Using this tlog Step 1: Determine your pplition Go to the pge for your pplition: fe frme pge 9, pnel pge 11, or nrrow frme luminum door pge 13. Step 2: Clulte the power ftor Determining the Power ftor (PF) is importnt for hosing the lift mehnism tht works est with your inet nd doors. It is lulted y multiplying the inet height in inhes y the ext door weight (inluding twie the weight of the hndle) in pounds. Exmple: Power ftor (PF) = inet height [inh] x door weight* [l] (inluding 2 x the hndle weight) * For lultions, use the onversion hrt elow to determine door weight in deiml form. Cinet height: 24 inhes Door weight (inluding 2 x hndle): 23 l 14 oz (14 oz =.9 l). Weight onverted to deiml is 23.9 l Power ftor (PF) = 24 x 23.9 Power ftor (PF) = 574 Weight onversion hrt oz. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 l..1.1.2.3.3.4.4.5.6.6.7.8.8.9.9 Step 3: Selet proper lift mehnism set sed on power ftor Use the lulted Power ftor (PF) to selet the proper lift mehnism. Power ftor (PF) Opening ngle Prt No. 43-99 107 20K2300.NA 100-174 107 20K2500.NA 175-349 107 20K2700.NA 350-792 100 20K2900.NA Step 4: Selet the proper hrdwre set Selet the proper hrdwre set sed on the intended pplition. Wood/wide luminum door pplition Hrdwre set 20K4200.A1 Nrrow luminum door pplition Hrdwre set 20K4200AA1 Sujet to tehnil modifitions without notie. 2007
Step 5: Determine mounting lotion for lift mehnism Use the digrm for the pproprite pplition to determine the lif t mehnism loting hole positions nd pre-ore them in the inet sides. Step 5: Minimum spe requirement 106.5 Loting pin positions 5 106.5 Mounting hole lotions For fe frme pplitions, inet sides must e loked out. 205 261 Instlltion 85 Z The inluded #7 x 35 mm (1-3/8") wood srews re required in the three holes mrked in ornge. Step 5: Minimum spe requirement Loting Overlypin up positions to 28 32 35 Z 37 35 33 NOTE: Fe frme inets must e Mounting loked hole out lotions fl ush with the frme on the sides to mount the AVENTOS HK lift mehnisms. 106.5 5 106.5 85 Z Step 6: Determine mounting lotion for the mounting pltes 205 261 Overly up to 28 32 35 Z 37 35 33 The inluded #7 x 35 mm (1-3/8") wood srews re required in the three holes mrked in ornge. NOTE: Fe frme inets must e loked out fl ush with the frme on the sides to mount the AVENTOS HK lift mehnisms. Use the digrm for the pproprite pplition to determine mounting plte positions nd mount them on the doors. Step 6: Mounting plte position 41.5 + Overly + Overly 32 32 32 32 32 32 8 16 Mounting plte with rket 16 32 32 32 The mounting plte with rket (20S4F01) is required when the mounting plte enter line is in less thn 6mm from the enter pnel. 8 40 more thn 6 Use the stndrd mounting plte (20S4200) for solid doors or on fi ve pnel doors when the mounting plte enter line is in more thn 6mm from the enter pnel. less thn 6 19 Mounting plte 20S4200 Mounting plte with rket 20S4F01 Minimum gp Minimum ottom revel Deortive molding lerne Gp X Door thikness Step 7: Begin ssemly Now move to the Assemly instrutions on pge 17. NOTE: For doors with rdius of 1 mm. Overly up to 28 32 35 Gp 1.5 4 5 Min 2 Door thikness 16 19 22 26 X 70 59 49 35 Sujet to tehnil modifi tions without notie. 2007 10 Sujet to tehnil modifitions without notie. 2007 8
Wood or wide luminum door for fe frme pplitions d Determine required prts To determine the required lift mehnism set for ny pplition, lulte the power ftor sed on weight of the door (inluding doule the hndle weight) nd inet height. See formul elow NOTE: Fe frme inets must e loked out flush with the frme on the sides to mount the AVENTOS HK lift mehnisms. NOTE: For Mx. inet dimensions see pge 3 Using this tlog pge 7 Instlltion & removl pges 17-20 Power ftor (PF) = inet height in inhes x door weight in pounds (inluding doule the hndle weight) Lift mehnism 20K2300 PF 43-99 PF 100-174 20K2500 20K2700 PF 175-349 PF 350-792 20K2900 A tril pplition is reommended when you re in orderline re of the individul lift mehnism. PF Power ftor Required prts Step 3 thru Lift mehnism set Step 4: Wood/wide luminum door hrdwre set Set inludes: Set inludes: 2 x Lift mehnisms 2 x Cover pltes (right nd left) 2 x Cover ps 10 x #7x35mm (1-3/8 ) wood srews* d d 2 x 20S4200 Wood/wide luminum mounting plte 2 x 20S4F01 Wood/wide luminum mounting plte with rket 22 x 606P Wood door srews for 20S4200* 18 x 699.110 Aluminum door srews for mounting pltes* POZI #2x2 driver it for djusting tension * only 6 srews required * only 8 srews required Power ftor (PF) Opening ngle Prt No. 43-99 107 20K2300.NA 100-174 107 20K2500.NA 175-349 107 20K2700.NA 350-792 100 20K2900.NA Hrdwre set 20K4200.A1 9 Sujet to tehnil modifitions without notie. 2007
Instlltion Step 5: Minimum spe requirement Loting pin positions Mounting hole lotions 106.5 5 106.5 85 Z 205 261 The inluded #7 x 35 mm (1-3/8") wood srews re required in the three holes mrked in ornge. Overly up to 28 32 35 Z 37 35 33 NOTE: Fe frme inets must e loked out flush with the frme on the sides to mount the AVENTOS HK lift mehnisms. Step 6: Mounting plte position Mounting plte with rket 41.5 + Overly + Overly 32 32 32 32 32 32 8 16 16 32 32 32 The mounting plte with rket (20S4F01) is required when the mounting plte enter line is in less thn 6mm from the enter pnel. 8 40 more thn 6 Use the stndrd mounting plte (20S4200) for solid doors or on five pnel doors when the mounting plte enter line is in more thn 6mm from the enter pnel. less thn 6 ü 19 Mounting plte 20S4200 Mounting plte with rket 20S4F01 Minimum gp Minimum ottom revel Deortive molding lerne Gp X Door thikness NOTE: For doors with rdius of 1 mm. Overly up to 28 32 35 Gp 1.5 4 5 Min 2 Door thikness 16 19 22 26 X 70 59 49 35 Sujet to tehnil modifitions without notie. 2007 10
Wood or wide luminum door for pnel pplitions Determine required prts To determine the required lift mehnism set for ny pplition, lulte the power ftor sed on weight of the door (inluding doule the hndle weight) nd inet height. See formul elow NOTE: For Mx. inet dimensions see pge 3 Using this tlog pge 7 Instlltion & removl pges 17-20 Power ftor (PF) = inet height in inhes x door weight in pounds (inluding doule the hndle weight) Lift mehnism 20K2300 PF 43-99 PF 100-174 20K2500 20K2700 PF 175-349 PF 350-792 20K2900 A tril pplition is reommended when you re in orderline re of the individul lift mehnism. PF Power ftor Required prts Step 3 thru Lift mehnism set Step 4: Wood/wide luminum door hrdwre set Set inludes: Set inludes: 2 x Lift mehnisms 2 x Cover pltes (right nd left) 2 x Cover ps 10 x #7x35mm (1-3/8 ) wood srews* d d 2 x 20S4200 Wood/wide luminum mounting plte 2 x 20S4F01 Wood/wide luminum mounting plte with rket 22 x 606P Wood door srews for 20S4200* 18 x 699.110 Aluminum door srews for mounting pltes* POZI #2x2 driver it for djusting tension * only 6 srews required * only 8 srews required Power ftor (PF) Opening ngle Prt No. 43-99 107 20K2300.NA 100-174 107 20K2500.NA 175-349 107 20K2700.NA 350-792 100 20K2900.NA Hrdwre set 20K4200.A1 11 Sujet to tehnil modifitions without notie. 2007
Instlltion Step 5: Minimum spe requirement Loting pin positions Mounting hole lotions 5 96 37 The inluded #7 x 35 mm (1-3/8") wood srews re required in the three holes mrked in ornge. Step 6: Mounting plte position Mounting plte 13.5 + Overly 32 32 32 69 32 32 32 8 16 Mounting plte 20S4200 Minimum gp Minimum Revel Deortive molding lerne min 1.5 X Door thikness NOTE: For doors with rdius of 1 mm. Min 2 Door thikness 16 19 22 26 X 70 59 49 35 Sujet to tehnil modifitions without notie. 2007 12
Nrrow luminum door for pnel pplitions Determine required prts To determine the required lift mehnism set for ny pplition, lulte the power ftor sed on weight of the door (inluding doule the hndle weight) nd inet height. See formul elow NOTE: For Mx. inet dimensions see pge 3 Using this tlog pge 7 Instlltion & removl pges 17-20 Power ftor (PF) = inet height in inhes x door weight in pounds (inluding doule the hndle weight) Lift mehnism 20K2300 PF 43-99 PF 100-174 20K2500 20K2700 PF 175-349 PF 350-792 20K2900 A tril pplition is reommended when you re in orderline re of the individul lift mehnism. PF Power ftor Required prts Step 3 thru Lift mehnism set Step 4: Nrrow luminum door hrdwre set Set inludes: Set inludes: 2 x Lift mehnisms 2 x Cover pltes (right nd left) 2 x Cover ps 10 x #7x35mm (1-3/8 ) wood srews* d 2 x 20S4200A Nrrow luminum mounting plte 18 x 699.110 Aluminum door srews for nrrow frme luminum doors* POZI #2x2 driver it for djusting tension * only 6 srews required * only 8 srews required Power ftor (PF) Opening ngle Prt No. 43-99 107 20K2300.NA 100-174 107 20K2500.NA 175-349 107 20K2700.NA 350-792 100 20K2900.NA Hrdwre set 20K4200AA1 13 Sujet to tehnil modifitions without notie. 2007
Instlltion Step 5:Minimum spe requirement Loting pin positions Mounting hole lotions 5 96 37 The inluded #7 x 35 mm (1-3/8") wood srews re required in the three holes mrked in ornge. Step 6: Mounting plte position Mounting plte for nrrow frme luminum doors Overly 4.5 0.1 7 4 4.6 15-19 64 15.5 33 31 38 64 11.4 31 69 1-4 Overly 19-22 7.5 7.4 When hnging mteril thikness, djust the ssemly dimensions ordingly. Minimum gp Minimum Revel Deortive molding lerne min 1.5 X Door thikness NOTE: For doors with rdius of 1 mm. Min 2 Door thikness 16 19 22 26 X 70 59 49 35 Sujet to tehnil modifitions without notie. 2007 14
11 16 Assemly ids nd essories AVENTOS templte - Use to pre-ore for AVENTOS loting pins AVENTOS templte 65.5020 Ø5mm drill it DB-5mm Restrition lip - Restrits the openning ngle of the door - Prevents the door from hitting n ojet ove or to keep the hndle within reh on very high inets 100 degree 20K7041 75 degree 20K7011 Srews POZI DRIVER nd its Bumpers Use to tth mounting pltes to doors 3.5 6 3.5 6 A POZI srewdriver (different from Phillips) is the most ruil tool you n use to ssure tht full torque is pplied to ll Blum mounting srews. POZI srews n e identified y the distintive tik mrks loted in the enter of the srew hed reess. Cushions door losing Self-dhesive k; ler For luminum door mounting pltes For wood door mounting pltes 699.110 606P #2 POZI DRIVER #2x1" POZI it insert #2x2" POZI it insert 1/4" it holder POZI DRIVER POZI BIT #2x1 POZI BIT #2x2 BIT HOLDER 6(1/4") di. x 1.5(1/16") 10(3/8") di. x 3(1/8") FX4041 SJ5312 15 Sujet to tehnil modifitions without notie. 2007
Assemly Step 1: Complete n AVENTOS plnning worksheet Go through the "Using this tlog" steps on pges 7-8 or omplete n AVENTOS plnning worksheet (ville on www.lum.om). This will help you determine required hrdwre nd neessry inet preprtion. Step 2: Instll the lift mehnism. Use the AVENTOS templte to preore the loting pin holes for the AVENTOS HK lift mehnism.. After ligning the lift mehnism with the inet using the lotor pins, tth the mehnism with the three mounting srews provided. 3 x wood srews #7 x 35 mm Step 3: Remove wrning lel from lift mehnism nd rise rms Risk of injury: spring-loded lever rm - Do not push lever rm down or leve in the down position - Remove mehnism efore instlling or removing inet. Stnding t rm s length, refully remove the lel holding the rm in ple.. Rise the rm to the upright position. NOTE: Do not remove wrning lel until just efore tthing the door. 17 Sujet to tehnil modifitions without notie. 2007
Step 4: Atth the door Atth the door using the the CLIP lip mehnism in the mounting plte. Step 5: Adjust the door tension Use srew gun nd the supplied #2x2 POZI driver it to djust the lift mehnism to the desired tension. Step 6: Finlize the door djustments nd tth over ps. Use POZI srewdriver to djust m djustments for eh of the 3-dimensionl djustments.. Snp the symmetril over ps on eh over plte. Ple the left nd right over pltes over the pproprite lift mehnisms nd snp them in ple. Sujet to tehnil modifitions without notie. 2007 18
Removl Step 1: Be wre Risk of injury: spring-loded lever rm - Do not push lever rm down or leve in the down position - Remove mehnism efore instlling or removing inet Step 2: Remove the over pltes Remove the over ps nd over plte. Step 3: Remove the door. Open the door. Use srewdriver to disengge the CLIP mehnism of the lever rm from the mounting plte.. Support the door with one hnd nd repet on the other side. 19 Sujet to tehnil modifitions without notie. 2007