1'-0" ± TYP. S 10'-0" MAX. 2'-0" MAX. WINCH 2" O.D. TOP STEEL TUBE IN FABRIC POCKET 2-3/8" O.D. STEEL DRIVE PIPE 12" MIN. DRIVE BELT ROLLED ONTO DRIVE PIPE JOIST OR TRUSS BOTTOM CHORD, SUPPORT TUBE OR BEAM (BY OTHERS) VINYL MESH COLOR = 3-1/2" O.D. BOTTOM STEEL TUBE. ROLLED INTO VINYL AND SECURED WITH ALUMINUM STRIP. 18OZ. SOLID VINYL HEIGHT 8'-0" STANDARD OR SPECIFY = COLOR = STRUCTURE ELEVATION = (BOTTOM OF ATTACHMENT POINT TO FINISHED FLOOR) 5'-0" BELTS 20'-0" MAX. BELTS 20'-0" MAX. 5'-0" 3'-0" RECOMMENDED SPACE TO NEAREST OBJECT CURTAIN LENGTH = 3'-0" RECOMMENDED SPACE TO NEAREST OBJECT DIVIDER CURTAIN ROLL-UP ARIZONA COURTLINES, INC. 8742 NORTH 78TH AVENUE, PEORIA, ARIZONA 85345 TEL. 623.939.8126 FAX. 623.939.2526 EDDIE CAFFERATA QUANTITY:
CENTER LINE OF CURTAIN OPEN WEB STEEL JOIST BOTTOM CHORD SHOWN BOTTOM OF SUPPORT STRUCTURE 3-1/2" SUPPORT TUBE DRIVE PIPE 2'-1 1/4" 11" FABRIC BOTTOM OF FABRIC THESE DIMENSIONS ARE PROVIDED AS A GUIDELINE ONLY. FINAL INSTALLED DIMENSIONS MAY VARY. -CLR ROLL-UP GYM DIVIDER CURTAIN ROLLED CLEARANCE ARIZONA COURTLINES, INC. 8742 NORTH 78TH AVENUE, PEORIA, ARIZONA 85345 TEL. 623.939.8126 FAX. 623.939.2526 EDDIE CAFFERATA QUANTITY:
14-5/16" MOTOR TOP VIEW 1" DIA. X 2-1/4" L SHAFT (TYP. 2) MOUNTING PLATE WIRING BOX 3-1/8" MOTOR SHAFT 16-3/16" MOUTNING PLATE ISO VIEW SHAFT 2-1/8" SIDE VIEW WIRING BOX MOUNTING PLATE MOTOR CURTAIN WINCH SPECIFICATIONS Drive shaft can be run off one or both sides 5" Lightweight unit weighs only 47 pounds Instantly reversing 3/4 HP motor (115V, 8.5 FLA, PH-1) is governed to stall at 14 amps to prevent overload Hardened steel worm gear is captured to take on radial and thrust loads. Our winch is specified to continuously run at the maximum rated load of 1250 lbs for the motors rated duty cycle of 20 minutes without sustaining any gear damage 9-15/16" WIRING BOX SHAFT Motor develops over 2,300 inch pounds of torque at 8 rpm, or 9.5 feet per minute at 1,000 pounds High-strength steel alloy output shafts provide a standard 1-inch keyed interface, allowing flexibility with multiple types of existing couplers and installations Sealed gear case uses precision ball bearings and premium seals for superior performance and a lifetime of maintenance-free operation Electric limit switches for consistant stopping in & up down positions. Electrician to hardware at wiring box CURTAIN CENTERLINE 6-7/16" 16-3/16" 9-3/4" DIVIDER CURTAIN WINCH CHECKED BY: DC-WINCH FOR ALL TYPES OF ELECTRIC DIVIDER CURTAINS 8742 NORTH 78TH AVENUE PEORIA, ARIZONA 85345 TEL. 623.939.8126 FAX. 623.939.2526 QUANTITY:
SUPPORT PIPE (3-1/2" TYP.) SUPPORT PIPE (3-1/2" TYP.) 1/2" ALL THREAD (16" TYP.) 7-1/2" 3-1/2" HALF CLAMP 1/2" ALL THREAD (16" TYP.) 3/16" S-HOOK (INSTALLER CRIMP) 3/16" CHAIN (14" TYP.) 3/16" S-HOOK (INSTALLER CRIMP) 1/2" SERRATED FLANGE NUT 2" UPPER CURTAIN PIPE (INSIDE POCKET) 2" UPPER CURTAIN PIPE (INSIDE POCKET) INSTALLER CUT SMALL VERTICAL SLIT IN UPPER CURTAIN POCKET FOR CHAIN CURTAIN FABRIC INSTALLER CUT SMALL VERTICAL SLIT IN UPPER CURTAIN POCKET FOR CHAIN 3/16" CHAIN (14" TYP.) CURTAIN FABRIC DIVIDER CURTAIN CHECKED BY: DC- DETAIL (ROLL-UP & UP-FOLD) 8742 NORTH 78TH AVENUE PEORIA, ARIZONA 85345 TEL. 623.939.8126 FAX. 623.939.2526 QUANTITY:
BELT WRAPPED AROUND DRIVE PIPE BELT WRAPPED AROUND DRIVE PIPE ATTACH BELT TO DRIVE PIPE W/ 3 SELF-TAPPING SCREWS. THEN WRAP BELT 3 TIMES. SEE WINCH INSTRUCTIONS FOR WRAP DIRECTION BELT OVER TOP OF 2" PIPE FABRIC POCKET 2" UPPER CURTAIN PIPE FABRIC POCKET 2" UPPER CURTAIN PIPE IN FABRIC POCKET 1/4" LOCK NUT (2 PER BELT) 2" UPPER CURTAIN PIPE CURTAIN FABRIC 1/4" X 1-1/2" BOLT (2 PER BELT) LARGE WASHER (4 PER BELT) 1/4" HARDWARE FABRIC SELF-TAPPING SCREWS (NOT TO EXCEED 12" ON CENTER) ALUMINUM STRIP ALUMINUM STRIP (LENGTH OF CURTAIN) BELT UNDER FABRIC COVERED 3-1/2" PIPE FABRIC ROLLED ONTO BELT UNDER FABRIC COVERED 3-1/2" PIPE FABRIC ROLLED ONTO ROLL-UP DIVIDER CURTAIN DCRU-2.2 BELT ROUTING DETAIL ARIZONA COURTLINES, INC. 8742 NORTH 78TH AVENUE, PEORIA, ARIZONA 85345 TEL. 623.939.8126 FAX. 623.939.2526 EDDIE CAFFERATA QUANTITY:
ARIZONA COURTLINES, INC. SPECIFICATIONS (ACI MODEL #) DIVIDER CURTAIN - ROLL-UP DRIVE SYSTEM Drive pipe shall be 2 3/8" tubing which extends the entire length of the curtain. Drive pipe supports shall not exceed 10'-0" on center. Belts are 4" wide polyurethane (1700lbs. Per inch tensile strength). Belt shall attach to the upper curtain support (2 3/8" diameter tubing) loop around lower curtain support (Rolling Batten 3 1/2" diameter tubing) and up to a 5" drum located on drive shaft. Belt drums shall be located on drive shaft approximately every 20'-0". Bottom of curtain is rolled around the 3 1/2" tubing and held in place with an aluminum stop strip, which run the entire length of the curtain. ELECTRIC MOTOR Electric operator shall hold the divider curtain at any position when raising or lowering including in the event of a power failure. Worm gear set shall be in a sealed oil case. High quality rollers, bearings and bushings are used for exceptional wearability and long life characteristics. Motor shall have automatic overload protection, with 3-wire control system for dependable energy saving power. Winch shall be operated by a keyed up and down momentary contact control switch. All conduit, wiring, junction boxes and components not listed here shall be furnished and installed by the electrical contractor. Motor Specifications: H.P. 1.0 - RPM 1725 - Hz. 60 - V 115 - Duty: Cont. - F.L.A. 12.8 - S.F.A. 13.6. UPPER CURTAIN (NETTING) The upper section of the curtain is made from mesh woven vinyl and polyester netting, with a 4" wide solid vinyl strip. These 4" wide solid vinyl strips make this curtain extremely durable. Woven mesh material shall have a certificate of flame resistance from the State of California. LOWER CURTAIN (SOLID) The lower solid vinyl section of the divider curtain shall extend 10 feet above ground. Vinyl cover shall be 22oz per square yd. vinyl coated polyester with 1000-denier polyester base fabric. Solid vinyl material shall have a certificate of flame resistance from the State of California (Registered fabric No. 140.01). See ACI Color Chart for available colors.