INSTALLATION INSTRUCTIONS Accessory P/N 08L96-SZA-100A Application 2015 PILOT Publications No. AII 51544 Issue Date MAY 2014 PARTS LIST Advanced cargo net 2 Anchors A (Large) 4 Anchors B 6 Self-tapping screws TOOLS AND SUPPLIES REQUIRED Drill 3 mm, 5 mm, and 10.5 mm Drill bits Masking tape Tape Felt-tip pen Scale Small flat-tip screwdriver Eye protection (face shield, safety goggles, etc.) INSTALLATION Customer Information: The information in this installation instruction is intended for use only by skilled technicians who have the proper tools, equipment, and training to correctly and safely add equipment to your vehicle. These procedures should not be attempted by do-it-yourselfers. NOTE: This advanced cargo net cannot be installed with the cargo liner or interior bicycle attachment. Installing the Hooks 1. Using a small flat-tip screwdriver, push and release the seat belt lower hook from each third row seat. Insert the seat belt lower hooks into the side slots. 4 Snaps Push. LOWER HOOK SEAT BELT Accessory User s Information Manual LOWER HOOK SIDE SLOT 2014 American Honda Motor Co., Inc. All Rights Reserved. AII 51544 (1405) 08L96-SZA-1A00-91 1 of 6

2. Fold down the third row seats. 5. Using a felt-tip pen, measure and mark two locations on the masking tape. LEFT REAR SIDE PANEL FRONT FELT-TIP PEN 19 mm 96 mm 215 mm 3. Attach masking tape along the outer edge of the third row seat back board as shown. 4. Using a felt-tip pen, measure and mark two locations on the masking tape. FRONT RIGHT REAR SIDE PANEL 6. While wearing eye protection, drill the two forward marked locations with a 3 mm drill bit, and then with a 5 mm drill bit. Drill through the hard board and the sheet metal. To prevent damage to the seat, wrap tape around the drill bit from the tip as shown. FELT-TIP PEN 96 mm 19 mm 215 mm 25 mm 3 mm 5 mm BIT 10 mm 10.5 mm BIT 7. Enlarge the holes with a 10.5 mm drill bit. To drill through the hard board only, wrap tape around the drill bit 10 mm from the tip as shown. 2 of 6 AII 51544 (1405) 2014 American Honda Motor Co., Inc. All Rights Reserved.

8. While wearing eye protection, drill the two rear marked locations with a 3 mm drill bit, and then with a 5 mm drill bit. Drill through the hard board and the sheet metal. To prevent damage to the seat, wrap tape around the drill bit from the tip as shown. 11. Using a felt-tip pen, measure and mark on the masking tape attached in step 10. FELT-TIP PEN FRONT SEAT BACK BOARD 98 mm 37 mm 3 mm 5 mm BIT 12. Using a felt-tip pen, measure and mark on the masking tape attached in step 10. 9. Remove the masking tape. 10. Fold down the second row seats. Attach two pieces of masking tape to the second row seat back board as shown. SEAT BACK BOARD FELT-TIP PEN 97 mm 44 mm 2014 American Honda Motor Co., Inc. All Rights Reserved. AII 51544 (1405) 3 of 6

13. While wearing eye protection, drill the marked locations with a 3 mm drill bit, and then with a 5 mm drill bit. Drill through the hard board and the sheet metal. To prevent damage to the seat, wrap tape around the drill bit from the tip as shown. 16. Assemble four self-tapping screws on the four anchors B. 4 ANCHORS B 4 SELF-TAPPING SCREWS 3 mm 5 mm BIT 14. Remove the masking tape. 15. Assemble two self-tapping screws on the two anchors A (Large). 17. Install the two anchors A (Large) on the third row seat back board into the holes made in step 7. 4 ANCHORS B (Large) (Large) ANCHOR A, ANCHOR B ANCHORS B 2 SELF-TAPPING SCREWS Position the anchors vertically. SEAT BACK BOARD 18. Install the four anchors B on the second and third row seat back boards into the holes made in steps 8 and 13. 4 of 6 AII 51544 (1405) 2014 American Honda Motor Co., Inc. All Rights Reserved.

Installing the Advanced Cargo Net Position 1 19. Fold down the third row seats. Position 2 21. Fold the advanced cargo net and secure it with two buttons. 2 BUTTONS 22. Attach five loops on the advanced cargo net to two anchors A (Large), two anchors B and the hook on the third row seat back board. (Large), 4 LOOPS HOOK LOOP (Large), 20. Attach six loops on the advanced cargo net to two anchors A (Large) and four anchors B on the second and third row seat back boards. 4 LOOPS 2 HOOKS 23. Attach two loops on the advanced cargo net to the two hooks. 2014 American Honda Motor Co., Inc. All Rights Reserved. AII 51544 (1405) 5 of 6

Position 3 24. Attach four snaps onto the advanced cargo net as shown. Position 4 27. Attach two snaps onto the advanced cargo net as shown. 4 SNAPS 2 SNAPS 25. Fold down the third row seats. (Large) 28. Attach four loops on the advanced cargo net to two hooks and two anchors B on the third row seat back board. 2 HOOKS 4 SNAPS 2 SNAPS 4 TIE-DOWN HOOKS 26. Attach the four snaps on the advanced cargo net to four tie-down hooks. Hook two loops on the advanced cargo net to the two anchors A (Large) on the third row seat back board. 2 TIE-DOWN HOOKS 29. Attach the two snaps on the advanced cargo net to two tie-down hooks. 6 of 6 AII 51544 (1405) 2014 American Honda Motor Co., Inc. All Rights Reserved.