www.fabtechmtrsprts.cm 4331 EUCALYPTUS AVE ~~ CHINO, CA 91710 PHONE 909-597-7800 ** FAX 909-597-7185 1994-2001 DODGE RAM 1500 & 2500 4 WHEEL DRIVE FTS3400-50 FRONT DUAL SHOCK SYSTEM PARTS LIST: 1 EA. FT3400-50-100P DUAL SHOCK MOUNT PASSENGER S SIDE 1 EA. FT3400-50-100D DUAL SHOCK MOUNT DRIVER S SIDE 1 EA. FT3400-50-101P SUPPORT TUBE PASSENGER S SIDE 1 EA. FT3400-50-101D SUPPORT TUBE DRIVER S SIDE 1 EA. FT3400-50-102P LWR. SHOCK MNT. BRACKET PASSENGER S SIDE 1 EA. FT3400-50-102D LWR. SHOCK MNT. BRACKET DRIVER S SIDE 1 EA. FT3400-50-103P FRAME SLEEVE PASSENGER S SIDE 1 X 1 7/8 1 EA. FT3400-50-103D FRAME SLEEVE DRIVER S SIDE 1 X 2 13/16 2 EA. FT3400-50-105 LIMIT STRAPS 2 EA. FT98100-7-101 SPACER HARDWARE LIST: 8 EA. ½ X 1 ½ BOLTS 6 EA. ½ X 3 BOLTS 3 EA. ½ X 3 ½ BOLTS 1 EA. ½ X 4 BOLTS 2 EA. ½ X 4 ½ BOLTS 18 EA. 1/2 NYLOCK NUTS 36 EA. 1/2 SAE FLAT WASHERS 2 EA. 1/2 LOCK WASHERS 2 EA. ½ X 2 ½ BOLTS (t be used with ft98100-7-101 spacer) CHECK ALL PARTS INCLUDED IN THIS KIT TO THE PARTS LIST ABOVE BEFORE BEGINNING INSTALLATION OF THIS KIT. IF ANY PIECES ARE MISSING, CONTACT FABTECH AT 909-597-7800. READ ALL INSTRUCTIONS THOROUGHLY FROM START TO FINISH BEFORE BEGINNING INSTALLATION! THIS KIT MUST BE INSTALLED WITH FTS7265 FRONT SHOCKS AND FTS3400 OR FTS3420 SUSPENSION SYSTEM. O.E.M. WHEELS AND TIRES CAN BE USED AFTER THE INSTALLATION OF THIS KIT. FABTECH RECOMMEND S AFTER MARKET WHEELS WITH A MAXIMUM BACKSPACING OF 4 5/8. TOOL LIST: (NOT INCLUDED) FLOOR JACK JACK STANDS ASSORTED METRIC AND S.A.E SOCKETS DRILL WITH ¼, ½, 1 BITS
INSTRUCTIONS: 1. Discnnect the negative terminal n the battery. Jack up the frnt end f the truck and supprt the frnt frame rails with jack stands. NEVER WORK UNDER AN UNSUPPORTED VEHICLE! Remve the frnt tires. n the backside f the frame. Trque the three tp nuts t factry specs and the frnt ½ blt t 65 ft/lbs. SEE PHOTO BELOW. 2. Supprt the frnt axle with tw flr jacks. Starting n the driver s side f the truck, remve the tp nuts n the frnt shcks and the lwer blts securing the shck t the axle. Remve the three nuts securing the upper shck munt cage t the cil spring munt. Remve the frnt shcks frm the truck. Lwer the jacks under the frnt axle and remve the cil springs. 3. Place the new driver s side upper shck munt (FTS3400-50-100D) n tp f the cil twer and the three blts. Hand tighten the riginal nuts. Using a center punch, mark the center f the hle n the frnt lwer tube, n sme trucks the 1 hle will already exist n the utside f the frame, yu will still have t drill the ½ hle n the inside f the frame. Remve the three nuts securing the upper shck munt t the cil twer. Starting with a ¼ bit, drill straight thrugh bth sides f the frame. Fllw thrugh the hle with a ½ bit. Using a 1 drill, enlarge the hle n the utside f the frame t 1, DO NOT DRILL THROUGH THE INSIDE OF THE FRAME! SEE PHOTOS BELOW. 5. Take ne f the ½ x 1 ½ blts, ½ flat washers, ½ lck washers and attach the drivers side supprt tube (FTS3400-50-101D) t the side f the upper shck munt. The bttm f the supprt tube shuld rest against the tp f the bump stp tab. If the supprt tube des nt rest against the tp f the bump stp tab than use the supplied FT98100-7-101 spacer between the supprt tube and the tab. Mark the hle psitin using a center punch. Swing the supprt tube ut f the way and drill a ¼ pilt hle. Fllw thrugh with a ½ drill bit and attach the supprt tube t the bump stp tab using a ½ x 1 ½ blt, ½ flat washers and a ½ lck nut, if yu are use the supplied spacer than use the supplied ½ X 2 ½ blt in place f the 1 ½ blt.. Trque the tp and the bttm blts t 65 ft/lbs. SEE PHOTOS BELOW. 4. Place the upper shck munt back nt the cil twer. Slide the driver s side frame sleeve (2 13/16 lng) int the new 1 hle. Place a ½ x 4 blt thrugh the frnt tube f the upper shck munt, int the frame sleeve and thrugh the back f the frame. Use a ½ flat washer and lck nut
6. Psitin the lwer shck munt belw the lwer cil spring munt. Secure the bracket t the lwer cil spring munt using the supplied ½ x 1 ½ blts, ½ flat washers and ½ lck nut. Yu will need t drill ut the 2 factry hles t ½. The rear hle will use the ½ x 4 ½ blt, nut and washer, thrw the existing link arm hle. SEE PHOTO BELOW. ( PICTURE IS OF PASSENGER SIDE ) 10. Using a ½ x 3 ½ blt, ½ flat washers and lck nut, supplied in the FTS3400 r FTS3420 kit, attach the bttm f the limit strap t the new link arm munt blt. There shuld be a ½ flat washer n each side f the limit strap tab. While pulling tensin n the limit strap, trque the lwer blt t 40 ft/lbs. SEE PHOTO BELOW. 7. Repeat steps tw thrugh six n the passenger s side f the truck. The passenger s side f the truck will use the ½ x 3 ½ blt and 1 7/8 frame sleeve n the frnt tube f the upper shck munt. 8. Reinstall the cil springs int the truck the same way they were remved, raising the jacks t supprt the frnt axle. SEE PHOTO BELOW. 11. Attach the frnt shck t the munts using ½ x 3 blts, with ½ flat washers and a lck nuts. Trque all shck blts t 40 ft/lbs. SEE PHOTO BELOW AND NEXT PAGE. 9. Slide ne f the frnt shcks int the rear upper shck tabs. Take a limit strap and slide a ½ x 3 blt thrugh ne end, with a ½ flat washer n each side f the limit strap tab. Nw slide the blt thrugh the upper shck tabs and the shck. Place a flat washer and a ½ lck nut nt the blt. Attach the bttm f the shck nt the lwer shck munt with a ½ x 3 blt, with ½ flat washers and a lck nut. SEE PHOTO NEXT COLUMN.
13. Reinstall the frnt tires and trque the lugs t factry specificatins. The factry trque specificatins can be fund in yur wners manual. Set the truck back nt the grund. WHILE TURNING THE STEERING WHEEL FULLY IN EACH DIRECTION, MAKE SURE THERE IS AMPLE CLEARANCE BETWEEN THE WHEELS, TIRES, LINK ARMS, BRAKE LINES AND ABS WIRES. 14. Check frnt-end alignment and set t factry specificatins. 12. Repeat steps nine thrugh eleven n the passenger s side f the truck. The passenger s side f the truck will use the ½ x 3 ½ blt and 1 7/8 frame sleeve n the frnt tube f the upper shck munt. RETORQUE ALL NUTS, BOLTS AND LUGS AFTER 50 MILES AND PERIODICALLY THEREAFTER. Fr technical assistance call: 909-597-7800
Prduct Warranty and Warnings- Fabtech prvides a Limited Lifetime Warranty t the riginal retail purchaser wh wns the vehicle, n which the prduct was riginally installed, fr defects in wrkmanship and materials. The Limited Lifetime Warranty excludes the fllwing Fabtech items; bushings, bump stps, ball jints, tie rd ends, limiting straps, crss shafts, heim jints. These parts are subject t wear and are nt cnsidered defective when wrn. They are warranted fr 60 days frm the date f purchase fr defects in wrkmanship. Take apart shcks are cnsidered a serviceable shck with a ne year warranty n leakage nly. Service seal kits are available separately fr future maintenance. All ther shcks are cvered under ur Limited Lifetime Warranty. Fabtech des nt warrant any prduct fr finish, alteratins, mdificatins and/r installatin cntrary t Fabtech s instructins. Alteratins t the finish f the parts including but nt limited t painting, pwdercating, plating and/r welding will vid all warranties. Sme finish damage may ccur t parts during shipping which is cnsidered nrmal and is nt cvered under warranty. Fabtech prducts are nt designed nr intended t be installed n vehicles used in race applicatins r fr racing purpses r fr similar activities. (A RACE is defined as any cntest between tw r mre vehicles, r any cntest f ne r mre vehicle against the clck, whether r nt such cntest is fr a prize). This warranty des nt include cverage fr plice r taxi vehicles, race vehicles, r vehicles used fr gvernment r cmmercial purpses. Als excluded frm this warranty are sales utside f the United States f America. Installatin f mst suspensin prducts will raise the center f gravity f the vehicle and will cause the vehicle t handle differently than stck. It may increase the vehicle s susceptibility t a rllver, n rad and ff rad, at all speeds. Extreme care shuld be taken t perate the vehicle safely at all times t prevent rllver r lss f cntrl resulting in serius injury r death. Fabtech frnt end Desert Guards may impair the deplyment r peratin f vehicles equipped with supplemental restraining systems/air bag systems and shuld nt be installed if the vehicle is equipped as s. Fabtech makes every effrt t ensure suspensin prduct cmpatibility with all vehicles listed in the catalg, but due t unknwn aut manufacturers prductin changes and/r incnstancies by the aut manufacturer, Fabtech cannt be respnsible fr 100% cmpatibility, including the fitment f tire and wheel sizes listed. The Tire and Wheel sizes listed in Fabtech s catalg are nly a guideline fr street driving with nted fender trimming. Fabtech is nt respnsible fr damages t the vehicle s bdy r tires. Fabtech s bligatin under this warranty is limited t the repair r replacement, at Fabtech ptin, f the defective prduct nly. All csts f remval, installatin r re-installatin, freight charges, incidental r cnsequential damages are expressly excluded frm this warranty. Fabtech is nt respnsible fr damages and/r warranty f ther vehicle parts related r nn related t the installed Fabtech prduct. This warranty is expressly in lieu f all ther warranties expressed r implied. This warranty shall nt apply t any prduct that has been subject t accident, negligence, alteratin, abuse r misuse as determined by Fabtech. Fabtech suspensin cmpnents must be installed as a cmplete system including shcks as shwn in ur current catalg. All warranties will becme vid if Fabtech parts are cmbined and/r substituted with ther aftermarket suspensin prducts. Cmbinatin and/r substitutin f ther aftermarket suspensin parts may cause premature wear and/r prduct failure resulting in an accident causing injury r death. Fabtech des nt warrant prducts nt manufactured by Fabtech. Installatin f Fabtech prduct may vid the vehicles factry warranty; it is the cnsumer s respnsibility t check with their lcal vehicle s dealer fr warranty dispsitin befre the installatin f the prduct. It is the respnsibility f the distributr and/r the retailer t review all warranties and warnings f Fabtech prducts with the cnsumer prir t purchase. Fabtech reserves the right t supercede, discntinue, change the design, finish, part number and, r applicatin f parts when deemed necessary withut written ntice. Fabtech is nt respnsible fr misprints r typgraphical errrs within the catalg r price sheet. Instructin Sheet Part #- FT3400-50i 07/07/08AM