SLA DC Module SLA DC G2 50mm SNC Modules SLA ESSENCE Product description Fits in most existing MR16 / GU10 halogen luminaires Replacement of 50 W MR16 halogen lamps or 20 W HID lamp Module with integrated heatsink and optics Free choice of variable dimming and non-dimming LED Drivers Pre-wired for quick and easy installation Eye-catching lens optic with mirrors halogen facettes Module luminous efficacy up to 104 lm/w Higher CRI, typical Ra = 92 Colour temperatures 2,700 K, 3,000 K, 4,000 K High colour consistency (MacAdam 3) SLA DC G2 50mm 700lm SNC SLA DC G2 50mm 1200lm SNC Beam Angle: spot degree (24 ) or downlight (36 ) Long life-time: L70B50 >50,000 h 5-year guarantee È Standards, page 3 Colour temperatures and tolerances, page 3 1
Module SLA DC G2 50mm SNC Modules SLA ESSENCE Technical data Ambient temperature range -20... +40 C tp rated for SLA DC 700lm 60 C tp rated for SLA DC 1200lm tc for SLA DC 700lm tc for SLA DC 1200lm 90 C Irated for SLA DC 700lm 250 ma Irated for SLA DC 1200lm 350 ma Imax for SLA DC 700lm 300 ma Imax for SLA DC 1200lm 380 ma Max. permissible LF current ripple for SLA DC 700lm 900 ma Max. permissible LF current ripple for SLA DC 1200lm 1,030 ma Max. permissible peak current for SLA DC 700lm 1,260 ma / max. 10 ms Max. permissible peak current for SLA DC 1200lm 1,450 ma / max. 10 ms Max. working voltage for insulation SELV 60 V Insulation test voltage 0.5 kv ESD classification severity level 2 Risk group (EN 62471:2008) RG1 of protection IP20 60 70 tc, tp tc, tp ø49,6 ø49,6 SLA DC G2 50mm 700lm SLA DC G2 50mm 1200lm tc, tp... red marked Ordering data Article number Colour temperaturepackaging Weight per pc. SLA DC G2 50mm 700lm 927 24D SNC 28001942 2,700 K 80 pc(s). 0.090 kg SLA DC G2 50mm 700lm 927 36D SNC 28001943 2,700 K 80 pc(s). 0.090 kg SLA DC G2 50mm 700lm 930 24D SNC 28001944 3,000 K 80 pc(s). 0.090 kg SLA DC G2 50mm 700lm 930 36D SNC 28001945 3,000 K 80 pc(s). 0.090 kg SLA DC G2 50mm 700lm 940 24D SNC 28001946 4,000 K 80 pc(s). 0.090 kg SLA DC G2 50mm 700lm 940 36D SNC 28001947 4,000 K 80 pc(s). 0.090 kg SLA DC G2 50mm 1200lm 927 24D SNC 28001950 2,700 K 80 pc(s). 0.101 kg SLA DC G2 50mm 1200lm 927 36D SNC 28001951 2,700 K 80 pc(s). 0.101 kg SLA DC G2 50mm 1200lm 930 24D SNC 28001952 3,000 K 80 pc(s). 0.101 kg SLA DC G2 50mm 1200lm 930 36D SNC 28001953 3,000 K 80 pc(s). 0.101 kg SLA DC G2 50mm 1200lm 940 24D SNC 28001954 4,000 K 80 pc(s). 0.101 kg SLA DC G2 50mm 1200lm 940 36D SNC 28001955 4,000 K 80 pc(s). 0.101 kg Specific technical data Photometric code Forward current Luminous flux at tp rated 1 Typ. intensity at tp rated 1 Beam characteristics Power consumption at tp rated 1 Min. forward voltage at tc 1 Max. forward voltage at ta = -20 C 1 Efficacy at tp rated SLA DC G2 50mm 700lm 927 24D SNC 927/359 250 ma 770 lm 2,920 cd 24 8.8 W 30.0 V 40.0 V 88 lm/w > 90 SLA DC G2 50mm 700lm 927 36D SNC 927/359 250 ma 770 lm 1,540 cd 36 8.8 W 30.0 V 40.0 V 88 lm/w > 90 SLA DC G2 50mm 700lm 930 24D SNC 930/359 250 ma 840 lm 3,190 cd 24 8.8 W 30.0 V 40.0 V 95 lm/w > 90 SLA DC G2 50mm 700lm 930 36D SNC 930/359 250 ma 840 lm 1,680 cd 36 8.8 W 30.0 V 40.0 V 95 lm/w > 90 SLA DC G2 50mm 700lm 940 24D SNC 940/359 250 ma 890 lm 3,380 cd 24 8.8 W 30.0 V 40.0 V 101 lm/w > 90 SLA DC G2 50mm 700lm 940 36D SNC 940/359 250 ma 890 lm 1,780 cd 36 8.8 W 30.0 V 40.0 V 101 lm/w > 90 SLA DC G2 50mm 1200lm 927 24D SNC 927/349 350 ma 1,140 lm 4,300 cd 24 12.2 W 32.4 V 37.6 V 93 lm/w > 90 SLA DC G2 50mm 1200lm 927 36D SNC 927/349 350 ma 1,140 lm 2,200 cd 36 12.2 W 32.4 V 37.6 V 93 lm/w > 90 SLA DC G2 50mm 1200lm 930 24D SNC 930/349 350 ma 1,170 lm 4,400 cd 24 12.2 W 32.4 V 37.6 V 96 lm/w > 90 SLA DC G2 50mm 1200lm 930 36D SNC 930/349 350 ma 1,170 lm 2,300 cd 36 12.2 W 32.4 V 37.6 V 96 lm/w > 90 SLA DC G2 50mm 1200lm 940 24D SNC 940/349 350 ma 1,270 lm 4,800 cd 24 12.2 W 32.4 V 37.6 V 104 lm/w > 90 SLA DC G2 50mm 1200lm 940 36D SNC 940/349 350 ma 1,270 lm 2,500 cd 36 12.2 W 32.4 V 37.6 V 104 lm/w > 90 1 Tolerance range for optical and electrical data: ±10 %. Colour rendering index CRI Data sheet 12/17-LED388-4 www.tridonic.com 2
ACCES- SORIES ACS TRIM RING Product description Up to 30 swivel mounting rings for ceiling cutouts 68 mm and 75 mm Matt white / matt black / brushed nickel finishing Version 75 mm with optional anti-glare guard Spring clip pre-assembled ACS TRIM RING SWIVEL 75mm WH LO 30 ACS TRIM RING SWIVEL 75mm BK 30 ø90 ø62,9 ø48,5 21,2 ACS TRIM RING SWIVEL 75mm BN LO 30 ACS TRIM RING SWIVEL 68mm 30 ø89 ø67,7 ø47,8 22,2 ø92 ø72,3 ø40 40 ACS TRIM RING SWIVEL 75mm LO 30 ACS TRIM RING SWIVEL 75mm 30 Ordering data Article number Colour Ceiling cutout Packaging carton Weight per pc. ACS TRIM RING SWIVEL 68mm WH 30 28002184 White ø 68 mm 90 pc(s). 0.072 kg ACS TRIM RING SWIVEL 68mm BK 30 28002185 Black ø 68 mm 90 pc(s). 0.072 kg ACS TRIM RING SWIVEL 68mm BN 30 28002186 Chrome ø 68 mm 90 pc(s). 0.072 kg ACS TRIM RING SWIVEL 75mm WH LO 30 28002181 White ø 75 mm 90 pc(s). 0.073 kg ACS TRIM RING SWIVEL 75mm BK LO 30 28002182 Black ø 75 mm 90 pc(s). 0.073 kg ACS TRIM RING SWIVEL 75mm BN LO 30 28002183 Chrome ø 75 mm 90 pc(s). 0.073 kg ACS TRIM RING SWIVEL 75mm WH 30 28002187 White ø 75 mm 90 pc(s). 0.100 kg ACS TRIM RING SWIVEL 75mm BK 30 28002188 Black ø 75 mm 90 pc(s). 0.100 kg Data sheet 12/17-LED388-4 3
1. Standards EN 62031 EN 62471 EN 61547 1.1 Photometric code Key for photometric code, e. g. 930 / 349 1 st digit 2 nd + 3 rd digit 4 th digit 5 th digit 6 th digit Luminous flux after 25% Code CRI McAdam after of the life-time (max.6000h) Colour temperature in McAdam 25% of the Code Luminous flux 7 70 79 initial life-time 7 70 % Kelvin x 100 8 80 89 (max.6000h) 8 80 % 9 90 9 90 % 1.2 Energy classification 3. Installation / wiring 3.1 Electrical supply/choice of LED Driver SLA modules from Tridonic are not protected against overvoltages, overcurrents, overloads or short-circuit currents. Safe and reliable operation can only be guaranteed in conjunction with a LED Driver which complies with the relevant standards. The use of LED Drivers from Tridonic in combination with SLA modules guarantees the necessary protection for safe and reliable operation. If a LED Driver other than Tridonic is used, it must provide the following protection: Short-circuit protection Overload protection Overtemperature protection SLA modules must be supplied by a constant current LED Driver. Operation with a constant voltage LED Driver will lead to an irreversible damage of the module. Wrong polarity can damage the SLA. Energy classification SLA DC G2 50mm 700lm 927 SNC A+ SLA DC G2 50mm 700lm 930 SNC A+ SLA DC G2 50mm 700lm 940 SNC A++ SLA DC G2 50mm 1200lm 927 SNC A+ SLA DC G2 50mm 1200lm 930 SNC A+ SLA DC G2 50mm 1200lm 940 24D SNC A++ SLA DC G2 50mm 1200lm 940 36D SNC A+ 3.2 wiring 2. Thermal details 2.1 tp point, ambient temperature and life-time The temperature at tp reference point is crucial for the light output and life-time of a LED product. For SLA DC G2 700lm a tp temperature of 60 C and for SLA DC G2 1200lm a tp temperature of has to be complied in order to achieve an optimum between light output and life-time. Compliance with the maximum permissible reference temperature at the tc point must be checked under operating conditions in a thermally stable state. The maximum value must be determined under worst-case conditions for the relevant application. Red: + Black: 3.3 Wiring type and cross section Cable type: VDE HO3VVH2-F 0.5 mm² Cable length: 460 mm Stripping length: 8 mm, pre-tinned The tc and tp temperature of LED modules from Tridonic are measured at the same reference point. 2.2 Storage and humidity storage temperature -30... +80 C L N + +... red... black Operation only in non condensing environment. Humidity during processing of the module should be < 85 %. LED Driver 2.3 Thermal design and heat sink The rated life of LED products depends to a large extent on the temperature. If the permissible temperature limits are exceeded, the life of the SLA will be greatly reduced or the SLA may be destroyed. Data sheet 12/17-LED388-4 www.tridonic.com 4
3.4 Mounting instruction 3.5 EOS/ESD safety guidelines >70 / 80 60 / 70 >40 ø49,6 tc, tp 50 The device / module contains components that are sensitive to electrostatic discharge and may only be installed in the factory and on site if appropriate EOS/ESD protection measures have been taken. No special measures need be taken for devices/modules with enclosed casings (contact with the pc board not possible), just normal installation practice. For further information for EOS/ESD safety guidlines and the ESD classification please refer to the brochure entitled http://www.tridonic.com/esd-protection. For mounting the SLA products it is necessary to have a assemble ring which is not provided. Chemical substance may harm the LED module. Chemical reactions could lead to colour shift, reduced luminous flux or a total failure of the module caused by corrosion of electrical connections. 4. Life-time 4.1 Life-time, lumen maintenance and failure rate The light output of an LED Module decreases over the life-time, this is characterized with the L value. L70 means that the LED module will give 70 % of its initial luminous flux. This value is always related to the number of operation hours and therefore defines the life-time of an LED module. As the L value is a statistical value and the lumen maintenace may vary over the delivered LED modules. The B value defines the amount of modules which are below the specific L value, e.g. L70B10 means 10 % of the LED modules are below 70 % of the inital luminous flux, respectivly 90 % will be above 70 % of the initial value. n addition the percentage of failed modules (fatal failure) is characterized by the C value. The F value is the combination of the B and C value. That means for F degradation and complete failures are considered, e.g. L70F10 means 10 % of the LED modules may fail or be below 70 % of the initial luminous flux. 4.2 Lumen maintenance SLA DC 700lm: Forward current tp temperature L90B50 L90B10 L80B50 L80B10 L70B50 L70B10 180 ma 250 ma 50 C 14,000 h 8,000 h 31,000 h 25,000 h >50,000 h 42,000 h 65 C 14,000 h 8,000 h 31,000 h 25,000 h >50,000 h 42,000 h 60 C 14,000 h 8,000 h 31,000 h 25,000 h >50,000 h 42,000 h 13,000 h 8,000 h 31,000 h 25,000 h >50,000 h 42,000 h SLA DC 1200lm: Forward current tp temperature L90B50 L90B10 L80B50 L80B10 L70B50 L70B10 250 ma 350 ma 55 C >50,000 h >50,000 h >50,000 h >50,000 h >50,000 h >50,000 h 70 C >50,000 h >50,000 h >50,000 h >50,000 h >50,000 h >50,000 h >50,000 h >50,000 h >50,000 h >50,000 h >50,000 h >50,000 h 90 C >50,000 h >50,000 h >50,000 h >50,000 h >50,000 h >50,000 h Data sheet 12/17-LED388-4 5
LED Driver Compact dimming Driver LCA 10W 150 400mA one4all SR PRE PREMIUM series Product description Independent dimmable LED Driver Adjustable output current between 150 and 400 ma via ready2mains Programmer, I-select 2 plugs or DALI Max. output power 10 W Up to 82 % efficiency Power input on stand-by < 0.2 W Dimming range 1 100 % Nominal life-time up to 100,000 h 5-year guarantee Housing properties Casing: polycarbonate, white of protection IP20 Interfaces one4all (DALI-2 DT 6, DSI, switchdim, corridorfunction) ready2mains (configuration and dimming via mains) Terminal blocks: 0 push terminals Functions Adjustable output current (DALI, ready2mains, I-select 2) Constant light output function (CLO) Power-up fading at AC Configurable via ready2mains Service monitor to log certain events Protective features (overtemperature, short-circuit, overload, no-load, input voltage range, reduced surge amplification) Suitable for emergency escape lighting systems acc. to EN 50172 Benefits Application-oriented operating window for maximum compatibility Best energy savings due to low standby losses and high efficiency Flexible configuration via DALI, ready2mains and I-select 2 Reliability proven by life-time up to 100,000 h and 5-year guarantee Typical applications For spot light and downlight in retail and hospitality applications È Standards, page 4 Data sheet 03/18-LC338-6 www.tridonic.com 1
LED Driver Compact dimming EL Driver LCA 10W 150 400mA one4all SR PRE PREMIUM series 220 240 V Input voltage, AC 198 264 V Input voltage, DC 176 280 V Mains frequency 0 / 50 / 60 Hz Overvoltage protection 320 V AC, 48 h Typ. current (at 230 V, 50 Hz, full load)1 2 35 60 ma ø7 5 Rated supply voltage 31 Technical data 200 < 700 µa Max. input power 13 W Typ. efficiency (at 230 V / 50 Hz / full load)2 82 % λ (at 230 V, 50 Hz, full load)1 0.96 Typ. power input on stand-by3 < 0.2 W Typ. input current in no-load operation 12.4 ma Typ. input power in no-load operation < 0.5 W In-rush current (peak / duration) 15 A / 243 μs THD (at 230 V, 50 Hz, full load)1 < 10 % Time to light (at 230 V, 50 Hz, full load)1 < 0.7 s Time to light (DC mode) < 0.4 s Switchover time (AC/DC) < 0.4 s Turn off time (at 230 V, 50 Hz, full load) < 20 ms Output current tolerance1 6 ±3% Max. output current peak (non-repetitive) output current + 40 % Output LF current ripple (< 120 Hz) ±5% Max. output voltage (no-load voltage) 60 V Dimming range 1 100 % Mains surge capability (between L N) 1 kv Mains surge capability (between L/N PE) 2 kv Surge voltage at output side (against PE) < 500 V Dimensions L x W x H 200 x 70 x 31 mm 70 Leakage current (at 230 V, 50 Hz, full load)1 2 Ø4.2 Typ. current (220 V, 0 Hz, full load, 15 % dimming level)2 10 20 ma 5 Ordering data Article number Packaging carton Packaging pallet Weight per pc. LCA 10W 150-400mA one4all SR PRE 28000669 10 pc(s). 400 pc(s). 0.203 kg Specific technical data Output Min. forward Max. forward Max. output Typ. power consumption Typ. current consumption Max. casing Ambient I-select 2 voltage power (at 230 V, 50 Hz, full load) (at 230 V, 50 Hz, full load) temperature tc temperature ta max. resistor value5 current4 6 voltage LCA 10W 150-400mA one4all SR PRE 1 Valid 150 ma 40 V 6W 8.2 W 37 ma open 200 ma 40 V 8W 10.4 W 46 ma 25.00 kω 20.00 kω 250 ma 40 V 10 W 12.5 W 55 ma 300 ma 34 V 10 W 12.5 W 55 ma 16.67 kω 350 ma 29 V 10 W 12.3 W 54 ma 14.29 kω 400 ma 25 V 10 W 12.2 W 54 ma short circuit (0 Ω) at 100 % dimming level. 2 Depending on the selected output current. 3 Depending on the DALI traffic at the interface. 4 The table only lists a number of possible operating points but does not cover each single point. The output current can be set within the total value range in 1-mA-steps. 5 Not compatible with I-select (generation 1). 6 Output current is mean value. Data sheet 03/18-LC338-6 www.tridonic.com 2
LED Driver Compact dimming ACCES- SORIES I-SELECT 2 PLUG PRE / EXC Product description Ready-for-use resistor to set output current value Compatible with LED Driver featuring I-select 2 interface; not compatible with I-select (generation 1) Resistor is base isolated Resistor power 0.25 W Current tolerance ± 2 % to nominal current value Compatible with LED Driver series PRE and EXC 5,5 4,5 9 xxxx xxxx 7,5 13,5 Example of calculation R [kω] = 5 V / I_out [ma] x 1000 Resistor value tolerance 1 %; resistor power 0.1 W; base isolation necessary When using a resistor value beyond the specified range, the output current will automatically be set to the minimum value (resistor value too big), respectively to the maximum value (resistor value too small) Ordering data Article number Colour Marking Current Resistor value 3,5 Packaging bag Weight per pc. I-SELECT 2 PLUG 150MA BL 28001102 Blue 0150 ma 150 ma 33.33 kω 10 pc(s). 0.001 kg I-SELECT 2 PLUG 200MA BL 28001104 Blue 0200 ma 200 ma 25.00 kω 10 pc(s). 0.001 kg I-SELECT 2 PLUG 225MA BL 28001105 Blue 0225 ma 225 ma 22.22 kω 10 pc(s). 0.001 kg I-SELECT 2 PLUG 250MA BL 28001106 Blue 0250 ma 250 ma 20.00 kω 10 pc(s). 0.001 kg I-SELECT 2 PLUG 275MA BL 28001107 Blue 0275 ma 275 ma 18.18 kω 10 pc(s). 0.001 kg I-SELECT 2 PLUG 300MA BL 28001108 Blue 0300 ma 300 ma 16.67 kω 10 pc(s). 0.001 kg I-SELECT 2 PLUG 325MA BL 28001109 Blue 0325 ma 325 ma 15.38 kω 10 pc(s). 0.001 kg I-SELECT 2 PLUG 350MA BL 28001110 Blue 0350 ma 350 ma 14.29 kω 10 pc(s). 0.001 kg I-SELECT 2 PLUG 375MA BL 28001111 Blue 0375 ma 375 ma 13.33 kω 10 pc(s). 0.001 kg I-SELECT 2 PLUG 400MA BL 28001112 Blue 0400 ma 400 ma 12.50 kω 10 pc(s). 0.001 kg I-SELECT 2 PLUG MAX BL 28001099 Blue MAX MAX 0.00 kω 10 pc(s). 0.001 kg Data sheet 03/18-LC338-6 www.tridonic.com 3