TECHNICAL INFORMATION Model. Description HR2610/ HR2611F/ HR2610T/ HR2611FT Combination Hammers 26mm (1") CONCEPT AND MAIN APPLICATIONS HR2610 series models are 26mm (1") combination hammers adapted for SDS-PLUS bits, featuring compact and lightweight design, enhanced comfort and better control with ergonomic handle. Model HR2610T/HR2611FT are equipped with quick change drill chuck while Model HR2611/HR2611FT are with AVT; Anti Vibration Technology consisting of Active dynamic vibration absorber with counterweight and Damper spring. AVT ensures operation with extremely low vibration, which is much superior to the competitors. HR2610 series models are available in the variations listed below, including HR2300 and HR2600 series models developed on the same concept. Model Capacity Operation Mode AVT LED Chuck type Dimensions: HR2300 23mm 2 modes HR2610 HR2610T HR2600 (Rotation only/ HR2611F HR2611FT Rotation with hammering) HR2601 Length (L) 361 (14-1/4) 385 (15-1/8) 26mm HR2610 Width (W) 77 (3) HR2611F Height (H) 209 (8-1/4) (Rotation only/ HR2310T 23mm Rotation with hammering/ *Round shank bits can also be used by HR2610T 26mm Hammering only) replacing the factory-mounted chuck with HR2611FT and Round shank bits* Quick change drill chuck (keyless). For information of HR2300 and HR2600 series models, see TECHNICAL INFORMATION of each series. Voltage (V) Current (A) Cycle (Hz) Continuous Rating (W) Input Output Max. Output (W) 110 7.7 120 7 --- 127 6.6 220 3.8 230 3.7 240 3.5 load speed: min ¹= rpm Impacts per minute= min ¹ Chuck type Concrete Vibration absorption Variable speed control Rotation reversing facility Torque limiter LED Job light Double insulation Power supply cord: m (ft) Model TCT bit Core bit Capacities: Diamond core bit Steel Wood Operation mode Weight according to EPTA-Procedure 01/2003*3: kg (lbs) PRODUCT P 1/ 6 HR2610/ HR2611F HR2610T/ HR2611FT 0-1,200 and Round shank bits*1 (Rotation only/ Rotation with hammering/ Hammering only) / (AVT*2) / (AVT*2) (by trigger) / / Europe, rth America:, Australia, Brazil: 2.0 (6.6), Other countries: 2.5 (8.2) 2.8/ 2.9 2.9/ 3.0 (6.1/ 6.4) (6.4/ 6.6) *1 Round shank bits can also be used by replacing the factory-mounted chuck with Quick change drill chuck (keyless). *2 AVT (Anti Vibration Technology); Counterweight mechanism + Damper spring *3 with side grip W L (The image above is HR2610/HR2611F.) H
P 2/ 6 Standard equipment Depth gauge... 1 pc Side grip... 1 pc Dust cup set... 1 pc (for some countries only) Quick change drill chuck (keyless)... 1 pc (HR2610T/ HR2611FT only) Carrying case... 1 pc (plastic or aluminum) te: The standard equipment for the tool shown above may vary by country. Optional accessories SDS-PLUS shank TCT hammer drill bits Taper shank TCT hammer drill bits Taper shank adaptor Cotter Core bits Center bits Core bit adaptor Rod Drill chuck ass'y Chuck adapter assembly Drill chuck S13 Chuck key S13 Tool holder set Scraper assembly Waterproof cover Quick change drill chuck (keyless) Dust cups 5 and 9 Hose Joint 25 Dust cup set Plastic carrying case Hammer grease (30g) Bit grease Depth gauge Blow out bulb Safety goggles Bull points Cold chisels Scaling chisels Grooving chisels Hammer service kit
Features and benefits [HR2611F, HR2611FT only] Extremely low vibration of 11.5-12.0m/s² achieved by AVT(Anti-Vibration Technology): Counterweight mechanism dampens the vibration produced by impact mechanism by moving a counterweight in the opposite direction to the movement of the piston. Damper spring absorbs reaction force caused by drill bit at the moment of impact. Compact and Lightweight design Although equipped with AVT: Features an overall length 9mm shorter than HR2470. Weighs as light as HR2470 series models. P 3/ 6 Counterweight mechanism Counterweight When the swash bearing moves the piston back and forth, it simultaneously makes the counterweight swing in the opposite direction to the piston in order to counteract the force produced by the movement of the piston. Damper spring Less bit wobbling compared with HR2470 series models obtained by making bit guide portion 9mm longer than that of the current models Quick change drill chuck (keyless) (HR2610T, HR2611FT only) 40 Different bit-angle settings The bit-angle is adjustable without chisel adapter. High durability * One-touch sliding chuck for easy bit changes Operation mode change lever positioned on the bottom of gear housing for reduced possibility of breakage Redesigned accessories * * * Easy depth adjustment Depth gauge can be adjusted with a single motion. Increased repairability The repairability of clutch cam is drastically increased by simplifying the mechanism of operation mode change. Easy-to-grip handle ergonomically designed to: give maximum power thrust. provide a sure and comfortable grip in any operation; overhead application, drilling with palm-up or palm-down grip. Rubberized soft grip * provides more comfort and control. Single-light LED job light * with afterglow function Torque limiter * (HR2611F, HR2611FT only) illuminates workpiece and drill bit brightly for efficient operation in dark environment. *The same advantages as HR2470 series models Plastic carrying case Easy to transport with large carrying handle Easy to open with large latches Stackable with other plastic carrying cases of the same size or different size Dust cup Higher visibility of the bit tip obtained by transparent cup mouth Large carrying handle Large latches Connectable with the hose of Makita vacuum cleaner without joint parts With Makita vacuum cleaner, this dust cup can efficiently extract dust and debris in a wide range of drilling operations; from overhead to vertical downward applications. Also can be used like the current dust cup by plugging the suction port.
Comparison of products Performance Comparison P 4/ 6 te: 1. The test results depend to a great extent on the hardness of materials, etc. 2. Numbers in the chart below are relative values when the capacities of HR2470 are indexed at. (1) Drilling Test conditions: Drilled holes to a depth of 40mm (1-9/16") using ø1.5mm² x 50m cord reel. Test material: Concrete with compressive strength of 40N/mm² Makita HR2610 series Makita HR2470 series BOSCH GBH2-26DRE HITACHI DH24PC3 [Work speed] [diameter: ø6.5mm (1/4")] 0 50 150 [Work speed] [diameter: ø10.5mm (5/16")] 95 0 50 150 Makita HR2610 series Makita HR2470 series BOSCH GBH2-26DRE HITACHI DH24PC3 [diameter: ø12.5mm( 1/2")] 110 0 50 150 [diameter: ø16.5mm (5/8")] 110 0 50 150 (2) Chipping Test conditions: Chipped concrete with compressive strength of 40N/mm², and measured the amount of concrete removed. small [Work speed] Large Makita HR2610 series Makita HR2470 series BOSCH GBH2-26DRE 130 130 0 50 150
Comparison of products P 5/ 6 Comparison Continuous rating input: W Rated amperage for rth America: A load speed: min ¹= rpm Impacts per minute= min ¹ Chuck type TCT bit Core bit Diamond core bit HR2610/ HR2611F Impact energy (EPTA): J 2.4 2.4 2.3 2.5*2 Impact energy*1: J 2.9 2.7 2.7 3.0 3.2 Operation mode: R= Rotation only R+H= Rotation with Hammering H= Hammering only Vibration absorption / (AVT*3) Vibration: m/s² / 12.0 ise: db(a) 91/ Rotation reversing facility Variable speed control LED Job light Power supply cord: m (ft) Weight according to EPTA- Procedure 01/2003*5: kg(lbs) Concrete Steel Wood Dimensions: Length Width Height Model 0-1,200 / 361 (14-1/4) 77 (3) 209 (8-1/4) *4 2.8/ 2.9 (6.1/ 6.4) Makita BOSCH HITACHI HR2470/ HR2470F HR2450(F)/ HR2451/ HR2452 GBH2-26DRE/ GBH2-26DE DH24PC3 370 (14-1/2) 84 (3-1/4) 214 (8-3/8) / / / / (F-model only)/ / 360 (14-1/8) 204 (8) 2.7 (6.0) *1 Measured according to our conventional reference, *2 Actually measured value, *3 AVT (Anti Vibration Technology); Counterweight mechanism + Damper spring *4 Europe, rth America:, Australia, Brazil: 2.0 (6.6), Other countries: 2.5 (8.2), *5 with side grip 0-1,150 Capacities: 0-1, 0-4,500 / 2.9 (6.4) 0-1,/ 0-1,/ 1, 0-4,500/ 0-4,500/ 4,500 86 N/A 30 (1-3/16) 0-0 0-4,000 15.0 (18.5*2) 91 (92*2) / 380 (15) 84 (3-5/16) 210 (8-1/4) 2.9 (6.4) 50 (2) 12.7 (20.0*2) 92 (91*2) 351 (13-3/4) 73 (2-7/8) 198 (7-3/4) 5.0 (16.4) 2.8 (6.2)
Comparison of products P 6/ 6 Comparison Continuous rating input: W Rated amperage for rth America: A load speed: min ¹= rpm Impacts per minute= min ¹ Chuck type Impact energy (EPTA): J 2.4 Operation mode: R= Rotation only R+H= Rotation with Hammering Vibration: m/s² ise: db(a) TCT bit Rotation reversing facility Variable speed control LED Job light Power supply cord: m (ft) Weight according to EPTA- Procedure 01/2003*7: kg(lbs) HR2610T/ HR2611FT Concrete Steel Wood Core bit Diamond core bit 0-1,200 H= Hammering only Quick change drill chuck Vibration absorption / (AVT*3) Dimensions: Model and Round shank bits*1 15.0/ 11.5 91/ / / / Length 385 (15-1/8) 394 (15-1/2) 384 (15-1/8) Length*5 421 (16-1/2) Width 77 (3) 84 (3-1/4) Height 209 (8-1/4) 214 (8-3/8) 204 (8) *6 2.9/ 3.0 (6.4/ 6.6) Makita BOSCH HITACHI HILTI HR2470T/ HR2470FT HR2450T/ HR2450FT GBH2-26DFR DH24PM TE2-M 650 N/A 22 (7/8) 50 (2) 30 (1-3/16) 20 (13/16) 0-1, 0-1, 0-0 0-1,150 0-1,200/ 0-2,500 0-4,500 0-4,500 0-4,000 Capacities: 2.4 3.0 () 2.1 86 2.9 (6.5) and Round shank bits*1 2.5*4 15.0 91 407 (16) 84 (3-5/16) 210 (8-1/4) 3.0 () Impact energy*2: J 2.9 2.7 2.7 3.0 3.2 1.8 10.2 384 (15-1/8) 5.0 (16.4) 2 modes (R/ R+H) 10.0 (14.0*4) 89 (88*4) 352 (13-7/8) 422 (16-5/8) 431 (17) 433 (17) N/A N/A 73 (2-7/8) 198 (7-3/4) 89 (3-1/2) 203 (8) 3.0 (6.5) *1 Round shank bits can also be used by replacing the factory-mounted chuck with Quick change drill chuck (keyless), *2 Measured according to our conventional reference, *3 AVT (Anti Vibration Technology); Counterweight mechanism + Damper spring, *4 Actually measured value, *5 with Quick change drill chuck, *6 Europe, rth America:, Australia, Brazil: 2.0 (6.6), Other countries: 2.5 (8.2), *7 with side grip