Study on Pre-Warning Method of the Lateral Security of Heavy Vehicle in Deteriorative Weather

Similar documents
Open Access The New Structure Design and Simulation of Preventing Electric Shock Multi-Jacks Socket

Research of Driving Performance for Heavy Duty Vehicle Running on Long Downhill Road Based on Engine Brake

Study on Tractor Semi-Trailer Roll Stability Control

Research on Optimization for the Piston Pin and the Piston Pin Boss

Kinematics and Force Analysis of Lifting Mechanism of Detachable Container Garbage Truck

Analytical impact of the sliding friction on mesh stiffness of spur gear drives based on Ishikawa model

A Simulation Model of the Automotive Power System Based on the Finite State Machine

Correlation of Occupant Evaluation Index on Vehicle-occupant-guardrail Impact System Guo-sheng ZHANG, Hong-li LIU and Zhi-sheng DONG

Investigation on Emergency Brake Property of a Heavy-Duty Vehicle Based on Functional Virtual Prototyping Model

Open Access Co-Simulation and Experimental Research of Wedge Broken-Belt Catching Device

Influence of Coupler and Buffer on Dynamics Performance of Heavy Haul Locomotive

Research on vibration reduction of multiple parallel gear shafts with ISFD

Transverse Distribution Calculation and Analysis of Strengthened Yingjing Bridge

Design of Damping Base and Dynamic Analysis of Whole Vehicle Transportation based on Filtered White-Noise GongXue Zhang1,a and Ning Chen2,b,*

Characteristics of wheel-rail vibration of the vertical section in high-speed railways

The Testing and Data Analyzing of Automobile Braking Performance. Peijiang Chen

Design of Active Safety Warning System for Hazardous Chemical Transportation Vehicle

Available online at ScienceDirect. Procedia Engineering 137 (2016 ) GITSS2015

Analysis on natural characteristics of four-stage main transmission system in three-engine helicopter

Open Access Study on Synchronous Tracking Control with Two Hall Switch-type Sensors Based on Programmable Logic Controller

Research of the vehicle with AFS control strategy based on fuzzy logic

Open Access Calculation for the Heating and Safe Operation Time of YKK Series Highvoltage Motors in Starting Process

Modal Analysis of Automobile Brake Drum Based on ANSYS Workbench Dan Yang1, 2,Zhen Yu1, 2, Leilei Zhang1, a * and Wentao Cheng2

Structure Parameters Optimization Analysis of Hydraulic Hammer System *

Braking Performance Improvement Method for V2V Communication-Based Autonomous Emergency Braking at Intersections

Technology, Xi an , China

Design and experiment of hydraulic impact loading system for mine cable bolt

NUMERICAL ANALYSIS OF IMPACT BETWEEN SHUNTING LOCOMOTIVE AND SELECTED ROAD VEHICLE

Collaborative vehicle steering and braking control system research Jiuchao Li, Yu Cui, Guohua Zang

A Brake Pad Wear Control Algorithm for Electronic Brake System

Perodua Myvi engine fuel consumption map and fuel economy vehicle simulation on the drive cycles based on Malaysian roads

Special edition paper

Study on V2V-based AEB System Performance Analysis in Various Road Conditions at an Intersection

METHOD FOR TESTING STEERABILITY AND STABILITY OF MILITARY VEHICLES MOTION USING SR60E STEERING ROBOT

Full Scale Experimental Evaluation for Cable Dampers

Power Matching Strategy Modeling and Simulation of PHEV Based on Multi agent

International Conference on Mechanics, Materials and Structural Engineering (ICMMSE 2016)

Lateral Stability Analysis of Telehandlers Based on Multibody Dynamics

China. Keywords: Electronically controled Braking System, Proportional Relay Valve, Simulation, HIL Test

Rigid-Flexible Coupling Dynamics Simulation Analysis of Wheel/Rail Interaction in High-speed Turnout Zone

Prediction of wheel/rail rolling contact wear under the situation of wheel/rail vibration

The spray characteristic of gas-liquid coaxial swirl injector by experiment

Dynamic Characteristics Analysis of H-Type Leg Hydraulic System of. Truck mounted Concrete Pump

Application of Airborne Electro-Optical Platform with Shock Absorbers. Hui YAN, Dong-sheng YANG, Tao YUAN, Xiang BI, and Hong-yuan JIANG*

AEB System for a Curved Road Considering V2Vbased Road Surface Conditions

Parameters Matching and Simulation on a Hybrid Power System for Electric Bulldozer Hong Wang 1, Qiang Song 2,, Feng-Chun SUN 3 and Pu Zeng 4

A Numerical Investigation of a Novel Hood Design for Pedestrian Protection

Application of Soft Magnetic Composite Material in the Field of Electrical Machines Xiaobei Li 1,2,a, Jing Zhao 1,2,b*, Zhen Chen 1,2, c

Study on the Performance of Lithium-Ion Batteries at Different Temperatures Shanshan Guo1,a*,Yun Liu1,b and Lin Li2,c 1

Research on Skid Control of Small Electric Vehicle (Effect of Velocity Prediction by Observer System)

The Design of Vehicle Tire Pressure Monitoring System Based on Bluetooth

Optimization Design of the Structure of the Manual Swing-out Luggage Compartment Door of Passenger Cars

Chapter 2 Dynamic Analysis of a Heavy Vehicle Using Lumped Parameter Model

Chapter 2 Analysis on Lock Problem in Frontal Collision for Mini Vehicle

1036. Thermal-hydraulic modelling and analysis of hydraulic damper for impact cylinder with large flow

Temperature Field in Torque Converter Clutch

Study on State of Charge Estimation of Batteries for Electric Vehicle

ANALYSIS ON MECHANICAL PARAMETERS OF LUNAR ROVER WHEEL

Design and Application of Versatile Automatic Bin with Valve Splint Slide Way

A study of the minimum safe stopping distance between vehicles in terms of braking systems, weather and pavement conditions

MARINE FOUR-STROKE DIESEL ENGINE CRANKSHAFT MAIN BEARING OIL FILM LUBRICATION CHARACTERISTIC ANALYSIS

THE NON-LINEAR STRENGTH-WORK OF ALL BODY CONSTRUCTIONS THE HELICOPTER IS - 2 DURING FAILURE LANDING

Design and Analysis of Electromagnetic Tubular Linear Actuator for Higher Performance of Active Accelerate Pedal

DESIGN METHODS FOR SAFETY ENHANCEMENT MEASURES ON LONG STEEP DOWNGRADES

[Type text] [Type text] [Type text] Zhang Zenglian 1 School of Automobile and Traffic Engineering, Jiangsu University, Zhenjiang,

Parametric Design and Motion Analysis of Geneva Wheel Mechanism Based on the UG NX8.5

The Modeling and Simulation of DC Traction Power Supply Network for Urban Rail Transit Based on Simulink

Open Access Application of Super Capacitor in HEV Regenerative Braking System

Experimental investigation on vibration characteristics and frequency domain of heavy haul locomotives

Analysis of Flow Field for Automotive Exhaust System Based on Computational Fluid Dynamics

Research on Optimization of Bleed Air Environment Control System of Aircraft Xin-ge WANG, Han BAO* and Kun-wu YE

CAUSE ANALYSIS OF TRAFFIC CRASHES BLACK SPOTS ON HIGHWAY LONG STEEP DOWNGRADES IN CHINA

Dynamic Responses of Rotor Drops onto Auxiliary Bearing with the Support of Metal Rubber Ring

Research on Damping Characteristics of Magneto-rheological Damper Used in Vehicle Seat Suspension

Study of Flexible Wheels for Lunar Exploration Rovers: Running Performance of Flexible Wheels with Various Amount of Deflection

Passive Vibration Reduction with Silicone Springs and Dynamic Absorber

Pantograph and catenary system with double pantographs for high-speed trains at 350 km/h or higher

Research on Machine Tool Spindle System with Embedded FBG Temperature Sensors

Fuzzy based Adaptive Control of Antilock Braking System

Stability Models of Heavy Vehicle

The Theoretical Analysis of Test Result s Errors for the Roller Type Automobile Brake Tester

Available online at ScienceDirect. Procedia Technology 21 (2015 ) SMART GRID Technologies, August 6-8, 2015

Muti-objective topology optimization of an electric vehicle s traction battery enclosure

A Measuring Method About the Bullet Velocity in Electromagnetic Rail Gun

Research on Collision Characteristics for Rear Protective Device of Tank Vehicle Guo-sheng ZHANG, Lin-sen DU and Shuai LI

A Model of Wind Turbine s Flexibility Shaft

Design and Manufacture of Heavy Truck Braking Spray Device Based on PLCS7-200

Analysis and Design of the Super Capacitor Monitoring System of Hybrid Electric Vehicles

Dynamic Simulation of the Impact Mechanism of Hydraulic Rock Drill Based on AMESim Yin Zhong-jun 1,a, Hu Yi-xin 1,b

Experimental Investigation of Effects of Shock Absorber Mounting Angle on Damping Characterstics

Optimum Matching of Electric Vehicle Powertrain

The Simulation of Metro Wheel Tread Temperature in Emergency Braking Condition Hong-Guang CUI 1 and Guo HU 2*

ScienceDirect. Evaluation of track design and track geometry of the track with unconventional structure of railway superstructure

Bond Graph Modeling and Simulation Analysis of the Electro-Hydraulic Actuator in Non-Load Condition

The Test System Design and Actual Test of Motor Axis Torque During Seamless Steel Tube Rolling

Research on Electric Hydraulic Regenerative Braking System of Electric Bus

Experimental Study on Torsional Vibration of Transmission System Under Engine Excitation Xin YANG*, Tie-shan ZHANG and Nan-lin LEI

Featured Articles Utilization of AI in the Railway Sector Case Study of Energy Efficiency in Railway Operations

Vibration Analysis of Gear Transmission System in Electric Vehicle

Matching Design of Power Coupling for Two-Motor-Drive Electric Vehicle Lin Cheng1, a, Zhang Ru1, a, Xu Zhifeng1, a, Wang Gang1, a

Transcription:

Send Orders for Reprints to reprints@benthamscience.ae 292 The Open Mechanical Engineering Journal, 2014, 8, 292-296 Open Access Study on Pre-Warning Method of the Lateral Security of Heavy Vehicle in Deteriorative Weather Zhi-Guo Zhao *,1,2, Min Chen 1, Nan Chen 1, Yong-Bing Zhao 2 and Xin Chen 2 1 School of Mechanical Engineering, Southeast University, Nanjing, China 2 School of Transportation Engineering, Huaiyin Institute of Technology, Huaian, China Abstract: The lateral security of heavy vehicle in deteriorative weather is one of the main causes of accidents of vehicles on roads. Road safety has become a subject of great concern to institutions of higher education and scientific research institutions. There are important theoretical and practical significances to explore applicable and effective lateral safety warning methods of heavy vehicles. One of the purposes of this paper is to provide a good theoretical basis for the core technology of heavy vehicle safety features for our country's independent research and development. Aiming at the issue of lateral security of heavy vehicle for road conditions in deteriorative weather, this paper constructs the framework of the lateral security pre-warning system of heavy vehicles based on cooperative vehicle infrastructure. Moreover, it establishes vehicle lateral security statics model through analysis of the force of the car in the slope with section bending and states the parameters of vehicles for no rollover. The side slip is indexed to calculate critical speed of vehicles in a bend. This paper also analyzes the influence of road friction coefficient, the road gradient and the turning radius on the lateral security of the vehicle with critical speed on the asphalt pavement with surface conditions ranging from wet, dry, snowing or icy. The calculation results show that the bad weather road conditions, road friction coefficient and turning radius have obvious influence on the lateral security critical speed. Experimental results indicate that the critical speed error warning is within 4% and it meets the design requirements. Keywords: Cooperative vehicle infrastructure, Deteriorative weather, Heavy vehicle, Rollover, Side slip, The lateral security. 1. INTRODUCTION Traffic system is a complex system. In the worst weather conditions, road friction decreases, due to which vehicles more often tend to be out of the driver s control [1, 2]. In heavy trucks, there is a high center of gravity, large loading capacity and the aspect ratio is relatively large. When the vehicles turn onto unfamiliar roads, since the drivers are not familiar with the road information and conditions, excessive speed and unexpected turn radius can cause the vehicles to easily sideslip and rollover [3]. Therefore, environmental information for vehicle safety is very important. As an important part of intelligent traffic system, vehicle-road collaboration infrastructure is very important to improve vehicle safety and realize the sustainable development of transportation system. Cooperative vehicle infrastructure has become a cuttingedge technology and a research hotspot in the international intelligent transportation field. Europe and the United States and other developed regions promote the study of Propulsion technology positively [4-6]. This paper studied the lateral security of heavy vehicles and made the state parameters of vehicles to avoid rollover and prepares side slip index to calculate critical speed of vehicles in bends, as a means to *Address correspondence to this author at the School of mechanical engineering, Southeast University, Nanjing, China; Tel: 0517-83559165; Fax: 0517-83559167; E-mails: lnzzg98@163.com, 51066347@qq.com 1874-155X/14 simulate lateral security situation of the vehicles in the dry wet or icy asphalt pavement conditions. It also analyzes the influence of road friction coefficient, road gradient and turning radius on the lateral security critical speed under different weather conditions. 2. THE FRAMEWORK OF THE LATERAL SECURITY PRE-WARNING SYSTEM OF HEAVY VEHICLES BASED ON COOPERATIVE VEHICLE INFRASTRUCTURE Fig. (1) represents a systematic diagram of the lateral security pre-warning system of heavy vehicles based on cooperative vehicle infrastructure; the system consists of the roadside equipment, roadside wireless transmitter module, wireless receiver module and vehicle warning system. It broadcasts road information by wireless transmitter module installed on the roadside. This information is transmitted to the vehicle mounted unit, which in turn transmits back the vehicle information and real-time speed of the vehicle to the road side wireless transmitter module. It calculates the safest bend speed limit depending on the weather conditions and informs the driver of the optimum approach speed limit near the bend. 3. CALCULATION OF THE LATERAL SECURITY CRITICAL SPEED OF VEHICLES PARAMETERS CONSIDERING THE EFFECT OF ROAD At present, dynamics model for rollover/sideslip generally adopts the vehicles as a quasi-static model having 2014 Bentham Open

Lateral Security of Heavy Vehicle in Deteriorative Weather The Open Mechanical Engineering Journal, 2014, Volume 8 293 a rigid body. For the calculation of critical speed for the lateral security of vehicles on a bend, the model ignores deformation of vehicle suspension and flexible deformation of tires [7, 8]. The analysis of literature [9] shows that comparison of the rigid vehicles with suspension vehicles demonstrates the rollover thresholds of both of them as being close. Therefore, this paper adopts the static model and neglects suspension deformation, as shown in Fig. (2). In the diagram, F C is the centrifugal force, F f is the lateral friction, θ is the road transverse slope angle, B is the distance between the center of the two tires on either side of the vehicle, h g is the height of the center of gravity, G is the total gravity of vehicle. u chmax! gr( f " tan#) f tan# + 1 3.2. Critical Speed of Index for No Rollover According to quasi-static model of vehicle shown in Fig. (2), the vehicle does not rollover while vehicle rollover torque is less than the stability torque, that is: (F c cos! + G sin!)h g " (G cos! # F c sin!)b 2 Feeding F c into formula (3), we can get: u cf max! gr(b " tan#) + B tan# (2) (3) (4) 3.3. Analysis of Critical Speed of Driving Safety Comparing roll with sideslip, the consequences are more serious. Therefore, considering the driving safety, the slip should occur before the rollover, that is: u chmax! u cf max (5) Fig. (1). The framework of the lateral security pre-warning system of heavy vehicles based on cooperative vehicle infrastructure. When the vehicle is in sideslip, the speed will not increase, and the rollover phenomenon would not happen. Inserting formula (2) and formula (4) into formula (5), we can get: gr( f cos! " sin!) f sin! + cos! # gr(b cos! " sin!) cos! + B sin! (6) That is: f! B i 1+ tg 2 " 1# tg 2 " (7) Fig. (2). Force analytical graph of heavy truck on the side slope when steering. 3.1. Critical Speed of Index for No Sideslip According to quasi-static model of vehicle shown in Fig. (2), the necessary condition of no sideslip is that vehicle lateral force is less than the lateral friction, that is F c cos! + G sin! " F f = (G cos! # F c sin!) f (1) where, F c = mu2 u is the speed of vehicle, R is the radius R of bend, f is the road friction coefficient. Inserting F c into formula (1), we can get: For general dry asphalt pavement, f is in the range of 0.6-0.8. Therefore, in the process of using and designing vehicles, the height of the center of gravity should be lowered in order to meet the requirements of formula (7). 4. ANALYSIS OF INFLUENCE OF ROAD PARAMETERS ON THE LATERAL SECURITY CRITICAL SPEED OF VEHICLES 4.1. Basic Parameters At full load, the height of the center of gravity, h g, is 1360mm, B is 1860 mm, acceleration of gravity, g, is 9.81m/s 2, the road transverse slope angle θ is 1.15, radius of curve R is 125 m. Road friction coefficient in deteriorative weather is shown in Table 1 below. Table 1. Road friction coefficient of road conditions in deteriorative weather. Weather Conditions Friction Coefficient Dry asphalt pavement 0.6 Rainy pavement 0.4 Snowy pavement 0.28 Icy pavement 0.18

294 The Open Mechanical Engineering Journal, 2014, Volume 8 Zhao et al. 4.2. Influence of Road Friction Coefficient on the Lateral Inserting the basic parameters of road and vehicles into formula (2) and formula (4), the critical speed for rollover and sideslip of heavy vehicles in the road conditions of deteriorative weather can be obtained as shown in Table 2. As the formula (5) shows, the sideslip must be controlled if the rollover is to be prevented, so in order to make the vehicle turn safely, lateral security critical speed should be equal to sideslip critical speed. As shown in Table 2, with the increase of road friction coefficient, the lateral security critical speed of vehicles is greater. 4.3. Influence of of Road on the Lateral In order for the rain water to drain, pavement and road should have certain transverse slopes; the slope values were 1%, 1.5%, 2%, 2.5%, 3% and 3.5%. Taking pavement of rainy, snowy and icy roads for example, the influence of transverse slope on the critical speed is shown in Tables 3-5. As Tables 3-5 show that with the increase of transverse slope and decrease of road friction coefficient, the lateral security critical speed of vehicle decreases gradually. 4.4. Influence of the Road on the Lateral Different roads have different requirements for the design of turning radius; the values of turning radius were 30 m, 60 m, 125 m, 250 m and 500 m. Taking pavement of rainy, snowy and icy roads for example, the influence of turning radius on the critical speed is shown in Tables 6-8. Tables 6 and 8 show that with the increase of turning radius, the lateral security critical speed of vehicle increases and with the decrease of road friction coefficient, the lateral security critical speed of vehicle decreases. The model and pre-warning method above will be verified by remote control vehicle model test. Taking dry asphalt pavement as an example, pilot test and theoretical analysis of lateral security critical speed under different turning radiuses were analyzed. The results show that critical speed error warning is within 4% and it meets the design requirements. Table 2. The critical speed for rollover and sideslip of heavy vehicles in the road conditions of deteriorative weather. Friction Coefficient Speed 0.6 95.4 102 95.4 0.4 77.4 102 77.4 0.28 64.1 102 64.1 0.18 50.3 102 50.3 Table 3. Influence of transverse slope of road on the lateral security critical speed of vehicles on the rainy pavement. Speed 1.0 78.6 103.1 78.6 1.5 78.0 102.6 78.0 2.0 77.4 102.0 77.4 2.5 76.8 101.5 76.8 3.0 76.2 100.9 76.2 3.5 75.6 100.4 75.6 Table 4. Influence of transverse slope of road on the lateral security critical speed of vehicles on the snowy pavement. Speed 1.0 65.4 103.1 65.4 1.5 64.8 102.6 64.8 2.0 64.1 102.0 64.1 2.5 63.4 101.5 63.4 3.0 62.8 100.9 62.8 3.5 62.1 100.4 62.1

Lateral Security of Heavy Vehicle in Deteriorative Weather The Open Mechanical Engineering Journal, 2014, Volume 8 295 Table 5. Influence of transverse slope of road on the lateral security critical speed of vehicles on the icy pavement. Speed 1.0 51.9 103.1 51.9 1.5 51.1 102.6 51.1 2.0 50.3 102.0 50.3 2.5 49.5 101.5 49.5 3.0 48.7 100.9 48.7 3.5 47.9 100.4 47.9 Table 6. Influence of turning radius on the lateral security critical speed of vehicles on the rainy pavement. Speed 30 37.9 50.0 37.9 60 53.6 70.7 53.6 125 77.4 102.0 77.4 250 109.5 144.3 109.5 500 154.8 204.0 154.8 Table 7. Influence of turning radius on the lateral security critical speed of vehicles on the snowy pavement. Speed 30 31.4 50.0 31.4 60 44.4 70.7 44.4 125 64.1 102.0 64.1 250 90.7 144.3 90.7 500 128.2 204.0 128.2 Table 8. Influence of turning radius on the lateral security critical speed of vehicles on the icy pavement. Speed 30 24.7 50.0 24.7 60 34.9 70.7 34.9 125 50.3 102.0 50.3 250 71.2 144.3 71.2 500 100.7 204.0 100.7 CONCLUSION 1) This paper constructed the framework of the lateral security pre-warning system of heavy vehicles based on cooperative vehicle infrastructure. The system consisted of the roadside equipment, roadside wireless transmitter module, wireless receiver module and vehicle warning system. 2) Vehicles for no rollover and side slip were indexed to calculate critical speed of vehicles on road bends. 3) Analysis on the influence of road friction coefficient, road gradient and turning radius on the lateral security critical speed in the pavement condition of asphalt pavement with either dry rainy, snowy or icy surface was conducted. The simulation results show that in the bad weather road conditions, road friction

296 The Open Mechanical Engineering Journal, 2014, Volume 8 Zhao et al. coefficient and turning radius have obvious influence on the lateral security critical speed. CONFLICT OF INTEREST The authors confirm that this article content has no conflict of interest. ACKNOWLEDGEMENTS Research was partially sponsored by supported by the National Natural Science Foundation of China(Grant No.51205151), China Postdoctoral Science Foundation (Grant No.2013M5312471), Postdoctoral research grants program of Jiangsu Province (Grant No.1301096C) and The peak of six personnel of Jiangsu Province(Grant No.2013- ZBZZ-020). REFERENCES [1] H. Jie, and L. Xia, Influence of road condition on running safety in atrocious weather, Journal of Traffic and Transportation Engineering, vol. 1, no. 11, pp. 58-63, 2011. [2] T. R. Neuman, R. Pfefer, and K. L. Slacka, K. K. Hardy, K. Lacy, and C. Zegeer, A guide for addressing run-off-road collisions. Washington DC: American Association of State Highway and Tranportation Officials, 2003. [3] Z. Zhiguo, and W. Dongdong, Research status and development trend of side tumbing pre-warning vehicle, Journal of Hebei University of Science and Technology, vol. 2, no. 34, pp.108-112, 2013. [4] S.E. Shladover, Progressive Deployment Steps Leading Toward an Automated Highway System (AHS), Transportation Research Record No. 1727, Transportation Research Board: Washington DC, pp. 154-161, 2000. [5] R. Bishop, Intelligent vehicle applications worldwide, Intelligent Systems and their Applications, IEEE, vol. 1, no. 15, pp. 78-81, 2000. [6] W. Yunpeng, Y. Zhenguo, and X. Haiying, et al. Cooperative traffic alarming method based on epidemic model. Journal of Beijing University of Aeronautics and Astronautics, vol. 5, no. 37, pp. 515-518, 2011. [7] P. Jiabin, and W. Dalei, Probability evaluating method of bridge deck side wind effects on driving safety, China Journal of Highway and Transport, vol. 4, no. 19, pp. 59-64, 2006. [8] Y. Qunli, C. Xujun, and J. Zhaobing, Analysis of safety wind velocity of driving on sea-cross bridge based on target of no sideslip, Journal of PLA University of Science and Technology, vol. 4, no. 9, pp. 373-377, 2008. [9] L. Jing, Z. Dongdong, G. Tengfeng, Analysis for influence of large vehicles lateral stability on ultimate horizontal curve radius of highway design, China Journal of Highway and Transport, vol. Z1, no. 23, pp. 42-46, 2010. Received: July 25, 2014 Revised: August 4, 2014 Accepted: August 4, 2014 Zhao et al.; Licensee Bentham Open This is an open access article licensed under the terms of the Creative Commons Attribution Non-Commercial License (http://creativecommons.org/licenses/by-nc/4.0/) which permits unrestricted, non-commercial use, distribution and reproduction in any medium, provided the work is properly cited.