Constant Current & Constant Voltage LED Power Supply Product description This series was designed for compromise between an attractive price and high performance, which meets SELV standard of preventing electric shock. Protection of open circuit, short circuit, over load and over temperature increased safety in processing. Low standby power consumption complies with ERP directives. Optimized electric circuit design brings cost-effectiveness. Standards: Characteristics: EN61347-1 EN61347-2-13 EN61547 EN015 EN61000-3-2 EN61000-3-3 EN62384 UL80 UL1310 Universal input voltage(vac) Compact dimensions Independent use design Compatible with constant current and costant voltage function( and model) SELV output(<v) Class 2 output Low output ripple current ±15% Fast start-up time s No load power consumption 0.3W Open circuit,short circuit,over load and over temperature protection Auto restart after fault conditions removal High efficiency 79%(AC230V,full load) ECO design, comply with ERP directives Page: 1 of 6
Specifications Model SLT6-3IL-4 SLT6-0IL-4 SLT6-0IL-4 turn on time(s) Output output current(ma) CC CV output current tolerance ripple current(ma) working voltage range(v) Max. output voltage(v) output votage (V) output voltage tolerance ripple voltage(mv) working current range(a) 1 1 3 (Ip-p) 3-22 24 24 +/-1.5% 0(Vp-p) 0-0.3 0 (Ip-p) 3-14 0 90(Ip-p) 3-8.4 +/-1.5% 0(Vp-p) 0-0.5 dimming interface No dimming range rated supply voltage(vac) voltage range(vac) line frequency(hz) input current(ma) 0 0 0 Input efficiency 2 76.5%.0%.0% power factor 2 inrush current(ipk) over voltage protection short circuit protection Protection over temperature protection automatic restart over load protection surge capacity Ta( ) -20 +(3/); 40() Ambient and Life Tc max.( ) Storage Temperature( ) ambient humidity range (3/); () -30... 5%...%RH Not condensing nominal life-time(hrs) 35'000@Tc= weight(g) 37.5 dimensions (L W H)(mm) 68 35 20 Other casing material housing colour Plastic White type of protection IP20 protection class CLASS II Note 1. Tolerance:includes set up tolerance, line regulation and load regulation. 2. Tested at full load,230vac.refer to"power Factor" and "EFFICIENT"curve graphs. 3. All parameters NOT specially mentioned are measured at nominal voltage input, rated load and 25 of ambient temperature. 4. The power supply is considered as a component that will be operated in combination with final equipment. Since EMC performance will be affected by the complete installation, the final equipment manufacturers must re-qualify EMC Directive on the complete installation again." Page: 2 of 6
Dimensions(mm/inches): 35 20 58 64 68 Wiring diagram: VAC Hz N L LED POWER SUPPLY wire preparation 7-8mm 0.5-0. Page: 3 of 6
Electrical curves: 0. vs ( 230Vac) EFFICIENCY vs (230 Vac) 0. 0. 0. 30% 40% % % % % 90% 100% 30% 40% % % % % 90% 100 % vs (230Vac) 0. 0. 0. 0. 0. 0. 0. 0. 45 0.40 0. 35 0. 30 0. 25 0.20 10% 20% 30% 40% % % % % 90% 100 % V 45 EFFICIENCY vs (230Vac) 10% 20% 30% 40% % % % % 90% 100 % V Page: 4 of 6
Electrical curves: 0.90 vs (0Vac) EFFICIENCY vs (0Vac) 0. 0. 0. 30 % 40% % % % % 90 % 100% 30% 40% % % % % 90% 100% 0. 90 0. 0. 0. 0. 0. 0. 0. vs (0Vac) 10% 20% 30% 40% % % % % 90% 100% V EFFICIENCY vs (0Vac) 10% 20% 30% 40% % % % % 90% 100% V note For constant current power supply,"" means the percentage of the maximum rated output voltage. For constant voltage power supply,"" means the percentage of the maximum rated output current. Page: 5 of 6