MOBILE MIXERS PARTS MANUAL 900SD TRUCK, TRAILER, STATIONARY HARSH INTERNATIONAL, INC. 600 OAK AVE. EATON, COLORDO 80615-007 MAIN NUMBER: (970) 454-2291 FAX: (970) 454-3491 PRICE: $2.50 PARTS BOOK NUMBER:
PARTS ORDERING INFORMATION To assure continued safe and efficient operation and to maintain the validity of your warranty use only genuine Harsh replacement parts. To obtain the correct parts for your mixer contact the nearest Harsh equipment dealer in your area. If no Harsh dealer is available, contact Harsh International Inc., 600 Oak Avenue, Eaton, CO 80615, (970) 454-2291. When ordering parts, be sure to know the Model and Serial numbers of the machine. For the quickest service when ordering by phone, be prepared to state the part number and description as well as the Parts Manual part number, the page number and item number of the part(s) you are ordering. Always have repairs performed by qualified Service Personnel from your Harsh dealer. All information, illustrations and specifications contained in this manual are based on the latest product information available at the time of printing. Harsh International, Inc. reserves the right to make changes to manuals, parts or assemblies at any time without prior notice. REPLACEMENT MANUALS Replacement or extra Operator's Manuals and Parts Manuals are available from Harsh or contact your local dealer. All Operator's Manuals and Parts Manuals are ordered by Model number and Serial number of your unit. There is a nominal cost for each manual ordered.!!!! IMPORTANT!!!! Before attempting to operate, inspect, adjust, repair or replace any part of your machine be sure to be thoroughly familiar with your Operator's Manual and observe all safety notices; both printed in the manual and on decals located on the machine. FAILURE TO OBSERVE THESE SAFETY RULES COULD RESULT IN SERIOUS INJURY AND/OR PROPERTY DAMAGE! 2 P age
INDEX GROUPS PAGE # SUB FRAME GROUP 900 LOAD CELL (4X4) & PARTS LIST 4 SUB-FRAME GROUP 900 LOAD CELL (6X6) & PART LIST 5 SUB-FRAME GROUP HYDRO HD (900) & PARTS LIST 6 900 SD HYDROSTATIC DRIVE COMPONENTS & PARTS LIST 7 AUGER GROUP, 900 FEED EZ MIX (1/2 FLT) ASSEMBLY (A8255) 8 AUGER GROUP - 900 FEED EZ MIX (1/2 FLT) ASSEMBLY & PARTS LIST 9 AUGER GROUP - 900 SD FEED 4 15/16 SHAFTS (A8028) 10 AUGER GROUP - 900 SD FEED 4 15/16 SHAFTS PARTS LIST 11 AUGER GROUP 900 SD FEED(3/4 FLT) 4 15/16 SHAFTS 12 AUGER GROUP 900 SD FEED(3/4 FLT) 4 15/16 SHAFTS PARTS LIST 13 AUGER 900 FEED RH DISCHARGE, 16 (A8151) & PARTS LIST 14 AUGER GROUP, 900 FEED EZ NO OUTBOARD 15 AUGER GROUP, 900 FEED EZ NO OUTBOARD PARTS LIST 16 AUGER GROUP, 900 SD RCL SPECIAL (A8393) 17 AUGER GROUP, 900 SD RCL SPECIAL PARTS LIST 18 REAR DRIVE GROUP 900 SD 4 15/16 BEARINGS & PARTS LIST (A8029) 19 REAR DRIVE GROUP 900 SD MIXER (3 15/16) BEARINGS & PARTS LIST (A8026) 20 REAR DRIVE GROUP 900 SD (A8231) 21 REAR DRIVE GROUP 900 SD PARTS LIST 22 DISCHARGE GROUP, TRIPLE SHORT (NEW) (A8262) 23 DISCHARGE GROUP, TRIPLE SHORT (NEW) PARTS LIST 24 DISCHARGE GROUP, TRIPLE MED (NEW) (A8279) 25 DISCHARGE GROUP, TRIPLE MED (NEW) PARTS LIST 26 DISCHARGE GROUP TRIPLE SHORT (33 ) (A7669) 27 DISCHARGE GROUP TRIPLE SHORT (33 ) PARTS LIST 28 DISCHARGE GROUP TRIPLE MED (40 ) (A7709) 29 DISCHARGE GROUP TRIPLE MED (40 ) PARTS LIST 30 DISCHARGE GROUP TRIPLE 9 EXTENDED (48 ) (A7710) 31 DISCHARGE GROUP TRIPLE 9 EXTENDED (48 ) PARTS LIST 32 DISCHARGE GROUP TRIPLE DOUBLE SHORT (33 ) (A8020) 33 DISCHARGE GROUP TRIPLE DOUBLE SHORT (33 ) PARTS LIST 34 RH DISCHARGE GROUP TIRPLE SHORT (33 ) (A8021) 35 RH DISCHARGE GROUP TIRPLE SHORT (33 ) PARTS LIST 36 DOOR GROUP, OIL BATH 900 SD, 1200 (A8034) & PARTS LIST 37 TUB GROUP, 900 SD TRIPLE DISCHARGE (A8030) & PARTS LIST 38 TUB GROUP, 900 SD TRIPLE DISCHARGE (A8105) & PARTS LIST 39 3 P age
SUB-FRAME GROUP 900 LOAD CELL (4X4) & PARTS LIST NOTES: BOLT SIDE MOUNT PLATES TO SUB-FRAME MOUNTS FOR LATER ASSEMBLY. QTY ITEM PART # DESCRIPTION QTY ITEM PART # DESCRIPTION 1 1 A18856 SUB FRAME ASSEMBLY, 4 X 4, SCREW, HX HD CAP, 3/4-16 12 5 100824 LOAD CELL, HYDRO, 900 UNF X 2 GR5 24 2 100556 WASHER, FLAT, 3/4 SIDE MOUNT PLATE, TRUCK 6 6 19207 MOUNT,25 12 3 100252 NUT, HEX, 3/4-16 UNF GR5 PEDESTAL ASSEMBLY, 4 7 A8098 (500,700,900) 12 4 100554 WASHER, LOCK, 3/4 4 P age
SUB-FRAME GROUP 900 LOAD CELL (6X6) & PARTS LIST LOAD CELL PED ASSY NOTES: BOLT SIDE MOUNT PLATES TO SUB-FRAME FOR LATER ASSEMBLY. (SEE PARTS KITS A1917) QTY ITEM PART # DESCRIPTION QTY ITEM PART # DESCRIPTION 1 1 A19142 SUB FRAME ASSEMBLY, 6 X SCREW, HX HD CAP, 3/4-16 12 5 100824 6, LOAD CELL, HYDRO, 9 UNF X 2 GR5 24 2 100556 WASHER, FLAT, 3/4 SIDE MOUNT PLATE, TRUCK 6 6 19207 MOUNT, 25 12 3 100252 NUT, HEX, 3/4-16 UNF GR5 PEDESTAL ASSEMBLY, 4 7 A8098 500,700,900 12 4 100554 WASHER, LOCK, 3/4 5 P age
SUB-FRAME GROUP HYDRO HD (900) & PARTS LIST NOTES: ITEMS (1, 2, 3, 4, 5, 6 & 7) ARE ALSO PART OF KIT A1917. BOLT SIDE MOUNT PLATES TO SUB-FRAME MOUNTS FOR LATER ASSEMBLY. QTY ITEM PART # DESCRIPTION QTY ITEM PART # DESCRIPTION 1 1 A21452 SUB FRAME ASSEMBLY, 6 X 6, SCREW, HX HD CAP, 3/4-16 8 5 100824 LOAD CELL, HYDRO, 900 UNF X 2 GR5 4 2 A8098 PEDESTAL ASSEMBLY, WASHER, LOCK, 3/4 8 6 100554 500,700,900 4 3 19207 SIDE MOUNT PLATE, TRUCK NUT, HEX, 3/4-16 UNF GR5 8 7 100252 MOUNT, 25 16 4 100556 WASHER, FLAT, 3/4 6 P age
900 SD HYDROSTATIC DRIVE COMPONENTS & PARTS LIST NOTES: NO PART NUMBER QTY ITEM PART # DESCRIPTION QTY ITEM PART # DESCRIPTION 1 1 103869 PLANETARY GEARBOX, SERIES OIL COOLER (DUAL FAN) 1 4 103181 300, 55.9:1, 1200 (OBSOLETE) 1 2 103193 HYDRAULIC PUMP, #90L130E FAN MOTOR,(3061020) 2 5 NPN 90L130(FEPTO) FRONT 1 2 103194 HYDRAULIC PUMP, #90R130 FAN BLADE (3070015) 2 6 NPN 90R130(REPTO) REAR HYDROSTATIC DRIVE MOTOR COOLER KIT, HYDAC 1 3 103195 51V110, Replaced by "104310 &104311E" 1 7 A1949 1 3 103197 HYDROSTATIC DRIVE MOTOR COOLER FAN & MOTOR, 1 8 68224 90R130 DUAL, SUPREME-A 7 P age
AUGER GROUP, 900 FEED EZ MIX (1/2 FLT) ASSEMBLY (A8255) NOTES: LINE ITEM #1 NOT USE TO DETERMINE FLIGHTING TYPE: COMPARE THE FLIGHTING WITH THE THREADS OF A BOLT AND IF THE FLIGHTING IS WRAPPED AROUND THE PIPE EXTENDING AWAY FROM YOU IN A CLOCKWISE DIRECTION THEN IT IS RIGHT HAND (RH) FLIGHTING IF THE FLIGHTING IS WRAPPED AROUND THE PIPE EXTENDING AWAY FROM YOU IN THE COUNTER CLOCKWISE DIRECTION THEN IT IS LEFT HAND (LH) FLIGHTING. BEARINGS: SEE REAR DRIVE NOTES: THESE ARE NOT ACTUAL FLIGHTING ARRANGEMENTS; THESE DRAWINGS ARE FOR ILLUSTRATION ONLY. PLEASE CHECK AUGER TUBE DIAMETER, ORIGINAL FLIGHTING SIZE, AND FLIGHTING ARRANGEMENT BEFORE ORDERING REPLACEMENT FLIGHTING. PLEASE SPECIFY AR OR MILD STEEL. SEE AUGER ORDER FORM. 8 P age
AUGER GROUP, 900 FEED EZ MIX (1/2 FLT) ASSEMBLY PARTS LIST QTY ITEM # PART # DESCRIPTION QTY ITEM # PART # DESCRIPTION 8 2 102558 BEARING, FB SFB1000NE, 3 STUB SHAFT ASSEMBLY,3 2 11 A18163 15/16 15/16OD X 8 3/8 LG 24 3 102559 SCREW, HX HD CAP, 7/8-14 AUGER ASSEMBLY, LOWER RH, 1 12 A21950 UNF X 3 GR5 EZ-MIX, 900 FEED 24 4 100361 WASHER, LOCK, 7/8 SCREW, HX HD CAP 3/4-16 35 13 100555 UNF X 2 1/2 GR5 24 5 100249 NUT, HEX 7/8-14 UNF GR5 33 14 100252 NUT, HEX, 3/4-16 UNF GR5 2 6 A18161 B SHAFT ASSEMBLY, 3 15/16 AUGER ASSEMBLY, LOWER LH, 1 15 A21951 OD X 8 3/8 LG, TAPPED EZ-MIX, 900 FEED 2 7 18164 STUB SHAFT SPACER, RING AUGER ASSEMBLY, UPPER RH, 1 16 A18143 5/16 X 4 1/2 OD, 900 900 FEED 2 8 18165 STUB SHAFT SPACER, WASHER 3/8 X 4 1/2 OD, 1 17 A18146 AUGER ASSEMBLY, UPPER LH, 900 FEED 900 37 9 100554 WASHER, LOCK, 3/4 2 18 A18154 STUB SHAFT ASSEMBLY, 3 2 10 101082 SCREW, HX HD CAP, 3/4-10 X 1 1/2 GR5 2 19 A16416 15/16 OD X 26 7/8 LG STUB SHAFT ASSEMBLY, 3 15/16 OD X 17 1/4 LG 9 P age
AUGER GROUP 900 SD FEED 4 15/16 SHAFTS (A8028) NOTES: ITEM NUMBER (8) IS NOT USED USE WITH: 1200 OIL BATH (4 15/16 BEARINGS) W/ NO UPPER BEARING SUPPORT W/ 1200 LOWER BEARING SUPPORT NOTES: ITEM #8 IS NOT USED 10 P age
AUGER GROUP 900 SD FEED 4 15/16 SHAFTS PARTS LIST QTY ITEM # PART # DESCRIPTION QTY ITEM # PART # DESCRIPTION 1 1 A18145 AUGER ASSEMBLY, LOWER RH, WASHER, SHAFT SPACER, 4 OD 2 14 15404 900 FEED X 3/8 1 2 A18144 AUGER ASSEMBLY, LOWER LH, SCREW, HX HD CAP, 3/4-10 X 1 2 15 101082 900 FEED 1/2 GR5 1 3 A18143 AUGER ASSEMBLY, UPPER RH, STUB SHAFT ASSEMBLY, LOWER, 2 16 A20068 900 FEED 1200 1 4 A18146 AUGER ASSEMBLY, UPPER LH, BEARING, FB SFB1000NE, 3 6 17 102558 900 FEED 15/16 2 5 A20027 STUB SHAFT ASSEMBLY, UPPER WASHER, LOCK, 7/8 20 18 100361 REAR, 900SD 2 6 A18163 STUB SHAFT ASSEMBLY,3 NUT, HEX 7/8-14 UNF GR5 24 19 100249 15/16OD X 8 3/8 LG 4 7 103822 SCREW, HX HD CAP, 7/8-14 X WASHER, LOCK, 7/8 24 20 100361 5 1/2 GR5 40 9 100555 SCREW, HX HD CAP 3/4-16 UNF BEARING, 4 15/16 BORE, 1200 2 21 103214 X 2 1/2 GR5 (ADAMS) 40 10 100252 NUT, HEX, 3/4-16 UNF GR5 REW, HX HD, 1 1/8-12 X 3 1/2 8 22 103399 GR8, 120 42 11 100554 WASHER, LOCK, 3/4 ADAPTER,6401-20-20, 20 O- 8 23 103400 RING{M} 1 1/4 NPT(M) 2 12 A18161 STUB SHAFT ASSEMBLY, 3 BALL VALVE (PARKER) 8 24 103401 15/16 OD X 8 3/8 LG, TAPPED 2 13 15403 STUB SHAFT SPACER, 4 1/8 OD BEARING SEAL ASSEMBLY, 4 2 25 A20275 X 3/8 LG 15/16 ID, 1200 (OPTIONAL) 11 P age
AUGER GROUP 900 SD FEED (3/4 FLT) 4 15/16 SHAFTS (A8170) USE WITH: 1200 OIL BATH (4 15/16 BEARINGS) W/ NO UPPER BEARING SUPPORT W/ 1200 LOWER BEARING SUPPORT NOTES: LINE ITEM NUMBER (8) IS NOT USED 12 P age
AUGER GROUP 900 SD FEED (3/4 FLT) 4 15/16 SHAFTS PARTS LIST QTY ITEM # PART # DESCRIPTION QTY ITEM # PART # DESCRIPTION 1 1 A18145 AUGER ASSEMBLY, LOWER RH, WASHER, SHAFT SPACER, 4 OD 2 14 15404 900 FEED X 3 1 2 A18144 AUGER ASSEMBLY, LOWER LH, SCREW, HX HD CAP, 3/4-10 X 1 2 15 101082 900 FEED 1/2 GR5 1 3 A18143 AUGER ASSEMBLY, UPPER RH, STUB SHAFT ASSEMBLY, LOWER, 2 16 A20068 900 FEED 1200 1 4 A18146 AUGER ASSEMBLY, UPPER LH, BEARING, FB SFB1000NE, 3 6 17 102558 900 FEED 15/16 2 5 A20027 STUB SHAFT ASSEMBLY, SCREW, HX HD CAP, 7/8-14 UNF 20 18 102559 UPPER REAR, 900SD X 3 GR5 2 6 A18163 STUB SHAFT ASSEMBLY,3 NUT, HEX 7/8-14 UNF GR5 24 19 100249 15/16OD X 8 3/8 LG 4 7 103822 SCREW, HX HD CAP, 7/8-14 X WASHER, LOCK, 7/8 24 20 100361 5 1/2 GR5 40 9 100555 SCREW, HX HD CAP 3/4-16 BEARING, 4 15/16 BORE, 1200 2 21 103214 UNF X 2 1/2 GR5 (ADAMS) 40 10 100252 NUT, HEX, 3/4-16 UNF GR5 SCREW, HX HD, 1 1/8-12 X 3 8 22 103399 1/2 GR8, 1200 42 11 100554 WASHER, LOCK, 3/4 ADAPTER,6401-20-20, 20 O- 8 23 103400 RING{M} 1 1/4 NPT(M) STUB SHAFT ASSEMBLY, 3 BALL VALVE (PARKER) 2 12 A18161 15/16 OD X 8 3/8 LG, TAPPED 8 24 103401 2 13 15403 STUB SHAFT SPACER, 4 1/8 BEARING SEAL ASSEMBLY, 4 2 25 A20275 OD X 3/8 LG 15/16 ID, 1200 (OPTIONAL) 13 P age
AUGER GROUP 900 FEED RH DISCHARGE, 16 (A8151) & PARTS LIST QTY ITEM # PART # DESCRIPTION QTY ITEM # PART # DESCRIPTION ~ ~ A8151 AUGER GROUP, RH DISCHARGE, STUB SHAFT SPACER, 4 1/8 OD 2 9 15403 2-AUGER, 3 15/16, 900 FEED X 3/8 LG 1 1 A21014 AUGER ASSEMBLY, LOWER RH WASHER, SHAFT SPACER, 4 OD 2 10 15404 DISCHARGE, 720 FEED X 3/8 1 2 A21015 AUGER ASSEMBLY, LOWER LH SCREW, HX HD CAP, 3/4-10 X 2 11 101082 DISCHARGE, 720 FEED 1 1/2 GR5 2 3 102455 BEARING, BLOCK, 3 7/16 STUB SHAFT ASSEMBLY, 3 2 12 A16416 FLANGE, SPHERICAL 15/16 OD X 17 1/4 LG 8 4 100825 SCREW, HX HD CAP, 3/4-16 UNF BEARING, FB SFB1000NE, 3 2 13 102558 X 3 GR 15/16 16 5 100555 SCREW, HX HD CAP 3/4-16 UNF X SCREW, HX HD CAP, 7/8-14 8 14 102559 2 1/2 GR5 UNF X 3 GR5 24 6 100252 NUT, HEX, 3/4-16 UNF GR5 8 15 100249 NUT, HEX 7/8-14 UNF GR5 26 7 100554 WASHER, LOCK, 3/4 8 16 100361 WASHER, LOCK, 7/8 2 8 A15590 STUB SHAFT ASSEMBLY, 3 7/16 OD X 7 3/4, TAPPED 14 P age
AUGER GROUP, 900 FEED EZ NO OUTBOARD (A8355) NOTES: ITEM # 1 IS NOT USED. 15 P age
AUGER GROUP, 900 FEED EZ NO OUTBOARD PARTS LIST QTY ITEM # PART # DESCRIPTION QTY ITEM # PART # DESCRIPTION ~ ~ A8355 AUGER GROUP, 900 FEED EZ STUB SHAFT ASSEMBLY, 3 7/16 2 11 A15590 OUTBOARD OD X 7 3/4, TAPPED 8 2 102558 BEARING, FB SFB1000NE, 3 AUGER ASS'Y, LOWER RHT 9-20 (8 1 12 A22529 15/16 5/8 TUBE 32 3 102559 SCREW, HX HD CAP, 7/8-14 UNF AUGER ASS'Y, LOWER LFT 9-20(8 1 13 A22528 X 3 GR5 5/8 TUBE) 32 4 100361 WASHER, LOCK, 7/8 AUGER ASSEMBLY, UPPER RH, 1 14 A18143 900 FEED 32 5 100249 NUT, HEX 7/8-14 UNF GR5 SCREW, HX HD CAP 3/4-16 UNF X 40 15 100555 2 1/2 GR5 2 6 A18161 STUB SHAFT ASSEMBLY, 3 15/16 NUT, HEX, 3/4-16 UNF GR5 40 16 100252 OD X 8 3/8 LG, TAPPED 2 7 18164 STUB SHAFT SPACER, RING 5/16 AUGER ASSEMBLY, UPPER LH, 900 1 17 A18146 X 4 1/2 OD, 900 FEED 2 8 18165 STUB SHAFT SPACER, WASHER STUB SHAFT ASSEMBLY, 3 15/16 2 18 A21495 3/8 X 4 1/2 OD, 900 OD X 20 7/8 LG 42 9 100554 WASHER, LOCK, 3/4 STUB SHAFT ASSEMBLY, 3 15/16 2 19 A16416 OD X 17 1/4 2 10 101082 SCREW, HX HD CAP, 3/4-10 X 1 1/2 GR5 16 P age
AUGER GROUP, 900SD RCL SPECIAL (A8393) NOTES: LINE ITEM #1, 2 ARE NOT USED. 17 P age
AUGER GROUP, 900SD RCL SPECIAL PARTS LIST QTY ITEM # PART # DESCRIPTION QTY ITEM # PART # DESCRIPTION 6 3 102558 BEARING, FB SFB1000NE, 3 AUGER ASSY, UPPER LEFT 1 14 A23353 15/16 900SD (RCL SPECIAL) 2 4 103214 BEARING, 4 15/16 BORE, 1200 AUGER ASSY, UPPER RIGHT 1 15 A23354 (ADAMS) 900SD (RCL SPECIAL) 4 5 A18161 STUB SHAFT ASSEMBLY, 3 SCREW, HX HD CAP, 7/8-14 20 16 102559 15/16 OD X 8 3/8 LG, TAPPED UNF X 3 GR5 2 6 A20068 STUB SHAFT ASSEMBLY, LOWER, WASHER, LOCK, 7/8 24 17 100361 1200 2 7 A20027 STUB SHAFT ASSEMBLY, UPPER NUT, HEX 7/8-14 UNF GR5 24 18 100249 REAR, 900SD 2 8 18164 STUB SHAFT SPACER, RING 5/16 SCREW, HX HD CAP, 7/8-14 X 4 19 103822 X 4 1/2 OD, 900 5 1/2 GR5 2 9 18165 STUB SHAFT SPACER, WASHER SCREW,HEX HD 1 1/4"-12X4 8 20 104436 3/8 X 4 1/2 OD, 900 GR8 42 10 100554 WASHER, LOCK, 3/4 WASHER, LOCK 1 1/4"- 8 21 104437 PLATED 2 11 101082 SCREW, HX HD CAP, 3/4-10 X 1 NUT, 1 1/4"- GR8 PLATED 8 22 104438 1/2 GR5 1 12 A23351 AUGER ASSY, LOWER LEFT SCREW, HX HD CAP 3/4-16 40 23 100555 900SD (RCL SPECIAL) UNF X 2 1/2 GR5 1 13 A23352 AUGER ASSY, LOWER RIGHT NUT, HEX, 3/4-16 UNF GR5 40 24 100252 900SD (RCL SPECIAL) 18 P age
REAR DRIVE GROUP 900 SD 4 15/16 BEARINGS & PARTS LIST (A8029) NOTES: GOTTSCH USES: 1200 OIL BATH (4 15/16) W/ NO UPPER BEARING SUPPORT W/ NO LOWER BEARING SUPPORT USE WITH: 1200 OIL BATH (4 15/16) W/ NO UPPER BEARING SUPPORT W/ 1200 LOWER BEARING SUPPORT QTY ITEM # PART # DESCRIPTION QTY ITEM # PART # DESCRIPTION 1 1 103868 PLANETARY GEARBOX, SERIES ROLLER CHAIN, #160HD X 1 9 103212 300, 33:1, 1200 69P, INCL CONN & OFFSET OPT 1 103208 PLANETARY GEARBOX, SERIES 400, 58.26:1, 1200 (ADAMS) 2 10 103206 SPROCKET, #160 CHAIN X 35 TEETH, 3 15/16 BORE, 1 KEY 2 2 A20068 STUB SHAFT ASSEMBLY, LOWER, KEY, SQUARE 1 X 10 1/2 1 11 20094 1200, SB-SW 2 3 A20027 STUB SHAFT ASSEMBLY, UPPER ROLLER CHAIN, #160HD X 1 12 103212 REAR, 900SD, SB 69P, INCL CONN & OFFSET 1 4 103362 SPROCKET, DS #160 CHAIN X SCREW, HX HD CAP, M14-2 X 30 14 103315 18 TEETH, 120MM BORE, 2 KEY 160MM, METRIC (ADAMS) 2 5 103490 ROLLER CHAIN, #160HD X 76P, SCREW, HX HD CAP 5/8-18 X 30 15 103314 INCL CONN 1 1/2 GR5 SPROCKET,#160 CHAIN X WASHER, LOCK, 5/8 2 6 103361 60TEETH,4 15/16 BORE W 1 1/4 KEY 30 16 100273 2 7 20141 KEY, SQUARE 1 1/4 X 10 1/2 1 17 20164 KEY SPACER 1 8 103205 SPROCKET, #160 CHAIN X 27 TEETH, 4 15/16 BORE W/ KEY 19 P age
REAR DRIVE GROUP 900 SD MIXER (3 15/16) BEARINGS (A8026) USE WITH: 1200 OIL BATH (3 15/16 BEARINGS) W/ NO UPPER BEARING SUPPORT W/ 900 LOWER BEARING SUPPORT (A18449) LINE ITEM # 12 & 13 ARE NOT USED. QTY ITEM # PART # DESCRIPTION QTY ITEM # PART # DESCRIPTION 1 1 103868 PLANETARY GEARBOX, SERIES SPROCKET, #120 CHAIN X 36 2 8 102805 300, 33:1, 1200 TEETH, 3 15/16 BORE OPT 1 103869 PLANETARY GEARBOX, SERIES CHAIN, #120 X 94P, INCL 2 9 102809TSU 300, 55.9:1, 1200 CONN (TSUBAKI) 2 2 A18154 STUB SHAFT ASSEMBLY, 3 SPROCKET, #120 CHAIN X 45 2 10 102806 15/16 OD X 26 7/8 LG TEETH, 3 15/16 BORE 2 3 A16416 STUB SHAFT ASSEMBLY, 3 KEY, SQUARE 1 X 5 1/2 2 11 17772 15/16 OD X 17 1/4 L 1 4 103362 SPROCKET, DS #160 CHAIN X 18 TEETH, 120MM BORE, 2 KEY 30 14 103315 SCREW, HX HD CAP, M14-2 X 160MM, METRIC (ADAMS) 2 5 103490 ROLLER CHAIN, #160HD X SCREW, HX HD CAP 5/8-18 X 30 15 103314 76P, INCL CONN 1 1/2 GR5 2 6 102804 SPROCKET, #160 CHAIN X 60 WASHER, LOCK, 5/8 30 16 100273 TEETH, 3 15/16 BORE 2 7 17782 KEY, SQUARE 1 X 8 1/2 1 17 20164 KEY SPACER, 4-B-12 20 P age
REAR DRIVE GROUP 900 SD (A8231) NOTES: INSTALL OIL WIPER ASSEMBLIES BEFORE INSTALLING SPROCKETS. ADJUST OILERS AS NEEDED. 21 P age
REAR DRIVE GROUP 900 SD PARTS LIST QTY ITEM # PART # DESCRIPTION QTY ITEM # PART # DESCRIPTION 1 1 A20095 OIL BATH ASSEMBLY, HEAVY DUTY 160 & 240 SPROCKET, 900SD 2 23 20142 KEY SPACER 1 2 103207 SPROCKET, #160 CHAIN X 24 ROLLER CHAIN, #160HD X 69P, 1 24 103212 TEETH, 4 15/16 BORE INCL CONN & OFFSET 2 3 103204 SPROCKET, #240 CHAIN X 40 ROLLER CHAIN, #160HD X 69P, 4 25 103213 TEETH, 1 1/4 KEYWAY INCL CONN & OFFSET 1 4 103205 SPROCKET, #160 CHAIN X 27 TEETH, 4 15/16 BORE W/ KEY 4 26 101840 EYE BOLT, 3/8-16UNC X 6 LG 2 5 20141 KEY, SQUARE 1 1/4 X 10 1/2 4 27 100254 NUT, HEX 3/8-16 UNC GR5 2 6 103206 SPROCKET, #160 CHAIN X 35 TEETH, 3 15/16 BORE, 1 KEY 4 28 7070514 CHAIN LOG, 3/16 GR30, PLATED 2 7 20150 KEY, SQUARE 1 X 10 1/2 4 29 101831 EXTENSION SPRING, 1 1/4 X 8 LG, #626 1 8 A21706 TENSIONER ARM ASSEMBLY W/ COMPRESSION FITTING, 1/8 12 30 102797 GUSSET NPT(F) X 1/4 X 90 1 9 A21012 IDLER ARM BAR ASSEMBLY 1 31 6060031-8029-1 GREASE LINE, UPPER RH, 900SD 1 10 18105 TENSIONER ARM BAR, 1 X 2 X 6060031-1 32 18 1/2 LG 8029-2 GREASE LINE, LOWER RH, 900SD 4 11 18108 TENSIONER SPACER BAR, UHMW 1 33 6060031-8029-3 GREASE LINE, UPPER LH, 900SD 1 12 18106 TENSIONER ANGLE, UHMW, 6060031-1 34 FORMED 8029-4 GREASE LINE, LOWER LH, 900SD 3 13 18107 TENSIONER COVER PLATE, LONG, UHMW 6 35 100218 GREASE FITTING, 1/8 NPT 2 14 18109 TENSIONER GUIDE, CHAIN #120, OUTBOARD BEARING SUPPORT 1 36 A20107 UMHW ASSEMBLY, LOWER, 1200 8 15 100694 SCREW, HX HD CAP, 3/8-16 UNC BEARING, FB SFB1000NE, 3 2 37 102558 X 2 1/2 GR2 15/16 8 16 101985 NUT, LOCK HEX 3/8-16 UNC GR5 8 38 100332 ELECTRIC PUMP, 4QT 1 17 A21010 TENSIONER ARM ASSEMBLY, 22 LG 8 39 100361 WASHER, LOCK, 7/8 4 18 102355 BEARING, 1 ID, NYLINER 8 40 100744 NUT, HEX, 7/8-9 UNC GR5 12 19 101829 SET SCREW, COLLAR, 1 ID X 1 6060031- GREASE LINE, RH OUTBOARD, 1 41 5/8 OD 8029-5 900SD 1 20 A20156 OIL WIPER ASSEMBLY 1 42 6060031- GREASE LINE, LH OUTBOARD, 8029-6 900SD 1 21 A18191 OIL WIPER ASSEMBLY W/ LONG 2 43 20151 IDLER ROLLER, 240 CHAIN 2 22 103203 END, 7 LG SPROCKET, #240 CHAIN X 12 TEETH, 2 KEYS, 120 APART 2 44 103209 ROLLER CHAIN, #240 X 49P, INCL CONN & OFFSET 22 P age
DISCHARGE GROUP, TRIPLE SHORT (NEW) (A8262) *- MEANS NOT SHOWN NOTES: THESE ITEMS (# 9, 10, 22, 23 & 24) ARE IN PARTS BAG #A7616 ALIGN BOTTOM OF LINKAGE MOUNT PLATE ASSEMBLY (ITEM #39) TO TOP OF DISCHARGE SIDE CENTERED IN SLOTS. 23 P age
DISCHARGE GROUP, TRIPLE SHORT (NEW) PARTS LIST QTY ITEM # PART # DESCRIPTION QTY ITEM # PART # DESCRIPTION 1 2 A22387 DROP CHUTE ASSEMBLY, TRIPLE, NEW {without magnets}w/rubbers 8 26 100443 WASHER, FLAT, 1/4, WROUGHT 1 3 A22384 DROP CHUTE CYLINDER SCREW, HX HD CAP 1/4-20 4 27 100858 ASSEMBLY, TRIPLE NEW UNC X 1 1 4 A21476 PIN ASSEMBLY, HEIGHT CONTROL 2 30 20936 DISCHARGE WING, SHIELD PLATE 1 5 A22203 PIN ASSEMBLY, 1 X 2 3/8 LG 16 32* 100713 WASHER, FLAT 5/16, USS- PLATED 1 6 100556 WASHER, FLAT, 3/4 16 33* 100170 WASHER, LOCK, 5/16 4 7 101018 HAIR PIN CLIP 16 34* 100297 NUT, HEX 5/16-18 UNC GR5 8 8 101716 SCREW, HX HD CAP, 3/8-16 UNC FLAT BAR, 1/4, RUBBER MAT 1 35* 21594 X 1 1/4 SUPPORT TRIPLE ONLY 25 9 100271 WASHER, LOCK, 3/8 4 36* 100304 WASHER, LOCK, 1/4 25 10 100254 NUT, HEX 3/8-16 UNC GR5 4 37* 100221 NUT, HEX 1/4-20 UNC GR5 2 11 100985 MAGNET, 8 X 18 1/2 LG 1 38 A21993 DISCHARGE ASSEMBLY, TRIPLE, SHORT, NEW STYLE 16 12 102283 SCREW, TRUSS HD, 5/16-18 UNC LINKAGE MOUNT PLATE 1 39 A22609 X 3/4 GR2 ASSEMBLY 1 16 21592 RUBBER MAT, DROP CHUTE DROP CHUTE LINKAGE 1 40 A23189 SPOUT, TRIPLE ASSEMBLY 9 17 104164 SCREW, CARRIAGE HD, 3/8-16 X SET SCREW, COLLAR, 1 ID X 2 41 101829 1 1/4 1 5/8 OD 2 18 21569 FLAT BAR, 1/4, SMALL SUPPORT 1 42 22795 LINKAGE, DROP CHUTE CYLINDER (SHORT) 2 20 21961 DISCHARGE HANGER, 5" HIGH PIN ASSEMBLY, 1"DIA. X 1 2 43 A23191 DOOR, SHORT 5/8" LG. 2 21 16078 SPACER BAR, 1/4 X 2 1/2 X 11 DROP CHUTE CYLINDER 1 44 22606 LG. MOUNT (BOLTED) 4 22 102096 SCREW, CARRIAGE HD, 3/8-16 SCREW, HX HD CAP, 1/2-13 2 45 103846 UNC X 1 GR5 UNC X 2 GR5 4 23 102621 SCREW, CARRIAGE HD, 3/8-16 UNC X 1 1/2 GR5 2 46 100838 WASHER, FLAT, 1/2 12 24 100300 WASHER, FLAT 3/8, USS 2 47 100272 WASHER, LOCK, 1/2 2 25 20935 DISCHARGE WING SHIELD 2 48 300826C NUT, HEX 1/2-13 UNC GR5 24 P age
DISCHARGE GROUP, TRIPLE MED (NEW) (A8279) NOTES: THESE ITEMS # (16, 17, 27, 28 & 29) ARE IN PARTS BAG #7616. ALIGN BOTTOM OF LINKAGE MOUNT PLATE ASSEMBLY (ITEM #32) TO TOP OF DISCHARGE SIDE CENTERED IN SLOTS. ****ITEMS # 3, 10, 24, 25, & 26. (ARE NOT SHOWN IN DRAWING)**** 25 P age
DISCHARGE GROUP, TRIPLE MED (NEW) PARTS LIST QTY ITEM # PART # DESCRIPTION QTY ITEM # PART # DESCRIPTION 1 1 A22387 DROP CHUTE ASSEMBLT, TRIPLE SCREW, CARRIAGE HD, 3/8-9 22 104164 16 X 1 1/4 1 2 A22384 DROP CHUTE CYLINDER SCREW, TRUSS HD, 5/16-18 16 23 102283 ASSEMBLY, NEW UNC X 3/4 GR2 1 4 A22384 DROP CHUTE CYLINDER WASHER, FLAT 5/16, USS- 16 24 100713 ASSEMBLY, NEW PLATED 1 5 100556 WASHER, FLAT, 3/4 16 25 100170 WASHER, LOCK, 5/16 4 6 101018 HAIR PIN CLIP 16 26 100297 NUT, HEX 5/16-18 UNC GR5 2 7 100985 MAGNET, 8 X 18 1/2 LG SCREW, CARRIAGE HD, 3/8-4 27 102096 16 UNC X 1 GR5 1 8 21592 DROP CHUTE SPOUT, RUBBER WASHER, FLAT 3/8, USS 12 28 100300 MAT, TRIPLE, SHORT 2 9 21592 DROP CHUTE SPOUT, RUBBER SCREW, CARRIAGE HD, 3/8-4 29 102621 MAT, TRIPLE, SHORT 16 UNC X 1 1/2 GR5 1 10 21594 FLAT BAR, 1/4, RUBBER MAT DISCHARGE ASSEMBLY, 1 30 A22135 SUPPORT TRIPLE ONLY TRIPLE, MEDIUM, NEW 2 11 20935 DISCHARGE WING SHIELD 1 31 A22203 PIN ASSEMBLY, 1 X 2 3/8 LG 2 12 20936 DISCHARGE WING, SHIELD PLATE LINKAGE MOUNT PLATE ASSY 1 32 A23222 MEDIUM 2 13 21962 DISCHARGE HANGER, 5" HIGH, DROP CHUTE LINKAGE 1 33 A23189 MEDIUM ASSEMBLY 2 14 16078 SPACER BAR, 1/4 X 2 1/2 X 11 LINKAGE, DROP CHUTE 1 34 22795 LG CYLINDER (SHORT) ASSY 8 15 101716 SCREW, HX HD CAP, 3/8-16 UNC COLLAR, SET SCREW 1 ID X 2 35 101829 X 1 1/4 1 5/8 OD 25 16 100271 WASHER, LOCK, 3/8 PIN ASSEMBLY, 1" DIA. X 1 2 36 A23191 5/8" LONG 25 17 100254 NUT, HEX 3/8-16 UNC GR5 DROP CHUTE CYL. MOUNT 1 37 22606 (BOLTED) 4 18 100858 SCREW, HX HD CAP 1/4-20 UNC SCREW, HX HD CAP, 1/2-13 2 38 103846 X 1 UNC X 2 GR5 4 19 100443 WASHER, FLAT, 1/4, WROUGHT 2 39 100838 WASHER, FLAT, 1/2 4 20 100304 WASHER, LOCK, 1/4 2 40 100272 WASHER, LOCK, 1/2 4 21 100221 NUT, HEX 1/4-20 UNC GR5 2 41 103795 NUT, HEX, 1/2-13 26 P age
DISCHARGE GROUP TRIPLE SHORT (33 ) (A7669) NOTES: BOLT ITEM 26 IN PLACE AT ASSEMBLY. CLOSE GAP, MATCH BOLT HOLE. ****ITEM # 10 (A20999) & ITEM # 26 (20935) IS OPTIONAL.**** 27 P age
DISCHARGE GROUP TRIPLE SHORT (33 ) PARTS LIST QTY ITEM # PART # DESCRIPTION QTY ITEM # PART # DESCRIPTION 1 1 A17902 DISCHARGE ASSEMBLY, TRIPLE DISCHARGE HANGER, SHORT, 2 13 19665 W/MOTOR, SHORT, 33" 300'S ONLY 1 2 A17370 CYLINDER ASSEMBLY, DROP CHUTE, 325-810 1 14 16078 SPACER BAR, 1/4 X 2 1/2 X 11 L 7 3 100240 SCREW, HX HD CAP, 3/8-16 X CYLINDER MOUNT HINGE TUBE, 1 1 15 14453 1 1/4 GR5 OD X 2 7/16 LG 7 4 100271 WASHER, LOCK, 3/8 1 16 14574 CYLINDER MOUNT BUSHING, 1 1/2 OD X 13/32 LG 7 5 100300 WASHER, FLAT 3/8, USS 1 17 14533 CYLINDER MOUNT PIN, 3/4 OD X 2 3/16 LG 7 6 100254 NUT, HEX 3/8-16 UNC GR5 2 18 101018 HAIR PIN CLIP 1 7 100796 SCREW, HX HD CAP, 1/2-20 UNF X 3 GR5 1 19 19669 DISCHARGE FILLER, TRIPLE 1 8 100838 WASHER, FLAT, 1/2 7 20 100323 SCREW, HX HD CAP, 1/4-20 UNC X 1 GR5 1 9 100272 WASHER, LOCK, 1/2 14 21 100443 WASHER, FLAT, 1/4, WROUGHT 1 10 A20999 DROP CHUTE ASSEMBLY, TRIPLE, SHORT, 500-720-810 7 22 100304 WASHER, LOCK, 1/4 1 10 A17916 DROP CHUTE HINGE ASSEMBLY, TRIPLE, 720,810 7 23 100221 NUT, HEX 1/4-20 UNC GR5 2 11 19546 DISCHARGE STOP STRAP, SHORT 1 24 A7616 DISCHARGE WING PARTS BAG 2 12 17958 DISCHARGE HANGER, SHORT 1 25 A20847 TENSIONER ARM ASSEMBLY 2 12 20987 DISCHARGE HANGER, SHORT, 400,500,70 2 26 20935 DISCHARGE WING SHIELD 2 27 20936 DISCHARGE WING, SHIELD PLATE 28 P age
DISCHARGE GROUP TRIPLE MED (40 ) (A7709) NOTES: BOLT ITME 26 IN PLACE AT ASSEMBLY CLOSE GAP, MATCH DRILL BOLT HOLE. **** ITEMS # 10 & 25 ARE OPTIONAL **** 29 P age
DISCHARGE GROUP TRIPLE MED (40 ) PARTS LIST QTY ITEM # PART # DESCRIPTION QTY ITEM # PART # DESCRIPTION 1 1 A18168 DISCHARGE ASSEMBLY SPACER BAR, 1/4 X 2 1/2 X 11 2 14 16078 W/MOTOR, TRIPLE, MED, 40" LG 1 2 A17370 CYLINDER ASSEMBLY, DROP CYLINDER MOUNT HINGE TUBE, 1 1 15 14453 CHUTE, 325-810 OD X 2 7/16 LG 7 3 100240 SCREW, HX HD CAP, 3/8-16 X 1 CYLINDER MOUNT BUSHING, 1 2 16 14574 1/4 GR5 1/2 OD X 13/32 LG 7 4 100271 WASHER, LOCK, 3/8 1 17 14533 CYLINDER MOUNT PIN, 3/4 OD X 2 3/16 LG 7 5 100300 WASHER, FLAT 3/8, USS 2 18 101018 HAIR PIN CLIP 7 6 100254 NUT, HEX 3/8-16 UNC GR5 1 19 19669 DISCHARGE FILLER, TRIPLE 1 7 100796 SCREW, HX HD CAP, 1/2-20 UNF SCREW, HX HD CAP, 1/4-20 UNC 7 20 100323 X 3 GR5 X 1 GR5 1 8 100838 WASHER, FLAT, 1/2 14 21 100443 WASHER, FLAT, 1/4, WROUGHT 1 9 100272 WASHER, LOCK, 1/2 7 22 100304 WASHER, LOCK, 1/4 1 10 A20999 DROP CHUTE ASSEMBLY, TRIPLE, SHORT, 500-720-810 7 23 100221 NUT, HEX 1/4-20 UNC GR5 1 10 A17916 DROP CHUTE HINGE ASSEMBLY, TRIPLE, 720,810 1 24 A7616 DISCHARGE WING PARTS BAG 2 11 19547 DISCHARGE STOP STRAP, MEDIUM 1 25 A20847 TENSIONER ARM ASSEMBLY 2 12 17958 DISCHARGE HANGER, SHORT 2 26 20935 DISCHARGE WING SHIELD 2 12 20987 DISCHARGE HANGER, SHORT, 400,500,700 2 27 20936 DISCHARGE WING, SHIELD PLATE 2 13 19665 DISCHARGE HANGER, SHORT, 300'S ONLY 30 P age
DISCHARGE GROUP TRIPLE EXTENDED (48 ) (A7710) NOTES: BOLT ITEM 26 IN PLACE AT ASSEMBLY CLOSE GAP. MATCH DRILL BOLT HOLE. ITEM # 10 & 25 ARE OPTIONAL. 31 P age
DISCHARGE GROUP TRIPLE EXTENDED (48 ) PARTS LIST QTY ITEM # PART # DESCRIPTION QTY ITEM # PART # DESCRIPTION 1 1 A18169 DISCHARGE ASSEMBLY SPACER BAR, 1/4 X 2 1/2 X W/MOTOR TRIPLE, EXTENDED, 2 14 16078 11 LG 48" 1 2 A17370 CYLINDER ASSEMBLY, DROP CYLINDER MOUNT HINGE TUBE, 1 15 14453 CHUTE, 325-810 1 OD X 2 7/16 LG 7 3 100240 SCREW, HX HD CAP, 3/8-16 X 1 CYLINDER MOUNT BUSHING, 1 2 16 14574 1/4 GR5 1/2 OD X 13/32 LG 7 4 100271 WASHER, LOCK, 3/8 1 17 14533 CYLINDER MOUNT PIN, 3/4 OD X 2 3/16 LG 7 5 100300 WASHER, FLAT 3/8, USS 2 18 101018 HAIR PIN CLIP 7 6 100254 NUT, HEX 3/8-16 UNC GR5 1 19 19669 DISCHARGE FILLER, TRIPLE 1 7 100796 SCREW, HX HD CAP, 1/2-20 UNF SCREW, HX HD CAP, 1/4-20 7 20 100323 X 3 GR5 UNC X 1 GR5 1 8 100838 WASHER, FLAT, 1/2 14 21 100443 WASHER, FLAT, 1/4, WROUGHT 1 9 100272 WASHER, LOCK, 1/2 17 22 100304 WASHER, LOCK, 1/4 1 10 A20999 DROP CHUTE ASSEMBLY, TRIPLE, SHORT, 500-720-810 7 23 100221 NUT, HEX 1/4-20 UNC GR5 1 10 A17916 DROP CHUTE HINGE ASSEMBLY, DISCHARGE WING PARTS BAG, 1 24 A8101 TRIPLE, 720,810 EXTENDED 2 11 19548 DISCHARGE STOP STRAP, EXTENDE 1 25 A20847 TENSIONER ARM ASSEMBLY 2 12 17998 DISCHARGE HANGER, EXT, 400'S-500'S-700'S 2 26 20935 DISCHARGE WING SHIELD 2 12 20989 DISCHARGE HANGER PLATE, DISCHARGE WING, SHIELD 2 27 20936 EXTENDED, 400,500,700 PLATE 2 13 19667 DISCHARGE HANGER, EXTENDED, 300 ONLY 32 P age
DISCHARGE GROUP TRIPLE DOUBLE SHORT (33 ) (A8020) NOTES: BOLT ITEM 25 IN PLACE AT ASSEMBLY CLOSE GAP. MATCH DRILL BOLT HOLE. ITEM # 10 (A20999) IS OPTIONAL. 33 P age
DISCHARGE GROUP TRIPLE DOUBLE SHORT (33 ) PARTS LIST QTY ITEM # PART # DESCRIPTION QTY ITEM # PART # DESCRIPTION 1 1 A20464 DISCHARGE ASSEMBLY, TRIPLE DISCHARGE HANGER, SHORT, 2 13 19665 DOUBLE, SHORT, 33" 300'S ONLY 2 2 A17370 CYLINDER ASSEMBLY, DROP SPACER BAR, 1/4 X 2 1/2 X 2 14 16078 CHUTE, 325-810 11 LG 7 3 100240 SCREW, HX HD CAP, 3/8-16 X 1 CYLINDER MOUNT HINGE 2 15 14453 1/4 GR5 TUBE, 1 OD X 2 7/16 LG 7 4 100271 WASHER, LOCK, 3/8 4 16 14574 CYLINDER MOUNT BUSHING, 1 1/2 OD X 13/32 LG 7 5 100300 WASHER, FLAT 3/8, USS 2 17 14533 CYLINDER MOUNT PIN, 3/4 OD X 2 3/16 LG 7 6 100254 NUT, HEX 3/8-16 UNC GR5 4 18 101018 HAIR PIN CLIP 2 7 100796 SCREW, HX HD CAP, 1/2-20 UNF X 3 GR5 1 19 19669 DISCHARGE FILLER, TRIPLE 2 8 100838 WASHER, FLAT, 1/2 7 20 100323 SCREW, HX HD CAP, 1/4-20 UNC X 1 GR5 2 9 100272 WASHER, LOCK, 1/2 14 21 100443 WASHER, FLAT, 1/4, WROUGHT 1 10 A20999 DROP CHUTE ASSEMBLY, TRIPLE, SHORT, 500-720-810 7 22 100304 WASHER, LOCK, 1/4 1 10 A19506 DROP CHUTE HINGE ASSEMBLY, TRIPLE, DUAL CYLINDERS 7 23 100221 NUT, HEX 1/4-20 UNC GR5 2 11 19546 DISCHARGE STOP STRAP, DISCHARGE WING PARTS 1 24 A7616 SHORT BAG 2 12 17958 DISCHARGE HANGER, SHORT 2 25 20935 DISCHARGE WING SHIELD 2 12 20987 DISCHARGE HANGER, SHORT, DISCHARGE WING, SHIELD 2 26 20936 400,500,700 PLATE 34 P age
RH DISCHARGE GROUP TRIPLE SHORT (33 ) (A8021) NOTES: BOLT TEM 25 IN PLACE AT ASSEMBLY CLOSE GAP, MATCH DRILL BOLT HOLE. 35 P age
RH DISCHARGE GROUP TRIPLE SHORT (33 ) PARTS LIST QTY ITEM # PART # DESCRIPTION QTY ITEM # PART # DESCRIPTION 1 1 A19864 DISCHARGE ASSEMBLY, RH, SPACER BAR, 1/4 X 2 1/2 X 11 2 14 16078 TRIPLE, SHORT, 33" LG 1 2 A17370 CYLINDER ASSEMBLY, DROP CYLINDER MOUNT HINGE TUBE, 1 1 15 14453 CHUTE, 325-810 OD X 2 7/16 LG 7 3 100240 SCREW, HX HD CAP, 3/8-16 X 1 CYLINDER MOUNT BUSHING, 1 2 16 14574 1/4 GR5 1/2 OD X 13/32 LG 7 4 100271 WASHER, LOCK, 3/8 1 17 14533 CYLINDER MOUNT PIN, 3/4 OD X 2 3/16 LG 7 5 100300 WASHER, FLAT 3/8, USS 2 18 101018 HAIR PIN CLIP 7 6 100254 NUT, HEX 3/8-16 UNC GR5 1 19 19669 DISCHARGE FILLER, TRIPLE 1 7 100796 SCREW, HX HD CAP, 1/2-20 UNF SCREW, HX HD CAP, 1/4-20 UNC 7 20 100323 X 3 GR5 X 1 GR5 1 8 100838 WASHER, FLAT, 1/2 14 21 100443 WASHER, FLAT, 1/4, WROUGHT 1 9 100272 WASHER, LOCK, 1/2 2 22 100304 WASHER, LOCK, 1/4 1 10 A19889 DROP CHUTE ASSEMBLY, RH, TRIPLE 7 23 100221 NUT, HEX 1/4-20 UNC GR5 2 11 19546 DISCHARGE STOP STRAP, SHORT 1 24 A7616 DISCHARGE WING PARTS BAG 2 12 17958 DISCHARGE HANGER, SHORT 2 25 20935 DISCHARGE WING SHIELD 2 13 19665 DISCHARGE HANGER, SHORT, 300'S ONLY 2 26 20936 DISCHARGE WING, SHIELD PLATE 36 P age
DOOR GROUP, OIL BATH 900SD, 1200 (A8034) NOTES: DOOR PIECE. ITEM # 13 TO BE USED ON TOP, SIDES AND BOTTOM OF DOOR OPENING. START AT THE TOP OPENING IN CENTER AND INSTALL SEAL ALL THE WAY AROUND OPENING. SHOULD BE ONE WELD DOOR MOUNT IN PLACE WHEN DOOR LOCATION IS SET. QTY ITEM # PART # DESCRIPTION QTY ITEM # PART # DESCRIPTION 1 1 20124 OIL BATH DOOR, 900SD,1200 36 12 100221 NUT, HEX 1/4-20 UNC GR5 1 2 18446 DOOR CHANNEL, RH, 1 X 7 X 57 5/8 LG, FORMED 26 13 102477 FLEXIBLE DOOR SEAL, 1/8 1 3 18445 DOOR CHANNEL, LH, 1 X 7 X 57 5/8 SCREW, HX SOCKET FLAT 16 14 102781 LG, FORMED HD, 1/4-20 X 1 1/4 1 4 20125 DOOR FRAME PLATE, 10GA X 4 X 53 GAS CHARGED SUPPORT 4 15 102451 1/2 LG, 900SD,1200 LIFT 3 5 102446 HINGE, BUTT, 4 X 4 4 16 100692 SCREW, HX HD CAP, 3/8-16 UNC X 1 1/2 GR5 3 6 17026 HINGE BACK PLATE, 1 1/2 X 4 LG, NUT, LOCK HEX 3/8-16 UNC 4 17 101985 630-810 GR5 10 7 19282 DOOR LATCH EXTENSION 8 18 100300 WASHER, FLAT 3/8, USS 2 8 102779 OIL BATH DOOR HANDLE 4 19 100254 NUT, HEX 3/8-16 UNC GR5 20 9 100323 SCREW, HX HD CAP, 1/4-20 UNC X UPPER STRUT MOUNT PLATE, 2 20 18244 1 GR5 1/4 X 7 1/2 X 18 3/8 LG 32 10 100443 WASHER, FLAT, 1/4, WROUGH 2 21 18236 STRUT MOUNT BRACE BAR, 1/4 X 1 1/2 X 19 LG 36 11 100304 WASHER, LOCK, 1/4 2 22 20786 DOOR STRUT ANGLE, 1 1/2 X 1 1/2 X 20 1/2 LG, 900 37 P age
TUB GROUP, 900 SD TRIPLE DISCHARGE (A8030) & PARTS LIST QTY ITEM # PART # DESCRIPTION QTY ITEM # PART # DESCRIPTION 1 1 A18029 SIDE ASSEMBLY, RH, 900 1 8 17913 PRESSURE BRACE PLATE, 1/4 X 11 X 53 1/2 LG, 720,810 1 2 A18030 SIDE ASSEMBLY, LH, LH TRIPLE, 900 1 9 100536 D-RING, 1 1/2 1 3 A18024 FRONT END SHEET ASSEMBLY, LINER, SS, SIDE, 60 X 72 LG, 630-8 11 19486 900 900 1 4 A20095-A OIL BATH ASSEMBLY, 4 15/16 SIDE STIFFENER, 1/4 X 10 X 71 3/4 2 12 19180 BEARING, DETAIL, 900SD LG, 500-700'S 4 5 A18861 LOAD CELL BRACKET ASSEMBLY, SIDE STIFFENER, 1/4 X 10 X 95 3/4 1 13 19181 WELDMENT, MM LG, 500-700'S 4 6 15002 AUGER BOTTOM, 15 1/2 RAD X 72 L 2 14 19228 LINER, SS, FRONT & REAR END, 900 2 7 15001 AUGER BOTTOM, 15 1/2 RAD X 96 LG, 502-720 1 15 A20827 COOLER BRACKET ASSEMBLY 38 P age
TUB GROUP, 900 SD TRIPLE DISCHARGE (A8105) & PARTS LIST NOTES: ITEM # 15 AND 16 OPTIONAL FOR HYDROSTATIC DRIVE MIXER ONLY. QTY ITEM # PART # DESCRIPTION QTY ITEM # PART # DESCRIPTION ~ ~ A8105 TUB GROUP, TRIPLE, LH PRESSURE BRACE PLATE, 1/4 X 1 8 17913 DISCHARGE, 3 15/16, 900SD 11 X 53 1/2 LG, 720,810 1 1 A18029 SIDE ASSEMBLY, RH, 900 1 9 100536 D-RING, 1 1/2 1 2 A18030 SIDE ASSEMBLY, LH, LH TRIPLE, LINER, SS, SIDE, 60 X 72 LG, 8 11 19486 900 630-900 1 3 A18024 FRONT END SHEET ASSEMBLY, 900 2 12 19180 SIDE STIFFENER, 1/4 X 10 X 71 3/4 LG, 500-700'S 1 4 A20487 OIL BATH ASSEMBLY, 3 15/16 SIDE STIFFENER, 1/4 X 10 X 95 1 13 19181 BEARING, 900SD 3/4 LG, 500-700'S 4 5 A18861 LOAD CELL BRACKET ASSEMBLY, LINER, SS, FRONT & REAR END, 2 14 19228 WELDMENT, MM 90 4 6 15002 AUGER BOTTOM, 15 1/2 RAD X 72 COOLER BRACKET ASSEMBLY, 1 15 A19502 LG LH, HYDRO 1 16 A19501 COOLER BRACKET ASSEMBLY, RH, HYDRO 39 P age