y, or Z. The two fan bearings are mounted on the bearing pedestal, out of the airstream. Arrangement fans are thus recommended for high temperature or contaminated air applications. Belt driven configurations offer performance flexibility. If the performance requirements change after the fan has been installed, it is simple and inexpensive to change the drive. Extended lube line at inlet standard on all Arrangement fans. Arrangement SWSI Single Width, Single Inlet Arrangement is available in belt driven only. Arrangement SWSI has one bearing located in the airstream. The impeller is mounted between the bearings and supported by the fan housing, which makes it a structurally sound, compact, and economical arrangement. Arrangement 4 SWSI Single Width, Single Inlet Arrangement 4 is available in direct drive only. The fan impeller is mounted directly on the motor shaft with the motor mounted on a pedestal. An Arrangement 4 design offers low maintenance as there are no fan bearings, fan shaft or drive parts to maintain. Arrangement 4 is typically limited to size 6 or smaller. Direct drive Arrangement 4 with bolted access door and shaft seal. Typical Direct Drive Speeds 60 Hz OPERATION 0 Hz OPERATION Synchronous ull Load Synchronous ull Load Speed Speed Speed Speed 600 00 000 900 0 40 0 00 9 900 80 0 The actual full load speed of the motor can vary slightly depending upon motor HP and motor design. Arrangement 8 fan with optional coupling. Arrangement 8 SWSI Single Width, Single Inlet Arrangement 8 is a modified version of Arrangement used for direct drive. The Arrangement bearing pedestal is extended to accommodate the motor. A flexible coupling connects the fan and motor shaft. Refer to the typical direct drive speeds under Arrangement 4. Recommended for 8 kw and larger applications. 4 TWIN CITY AN - CATALOGUE M00

SWSI ARRANGEMENTS Arrangement 9 SWSI Single Width, Single Inlet Arrangement 9 is available as belt driven only. A motor slide base is mounted on the side of the bearing pedestal. This arrangement permits the unit to ship as a complete assembly with the motor and drive mounted. Typically, the motor is mounted on the left side of the pedestal for CW rotation fans and on the right side for CCW rotation fans. Arrangement 9 SWSI Single Width, Single Inlet (Not Shown) Arrangement 9 is available when a unit requires a motor that is too large to mount on the side of the bearing pedestal. The fan base is extended to accommodate the motor, for horizontal mounting, similar to an Arrangement fan. Typically, the motor is mounted on the left side of the pedestal for CW rotation fans and on the right side for CCW rotation fans. Arrangement 9 is not suitable for mounting vibration isolators directly under the fan. an shown is Arrangement 9 CW-THD with nonstandard motor location on right-hand side. Arrangement SWSI Single Width, Single Inlet Arrangement is available as belt driven only. or Class I and II fans, sizes through 6, Arrangement units are commonly referred to as Ventilating Sets. (Refer to Catalogue 600 for more details.) An Arrangement unit has an adjustable motor base mounted inside the bearing pedestal. This arrangement offers a more compact design than the Arrangement 9 and is suitable for roof or outdoor installations with a weather cover. Class II Arrangement ventilating set with optional shaft cooler and insulated heat shield. DWDI ARRANGEMENTS Arrangement DWDI fans are generally supplied in Arr. for V-belt drive. The impeller is mounted between the bearings and supported by the fan housing. Since both bearings are located in the airstream, standard DWDI fans should be used for clean air applications with air temperatures limited to 4 o C. The motor can be mounted in any of the four standard motor positions: W, X, Y or Z. Arrangement Arr. offers an integral extended base to accommodate the motor. The base is pre-punched to accept vibration isolators. Arr. is available to Size 660 and for motor positions W and Z as standard. or motor positions X and Y, consult factory. Arr. with motor located in Z position.

OPTIONAL CONSTRUCTION Split Housings All fans are designed to permit impeller removal through the fan inlet. To suit installation as well as transportation requirements, Twin City an & Blower offers horizontal split, pie-shaped, as well as other special split housing designs. Pie-shaped split housings allow fan impeller and shaft removal without disconnecting ductwork. an with pie-shaped split housing with bolted access door Swingout Construction Swingout fans are ideal for applications requiring frequent cleaning and inspection of the fan impeller and interior of the housing such as found in spray painting booth exhaust. Refer to Catalogue GA00 for other types of easy access fans offered by Twin City an & Blower. Spark Resistant Construction an applications may involve the handling of potentially explosive or flammable particles, fumes or vapours. Such applications require careful consideration by the system designer to insure the safe handling of such gases. Twin City an & Blower offers the following classifications of spark resistant construction per AMCA Standard 99-040-86. It is the specifier or the user s responsibility to specify the type of spark resistant construction with full recognition of the potential hazards and the degree of protection required. Type A All parts of the fan in contact with the airstream must be made of non-ferrous material usually aluminium and limited to C operation. Type B The fan shall have a non-ferrous impeller and non-ferrous ring about the opening through which the shaft passes usually aluminium impeller and anti-spark track and limited to C construction. Type C The fan shall be so constructed that the shift of the impeller or shaft will not permit two ferrous parts of the fan to rub or strike. This is accomplished with an aluminium inlet cone and anti-spark track. This construction is limited to 0 C Construction to 4 C is available using a steel inlet cone with copper/ bronze lining.. Bearings shall be placed outside the airstream. Therefore, do not use Arrangement or.. The user shall electrically earth all fan parts. R e f e r to the above listed AMCA standard for full details. Special Metals To suit the demanding applications of today s industry, Twin City an & Blower offers a variety of material for construction, including aluminium and stainless steel. We offer AWS and ASME certified welding procedures and welding technicians to assure quality construction when using special metals as well. 6 TWIN CITY AN - CATALOGUE M00

OPTIONAL CONSTRUCTION High Temperature Modifications Construction Standard fan design options are available to handle airstream temperatures to 4 C. Consult your Twin City an & Blower representative for applications over 4 C. The fan bearings should be kept outside of the hot airstream and below 4 C ambient. High temperature operating limits, available arrangements, and necessary modifications are shown in Table. Shaft Cooler and Shaft Seal Table. High Temperature Construction Requirements TEMPERATURE TYPE O OTHER LUBRICATION ( C) BEARING REQUIREMENTS 8 C to +48 C Ball or Roller Grease Standard an 48 C to 60 C Ball or Roller Shaft Cooler, Shaft Seal. or High Temp. with () Expansion Arr. 9 & ans, a Motor Grease Bearing Heat Shield is Included. 60 C to 46 C High Temp. Aluminum Paint Ball or Roller High Temp. Shaft Cooler, Shaft Seal. or with () Expansion Grease Arr. 9 & ans, a Motor Bearing Heat Shield is included. AVAILABLE ARRANGEMENTS Arr., 8, 9, 9, Arr. and to 4 C Arr. 4 to 8 C Arr., 8, 9, 9, Arr., 8, 9, 9, (Arr. 9 & Limited to C) Derating actors or High Temperature an operation at high temperature adversely affects the strength of fan impellers. As a result, the maximum safe speed must be derated by the factors shown in Table. Example: Maximum safe speed at C for a size 6 BC, SWSI, Class II steel impeller = 0.86 x 8 = RPM (8 RPM is maximum RPM at C). Table. Derating actors or High Temperature TEMPERATURE ( C) STANDARD STEEL STAINLESS STEEL 0.00.00 9 0.99 0.9 0.98 0.9 0.98 0.9 0 0.96 0.88 60 0.9 0.84 0.90 0.8 0 0.80 0.8 4 0.60 0. 480 0. 0.0 Twin City an

STANDARD CONIGURATIONS Designation for Rotation and Discharge Clockwise Clockwise Clockwise Clockwise Counterclockwise Counterclockwise Counterclockwise Counterclockwise Upblast Top Angular Up Top Horizontal Top Angular Down Upblast Top Angular Up Top Horizontal Top Angular Down CW 60 CW4 CW90 CW CCW60 CCW4 CCW90 CCW Clockwise Clockwise Clockwise Clockwise Counterclockwise Counterclockwise Counterclockwise Counterclockwise Downblast Bottom Angular Down Bottom Horizontal Bottom Angular Up Downblast Bottom Angular Down Bottom Horizontal Bottom Angular Up CW 80 CW CW0 CW CCW80 CCW CCW0 CCW Direction of rotation is determined from drive side of the fan. On single inlet fans, the drive side is always considered the side opposite the fan inlet. On double inlet fans with drives on both sides, the drive side is that with the higher power drive unit. The direction of discharge is determined in accordance with the diagrams shown above. The angle of discharge references the vertical axis of the fan and is designated in degrees above or below that reference axis. On fans inverted for ceiling suspension or side-wall mounting, the discharge is determined when the fan is resting on the floor. Motor Positions The drawing above illustrates the AMCA motor position standards for Arrangement and fans (Arrangement shown). The location of the motor is determined by facing the drive side of the fan and designating the motor position by letters W, X, Y, or Z, in accordance with the diagram shown above. Illustrations reprinted from AMCA Publication 99 Standards Handbook, with the express written permission from the Air Movement and Control Association International, Inc., 0 West University Drive, Arlington Heights, IL 60004-98. 8 TWIN CITY AN - CATALOGUE M00

ACCESSORIES Volume Control Devices Outlet dampers, variable inlet vanes, and variable frequency drives are three popular devices used to control volume for fan systems. Variable Inlet Vanes Variable inlet vanes cause the entering air to spin in the direction of impeller rotation, resulting in reduction in volume, static pressure and absorbed power and thus providing an infinite number of fan curves approximately parallel to the original fan curve. Variable inlet vanes cost about 0% to 80% more than outlet dampers but offer significant savings in energy. Because of their simplicity, inlet vanes can be more reliable when compared to variable frequency drives. There are two types of variable inlet vanes: nested (internal type) and bolted on (external type). Nested Inlet Vanes External Inlet Vanes Nested inlet vanes are built into the fan inlet cone and offer the advantage of saving space and lower cost as opposed to the external type, and they may be provided on all fan sizes 6 and larger. Twin City an & Blower offers cantilevered vanes to size 0 Class II fans to minimize insertion losses and noise associated with centre hub design. External inlet vanes are bolted to the inlet of the fan and are available as standard to size. Use of external vanes should be considered for hostile environments since operating linkages are shielded from the airstream. Both types of inlet vanes are available to C construction. Outlet Dampers The closing of the damper adds to the resistance that the fan is working against. This moves the operating point to the left of the initial rating point. The savings in power depends on the relative position on the fan curve and is usually much less than offered by other methods. Outlet dampers are typically the least expensive option and should be considered when infrequent operation at lesser capacity is desired or when handling hot, humid or particulate laden air. PRESSURE STATIC PRESSURE 8 6 4 0 0 Performance Curves at Different Vane Settings 0 0 0 4 6 8 CM IN LOW 000's System Curve SP @ Vane Setting BHP @ Vane Setting 0 0 00 60 80 40 BRAKE HORSEPOWER There are two types of outlet dampers: parallel blade and opposed blade. Parallel blade dampers are recommended for systems where air volume is modulated between fully open to about % of open. Opposed blade dampers cost about % more and are recommended for systems where volume is modulated over the entire range. Opposed blades reduce air volume in a closer relationship to the control arm movement. Variable requency Drive (VD) an Motors VD changes the fan speed and can provide the greatest potential for energy savings, although at highest initial cost. VD should be considered for extended operation at part load conditions, especially below 0% of the full volume operation. Parallel Blade Outlet Damper Opposed Blade Outlet Damper 9

ACCESSORIES Belt Guards A belt guard protects personnel from the moving drive parts. Both standard and totally enclosed type guards are available. Belt, Bearing and Shaft Guard Shaft and Bearing Guards (SWSI) Solid sheet metal guards cover shaft and bearings and come with extended lube lines to a common point out either side of the guard. A guard spanning the shaft between the bearings is also available to provide easy access to bearings for lubrication and vibration monitoring. Unitary Base A structural steel base provides common support to fan, motor and drive including guards. This style of base is designed for use without isolators and requires adequate foundation integrity for proper operation. Vibration Isolation Bases Heavy structural base for fan, motor and drive is designed for use with spring or rubber-in-shear type isolators. Use of flexible connectors at inlet and outlet is required on fans with isolators. Unitiary Base Shaft Coolers V-Belt Drives V-belt drives offer an economical yet flexible means of transmitting power to the fans. There are two types of V-belt drives. Adjustable Pitch or Variable Speed Drives An adjustable pitch drive offers easy adjustment of speed. The motor pulley pitch can be adjusted when the fan is at rest which can offer speed variation of about % from the design speed. This style of sheave can result in higher vibration so adjustable pitch drives are not recommended for use on motors over. kw or wherever low vibration is required. ixed Pitch or Constant Speed Drives This type of drive offers low cost and lowest vibration levels. Speed change can often be accomplished by changing only one of the sheaves. Bearing Upgrades Unit roller or split pillow block, double row roller bearings are available. Split pillow block roller bearings are not available for fans with less than mm diameter bearings and are not recommended for fans with light loadings. Refer to an Engineering Data E-0 and E-0 for the correct type of bearings, selection criteria, maintenance, etc. Shaft Cooler or Heat Slinger A cast aluminium shaft cooler is recommended to dissipate the heat and protect the fan bearings for all applications over C. (Refer to picture on page.) TWIN CITY AN - CATALOGUE M00

ACCESSORIES Special Paint & Protective Coatings Twin City an & Blower has an in-house, specialty coating facility to handle any type of coating requirement. Refer to Engineering Supplement ES- for more details. Access Doors Bolted, quick opening, and raised bolted access doors are available for impeller inspection or maintenance. Drain Threaded pipe coupling welded to the lowest point in the housing scroll. All fans come with a drain hole in the bottom of the housing. Shaft Seal A shaft seal reduces leakage and protects the bearings from a contaminated airstream. It is constructed of non-asbestos woven fibrous materials (ceramic felt) compressed between an aluminium cover plate and the fan housing. A ceramic felt shaft seal does not make the fan air tight. A variety of special seals are available for low leakage applications requiring more positive protection, including mechanical type stuffing boxes. (The picture on page shows a standard seal.) Quick-Open Access Door Bolted Access Door Raised Bolted Access Door langed Inlet A punched inlet flange is available for duct mounting. Drain Shaft Seal langed Outlet (DWDI Class I & II) A punched or un-punched flange is welded to the fan outlet. An un-punched flanged outlet is standard on all SWSI and DWDI Class III and IV fans. Inlet/Outlet Companion langes Companion flanges are used for installing the fan to flexible sleeve connections and are punched to match the fan s inlet or outlet. Inlet and Outlet Screens Safety screens are available for mounting in the fan inlet or outlet in non-ducted applications. Other Accessories Available Variation in impeller diameter and width Inlet boxes Bearings RTD Piezometer ring airflow measuring system Consult factory for other accessories Safety Screen Companion Inlet lange Twin City an

LOW MEASUREMENT SYSTEM Piezometer Ring (Airflow Measuring System) A piezometer ring is available on model BC fans, as well as other Twin City an housed and plenum fans, as part of an airflow measuring system, based on the principle of a flow nozzle. The inlet cone of the fan is used as the flow nozzle. The flow can be calculated by measuring the pressure drop through the inlet cone. No tubes or sensors are inserted in the high velocity airstream which could obstruct airflow. The system, consists of a piezometer ring mounted at the throat and a static pressure tapping mounted on the face of the inlet cone. A differential pressure transducer and digital display can also be provided. The pressure drop is measured from the tapping located on the face of the inlet cone to the piezometer ring in the throat. The inlet tapping is connected to the high-pressure side of the transducer and the piezometer ring is connected to the low-pressure side. Piezometer Ring Mounted at Throat of Inlet Cone Based on Twin City an laboratory tests, the system was determined to be accurate within +/-%. Refer to Twin City an Engineering Supplement ES-. NOTE: Twin City an does not recommend placement of flow measuring probes inside the fan inlet cone in the path of airflow. These devices create disturbances and unpredictable performance losses. Twin City an will not be responsible for loss of performance due to such devices. The performance curves in this catalogue are based on fans handling standard air at a density of. kg/m. This is equivalent to air at C at sea level (. kpa barometric pressure). When specified performance is at a density different than standard, it must be Table. Temperature and Altitude Density Ratios AIR TEMP C an Selection Guidelines converted to the equivalent standard conditions before the fan can be selected from the performance curves. The equivalent standard conditions can be calculated by using the Temperature and Altitude Density Ratios shown in the table below. ALTITUDE IN METRES ABOVE SEA LEVEL 0 00 600 900 0 0 000 400 00 400 BAROMETRIC PRESSURE IN kpa. 9. 94. 90.9 8. 84. 8.99 9.49.6.9 6.6. -40.8.4..9.089.00.08 0.98 0.99 0.89 0.86 0. -0.8..08.040.00 0.966 0.9 0.909 0.864 0.8 0. 0.660.0 0.999 0.96 0.99 0.896 0.864 0.88 0.8 0. 0. 0.6 0.90 0.000 0.96 0.9 0.898 0.866 0.8 0.809 0.8 0.46 0. 0.649 0.0 40 0.96 0.90 0.8 0.840 0.8 0.8 0. 0.4 0.699 0.664 0.608 0. 6 0.86 0.8 0.80 0.8 0. 0.4 0.0 0.680 0.64 0.6 0.6 0.494 0 0.86 0.8 0. 0.06 0.680 0.66 0.66 0.6 0.8 0.8 0. 0.448 0.6 0. 0.68 0.66 0.6 0.64 0.96 0. 0.49 0. 0.48 0.49 0.69 0.669 0.64 0.6 0.600 0.8 0.6 0.44 0. 0.49 0.40 0.9 0.64 0.6 0.609 0.8 0.66 0.46 0.9 0. 0.488 0.464 0.44 0. 00 0.69 0.9 0.6 0.6 0.6 0. 0.0 0.486 0.46 0.49 0.40 0. 0.88 0.6 0.4 0.8 0.09 0.49 0.46 0.46 0.49 0.4 0.8 0. 0 0.60 0.40 0. 0.0 0.48 0.46 0.4 0.49 0.48 0.9 0.6 0.9 0. 0.6 0.498 0.480 0.46 0.446 0.4 0.40 0.99 0.80 0.4 0.0 00 0. 0.49 0.46 0.49 0.44 0.46 0.44 0.40 0.8 0.6 0. 0.9 0 0.40 0.44 0.48 0.4 0.40 0.9 0.80 0.69 0. 0.4 0.0 0.68 0.4 0.46 0.4 0.406 0.9 0. 0.66 0. 0. 0. 0.9 0.8 400 0.4 0.40 0.40 0.9 0. 0.6 0. 0.4 0. 0.09 0.8 0.48 4 0.40 0.40 0.9 0. 0.64 0.0 0.40 0.0 0. 0.98 0. 0.9 40 0.40 0.9 0. 0.64 0. 0.8 0.8 0.8 0.0 0.8 0.6 0. 00 0.9 0.66 0. 0.40 0.8 0.6 0.0 0.9 0.8 0.69 0.46 0.6 0 0.6 0.44 0. 0.0 0.08 0.9 0.88 0.9 0.66 0. 0. 0.0 600 0.6 0.4 0. 0.0 0.9 0.80 0. 0.64 0. 0.8 0.8 0.9 Example Assume a 6 BC SWSI fan to handle. m /sec, 6 Pa SP, at C and 900 m altitude.. or the operating conditions of C and 900 m altitude, the factor can be found in Table to be 0.6.. Divide the operating SP by this factor. Thus, 6 Pa 0.6 = 0 Pa SP, which is the equivalent static pressure at standard air density.. rom the 6 BC SWSI performance curve find the fan RPM and absorbed power for. m /sec and 0 Pa SP to be 89 RPM and 9.6 kw (by interpolation) at standard conditions. 9.6 kw is also referred to as cold or starting absorbed power. To determine the absorbed power at operating conditions, multiply the absorbed power at standard conditions by the factor from Table (9.6 x 0.6 = 6.0 kw). The absorbed power at operating conditions is 6.0 kw. TWIN CITY AN - CATALOGUE M00

ENGINEERING DATA BC SWSI AN SIZE MAX. RPM Maximum RPM, Impeller Weights & WR (moment of inertia in kg-m ) CLASS I CLASS II CLASS III CLASS IV IMPELLER IMPELLER IMPELLER IMPELLER WEIGHT WEIGHT WEIGHT WEIGHT WR (kg-m ) MAX. RPM WR (kg-m ) MAX. RPM WR (kg-m ) MAX. RPM WR (kg-m ) (kg) (kg) (kg) (kg) 6 6.8 0.0 49 6.8 0.0 08 0. 608.4 0. 84. 0. 8 8. 0. 46. 0.6 099. 0.6 8 9. 0.6 64 9. 0. 4 4. 0.4 480.0 0.4 6.9 0.4 08. 0.9 86. 0. 46 6.8 0. 8 8 4. 0. 9. 0.46 4 4. 0.9 66 4. 0.9 00 9. 0. 490. 0. 69 8.6 0.8 44 4.. 0.0.0 8.6. 848 8.6. 088 44.. 4 6.8.6 0 9..8 8 0.0. 808 9..8 0 9 4..4 80 46.8. 8 60.0. 44 69. 4. 00.4. 6 6.8 4. 09 8..9 9 8.. 0 4 68.6 6. 4.9 6. 8 9. 9. 08 9. 8.4 6 99 90.0. 8 9..0 4. 88. 40 90. 6 6. 66 8.4 6 8.4 44 8.9 8 9. 46 8 8. 4 0. 490 4 9 4.4 96 0 4. 86 4. 40 0 0.4 4 60 0.9 86 46 8. 6 66. 60 84.0 600 606 0 8. 80 9 8. 0 60 46 4 660 90 44 9 48 40 68 09 0 498 64 9 86 9 60 940 80 40 6 4 80 666 69 80 8 49 8 900 890 408 86 6 6 86 6 08 8 8 8 98 0 0 8 4 6 86 64 6 9 CONSULT ACTORY BC DWDI AN SIZE CLASS I CLASS II CLASS III CLASS IV IMPELLER IMPELLER WEIGHT WEIGHT MAX. WR MAX. WR RPM (kg) (kg-m ) RPM (kg) (kg-m ) 96 9. 0. 468.0 0. 904.8 0.6 8 4.9 0.9 94. 0. 8. 0.9 6 8 6.9 0.9 0.6 0.48 * Operating speeds above 4000 RPM are not recommended. Consult factory. MAX. RPM IMPELLER WEIGHT (kg) CONSULT ACTORY* WR (kg-m ) MAX. RPM IMPELLER WEIGHT (kg) CONSULT ACTORY* WR (kg-m ) 8 49 4. 0.6 6. 0. 04 6. 0.9 66 40.0 0.99 00 96.6 0.86 4.. 9 4..4 44..8 6 8.9.48 49..9 84 60.9. 088 4..8 4 60 4.. 068 9..9 6 4..4 808 98.6 4.6 0 9 6.6.8 80 8. 4.6 6 9..4 44. 00 8. 6. 64 94.. 040 6 9.9 90 9.9 0 9.6 49.4 8 8.9 08 4 4. 6 4 6. 8.0 6 0 4. 88 8. 40 90 68 4. 8 8 6.4 49 09.6 6 0. 44 8 4 8. 68 98 49. 4 89 48. 4 0 6. 490 48 9. 966 4. 0. 40 9 8.4 4 66 8 8.6 8 99.6 4 48 60 499 6 600 6 4 9 89 4 48 998 60 90 46 6 8 660 4 96 64 6 90 0 8 40 8 49 0 0 90 88 648 96 88 80 868 4 940 80 49 990 604 89 66 46 40 8 8 898 890 46 40 948 4 8 94 6 648 9 406 98 6 89 484 604 89 CONSULT ACTORY CONSULT ACTORY

MATERIAL SPECIICATIONS BC SWSI Class I HOUSING SHAT DIAMETER & BEARINGS BARE AN WEIGHT (kg) AN ARR & 9 ARR SIDES SCROLL SIZE SHAT BEARING SHAT BEARING (mm) (mm) ARR ARR ARR 9 DIA. TYPE DIA. TYPE B B 4 4 6 B B 6 6 B B 4 6 8 6 B B 8 8 9 8 0 B 0 B 96 00 8 B 8 B 9 4 8 B 8 B 6 6 8 4 8 B 8 B 4 0 4 B 8 B 6 90 69 00 0 B 4 B 08 84 4 0 0 B 4 B 400 9 6 0 B 0 B 49 4 48 40 B 0 B 609 0 69 44 6 B 0 B 69 490 0 B R 84 0 8 4 B 6 R 9 99 600 B R 40 49 660 90 R R 8 9 0 90 R 90 R 0 68 80 0 R 0 R 80 86 94 890 0 R 0 R 864 60 98 SR SR 4049 9 4 Bearing Types: B = Ball Bearing R = Unit Roller Bearings SR = Split Pillow Block Roller Bearings BC SWSI Class II HOUSING SHAT DIAMETER & BEARINGS BARE AN WEIGHT (kg) AN ARR & 9 ARR SIDES SCROLL SIZE SHAT BEARING SHAT BEARING (mm) (mm) ARR ARR ARR 9 DIA. TYPE DIA. TYPE B B 6 0 9 B B 64 60 6 0 B 0 B 9 8 6 0 B 0 B 9 96 9 8 8 B 8 B 9 00 8 B 8 B 40 46 8 B 8 B 80 9 89 4 4 B 4 B 69 0 4 B 4 B 6 00 0 B 0 B 0 B B 89 440 408 6 6 B 6 B 49 44 40 6 R 6 B 64 60 666 44 0 R 0 R 4 6 8 490 R 0 R 80 848 9 4 90 R R 9 8 600 90 R 90 R 4 4 660 0 R 0 R 9 9 00 0 0 R 0 R 8 40 80 SR SR 8 6 00 890 SR SR 4 98 enq SR enq SR 44 69 46 Bearing Types: B = Ball Bearing R = Unit Roller Bearings SR = Split Pillow Block Roller Bearings 4 TWIN CITY AN - CATALOGUE M00

MATERIAL SPECIICATIONS BC SWSI Class III HOUSING SHAT DIAMETER & BEARINGS BARE AN WEIGHT (kg) AN ARR & 9 ARR SIDES SCROLL SIZE SHAT BEARING SHAT BEARING (mm) (mm) ARR ARR ARR 9 DIA. TYPE DIA. TYPE 8 B 8 B 6 89 66 8 B 8 B 6 4 B 4 B 90 9 6 4 B 4 B 6 8 4 B 4 B 9 40 00 0 B 4 B 6 9 64 0 B 0 R 0 4 B 0 R 8 4 96 0 B 0 R 6 90 00 6 R R 4 468 4 0 0 R 6 R 6 46 6 0 R 6 R 60 68 66 40 R 0 R 8 80 80 44 90 R R 960 08 490 90 R R 6 6 8 4 0 R 90 R 9 4 6 600 SR 0 R 0 0 4 660 SR 0 R 40 69 0 SR SR 89 46 08 80 SR SR 898 60 04 890 enq SR enq SR 48 4 6 Bearing Types: B = Ball Bearing R = Unit Roller Bearings SR = Split Pillow Block Roller Bearings BC SWSI Class IV HOUSING SHAT DIAMETER & BEARINGS BARE AN WEIGHT (kg) AN ARR & 9 ARR SIDES SCROLL SIZE SHAT BEARING SHAT BEARING (mm) (mm) ARR ARR ARR 9 DIA. TYPE DIA. TYPE 4 B 4 B 80 9 84 4 B 4 B 9 96 4 B 4 B 40 6 0 B 4 R 84 8 0 B 4 R 99 8 00 R 0 R 9 4 R 0 R 6 4 8 4 6 R R 0 6 R R 89 408 00 0 R 6 R 490 0 0 6 6 R 0 R 669 0 0 6 6 6 90 R R 86 908 40 6 6 90 R R 64 9 44 6 6 0 R 90 R 96 490 6 6 0 R 90 R 84 6 4 6 6 SR 0 R 996 640 096 600 6 6 SR SR 4 4 0 660 6 6 SR SR 90 99 0 0 6 6 enq SR SR 9 49 8 80 6 6 enq SR enq SR 404 0 890 6 6 enq SR enq SR 48 4806 490 Bearing Types: B = Ball Bearing R = Unit Roller Bearings SR = Split Pillow Block Roller Bearings

MATERIAL SPECIICATIONS BC DWDI Class I & II HOUSING SHAT DIAMETER & BEARINGS BARE AN WEIGHT (kg) AN CLASS I CLASS II ARR. ARR. SIDES SCROLL SIZE SHAT DIAMETER BEARING SHAT DIAMETER BEARING (mm) (mm) CLASS I CLASS II CLASS I CLASS II @ BRG. @ IMP TYPE @ BRG. @ IMP TYPE 0 0 B 8 8 B 6 0 8 90 0 0 B 4 4 B 9 94 8 8 B 4 4 B 88 96 4 6 8 8 B 0 0 B 44 8 4 4 B 0 0 B 4 46 6 00 4 4 B B 6 0 0 0 B 6 6 B 0 66 9 4 B 6 6 B 0 0 B 0 0 R 90 0 8 4 00 6 6 B 0 R 40 448 9 8 0 6 6 B 0 90 R 46 08 600 660 6 0 0 B 0 90 R 6 66 99 89 40 0 R 0 90 R 68 84 999 99 44 0 90 R 0 R 9 0 4 6 490 0 90 R 90 0 R 0 6 4 0 R 90 R 9 4 4 9 600 90 R 0 R 886 0 660 90 R 0 R 409 60 0 0 R 0 enq R 00 80 0 enq R enq SR 44 90 890 enq R enq SR 46 40 98 enq SR enq enq SR 04 6 Bearing Types: B = Ball Bearing R = Unit Roller Bearings SR = Split Pillow Block Roller Bearings BC DWDI Class III & IV AN SIZE HOUSING (mm) BARE AN WEIGHT SHAT DIAMETER & BEARINGS (kg) CLASS III CLASS IV ARR. SHAT DIAMETER BEARING CLASS III CLASS IV TYPE TYPE CLASS III CLASS IV SHAT DIAMETER BEARING SIDES SCROLL SIDES SCROLL @ BRG. @ IMP @ BRG. @ IMP 6 CONSULT ACTORY CONSULT ACTORY CONSULT ACTORY CONSULT ACTORY CONSULT ACTORY 8 R 6 6 R 00 6 6 R SR 8 6 6 R 6 90 SR 64 40 4 6 R 0 0 SR 40 446 0 0 90 R 0 SR 49 4 00 0 90 R SR 60 44 0 6 6 90 R 90 SR 9 8 6 6 6 0 R 90 SR 99 40 6 6 90 0 R 0 enq SR 6 90 44 6 6 90 R 0 enq SR 44 604 490 6 6 0 R enq SR 8 4 4 6 6 0 enq R enq SR 000 600 6 6 enq SR enq SR 8 6 660 6 6 enq SR enq enq SR 68 409 0 6 6 enq SR enq enq SR 44 44 80 6 6 SR SR 8 890 6 6 SR SR 68 0 98 6 6 Bearing Types: B = Ball Bearing R = Unit Roller Bearings SR = Split Pillow Block Roller Bearings SPECIICATIONS SUBJECT TO CHANGE WITHOUT NOTICE. 6 TWIN CITY AN - CATALOGUE M00

BC-SW 00 RPM 80 RPM 00 RPM 000 RPM.kW. 0. 00 00 960 RPM 40 RPM LwA 8 LwA.kW.kW 0.kW 0.kW 0.kW 0.kW 0. 0 0% Pk. Eff. 0.8kW 0. 80 % Eff. 0. 0 0. 0. 0.8 -low (m³ / sec) 0 0 0 0 0 00 00 - an Velocity Pressure (Pa) an Efficiency Grade = EG 80 0. 0.. - low (CM) (in Thousands). Performance certified is for Installation Type B & D: ree or ducted inlet, ducted outlet.. Power rating (kw) does not include transmission losses.. Performance ratings do not include the effects of appurtenances (accessories). 4. The sound power level ratings shown are in decibels, referred to E- watts calculated per AMCA Standard 0.. Values shown are for inlet LwiA sound power levels for Installation Type B: ree inlet, ducted outlet.. The A-weighted sound ratings shown have been calculated per AMCA Standard 0.

,000 BC-SW 00 RPM 80 RPM 9 LwA 00 RPM. 00 00 40 RPM 000 RPM 8 LwA kw.kw.kw.kw 0.kW 0.kW 0. 0. 960 RPM 0% Pk. Eff. LwA 0.kW 0.kW 0 0.8kW 0. 80 % Eff. 0 0. 0. 0.8 -low (m³ / sec) 0 0 0 0 0 00 00 00 - an Velocity Pressure (Pa) 0. 0.. - low (CM) (in Thousands) an Efficiency Grade = EG 80. Performance certified is for Installation Type B & D: ree or ducted inlet, ducted outlet.. Power rating (kw) does not include transmission losses.. Performance ratings do not include the effects of appurtenances (accessories). 4. The sound power level ratings shown are in decibels, referred to E- watts calculated per AMCA Standard 0.. Values shown are for inlet LwiA sound power levels for Installation Type B: ree inlet, ducted outlet.. The A-weighted sound ratings shown have been calculated per AMCA Standard 0. 8 TWIN CITY AN - CATALOGUE M00

,000 BC-SW 00 RPM 00 RPM 80 RPM 0 LwA. 0. 00 00 960 RPM 40 RPM 000 RPM 8 LwA 9 LwA.kW 4kW kw.kw.kw.kw 0.kW 0.kW LwA 0.kW 0. 0 RPM 0.kW 0. 0 80 0% Pk. Eff. 0 LwA 0.8kW 0. 0 % Eff. 0. 0. 0.8 -low (m³ / sec) 0 0 0 0 0 00 00 - an Velocity Pressure (Pa) an Efficiency Grade = EG 0.. - low (CM) (in Thousands). Performance certified is for Installation Type B & D: ree or ducted inlet, ducted outlet.. Power rating (kw) does not include transmission losses.. Performance ratings do not include the effects of appurtenances (accessories). 4. The sound power level ratings shown are in decibels, referred to E- watts calculated per AMCA Standard 0.. Values shown are for inlet LwiA sound power levels for Installation Type B: ree inlet, ducted outlet.. The A-weighted sound ratings shown have been calculated per AMCA Standard 0. 9

,000 BC-SW 6 00 RPM 80 RPM LwA 00 RPM. 00 00 960 RPM 40 RPM 000 RPM 8 LwA 9 LwA 0 LwA 4kW kw.kw.kw.kw.kw.kw 0.kW 0. 0.kW 0 RPM LwA 0. 0 0% Pk. Eff. 0.kW 0.kW 0. 80 % Eff. 0.8kW 0 0.4 0.8 4 -low (m³ / sec) 0 0 0 0 0 00 00 - an Velocity Pressure (Pa) an Efficiency Grade = EG. - low (CM) (in Thousands). Performance certified is for Installation Type B & D: ree or ducted inlet, ducted outlet.. Power rating (kw) does not include transmission losses.. Performance ratings do not include the effects of appurtenances (accessories). 4. The sound power level ratings shown are in decibels, referred to E- watts calculated per AMCA Standard 0.. Values shown are for inlet LwiA sound power levels for Installation Type B: ree inlet, ducted outlet.. The A-weighted sound ratings shown have been calculated per AMCA Standard 0. 0 TWIN CITY AN - CATALOGUE M00

4,000 BC-SW 8 00 RPM 80 RPM,000 00 RPM 0 LwA 9 LwA kw 000 RPM kw. 400 960 RPM 40 RPM 8 LwA.kW 4kW kw.kw.kw.kw LwA.kW 00 0 LwA 0.kW 0. 0. 0 RPM 6% Pk. Eff. 6 LwA 0.kW 0.kW 0. 0 80 0. 0.8 6% Eff. 0.kW 0.8kW -low (m³ / sec) 0 0 0 0 0 00 00 00 - an Velocity Pressure (Pa). - low (CM) (in Thousands) an Efficiency Grade = EG 80. Performance certified is for Installation Type B & D: ree or ducted inlet, ducted outlet.. Power rating (kw) does not include transmission losses.. Performance ratings do not include the effects of appurtenances (accessories). 4. The sound power level ratings shown are in decibels, referred to E- watts calculated per AMCA Standard 0.. Values shown are for inlet LwiA sound power levels for Installation Type B: ree inlet, ducted outlet.. The A-weighted sound ratings shown have been calculated per AMCA Standard 0.

4,000 BC-SW 00 80 RPM 00 RPM,000 0 LwA 000 RPM 9 LwA. 600 400 960 RPM 40 RPM LwA 8 LwA kw.kw.kw 4kW.kW.kW kw.kw 0. 0 00RPM 6% Pk. Eff. 0 LwA 0.kW 0.kW 0. 0 6% Eff. 0.kW 0. 80 0.kW 0.8 4 6 -low (m³ / sec) 0 0 0 0 0 00 00 - an Velocity Pressure (Pa). - low (CM) (in Thousands) an Efficiency Grade = EG 80. Performance certified is for Installation Type B & D: ree or ducted inlet, ducted outlet.. Power rating (kw) does not include transmission losses.. Performance ratings do not include the effects of appurtenances (accessories). 4. The sound power level ratings shown are in decibels, referred to E- watts calculated per AMCA Standard 0.. Values shown are for inlet LwiA sound power levels for Installation Type B: ree inlet, ducted outlet.. The A-weighted sound ratings shown have been calculated per AMCA Standard 0. TWIN CITY AN - CATALOGUE M00

4,000 BC-SW 80 RPM 00 RPM LwA,000 000 RPM 0 LwA kw 9 LwA 8.kW. 600 400 0 RPM 960 RPM 40 RPM LwA 8 LwA 4kW kw.kw.kw kw kw.kw.kw 0. 00 0 LwA.kW 0.kW 0. 00 RPM 6 LwA 0.kW 0. 0 80 60 6% Pk. Eff. 6% Eff. 0.kW 0.kW 0.8kW 0.8 4 6 8 -low (m³ / sec) 0 0 0 0 0 00 00 00 - an Velocity Pressure (Pa). - low (CM) (in Thousands) an Efficiency Grade = EG 80. Performance certified is for Installation Type B & D: ree or ducted inlet, ducted outlet.. Power rating (kw) does not include transmission losses.. Performance ratings do not include the effects of appurtenances (accessories). 4. The sound power level ratings shown are in decibels, referred to E- watts calculated per AMCA Standard 0.. Values shown are for inlet LwiA sound power levels for Installation Type B: ree inlet, ducted outlet.. The A-weighted sound ratings shown have been calculated per AMCA Standard 0.

4,000 BC-SW 4 00 RPM LwA 000 RPM,000 0 LwA. 600 400 00 0 RPM 960 RPM 0 LwA LwA 40 RPM 8 LwA 9 LwA kw.kw.kw 4kW kw.kw.kw kw 8.kW kw 0..kW 0. 00 RPM 0 6% Pk. Eff. 6 LwA 0.kW 0.kW 0. 80 6% Eff. 0.kW 60 0.kW 4 6 8 -low (m³ / sec) 0 0 0 0 0 00 00 00 - an Velocity Pressure (Pa) an Efficiency Grade = EG 80 0 - low (CM) (in Thousands). Performance certified is for Installation Type B & D: ree or ducted inlet, ducted outlet.. Power rating (kw) does not include transmission losses.. Performance ratings do not include the effects of appurtenances (accessories). 4. The sound power level ratings shown are in decibels, referred to E- watts calculated per AMCA Standard 0.. Values shown are for inlet LwiA sound power levels for Installation Type B: ree inlet, ducted outlet.. The A-weighted sound ratings shown have been calculated per AMCA Standard 0. 4 TWIN CITY AN - CATALOGUE M00

0,000 BC-SW 0 00 RPM,000 000 RPM LwA 0 LwA 40 RPM 4kW kw. 00 0 RPM 960 RPM 8 LwA 9 LwA 0kW kw 8.kW kw kw.kw.kw 4kW 00 kw LwA.kW 0. 0. 00 RPM 6% Eff. 9% Pk. Eff. 0 LwA.kW.kW 0.kW 0 6% Eff. 0.kW 80 8 0 -low (m³ / sec) 0 0 0 0 0 00 00 00 00 00 - an Velocity Pressure (Pa) an Efficiency Grade = EG 8 0 0 - low (CM) (in Thousands). Performance certified is for Installation Type B & D: ree or ducted inlet, ducted outlet.. Power rating (kw) does not include transmission losses.. Performance ratings do not include the effects of appurtenances (accessories). 4. The sound power level ratings shown are in decibels, referred to E- watts calculated per AMCA Standard 0.. Values shown are for inlet LwiA sound power levels for Installation Type B: ree inlet, ducted outlet.. The A-weighted sound ratings shown have been calculated per AMCA Standard 0.

4,000 BC-SW 00 000 RPM LwA,000 40 RPM 0 LwA. 600 400 0 RPM 960 RPM 8 LwA 9 LwA kw 0kW kw 8.kW kw kw.kw.kw 4kW 0. 00 00 RPM 6% Eff. 9% Pk. Eff. LwA.kW.kW kw 0. 6% Eff..kW 0 0.kW 4 6 8 0 -low (m³ / sec) 0 0 0 0 0 00 00 00 00 00 - an Velocity Pressure (Pa) an Efficiency Grade = EG 8 0 0 - low (CM) (in Thousands). Performance certified is for Installation Type B & D: ree or ducted inlet, ducted outlet.. Power rating (kw) does not include transmission losses.. Performance ratings do not include the effects of appurtenances (accessories). 4. The sound power level ratings shown are in decibels, referred to E- watts calculated per AMCA Standard 0.. Values shown are for inlet LwiA sound power levels for Installation Type B: ree inlet, ducted outlet.. The A-weighted sound ratings shown have been calculated per AMCA Standard 0. 6 TWIN CITY AN - CATALOGUE M00

0 4,000 BC-SW 0 000 RPM,000 40 RPM LwA 0 LwA kw. 600 400 0 RPM 960 RPM 8 LwA 9 LwA kw 8.kW kw kw.kw.kw 4kW kw 0kW 0. 00 RPM 00 6% Eff. 9% Pk. Eff. LwA 4kW kw.kw 6% Eff..kW 0..kW 0 4 6 8 0 -low (m³ / sec) 0 0 0 0 0 00 00 00 00 - an Velocity Pressure (Pa) an Efficiency Grade = EG 80 0 0 - low (CM) (in Thousands). Performance certified is for Installation Type B & D: ree or ducted inlet, ducted outlet.. Power rating (kw) does not include transmission losses.. Performance ratings do not include the effects of appurtenances (accessories). 4. The sound power level ratings shown are in decibels, referred to E- watts calculated per AMCA Standard 0.. Values shown are for inlet LwiA sound power levels for Installation Type B: ree inlet, ducted outlet.. The A-weighted sound ratings shown have been calculated per AMCA Standard 0.

4,000 BC-SW 6 40 RPM,000 0 LwA 960 RPM 9 LwA kw. 0. 600 400 00 0 RPM 00 RPM.kW.kW 4kW kw.kw 0kW kw 8.kW kw kw 0 80 60 00 RPM 60 LwA 6 LwA LwA 0 LwA 8 LwA 0. 0. 8% Pk. Eff. 68% Eff..kW.kW 0.kW 0.kW 4 6 8 0 -low (m³ / sec) 0 0 0 0 0 00 00 - an Velocity Pressure (Pa) an Efficiency Grade = EG 8 4 0 0 40 - low (CM) (in Thousands). Performance certified is for Installation Type B & D: ree or ducted inlet, ducted outlet.. Power rating (kw) does not include transmission losses.. Performance ratings do not include the effects of appurtenances (accessories). 4. The sound power level ratings shown are in decibels, referred to E- watts calculated per AMCA Standard 0.. Values shown are for inlet LwiA sound power levels for Installation Type B: ree inlet, ducted outlet.. The A-weighted sound ratings shown have been calculated per AMCA Standard 0. 8 TWIN CITY AN - CATALOGUE M00

4,000 BC-SW 40 40 RPM LwA,000 0 LwA 960 RPM 9 LwA 4kW kw. 600 400 00 RPM 8 LwA LwA 0 LwA kw 0 RPM 0kW kw kw.kw.kw 4kW kw 8.kW 00 kw 0. 0. 00 RPM 8% Pk. Eff. 6 LwA.kW.kW 0. 0 80 68% Eff..kW 0.kW 60 4 6 8 0 -low (m³ / sec) 0 0 0 0 0 00 00 00 00 - an Velocity Pressure (Pa) an Efficiency Grade = EG 8 0 0 40 0 - low (CM) (in Thousands). Performance certified is for Installation Type B & D: ree or ducted inlet, ducted outlet.. Power rating (kw) does not include transmission losses.. Performance ratings do not include the effects of appurtenances (accessories). 4. The sound power level ratings shown are in decibels, referred to E- watts calculated per AMCA Standard 0.. Values shown are for inlet LwiA sound power levels for Installation Type B: ree inlet, ducted outlet.. The A-weighted sound ratings shown have been calculated per AMCA Standard 0. 9

0 4,000 BC-SW 44 40 RPM LwA,000 960 RPM 0 LwA 90kW kw kw. 600 400 00 RPM 0 RPM LwA 9 LwA 8 LwA kw 8.kW kw kw.kw kw 4kW kw 0kW 0 LwA.kW 0. 00 00 RPM 8% Pk. Eff. 6 LwA 4kW kw.kw 0. 0 68% Eff..kW 80.kW 4 6 8 0 40 -low (m³ / sec) 0 0 0 0 0 00 00 00 00 - an Velocity Pressure (Pa) an Efficiency Grade = EG 8 0 0 40 0 0 - low (CM) (in Thousands). Performance certified is for Installation Type B & D: ree or ducted inlet, ducted outlet.. Power rating (kw) does not include transmission losses.. Performance ratings do not include the effects of appurtenances (accessories). 4. The sound power level ratings shown are in decibels, referred to E- watts calculated per AMCA Standard 0.. Values shown are for inlet LwiA sound power levels for Installation Type B: ree inlet, ducted outlet.. The A-weighted sound ratings shown have been calculated per AMCA Standard 0. 0 TWIN CITY AN - CATALOGUE M00

BC-SW 490 960 RPM,000 0 LwA 0 RPM 9 LwA kw. 600 400 00 RPM LwA 8 LwA 4kW kw 0kW kw 8.kW kw kw.kw 0. 00 00 RPM 8% Pk. Eff. 0 LwA 4kW.kW 0. 68% Eff..kW kw 0 4 6 8 0 -low (m³ / sec) 0 0 0 0 0 00 00 - an Velocity Pressure (Pa) an Efficiency Grade = EG 8 0 0 40 0 - low (CM) (in Thousands). Performance certified is for Installation Type B & D: ree or ducted inlet, ducted outlet.. Power rating (kw) does not include transmission losses.. Performance ratings do not include the effects of appurtenances (accessories). 4. The sound power level ratings shown are in decibels, referred to E- watts calculated per AMCA Standard 0.. Values shown are for inlet LwiA sound power levels for Installation Type B: ree inlet, ducted outlet.. The A-weighted sound ratings shown have been calculated per AMCA Standard 0.

BC-SW 4 960 RPM,000 0 RPM 0 LwA 90kW 9 LwA kw kw. 0. 600 400 00 00 RPM 00 RPM 0 LwA LwA 8 LwA kw.kw.kw 4kW 4kW kw 0kW kw 8.kW kw 0. 0. 00 RPM 0 80 60 8% Pk. Eff. 60 LwA 6 LwA 68% Eff. kw.kw.kw.kw 4 6 8 0 40 -low (m³ / sec) 0 0 0 0 0 00 00 - an Velocity Pressure (Pa) an Efficiency Grade = EG 8 0 0 40 0 0 - low (CM) (in Thousands). Performance certified is for Installation Type B & D: ree or ducted inlet, ducted outlet.. Power rating (kw) does not include transmission losses.. Performance ratings do not include the effects of appurtenances (accessories). 4. The sound power level ratings shown are in decibels, referred to E- watts calculated per AMCA Standard 0.. Values shown are for inlet LwiA sound power levels for Installation Type B: ree inlet, ducted outlet.. The A-weighted sound ratings shown have been calculated per AMCA Standard 0. TWIN CITY AN - CATALOGUE M00

4,000 BC-SW 600 960 RPM LwA,000 0 RPM 0 LwA kw kw. 600 400 00 RPM 00 RPM LwA 8 LwA 9 LwA 4kW kw 0kW kw 8.kW kw kw 90kW kw kw 00 0 LwA.kW 0. 0. 00 RPM 8% Pk. Eff. 6 LwA 4kW kw.kw 0. 0 80 68% Eff..kW.kW 60 6 8 0 40 60 -low (m³ / sec) 0 0 0 0 0 00 00 00 - an Velocity Pressure (Pa) an Efficiency Grade = EG 8 0 0 40 0 0 0 - low (CM) (in Thousands). Performance certified is for Installation Type B & D: ree or ducted inlet, ducted outlet.. Power rating (kw) does not include transmission losses.. Performance ratings do not include the effects of appurtenances (accessories). 4. The sound power level ratings shown are in decibels, referred to E- watts calculated per AMCA Standard 0.. Values shown are for inlet LwiA sound power levels for Installation Type B: ree inlet, ducted outlet.. The A-weighted sound ratings shown have been calculated per AMCA Standard 0.

0,000 BC-SW 660 960 RPM LwA,000 0 RPM LwA 0 LwA 60kW. 00 00 00 RPM 00 RPM LwA 8 LwA 9 LwA kw 4kW kw 0kW kw 8.kW kw kw kw 90kW kw 0 LwA kw 0. 0. 00 RPM 8% Pk. Eff. 4kW.kW.kW 0 68% Eff. kw 80 0 40 0 -low (m³ / sec) 0 0 0 0 0 00 00 00 - an Velocity Pressure (Pa) an Efficiency Grade = EG 8 0 0 40 0 0 0 - low (CM) (in Thousands). Performance certified is for Installation Type B & D: ree or ducted inlet, ducted outlet.. Power rating (kw) does not include transmission losses.. Performance ratings do not include the effects of appurtenances (accessories). 4. The sound power level ratings shown are in decibels, referred to E- watts calculated per AMCA Standard 0.. Values shown are for inlet LwiA sound power levels for Installation Type B: ree inlet, ducted outlet.. The A-weighted sound ratings shown have been calculated per AMCA Standard 0. 4 TWIN CITY AN - CATALOGUE M00

BC-SW 0 0 RPM LwA,000 0 LwA 00 RPM 60kW 600 400 00 00 RPM 00 RPM 6 LwA 9 LwA kw kw. 0 LwA LwA 8 LwA kw 0kW kw 8.kW kw kw 90kW kw kw 4kW 0..kW 0. RPM 0 8% Pk. Eff. kw 4kW.kW 0. 80 60 68% Eff..kW 8 0 40 60 80 -low (m³ / sec) 0 0 0 0 0 00 00 - an Velocity Pressure (Pa) an Efficiency Grade = EG 8 0 0 40 0 0 0 - low (CM) (in Thousands). Performance certified is for Installation Type B & D: ree or ducted inlet, ducted outlet.. Power rating (kw) does not include transmission losses.. Performance ratings do not include the effects of appurtenances (accessories). 4. The sound power level ratings shown are in decibels, referred to E- watts calculated per AMCA Standard 0.. Values shown are for inlet LwiA sound power levels for Installation Type B: ree inlet, ducted outlet.. The A-weighted sound ratings shown have been calculated per AMCA Standard 0.

4,000 BC-SW 80 0 RPM LwA,000 00 RPM 0 LwA. 0. 0. 600 400 00 RPM 00 RPM 8% Pk. Eff. 0 LwA 6 LwA 00 RPM LwA 8 LwA 9 LwA 0kW kw 8.kW kw kw.kw.kw 60kW kw kw 90kW kw kw 4kW kw 0. 0 80 68% Eff. kw 4kW 60 0 40 60 80 0 -low (m³ / sec) 0 0 0 0 0 00 00 - an Velocity Pressure (Pa) an Efficiency Grade = EG 8 0 40 0 0 0 00 - low (CM) (in Thousands). Performance certified is for Installation Type B & D: ree or ducted inlet, ducted outlet.. Power rating (kw) does not include transmission losses.. Performance ratings do not include the effects of appurtenances (accessories). 4. The sound power level ratings shown are in decibels, referred to E- watts calculated per AMCA Standard 0.. Values shown are for inlet LwiA sound power levels for Installation Type B: ree inlet, ducted outlet.. The A-weighted sound ratings shown have been calculated per AMCA Standard 0. 6 TWIN CITY AN - CATALOGUE M00

0 4,000 BC-SW 890 0 RPM LwA,000 00 RPM 0 LwA LwA. 600 400 00 RPM 00 RPM 8 LwA 9 LwA 90kW kw kw 4kW kw 0kW 60kW kw kw LwA kw 0. 0. 00 0 RPM 8% Pk. Eff. 6 LwA 0 LwA 68% Eff. 8.kW kw kw.kw.kw 80 0 40 60 80 0 00 -low (m³ / sec) 0 0 0 0 0 00 00 00 00 00 - an Velocity Pressure (Pa) an Efficiency Grade = EG 8 0 40 0 0 0 00 00 - low (CM) (in Thousands). Performance certified is for Installation Type B & D: ree or ducted inlet, ducted outlet.. Power rating (kw) does not include transmission losses.. Performance ratings do not include the effects of appurtenances (accessories). 4. The sound power level ratings shown are in decibels, referred to E- watts calculated per AMCA Standard 0.. Values shown are for inlet LwiA sound power levels for Installation Type B: ree inlet, ducted outlet.. The A-weighted sound ratings shown have been calculated per AMCA Standard 0.

BC-SW 98 00 RPM,000 0 LwA. 600 400 00 RPM 00 RPM 60kW 8 LwA 9 LwA kw kw 90kW kw kw 4kW kw LwA 0kW 0. 00 RPM 8% Pk. Eff. 0 LwA kw 8.kW kw 0. 68% Eff..kW kw 0 0 40 60 80 0 00 -low (m³ / sec) 0 0 0 0 0 00 00 00 00 - an Velocity Pressure (Pa) an Efficiency Grade = EG 8 0 40 0 0 0 00 00 - low (CM) (in Thousands). Performance certified is for Installation Type B & D: ree or ducted inlet, ducted outlet.. Power rating (kw) does not include transmission losses.. Performance ratings do not include the effects of appurtenances (accessories). 4. The sound power level ratings shown are in decibels, referred to E- watts calculated per AMCA Standard 0.. Values shown are for inlet LwiA sound power levels for Installation Type B: ree inlet, ducted outlet.. The A-weighted sound ratings shown have been calculated per AMCA Standard 0. 8 TWIN CITY AN - CATALOGUE M00

,000 BC-DW 00 RPM 80 RPM 00 RPM 9 LwA 4kW. 0. 00 00 40 RPM 000 RPM LwA 8 LwA kw.kw.kw.kw 0.kW 0.kW 0. 960 RPM 0 6% Eff. 0% Pk. Eff. 0 LwA 0.kW 0.kW 0. 80 8% Eff. 0.8kW 0 0. 0. 0.8 -low (m³ / sec) 0 0 0 0 0 00 - an Velocity Pressure (Pa) an Efficiency Grade = EG 80 0.. - low (CM) (in Thousands). Performance certified is for Installation Type B & D: ree or ducted inlet, ducted outlet.. Power rating (kw) does not include transmission losses.. Performance ratings do not include the effects of appurtenances (accessories). 4. The sound power level ratings shown are in decibels, referred to E- watts calculated per AMCA Standard 0.. Values shown are for inlet LwiA sound power levels for Installation Type B: ree inlet, ducted outlet.. The A-weighted sound ratings shown have been calculated per AMCA Standard 0. 9

BC-DW,000 00 RPM 80 RPM 0 LwA 00 RPM 9 LwA. 600 400 40 RPM 000 RPM 8 LwA 4kW kw.kw.kw.kw.kw 0. 0. 00 960 RPM 6% Eff. 0% Pk. Eff. 0 LwA LwA 0.kW 0.kW 0.kW 0. 0 80 8% Eff. 0.kW 0.8kW 60 0.4 0.6 0.8 4 -low (m³ / sec) 0 0 0 0 0 00 00 - an Velocity Pressure (Pa) an Efficiency Grade = EG 80. - low (CM) (in Thousands). Performance certified is for Installation Type B & D: ree or ducted inlet, ducted outlet.. Power rating (kw) does not include transmission losses.. Performance ratings do not include the effects of appurtenances (accessories). 4. The sound power level ratings shown are in decibels, referred to E- watts calculated per AMCA Standard 0.. Values shown are for inlet LwiA sound power levels for Installation Type B: ree inlet, ducted outlet.. The A-weighted sound ratings shown have been calculated per AMCA Standard 0. 40 TWIN CITY AN - CATALOGUE M00

BC-DW 00 RPM,000 80 RPM LwA 00 RPM 0 LwA. 0. 600 400 00 960 RPM 40 RPM 000 RPM LwA 8 LwA 9 LwA 4kW kw.kw.kw.kw kw.kw.kw 0.kW 0. 0. 0 RPM 0 80 6% Eff. 6% Pk. Eff. 6 LwA 0 LwA 0.kW 0.kW 0.kW 0. 60 % Eff. 0.8kW 40 0.6 0.8 4 6 -low (m³ / sec) 0 0 0 0 0 00 00 - an Velocity Pressure (Pa). - low (CM) (in Thousands) an Efficiency Grade = EG. Performance certified is for Installation Type B & D: ree or ducted inlet, ducted outlet.. Power rating (kw) does not include transmission losses.. Performance ratings do not include the effects of appurtenances (accessories). 4. The sound power level ratings shown are in decibels, referred to E- watts calculated per AMCA Standard 0.. Values shown are for inlet LwiA sound power levels for Installation Type B: ree inlet, ducted outlet.. The A-weighted sound ratings shown have been calculated per AMCA Standard 0. 4

4,000 BC-DW 6 00 RPM,000 80 RPM LwA 00 RPM. 600 400 00 960 RPM 40 RPM LwA 000 RPM 8 LwA 9 LwA 0 LwA kw.kw.kw 4kW kw.kw.kw 8.kW kw 0..kW 0. 0 RPM 0 6% Eff. 6% Pk. Eff. 0 LwA 0.kW 0.kW 0. 80 60 % Eff. 0.kW 0.kW 0.6 0.8 4 6 8 -low (m³ / sec) 0 0 0 0 0 00 00 00 - an Velocity Pressure (Pa) an Efficiency Grade = EG. - low (CM) (in Thousands). Performance certified is for Installation Type B & D: ree or ducted inlet, ducted outlet.. Power rating (kw) does not include transmission losses.. Performance ratings do not include the effects of appurtenances (accessories). 4. The sound power level ratings shown are in decibels, referred to E- watts calculated per AMCA Standard 0.. Values shown are for inlet LwiA sound power levels for Installation Type B: ree inlet, ducted outlet.. The A-weighted sound ratings shown have been calculated per AMCA Standard 0. 4 TWIN CITY AN - CATALOGUE M00

0,000 BC-DW 8 00 RPM LwA,000 80 RPM 00 RPM LwA LwA. 00 00 960 RPM 000 RPM 40 RPM 8 LwA 9 LwA 0 LwA 4kW kw 0kW kw 8.kW kw kw.kw.kw.kw LwA.kW 0. 0. 0 RPM % Pk. Eff. 0.kW.kW 0. 0 80 60% Eff. 0.kW 0.kW 4 6 8 -low (m³ / sec) 0 0 0 0 0 00 00 00 - an Velocity Pressure (Pa) an Efficiency Grade = EG. 0 - low (CM) (in Thousands). Performance certified is for Installation Type B & D: ree or ducted inlet, ducted outlet.. Power rating (kw) does not include transmission losses.. Performance ratings do not include the effects of appurtenances (accessories). 4. The sound power level ratings shown are in decibels, referred to E- watts calculated per AMCA Standard 0.. Values shown are for inlet LwiA sound power levels for Installation Type B: ree inlet, ducted outlet.. The A-weighted sound ratings shown have been calculated per AMCA Standard 0. 4

4,000 BC-DW 00 80 RPM 00 RPM LwA,000 LwA 000 RPM 0 LwA. 600 400 960 RPM 8 LwA 40 RPM 9 LwA kw 8.kW kw kw.kw.kw 4kW kw 0. 00 0 RPM % Pk. Eff. LwA.kW.kW.kW 0. 0 60% Eff. 0.kW 0.kW 80 4 6 8 0 -low (m³ / sec) 0 0 0 0 0 00 00 00 00 00 - an Velocity Pressure (Pa) an Efficiency Grade = EG 0 0 - low (CM) (in Thousands). Performance certified is for Installation Type B & D: ree or ducted inlet, ducted outlet.. Power rating (kw) does not include transmission losses.. Performance ratings do not include the effects of appurtenances (accessories). 4. The sound power level ratings shown are in decibels, referred to E- watts calculated per AMCA Standard 0.. Values shown are for inlet LwiA sound power levels for Installation Type B: ree inlet, ducted outlet.. The A-weighted sound ratings shown have been calculated per AMCA Standard 0. 44 TWIN CITY AN - CATALOGUE M00

0,000 BC-DW 80 RPM LwA,000 00 RPM LwA 000 RPM LwA 4kW. 00 00 00 40 RPM 960 RPM.kW.kW 4kW 0 RPM kw 8 LwA 0 LwA 9 LwA kw 0kW kw 8.kW kw kw LwA.kW 0..kW 0. 0 00 RPM % Pk. Eff. 0 LwA.kW 0.kW 0.kW 0. 0 60% Eff. 0.kW 0 4 6 8 0 -low (m³ / sec) 0 0 0 0 0 00 00 00 00 00 - an Velocity Pressure (Pa) an Efficiency Grade = EG 0 0 - low (CM) (in Thousands). Performance certified is for Installation Type B & D: ree or ducted inlet, ducted outlet.. Power rating (kw) does not include transmission losses.. Performance ratings do not include the effects of appurtenances (accessories). 4. The sound power level ratings shown are in decibels, referred to E- watts calculated per AMCA Standard 0.. Values shown are for inlet LwiA sound power levels for Installation Type B: ree inlet, ducted outlet.. The A-weighted sound ratings shown have been calculated per AMCA Standard 0. 4

BC-DW 4 00 RPM,000 000 RPM LwA LwA kw 40 RPM 4kW kw. 00 00 00 0 RPM 960 RPM 8 LwA 9 LwA 0 LwA 0kW kw 8.kW kw kw.kw.kw 4kW kw 0. 0. 0. 0 0 00 RPM % Pk. Eff. LwA 60% Eff..kW.kW.kW 0.kW 0.kW 0 4 6 8 0 -low (m³ / sec) 0 0 0 0 0 00 00 00 00 - an Velocity Pressure (Pa) an Efficiency Grade = EG 0 0 - low (CM) (in Thousands). Performance certified is for Installation Type B & D: ree or ducted inlet, ducted outlet.. Power rating (kw) does not include transmission losses.. Performance ratings do not include the effects of appurtenances (accessories). 4. The sound power level ratings shown are in decibels, referred to E- watts calculated per AMCA Standard 0.. Values shown are for inlet LwiA sound power levels for Installation Type B: ree inlet, ducted outlet.. The A-weighted sound ratings shown have been calculated per AMCA Standard 0. 46 TWIN CITY AN - CATALOGUE M00

0,000 BC-DW 0 00 RPM LwA,000 000 RPM LwA 90kW 40 RPM 0 LwA kw kw. 00 00 00 0 RPM 960 RPM 8 LwA 9 LwA kw 8.kW kw kw.kw.kw 4kW kw 0kW 4kW 0. 0. 00 RPM 6% Pk. Eff. LwA kw.kw.kw 0 64% Eff..kW 0. 0.kW 0 4 6 8 0 -low (m³ / sec) 0 0 0 0 0 00 00 00 00 00 - an Velocity Pressure (Pa) an Efficiency Grade = EG 80 0 0 0 - low (CM) (in Thousands). Performance certified is for Installation Type B & D: ree or ducted inlet, ducted outlet.. Power rating (kw) does not include transmission losses.. Performance ratings do not include the effects of appurtenances (accessories). 4. The sound power level ratings shown are in decibels, referred to E- watts calculated per AMCA Standard 0.. Values shown are for inlet LwiA sound power levels for Installation Type B: ree inlet, ducted outlet.. The A-weighted sound ratings shown have been calculated per AMCA Standard 0. 4

BC-DW 00 000 RPM,000 LwA 40 RPM 0 LwA kw. 00 00 0 RPM 960 RPM 8 LwA 9 LwA kw 8.kW kw kw.kw kw 4kW kw 0kW 00 0. 00 RPM 6% Pk. Eff. LwA kw 4kW.kW 0. 64% Eff..kW.kW 0 0 -low (m³ / sec) 0 0 0 0 0 00 00 00 00 - an Velocity Pressure (Pa) an Efficiency Grade = EG 80 0 0 40 0 - low (CM) (in Thousands). Performance certified is for Installation Type B & D: ree or ducted inlet, ducted outlet.. Power rating (kw) does not include transmission losses.. Performance ratings do not include the effects of appurtenances (accessories). 4. The sound power level ratings shown are in decibels, referred to E- watts calculated per AMCA Standard 0.. Values shown are for inlet LwiA sound power levels for Installation Type B: ree inlet, ducted outlet.. The A-weighted sound ratings shown have been calculated per AMCA Standard 0. 48 TWIN CITY AN - CATALOGUE M00

0,000 BC-DW 0 000 RPM LwA 40 RPM LwA,000 kw 90kW. 00 0 RPM 960 RPM 8 LwA 9 LwA 0 LwA kw 4kW kw 0kW kw 8.kW kw kw kw 00 RPM.kW 00 6% Pk. Eff. 4kW.kW 0. 64% Eff. kw 0..kW 0 4 6 8 0 40 -low (m³ / sec) 0 0 0 0 0 00 00 00 00 - an Velocity Pressure (Pa) an Efficiency Grade = EG 80 0 0 40 0 0 - low (CM) (in Thousands). Performance certified is for Installation Type B & D: ree or ducted inlet, ducted outlet.. Power rating (kw) does not include transmission losses.. Performance ratings do not include the effects of appurtenances (accessories). 4. The sound power level ratings shown are in decibels, referred to E- watts calculated per AMCA Standard 0.. Values shown are for inlet LwiA sound power levels for Installation Type B: ree inlet, ducted outlet.. The A-weighted sound ratings shown have been calculated per AMCA Standard 0. 49

BC-DW 6 40 RPM,000 LwA 960 RPM kw 0 LwA kw. 600 400 00 00 RPM 0 RPM 8 LwA 9 LwA 0kW kw 8.kW kw kw.kw.kw 4kW kw 0. LwA 4kW 0. 0 00 RPM 9% Pk. Eff. 0 LwA kw.kw.kw 0. 80 66% Eff..kW 60 4 6 8 0 40 -low (m³ / sec) 0 0 0 0 0 00 00 00 - an Velocity Pressure (Pa) an Efficiency Grade = EG 80 0 0 40 0 0 - low (CM) (in Thousands). Performance certified is for Installation Type B & D: ree or ducted inlet, ducted outlet.. Power rating (kw) does not include transmission losses.. Performance ratings do not include the effects of appurtenances (accessories). 4. The sound power level ratings shown are in decibels, referred to E- watts calculated per AMCA Standard 0.. Values shown are for inlet LwiA sound power levels for Installation Type B: ree inlet, ducted outlet.. The A-weighted sound ratings shown have been calculated per AMCA Standard 0. 0 TWIN CITY AN - CATALOGUE M00

4,000 BC-DW 40 40 RPM LwA,000 960 RPM LwA kw kw 90kW. 600 400 00 RPM 0 RPM 8 LwA 0 LwA 9 LwA 0kW kw 8.kW kw kw kw kw 4kW kw.kw 0. 0. 00 00 RPM 9% Pk. Eff. 0 LwA LwA.kW 4kW kw 0. 0 80 66% Eff..kW.kW 4 6 8 0 40 -low (m³ / sec) 0 0 0 0 0 00 00 00 - an Velocity Pressure (Pa) an Efficiency Grade = EG 80 0 0 40 0 0 0 - low (CM) (in Thousands). Performance certified is for Installation Type B & D: ree or ducted inlet, ducted outlet.. Power rating (kw) does not include transmission losses.. Performance ratings do not include the effects of appurtenances (accessories). 4. The sound power level ratings shown are in decibels, referred to E- watts calculated per AMCA Standard 0.. Values shown are for inlet LwiA sound power levels for Installation Type B: ree inlet, ducted outlet.. The A-weighted sound ratings shown have been calculated per AMCA Standard 0.

0 4,000 BC-DW 44 40 RPM LwA,000 960 RPM P - an Total Pressure (Pa) 600 0 RPM 9 LwA 0 LwA LwA kw 4kW kw 60kW kw kw 90kW kw. 00 RPM 400 9% Pk. Eff. kw 8.kW 0kW 66% Eff. kw kw 00 0 40 60 -low (m³ / sec) 0 0 0 0 0 00 00 00 00 - an Velocity Pressure (Pa) an Efficiency Grade = EG 80 0 40 0 0 0 - low (CM) (in Thousands). Performance certified is for Installation Type B & D: ree or ducted inlet, ducted outlet.. Power rating (kw) does not include transmission losses.. Performance ratings do not include the effects of appurtenances (accessories). 4. The sound power level ratings shown are in decibels, referred to E- watts calculated per AMCA Standard 0.. Values shown are for inlet LwiA sound power levels for Installation Type B: ree inlet, ducted outlet.. The A-weighted sound ratings shown have been calculated per AMCA Standard 0. TWIN CITY AN - CATALOGUE M00

BC-DW 490 960 RPM,000 LwA 0 RPM. 600 400 00 RPM 8 LwA 9 LwA 0 LwA kw kw 4kW kw 0kW kw 8.kW 90kW kw 0. 00 RPM 00 9% Pk. Eff. LwA.kW kw 0. 66% Eff. 4kW.kW 0 8 0 40 60 -low (m³ / sec) 0 0 0 0 0 00 00 - an Velocity Pressure (Pa) an Efficiency Grade = EG 80 0 0 40 0 0 0 - low (CM) (in Thousands). Performance certified is for Installation Type B & D: ree or ducted inlet, ducted outlet.. Power rating (kw) does not include transmission losses.. Performance ratings do not include the effects of appurtenances (accessories). 4. The sound power level ratings shown are in decibels, referred to E- watts calculated per AMCA Standard 0.. Values shown are for inlet LwiA sound power levels for Installation Type B: ree inlet, ducted outlet.. The A-weighted sound ratings shown have been calculated per AMCA Standard 0.

BC-DW 4 960 RPM LwA,000 0 RPM 60kW kw 0 LwA kw. 600 400 00 00 RPM 00 RPM 8 LwA 9 LwA 4kW kw 0kW kw 8.kW kw kw 90kW kw kw 0. LwA.kW LwA 0. 0. 00 RPM 0 80 60 9% Pk. Eff. 0 LwA 66% Eff..kW kw 4kW.kW 8 0 40 60 80 -low (m³ / sec) 0 0 0 0 0 00 00 - an Velocity Pressure (Pa) an Efficiency Grade = EG 80 0 0 40 0 0 0 - low (CM) (in Thousands). Performance certified is for Installation Type B & D: ree or ducted inlet, ducted outlet.. Power rating (kw) does not include transmission losses.. Performance ratings do not include the effects of appurtenances (accessories). 4. The sound power level ratings shown are in decibels, referred to E- watts calculated per AMCA Standard 0.. Values shown are for inlet LwiA sound power levels for Installation Type B: ree inlet, ducted outlet.. The A-weighted sound ratings shown have been calculated per AMCA Standard 0. 4 TWIN CITY AN - CATALOGUE M00

4,000 BC-DW 600 960 RPM,000 0 RPM LwA LwA. 600 400 00 RPM 00 RPM 8 LwA 0 LwA 9 LwA kw 4kW kw 0kW kw 8.kW 60kW kw kw 90kW kw 00 kw 0. 0. 0. 00 RPM 0 80 9% Pk. Eff. LwA 66% Eff. kw 4kW.kW.kW kw 60 0 40 60 80 0 -low (m³ / sec) 0 0 0 0 0 00 00 00 - an Velocity Pressure (Pa) an Efficiency Grade = EG 80 0 40 0 0 0 00 - low (CM) (in Thousands). Performance certified is for Installation Type B & D: ree or ducted inlet, ducted outlet.. Power rating (kw) does not include transmission losses.. Performance ratings do not include the effects of appurtenances (accessories). 4. The sound power level ratings shown are in decibels, referred to E- watts calculated per AMCA Standard 0.. Values shown are for inlet LwiA sound power levels for Installation Type B: ree inlet, ducted outlet.. The A-weighted sound ratings shown have been calculated per AMCA Standard 0.

0 4,000 BC-DW 660 960 RPM LwA 0 RPM,000 LwA. 600 400 00 RPM 00 RPM 60kW 8 LwA 9 LwA 0 LwA LwA kw kw 90kW kw kw 4kW kw 0kW kw 0. 00 00 RPM 9% Pk. Eff. LwA 8.kW kw kw 0. 0 66% Eff..kW.kW 80 0 40 60 80 0 00 -low (m³ / sec) 0 0 0 0 0 00 00 00 00 00 - an Velocity Pressure (Pa) an Efficiency Grade = EG 80 0 0 0 0 00 00 - low (CM) (in Thousands). Performance certified is for Installation Type B & D: ree or ducted inlet, ducted outlet.. Power rating (kw) does not include transmission losses.. Performance ratings do not include the effects of appurtenances (accessories). 4. The sound power level ratings shown are in decibels, referred to E- watts calculated per AMCA Standard 0.. Values shown are for inlet LwiA sound power levels for Installation Type B: ree inlet, ducted outlet.. The A-weighted sound ratings shown have been calculated per AMCA Standard 0. 6 TWIN CITY AN - CATALOGUE M00

BC-DW 0 0 RPM,000 LwA 00 RPM LwA. 600 400 00 00 RPM 00 RPM 8 LwA 9 LwA 0 LwA kw 8.kW 4kW kw 0kW kw kw kw 90kW 60kW kw 0. LwA kw kw 0. 0 RPM 9% Pk. Eff. 0 LwA.kW.kW 0. 80 66% Eff. 4kW 60 0 0 0 80 0 00 -low (m³ / sec) 0 0 0 0 0 00 00 00 00 - an Velocity Pressure (Pa) an Efficiency Grade = EG 80 0 0 0 0 00 00 - low (CM) (in Thousands). Performance certified is for Installation Type B & D: ree or ducted inlet, ducted outlet.. Power rating (kw) does not include transmission losses.. Performance ratings do not include the effects of appurtenances (accessories). 4. The sound power level ratings shown are in decibels, referred to E- watts calculated per AMCA Standard 0.. Values shown are for inlet LwiA sound power levels for Installation Type B: ree inlet, ducted outlet.. The A-weighted sound ratings shown have been calculated per AMCA Standard 0.

4,000 BC-DW 80 0 RPM LwA,000 00 RPM LwA LwA. 600 400 00 RPM 00 RPM 8 LwA 9 LwA 0 LwA 0kW kw 4kW kw kw 90kW kw 60kW kw 00 kw 0. 0. RPM 9% Pk. Eff. LwA kw kw 8.kW 0. 0 80 66% Eff..kW.kW 60 0 0 0 80 0 00 -low (m³ / sec) 0 0 0 0 0 00 00 00 - an Velocity Pressure (Pa) an Efficiency Grade = EG 80 0 0 0 0 00 00 - low (CM) (in Thousands). Performance certified is for Installation Type B & D: ree or ducted inlet, ducted outlet.. Power rating (kw) does not include transmission losses.. Performance ratings do not include the effects of appurtenances (accessories). 4. The sound power level ratings shown are in decibels, referred to E- watts calculated per AMCA Standard 0.. Values shown are for inlet LwiA sound power levels for Installation Type B: ree inlet, ducted outlet.. The A-weighted sound ratings shown have been calculated per AMCA Standard 0. 8 TWIN CITY AN - CATALOGUE M00

0 4,000 BC-DW 890 0 RPM LwA,000 00 RPM LwA. 600 400 00 RPM 00 RPM 8 LwA 9 LwA 0 LwA kw LwA kw 90kW 60kW kw kw 4kW kw 0. 00 RPM 9% Pk. Eff. LwA 0kW kw kw 8.kW 0. 0 66% Eff. kw 80 0 0 0 80 0 00 00 -low (m³ / sec) 0 0 0 0 0 00 00 00 00 - an Velocity Pressure (Pa) an Efficiency Grade = EG 80 0 0 0 00 00 400 00 - low (CM) (in Thousands). Performance certified is for Installation Type B & D: ree or ducted inlet, ducted outlet.. Power rating (kw) does not include transmission losses.. Performance ratings do not include the effects of appurtenances (accessories). 4. The sound power level ratings shown are in decibels, referred to E- watts calculated per AMCA Standard 0.. Values shown are for inlet LwiA sound power levels for Installation Type B: ree inlet, ducted outlet.. The A-weighted sound ratings shown have been calculated per AMCA Standard 0. 9

,000 BC-DW 98 400 RPM LwA 00 RPM. 0. P - an Total Pressure (Pa) 600 400 00 RPM 9% Pk. Eff. 00 RPM 8 LwA 9 LwA 0 LwA kw kw 4kW kw 0kW 60kW kw kw 90kW 0. 66% Eff. kw 8.kW kw 0 40 60 80 0 00 -low (m³ / sec) 0 0 0 0 0 00 - an Velocity Pressure (Pa) an Efficiency Grade = EG 80 0 0 00 00 400 - low (CM) (in Thousands). Performance certified is for Installation Type B & D: ree or ducted inlet, ducted outlet.. Power rating (kw) does not include transmission losses.. Performance ratings do not include the effects of appurtenances (accessories). 4. The sound power level ratings shown are in decibels, referred to E- watts calculated per AMCA Standard 0.. Values shown are for inlet LwiA sound power levels for Installation Type B: ree inlet, ducted outlet.. The A-weighted sound ratings shown have been calculated per AMCA Standard 0. 60 TWIN CITY AN - CATALOGUE M00

DIMENSIONAL DATA Arrangement 9, SWSI Rotatable, Class I & II D HE GA GA. SIDES NOTE 4 HA C L DISCH. HC Q KL SD DIA. SHAT SE DX DISCH. LANGE KS KWY SIZE P OUTS. HSG. GB B GA. SCROLL OUTSIDE HOUSING A J C O.D. INLET K K L M AN HSG. C L C L AN SHAT M OUNDATION PLAN BH DIA. BASE HOLES GC G N H CW THD HG HN H HK HD HH HC HG HB H HA HE HE HD HJ HB HA HH HG HJ D D HN D D D D CW DBD CW TAD CW TAU CW UBD CW BAU CW BHD NOTES:. Discharge angles are included on all discharges except "TAD" and "DBD.". "CW" rotation is shown. "CCW" rotation is similar but opposite. *. Shaft diameter is increased to.8 on Hi-Temp. fans which require shaft coolers. 4. Standard Arr. 9 motor location is on the left for "CW" rotation units and on the right for "CCW" rotation. Dimension "R" equals max. motor frame. SIZE A B BH C D DX R G GA GB GC H HA HB HC HD HE H 0 48 68 90L 406.0.0 0 686 48 4 4 84 68 6 0 400 M 44.0.0 8 46 8 9 8 40 0 4 4 M 48.0.0 4 806 0 6 4 49 08 6 44 4 48 M.0.0 60 98 4 6 46 8 9 8 8 49 0 49 60M..0 86 64 68 60 44 99 00 8 40 4 4 8 60M 6..0 8 99 40 686 68 46 440 4 98 449 4 60 648 60L 69..0 46 49 449 6 69 9 484 46 4 69 494 4 66 60L 6..0 8 94 49 88 689 68 0 0 4 4 4 8 80M 88..0 49 4 4 96 64 6 89 4 SIZE HG HH HJ HK HN J K KL KS SD L M N P Q CLASS I CLASS II CLASS I CLASS II SE 6 99 9 89 46 64 8 x 8 x 68 64 * 8 60 4 60 440 6 0 60 64 8 x 8 x 4 8 649 8 * 8 89 0 9 489 40 0 6 8 x 8 x 4 66 00 0 9 6 8 9 8 44 46 9 6 8 x 8 x 0 6 6 * 0 9 8 6 98 490 6 08 89 8 x x 8 66 4 6 89 4 0 8 8 00 404 9 89 64 94 6 89 x 8 x 8 66 0 6 94 68 8 8 8 4 99 4 0 9 6 4 x 8 x 8 9 98 94 98 8 8 4 40 48 48 806 6 8 6 4 x 8 4 x 9 9 98 9 8 4 0 9 484 889 6 00 4 4 x 9 4 x 9 60 9 6 4 4 DIMENSIONS ARE NOT TO BE USED OR CONSTRUCTION. CERTIIED DRAWINGS AVAILABLE UPON REQUEST. 6

DIMENSIONAL DATA Arrangement & 9, SWSI Non-Rotatable, Class I & II HQ DC GA HE GA. SIDES MOTOR (ARR. 9 ONLY) SEE NOTE HA C L DISCH. HC Q KL SD DIA. SHAT SE DX DISCH. LANGE KS KWY SIZE P OUTS. HSG. OUTSIDE HOUSING A GB GA. SCROLL B BA J BASE ANGLES C O.D. INLET K K L M AN HSG. C L AN SHAT C L M AH DBD ONLY OUNDATION PLAN BH DIA. BASE HOLES GC G N CW THD H HG HP H HL HD HH HQ HC HG HB H HA HE HE HD HM (TAD ONLY) HB HA HH HG DA DB DD DE D DG CW DBD CW TAD CW TAU CW UBD CW BAU CW BHD NOTES:. Discharge angles are included on all discharges.. "CW" rotation is shown. "CCW" rotation is similar but opposite.. Standard Arr. 9 motor location is on the left for "CW" rotation units and on the right for "CCW" rotation. Dimension "R" equals max. motor frame. 4. or fans with inlet box at 90 degrees or 0 degrees, use "BAU" discharge dimension "D" for centerline height. SIZE A AH B BA BH C DA DB DC DD DE D DG DX R ARR. 9 G GA GB 00 808 48 60 6 x 6 4 80 69 69 69 69 4 6 90 8 80L 4.0. 0 89 484 66 6 x 6 4 88 6 6 6 6 8 8 99 8 00M 8.0. 6 98 4 6 x 6 4 98 49 8 90 4 8 00M 9.0. 40 8 9 808 x 8 8 86 88 89 940 0 6 8 00L 4.0. 44 9 66 894 x 9 899 9 90 98 6 99 8 S 4.0. 490 9 98 x 99 984 99 8 9 S 6.0. 4 4 808 89 x 0 4 94 8 4 0S.0. 600 6 88 x 0 604 4 9 46 68 0S 84.0. 660 994 6 90 x 6 4 46 499 600 86 64 0M 0.0. 0 96 8 46 90 x 949 4 8 448 68 68 6 0 64 0M.0.0 SIZE GC H HA HB HC HD HE H HG HH HL HM HP HQ J K KL KS CL I CL II 00 46 60 4 84 69 64 66 8 40 9 849 80 94 8 4 x 9 4 x 9 0 9 40 66 9 99 6 68 6 9 9 90 94 4 6 4 x 9 6 x 6 6 6 4 9 8 0 6 4 9 4 4 40 4 x 9 8 x 40 66 4 8 6 9 940 88 89 6 4 6 08 446 6 x 8 x 44 8 8 899 8 8 9 94 8 669 489 40 8 x 0 x 490 8 946 99 669 69 40 08 94 88 8 94 94 40 0 x 0 x 4 8 94 88 6 64 86 6 46 96 004 9 8 6 98 0 x x 4 600 9 0 0 66 9 80 9 4 60 0 66 0 x x 4 660 6 8 4 44 6 68 8 408 896 8 88 0 8 x 4 8 x 6 0 8 8 4 4 0 0 9 40 646 9 086 06 88 99 9 x 4 8 x 6 DIMENSIONS ARE NOT TO BE USED OR CONSTRUCTION. CERTIIED DRAWINGS AVAILABLE UPON REQUEST. 6 TWIN CITY AN - CATALOGUE M00

DIMENSIONAL DATA Arrangement & 9, Non-Rotatable, Class I & II (cont'd.) HQ DC GA HE GA. SIDES MOTOR (ARR. 9 ONLY) SEE NOTE HA C L DISCH. HC Q KL SD DIA. SHAT SE DX DISCH. LANGE KS KWY SIZE P OUTS. HSG. OUTSIDE HOUSING A GB GA. SCROLL B BA J BASE ANGLES C O.D. INLET K K L M AN HSG. C L AN SHAT C L M AH DBD ONLY OUNDATION PLAN BH DIA. BASE HOLES GC G N CW THD H HG HP H HL HD HH HQ HC HG HB H HA HE HE HD HM (TAD ONLY) HB HA HH HG DA DB DD DE D DG CW DBD CW TAD CW TAU CW UBD CW BAU CW BHD NOTES:. Discharge angles are included on all discharges.. "CW" rotation is shown. "CCW" rotation is similar but opposite.. Standard Arr. 9 motor location is on the left for "CW" rotation units and on the right for "CCW" rotation. Dimension "R" equals max. motor frame. 4. or fans with inlet box at 90 degrees or 0 degrees, use "BAU" discharge dimension "D" for centerline height. SIZE L M N P Q SD CL I CL II SE 00 68 40 9 40 0 0 46 0 49 44 9 44 0 46 6 49 480 9 6 489 0 6 46 40 6 0 40 6 46 44 80 8 4 9 6 0 9 490 8 64 46 6 0 9 4 90 0 48 646 90 600 94 8 48 69 80 90 660 99 84 60 8 88 90 0 9 0 6 94 60 008 98 90 0 DIMENSIONS ARE NOT TO BE USED OR CONSTRUCTION. CERTIIED DRAWINGS AVAILABLE UPON REQUEST. 6

DIMENSIONAL DATA Arrangement, SWSI Non-Rotatable, Class I & II HQ DC GA HE GA. SIDES NOTE HA C L DISCH. HC Q KL SD DIA. SHAT SE DX DISCH. LANGE KS KWY SIZE P OUTS. HSG. OUTSIDE HOUSING A GB B GA. SCROLL J BA BASE ANGLES C O.D. INLET K K L M AN HSG. C L AN SHAT C L M AH DBD ONLY OUNDATION PLAN BH DIA. BASE HOLES GC G N CW THD H HG HP H HL HD HH HQ HC HG HB H HA HE HE HB HM (TAD ONLY) HB HA HH HG DA DB DD DE D DG CW DBD CW TAD CW TAU CW UBD CW BAU CW BHD NOTES:. Discharge angles are included on all discharges.. "CW" rotation is shown. "CCW" rotation is similar but opposite.. rame supports vary in contruction by size and by discharge position. 4. or fans with inlet box at 90 degrees or 0 degrees, use "BAU" discharge dimension "D" for centerline height. SIZE A AH B BA BH C DA DB DC DD DE D DG DX G GA GB GC 80 9 66 90 x 6 60 600 89 94 6 64 46 890 9 6 8 90 x 8 664 9 8 988 9 48 64 0 98 64 6 969 x 69 9 86 94 0 9 0 64 099 49 SIZE H HA HB HC HD HE H HG HH HL HM HP HQ J K KL KS CL I CL II 80 0 60 0 880 6 66 6 4 888 84 94 9 960 8 0 8 x 6 x 8 890 8 99 4 0 946 80 99 8 0 4 4 9 0 8 x 6 x 8 98 9 0 00 88 0 89 64 8 0 88 6 64 0 x 8 enq SIZE L M N P Q SD CL I CL II SE 80 4 8 60 80 8 0 9 890 9 8 60 8 9 0 9 98 99 6 enq 9 64 TWIN CITY AN - CATALOGUE M00

DIMENSIONAL DATA Arrangement, SWSI Non-Rotatable, Class I & II DC GA HE GA. SIDES HA C L DISCH. Q HC SD DIA. SHAT DX DISCH. LANGE KL P OUTS. HSG. KS KWY SIZE GB GA. SCROLL B BA OUTSIDE HOUSING A J BASE ANGLES C O.D. INLET K K BH DIA. BASE HOLES M C L AN SHAT AN HSG. C L M DBD ONLY AH OUNDATION PLAN GC GD CW THD N H HG HP H HL HD HH HC HG HB H HA HE HE HD HM (TAD ONLY) HB HA HH HG DA DB DD DE D DG GC G GC G GC G GC G CW DBD CW TAD CW TAU CW UBD GC G CW BAU GC GD CW BHD NOTES:. Discharge angles are included on all discharges.. Inlet bearing bar support is removable.. "CW" rotation is shown. "CCW" rotation is similar but opposite. 4. Bearing bar supports may extend beyond base angles. See Drawing AC008 for dimensions if space limitations are required for mounting fan. SIZE A AH B BA BH C DA DB DC DD DE D DG DX G GA GB GC 0 9 48 8 x 8 48 8 60 9 9 8 0.0.0 6 9 8 x 8 0 406 86 0 4 4.0.0 6 40 4 0 8 x 8 4 0 4 6 4 8.0.0 89 6 44 48 8 x 0 4 4 44 4 68 8 4 49 66.0.0 08 8 49 0 8 x 0 49 68 40 400 4 4 46 660..0 0 00 8 9 40 8 x 0 4 4 40 49 4 48 464 489 9..0 6 98 449 0 x 0 4 60 449 4 489 9 660 94..0 9 4 69 9 494 0 x 0 4 66 49 9 08 40 6 8 8..0 4 0 9 4 0 x 0 4 4 4 9 9 9 69 66 8 8 94..0 4 SIZE GD H HA HB HC HD HE H HG HH HL HM HP J K KL KS CLASS I CLASS II 40 4 48 4 4 84 68 6 44 6 89 46 64 8 x 8 x 0 46 8 9 8 60 4 6 46 400 0 60 64 8 x 8 x 46 8 0 6 4 49 08 89 0 660 08 440 0 6 8 x 8 x 6 66 48 4 6 46 8 9 8 8 9 08 49 46 9 6 8 x 8 x 8 660 4 68 60 44 99 4 6 4 89 8 x x 8 00 08 40 686 68 46 440 4 86 9 8 608 88 94 89 x 8 x 8 94 449 6 69 9 484 46 4 99 96 66 648 6 4 x 8 x 8 4 8 9 49 88 689 68 0 40 48 988 06 08 8 6 4 x 8 4 x 9 0 94 64 4 96 64 6 89 4 9 484 6 9 6 6 00 4 x 8 4 x 9 DIMENSIONS ARE NOT TO BE USED OR CONSTRUCTION. CERTIIED DRAWINGS AVAILABLE UPON REQUEST. 6

DIMENSIONAL DATA Arrangement, SWSI Non-Rotatable, Class I & II (cont'd.) DC GA HE GA. SIDES HA C L DISCH. Q HC SD DIA. SHAT DX DISCH. LANGE KL P OUTS. HSG. KS KWY SIZE GB GA. SCROLL B BA OUTSIDE HOUSING A J BASE ANGLES C O.D. INLET K K BH DIA. BASE HOLES M C L AN SHAT AN HSG. C L M DBD ONLY AH OUNDATION PLAN GC GD CW THD N H HG HP H HL HD HH HC HG HB H HA HE HE HD HM (TAD ONLY) HB HA HH HG DA DB DD DE D DG GC G GC G GC G GC G CW DBD CW TAD CW TAU CW UBD GC G CW BAU GC GD CW BHD NOTES:. Discharge angles are included on all discharges.. Inlet bearing bar support is removable.. "CW" rotation is shown. "CCW" rotation is similar but opposite. 4. Bearing bar supports may extend beyond base angles. See Drawing AC008 for dimensions if space limitations are required for mounting fan. SIZE M N P SD Q CL I CL II CL I CL II 6 4 4 64 8 6 68 68 8 6 9 0 00 0 6 0 8 4 4 0 8 00 0 89 89 68 8 8 98 44 44 98 8 8 4 49 468 9 8 4 0 9 48 49 6 8 4 DIMENSIONS ARE NOT TO BE USED OR CONSTRUCTION. CERTIIED DRAWINGS AVAILABLE UPON REQUEST. 66 TWIN CITY AN - CATALOGUE M00

DIMENSIONAL DATA Arrangement, SWSI Non-Rotatable, Class I & II HQ DC GA HE GA. SIDES HA C L DISCH. HC Q SD DIA. SHAT DX DISCH. LANGE KL P OUTS. HSG. KS KWY SIZE GB GA. SCROLL B BA J OUTSIDE HOUSING A BASE ANGLES C O.D. INLET K K BH DIA. BASE HOLES M C L AN SHAT C L AN HSG. M DBD ONLY AH OUNDATION PLAN GC G CW THD N H HG HP H HL HD HH HQ HC HG HB H HA HE HE HD HM (TAD ONLY) HB HA HH HG DA DB DD DE D DG CW DBD CW TAD CW TAU CW UBD CW BAU CW BHD NOTES:. Discharge angles are included on all discharges.. Inlet bearing bar support is removable.. "CW" rotation is shown. "CCW" rotation is similar but opposite. 4. rame supports vary in construction by size and by discharge position.. Bearing bar supports may extend beyond base angles. See Drawing AC008 for dimensions if space limitations are required for mounting fan. SIZE A AH B BA BH C DA DB DC DD DE D DG DX G GA GB GC 00 808 48 60 6 x 6 4 80 60 660 6 660 4 49 80 8 4.0. 0 89 484 66 6 x 6 4 88 66 0 686 4 8 89 946 8 8.0. 9 6 98 4 6 x 6 4 98 49 8 90 4 8 9.0. 6 40 8 9 808 x 8 8 86 88 89 940 0 6 8 4.0. 66 44 9 66 894 x 9 899 9 90 98 6 99 8 4.0. 8 490 9 98 x 99 984 99 8 9 6.0. 8 4 4 808 89 x 0 4 94 8 4.0. 8 600 6 88 x 0 604 4 9 46 68 84.0. 9 660 994 6 90 x 6 4 46 499 600 86 64 0.0. 6 0 96 8 46 90 x 949 4 8 448 68 68 6 0 64.0.0 8 SIZE H HA HB HC HD HE H HG HH HL HM HP HQ J K KL KS CLASS I CLASS II 00 4 60 4 84 69 64 66 8 40 9 849 80 406 8 4 x 9 4 x 9 0 9 66 9 99 6 68 6 9 9 90 94 4 6 4 x 9 6 x 6 86 4 9 8 0 6 4 9 4 484 40 4 x 9 8 x 40 96 8 6 9 940 88 89 6 4 6 446 4 x 9 8 x 44 48 899 8 8 9 94 8 666 6 489 40 4 x 9 0 x 490 4 99 669 69 40 08 94 88 8 94 6 40 6 x 0 x 4 9 94 88 6 64 86 6 46 96 004 9 8 6 98 8 x 0 x 600 40 0 66 9 80 9 4 60 0 66 0 x x 4 660 8 8 4 44 6 68 8 408 896 8 88 0 8 0 x 8 x 6 0 8 4 4 0 0 9 40 646 9 086 06 886 99 9 x 4 8 x 6 DIMENSIONS ARE NOT TO BE USED OR CONSTRUCTION. CERTIIED DRAWINGS AVAILABLE UPON REQUEST. 6

DIMENSIONAL DATA Arrangement, SWSI Non-Rotatable, Class I & II HQ DC GA HE GA. SIDES HA C L DISCH. HC Q SD DIA. SHAT DX DISCH. LANGE KL P OUTS. HSG. KS KWY SIZE GB GA. SCROLL B BA J OUTSIDE HOUSING A BASE ANGLES C O.D. INLET K K BH DIA. BASE HOLES M C L AN SHAT C L AN HSG. M DBD ONLY AH OUNDATION PLAN GC G CW THD N H HG HP H HL HD HH HQ HC HG HB H HA HE HE HD HM (TAD ONLY) HB HA HH HG DA DB DD DE D DG CW DBD CW TAD CW TAU CW UBD CW BAU CW BHD NOTES:. Discharge angles are included on all discharges.. Inlet bearing bar support is removable.. "CW" rotation is shown. "CCW" rotation is similar but opposite. 4. rame supports vary in construction by size and by discharge position.. Bearing bar supports may extend beyond base angles. See Drawing AC008 for dimensions if space limitations are required for mounting fan. SIZE M N P SD Q CL I CL II CL I CL II 00 40 9 40 40 4 0 0 44 9 6 8 44 4 6 480 9 60 66 489 0 6 40 0 64 664 40 0 6 44 8 69 4 9 0 0 490 64 68 84 6 0 4 0 48 848 8 6 600 8 48 90 9 80 90 660 84 60 88 0 0 94 60 8 98 90 0 DIMENSIONS ARE NOT TO BE USED OR CONSTRUCTION. CERTIIED DRAWINGS AVAILABLE UPON REQUEST. 68 TWIN CITY AN - CATALOGUE M00

DIMENSIONAL DATA Arrangement, SWSI Non-Rotatable, Class I & II HQ DC GA HE GA. SIDES NOTE 4 HA C L DISCH. Q HC SD DIA. SHAT DX DISCH. LANGE KL P OUTS. HSG. KS KWY SIZE GB GA. SCROLL B BA J OUTSIDE HOUSING A BASE ANGLES C O.D. INLET K K BH DIA. BASE HOLES M C L AN SHAT C L AN HSG. M AH DBD ONLY OUNDATION PLAN GC G CW THD N H HG HP H HL HD HH HQ HC HG HB H HA HE HE HD HM (TAD ONLY) HB HA HH HG DA DB DD DE D DG CW DBD CW TAD CW TAU CW UBD CW BAU CW BHD NOTES:. Discharge angles are included on all discharges.. Inlet bearing bar support is removable.. "CW" rotation is shown. "CCW" rotation is similar but opposite. 4. rame supports vary in contruction by size and by discharge position.. Bearing bar supports may extend beyond base angles. See Drawing AC008 for dimensions if space limitations are required for mounting fan. SIZE A AH B BA BH C DA DB DC DD DE D DG DX G GA GB GC 80 9 66 90 x 6 60 600 89 94 6 64 46 890 9 6 8 90 x 8 664 9 8 988 9 484 64 0 98 64 6 969 0 x 69 9 86 94 0 9 0 64 099 49 SIZE H HA HB HC HD HE H HG HH HL HM HP HQ J K KL KS CL I CL II 80 80 60 0 880 6 66 6 4 888 84 94 9 988 8 0 8 x 6 x 8 890 0 8 99 4 0 946 80 99 8 0 4 9 9 0 8 x 6 x 8 98 9 0 00 88 0 89 64 8 0 88 6 64 0 x 8 enq SIZE M N P SD Q CL I CL II CL I CL II 80 8 60 9 8 0 890 8 60 89 9 0 98 44 40 6 enq DIMENSIONS ARE NOT TO BE USED OR CONSTRUCTION. CERTIIED DRAWINGS AVAILABLE UPON REQUEST. 69

DIMENSIONAL DATA Arrangement, SWSI Non-Rotatable, Class III DC GA HE GA. SIDES HA C L DISCH. HC Q KL SD DIA. SHAT SE DX DISCH. LANGE KS KWY SIZE P OUTS. HSG. OUTSIDE HOUSING A GB B GA. SCROLL BA J BASE ANGLES C O.D. INLET K K L M AN HSG. C L C L AN SHAT M AH DBD ONLY BH DIA. BASE HOLES OUNDATION PLAN GC GD CW THD H N HG HP H HL HD HH HC HG HB H HA HE HE HD HM (TAD ONLY) HB HA HH HG DA DB DD DE D DG G CW DBD GC G CW TAD GC G CW TAU GC G CW UBD GC G CW BAU GC GD CW BHD GC NOTES:. Discharge angles are included on all discharges.. "CW" rotation is shown. "CCW" rotation is similar but opposite.. or fans size 8-0 (except TAD 8-00) with inlet box at 90 degrees or 0 degrees, use "BAU" discharge dimension "D" for centerline height. SIZE A AH B BA BH C DA DB DC DD DE D DG DX G GA GB GC 4 94 8 x 0 48 8 60 9 9 94 0 6 8 8 x 0 0 406 86 0 4 4 6 406 9 06 8 x 0 4 0 4 6 40 8 89 6 446 49 8 8 x 0 4 4 44 4 68 8 4 49 66 08 8 49 6 0 x 0 4 49 68 40 400 4 4 9 686 4 00 4 9 406 0 x 0 4 4 40 49 4 48 464 489 6 68 60 4 4 6 x 6 4 60 449 4 489 9 6 89 4 4 66 499 6 x 6 4 66 49 9 08 40 6 0 8 86 48 0 4 4 48 6 x 6 4 4 4 9 9 9 69 66 8 940 40 00 8 4 608 x 80 60 660 6 660 699 49 88 8 6 0 89 499 66 x 88 66 0 686 4 6 89 99 8 4 SIZE GD H HA HB HC HD HE H HG HH HL HM HP J K KL KS 4 68 48 4 6 86 0 4 8 8 46 8 0 4 6 x 8 0 6 4 9 4 9 9 6 4 6 484 44 6 68 6 x 8 49 66 0 4 9 9 6 6 44 0 8 89 4 x 9 6 88 08 4 4 84 60 40 9 98 9 4 494 46 98 89 4 x 9 8 686 6 68 60 4 4 400 6 9 89 9 4 6 4 4 4 x 9 00 86 40 68 0 46 44 44 8 60 846 6 89 9 4 4 x 9 89 946 449 64 60 486 4 49 400 9 68 66 4 60 4 x 9 4 86 49 84 699 0 4 44 988 699 4 8 84 8 x 0 940 4 4 9 6 60 9 48 68 4 9 6 8 x 00 6 60 6 846 699 66 6 9 8 8 884 406 46 8 8 x 0 4 6 66 9 90 6 69 6 94 86 88 969 4 8 0 x DIMENSIONS ARE NOT TO BE USED OR CONSTRUCTION. CERTIIED DRAWINGS AVAILABLE UPON REQUEST. 0 TWIN CITY AN - CATALOGUE M00

DIMENSIONAL DATA Arrangement, SWSI Non-Rotatable, Class III (cont'd.) DC GA HE GA. SIDES HA C L DISCH. HC Q KL SD DIA. SHAT SE DX DISCH. LANGE KS KWY SIZE P OUTS. HSG. OUTSIDE HOUSING A GB B GA. SCROLL BA J BASE ANGLES C O.D. INLET K K L M AN HSG. C L C L AN SHAT M AH DBD ONLY BH DIA. BASE HOLES OUNDATION PLAN GC GD CW THD H N HG HP H HL HD HH HC HG HB H HA HE HE HD HM (TAD ONLY) HB HA HH HG DA DB DD DE D DG G CW DBD GC G CW TAD GC G CW TAU GC G CW UBD GC G CW BAU GC GD CW BHD GC NOTES:. Discharge angles are included on all discharges.. "CW" rotation is shown. "CCW" rotation is similar but opposite.. or fans size 8-0 (except TAD 8-00) with inlet box at 90 degrees or 0 degrees, use "BAU" discharge dimension "D" for centerline height. SIZE L M N P Q SD SE 9 6 48 64 8 89 0 8 08 8 8 89 4 0 00 4 6 4 89 4 8 6 4 66 4 4 00 9 0 699 68 0 49 9 9 9 98 0 40 4 8 9 884 9 60 6 0 48 9 960 6 60 6 00 48 9 40 6 9 0 4 44 0 9 DIMENSIONS ARE NOT TO BE USED OR CONSTRUCTION. CERTIIED DRAWINGS AVAILABLE UPON REQUEST.

DIMENSIONAL DATA Arrangement, SWSI Non-Rotatable, Class III HQ DC GA HE GA. SIDES HA C L DISCH. HC Q KL SD DIA. SHAT SE DX DISCH. LANGE KS KWY SIZE P OUTS. HSG. OUTSIDE HOUSING A GB B GA. SCROLL BA J BASE ANGLES C O.D. INLET K K L M AN HSG. C L C LAN SHAT M AH DBD ONLY BH DIA. BASE HOLES OUNDATION PLAN GC G CW THD H N HG HP H HL HD HH HQ HC HG HB H HA HE HE HD HM (TAD ONLY) HB HA HH HG DA DB DD DE D DG CW DBD CW TAD CW TAU CW UBD CW BAU CW BHD NOTES:. Discharge angles are included on all discharges.. "CW" rotation is shown. "CCW" rotation is similar but opposite.. or fans with inlet box at 90 degrees or 0 degrees, use "BAU" discharge dimension "D" for centerline height. SIZE A AH B BA BH C DA DB DC DD DE D DG DX G GA GB GC 6 988 x 98 4 49 8 90 4 8 x 8 4 6 40 8 69 8 x 0 8 8 806 88 89 940 0 6 0 x 0 4 66 44 68 89 x 0 9 899 9 90 98 6 99 0 x 0 4 8 490 4 4 984 x 0 99 984 99 8 9 0 x 0 6 8 4 46 8 9 90 x 4 94 8 4 4 6 x 6 8 600 68 94 90 x 604 4 9 46 69 6 x 6 880 940 660 9 0 x 6 4 46 499 600 8 6 x 6 0 6 0 96 46 0 x 949 4 8 448 68 68 6 064 6 x 6 8 80 69 0 x 6 60 600 89 94 6 x 6 4 6 890 94 8 0 x 8 664 9 8 988 9 496 6 x 6 6 SIZE H HA HB HC HD HE H HG HH HL HM HP HQ J K KL KS CLASS I L M 6 4 4 84 80 4 06 69 400 99 9 40 4 8 0 x 4 40 66 8 6 4 94 88 80 8 4 84 46 0 0 x 6 8 44 88 899 8 48 4 9 96 89 80 69 4 99 6 0 0 x 4 686 68 490 94 99 669 4 946 88 840 4 69 46 9 x 4 6 4 08 94 849 6 8 8 48 98 06 4 84 8 699 6 9 8 x 6 49 689 600 04 66 99 4 9 8 4 468 40 68 6 60 4 x 8 86 6 660 499 9 84 44 8 4 6 9 88 84 44 4 x 8 889 89 0 4 4 04 99 408 648 06 9 8 6 x 8 96 90 80 940 60 88 6 66 4 90 8 4 988 889 6 x 8 4 890 8 8 99 4 0 948 8 6 600 99 00 4 464 68 90 9 enq 8 6 DIMENSIONS ARE NOT TO BE USED OR CONSTRUCTION. CERTIIED DRAWINGS AVAILABLE UPON REQUEST. TWIN CITY AN - CATALOGUE M00

TYPICAL SPECIICATIONS Model BC-SW ans shall be Model BC Backward Inclined, as manufactured by Twin City an & Blower, Minneapolis, Minnesota. PERORMANCE ans shall be tested in accordance with AMCA and AMCA 00 test codes for air moving devices and shall be licensed to bear the AMCA certified ratings seal for both sound and air. ans shall have a sharply rising pressure characteristic extending through the operating range and continuing to rise beyond the efficiency peak to ensure quiet and stable operation. ans shall have a non-overloading design with self-limiting power characteristics and shall reach a peak in the normal selection area. All fans shall be capable of operating over the minimum pressure class limits, as specified in AMCA Standard 99-408. HOUSING BC fan housings shall be of heavy gauge, continuously welded construction. Housings with lock seams or partially welded construction are not acceptable. Discharge flanges are to be provided for rigidity and duct connection. Housings shall be suitably braced to prevent vibration or pulsation. Housings shall have tapered spun, aerodynamically designed inlet cones or funnels providing stable flow and high rigidity. Class I and II sizes 0 and smaller shall be of the rotatable design, convertible to 8 standard discharge configurations. IMPELLER BC backward inclined impellers shall be single thickness plate type, designed for maximum efficiency and quiet operation, and shall be solid welded to the rim and back plate. Partial welding will not be acceptable on aerofoil or backward inclined blades. All impellers shall be statically and dynamically balanced. SHAT Shafts shall be AISI 40 or 4 hot rolled steel, accurately turned, ground, polished, and ring gauged for accuracy. Shafts shall be sized for the first critical speed of at least.4 times the maximum speed. BEARINGS Bearings shall be heavy duty, grease lubricated, spherical roller or adapter mounted anti-friction ball, self-aligning, pillow block type and selected for a minimum average bearing life L- in excess of 40,000 hours at the maximum fan RPM. DRIVE Motor sheaves shall be cast iron, variable pitch on applications. kw and smaller, and fixed pitch on kw and larger. Drives and belts shall be located external to the fan casing and rated for % of the required motor rating. INISH AND COATING The entire fan assembly, excluding the shaft, shall be thoroughly degreased and deburred before application of a rust-preventative primer. After the fan is completely assembled, a finish coat of paint shall be applied to the entire assembly. The fan shaft shall be coated with a petroleum-based rust protectant. ACCESSORIES When specified, accessories such as belt guards, weather covers, access doors, companion flanges, variable inlet vanes, outlet dampers, piezometer ring airflow measurement device, inlet boxes, shaft coolers, shaft seals, inlet screens, etc., shall be provided by Twin City an & Blower to maintain one source responsibility. When specified, fans shall be supplied with internal or nested type variable inlet vanes for impeller diameters 40 mm and larger. Cantilevered vane blades are to be used through Size 660 to minimize air performance insertion losses and noise. The operating mechanism shall be out of the inlet airstream. ACTORY BALANCE AND RUN TESTING All fan impellers shall be statically and dynamically balanced in accordance with ANSI/AMCA 04 Balance Quality and Vibration Levels for ans to a Balance Quality Grade G6., (.8 mm/s rms). All assembled fans are test run at the rated operating speed or at the maximum RPM of the fan. Vibration readings are recorded in the horizontal, vertical and axial directions on both bearings. Trim balancing is performed if necessary to maintain vibration limits. Records shall be maintained and a written copy shall be available upon request. GUARANTEE The manufacturer shall guarantee the workmanship and materials for its BC Backward Inclined fans for at least twelve () months from start-up or eighteen (8) months from shipment, whichever occurs first.

TYPICAL SPECIICATIONS Model BC-DW ans shall be Model BC Backward Inclined, as manufactured by Twin City an & Blower, Minneapolis, Minnesota. PERORMANCE ans shall be tested in accordance with AMCA test codes for air moving devices and shall be licensed to bear the AMCA certified ratings seal for air. ans shall have a sharply rising pressure characteristic extending through the operating range and continuing to rise beyond the efficiency peak to ensure quiet and stable operation. ans shall have a non-overloading design with self-limiting power characteristics and shall reach a peak in the normal selection area. All fans shall be capable of operating over the minimum pressure class limits, as specified in AMCA Standard 408-69. HOUSING BC fan housings shall be of heavy gauge, continuously welded construction. Housings with lock seams or partially welded construction are not acceptable. Housings shall be suitably braced to prevent vibration or pulsation. Housings shall have spun, aerodynamically designed inlet cones or inlet venturies for smooth airflow into the impellers. IMPELLER Impellers shall have tapered spun impeller cones or shrouds, providing stable flow and high rigidity. Impellers shall be of the non-overloading type. BC backward inclined impellers shall be single thickness plate type, continuously welded to the rim and back plate. Blades shall be designed for maximum efficiency and quiet operation. Partial welding will not be acceptable on aerofoil or backward inclined blades. Smaller sizes may use extruded aluminium blades. All impellers shall be statically and dynamically balanced. The complete fan assembly shall be test balanced at the operating speed prior to shipment. SHAT Shafts shall be AISI 40 or 4 hot rolled steel, accurately turned, ground, polished, and ring gauged for accuracy. Shafts shall be sized for the first critical speed of at least.4 times the maximum speed. BEARINGS Bearings shall be heavy duty, grease lubricated, spherical roller or adapter mounted anti-friction ball, self-aligning, pillow block type and selected for a minimum average bearing life L- in excess of 40,000 hours at the maximum fan RPM. DRIVE Motor sheaves shall be cast iron, variable pitch on applications. kw and smaller, and fixed pitch on kw and larger. Drives and belts shall be located external to the fan casing and rated for % of the required motor rating. INISH AND COATING The entire fan assembly, excluding the shaft, shall be thoroughly degreased and deburred before application of a rust-preventative primer. After the fan is completely assembled, a finish coat of paint shall be applied to the entire assembly. The fan shaft shall be coated with a petroleum-based rust protectant. ACCESSORIES When specified, accessories such as belt guards, access doors, companion flanges, variable inlet vanes, outlet dampers, piezometer ring airflow measurement device, inlet boxes, shaft coolers, shaft seals, inlet screens, etc., shall be provided by Twin City an & Blower to maintain one source responsibility. When specified, fans shall be supplied with internal or nested type variable inlet vanes for impeller diameters 40 mm and larger. Cantilevered vane blades are to be used through Size 660 to minimize air performance insertion losses and noise. The operating mechanism shall be out of the inlet airstream. Double width fans shall have interconnecting linkage to ensure operation in unison. ACTORY BALANCE AND RUN TESTING All fan impellers shall be statically and dynamically balanced in accordance with ANSI/AMCA 04 Balance Quality and Vibration Levels for ans to a Balance Quality Grade G6. (.8 mm/s rms). All assembled fans are test run at the rated operating speed or at the maximum RPM of the fan. Vibration readings are recorded in the horizontal, vertical and axial directions on both bearings. Trim balancing is performed if necessary to maintain vibration limits. Records shall be maintained and a written copy shall be available upon request. GUARANTEE The manufacturer shall guarantee the workmanship and materials for its BC Backward Inclined fans for at least twelve () months from start-up or eighteen (8) months from shipment, whichever occurs first. 4 TWIN CITY AN - CATALOGUE M00