33-400, 33-401, 33-402, 33-403 14 RADIAL SAWS 33-410, 33-411, 33-412, 33-413 16 RADIAL SAWS 33-420, 33-421, 33-422, 33-423 18 RADIAL SAWS RAS-5E PART NO. 424-03-651-0018 Date: 04/08/02 Page1/ RAS-5E /DEB
REPLACEMENT PARTS 1 424-03-074-0002 HOLE PLUG 2 424-03-074-0001 LOCATING PIN 3 901-01-060-0605 5/16-18 X 1/2" HEX HD SCREW 4 904-10-031-3810 WASHER 5 424-03-030-0009 INDEX COLUMN, INCL.:, NOTE C 424-03-030-0007 INDEX COLUMN, NOTE D 6 951-02-011-3974 MITER SCALE 7 901-06-450-2250 #04 X 3/16" ROUND HD SCREW 8 424-03-089-0016 ARM, NOTE C 424-03-089-0014 ARM, NOTE D 9 438-01-011-0051 BUSHING INSULATOR 10 438-01-004-0082 CABLE CLAMP 11 901-03-040-8015 1/4-20 X 1/2" BUTTON HD SCREW 12 905-02-010-7105 1/4" X 1 1/4" GROOVE PIN 13 901-03-030-8013 1/4-20 X 3/4" FLAT HD SCREW 14 424-04-004-0005 COLUMN KEY 15 904-02-020-1705 1/2" LOCK WASHER 16 901-01-060-3117 1/2-13 X 2" HEX HD SCREW 17 424-03-030-0008 COLUMN 18 929-76-010-6318 ELEVATING NUT 19 904-02-010-1703 5/16" LOCK WASHER 20 901-01-060-0649 5/16-18 X 1" HEX HD SCREW 21 931-01-011-4091 BALL HANDLE 22 1085978 HANDLE ASSY 23 1085979 LOCK SCREW 24 901-04-150-0206 5/16-18 X 5/16" HEX SOC SET SCREW 25 904-01-033-1306 FLAT WASHER 26 424-03-017-0003 SPACER 27 901-03-010-3345 1/4-20 X 1" HEX SOC HD SCREW 28 424-04-061-0003 CABLE SUPPORT 29 904-01-010-1610 FLAT WASHER 30 951-01-010-7802 POINTER 31 0908459 SCREW 32 901-04-170-1104 1/4-20 X 1/4" HEX SOC SET SCREW 33 424-03-388-0006 PLUNGER ASSY, INCL: 34 928-01-041-5310 SPRING 35 901-06-450-8210 #00 X 1/8" ROUND HD SCREW 36 902-01-010-1300 5/16-18 HEX NUT 37 931-01-021-4099 KNOB 38 905-01-010-6731 5/64 X 1/2" SPRING PIN 39 1087358 CLAMP ASSY, INCL: 40 406-03-138-0005 KNOB 41 424-03-016-0002 BUMPER 42 424-03-132-0007 RIP SCALE 43 901-02-010-0558 #08-32 X 1/4" ROUND HD SCREW 44 424-03-355-0012 TRACK ARM ASSY, INCL:, NOTE C 424-03-355-0011 TRACK ARM ASSY, INCL:, NOTE D 45 901-03-010-0775 3/8-16 X 1" HEX SOC HD SCREW 46 424-03-031-0011 TRACK END COVER 47 905-02-010-7105 1/4" X 1 1/4" GROOVE PIN 48 904-02-020-1705 1/2" LOCK WASHER 49 901-03-010-3308 1/2-13 X 1 3/4" HEX SOC HD SCREW 52 424-00-752-0002 WARNING LABEL, NOTE C 424-00-752-0001 WARNING LABEL, NOTE D 53 424-03-108-0007 ROD 54 902-03-020-2982 #10-32 PUSH NUT 55 901-02-010-0541 #10-24 X 3/4" ROUND HD SCREW 60 0906348 LOCK NUT 61 1085980 YOKE PIN 62 424-04-111-0006 ECCENTRIC STUD 63 424-04-111-0005 STATIONARY STUD 64 920-10-151-4919 BALL BEARING 65 901-02-010-0558 #08-32 X 1/4" ROUND HD SCREW 66 951-01-021-3951 POINTER 67 424-04-327-0002 RIP LOCK ASSY, INCL: 68 406-03-138-0005 KNOB 69 424-03-072-0004 HOLD DOWN STRIP 70 424-03-388-0007 LOCATING HOUSING, INCL:, NOTE C 424-03-388-0001 LOCATING HOUSING, INCL:, NOTE D 71 931-01-021-4099 KNOB 72 928-01-041-5310 SPRING 73 901-03-010-0784 3/8-16 X 1 1/4" HEX SOC HD SCREW 74 904-02-020-1704 3/8" LOCK WASHER 76 424-03-057-0001 ROLLER HEAD 77 901-04-150-0202 1/4-20 X 1/2" HEX SOC SET SCREW 78 424-03-016-0002 BUMPER 79 904-02-020-1705 1/2" LOCK WASHER 80 902-01-020-1227 1/2-20 JAM NUT 81 424-03-016-0003 BUMPER 82 901-02-010-0558 #08-32 X 1/4" ROUND HD SCREW 83 424-04-031-0018 COVER, NOTE C 424-04-031-0009 COVER, NOTE D 84 931-01-011-4091 BALL HANDLE 85 1085982 HANDLE ASSY 86 901-04-160-1103 5/16-18 X 5/8" HEX SOC SET SCREW 87 424-03-102-0008 YOKE, INCL:, NOTE C 424-03-102-0005 YOKE, INCL:, NOTE D 88 424-12-752-0049 WARNING LABEL, NOTE C 424-12-072-0021 WARNING LABEL, NOTE D 89 902-01-040-1026 3/8-16 HEX NUT 90 904-01-031-2925 FLAT WASHER 91 424-04-027-0004 LOCK NUT 92 931-01-021-4099 KNOB 93 901-07-261-3234 LOCK ROD 94 901-01-060-3121 3/8-16 X 3 1/2" HEX HD SCREW 95 901-02-010-0558 #08-32 X 1/4" ROUND HD SCREW 96 951-01-010-7802 POINTER 97 904-01-010-1610 FLAT WASHER 98 424-03-388-0007 HOUSING ASSY, INCL:, NOTE C 424-03-388-0001 HOUSING ASSY, INCL:, NOTE D 99 928-01-041-5310 SPRING 100 931-01-021-4099 KNOB 101 904-02-020-1704 3/8" LOCK WASHER 102 901-03-010-0784 3/8-16 X 1 1/4" HEX SOC HD SCREW 105 33-723 RETURN SPRING, INCL: 106 901-03-043-1676 3/8-16 X 1 1/4" BUTTON HD SCREW SERVICE NOTES C: S/N'S BEGINNING WITH 01J AND ABOVE D: S/N'S BEGINNING WITH 01I AND BELOW Page 2/ RAS-5E /DEB
FOR 14 RADIAL SAWS ONLY Page3/ RAS-5E /DEB
REPLACEMENT PARTS 107 424-03-014-0015 S-HOOK 110 902-01-010-1282 1/2-13 HEX NUT 111 904-01-010-1618 9/16" FLAT WASHER 112 424-04-054-0021 CLAMP 113 424-04-111-0010 STUD 114 904-07-010-5568 FIBER WASHER 115 901-03-010-0793 1/2-13 X 1" HEX SOC HD SCREW 116 904-02-020-1705 1/2" LOCK WASHER 117 901-03-010-0750 5/16-18 X 1" HEX SOC HD SCREW 118 904-02-010-1703 5/16" LOCK WASHER 119 424-04-095-0002 TRUNNION BOSS 120 424-04-360-0001 ARBOR NUT ASSY, INCL: 121 901-03-010-8072 #06-32 X 3/4" HEX SOC HD SCREW 122 955-03-010-0047 5/64" HEX WRENCH 123 424-04-103-0005 ARBOR COLLAR, NOTE C 33-814 ARBOR COLLAR, NOTE D 124 OPTIONAL BLADE 125 400-06-131-0024 MOTOR ASSY - 3HP, 1PH, 230V, INCL: 400-06-131-0026 MOTOR ASSY - 5HP, 3PH, 230/460V, INCL.: 400-06-131-0028 MOTOR ASSY - 5HP. 3PH, 575V, INCL: 400-06-131-0029 MOTOR ASSY - 5HP, 3PH, 200V, INCL: * 901-03-010-0783 #10-32 X 3/4" HEX SOC HD SCREW * 438-01-026-0008 RECTIFIER 126 927-03-010-2666 KEY 127 928-01-023-1666 SPRING 128 904-01-031-2903 FLAT WASHER 129 424-04-015-0004 BRAKE COIL (NOTES A & B) 130 424-04-015-0003 BRAKE DISC (NOTES A & B) 131 901-06-423-1170 #10-32 X 5/8" HEX HD SCREW 132 424-04-031-0016 COVER 133 902-01-213-1680 LOCK NUT (B) 135 438-01-033-0003 FAN (B) 136 901-03-033-1678 #08-32 X 3/4" FLAT HD SCREW (A) 137 928-01-023-1670 SPRING (NOTE A) 138 904-02-020-1702 1/4" LOCK WASHER 139 901-03-010-0229 1/4-20 X 1/2" HEX SOC HD SCREW (A) 140 424-03-095-0006 FRONT TRUNNION, NOTE C 424-03-095-0005 FRONT TRUNNION, NOTE D 141 904-02-020-1705 1/2" LOCK WASHER 142 901-03-010-0765 1/2-13 X 1 1/2" SOC HD SCREW, NOTE C 901-03-010-3308 1/2-13 X 1 3/4" SOC HD SCREW, NOTE D 144 424-03-132-0010 BEVEL SCALE, NOTE C 424-03-132-0008 BEVEL SCALE, NOTE D 145 901-02-010-0567 #06-32 X 1/4" ROUND HD SCREW * 33-449 RETRACTABLE LEAF GUARDS, CONST OF: 174 424-03-354-0014 14" BLADE GUARD ASSY, INCL:, NOTE C 424-03-354-0011 14" BLADE GUARD ASSY, INCL:, NOTE D 175 901-09-011-2455 STUD 176 424-03-054-0001 REAR LEAF 177 424-01-111-0003 STUD (CMO) 178 904-15-210-7403 CLIP (CMO) 179 424-03-054-0023 FRONT LEAF 180 901-09-011-2456 STUD 181 928-02-231-3394 SPRING 183 424-02-752-0083 NAMEPLATE, NOTE C 426-13-754-0001 NAMEPLATE, NOTE D 184 901-06-450-2250 #04 X 3/16" ROUND HD SCREW (EMO) 185 901-04-260-1505 1/4-20 X 1/2" THUMB SCREW 186 901-04-260-1527 5/16-18 X 3/4" THUMB SCREW 187 424-03-036-0001 DUST SPOUT 188 424-02-752-0084 CAUTION PLATE 188A 424-12-754-0012 DIRECTIONAL ARROW, NOTE C 189 904-15-062-0269 EXT RET RING (EMO) 190 904-01-010-1614 FLAT WASHER (EMO) 191 424-08-071-0001 PIN (EMO) 192 424-04-408-0002 ANTI-KICK ASSY, INCL: 193 424-04-071-0013 PIN 194 904-15-062-0269 EXT RET RING 195 905-02-010-2489 1/8" X 7/8" GROOVE PIN 196 424-04-047-0002 ANTI-KICK FINGER * NOT SHOWN ASSEMBLED SERVICE NOTES: A-When servicing brake disc ( No 130) and /or brake coil disc ( No 129), the air gap between the two parts must be readjusted as follows: Install the coil assembly to the motor housing and securely tighten the four (4) coil retaining screw ( No 139), Replace three (3) springs ( No 137) and positions the brake disc assembly ( No 130) carefully over the indexing roll pins protruding from the coil assembly. Apply a small amount of thread locking compound to the two (2) brake Disc retaining screws ( No 136) and install screws to temporarily retain brake disc. Adjust the air gap between the coil and disc assemblies to.025 by tightening the two (2) disc retaining screws while using a feeler gage to control the air gap. See sketch below. Brake Disc Assembly Brake Disc Retaining Screws.025 Feeler Gage 3/32" Allen Wrench B- After extensive use, the brake pad material bonded to brake disc assemble ( No 130) may wear to the point where it no longer contacts the mating surface on fan ( No 135). To restore proper pad/fan operating clearance, proceed as follows: Securely tighten Lock Nut ( No 133) to fully compress the brake disc and fan against the brake coil assembly ( No 129). At this point, all air gaps should be fully compressed. Carefully back off the lock nut ( No 133) ½ turn, (.010 gap between brake disc ( No 130) and fan ( No 135). Note: This procedure must be repeated whenever the fan ( No 135) is removed and replaced. C: S/N'S BEGINNING WITH 01J AND ABOVE D: S/N'S BEGINNING WITH 01I AND BELOW Page4/ RAS-5E /DEB
FOR 16 RADIAL SAWS ONLY Page 5/ RAS-5E /DEB
REPLACEMENT PARTS 210 902-01-010-1282 1/2-13 HEX NUT 211 904-01-010-1618 9/16" FLAT WASHER 212 424-04-054-0021 CLAMP 213 424-04-111-0010 STUD 214 904-07-010-5568 FIBER WASHER 215 901-03-010-0793 1/2-13 X 1" HEX SOC HD SCREW 216 904-02-020-1705 1/2" LOCK WASHER 217 901-03-010-0750 5/16-18 X 1" HEX SOC HD SCREW 218 904-02-010-1703 5/16" LOCK WASHER 219 424-04-095-0002 TRUNNION BOSS 220 424-04-360-0001 ARBOR NUT ASSY, INCL: 221 901-03-010-8072 #06-32 X 3/4" HEX SOC HD SCREW 222 955-03-010-0047 HEX WRENCH 223 424-04-103-0005 ARBOR COLLAR, NOTE C 33-814 ARBOR COLLAR, NOTE D 224 OPTIONAL BLADE 225 400-06-131-0024 MOTOR ASSY - 3HP, 1PH, 230V, INCL: 400-06-131-0026 MOTOR ASSY - 5HP, 3PH, 230/460V, INCL.: 400-06-131-0028 MOTOR ASSY - 5HP, 3PH, 575V, INCL: 400-06-131-0029 MOTOR ASSY - 5HP, 3PH, 200V, INCL: * 438-01-026-0008 RECTIFIER * 901-03-010-0783 #10-32 X 3/4" HEX SOC HD SCREW 226 927-03-010-2666 KEY 227 928-01-023-1666 SPRING 228 904-01-031-2903 FLAT WASHER 229 424-04-015-0004 BRAKE COIL (NOTES A & B) 230 424-04-015-0003 BRAKE DISC (NOTES A & B) 231 901-06-423-1170 #10-32 X 5/8" HEX HD SCREW 232 424-04-031-0016 COVER 233 902-01-213-1680 LOCK NUT (NOTE A & B) 235 438-01-033-0003 FAN (NOTE B) 236 901-03-033-1678 #08-32 X 3/4" FLAT HD SCREW (A) 237 928-01-023-1670 SPRING (NOTE B) 238 904-02-020-1702 1/4" LOCK WASHER 239 901-03-010-0229 1/4-20 X 1/2" HEX SOC HD SCREW (A) 240 424-03-095-0006 FRONT TRUNNION, NOTE C 424-03-095-0005 FRONT TRUNNION, NOTE D 241 904-02-020-1705 1/2" LOCK WASHER 242 901-03-010-0765 1/2-13 X 1 1/2" SOC HD SCREW, NOTE C 901-03-010-3308 1/2-13 X 1 3/4" SOC HD SCREW, NOTE D 244 424-03-132-0010 BEVEL SCALE, NOTE C 424-03-132-0008 BEVEL SCALE, NOTE D 245 901-02-010-0567 #06-32 X 1/4" ROUND HD SCREW 265 424-03-354-0015 16" BLADE GUARD ASSY, INCL:, NOTE C 424-03-354-0012 16" BLADE GUARD ASSY, INCL:, NOTE D 266 901-04-260-1528 5/16-18 X 1" THUMB SCREW 267 424-04-036-0001 DUST SPOUT 268 424-02-752-0083 NAMEPLATE 269 901-06-450-2250 #04 X 3/16" ROUND HD SCREW 270 424-02-752-0084 CAUTION PLATE, NOTE C 960-04-010-1887 CAUTION PLATE, NOTE D 270A 424-12-754-0012 DIRECTIONAL ARROW, NOTE C * 33-450 RETRACTABLE LEAF GUARDS, CONST OF: 271 901-06-450-2250 #04 X 3/16" ROUND HD SCREW 272 928-02-231-3394 SPRING 273 901-09-011-2456 STUD 274 901-09-011-2455 STUD 275 424-04-054-0011 REAR LEAF 276 904-15-210-7403 CLIP 277 424-01-111-0003 STUD 278 424-04-054-0010 FRONT LEAF 280 424-04-408-0002 ROD ASSY, INCL: 281 904-15-062-0269 EXT RET RING 282 424-04-047-0002 ANTI-KICK FINGER 283 905-02-010-2489 1/8" X 7/8" GROOVE PIN 284 424-04-071-0013 PIN * NOT SHOWN ASSEMBLED SERVICE NOTES: A-When servicing brake disc ( No 230) and /or brake coil disc ( No 229), the air gap between the two parts must be readjusted as follows: Install the coil assembly to the motor housing and securely tighten the four (4) coil retaining screws ( No 239), Replace three (3) springs ( No 237) and positions the brake disc assembly ( No 230) carefully over the indexing roll pins protruding from the coil assembly. Apply a small amount of thread locking compound to the two (2) brake Disc retaining screws ( No 236) and install screws to temporarily retain brake disc. Adjust the air gap between the coil and disc assemblies to.025 by tightening the two (2) disc retaining screws while using a feeler gage to control the air gap. See sketch below. Brake Disc Assembly Brake Disc Retaining Screws.025 Feeler Gage 3/32" Allen Wrench B- After extensive use, the brake pad material bonded to brake disc assembles ( No 230) may wear to the point where it no longer contacts the mating surface on fan ( No 235). To restore proper pad/fan operating clearance, proceed as follows: Securely tighten Lock Nut ( No 233) to fully compress the brake disc and fan against the brake coil assembly ( No 229). At this point, all air gaps should be fully compressed. Carefully back off the lock nut ( No 233) ½ turn, (.010 gap between brake disc ( No 230) and fan ( No 235). Note: This procedure must be repeated whenever the fan ( No 235) is removed and replaced. C: S/N'S BEGINNING WITH 01J AND ABOVE D: S/N'S BEGINNING WITH 01I AND BELOW Page 6/ RAS-5E /DEB
FOR 18 RADIAL SAWS ONLY Page 7/ RAS-5E /DEB
REPLACEMENT PARTS 310 902-01-010-1282 1/2-13 HEX NUT 311 904-01-010-1618 9/16" FLAT WASHER 312 424-04-054-0021 CLAMP 313 424-04-111-0010 STUD 314 904-07-010-5568 FIBER WASHER 315 901-03-010-0793 1/2-13 X 1" HEX SOC HD SCREW 316 904-02-020-1705 1/2" LOCK WASHER 317 901-03-010-0750 5/16-18 X 1" HEX SOC HD SCREW 318 904-02-010-1703 5/16" LOCK WASHER 319 424-04-095-0002 TRUNNION BOSS 320 424-04-360-0001 ARBOR NUT ASSY, INCL: 321 901-03-010-8072 #06-32 X 3/4" HEX SOC HD SCREW 322 955-03-010-0047 HEX WRENCH 323 424-04-103-0006 BLADE FLANGE, NOTE C 424-04-103-0004 BLADE FLANGE, NOTE D 324 OPTIONAL BLADE 325 400-06-131-0025 MOTOR ASSY - 5HP, 1PH, 230V, INCL: 400-06-131-0027 MOTOR ASSY - 7.5HP, 3PH, 230/460V, INCL: 400-06-131-0028 MOTOR ASSY - 5HP, 3PH, 575V, INCL: 400-06-131-0029 MOTOR ASSY - 5HP, 3PH, 200V, INCL: 400-06-131-0030 MOTOR ASSY - 7.5HP, 3PH, 575V, INC * 438-01-026-0008 RECTIFIER * 901-03-010-0783 #10-32 X 3/4" HEX SOC HD SCREW 326 927-03-010-2666 KEY 327 928-01-023-1666 SPRING 328 904-01-031-2903 FLAT WASHER 329 424-04-015-0004 BRAKE COIL (NOTES A & B) 330 424-04-015-0003 BRAKE DISC (NOTES A & B) 331 424-04-031-0016 COVER 332 901-06-423-1170 #10-32 X 5/8" HEX HD SCREW 333 902-01-213-1680 LOCK NUT (NOTE A) 335 438-01-033-0003 FAN (NOTE B) 336 901-03-033-1678 #08-32 X 3/4" FLAT HD SCREW (A) 337 928-01-023-1670 SPRING (NOTE A) 338 904-02-020-1702 1/4" LOCK WASHER 339 901-03-010-0229 1/4-20 X 1/2" HEX SOC HD SCREW (A) 340 424-03-095-0006 FRONT TRUNNION, NOTE C 424-03-095-0005 FRONT TRUNNION, NOTE D 341 904-02-020-1705 1/2" LOCK WASHER 342 901-03-010-3308 1/2-13 X 1 3/4" SOC HD SCREW 343 901-03-010-0765 1/2-13 X 1 1/2" SOC HD SCREW 344 424-03-132-0010 BEVEL SCALE, NOTE C 424-03-132-0008 BEVEL SCALE, NOTE D 345 901-02-010-0567 #06-32 X 1/4" ROUND HD SCREW 365 424-04-354-0017 18" BLADE GUARD ASSY, INCL:, NOTE C 424-04-354-0015 18" BLADE GUARD ASSY, INCL:, NOTE D 366 901-04-260-1528 5/16-18 X 1" THUMB SCREW 367 424-04-036-0001 DUST SPOUT 368 424-02-752-0083 NAMEPLATE, NOTE C 426-13-754-0001 NAMEPLATE, NOTE D 369 901-06-450-2250 #04 X 3/16" ROUND HD SCREW (EMO) 370 424-02-752-0084 CAUTION PLATE, NOTE C 960-04-010-1887 CAUTION PLATE, NOTE D 370A n 424-12-754-0012 DIRECTIONAL ARROW, NOTE C * 33-471 RETRACTABLE LEAF GUARDS, CONST OF: 371 901-06-450-2250 #04 X 3/16" ROUND HD SCREW (EMO) 372 928-02-231-3394 SPRING 373 424-04-111-0009 STUD 374 424-04-111-0007 STUD 375 424-04-054-0017 REAR LEAF 376 904-15-210-7403 CLIP 377 424-04-111-0008 BEARING STUD 378 424-04-054-0018 FRONT LEAF 380 1086605 ANTI-KICK ASSY, INCL: 381 904-15-062-0269 EXT RET RING 382 905-02-010-2489 1/8" X 7/8" GROOVE PIN 383 424-04-047-0002 ANTI-KICK FINGER 384 424-04-071-0013 PIN * NOT SHOWN ASSEMBLED SERVICE NOTES: A-When servicing brake disc ( No 330) and /or brake coil disc ( No 329), the air gap between the two parts must be readjusted as follows: Install the coil assembly to the motor housing and securely tighten the four (4) coil retaining screws ( No 339), Replace three (3) springs ( No 337) and positions the brake disc assembly ( No 330) carefully over the indexing roll pins protruding from the coil assembly. Apply a small amount of thread locking compound to the two (2) brake Disc retaining screws ( No 336) and install screws to temporarily retain brake disc. Adjust the air gap between the coil and disc assemblies to.025 by tightening the two (2) disc retaining screws while using a feeler gage to control the air gap. See sketch below. Brake Disc Assembly Brake Disc Retaining Screws.025 Feeler Gage 3/32" Allen Wrench B- After extensive use, the brake pad material bonded to brake disc assembles ( No 330) may wear to the point where it no longer contacts the mating surface on fan ( No 335). To restore proper pad/fan operating clearance, proceed as follows: Securely tighten Lock Nut ( No 333) to fully compress the brake disc and fan against the brake coil assembly ( No 329). At this point, all air gaps should be fully compressed. Carefully back off the lock nut ( No 333) ½ turn, (.010 gap between brake disc ( No 330) and fan ( No 335). Note: This procedure must be repeated whenever the fan ( No 335) is removed and replaced. C: S/N'S BEGINNING WITH 01J AND ABOVE D: S/N'S BEGINNING WITH 01I AND BELOW Page 8/ RAS-5E /DEB
Page 9/ RAS-5E /DEB
REPLACEMENT PARTS 400 901-03-040-8015 1/4-20 X 1/2" BUTTON HD SCREW 401 424-04-052-0001 GIB 402 424-04-305-0017 COLUMN BASE ASSY, INCL: 403 424-04-111-0002 STUD 404 904-02-020-1704 3/8" LOCK WASHER 405 902-01-040-1026 3/8-16 HEX NUT 406 901-01-060-3117 1/2-13 X 2" HEX HD SCREW 407 904-02-020-1705 1/2" LOCK WASHER 408 901-04-150-0297 5/16-24 X 1 3/4" HEX SOC SET SCREW 409 902-01-010-1206 5/16-24 HEX NUT 410 901-03-010-3318 #10-32 X 3/8" HEX SOC HD SCREW 411 438-01-004-0052 CORD CLAMP 412 905-02-010-7105 1/4" X 1 1/4" GROOVE PIN 413 424-03-016-0003 BUMPER 414 424-04-083-0001 SHIM WASHER (AS REQUIRED) 415 424-04-391-0006 TABLE BOARD SET 416 904-01-010-1615 FLAT WASHER 417 901-02-010-7502 3/8-16 X 1" ROUND HD SCREW 418 901-02-010-0511 1/4-20 X 7/8" ROUND HD SCREW 419 904-01-010-1614 FLAT WASHER 420 424-03-004-0014 EXTENSION BAR 421 424-04-004-0004 CLAMP STRIP 422 901-01-060-0617 3/8-16 X 1 1/2" HEX HD SCREW 423 424-04-005-0002 TABLE BASE 424 904-02-020-1704 3/8" LOCK WASHER 425 902-01-040-1026 3/8-16 HEX NUT 426 901-01-060-0644 3/8-16 X 2 1/2" HEX HD SCREW 427 438-01-011-0020 INSULATOR 428 901-01-060-0640 3/8-16 X 3/4" HEX HD SCREW 429 424-04-004-0008 REINFORCING STRIP 430 424-04-305-0018 BASE ASSY 431 438-01-004-0090 WRENCH HOLDER 432 901-05-213-1498 #10 X 1/2" HEX HD SCREW 433 904-01-033-1451 FLAT WASHER 434 424-03-014-0017 FENCE BRACKET 435 905-05-040-2105 3/32 X 3/4" COTTER PIN 436 424-04-112-0015 FENCE CLAMP SCREW 437 424-03-327-0003 FENCE CLAMP NUT 438 901-05-213-1498 #10 X 1/2" HEX HD SCREW 439 422-35-060-0001 WRENCH HOOK 440 901-01-060-0611 1/4-20 X 1/2" HEX HD SCREW 441 904-02-020-1702 1/4" LOCK WASHER 442 406-03-138-0008 KNOB SERVICE NOTES C: S/N'S BEGINNING WITH 01J AND ABOVE D: S/N'S BEGINNING WITH 01I AND BELOW 443 961-03-013-1452 GROMMET 444 1086622 ELEVATING SHAFT 445 424-04-017-0006 BEARING, NOTE C 424-04-017-0001 BEARING, NOTE D 446 901-02-030-0417 3/8-16 X 1" FLAT HD SCREW 447 905-02-010-5045 GROOVE PIN 448 424-03-333-0001 ELEVATING CRANK 449 902-01-040-1026 3/8-16 HEX NUT 450 424-02-752-0082 NAMEPLATE, NOTE C 426-13-754-0001 NAMEPLATE, NOTE D 451 424-02-014-0025 LVC BOX MOUNTING BRACKET 452 904-02-020-1702 1/4" LOCK WASHER 453 901-01-060-0611 1/4-20 X 1/2" HEX HD SCREW 454 902-01-120-1034 1/4-20 HEX NUT 455 902-01-040-1026 3/8-16 HEX NUT 456 902-01-010-5900 3/8-16 JAM NUT 457 901-04-020-0324 3/8-16 X 2" HEX SOC SET SCREW 458 901-01-060-0642 3/8-16 X 1" HEX HD SCREW 459 904-01-010-1615 FLAT WASHER 460 904-02-020-1704 3/8" LOCK WASHER 461 902-01-010-5900 3/8-16 JAM NUT 462 424-04-066-0004 LEG 463 905-01-010-2730 3/16" X 1 1/2" SPRING PIN 464 927-01-010-2607 WOODRUFF KEY 465 424-03-112-0002 ELEVATING SCREW 466 904-01-030-1649 FLAT WASHER 467 920-52-011-3924 THRUST BEARING 468 424-03-013-0003 COLUMN HOUSING 469 904-02-020-1704 3/8" LOCK WASHER 470 901-01-060-0648 3/8-16 X 1 1/4" HEX HD SCREW 471 920-24-061-3962 NEEDLE BEARING 472 920-76-021-3909 THRUST BEARING 473 905-02-010-5030 5/32 X 3/4" GROOVE PIN 474 424-02-351-0001 GEAR ASSY 475 920-76-021-3909 THRUST BEARING 476 920-24-061-3962 NEEDLE BEARING 478 424-02-351-0001 GEAR ASSY 479 902-01-150-1011 1/2-13 HEX NUT 480 905-05-040-2106 1/8" X 1 1/4" COTTER PIN 481 424-03-117-0001 ROLLER HEAD WRENCH 482 955-01-030-1488 ARBOR WRENCH 483 955-02-100-1492 ARBOR WRENCH 484 n 424-03-628-0013 STAND HARDWARE PACK STANDARD SAFETY EQUIPMENT In order to promote tool safety, Delta Machinery strictly enforces the policy of repairing or replacing any damaged or missing standard safety equipment on machines presented to Delta Authorized Service Centers for service/repairs. Any product that is presented to a Delta Authorized Service Centers for repairs which contains missing or damaged standard safety equipment will have that equipment repaired or replaced and the customer will be charged for any such service/repairs. Customers can avoid such charges only if the missing safety component is supplied to the service center at the time of repair. This parts list is provided to aid in obtaining service parts. Copies of the instruction and maintenance literature can be obtained through the Delta Technical Publications Department or through your service outlet. Page 10/ RAS-5E /DEB