STAINLESS STEEL SYSTEMS

STAINLESS STEEL SYSTEMS 139

Systems Table of Contents Figure 472 Rigid Couplings Page 142 Figure 401 45 Elbows Page 149 Figure SS-7X Rigid Couplings (Large Diameter) Page 143 Figure 405 Flexible Couplings Page 144 SS-8X Heavy Duty Flexible Coupling Page 145 SS-1200 High Pressure Flexible Couplings Page 146 Figure 705R Rilsan Coated Flexible Coupling Page 147 SS-28 Hinged Lever Coupling Page 148 Figure 419 Tees Page 150 Figure 460 End Caps Page 151 Figure 421 Reducing Tees Page 152 Figure 450 Concentric Reducers Page 153 Figure SJ-400 Butterfly Valve Pages 156-157 Figure SJ-600L Ball Valve Page 158 Figure SJ-600W Ball Valve Page 159 Figure SS-41 Flange Adapters (ANSI Class 150#) Page 154 Figure SJ-630 Three Port Ball Valve Page 160 Figure 443 & 444 Flange Adapters (PN16/PN10 BS 4504) Page 155 Figure SJ-726 Y Strainer Page 161 Figure 410 90 Elbows Page 149 Figure SS-723 Mechanical Tee Page 162 General notes: Additional information is included in our data sheets and is available upon request. It is the Designer s responsibility to select products suitable for the intended service and to ensure that pressure ratings and performance data is not exceeded. Always read and understand the installation constructions. Never remove any piping components nor correct or modify any piping deficiencies without first depressurizing and draining the system. Material and gasket selection should be verified with the gasket recoendation listing for the specific application. 140 GRINNELL reserves the right to change the contents without notice. www.grinnell.com

Coupling Specifications MATERIAL SPECIFICATIONS Housing Specifications specification for castings, iron-chromium, for general application Grade CR-8M. (70,000 psi) (30,000 psi) (2") minimum 30% Bolt/Nut Specifications conforming to ASTM A 193M Class 2, Type 316 Grade B8M conforming to ASTM A 194M, Type 316, Grade 8M * Shurjoint product specifications can be found at www.shurjoint.com Gasket Specifications gaskets have a Green colour code stripe identification and conform to ASTM D 2000 for service temperatures from -34 C to 110 C (-30 F to 230 F). They are recoended for hot water not to exceed 110 C (230 F) plus a variety of dilute acids, oil free air, and many chemical services. They are not recoended for petroleum services. gaskets have a Yellow and Green colour code stripe identification and are NSF- 61 approved for cold and hot portable water up to 82 C (180 F). gaskets have an Orange colour code stripe identification and conform to ASTM D 2000 for service temperatures from -29 C to 82 C (-20 F to 180 F). They are recoended for petroleum products, vegetable oils, mineral oils, and air with oil vapors. gaskets are Red colour code stripe and conform to ASTM D 2000 for service temperatures from -34 C to 177 C (-30 F to 350 F). They are recoended for air without hydrocarbons, or dry heat. gaskets have a Blue colour code stripe and conform to ASTM D 2000. They are recoended for oxidizing acids, petroleum products, hydraulic fluids, lubricants, and halogenated hydrocarbons. MATERIAL SPECIFICATIONS ASTM A 312, Schedule 10 and Schedule 40 ASTM A 403 WPW or A 403 CR steel fittings are" 4.0 (0.16") for 250 to 300 (10" and 12"). Fittings are fabricated from SS316Ti / 1.4571 Fitting Specifications Tech Data Sheet: G570 Fittings are available in full-flow and fabricated versions in 304 and 316L S.S. Fabricated fittings are available with Schedule 10 or Schedule 40 wall thickness. For pressure ratings of fittings, refer to data sheet G570. For detailed Listing / Approval information contact GRINNELL Mechanical Products For local country potable water approvals, contact a GRINNELL Sales Representative. Refer to back cover for country-specific contact information 141

Figure 472 Rigid Couplings Tech Data Sheet: G560 The GRINNELL Figure 472 Rigid Coupling is made of cast 316L stainless steel and is capable of pressure up to 41.4 Bar (600 psi). The GRINNELL Figure 472 Patented Coupling universal tongueand-groove design allows the housing to grip along the full 360 of circumference of the pipe. Sizes 32 100 (1 1 4" 4") have gripping teeth to prevent rotation during installation. B C A Part Number 472MD00424 472MD00484 472MD00604 472MD00734 472MD00764 472MD00894 472MD01144 472MD01394 Max. Pressures Bar psi Max. End Load kn Max.* End Gap A Dimensions B C Coupling Bolts Size** 32 42.4 41.4 5.78 1.5 69.9 111.3 46.0 M10 x 57 0.9 40 48.3 41.4 7.57 2.0 76.2 117.3 46.0 M10 x 57 1.0 50 60.3 41.4 11.82 3.3 86.6 130.0 47.8 M10 x 57 0.9 65 73.0 41.4 17.32 3.3 99.3 143.0 47.8 M10 x 57 1.5 65 76.1 41.4 18.86 3.3 106.4 145.3 50.8 M10 x 57 1.6 80 88.9 41.4 25.68 3.3 117.6 158.8 47.8 M12 x 89 1.6 100 114.3 41.4 42.44 4.8 147.6 190.5 50.0 M12 x 89 2.5 125 139.7 41.4 63.40 4.8 178.3 246.9 52.3 M16 x 83 3.9 472MD01414 472MD01684 472MD02194 472MD02734 472MD03244 125 141.3 41.4 64.87 4.8 180.1 246.6 51.8 M16 x 83 3.9 150 168.3 41.4 92.00 4.8 205.5 267.5 54.1 M16 x 83 4.3 200 219.1 41.4 155.92 4.8 268.2 344.4 66.5 M20 x 121 8.8 250 273.0 41.4 242.22 3.3 326.1 416.8 66.5 14.5 300 323.9 41.4 340.73 3.3 391.4 478.5 66.5 19.5 Figure 472 Rigid Couplings have an Anti-Rotation Feature of gripping teeth along the coupling keys in sizes 1 1 4" - 4" (32-100 ), making the Figure 472 perfectly suited for installations where the likelihood of rotation is greatest. * Maximum available gap between pipe ends. Minimum gap = 0. Maximum Pressure and End Load are total from all loads based on standard weight stainless steel pipe. Pressure ratings and end loads may differ for other pipe materials and/or wall thickness. Contact a GRINNELL Sales Representative for details. Max end gap is for cut grooved standard weight stainless steel pipe. Values for roll grooved pipe will be half that of cut grooved. ** Contact a GRINNELL Sales Representative for availability of inch bolt sizes vs. metric bolt sizes. See page 141 for stainless steel coupling specifications and pages 234-245 for gasket information. Refer to pressure ratings for Schedule 5, 10, and 40 pipe on pages 262-265, or contact a GRINNELL Sales Representative. Note: The Fig. 472 Heavy Duty Rigid Coupling does not provide compensation for pipe system expansion and/or contraction associated with pipe system temperature changes. 142 GRINNELL reserves the right to change the contents without notice. www.grinnell.com

) ) ) ' ( The Shurjoint Model SS-7X is a tongue and groove rigid coupling designed to provide a rigid joint for stainless steel pipe in sizes 250 to 600 (10 to 24 ). The SS-7X is supplied standard in CF8 (304) and CF8M (316) with 304 and 316 bolts and nuts. The bolts must be fastened to the required torque for proper installation. Shurjoint Figure SS-7X Rigid Couplings (Large Diameter) Shurjoint Tech Data Sheet: K-02 Pressure-Temperature Rating Nom. Rating Class 150 Working Pressure (S40S, Roll-grooved) 20 Bar @38 C Max. Service Temperature EPDM: 110 C! Nitrile: 82 C " # $ % &! * The working pressure shown is based on roll-grooved Sch. 10S pipe. For other pipe schedules and cut-grooved pipe, see page 76 Performance Data Sheet. * Proof test pressure: 1.5 times the working pressure, non-shock cold water. * Burst pressure is engineered minimum 2 times the working pressure. ' ( ' ( Size 250 350 (10" 14") 400 450 (16" 18") 500 600 (20" 24") Pipe O. D. Pipe End Separation Dimensions - Bolt Size A B C No. in 250 273.0 0-3.2 318 406 65 2 10.5 300 323.9 0-3.2 374 452 65 2 11.5 350 355.6 0-3.2 397 500 75 2 15.0 400 406.4 0-3.2 461 536 75 6 19.4 450 457.2 0-3.2 514 587 75 6 25.0 500 508.0 0-3.2 571 669 79 8 33.1 550 558.8 0-3.2 622 720 79 8 33.0 600 609.6 0-3.2 673 771 79 8 34.7 Refer to the Shurjoint technical data sheet for complete technical information and installation instructions. More information about Shurjoint Piping Products can be found on page 14 in the General Data section of this book or on www.shurjoint.com. See page 141 for stainless steel coupling specifications. Refer to back cover for country-specific contact information 143

Figure 405 Flexible Couplings Tech Data Sheet: G565 The GRINNELL Figure 405 Flexible Coupling is made of 316L stainless steel and is capable of pressures up to 51.7 Bar (750 psi), depending on pipe size and wall thickness. B C A Part Number 405MD00344 405MD00424 405MD00484 405MD00604 405MD00734 405MD00764 405MD00894 405MD01144 405MD01394 Max. Pressures Bar psi Max. End Load kn Max.* End Gap Deflection Degrees per coupling /m In/Ft A Dimensions B C Coupling Bolts Size** (Qty. 2) 25 33.7 51.7 4.53 3.3 95.1 56.0 97.0 46.0 M10 x 57 0.6 5 26' 32 42.4 51.7 7.22 3.3 75.0 65.0 106.4 46.0 M10 x 57 0.7 4 19' 40 48.3 51.7 9.46 3.3 65.8 69.9 112.8 46.0 M10 x 57 0.7 3 46' 50 60.3 34.5 9.85 3.3 52.5 82.6 124.0 47.8 M10 x 57 0.8 3 1' 65 73.0 34.5 14.44 3.3 43.3 93.7 139.7 47.8 M10 x 57 0.9 2 29' 65 76.1 34.5 15.72 3.3 41.7 101.6 146.10 47.8 M12 x 89 1.4 2 23' 80 88.9 34.5 21.40 3.3 35.8 111.3 165.1 47.8 M12 x 89 1.4 2 3' 100 114.3 22.4 22.99 6.4 55.8 144.5 196.9 52.3 M12 x 89 1.8 3 11' 125 139.7 13.8 21.13 6.4 45.5 173.0 247.7 52.3 M16 x 83 3.3 2 36' 144 405MD01414 405MD01684 405MD02194 125 141.3 13.8 21.62 6.4 45.0 174.8 247.7 52.3 M16 x 83 3.2 2 35' 150 168.3 13.8 30.67 6.4 37.5 201.7 271.5 52.3 M16 x 83 3.2 2 10' 200 219.1 13.8 51.97 6.4 29.2 258.8 344.4 63.5 M20 x 121 6.6 1 40' Values for roll grooved pipe will be half that of cut grooved. * Maximum available gap between pipe ends. Minimum gap = 0. Maximum Pressure and end load are total from all loads based on standard weight stainless steel pipe. Pressure ratings and end loads may differ for other pipe materials and/or wall thickness. Contact a GRINNELL Sales Representative for details. Max End Gap and Deflection is for cut grooved standard weight stainless steel pipe. ** Contact a GRINNELL Sales Representative for availability of inch bolt sizes vs. metric bolt sizes. See page 141 for stainless steel coupling specifications and pages 234-245 for gasket information. For fire protection equipment listing and approval pressure ratings contact Tyco FPP. Refer to pressure ratings for Schedule 5, 10, and 40 pipe on pages 262-265, or contact a GRINNELL Sales Representative. GRINNELL reserves the right to change the contents without notice. www.grinnell.com

The Shurjoint Model SS-8X is designed for high pressure applications including reverse osmosis and desalination systems. The SS-8X is available in Duplex CD3MN (2205), Super Duplex CE8MN, CE3MN (2507) and 6-Moly stainless steel CK3MCuN (254SMO*). The SS-8X features 316 bolts, washers and Silicon Bronze nuts to help prevent galling during repetitive use. The SS-8X is also available in CF8M (316) with 316 bolts and nuts. contact GRINNELL for details. * 254SMO is a registered trademark of AvestaPolarit AB. Shurjoint SS-8X Heavy Duty Flexible Coupling Shurjoint Tech Data Sheet: K-04 Pressure-Temperature Rating Size Nom. Rating 20-100 - - CWP 125-200 - - CWP Working Pressure (S40S, Cut-grooved) 97 Bar @38 C 70 Bar @38 C Test Pressure (Hydrostatic) 145 Bar 103 Bar Max. Service Temperature EPDM: 110 C! Nitrile: 82 C " # $ % &! 0. / *Working pressure is based on cut-grooved Sch. 40S or 80S pipe only. *Burst pressure is engineered minimum 2 times the working pressure. Size Pipe O. D. Pipe End Separation A Dimensions B C Deflection Degree ( ) Bolt Size 20 26.9 0-1.6 56.0 95.0 46.0 3-23 0.7 25 33.7 0-1.6 63.0 99.0 46.0 2-45 0.8 32 42.4 0-1.6 72.0 111.0 46.0 2-10 0.9 40 48.3 0-1.6 78.0 123.0 46.0 1-54 1.0 50 60.3 0-1.6 88.0 134.0 47.0 1-31 1.2 65 73.0 0-1.6 153.0 103.0 47.0 1-15 1.3 80 88.9 0-1.6 120.0 171.0 47.0 1-02 1.8 100 114.3 0-3.2 152.0 201.0 52.0 1-36 2.4 125 141.3 0-3.2 181.0 249.0 53.0 1-18 3.5 150 168.3 0-3.2 208.0 276.0 53.0 1-05 4.0 200 219.1 0-3.2 267.0 341.0 62.0 0-50 6.8 * +, 216.3 0-3.2 264.0 338.0 62.0 0-51 6.5 Working pressure ratings are based upon generally accepted pressure piping design standards and testing in accordance with ASME Section VIII Division 1 pressure vessel test methods. Refer to the Shurjoint technical data sheet for complete technical information and installation instructions. More information about Shurjoint Piping Products can be found on page 14 in the General Data section of this book or on www.shurjoint.com. See page 141 for stainless steel coupling specifications. Refer to back cover for country-specific contact information 145

1 Shurjoint SS-1200 High Pressure Flexible Couplings Shurjoint Tech Data Sheet: K-17 Housings: A890 Grade 5A Grade 4A 2 3 The Shurjoint Model SS-1200 is designed for high pressure applications including reverse osmosis, desalination and other specialty systems. The SS-1200 is available in strong and anti-corrosive alloys of Duplex CD3MN (2205), Super Duplex CE8MN, CE3MN (2507) and 6-Moly stainless steel CK3MCuN (254SMO*). The SS-1200 features 316 bolts, washers and Silicon Bronze nuts to help prevent galling during repetitive use. The Fast-Fit gasket has been designed and engineered for easier and faster installations. The pipe-end friendly design eliminates struggling to stretch the gasket over the pipe ends and the Fast-Fit gasket also features Shurjoint s Gap-Seal technology, which seals the gap between the pipe ends and eliminates stagnant water pockets within the gasket cavity. The Fast-Fit gasket is UL classified in accordance with ANSI/ NSF 61 for potable water (Cold Water 30 C (86 F) / and Hot Water 82 C (180 F). Always use the factory supplied Shurjoint Fast-Fit gasket. Performance standards do not support the use of a standard gasket in the SS-1200 coupling. * 254SMO is a registered trademark of AvestaPolarit AB. Pressure-Temperature Rating Nom. Rating CWP Working Pressure (S40S, Roll-grooved) 84 Bar @38 C Test Pressure (Hydrostatic) 126 Bar Max. Service Temperature EPDM: 110 C! Nitrile: 82 C " # $ % &! *Working pressure is based on cut-grooved Sch. 40S or 80S pipe only. *Burst pressure is engineered minimum 2 times the working pressure. Fast-Fit Gasket: Easy installation with a single hand Always use the Fast-fit gasket. Don't use a standard gasket with the SS-1200 coupling. Pipe End Separation Dimensions - A B C Deflection Degree ( ) Coupling Bolt Size (Qty 2) Approx 20 26.9 0-1.6 53 94 46 3-23 0.45 25 33.7 0-1.6 60 101 46 2-45 0.55 32 42.4 0-1.6 70 111 46 2-10 0.63 40 48.3 0-1.6 76 117 46 1-54 0.70 50 60.3 0-1.6 88 137 49 1-31 1.04 65 73.0 0-1.6 102 151 49 1-15 1.38 80 88.9 0-1.6 119 168 49 1-02 1.55 100 114.3 0-3.2 152 207 52 1-36 2.13 Working pressure ratings are based upon generally accepted pressure piping design standards and testing in accordance with ASME Section VIII Division 1 pressure vessel test methods. Refer to the Shurjoint technical data sheet for complete technical information and installation instructions. More information about Shurjoint Piping Products can be found on page 14 in the General Data section of this book or on www.shurjoint.com. See page 141 for stainless steel coupling specifications. 146 GRINNELL reserves the right to change the contents without notice. www.grinnell.com

) Figure 705R Rilsan Coated Flexible Coupling ' ( Part Number 705MES042R 705MES048R 705MES060R 705MES076R 705MES089R 705MES114R 705MES139R 705MES141R 705MES165R 705MES168R 705MES219R Max. Wk Pressure Bar Psi Max. End Load kn Lbs Max. End Separation Deflection Dimensions Coupling Bolt Size Pipe A B C (Qty 2) /m in/ft Per Coupling Degrees Approx 32 42.4 16.0 2.21 3.3 75.0 65 106 46 0.7 4 19' M10x60 40 48.3 16.0 2.90 3.3 65.8 70 113 46 0.7 3 46' M10x60 50 60.3 16.0 4.53 3.3 52.5 83 124 48 0.8 3 01' M10x60 65 76.1 16.0 7.23 3.3 41.7 102 146 48 1.4 2 23' M12x80 80 88.9 16.0 9.84 3.3 35.8 111 165 48 1.4 2 03' M12x80 100 114.3 16.0 16.27 6.4 55.8 145 197 52 1.8 3 11' M12x80 125 139.7 16.0 24.31 6.4 45.0 173 248 52 3.3 2 36' M16x90 125 141.3 16.0 24.87 6.4 45.0 175 248 52 3.2 2 35' M16x90 150 165.1 16.0 33.95 6.4 38.3 197 272 52 3.2 2 12' M16x90 150 168.3 16.0 35.27 6.4 37.5 202 272 52 3.2 2 10' M16x90 200 219.1 16.0 59.78 6.4 29.2 259 344 64 6.6 1 40' M20x120 : Maximum pressure and end load are total from all loads based on standard weight steel pipe. Pressure ratings and end loads may differ on pipe materials and/or wall thickness. Contact a GRINNELL Sales Representative for details. For fire protection equipment listing and approval pressure ratings contact a GRINNELL Sales Representative.. : Maximum pipe end separation is for cut grooved standard weight pipe. Values for roll grooved will be 1 2 that of cut grooved. Standard 316 Bolt, Nuts and Washer. Standard 316 Bolt, Nuts and Washer. Always use washers in combination with Fig 705R Rilsan Coated Couplings Because of the Rilsan coating FM/UL/VDS/LPC approvals do not apply. Also available with zinc plated bolts and nuts. Part code: 705ME...R (e.g. 705ME114R) See page 141 for stainless steel coupling specifications. Refer to back cover for country-specific contact information 147

' = ( Shurjoint SS-28 Hinged Lever Coupling Shurjoint Tech Data Sheet: K-21 Locking Lever Handle: A 743 Gr. CF8 Toggle Links, Hinge Pin, & Rivet: Split Pin: Pressure-Temperature Rating Nom. Rating Class 150 Working Pressure (STD, Roll-grooved) 20 Bar @38 C Max. Service Temperature EPDM: 110 C! Nitrile: 82 C " # $ % &! *Working pressure is based on cut-grooved Sch. 40S or 80S pipe only. *Burst pressure is engineered minimum 2 times the working pressure. The Shurjoint Model SS-28 Hinged Grooved Coupling is designed for quick connect and disconnect services. The housing segments are hinged with a lever handle for easy assembly. Use of the split pin can prevent the accidental opening of the coupling. The Model SS-28 can be used in a wide variety of applications with standard roll- or cut- grooved pipe. Housings 40-100 (1 1 2-4 ) feature a smooth outer surface, housings 125-300 (5-12 ) feature a cross-ribbed design for added strength. Standard gasket: Grade E EPDM or Grade T Nitrile. Available standard in CF8 (304) or CF8M (316). Expansion Pipe Lever handles are factory assembled tight for safety. The use of an expansion pipe will aid the easy opening and closing. Expansion pipes are available upon request. 6 7 8 9 : ; 9 < 6 7 8 9 : ; 9 < Max. Working Pressure Bar PSI Axial Displacement Dimensions - A B C Deflection Degree ( ) 40 48.3 20 0 1.6 75 118 47 4 5 1.0 50 60.3 20 0 1.6 86 121 48 4 5 1.1 65 73.0 20 0 1.6 92 150 48 4 5 1.4 65 76.1 20 0 1.6 92 150 48 4 5 1.4 80 88.9 20 0 1.6 119 163 48 4 5 1.8 100 114.3 20 0 3.2 165 205 52 4 5 2.7 125 139.7 20 0 3.2 189 253 52 4 5 4.9 125 141.3 20 0 3.2 189 253 52 4 5 4.9 150 165.1 20 0 3.2 213 278 52 4 5 5.8 150 168.3 20 0 3.2 216 281 52 4 5 5.8 *Deflection or angular movement is the maximum value that a coupling allows under no internal pressure. Refer to the Shurjoint technical data sheet for complete technical information and installation instructions. More information about Shurjoint Piping Products can be found on page 14 in the General Data section of this book or on www.shurjoint.com. See page 141 for stainless steel coupling specifications. 148 GRINNELL reserves the right to change the contents without notice. www.grinnell.com

@ ) A ' ( The Shurjoint Model SS-41 stainless steel flange adapter allows for a direct connection with ANSI Class 125/150 flanges. The SS-41 is investment cast in Gr. CF8 (304) or CF8M (316). Integral closure tabs located on the flange OD help facilitate alignment and assembly. Shurjoint Figure SS-41 Flange Adapters (ANSI Class 150#) Shurjoint Tech Data Sheet: K-08 MATERIAL SPECIFICATIONS Fitting Body: A743 Gr. CF8 Pressure-Temperature Rating Nom. Rating Working Pressure (S40S, Roll-grooved) > %? 20 Bar @38 C Max. Service Temperature EPDM: 110 C! Nitrile: 82 C " # $ % &! pipe. Apply 110% for cut-grooved Sch. 40S pipe. Apply 80% for roll-grooved Sch. 10S pipe and 50% for roll-grooved Sch. 5S pipe. water. Max. Working Pressure Bar psi Max. End Load kn A Dimensions Sealing Surface Bolts B C D E 50 60.3 20 5.71 152 121 21 60 87 5 8 x 3 2.1 4 65 73.0 20 8.37 178 140 22 73 102 5 8 x 3 2.7 4 80 88.9 20 12.41 190 152 24 89 116 5 8 x 3 3.1 4 100 114.3 20 20.51 229 191 24 114 141 5 8 x 3 4.5 8 150 168.3 20 44.47 279 241 25 168 198 3 4 x 3 1 2 5.8 8 200 219.1 20 75.37 343 298 28 219 254 3 4 x 3 1 2 9.2 8 No. Size. in * Based on Sch. 10S pipe. Refer to the Shurjoint technical data sheet for complete technical information and installation instructions. More information about Shurjoint Piping Products can be found on page 14 in the General Data section of this book or on www.shurjoint.com. See page 141 for stainless steel coupling specifications. See pages 44-45 for flange washer Adaptor and page 267 flange drilling specifications Refer to back cover for country-specific contact information 149

Figure 443 & 444 Flange Adapters (PN16/PN10 BS 4504) Tech Data Sheet: G568 A : B A Figure 443 - PN16 Figure 444 - PN10 BS 4504 Part Number E to E 32 42.4 90 M16 x 65 1.8 443H000424 4 40 48.3 92 M16 x 65 2.0 443H000484 4 50 60.3 95 M16 x 65 2.7 443H000604 4 Mating Flange Bolt E to E Mating Flange Bolt Part Number Qty. Size * Qty. Size * 65 76.1 95 M16 x 65 3.3 443H000764 4 80 88.9 100 M16 x 70 4.0 443H000894 8 100 114.3 102 M16 x 70 4.6 443H001144 8 125 139.7 105 M16 x 75 6.0 443H001394 8 150 168.3 105 M20 x 80 7.2 443H001684 8 200 219.1 112.0 M20 x 80 10.2 444H002194 8 250 273.0 138.0 M20 x 90 18.0 444H002734 12 300 323.9 138.0 M20 x 90 22.4 444H003244 12 * = Bolts are not supplied. Bolt lengths shown are standard; it is the responsibility of the purchaser to verify correct lengths for intended applications Schedule 40 fittings available upon request, contact a GRINNELL Sales Representative. See pages 44-45 for flange washer Adaptor and page 267 flange drilling specifications See page 141 for stainless steel specifications. 150 GRINNELL reserves the right to change the contents without notice. www.grinnell.com

( Figure 410 90 Elbows Tech Data Sheet: G570 Figure 401 45 Elbows Tech Data Sheet: G570 C D E F : B A Part Number 410H000344 C to E 25 33.7 73.0 0.5 Part Number 401H000344 C to E 25 33.7 50.0 0.5 410H000424 410H000484 410H000604 32 42.4 83.0 0.5 40 48.3 92.0 0.5 50 60.3 111.0 0.9 401H000424 401H000484 401H000604 32 42.4 54.0 0.5 40 48.3 58.0 0.5 50 60.3 65.0 0.9 410H000764 65 76.1 130.0 1.4 401H000764 65 76.1 73.0 1.4 410H000894 80 88.9 149.0 2.0 401H000894 80 88.9 80.0 2.0 410H001144 100 114.3 187.0 3.9 401H001144 100 114.3 95.0 3.9 410H001394 125 139.7 225.0 6.1 401H001394 125 139.7 110.0 6.1 410H001684 150 168.3 263.0 8.4 401H001684 150 168.3 125.0 8.4 410H002194 200 219.1 345.0 16.6 401H002194 200 219.1 160.0 16.6 410H002734 250 273.0 421.0 27.2 401H002734 250 273.0 190.0 27.2 410H003244 300 323.9 437.0 30.4 401H003244 300 323.9 220.0 30.4 For information on alternative sizes, contact a GRINNELL Sales Representative. Schedule 40 fittings available upon request, contact a GRINNELL Sales Representative. See page 141 for stainless steel fitting specifications. For instructions on part numbers, ordering information, and availability, refer to page 15 or contact a GRINNELL Sales Representative. For information on alternative sizes, contact a GRINNELL Sales Representative. Schedule 40 fittings available upon request, contact a GRINNELL Sales Representative. See page 141 for stainless steel fitting specifications. For instructions on part numbers, ordering information, and availability, refer to page 15 or contact a GRINNELL Sales Representative. Refer to back cover for country-specific contact information 151

Figure 419 Tees Tech Data Sheet: G570 Part Number 419H000344 C to E 25 33.7 73.0 0.5 G H I J 419H000424 419H000484 419H000604 32 42.4 60.0 0.5 40 48.3 62.0 0.5 50 60.3 68.0 0.9 G H I J 419H000764 419H000894 419H001144 419H001394 419H001684 419H002194 419H002734 419H003244 65 76.1 76.0 1.4 80 88.9 86.0 2.0 100 114.3 105.0 3.9 125 139.7 160.0 6.1 150 168.3 178.0 8.4 200 219.1 218.0 16.6 250 273.0 256.0 27.2 300 323.9 294.0 30.4 Schedule 40 fittings available upon request, contact a GRINNELL Sales Representative. See page 141 for stainless steel fitting specifications. For instructions on part numbers, ordering information, and availability, refer to page 15 or contact a GRINNELL Sales Representative. 152 GRINNELL reserves the right to change the contents without notice. www.grinnell.com

Figure 460 End Caps Tech Data Sheet: G570 Part Number 460H000344 E to E 25 33.7 58.0 0.5 460H000424 460H000484 460H000604 460H000764 460H000894 460H001144 460H001394 460H001684 460H002194 460H002734 460H003244 32 42.4 58.0 0.5 40 48.3 58.0 0.5 50 60.3 58.0 0.9 65 76.1 60.0 1.4 80 88.9 60.0 2.0 100 114.3 60.0 3.9 125 139.7 60.0 6.1 150 * 168.3 66.0 8.4 200 * 219.1 81.0 16.6 250 * 273.0 81.0 27.2 300 * 323.9 81.0 30.4 K L M K * Dished Cap Schedule 40 fittings available upon request, contact a GRINNELL Sales Representative. See page 141 for stainless steel fitting specifications. For instructions on part numbers, ordering information, and availability, refer to page 15 or contact a GRINNELL Sales Representative. Refer to back cover for country-specific contact information 153

Figure 421 Reducing Tees Tech Data Sheet: G570 N O P Q Part Number 421H020104 421H020124 421H020154 421H026154 421H026204 421H030204 C to E C to B 50 x 50 x 25 60.3 x 60.3 x 33.7 68.0 68.0 1.0 50 x 50 x 32 60.3 x 60.3 x 42.4 68.0 68.0 1.1 50 x 50 x 40 60.3 x 60.3 x 48.3 68.0 68.0 1.1 50 x 50 x 40 76.1 x 76.1 x 48.3 76.0 76.0 1.2 50 x 50 x 50 76.1 x 76.1 x 60.3 76.0 76.0 2.0 80 x 80 x 50 88.9 x 88.9 x 60.3 83.0 86.0 2.5 N O P R 421H030264 421H042204 80 x 80 x 65 88.9 x 88.9 x 76.1 83.0 86.0 2.6 100 x 100 x 50 114.3 x 114.3 x 60.3 95.0 105.0 4.6 421H042264 100 x 100 x 65 114.3 x 114.3 x 76.1 95.0 105.0 5.1 421H042304 100 x 100 x 80 114.3 x 114.3 x 88.9 95.0 105.0 5.2 421H052304 125 x 125 x 80 139.7 x 139.7 x 88.9 108.0 124.0 6.7 421H052424 125 x 125 x 100 139.7 x 139.7 x 114.3 108.0 124.0 6.7 421H063204 150 x 150 x 50 168.3 x 168.3 x 88.9 122.0 143.0 11.8 421H063264 150 x 150 x 65 168.3 x 168.3 x 76.1 122.0 143.0 12.0 421H063304 150 x 150 x 80 168.3 x 168.3 x 60.3 122.0 143.0 12.1 421H063424 150 x 150 x 100 168.3 x 168.3 x 114.3 122.0 143.0 12.2 421H063524 150 x 150 x 125 168.3 x 168.3 x 139.7 122.0 143.0 12.2 421H080424 200 x 200 x 100 219.1 x 219.1 x 114.1 148.0 178.0 24.2 421H080524 200 x 200 x 125 219.1 x 219.1 x 139.7 148.0 178.0 24.2 421H080634 200 x 200 x 150 219.1 x 219.1 x 168.3 148.0 178.0 24.2 421H011634 250 x 250 x 150 273.0 x 273.0 x 168.3 194.0 216.0 30.1 421H011804 250 x 250 x 200 273.0 x 273.0 x 219.1 204.0 216.0 30.1 421H013804 300 x 300 x 200 323.9 x 323.9 x 219.1 229.0 254.0 35.6 421H013114 300 x 300 x 250 323.9 x 323.9 x 273.0 242.0 254.0 35.6 Schedule 40 fittings available upon request, contact a GRINNELL Sales Representative. See page 141 for stainless steel fitting specifications. For instructions on part numbers, ordering information, and availability, refer to page 15 or contact a GRINNELL Sales Representative. 154 GRINNELL reserves the right to change the contents without notice. www.grinnell.com

Figure 450 Concentric Reducers Tech Data Sheet: G570 A : B A Part Number 450H012104 450H015104 450H015124 450H020154 450H026154 450H026204 E to E 32 x 25 42.4 x 33.7 120.0 0.5 40 x 25 48.3 x 33.7 134.0 0.5 40 x 32 48.3 x 42.4 99.0 0.5 50 x 40 60.3 x 48.3 111.0 1.0 65 x 40 76.1 x 48.3 125.0 1.0 65 x 50 76.1 x 60.3 125.0 1.1 Part Number 450H063424 450H063524 450H080424 450H080524 450H080634 450H011634 E to E 150 x 100 168.3 x 114.3 175.0 1.6 150 x 125 168.3 x 139.7 210.0 1.7 200 x 100 219.1 x 114.3 227.0 1.7 200 x 125 219.1 x 139.7 227.0 2.5 200 x 150 219.1 x 168.3 227.0 2.5 250 x 150 273.0 x 168.3 278.0 2.5 450H030154 450H030204 80 x 40 88.9 x 48.3 125.0 1.1 80 x 50 88.9 x 60.3 125.0 1.1 450H011804 450H013804 250 x 200 273.0 x 219.1 278.0 3.4 300 x 200 323.9 x 219.1 300.0 4.7 450H030264 80 x 65 88.9 x 76.1 125.0 1.1 450H013114 300 x 250 323.9 x 273.0 300.0 5.2 450H042204 450H042264 450H042304 450H052304 450H052424 100 x 50 114.3 x 60.3 135.0 1.1 100 x 65 114.3 x 76.1 135.0 1.3 100 x 80 114.3 x 88.9 135.0 1.3 125 x 80 139.7 x 88.9 162.0 1.3 125 x 100 139.7 x 114.3 162.0 1.6 For information on alternative sizes, contact a GRINNELL Sales Representative. Schedule 40 fittings available upon request, contact a GRINNELL Sales Representative. See page 141 for stainless steel fitting specifications. For instructions on part numbers, ordering information, and availability, refer to page 15 or contact a GRINNELL Sales Representative. Refer to back cover for country-specific contact information 155

Shurjoint Figure SJ-400 Butterfly Valve (Page 1 of 2) Shurjoint Tech Data Sheet: K-16 The Shurjoint Model SJ-400 Butterfly Valve is a grooved end stainless steel butterfly valve, supplied with a 10 position lever handle (SJ-400-L) or worm gear operator (SJ-400-W). The body is available in CF8M (type 316) to ASTM A 743 with integral neck and ISO 5211 mounting pad. It features a dual seal disc encapsulated with Gr. E EPDM for cold and hot water services. The end-to-end dimensions conform to MSS SP-67. The SJ-400 is UL classified in accordance with ANSI/NSF 61 and Annex G for potable water use to temperature 23 C (73.4 F). Pressure-Temperature Rating SJ-400-L 50-300 (2" - 12") Nom. Rating Class 150 Working Pressure (S40S, Roll-grooved) 20 Bar @38 C Max. Service Temperature EPDM: 110 C! Nitrile: 82 C " # $ % &! pipe. Apply 110% for cut-grooved Sch. 40S pipe. Apply 80% for roll-grooved Sch. 10S pipe and 50% for roll-grooved Sch. 5S pipe. SJ-400-W 350-600 (14" - 24") MATERIAL SPECIFICATIONS Valve Body: 743, A 351, or A 744 which is UL classified in accordance with ANSI/NSF 61 and Annex G for potable water use to temperature 23 C (73.4 F). Stems: Disc: EPDM. Disc Encapsulation: : EPDM Rubber is classified in accordance with ANSI/NSF 61 and Annex G for potable water use to temperature 23 C (73.4 F) O-Rings: Gear Box: A 351. Equivalent Length on Sch. 40 Pipe* Meter Feet 50 60.3 2.48 65 73 2.48 65 76.1 2.48 80 88.9 2.56 100 114.3 2.53 125 139.7 2.99 125 141.3 2.99 150 165.1 2.26 150 168.3 2.26 200 219.1 3.35 250 273.0 3.20 300 323.9 3.66 350 355.6 7.62 400 406.4 7.92 450 457.2 9.75 500 508.0 11.37 600 609.6 13.32 * At 15 feet/sec. (4.6m/s) velocity of water. Cv Values 120 210 210 380 720 1150 1150 2250 2250 3800 5500 8250 9500 13000 16000 20000 29000 156 GRINNELL reserves the right to change the contents without notice. www.grinnell.com

' @ ) A U A ' ( @ Shurjoint Figure SJ-400 Butterfly Valve (Page 2 of 2) Shurjoint Tech Data Sheet: K-16 S T @ T S T @ T ) SJ-400-L 50-300 (2" - 12") SJ-400-W 350-600 (14" - 24") Dimensions - E F E A B C D (Gear (Lever) Operator) 50 60.3 81 64 63 106 153 192 154 2.3 65 73 97 79 68 110 153 192 154 3.2 65 76.1 97 79 68 110 153 192 154 3.2 80 88.9 97 92 76 126 153 192 154 3.5 100 114.3 116 118 89 135 153 260 154 5.0 125 139.7 148 145 102 168 153 260 154 7.1 125 141.3 148 145 102 168 153 260 154 7.1 150 165.1 148 145 102 184 153 260 154 9.2 150 168.3 148 145 102 184 153 260 154 9.2 200 219.1 133 222 140 208 200 260 203 12.2 250 273.0 159 276 170 235 200 356 203 28.3 300 323.9 165 327 205 260 200 356 203 40.0 350 355.6 178 365 224 276 242 305 59.0 400 406.4 178 416 248 302 242 305 67.0 450 457.2 203 470 283 350 242 305 86.0 500 508.0 216 527 314 383 290 412 133.0 600 609.6 254 629 368 453 290 412 160.0 Refer to the Shurjoint technical data sheet for complete technical information and installation instructions. More information about Shurjoint Piping Products can be found on page 14 in the General Data section of this book or on www.shurjoint.com. Refer to back cover for country-specific contact information 157

W Y V X Shurjoint Figure SJ-600L Ball Valve (Lever) (Page 1 of 2) Shurjoint Tech Data Sheet: K-12 The Shurjoint Model SJ-600L is a stainless steel, groovedend, two-piece, full port ball valve designed and tested in conformance with MSS SP-110 and SP-72. The lever handle is equipped with tamper resistant locking holes. The SJ-600L is comprised of a stainless steel body and end cap, virgin TFE seats and stainless steel trim. The valve is supplied standard in CF8M (316). MATERIAL SPECIFICATIONS Body, End Cap, Stem, and Ball: 40-80 (1 1 2" - 3") Seats: Seals: Lever Handle: Flow Data (Cv Values in Dimensions table): Values for flow of water at 16 C (60 F). Where: Cv = Flow coefficient Q = Flow (GPM) P = Pressure drop (psi) 100 (4") Pressure-Temperature Rating Nom. Rating CWP Working Pressure Shell Test (S40S, Roll-grooved) (Hydrostatic) 42 Bar @38 C 63 Bar Max. Service Temperature EPDM: 110 C! Nitrile: 82 C " # $ % &! *Working pressure is for connection with cut- or roll-grooved schedule Sch. 40S pipe. *Seat test: 110% the working pressure. Dimensions - L H W d Cv Value 40 48.3 140 94 193 38 3.0 270 50 60.3 156 105 193 50 4.0 500 65 73.0 180 110 250 65 7.0 800 65 76.1 180 110 250 65 7.0 800 80 88.9 214 152 250 78 9.4 1200 100 114.3 240 167 290 100 25.0 2150 * The weight includes the lever handle. Refer to the Shurjoint technical data sheet for complete technical information and installation instructions. More information about Shurjoint Piping Products can be found on page 14 in the General Data section of this book or on www.shurjoint.com. 158 GRINNELL reserves the right to change the contents without notice. www.grinnell.com

Z V X The Shurjoint Model SJ-600W is supplied with a worm gear operator. The standard gear operator is supplied with a bracket and extension sleeve. The ISO 5211 mounting pad allows for mounting of other power actuators. Sizes available are 50 to 100 (2" to 4"). Shurjoint Figure SJ-600W Ball Valve (Gear) (Page 2 of 2) Shurjoint Tech Data Sheet: K-12 Dimensions - K H W Cv Value 50 60.3 152 137 203 8.10 500 65 73.0 152 145 203 11.10 800 65 76.1 152 145 203 11.10 800 80 88.9 152 182 203 13.50 1200 100 114.3 152 203 203 29.0 2150 * The weight includes the worm gear operator. Refer to the Shurjoint technical data sheet for complete technical information and installation instructions. More information about Shurjoint Piping Products can be found on page 14 in the General Data section of this book or on www.shurjoint.com. General Notes: Maximum Working Pressure (CWP) listed is the maximum cold water pressure for general piping services tested to ASTM F1476 and or AWWA C606 methods. Figures listed are based on roll- or cut-grooved standard wall stainless steel pipe. For other pipe schedules or pipe materials, contact Shurjoint for additional information. Field Joint Test: For one time only the system may be tested hydrostatically at 1½ times the maximum working pressure listed (AWWA C606 5.2.3). Warning: Piping systems must always be depressurized and drained before attempting disassembly and or removal of any components. Shurjoint reserves the right to change specifications, designs and or standard without notice and without incurring any obligations. Refer to back cover for country-specific contact information 159

W ) V X ' Shurjoint Figure SJ-630 Three Port Ball Valve Shurjoint Tech Data Sheet: K-25 The Shurjoint Model SJ-630 is a grooved-end three-port ball valve designed to divert media from bottom inlet to either of the two outlets ports. The valve port is a regular port size and the stem is a blowout proof design to MSS SP-72 and API Standard 608. The valve is supplied with a carbon steel lever handle equipped with a tamper resistant locking device. The valve body and three-port ball are made of austenitic stainless steel conforming to ASTM A351 CF8M(316) and blowout proof stem is stainless steel to ASTM A479 Type 316. The Valve body and trim materials are in compliance with NACE MR-01-75 requirement. MATERIAL SPECIFICATIONS Body, End Cap & Ball: S T @ T Y Stem: Seats: Body Seal: Stem Hardware: Lever Handle: Pressure-Temperature Rating Nom. Rating CWP Working Pressure (S40S, Roll-grooved) 41 Bar @38 C Max. Service Temperature EPDM: 110 C! Nitrile: 82 C " # $ % &! * Working pressure is based on connection with roll- or cutgrooved Sch. 40S stainless steel pipe. * Seat test: 110% the working pressure. * Shell test: 1.5 times the working pressure. Dimensions - L H W d A B Cv / Kv Value 50 60.3 167 110 228 38 83 79 3.58 36 / 31 Refer to the Shurjoint technical data sheet for complete technical information and installation instructions. More information about Shurjoint Piping Products can be found on page 14 in the General Data section of this book or on www.shurjoint.com. 160 GRINNELL reserves the right to change the contents without notice. www.grinnell.com

( ' ) The Shurjoint Model SS-726 Groovedend Y-Strainers are designed to strain debris and foreign matter from piping systems and thus provide inexpensive protection for costly pumps, meters and other components. Cleaning and maintenance of the screen can be accomplished easily by removing the coupling. The Model SS-726 Y-Strainer is suitable for vertical or horizontal installations. Shurjoint Figure SJ-726 Y Strainer Shurjoint Tech Data Sheet: K-11 MATERIAL SPECIFICATIONS Body, End-Cap, Drain Plug and Coupling Segments: A 743 Gr. CF8 Bolts & Nuts: B-8 with heavy duty nuts to ASTM A 194 B8, Molybdenum disulfide (MoS2) coated. B-8M with heavy duty nuts to ASTM B8M, Molybdenum disulfide (MoS2) coated. Screen: Factory s standard screen perforation is 3.2 ( 1 8"). Other perforations are available upon request. Flow Data (Cv Values in Dimensions table): Values for flow of water at 16 C (60 F). Where: Cv = Flow coefficient Q = Flow (GPM) P = Pressure drop (psi) Pressure-Temperature Rating Nom. Rating Class 150 Working Pressure (S40S, Roll-grooved) 20 Bar @ 38 C Max. Service Temperature EPDM: 110 C! Nitrile: 82 C " # $ % &! pipe. Apply 110% for cut-grooved Sch. 40S pipe. Apply 80% for roll-grooved Sch. 10S pipe and 50% for roll-grooved Sch. 5S pipe. water. Max. Working Pressure Bar Dimensions - A B C Drain Plug Size Cv Valve 65 73.0 20 273 199 122 15 7.6 92 80 88.9 20 299 221 129 15 8.6 162 100 114.3 20 362 269 168 25 9.6 284 150 168.3 20 470 357 219 25 39.0 770 Refer to the Shurjoint technical data sheet for complete technical information and installation instructions. More information about Shurjoint Piping Products can be found on page 14 in the General Data section of this book or on www.shurjoint.com. Refer to back cover for country-specific contact information 161

) ' ( @ Shurjoint Figure SS-723 Mechanical Tee Shurjoint Tech Data Sheet: K-10 For detailed Listing / Approval information contact GRINNELL Mechanical Products ^ _ ` a b c d The Shurjoint Model SS-723 stainless steel mechanical tee is the ideal fitting for branch or direct outlet connections to sprinkler heads, drop nipples and or gauges on stainless steel pipe. No need for welding, simply cut or drill a hole at the desired location, position the housing so that the locating collar fits within the hole and secure with the bolts and nuts. The SS-723 is comprised of stainless steel investment cast housings, EPDM gasket and stainless steel track bolts and nuts. The SS-723 is available in grades CF8 (304) and CF8M (316). Additional sizes and or grades are available on request, please contact for Shurjoint for details. MATERIAL SPECIFICATIONS Housing: Bolts & Nuts: nuts to ASTM A 194 B8, Molybdenum disulfide (MoS2) coated. duty nuts to ASTM B8M, Molybdenum disulfide (MoS2) coated. Pressure-Temperature Rating Nom. Rating Class 150 Working Pressure (S40S, Roll-grooved) 20 Bar @ 38 C Max. Service Temperature EPDM: 110 C! Nitrile: 82 C " # $ % &! Hole Diameter Dimensions - Sealing Surface - A B C D T* Bolt Size. in [ \ 32 x 15 30 41 26 87 49 27 0.3 5 16 x 1 1 2 [ ] 32 x 20 30 44 26 87 49 29 0.3 5 16 x 1 1 2 32 x 25 30 51 26 87 49 34 5 0.4 [ 16 x 1 1 2 \ \ 40 x 15 30 44 29 90 49 30 0.3 5 16 x 1 1 2 \ ] 40 x 20 30 46 29 90 49 31 0.3 5 16 x 1 1 2 \ 40 x 25 30 53 29 90 49 36 0.4 5 16 x 1 1 2 \ 50 x 15 30 51 36 109 51 37 0.5 5 16 x 1 1 2 50 x 20 30 53 36 109 51 28 5 0.5 16 x 1 1 2 ] T*: Take-out (Centre of run to end of pipe to be engaged) Refer to the Shurjoint technical data sheet for complete technical information and installation instructions. More information about Shurjoint Piping Products can be found on page 14 in the General Data section of this book or on www.shurjoint.com. 162 GRINNELL reserves the right to change the contents without notice. www.grinnell.com