Press control lock PS Type pproved ccording to DIN EN 693 Description The press control locks PS in the nominl sizes 06 nd 0 re modulr control locks with EC type pprovl for use in hydrulic presses ccording to the DIN EN 693 sfety regultions. The hydrulic control system conforms to performnce level PL e ccording to DIN EN ISO 3849. y using other sfety-relted control system prts, the performnce level PL e cn lso e chieved for the entire mchine. Due to its modulr design, the hydrulic control system cn e dpted to the functionl requirements of the press. A complete hydrulic control system is mde up t lest of the sic module nd counterlnce module. The sic module includes the pump s pressure djustment, the direction control for the press, nd the option of decompressing the piston side of the press cylinder. It lso includes protection ginst un desirle pressure uild-up on the piston side of the press cylinder required in DIN EN 693. The counterlnce module hs direct-cting pressure relief vlve for limiting ginst pressure intensifiction on the ring side of the press cylinder nd monitored directionl vlve. Together with the monitored direction vlve in the sic module, the ltter performs the redundnt nd monitored retining of the press rm. The functionl scope of the press control locks cn e optionlly extended s follows: Proportionl system pressure djustment Sfe set-up speed with pump (only possile in connection with liner position mesurement system) Set-up y grvity Fst dvnce y grvity or with regenertive circuit Counterlnce vi electronic or mechnicl lod holding vlve Accumultor module Additionl functions vi ML longitudinl stcking system Aville models sic module (compulsory equipment) ML function module (option for dditionl functions) Accumultor module (option) Counterlnce module (compulsory equipment) Sndwich pltes (optionl) Your enefits EC type pproved hydrulic control system ccording to DIN EN 693 Modulr nd compct design, functions cn e extended Simple nd roust control system set-up Miniml spce, piping nd mintennce required Cn e expnded to crete complete system The press control locks re optimlly djusted to suit the ppliction nd cn e used regrdless of the trnsmission drive Since the control locks re comined with the vrile-speed KineSys drive systems, dditionl functionlities cn e integrted nd therefore the complexity of the vlve control system cn e reduced Technicl dt Generl dt Nominl sizes Size 06 Size 0 Design Modulr design Weight nd dimensions See pges nd Connections (hydrulic) See pges nd Amient temperture rnge Min. - 0 C to mx. + 60 C Instlltion position Any, preferly in horizontl position Hydrulic specifictions Nominl sizes Size 06 Size 0 Mximum operting pressure* 350 r 30 r Mximum flow rte in P chnnel 60 l/min 00 l/min Mximum flow rte in T chnnel 80 l/min 0 l/min Operting fluid Hydrulic oil ccording to DIN 554, Prts nd Medi operting temperture rnge Min. - 0 C to mx. + 80 C Operting fluid viscosity rnge Min. 0 cst to mx. 380 cst Clenliness clss ccording to ISO 4406 Clss 9 / 7 / 4 or clener Electricl specifictions Nominl sizes Size 06 Size 0 Type of voltge Direct current Nominl voltge 4 V Voltge tolernce ± 0 % Protection clss IP 65 ccording to DIN 40050 (when instlled correctly) Electricl connection of solenoid vlves Plug ccording to EN 7530-803 (DIN 43650) (not included in the scope of delivery) Electricl connection for switch position monitoring Electricl connection for sensors Mx plug, 4-pin, coding A (not included in the scope of delivery) * Note: When using the counterlnce module S5, mximum = 80 r is permitted.
Model code TYPE Nominl size 06 Nominl size 06 0 Nominl size 0 Series X Determined y mnufcturer PS 06 X G 0 ML 00 S SP 0 0 0 00 Z 0 ASIC MODULE (compulsory equipment) System pressure monitoring (pos. 30) 0 Without system pressure monitoring HDA 4700-A (4 0 ma) HDA 4700- (0 0 V) 3 EDS 3400 System pressure djustment nd decompression (pos. 0 + 70 + 40) System pressure djustment vi vrile speed drive possile Decompression with directionl vlve System pressure djustment with proportionl vlve Decompression with directionl vlve 3 System pressure djustment vi vrile speed drive Decompression vi vrile speed drive Sfe system depressurising (pos. 90) 0 Vi vrile speed drive (without directionl vlve) With monitored directionl vlve Vi vrile speed drive (with unmonitored directionl vlve) ypss (pos. 0) 0 Without ypss With directionl vlve (minimum pump flow rte) With monitored directionl vlve Direction vlve (pos. 0) Centre position locked Centre position piston side depressurised ML FUNCTION MODULE (option for dditionl functions) 00 Without ML function module XX With ML function module, see dt sheet EN 5.308.0 COUNTERALANCE MODULE (compulsory equipment on rod side) 0 Without counterlnce vlve (pos. 30) nd return vlve (pos. 30) With counterlnce vlve (pos. 30) nd return vlve (pos. 30) With counterlnce vlve (pos. 30) nd fst dvnce vlve (pos. 30) 3 With proportionl counterlnce vlve (pos. 30) nd return vlve (pos. 30) 4 With proportionl counterlnce vlve (pos. 30) nd fst dvnce vlve (pos. 30) 5 With lod holding vlve (pos. 80) for counterlnce nd return ACCUMULATOR MODULE (option) 00000 Without ccumultor module Accumultor pressure limiting (pos. 530) CE pressure relief vlve p mx = 40 r CE pressure relief vlve p mx = 0 r 3 CE pressure relief vlve p mx = 330 r 4 CE pressure relief vlve p mx = 350 r Accumultor pressure monitoring (pos. 540) 0 Without ccumultor pressure monitoring HDA 4700-A (4 0 ma) HDA 4700- (0 0 V) 3 EDS 3400 Accumultor dischrge (pos. 50) Mnul dischrge (needle vlve) Electric dischrge (directionl vlve initil position closed) 3 Electric dischrge (directionl vlve initil position open) ML function module (ccumultor module dditionl functions) 00 Without ML function module XX With ML function module, see dt sheet EN 5.308.0 SANDWICH PLATES (option) 0 Without sndwich plte A Set-up y grvity (ctegory PL c) Set-up y grvity (ctegory PL d) C Set-up y grvity (ctegory 3 PL d) Regenertive circuit 3 Fst dvnce cylinder
Structurl design Compulsory equipment A sfe hydrulic control system ccording to EN 693 lwys requires comintion of sic module nd counterlnce module. Functionl scope. sic module System pressure limiting System pressure djustment System pressure monitoring Direction control Decompression Pump nd tnk connections P nd T. ML function module (dditionl functions) Switching dditionl functions with min drive 3. Counterlnce module Ring side pressure intensifiction protection Retining of press rm Counterlnce vlve Fst dvnce movement Cylinder connections A nd Guge ports MA nd M Schemtic design 4. Accumultor module Pressure holding Accumultor sfety Accumultor dischrge Accumultor connection M MA A 3. Counterlnce module (compulsory equipment) 6. Sndwich pltes (option) 5. ML function module (ccumultor module dditionl functions) Switching dditionl functions from ccumultor 6. Sndwich pltes Set-up y grvity Regenertive circuit Fst dvnce cylinder 5. ML function module (option) 4. Accumultor module (option). sic module (compulsory equipment) P T. ML function module (option) 3
Description of the sic module - G****- 0 - G****- /- G****- 40 Size 6 Y40 S0-0 0 30 - G*3***- 40 Size 6 W Decompression Y0 P T Y0 - G****- P-ML -ML00- S0-0 T-ML T-SP 0 W Y0 P T Y0 Direction vlve 60 3 T-D -ML0- Y50 MP 40. 40. 80 00 -ML**- Other options on request ML function module - G3****- 30 p = *r U/I 4 0 ma P 0 0 V - G****- P 30 U 0 0 V - G****- P 30 I System pressure monitoring 50 MP P P - G****- / - G****- - G*3***- T-SP T T-D - G**0**- - G***0*- 90 0 - G****- - G****- Y90 Y0 T - G****- / - G*3***- - G****- Y70 70 DN6 p = *r System pressure djustment - G****- - G****- Y90 Y0 System pressure djustment nd decompression 90 0 S0 Sfe ypss system depressurising The pump nd tnk lines re connected to the sic module. The sic module includes the mnully djustle pressure relief vlve (pos. 60) for limiting the system pressure. Proportionl press force djustment (pos. 70) is possile s n option. Sfe system depressurising is crried out vi the monitored directionl vlve pos. 90 s stndrd. Alterntively, this sfety function cn e relocted to the vrile-speed drive (DVA with Sfe Torque Off). If vrile-speed drive is used, the minimum pump flow rte cn e dischrged to the tnk vi the directionl vlve pos. 0. Set-up t sfe speed is possile y vrile speed drive (DVA with Sfely Limited Speed) if the vlve pos. 0 is monitored nd position encoder is used. Two different position-monitored 4/3 directionl vlves (pos. 0) re ville s options (initil position locked or initil position depressurised from A to T) for direction control. Together with the monitored directionl vlve in the counterlnce module, it lso performs the required redundnt nd monitored retining of the press rm. The press cylinder is decompressed using the directionl vlve pos. 40. The system pressure cn optionlly e mesured s n nlogue signl or e evluted with n electronic pressure switch (pos. 30). Vrious ML function modules cn e connected for dditionl functions. 4 0 ma S90 90 0 70 73 73 0 4
Description of the counterlnce modules Counterlnce module S0 Without counterlnce vlve M 390 M8 MA A The counterlnce module S0 includes the selle pressure relief vlve ginst pressure intensifiction (pos. 330) nd the position-monitored retining vlve (pos. 350). The press cylinder s A nd lines re connected to the counterlnce module. Mesurement devices cn e connected to the MA nd M connections if necessry. S350 Y350 330 350 300 Counterlnce module S With counterlnce vlve 30 M 390 M8 30 MA S350 Y350 A 330 350 The counterlnce module S includes the selle pressure relief vlve ginst pressure intensifiction (pos. 330) nd the position-monitored retining vlve (pos. 350). During return stroke of the press rm the mnully djustle counterlnce vlve (pos. 30) is ypssed over the check vlve (position 30). The press cylinder s A nd lines re connected to the counterlnce module. Mesurement devices cn e connected to the MA nd M connections if necessry. 300 Counterlnce module S Fst dvnce y grvity 30 Y30 M 390 M8 30 MA S350 Y350 A 330 350 The counterlnce module S includes the selle pressure relief vlve ginst pressure intensifiction (pos. 330) nd the position-monitored retining vlve (pos. 350). During return stroke of the press rm the mnully djustle counterlnce vlve (pos. 30) is ypssed over the directionl vlve in its initil position (position 30). When using prefill vlve on the cylinder, the fst dvnce cn e initited y switching the directionl vlve (pos. 30). The press cylinder s A nd lines re connected to the counterlnce module. Mesurement devices cn e connected to the MA nd M connections if necessry. 300 Counterlnce module S3 Electronic counterlnce vlve 300 30 M 390 M8 30 Y30 MA A S350 330 Y350 350 The counterlnce module S3 includes the selle pressure relief vlve ginst pressure intensifiction (pos. 330) nd the position-monitored retining vlve (pos. 350). The proportionlly djustle counterlnce vlve (pos. 30) enles infinitely vrile nd therefore optimum energy-relted dpttion to different tool weights. During return stroke of the press rm the mnully djustle counterlnce vlve (pos. 30) is ypssed over the check vlve (position 30). The press cylinder s A nd lines re connected to the counterlnce module. Mesurement devices cn e connected to the MA nd M connections if necessry. 5
Counterlnce module S4 300 30 Y30 M 390 M8 30 Y30 MA A S350 330 Y350 350 Electronic counterlnce vlve nd fst dvnce y grvity The counterlnce module S4 includes the selle pressure relief vlve ginst pressure intensifiction (pos. 330) nd the position-monitored retining vlve (pos. 350). The proportionlly djustle counterlnce vlve (pos. 30) enles infinitely vrile nd therefore optimum energy-relted dpttion to different tool weights. When using prefill vlve on the cylinder, the fst dvnce cn e initited y switching the directionl vlve (pos. 30). During return stroke of the press rm the mnully djustle counterlnce vlve (pos. 30) is ypssed over the directionl vlve in its initil position (position 30). The press cylinder s A nd lines re connected to the counterlnce module. Mesurement devices cn e connected to the MA nd M connections if necessry. Counterlnce module S5 800 MX 80 3 M6 M M8 870. MA S830 Y830 830 A 80 With lod holding vlve The counterlnce module S5 includes the selle pressure relief vlve ginst pressure intensifiction (pos. 80) nd the position-monitored retining vlve (pos. 830). The mnully djustle lod holding vlve (pos. 80) enles lod-independent counterlnce function. During return stroke of the press rm medi flows through the initil position of the vlve. The press cylinder s A nd lines re connected to the counterlnce module. Mesurement devices cn e connected to the MA nd M connections if necessry. For this vrint mximum presssure of 80 r is permitted. 6
Description of the sndwich pltes Sndwich plte Z 90 M8 90 Y90 930 Set-up y grvity When using the sndwich plte ZA nd prefill vlve on the cylinder, the press rm cn e lowered y switching the directionl vlve (pos. 90) t sfe speed (ctegory PL c). The sndwich plte cn e expnded to increse the level of sfety: Z: pos. 90 switch position-monitored (ctegory PL d) ZC: dditionl vlve pos. 930 (ctegory 3 PL d) 900 Sndwich plte Z Regenertive circuit The sndwich plte Z cn e used to reduce cycle time. y switching the position monitored directionl vlve (position 70) the oil flow from the ring side of the cylinder is routed to the piston side insted of to tnk. If the fst dvnce stroke is reched, the vlve is switched off gin. 70 70 Y70 S70 Sndwich plte Z3 A Y460 MA 470 460 Size Fst dvnce cylinder The sndwich plte Z3 cn lso e used to reduce cycle time. y switching the directionl vlve (position 460) the pump flow is guided to the fst dvnce cylinder(s) vi the connection A. The press cylinder feeds vi prefill vlve during fst dvnce. If the fst dvnce stroke is reched, the vlve is switched off gin. The pump flow is now guided oth to the fst dvnce cylinder nd to the press cylinder. 450 489346 7
Description of the ccumultor module The ccumultor module is designed for connecting hydrulic ccumultor. It enles n energy-efficient pressure retention mode over long period of time. The mximum permissile ccumultor-chrging flow rte must e selected depending on the CE pressure relief vlve (see PS opertion mnul). During uxiliry process times, dditionl functions cn e operted from the ccumultor even when the min pump is off, or disconnected y the directionl vlve position 50. Different ML function modules cn e connected for this purpose. The ccumultor module includes ll the oil-side ccumultor sfety elements: the CE pressure relief vlve in different pressure stges (pos. 530), mnul decompression vlve, nd mechnicl pressure indictor. With the optionl directionl vlve pos. 50, the ccumultor cn e dischrged electriclly. The ccumultor pressure cn either e mesured s n nlogue signl or with n electronic pressure switch (pos. 540). - SP****- - SP****- - SP3****- - SP4****- p = 40 r p = 0 r p = 330 r p = 350 r CE CE CE CE 530 530 530 530 - SP***00 - - SP***** - - SP00000-630 500 Y50 50 570 P-ML 60 630 - SP***0 - Y60 550 0 400 r T-ML SP SP MSP 570.3 570. 640 630 - SP**** - - SP**3** - 560 MSP MSP 570.4 570. 400 540 - SP***** - Other options on request - SP**** - - SP**** - - SP*3*** - P P 540 540 540 p = * r I U - SP**** - - SP**** - - SP**3** - Y50 Y50 50 50 50 DN08 A 4 0 ma 0 0 V U / I 4 0 ma P 0 0 V 8
Specific exmple Type: PS-06--G0-ML00-S-SP00000-Z0 Mteril: 468 The specific exmple shows sic vrint of the press control lock in nominl size 06 with fixed displcement pump. The trvel speed depends on the pump size. It is not possile to switch etween fst dvnce nd press speed. The system pressure cn only e djusted mnully. The monitored vlves pos. 90, 0 nd 350 prevent dngerous motion nd undesirle strting. The control system shown elow lso includes the sic vrint of the counterlnce function (counterlnce module S). M 390 M MA G¾ 0 300 30 30 S350 330 S0-0 Y350 350 0 Y0 P T Y0 40 Y40 30 P-ML T-ML T-SP 60 70 3 73 T-D 400 30 4 0 ma P I MP 40. 40. 0 Y90 80 S90 90 00 Ø * 0 50 MP P G¾ P G¾ T-SP T G T-D T G M sic module Mximum pressure limiting, mnully djustle (pos. 60) System pressure monitoring with HDA 4700-A (pos. 30) Sfe system depressurising with monitored vlve (pos. 90) Directionl vlve for decompression (pos. 40) Direction control with monitored vlve (pos. 0, prevention of undesirle pressure uild-up nd retining) Counterlnce module Protection ginst pressure intensifiction (pos. 330) on the ring side of the press cylinder Counterlnce vlve (pos. 30) Return vlve (pos. 30) Rm retining with monitored vlve (pos. 350) Hydrulic drive Hydrulic drive with constnt flow rte 9
Specific exmple Type: PS-0--G0-ML00-S-SP00000-Z0 Mteril: 4683 The specific exmple shows press control lock in nominl size 0 with vrile-speed drive (DVA) with Sfe Torque Off (STO). In the context of the motor nd pump performnce dt, ny fst dvnce, press nd return speeds re possile. When using suitle mesuring systems, the pressure, position nd speed cn e controlled using the hydrulic drive. The monitored vlves pos. 0 nd 350 plus the STO function of the hydrulic drive ring the dngerous motion to stndstill nd prevent undesirle strting. A second monitored vlve cn e wived to prevent undesirle pressure uild-up. The control system shown elow lso includes the sic vrint of the counterlnce function (counterlnce module S). L I G M 390 M MA 0 300 30 30 S350 330 S0-0 Y350 350 0 A Y0 P T Y0 40 Y40 30 P-ML T-ML T-SP 60 70 3 73 T-D 400 30 4 0 ma P I MP 40. 40. 0 80 90 00 Ø * 0 50 MP P P T-SP T-D T T HFI STO M sic module Mximum pressure limiting, mnully djustle (pos. 60) System pressure monitoring with HDA 4700-A (pos. 30) Directionl vlve for decompression (pos. 40) Direction control with monitored vlve (pos. 0, prevention of undesirle pressure uild-up nd retining) Hydrulic drive Vrile-speed drive with chnging flow rte Closed loop pressure control possile Closed loop position control possile Closed loop speed control possile Prevention of undesirle pressure uild-up (Sfe Torque Off) Counterlnce module Protection ginst pressure intensifiction (pos. 330) on the ring side of the press cylinder Counterlnce vlve (pos. 30) Return vlve (pos. 30) Rm retining with monitored vlve (pos. 350) 0
Specific exmple Type: PS-0--G-ML00-S3-SP330-Z Mteril: 4684 The specific exmple shows press control lock in nominl size 0 with vrile-speed drive (DVA) with Sfely- Limited Speed (SLS). In the context of the motor nd pump performnce dt, ny fst dvnce, press nd return speeds re possile. When using suitle mesuring systems, the pressure, position nd speed cn e controlled using the pump drive. The monitored vlves pos. 90, 0 nd 350 ring the dngerous motion to stop nd prevent undesirle strting. A sfe strt-up mode with the pump is enled due to the monitored ypss vlve pos. 0, the SLS function of the trnsmission drive, nd the liner position mesurement system. The control system shown lso includes the ccumultor module with ML function module, counterlnce module S3 (proportionl counterlnce vlve) nd the sndwich plte Z (regenertive circuit). L I G M 390 M MA 0 300 60 630 640 30 Y60 30 S350 330 Y350 Y30 350 500 P-ML 70 P T A 70 Y70 S70 Y50 50 Y0 A P S0-0 T Y0 Y40 30 P-ML T-ML T-SP 550 0 400 r 560 T-ML SP SP MSP MSP 570. 570.3 570.4 570. MSP3 P I 540 4 0 ma p = 330 r 530 CE Y50 50 30 4 0 ma P I MP MP P 40. 40. 0 P Y90 60 3 70 73 Y0 S90 S0 00 Ø* 0 T-SP T-D T T-D T HFI SLS M sic module Mximum pressure limiting, mnully djustle (pos. 60) System pressure monitoring with HDA 4700-A (pos. 30) Directionl vlve for decompression (pos. 40) Sfe system depressurising with monitored vlve (pos. 90) Direction control with monitored vlve (pos. 0, prevention of undesirle pressure uild-up nd retining) ypss with monitored vlve Counterlnce module Protection ginst pressure intensifiction (pos. 330) on the ring side of the press cylinder Proportionl counterlnce vlve (pos. 30) Return vlve (pos. 30) Rm retining with monitored vlve (pos. 350) Accumultor module 330 r CE pressure relief vlve (pos. 530) Electric ccumultor dischrge (pos. 50, open when de-energised) Accumultor pressure monitoring with HDA 4700-A (pos. 540) ML function module (pos. 60, 630 nd 640) Sndwich plte Differentil vlve (pos. 70) Hydrulic drive Vrile-speed drive with chnging flow rte Closed loop pressure control possile Closed loop position control possile Closed loop Speed control possile Sfely limited pump speed (Sfely Limited Speed)
Nominl size 06 Weights Module Weight (kg) Height H (mm) G***** 7.8 5 (HG) S S5 8.9 80 (HS) SP***** 7.5 80 Z 3. 8 (HZ) Z 7.3 59 (HZ) Z3 5.8 60 (HZ) Hydrulic connections Connection Size T, T G P, P, A G¾ T-SP, T-SP, T-D, T-D, SP, SP, A, MA, MA, M
Nominl size 0 4xM 0 0 60 70 0 5 50 P T T-D T-SP 35 80 95 00 95 55 0 54 48 0 0 H= HG + HS + HZ 0 55 80 30 70 0 40 45 0 4 60 60 40 A 60 70 0 mx. 366 P 5 0 40 0 T-D T T-SP mx. 444 Weights Module Weight (kg) Height H (mm) G***** 35.3 55 (HG) S S5.4 5 (HS) SP***** 7.5 80 Z 4.6 33 (HZ) Z.7 90 (HZ) Z3 5.9 65 (HZ) Hydrulic connections Connection Size T, T P, P, A A T-SP, T-SP, T-D, T-D, SP, SP, A, MA, MA, M G G¾ 3
Position monitoring switch Performnce dt for inductive limit switch IES 00 Supply voltge 0 3 V DC Current consumption 400 ma Mx. output current 400 ma Output signl PNP Switching hysteresis 0. mm EMC DIN EN 6000-6- / / 3 / 4 Plug Mx ccording to DIN 40050 Direction vlve pos. 0 PIN connection Sfe system depressuring pos. 90, sfe set-up flow rte pos. 0, rm retining vlve pos. 350 / pos. 380 nd differentil vlve pos. 70 PIN connection pnp 3 + + 4 R 4 R 4 V 4 V R pnp R 4 3-3 - 3 4 Pin Vlue Function + 4 V supply NC normlly closed 3 0 V 4 NC normlly closed Pin Vlue Function + 4 V supply NC normlly closed 3 0 V 4 NO normlly open Switching logic Switching logic Signl Signl pin 4 Signl 0 pin 4 Signl 0 Signl pin Signl Signl 0 Signl 0 pin -00-50 0 stroke (%) 50 00 0 50 stroke (%) 00 Sensors Pressure trnsmitter HDA 4700 PIN connection Pressure switch EDS 3400 PIN connection Pin HDA 47X6-A HDA 47X6- Pin EDS Signl + +U +U n. c. n. c. Anlogue 3 Signl - 0 V 3 0 V 4 n. c. Signl Mx Mx, 4-pin 4 SP For technicl dt, see dt sheet DE 8.306.4 For technicl dt, see dt sheet EN 8.060. 4
Pressure flow resistnce for nominl size 06 p (r) 50.000 45.000 40.000 35.000 30.000 5.000 0.000 A-T -T P- P-A 5.000 0.000 5.000 0.000 0.00 6.00.00 8.00 4.00 30.00 36.00 4.00 48.00 54.00 60.00 Q (l/min) Mesured with counterlnce module S0 t ϑ = 46 cst nd T Oil = 40 C Pressure flow resistnce for nominl size 0 p (r) 50.000 45.000 40.000 35.000 30.000 5.000 0.000 5.000 A-T -T P- P-A 0.000 5.000 0.000 0.00 0.00 0.00 30.00 40.00 50.00 60.00 Mesured with counterlnce module S0 t ϑ = 46 cst nd T Oil = 40 C 70.00 80.00 90.00 00.00 Q (l/min) 5
EC type pprovl certificte NOTE The informtion in this rochure reltes to the operting conditions nd pplictions descried. For pplictions nd / or operting conditions not descried, plese contct the relevnt technicl deprtment. All technicl detils re suject to chnge without notice. HYDAC INTERNATIONAL GmH Industriestrße 6680 Sulzch / Sr Germny Tel.: +49 6897 509-0 Fx: +49 6897 509-577 E-mil: kinesys@hydc.com Internet: www.hydc.com 6