Test Report issued under the responsibility of: TEST REORT LED modules for general lighting Safety specifications Report Number...: 2173700.50 Date of issue... : 20140923 Total number of pages... 33 Applicant s name...: Xicato Address... : 101 Daggett Drive, San Jose CA 95134 United States of America Test specification: Standard... : (First Edition):2008 + A1:2012 Test procedure...: CB Scheme Nonstandard test method..: Test Report Form No... : IEC62031B Test Report Form(s) Originator... : Intertek Semko AB Master TRF... : 201310 Copyright 2013 Worldwide System for Conformity Testing and Certification of Electrotechnical Equipment and Components (IECEE), Geneva, Switzerland. All rights reserved. This publication may be reproduced in whole or in part for noncommercial purposes as long as the IECEE is acknowledged as copyright owner and source of the material. IECEE takes no responsibility for and will not assume liability for damages resulting from the reader's interpretation of the reproduced material due to its placement and context. If this Test Report Form is used by noniecee members, the IECEE/IEC logo and the reference to the CB Scheme procedure shall be removed. This report is not valid as a CB Test Report unless signed by an approved CB Testing Laboratory and appended to a CB Test Certificate issued by an NCB in accordance with IECEE 02. Test item description... : LED module for builtin Trade Mark... : Xicato Manufacturer... : 101 Daggett Drive, San Jose CA 95134, United States of America Model/Type reference... : XIM series (XIMCC, XIMCV ) (010V / DALI) Ratings... : max.1,10 A dc, max. colour temp 3000K & 4000K
age 2 of 33 Testing procedure and testing location: CB Testing Laboratory: DEKRA Certification B.V. Testing location/ address...: Meander 1051, 6825 MJ Arnhem, The Netherlands Associated CB Laboratory: Testing location/ address...: Tested by (name + signature)... : J.H. Rikkers n E Approved by (+ signature)... : A.. van der Veen Testing procedure: TM Testing location/ address...: Tested by (name + signature)... : Approved by (+ signature)... : Testing procedure: WMT Testing location/ address...: Tested by (name + signature)... : Witnessed by (+ signature)... : Approved by (+ signature)... : Testing procedure: SMT Testing location/ address...: Tested by (name + signature)... : Approved by (+ signature)... : Supervised by (+ signature)... :
age 3 of 33 List of Attachments (including a total number of pages in each attachment): Summary of testing: Tests performed (name of test and test clause): Full type test according to EN /. Annex 1: Component list Annex 2: Temperature measurement results. Testing location: DEKRA Certification B.V Meander 1051, 6825 MJ Arnhem The Netherlands hotobiological testing according to IEC/EN 62471 Summary of compliance with National Differences: List of countries addressed: The product fulfils the requirements of. (insert standard number and edition and delete the text in parenthesis or delete the whole sentence if not applicable) Copy of marking plate The artwork below may be only a draft. The use of certification marks on a product must be authorized by the respective NCBs that own these marks. Marking plate dimmable version
age 4 of 33 Test item particulars... : Classification of installation and use... : Integral LED module Supply Connection... : With leads ossible test case verdicts: test case does not apply to the test object... : test object does meet the requirement... : (ass) test object does not meet the requirement... : F (Fail) Testing... : Date of receipt of test item... : 201408 Date (s) of performance of tests... : 20140825 20140909 General remarks: The test results presented in this report relate only to the object tested. This report shall not be reproduced, except in full, without the written approval of the Issuing testing laboratory. "(See Enclosure #)" refers to additional information appended to the report. "(See appended table)" refers to a table appended to the report. Throughout this report a comma / point is used as the decimal separator. numbers between brackets refer to clauses in IEC 613471 This report is based on Test Report No. 2170119.50, dated: 20140403. The following update was made: Adding of XIMVC models, 4000K version (010V or DALI). This report replaces Test Report No. 2170119.50. Manufacturer s Declaration per subclause 4.2.5 of IECEE 02: The application for obtaining a CB Test Certificate includes more than one factory location and a declaration from the Manufacturer stating that the sample(s) submitted for evaluation is (are) representative of the products from each factory has been provided... : Yes Not applicable When differences exist; they shall be identified in the General product information section. Name and address of factory (ies)... : Xicato 101 Daggett Drive, San Jose CA 95134 United States Of America
age 5 of 33 General product information: XIM series (XIMCC, XIMCV ): 1,10 Adc max Available in 400 lm, 700 lm, 1000 lm, 1300 lm, 2000 lm and 3000 lm. Colour temp 3000K & 4000K XIMCV series are dimmable (010V or DALI). These products are placed in: Risk group 1 (not labelling required). Intended for use: The customer is obligated to provide appropriate cooling as specified by tcase. The LED module must be isolated from metal housing of a luminaire and protected against touching when powered by a nonisolated (or basic isolated) driver. The LED module can only be used nonprotected if powered by a SELV LED driver. Tested sample XM 19803030CCA is representative for dimmable version.
age 6 of 33 4 GENERAL REQUIREMENTS 4.4 Integral modules tested assembled in the luminaire 4.5 Independent modules complies with requirements in IEC 605981 5 GENERAL TEST REQUIREMENTS 5.5 SELVoperated LED modules comply with Annex (see Annex 1) I of IEC 61347213 General conditions for tests in Annex A 6 Result Remark (see Annex A) CLASSIFICATION Builtin module...: Yes No Independent module...: Yes No Integral module...: Yes No For Integral module; Note to 1.2.1 in IEC 605981 applies. 7 MARKING 7.1 Mandatory markings a) mark of origin b) model number, type reference c1) constant voltage module; rated supply voltage and supply frequency c2) constant current module; rated supply current and supply frequency d) nominal power e) indication of connections, wiring diagram f) value of tc and place on the module g) eye protection h) symbol for builtin modules i) heat transfer temperature td j) power for heatconduction d k) working voltage for insulation
age 7 of 33 7.2 Location of marking Result Remark marking of a), b), c) and f) marking of d), e), g), h), i) and j) marking of k) integral modules a) to g) in literature 7.3 8 Durable and legibility of marking marking of a), b), c) and f) legible after test with water marking of d) to j) inspection of compliance TERMINALS Screw terminals according section 14 of IEC 605981: Separately approved; component list (see Annex 2) art of the luminaire (see Annex 3) Screwless terminals according section 15 of IEC 605981: Separately approved; component list (see Annex 2) art of the luminaire (see Annex 4) Connectors according IEC 6083822: Separately approved; component list (see Annex 2) 9 (9) ROVISION FOR ROTECTIVE EARTHING (9.1) rovisions for protective earthing Terminal complying with clause 8 Locked against loosening and not possible to loosen by hand Not possible to loosen clamping means unintentionally on screwless terminals Earthing via means of fixing Earthing terminal only used for the earthing of the control gear All parts of material minimizing the danger of electrolytic corrosion Made of brass or equivalent material Contact surface bare metal
age 8 of 33 (9.2) rovision for functional earthing Comply with clause 8 and 9.1 Earth contact via the track on the printed board Test with a current of 25 A between earthing terminal and each of the accessible metal parts; measured resistance ( ) at 10 A according 7.2.3 of IEC 605981: < 0,5...: Earthing of builtin lamp controlgear Earth by means of fixing to earthed metal of luminaire in compliance of 7.2 of IEC 605981 Earthing terminal only for earthing the builtin controlgear (9.5) Earthing via independent controlgear (9.5.1) Earth connection to other equipment Looping or through connection, conductor min. 1,5 mm² and of copper or equivalent rotective earthing wires in line with 5.3.1.1 and clause 7 Earthing of the lamp compartments powered via the independent lamp controlgear Test with a current of 25 A between input and output earth terminals; measured resistance ( ) between earthing terminal and each of the accessible metal parts at 10 A according 7.2.3 of IEC 605981: < 0,5...: Output earthing terminal marked as in 7.1 t) of IEC 613471 (9.3) (9.4) (9.5.2) Result Remark 10 (10) ROTECTION AGAINST ACCIDENTAL CONTACT WITH LIVE ARTS (10.1) Controlgear protected against accidental contact with live parts (A2) The current flowing between the part concerned and earth is measured and does not exceed 0,7 ma (peak) or 2 ma d.c....: (A2) For frequencies above 1 khz, the current does not exceed 0,7 ma (peak) multiplied by the value of the frequency in kilohertz or 70 ma (peak)...:
age 9 of 33 (A3) The voltage between the part concerned and any accessible part is measured and does not exceed 34 V (peak)...: (10.1) Lacquer or enamel not used for protection or insulation Adequate mechanical strength on parts providing protection (10.2) Capacitors > 0,5 F: voltage after 1 min (V): < 50 V...: (10.3) Controlgear providing SELV Accessible conductive parts are insulated from live parts by double or reinforced insulation in SELV controlgear No connection between output circuit and the body or protective earthing circuit No possibility of connection between output circuit and the body or protective earthing circuit through other conductive parts SELV outputs separated by at least basic insulation ELV conductive parts insulated as live parts Tests according Annex L of IEC 613471 Accessible conductive parts in SELV circuits Output voltage under load 25 V r.m.s. or 60 V d.c. If output voltage > 25 V r.m.s. or > 60 V d.c.; (10.4) Result Remark No load output 35 V peak or 60 V d.c and touch current does not exceed 0,7 ma (peak) or 2 ma d.c.... : One conductive part is insulated if output voltage or current exceeding the values above and withstand test voltage 500 V Double or reinforced insulation bridged by appropriate and at least two resistors or two Y2 capacitors or one Y1 capacitor Y1 or Y2 capacitors comply with IEC 6038414 Resistors comply with test (a) in 14.1 of IEC 60065
age 10 of 33 11 (11) MOISTURE RESISTANCE AND INSULATION After storage 48 h at 9195% relative humidity and 2030 C measuring of insulation resistance with d.c. 500 V (M ): For basic insulation 2 M...: > 50 MΩ 12 (12) Result Remark For double or reinforced insulation 4 M...: Between primary and secondary circuits in controlgear providing SELV, values in Annex L in IEC 613471 ELECTRIC STRENGTH Immediately after clause 11 electric strength test for 1 min Basic insulation for SELV, test voltage 500 V Working voltage 50 V, test voltage 500 V Working voltage > 50 V 1000 V, test voltage (V): Basic insulation, 2U + 1000 V Supplementary insulation, 2U + 1000 V Double or reinforced insulation, 4U + 2000 V No flashover or breakdown Solid or thin sheet insulation for double or reinforced insulation fulfil the requirements in Annex N in IEC 613471 13 (14) FAULT CONDITIONS (14) When operated under fault conditions the controlgear: does not emit flames or molten material does not produce flammable gases protection against accidental contact not impaired Thermally protected controlgear does not exceed the marked temperature value Fault conditions: capacitors, resistors or inductors (see appended table) without proof of compliance with relevant specifications have been shortcircuited or disconnected
age 11 of 33 Result Remark (14.1) Shortcircuit of creepage distances and clearances if less than specified in clause 16 in art 1 (except between live parts and accessible metal parts) (see appended table) Creepage distances on printed boards less than specified in clause 16 in art 1 provided with coating according to IEC 606643 (14.2) Shortcircuit or interruption of semiconductor devices (see appended table) (14.3) Shortcircuit across insulation consisting of lacquer, enamel or textile (see appended table) (14.4) Shortcircuit across electrolytic capacitors (see appended table) (14.5) After the tests has been carried out on three samples: The insulation resistance 1 M...: > 50MΩ No flammable gases No accessible parts have become live During the tests, a fivelayer tissue paper, where the test specimen is wrapped, does not ignite (14.6) Relevant fault condition tests with highpower supply 13.2 Module withstands overpower condition >15 min. Module with automatic protective device or power limiter, test performed 15 min. at limit. 15 16 During the tests, tissue paper, spread below module, does not ignite CONSTRUCTION Wood, cotton, silk, paper and similar fibrous material not used as insulation CREEAGE DISTANCES AND CLEARANCES Creepage and distances and clearances in compliance with IEC 605981 Working voltage (V)... : < 40 V Voltage form Sinusoidal Nonsinusoidal TI < 600 > 600
age 12 of 33 Result Remark Impulse withstand category (Normal category II) (Category III Annex U) Category II Category III Rated pulse voltage (kv)... : cr > 1,2 mm cl > 0,2 mm (2) Currentcarrying parts and accessible parts: cr cr > 1,2 mm (mm); cl (mm)... : cl > 0,2 mm (1) Currentcarrying parts of different polarity: cr (mm); cl (mm) : (3) arts becoming live due to breakdown of basic insulation and metal parts: cr (mm); cl (mm)... : (4) Outer surface of cable where it is clamped and metal parts: cr (mm); cl (mm)... : (6) Currentcarrying parts and supporting surface: cr > 1,2 mm cr (mm); cl (mm)... : cl > 0,2 mm SCREWS, CURRENTCARRYING ARTS AND CONNECTIONS Screws, currentcarrying parts and connections in compliance with IEC 605981 (clause numbers between parentheses refer to IEC 605981) (4.11) Electrical connections (4.11.1) Contact pressure (4.11.2) Screws: 17 (17) selftapping screws threadcutting screws (4.11.3) Screw locking: spring washer rivets (4.11.4) Material of currentcarrying parts (4.11.5) No contact to wood or mounting surface (4.11.6) Electromechanical contact systems (4.12) Mechanical connections and glands (4.12.1) Screws not made of soft metal Screws of insulating material
age 13 of 33 Result Remark Torque test: torque (Nm); part... : Torque test: torque (Nm); part... : Torque test: torque (Nm); part... : (4.12.2) Screws with diameter < 3 mm screwed into metal (4.12.4) Locked connections: fixed arms; torque (Nm)... : lampholder; torque (Nm)... : pushbutton switches; torque 0,8 Nm... : (4.12.5) Screwed glands; force (Nm)... : 18 (18) RESISTANCE TO HEAT, FIRE AND TRACKING Resistance to Heat, Fire and Tracking in compliance with IEC 613471 (clause numbers between parentheses refer to IEC 613471) (18.1) (18.2) (18.3) (18.4) (18.5) Ballpressure test: part tested; temperature ( C)... : part tested; temperature ( C)... : Test of printed boards part tested... : part tested... : Glowwire test (650 C): part tested... : Cover part tested... : Needle flame test (10 s): part tested... : part tested... : Tracking test: part tested... : part tested... :
age 14 of 33 19 (19) RESISTANCE TO CORROSION Rust protection: test according 4.18.1 of IEC 605981 adequate varnish on the outer surface INFORMATION FOR LUMINAIRE DESIGN 20 Result Remark Information in Annex D 21 HEAT MANAGEMENT 21.1 General Exchangeability is safeguarded by cap or base Heatconducting foil and paste Heatconducting foil delivered with the module if necessary Construction Electrical connection and mechanical holding are separate 21.2 21.4 14 TABLE: tests of fault conditions art Simulated fault LED Open NO Short circuited NO A Hazard ANNEX A TESTS All tests performed in accordance with the advice given in Annex H of IEC 613471, if applicable
age 15 of 33 Result Remark ANNEX 1: SELVoperated LED modules ANNEX I of IEC 61347213: I.3 Classification I.3.1 Class I Yes No Class II Yes No a) noninherently short circuit proof controlgear Yes No b) noninherently open circuit proof controlgear Yes No c) inherently short circuit proof controlgear Yes No d) inherently open circuit proof controlgear Yes No e) fail safe controlgear Yes No f) nonshortcircuit proof controlgear Yes No g) nonopencircuit proof controlgear Yes No I.3.2 I.4 Marking Adequate symbols are used I.5 rotection against electric shock I.5.1 No connection between output winding and body No connection between output winding and protective earthing circuit I.5.2 Input and output circuits electrically separated from each other I.5.2.1 Insulation between input and output winding of the HFtransformer consists of double or reinforced insulation Class II: insulation between input/output and body consists of double or reinforced insulation Class I: insulation between input and body consists of basic and between output and body supplementary insulation Insulation between input and output winding via the core consists of double or reinforced insulation Insulation between cord and windings of the HDtransformer consists of basic insulation Serrated tape, additional layer I.5.2.2 I.5.2.3
age 16 of 33 I.5.2.4 Class I controlgear for fixed connection provided with basic insulation plus protective screening comply with the following conditions: a) Insulation between the input winding and the protective screen complies with the requirements for basic insulation b) Insulation between the protective screen and the output winding complies with the requirements for basic insulation c)metal screen consists of a metal foil or of a wire wound screen d) Metal screen so arranged that both edges cannot simultaneously touch a magnetic core e) Metal screen and its leadout wire have a crosssection sufficient to ensure that an overload device will open the circuit before the screen is destroyed f) Leadout wire sufficiently fixed to the metal screen I.6 Heating I.6.1 No excessive temperatures in normal use I.6.2 I.6.3 Result Remark Used material classified as Class... : Stated value of ta... : Temperature rises (Upri: 1.06 time supply rated voltage) Determined temperature rises in windings: rimary (K)... : Limit max (K)... : Secondary (K)... : Limit max (K)... : After the test: no connections have worked loose no reduction of creepage distances and clearances no flow of sealing compound no operation of protecting devices electric strength test between input and output windings Cycling test (10 cycles):
age 17 of 33 I.6.3.1 heat run at (K)... : I.6.3.2 moisture treatment 48 h I.6.3.3 vibration test 1 h; 1,5 g I.6.3.4 After the tests: insulation resistance 2, 4 or 5 M dielectric strength test for 2 min. at 35 % of specified value in table I.6 Current or the ohmic component does not deviates by more than 30 % I.7 Shortcircuit and overload protection I.7.1 Upri: 1.06 times rated voltage or 0.94 and 1.06 times rated supply voltage (V)... : I.7.2 I.7.3 I.7.4 Determined temperature rise in windings and on other parts: test according to... : rimary winding (K)... : Limit max (K)... : Secondary winding (K)... : Limit max (K)... : External enclosure < 80 (K)... : Rubber insulation of wiring < 60 (K)... : VC insulation of wiring < 60 (K)... : Supports < 80 (K)... : I.7.5 Failsafe convertors I.7.5.1 Upri: 1.06 times rated supply voltage... V: Isec: 1.5 times rated output current... A: time until steadystate conditions t1 (h)... : time until failure t2 (h): < t1; < 5 h... : During the test: no flames, molten material, etc. temperature rise of enclosure < 150 K temperature rise of plywood support < 100 K After the test: I.7.5.2 Result Remark
age 18 of 33 Result Remark electric strength (test voltage; 35 % of specified value); no flashover or breakdown for primarytosecondary and for primarytobody live parts not accessible by test finger through holes of enclosure I.8 Insulation resistance and electric strength I.8.1 Conditioned 48 h between 91 % and 95 % I.8.2 Adequate insulation (500 V d.c. for 1 min) between: Live parts and the body for basic insulation not less than 2 M... : Live parts and the body for reinforced insulation not less than 4 M... : Input and output circuits not less than 5 M... : Metal parts of class II convertors which are separated from live parts by basic insulation only and the body not less than 5 M... : Metal foil in contact with the inner and outer surfaces of enclosures of insulating material not less than 2 M... : Electric strength test: 1) Between live parts of input circuits and live parts of output circuits... : 2) Over basic or supplementary insulation between: a) live parts which are or may become of different polarity... : b) live parts and body if intended to be connected to protective earth... : c) accessible metal parts and a metal rod of the same diameter as the flexible cable or cord... : d) live parts and an intermediate metal part... : e) intermediate metal parts and the body... : 3) Over reinforced insulation between the body and live parts... : No flashover or breakdown occurred I.8.3
age 19 of 33 I.9 Construction I.9.1 Comply with all requirements I.9.2 The distance between input and output terminals shall not be less than 25 mm... : I.10 Components I.10.1 Socketoutlets in the output circuit does not accept plugs complying with IEC 60083 and IEC 609061 I.10.2 Selfresetting protective devices shall not be used unless it is certain that there will be no hazards Compliance is checked by connecting the convertor for 48 h at 1.06 times the rated voltage with the output shortcircuited Creepage distances and clearances 1. Insulation between input and output circuits: a) measured values > specified values (mm)... : b) measured values > specified values (mm)... : c) measured values > specified values (mm)... : 2. Insulation between adjacent input circuits: measured values > specified values (mm)... : 2. Insulation between adjacent output circuits: measured values > specified values (mm)... : 3. Insulation between terminals for external connection: a) measured values > specified values (mm)... : b) measured values > specified values (mm)... : c) measured values > specified values (mm)... : 4. Basic or supplementary insulation: a) measured values > specified values (mm)... : b) measured values > specified values (mm)... : c) measured values > specified values (mm)... : 5. Reinforced insulation: measured values > specified values (mm)... : I.11 Result Remark
age 20 of 33 Result Remark 6. Distance through insulation: a) measured values > specified values (mm)... : b) measured values > specified values (mm)... : c) measured values > specified values (mm)... : d) measured values > specified values (mm)... :
age 21 of 33 Result Remark ANNEX 2: components object/part No. code manufacturer/ trademark type/model technical data standard mark(s) of conformity 6094774 */UL Connector B BJB 46.102 9A, 320V CB B ViaSystems FR4, R/C (ZMV2) rated min. V1, 125 C UL CB B Bergquist MCCB,, R/C rated min. V1, (ZMV2) 125 C UL Wiring B 24AWG Wire R/C (AVLV2) */UL rated min. 24 AWG, 300 V * Tested as part of the appliance. The codes above have the following meaning: A The component is replaceable with another one, also certified, with equivalent characteristics B The component is replaceable if authorised by the test house C Integrated component tested together with the appliance D Alternative component
age 22 of 33 Result Remark ANNEX 2a: temperature measurements, thermal tests of Section 12 Type reference... : Xicato XIM Lamp used... : LED Module XIM Lamp control gear used... : owered by external DCsource Mounting position of luminaire... : Mounted on a heatsink in open air. Supply wattage (W)... : 32 W Supply current (A)... : 1,1 Adc (max) Calculated power factor... : Table: measured temperatures corrected for ta = 25 C: abnormal operating mode... : test 1: rated voltage... : 26 V test 2: 1,06 times rated voltage or 1,05 times rated wattage... : test 3: Load on wiring to socketoutlet, 1,06 times voltage or 1,05 times wattage... : test 4: 1,1 times rated voltage or 1,05 times rated wattage... : Through wiring or loopingin wiring loaded by a current of A during the test... : 12.4 normal temperature ( C) of part 12.5 abnormal test 1 test 2 test 3 limit test 4 limit CB connector 67 120 CB Led 99 120 Wiring 85 150 Tc point 61 90
age 23 of 33 Result Remark ANNEX 3: screw terminals (part of the luminaire) (14) SCREW TERMINALS (14.2) Type of terminal...: Rated current (A)...: (14.3.2.1) One or more conductors (14.3.2.2) Special preparation (14.3.2.3) Terminal size Crosssectional area (mm²)...: (14.3.3) Conductor space (mm)...: (14.4) Mechanical tests (14.4.1) Minimum distance (14.4.2) Cannot slip out (14.4.3) Special preparation (14.4.4) Nominal diameter of thread (metric ISO thread)..: M External wiring No soft metal (14.4.5) Corrosion (14.4.6) Nominal diameter of thread (mm)...: Torque (Nm)...: Between metal surfaces Lug terminal Mantle terminal ull test; pull (N)...: Without undue damage (14.4.7) (14.4.8)
age 24 of 33 Result Remark ANNEX 4: screwless terminals (part of the luminaire) (15) SCREWLESS TERMINALS (15.2) Type of terminal...: Rated current (A)...: (15.3.1) Material (15.3.2) Clamping (15.3.3) Stop (15.3.4) Unprepared conductors (15.3.5) ressure on insulating material (15.3.6) Clear connection method (15.3.7) Clamping independently (15.3.8) Fixed in position (15.3.10) Conductor size Type of conductor (15.5) Terminals and connections for internal wiring (15.5.1) Mechanical tests (15.5.1.1.1) ull test springtype terminals (4 N, 4 samples).: (15.5.1.1.2) ull test pin or tab terminals (4 N, 4 samples) : Insertion force not exceeding 50 N (15.5.1.2) ermanent connections: pulloff test (20 N) (15.6) Electrical tests Voltage drop (mv) after 1 h (4 samples)...: Voltage drop of two inseparable joints Number of cycles...: Voltage drop (mv) after 10th alt. 25th cycle (4 samples)...: Voltage drop (mv) after 50th alt. 100th cycle (4 samples)...: After ageing, voltage drop (mv) after 10th alt. 25th cycle (4 samples)...:
age 25 of 33 (15.7) (15.8.1) (15.9) Result Remark After ageing, voltage drop (mv) after 50th alt. 100th cycle (4 samples)...: Terminals external wiring Terminal size and rating ull test springtype terminals or welded connections (4 samples); pull (N)...: ull test pin or tab terminals (4 samples); pull (N)...: Contact resistance test Voltage drop (mv) after 1 h terminal 1 2 3 4 5 6 7 8 9 10 voltage drop (mv) Voltage drop of two inseparable joints Voltage drop after 10th alt. 25th cycle Max. allowed voltage drop (mv)... : terminal 1 2 3 4 5 6 7 8 9 10 voltage drop (mv) Voltage drop after 50th alt. 100th cycle Max. allowed voltage drop (mv)... : terminal 1 2 3 4 5 6 7 8 9 10 voltage drop (mv) Continued ageing: voltage drop after 10th alt. 25th cycle Max. allowed voltage drop (mv)... : terminal 1 2 3 4 5 6 7 8 9 10 voltage drop (mv) Continued ageing: voltage drop after 50th alt. 100th cycle Max. allowed voltage drop (mv)... : terminal voltage drop (mv) 1 2 3 4 5 6 7 8 9 10
age 26 of 33 Result Remark
age 27 of 33 ictures: hotographs of overall construction (XIMCC series) Representative for XIMCV series
age 28 of 33 hotographs of LED module and connection board Integrated LED module representative for both series
age 29 of 33 Closeup of connection board and LED module
age 30 of 33 hotographs of the 010V dimmable electronics (XIMCV ). Representative for DALI version
age 31 of 33 hotographs of the dimmable version (XIMCV ). hotographs of the dimmable version (XIMCV ).
age 32 of 33 Closeup of connection board and LED module hotographs of the electronics dimmable version (XIMCV ).
age 33 of 33 LED module