Pumps & Accessories catalogue

PSC SYSTEMS COMPANY INC. Pumps & Accessories catalogue Phone: (800) 246-9689 Email: parts@pscclean.com Fax: (905) 738-9259 Website: www.pscclean.com

TABLE OF CONTENTS - pg. 1 CUSTOMER SERVICE DEPARTMENT EMAIL: parts@pscclean.com TRIGGER GUNS PG. 3-4 LANCES PG. 4 LANCE ASSEMBLIES PG. 5 NOZZLES PG. 5 HOSE ASSEMBLIES PG. 6-7 HOSE REELS PG. 7-8 CHEMICAL INJECTORS, APPLICATORS AND STRAINERS PG. 9 CONNECTORS AND SWIVELS PG. 10 BALL VALVES AND BALL VALVE ASSEMBLIES PG. 10-11 REGULATORS AND UNLOADERS PG. 11-12 AND SWITCHES PG. 12 GAUGES PG. 12 DRIVE COMPONENTS PG. 13 TEMPERATURE CONTROLLERS PG. 13 ACCUMULATORS/PULSATION DAMPENERS PG. 13 STRAINERS AND FILTERS PG. 14 LUBRICANTS PG. 14 MISCELLANEOUS ACCESSORIES PG. 14 GENERAL PLUNGER PUMPS PG. 15-16 CAT PLUNGER PUMPS PG. 17 20 CAT PISTON PUMPS PG. 20 22 PRATASSOLI PLUNGER PUMPS PG. 22 23 TECHNICAL DATA PG. 24 PSC s EQUIPMENT OVERVIEW PG. 25 THE INFORMATION CONTAINED HEREIN IS SUBJECT TO CHANGE WITHOUT NOTICE. COPYRIGHT 2012 PSC CLEANING SYSTEMS INC., ALL RIGHTS RESERVED PSC Pressure Systems Company Inc. 3300 Steeles Ave. West, Concord, Ontario, Canada L4K 2Y4 tel: 800-246-9689 / 905-761-1733 fax: 905-738-6168 www.pscclean.com email: info@pscclean.com

TRIGGER GUNS ST1500 TRIGGER GUN : 5000 PSI RATE: 12 GPM TEMPERATURE: 300 F WEIGHT: 20.5 OZ INLET - OUTLET: 3/8 FNPT - 1/4 FNPT - STANDARD: 202885 WEEP: 206276 REPAIR KIT - STANDARD: 202501 WEEP: 206317 ST2000 TRIGGER GUN : 5000 PSI RATE: 12 GPM TEMPERATURE: 300 F WEIGHT: 26 OZ INLET - OUTLET: 3/8 FNPT - 1/4 FNPT : 202472 / REPAIR KIT: 202501 ST2605 RELAX ACTION TRIGGER GUN : 5000 PSI RATE: 12 GPM TEMPERATURE: 300 F WEIGHT: 21 OZ INLET-OUTLET: 3/8 FNPT - 1/4 FNPT : 202861 / REPAIR KIT: 206312 ST2700 SS RELAX ACTION TRIGGER GUN : 5000 PSI RATE: 12 GPM TEMPERATURE: 300 F WEIGHT: 21 OZ INLET-OUTLET: 3/8 FNPT - 1/4 FNPT : 400740 / REPAIR KIT: 401566 ST2705 RELAX ACTION TRIGGER GUN : 7300 PSI RATE: 8 GPM TEMPERATURE: 300 F WEIGHT: 22 OZ INLET-OUTLET: 3/8 FNPT - 1/4 FNPT ST3100 FOAM SPRAY GUN : 900 PSI RATE: 26 GPM TEMPERATURE: 176 F WEIGHT: 42.5 OZ INLET-OUTLET: 1/2 FNPT 1/2 FNPT : 401616/ REPAIR KIT: 401617 : 206316 / REPAIR KIT: 206314 ST601 TRIGGER GUN : 4000 PSI RATE: 12 GPM TEMPERATURE: 300 F WEIGHT: 23 OZ INLET-OUTLET: 3/8 FNPT - 1/4 FNPT - STANDARD: 200803 WEEP: 200806 REPAIR KIT - STANDARD: 202501 WEEP: 206317 ST3002 TRIGGER GUN : 7250 PSI RATE: 26 GPM TEMPERATURE: 300 F WEIGHT: 42.5 OZ INLET-OUTLET: 1/2 FNPT 1/2 FNPT : 400800 / REPAIR KIT: 206311

TRIGGER GUNS G250V TRIGGER GUN : 4000 PSI RATE: 12 GPM : 350 PSI RATE: 14 GPM TEMPERATURE: 300 F WEIGHT: 25 OZ TEMPERATURE: 100 F WEIGHT: 28 OZ INLET - OUTLET: 3/8 FNPT - 1/4 FNPT INLET: 1/2 FNPT : 240155 / REPAIR KIT: 220304 : 401618 LANCES ST1200 TRIGGER GUN ST1200 TRIGGER GUN SINGLE LANCES DUAL LANCES 1/4 diameter zinc plated or stainless steel with solid or vented grip 4000 psi rated Part no. length material grip 202493 12 zinc plated steel solid 202622 18 zinc plated steel solid 400109 24 zinc plated steel solid 202494 36 zinc plated steel solid 202495 48 zinc plated steel solid 202496 60 zinc plated steel solid 400133 79 zinc plated steel solid SPECIALTY LANCES ST72 FOAM LANCE WITH AIR INJECTION 1/4 diameter zinc plated or stainless steel with solid or vented grip and hi/low valve 4000 psi Part no. length material grip 200794 38 zinc plated steel solid 401444 40 stainless steel vented SPECIALTY LANCES WATER BLASTING LANCES ST3002-L 38 (part no. 200601) ST3002-L 19 (part no. 200601) ½ mnpt x ¼ fnpt 10,000 psi rated Both used with ST3002 & ST3100 trigger gun With integral air ports and diffusers - max. 900 psi / 300 F Part no. length flow rate-gpm 401619 48 1.0 to 2.9 401620 48 3.0 to 3.9 401621 48 4.0 to 5.0 Part no. length material grip 200601 19 stainless steel side handle 400801 38 stainless steel side handle LANCE ACCESSORIES LANCE HANDLES 209102 FLEX WAND A C B industrial grade polyurethane flex section maximum pressure 2000 psi maximum temperature 200 f inlet & outlet 1/4 mnpt A lance handle for molded grip - part no. 401625 B lance handle for any ¼ lance - part no. 400138 C shoulder support for st2605/st2700/st2705 guns - part no. 401624 D shoulder support - part no. 401623 D

Lance assemblies SLG (SINGLE LANCE GUN) ASSEMBLIES DLG (DUAL LANCE GUN) ASSEMBLIES SLG ASSEMBLY WITH ST1500 TRIGGER GUN, 36 LANCE AND NOZZLE DLG ASSEMBLY WITH ST1500 TRIGGER GUN, 38 LANCE AND NOZZLES EZ-SLG ASSEMBLY WITH ST2605 TRIGGER GUN, 36 LANCE AND NOZZLE EZ-DLG ASSEMBLY WITH ST2605 TRIGGER GUN, 38 LANCE AND NOZZLES SLG-SS ASSEMBLY WITH ST2700 TRIGGER GUN, DLG-SS ASSEMBLY WITH ST2605 TRIGGER GUN, 36 LANCE AND NOZZLE 40 LANCE AND NOZZLES *SPECIFY NOZZLE SIZE WHEN ORDERING NOZZLES THREADED NOZZLES QUICK CONNECT NOZZLES ROTARY NOZZLES HARDENED STAINLESS STEEL CONSTRUCTION 0, 15, 25 OR 40 FAN PATTERN 1/8 OR 1/4 MNPT THREADS SEE PRICE LIST FOR PART NUMBERS 220370 DOUBLE NOZZLE HOLDER HARDENED STAINLESS STEEL CONSTRUCTION 0, 15, 25 OR 40 FAN PATTERN 1/4 QUICK CONNECT DESIGN SEE PRICE LIST FOR PART NUMBERS 220000 ADJUSTABLE NOZZLE HOLDER A B ST357 SERIES (A) MAX. 3000 PSI, 190 F - 1/4 FNPT ST457 SERIES (B) MAX. 5000 PSI, 212 F - 1/4 FNPT SEE PRICE LIST FOR PART NUMBERS MRI ADJUSTABLE NOZZLE MAXIMUM 2900 PSI / 10.5 GPM / 300 F INLET & OUTLETS (2) 1/4 FNPT NOZZLE STRAINERS MAXIMUM 3600 PSI / 8 GPM / 300 F INLET & OUTLET 1/4 FNPT PIPE CLEANING NOZZLES ADJUSTABLE FAN PATTERN FROM 0 TO 60 HIGH OR LOW SELECTION MAXIMUM 3000 PSI / 5.5 GPM / 140 F INLET SIZE 1/4 BSP-F MAXIMUM 5000 PSI / 8 GPM / 190 F 1/4 FNPT BUSHING 1/4 QC PLUG X 1/4 MNPT 401626 1/4 FNPT X 1/4 MNPT 401627 EFFECTIVE FOR CLEANING PIPES UP TO 6 IN. DIAMETER ORFICE SIZE THREAD SIZE ROTATING 202961 5.5 1/8 IN. F NO 201680 4.5 1/4 IN. F NO 202916 5.5 1/4 IN. F NO 202917 6.0 1/4 IN. F NO 202918 7.5 1/4 IN. F NO 206277 5.5 1/4 IN. F YES *SBH WET SANDBLASTING KIT FOR WET SANBLASTING USES DRY AND SIFTED QUARTZ OR SILICA SAND WITH 15FT SUCTION HOSE SPIGOT & QUICK CONNECT

HIGH WASH & CONNECTION HOSES HOSES & ASSEMBLIES DRAIN & PIPE CLEANING HOSES ST36 SLUDGE SUCTION HOSE 3000 PSI TO 10000 PSI RATED ASSEMBLIES AVAILABLE STANDARD, FOOD-GRADE OR STEAM RATED OR NON-MARKING UP TO 3000 PSI RATED ASSEMBLIES IDEAL FOR SMALL DIAMETER DRAIN AND PIPE CLEANING UP TO 4000 PSI CONNECTION 104 F TEMPERATURE RATING 11:1 RATIO (WATER) DUTY INNER DIAMETER LENGTH MAX. OPERATING FITTING SIZE (INCHES) MAX. TEMPERATURE 206117 PRESS. WASH 3/8 IN. 15 FT. 4000 PSI 3/8 M X 3/8 M -20 TO 250 F 200880 PRESS. WASH 3/8 IN. 30 FT. 4000 PSI 3/8 M X 3/8 M -20 TO 250 F 200881 PRESS. WASH 3/8 IN. 50 FT. 4000 PSI 3/8 M X 3/8 M -20 TO 250 F 206208 PRESS. WASH 3/8 IN. 75 FT. 4000 PSI 3/8 M X 3/8 M -20 TO 250 F 200882 PRESS. WASH 3/8 IN. 100 FT. 4000 PSI 3/8 M X 3/8 M -20 TO 250 F 202451 PRESS. WASH 3/8 IN. 200 FT. 4000 PSI 3/8 M X 3/8 M -20 TO 250 F 202698 PRESS. WASH 1/2 IN. 50 FT. 4000 PSI 3/8 M X 3/8 M -20 TO 250 F 200883 PRESS. WASH 1/2 IN. 75 FT. 4000 PSI 1/2 M X 1/2 M -20 TO 250 F 401126 PRESS. WASH 1/2 IN. 100 FT. 4000 PSI 1/2 M X 1/2 M -20 TO 250 F 202854 PRESS. WASH 1/2 IN. 50 FT. 4000 PSI 1/2 M X 1/2 M -20 TO 250 F 206289 STEAM 3/8 IN. 35 FT. 500 PSI 3/8 M X 1/2 M 300 F 206284 STEAM 1/2 IN. 50 FT. 500 PSI 3/8 M X 1/2 M 300 F NOTE: NON-MARKING HOSE COVER, ask for Yellow hose (c/w R&S & Guards) 207204 PRESS. WASH 3/8 in. 25 3000 psi 3/8 M X 3/8 M -20 TO 250 F 206286 PRESS. WASH 3/8 in. 30 3000 psi 3/8 M X 3/8 M -20 TO 250 F 206285 PRESS. WASH 3/8 in. 50 3000 psi 3/8 M X 3/8 M -20 TO 250 F 207129 PRESS. WASH 3/8 in. 60 3000 psi 3/8 M X 3/8 M -20 TO 250 F 206287 PRESS. WASH 3/8 in. 60 3000 psi 3/8 M X 3/8 M -20 TO 250 F NON-MARKING HOSE COVER, BLUE (Food Grade) 206624 PRESS. WASH 3/8 in. 50 4000 psi 3/8 M X 3/8 M -20 TO 250 F 206804 PRESS. WASH 3/8 in. 100 4000 psi 3/8 M X 3/8 M -20 TO 250 F SEWER HOSES 206717 PRESS. WASH 1/8 in. 50 3000 psi -20 TO 250 F 206718 PRESS. WASH 1/8 in. 100 3000 psi -20 TO 250 F HIGH CONNECTION HOSES DUTY 202520 206112 PRESS. WASH PRESS. 206110 WASH PRESS. 206113 WASH PRESS. 206119 WASH PRESS. 206152 WASH PRESS. WASH INNER DIAMETER LENGTH MAX. OPERATING FITTING SIZE (INCHES) MAX. TEMP 3/8 IN. 26 IN. 3000 PSI 3/8 M X 3/8 M 250 F 3/8 IN. 36 IN. 3000 PSI 3/8 M X 3/8 M 250 F 3/8 IN. 48 IN. 3000 PSI 3/8 M X 3/8 M 250 F 3/8 IN. 60 IN. 3000 PSI 3/8 M X 3/8 M 250 F 3/8 IN. 72 IN. 3000 PSI 3/8 M X 3/8 M 250 F 1/2 IN. 72 IN. 3000 PSI 1/2 M X 1/2 M 250 F

DRAIN CLEANING & PIPE CLEANING HOSES DUTY INNER DIAMETER LENGTH MAX. OPERATING FITTING SIZE (INCHES) 206146 PIPE CLEANING 1/8 IN. 50 FT. 3000 PSI 1/8 M X 1/8 M 206258 PIPE CLEANING 1/8 IN. 100 FT. 3000 PSI 1/8 M X 1/8 M 401200 PIPE CLEANING 1/4 IN. 50 FT. 2750 PSI 1/4 M X 1/4 M 401197 PIPE CLEANING 1/4 IN. 100 FT. 2750 PSI 1/4 M X 1/4 M DCK1 PIPE CLEANING 1/8 IN. 50 FT. 3000 PSI 1/4 F DCK2 PIPE CLEANING 1/8 IN. 100 FT. 3000 PSI 1/4 F DCK3 PIPE CLEANING 1/4 IN. 50 FT. 2750 PSI 1/4 F DCK4 PIPE CLEANING 1/4 IN. 100 FT. 2750 PSI 1/4 F SLUDGE SUCTION HOSE SPECIFY HIGH NOZZLE SIZE WHEN ORDERING DUTY INNER DIAMETER LENGTH MAX. OPERATING INLET FITTING MAX. TEMPERATURE 400136 SLUDGE REMOVAL 1-1/2 IN. 25 FT. 4000 PSI 1/4 IN. M Q.C. 200 F IN ADDITION TO THE HOSES SHOWN ABOVE, A FULL RANGE OF HIGH AND LOW HOSES & LENGTHES ARE AVAILABLE FOR VIRTUALLY ANY APPLICATION. CONTACT OUR CUSTOMER SERVICE DEPARTMENT FOR INFORMATION AND PRICING.

MANUAL REWIND HOSE REELS HOSE REELS MANUAL REWIND 360 PIVOTING HOSE REELS HOSE CAPACITY MODEL 3/8 IN. I.D. HOSE 1/2 IN I.D. HOS HRA-16 200 175 206288 100 60 * SHOWN WITH 200613 200 175 OPTIONAL HOSE AND QUICK CONNECT EEL CAPACITIES MAY VARY NDING ON HOSE BRAND AND TYPE * SHOWN WITH OPTIONAL HOSE AND QUICK CONNECT HRA16 / 403115-16 IN. DIAMETER DRUM DURABLE POWDER COAT PAINT FINISH CAM LEVER BRAKE WITH REEL LOCK UP TO 5000 PSI / 300 F INCLUDES UNIVERSAL MOUNTING BRACKET 206288-13 IN. DIAMETER DRUM 200613-16 IN. DIAMETER DRUM DURABLE POWDER COAT PAINT FINISH CAM LEVER BRAKE WITH PIVOT & REEL LOCK UP TO 5000 PSI / 300 F OPTIONAL 401219 WALL MOUNTING BRACKET AVAILABLE T SERIES SPRING REWIND HOSE REELS MP SERIES SPRING REWIND HOSE REELS - STAINLESS T SERIES - STANDARD * SHOWN WITH OPTIONAL HOSE AND HOSE STOP MAXIMUM HOSE MODEL CAPACITY 401568 3000 50 X 3/8 ID 206419 3000 75 X 3/8 ID 401521 4000 50 X 3/8 ID 206542 4000 75 X 3/8 ID SUPREME-DUTY REEL WITH ADJUSTABLE GUIDE ARMS, SIX- ROLLER NON-SNAG HOSE GUIDE AND 1 IN. SELF LUBRICATING BEARING FULL SWIVEL JIONT AND 8 POSITION LOCKING RATCHET SOLID 1 IN. STEEL CENTRE SUPPORT SHAFT DURABLE POWDER COAT PAINT FINISH MODEL MP SERIES STAINLESS STEEL MAXIMUM HOSE CAPACITY 206543 3000 50 X 3/8 ID 206544 3000 50 X 1/2 ID SUPREME-DUTY REEL WITH ADJUSTABLE GUIDE ARMS, SIX- ROLLER NON-SNAG HOSE GUIDE AND 1 IN. SELF LUBRICATING BEARING FULL SWIVEL JOINT AND 8 POSITION LOCKING RATCHET SOLID 1 IN. STEEL CENTRE SUPPORT SHAFT 316 STAINLESS STEEL SWIVEL AND AXEL. 304 STAINLESS STEEL DRUM AND BASE WITH ELECTROLYTIC POLSH PROCESS IN ADDITION TO THE MODELS SHOWN ABOVE, A FULL RANGE OF HIGH AND LOW HOSE REELS IS AVAILABLE FOR VIRTUALLY ANY APPLICATION. CONTACT OUR CUSTOMER SERVICE DEPARTMENT FOR INFORMATION AND PRICING.

CHEMICAL INJECTORS, APPLICATORS & STRAINERS ADJUSTABLE CHEMICAL & ACID INJECTORS STAINLESS STEEL CHEMICAL INJECTORS ADJUSTABLE UPSTREAM CHEMICAL INJECTORS MAXIMUM 4500 PSI / 195 F ADJUSTABLE CHEMICAL DRAW UP TO 20% BRASS CONSTRUCTION STANDARD INJECTOR WITH BUNA-N O- RING AND STAINLESS STEEL BALL ACID INJECTOR WITH TEFLON O-RING AND CERAMIC BALL INLET / OUTLET 3/8 IN. NPTM HOSE BARB 1/4 IN. ADJUSTABLE CHEMICAL INJECTOR ORFICE CS1 / CS1-3 REMOTE CHEMICAL STATIONS GPM 209047 1.5 MM 1.0 TO 2.0 GPM 240021 1.8 MM 2.0 TO 3.0 GPM 202087 2.1 MM 3.0 TO 5.0 GPM 209050 2.3 MM 5.0 TO 8.0 GPM REPAIR KIT ADJUSTABLE ACID INJECTOR ORFICE GPM 209129 1.5 MM 1.0 TO 2.0 GPM 240024 1.8 MM 2.0 TO 3.0 GPM 240022 2.1 MM 3.0 TO 5.0 GPM 240023 2.3 MM 5.0 TO 8.0 GPM REPAIR KIT MAXIMUM 5100 PSI / 195 F ADJUSTABLE CHEMICAL DRAW STAINLESS STEEL CONSTRUCTION WITH TEFLON O-RING AND STAINLESS STEEL BALL INLET / OUTLET 3/8 IN. BSPM HOSE BARB 1/4 IN. STAINLESS STEEL INJECTOR ORFICE CHEMICAL STRAINERS A B C (A) 401629 METERING VALVE FOR ST261 UNLOADER (B) 209017/209018 CHEMICAL STRAINER (209018 WITH CHECK VALVE) 1/4 IN. AND 3/8 IN. HOSE BARB (C) 401628 CHEMICAL STRAINER 1/4 IN. HOSE BARB CS2 CHEMICAL APPLICATOR GPM 240033 2.1 MM 2.6 TO 4.0 GPM 240050 2.3 MM 4.0 TO 5.3 GPM ADJUSTABLE CHEMICAL DRAW BRASS CONSTRUCTION SEE PRICE LIST FOR PART NUMBERS AND RATES IN-LINE CHEMICAL INJECTOR WATER PRESS. 202B 203B 206B PSI 10.25-2.0.50-3.5 3.6-11 20.30-2.3.55-4.4 4.2-13 40.37-2.9.70-5.4 5.3-17 60.43-3.4.80-6.4 6.2-19 100.54-4.2 1.0-8.0 7.7-24 200.73-5.7 1.4-11 11-33 400 1.0-7.9 1.9-15 15-46 500 1.2-8.9 2.1-17 17-51 *700 1.4-11 2.5-20 20-60 *1000 1.6-13 3.0-23 23-70 *1500 2.0-16 3.5-28 28-87 *2000 2.2-18 4.7-37 33-100 *3000 2.7-20 5.0-45 40-100 SPECIFY S.S. KNOB FOR EXCEEDING 750 PSI (I.E. 202BS) MAXIMUM INJECTION OUNCES PER MINUTE FLUID VISC. 202B 203B 206B CPS 1 8 16 42 75 4 8 18 220 2 4 8 500 1 2 4 1000 0.5 1 1 PIPE SIZE NPT 3/8 IN. 3/8 IN. 1/2 IN. ADJUSTABLE FOAM APPLICATORS INSTANTANEOUS CHANGE FROM CHEMICAL TO RINSE HIGH BRASS OR STAINLESS STEEL INJECTOR ALLOWS FOR ADJUSTABLE OR FIXED CHEMICAL DRAW 0-2000 PSI AND 0-3000 PSI MODELS AVAILABLE FOR USE WITH CLS/CLS-3 CLEANING STATION ASSEMBLY SPECIFY RATE WHEN ORDERING LOW APPLICATOR ALLOWS FOR ADJUSTABLE OR FIXED CHEMICAL APPLICATION WITHSTANDS MOST ACIDIC AND ALKALI CHEMICALS 24 IN. SPRAY WAND WITH 50 FT. X 1/2 IN. HOSE INCLUDES MOUNTING BRACKET WITH U BOLTS (A) 240174 FOAMER LANCE WITH 1.5 MM INJECTOR (B) 240175 FOAMER LANCE WITH 1.5 MM INJECTOR AND 1 QUART TANK A B

CONNECTORS & SWIVELS QUICK CONNECT PLUGS AND SOCKETS ST40 SCREW COUPLINGS ST41 SCREW NIPPLES A (A) ZINC PLATED PLUGS NOTE: STAINLESS STEEL AVAILABLE UPON REQUEST (B) BRASS SOCKETS WITH BUNA-N O- 0RING Q.C. SOCKETS THREAD SIZE 209031 1/4 MNPT 209032 1/4 FNPT 209033 3/8 MNPT 209034 3/8 FNPT Q.C. PLUGS THREAD SIZE 209023 1/4 FNPT 209024 1/4 MNPT 209025 3/8 FNPT 209026 3/8 MNPT B USED WITH ST41 SCREW NIPPLES MAXIMUM 5800 PSI OPERATING MAXIMUM 300 F TEMPERATURE RATING THREAD SIZE 201597 1/4 MNPT 202194 1/4 FNPT 200785 3/8 MNPT 200784 3/8 FNPT ST44 SWIVEL COUPLINGS USED WITH ST40 SCREW COUPLINGS MAXIMUM 5800 PSI OPERATING MAXIMUM 300 F TEMPERATURE RATING THREAD SIZE 200787 1/4 FNPT 200789 1/4 MNPT 200811 3/8 FNPT 20788 3/8 MNPT HIGH SWIVELS O-RINGS FOR SOCKETS 209079 1/4 209089 3/8 MAXIMUM 5.2 GAL/MIN RATE MAXIMUM 5800 PSI OPERATING MAXIMUM 300 F TEMPERATURE RATING THREAD SIZE 206537 1/4 MNPT 206538 3/8 FNPT MAXIMUM 5.2 GAL/MIN RATE MAXIMUM OPERATING : 209085-3000 PSI 209121-5000 PSI MAXIMUM 300 F TEMPERATURE RATING THREAD SIZE 209085 3/8 M X 3/8 F 209121 3/8 M X 3/8 F BALL VALVES / BALL VALVE ASSEMBLIES 2 WAY BALL VALVES BRASS, CARBON STEEL OR STAINLESS STEEL CONSTRUCTION UP TP 6000 PSI RATED HIGHER VALVES AVAILABLE UPON REQUEST CLS / CLS-3 CLEANING STATION ASSEMBLY HIGH RATED MATERIAL THREAD SIZE-IN. MAX. PRESS. MAX. TEMP. LOCKABLE BODY BALL 200743 CARBON STEEL STAINLESS 1/4 F X 1/4 F 2000 PSI 110 F NO 400246 STAINLESS STAINLESS 3/8 F X 3/8 F 2000 PSI 180 F YES 220009 STAINLESS STAINLESS 3/8 F X 3/8 F 6000 PSI 250 F NO 200742 CARBON STEEL STAINLESS 1/2 F X 1/2 F 2000 PSI 110 F NO 400247 STAINLESS STAINLESS 1/2 F X 1/2 F 2000 PSI 180 F YES 206535 STAINLESS STAINLESS 1/2 F X 1/2 F 6000 PSI 250 F NO CLS STAINLESS STAINLESS 3/8 F X 3/8 F 2000 PSI 250 F NO CLS-3 STAINLESS STAINLESS 1/2 F X 1/2 F 6000 PSI 250 F NO

BALL VALVES / BALL VALVE ASSEMBLIES LOW RATED MATERIAL THREAD SIZE-IN. MAX. PRESS. MAX. TEMP. LOCKABLE BODY BALL 201465 BRASS NICKEL PLATED 1/4 F X 1/4 F 250 PSI 180 F NO 400399 BRASS NICKEL PLATED 3/4 F X 3/4 F 150 PSI 250 F NO 400915 BRASS STAINLESS 3/4 F X 3/4 F 600 PSI 260 F YES DBV2103-F BRASS NICKEL PLATED 1 F X 1 F 150 PSI 250 F NO 202456 BRASS STAINLESS 1 F X 1 F 600 PSI 260 F YES DBV2103-J BRASS NICKEL PLATED 1-1/4 F X 1-1/4 F 150 PSI 250 F NO DBV2103-H BRASS NICKEL PLATED 1-1/2 F X 1-1/2 F 150 PSI 250 F NO REGULATORS AND UNLOADERS TRAPPED UNLOADER VALVES * REMOVE CHECK VALVE FOR USE AS A REGULATOR * A B C D E F G (ITEM) SPRING COLOUR MAXIMUM RATED MAXIMUM INLET OUTLET BY-PASS 220323 (A) BLUE 7.8 GPM 3600 PSI 4000 PSI 3/8 IN. NPTF 3/8 IN. NPTF 3/8 IN. NPTF 195 F 220756(A) WHITE 7.8 GPM 1450 PSI 1750 PSI (2) 3/8 IN. NPTF 3/8 IN. NPTF (2) 3/8 IN. NPTF 195 F 240158 (B) GREEN 21.0 GPM 4050 PSI 4350 PSI (2) 1/2 IN. NPTF 1/2 IN. NPTF (2) 1/2 IN. NPTF 200 F 220721 (B) WHITE 21.0 GPM 2175 PSI 2450 PSI (2) 1/2 IN. NPTF 1/2 IN. NPTF (2) 1/2 IN. NPTF 200 F 220296 (C) BLACK 21.0 GPM 5800 PSI 6500 PSI (2) 1/2 IN. NPTF 1/2 IN. NPTF (2) 1/2 IN. NPTF 200 F MAXIMUM TEMP. 220031(D) BLUE 21.0 GPM 3000 PSI 3000 PSI 3/8 IN. BSPF 1/4 IN. BSPF & 3/8 IN. (2) 3/8 IN. BSPF 200 F (ITEM) INJECTOR ORFICE-MM MAXIMUM RATED MAXIMUM INLET BSPM OUTLET BY-PASS MAXIMUM TEMP. 200799 (F) 1.8 8.0 GPM 3600 PSI 3600 PSI 3/8 IN. NPTF 3/8 IN. NPTF 3/8 IN. NPTF 176 F 200800 (F) 2.1 8.0 GPM 3600 PSI 3600 PSI 3/8 IN. NPTF 3/8 IN. NPTF 3/8 IN. NPTF 176 F 200801 (F) 2.4 8.0 GPM 3600 PSI 3600 PSI 3/8 IN. NPTF 3/8 IN. NPTF 3/8 IN. NPTF 176 F 200802 (G) - 8.0 GPM 3600 PSI 3600 PSI 3/8 IN. NPTF 3/8 IN. NPTF 3/8 IN. NPTF 176 F 202661 (F) - 8.0 GPM 3600 PSI 3600 PSI 3/8 IN. NPTF 3/8 IN. NPTF 3/8 IN. NPTF 176 F 202662 (G) 2.1 8.0 GPM 3600 PSI 3600 PSI 3/8 IN. NPTF 3/8 IN. NPTF 3/8 IN. NPTF 176 F REGULATOR AND UNLOADER VALVE REPAIR KITS REPAIR KIT NO. (ITEM) REPAIR KIT NO. REPAIR KIT NO. 401383 200799 (F) 206561 240197 240203 401383 200800 (F) 206561 240198 240203 220325 200801 (F) 206561 240199 240203 220325 200802 (G) 206562 240200 240204 206310 202661 (F) 206562 240095 401221 240115 202662 (G) 206562 209016 209095 201357/220096 240196 240203 - -

REGULATORS AND UNLOADERS SENSITIVE UNLOADER VALVES REGULATING VALVE BALANCED RELIEF VALVE SAFETY RELIEF VALVE MAXIMUM 3000 PSI / INLET 3/8 IN. BSPF OUTLET 3/8 IN. BSPM BY-PASS 3/4 IN. BSPM/F RANGE 240196 2.1 TO 3.0 GPM 240197 3.0 TO 4.2 GPM 240198 4.2 TO 6.6 GPM 240199 6.6 TO 10.8 GPM 240200 2.5 TO 13.2 GPM 240095 MAXIMUM 870 PSI / MAXIMUM 53 GPM INLET 3/4 IN. BSPF OUTLET 1/2 IN. BSPF BY-PASS 1 IN. BSPF 240096 RATED 3200 PSI/MAX. 3600 PSI MAXIMUM 6.3 GPM MAXIMUM TEMP. 195 F INLET (2) 3/8 IN. BSPF BY-PASS 3/8 IN. BSPF PN:220022 REDUCTION VALVE REDUCES INLET PRSSURE FROM MAX. 400 PSI TO 15-75 PSI MAXIMUM 10 GPM / INLET & OUTLET 3/4 IN. FGHT BY-PASS 3/4 IN. BSPM/F 209016 FOR USE ON SYSTEMS WITH UP TO 3000 PSI WORKING REQUIRES ADJUSTMENT TO 300 PSI ABOVE WORKING BRASS BODY WITH STAINLESS STEEL PISTON AND SPRING 1/2 IN. NPTM CONNECTION WITH SET SCREW AND 3/8 IN. HOSE BARB AND SWITCHES 200781 SWITCH 240036 SWITCH 202188 SWITCH GRAVITY ACTUATED MAXIMUM 3600 PSI / 8 GPM / 176 F MAXIMUM 400 VOLTS / 3.0 AMPS (100 WATTS) INLET / OUTLET 3/8 IN. FNPT X 3/8 IN. FNPT AL680 SWITCH SPRING ACTUATED WITH PILOT FEATURE MAXIMUM 4000 PSI / 165 F 0.75 GPM TO 6 GPM RATE - +6 GPM REQUIRES BY-PASS MAXIMUM 250 VOLTS / 3.0 AMPS INLET / OUTLET 3/8 IN. FNPT X 3/8 IN. FNPT ALL STAINLESS STEEL VERSION 400670 200893 SWITCH SPRING ACTUATED MAXIMUM 3600 PSI / 8 GPM / 176 F MAXIMUM 400 VOLTS / 3.0 AMPS (100 WATTS) INLET / OUTLET 3/8 IN. FNPT X 3/8 IN. MNPT GAUGES GLYCERIN FILLED GAUGES MAXIMUM 3650 PSI SWITCH 435 PSI MAXIMUM TEMPERATURE 200 F VOLTAGE 12 250 VOLT MAXIMUM AMPERAGE 15 AMPS 240094 THROTTLE CONTROL THROTTLE CONTROL FOR GASOLINE ENGINES RATED 725 PSI MAXIMUM 3000 PSI 3/8 IN. NPTM INLET ADJUSTABLE RANGE: DECREASING MIN..5 PSI MAX. 14.5 PSI / INCREASING MIN..6 PSI AMX. 15 PSI ELECTRICAL CONNECTION 1/2 IN. NPS CONDUIT CONNECTION TO SCREW TERMINALS ON SWITCH CONNECTION 1/4 IN. NPTF 24 VAC TO 250 VAC STAINLESS STEEL CASE WITH BRASS INTERNALS AND 2 IN. DIAMETER ACRYLIC WINDOW ACCURACY 1.5% OF SPAN 1/4 IN. NPTM BOTTOM MOUNT RANGE 220255 0 200 PSI 201487 0 2000 PSI 201488 0 3000 PSI 220039 0 4000 PSI 201489 0 5000 PSI

DRIVE COMPONENTS HIGHER RANGE GAUGES AVAILABLE PUMP PULLEYS GEAR REDUCERS CLUTCH DRIVES A PULLEYS - 2 GROOVE CAST ALUMINUM 24 MM BORE 201441 100 MM 3.9 PITCH 201442 140 MM 5.5 PITCH 201443 160 MM 6.3 PITCH PSC HAS A FULL LINE OF COMPONENTS AVAILABLE FOR VIRTUALLY ANY DRIVE-SYSTEM CONFIGURATION. CONTACT OUR CUSTOMER SERVICE DEPARTMENT FOR PRICING AND ASSISTANCE IN DETERMINING THE IDEAL COMPONENT PART(S) FOR YOUR REQUIREMENTS. TEMPERATURE CONTROLLERS 240179 -THROUGH THERMOSTAT PROBE-STYLE THERMOSTAT 403060 PROBE-STYLE THERMOSTAT (WELL 403059) MAXIMUM 3000 PSI / 12 GPM 50 F TO 300 F RANGE FACTORY PRESET FOR MAXIMUM 200 F INLET & OUTLET 1/2 IN. NPTF SRA SURGE RELIEF ASSEMBLY 86 F TO 194 F RANGE 240042 86 F TO 302 F RANGE 240046 MAXIMUM 4000 PSI / 380 VOLT / 4 AMPS ACCUMULATORS/PULSATION DAMPENERS PDH PULSATION DAMPENER 100 F TO 240 F RANGE 5 F TO 45 F DIFFERENTIAL 4 IN. PROBE WELL WITH 1/2 IN. NPTM FITTING CONVERTIBLE FROM HORIZONTAL TO VERTICAL FOR USE IN 24, 120 & 240 VOLT CIRCUITS 6028 PULSATION DAMPENER SHOULD BE INSTALLED ON THE WATER SUPPLY LINE WHEN THE SUPPLY LINE HAS A BACK PREVENTER, REDUCING OR CHECK VALVE PRESENT MAXIMUM 150 PSI / 200 F 40 PSI AIR PRECHARGE RECHARGEABLE FACTORY SET SAFETY RELIEF VALVE INLET/OUTLET 3/4 IN. M X 3/4 IN. F GARDEN HOSE FITTINGS RATED MAXIMUM 10 GPM / 3000 PSI / 175 F 21 CU. IN. CAPACITY 580 PSI DRY NITROGEN PRECHARGE - RECHARGEABLE CARBON STEEL CONSTRUCTION PORT SIZE 1/2 IN. NPTF RATED MAXIMUM 15 GPM / 3000 PSI / 180 F 10 CU. IN. CAPACITY 450 PSI DRY NITROGEN PRECHARGE - SEALED POLY-STEEL CONSTRUCTION PORT SIZE 1/2 IN. NPTM CONTACT OUR CUSTOMER SERVICE DEPARTMENT FOR INFORMATION AND PRICING ON ACCUMULATORS AND PULSATION DAMPENERS RANGING UP TO 120 CU. IN. CAPACITY

STRAINERS & FILTERS 201470 GARDEN HOSE FILTER WASHER SUCTION FILTER WFI INLINE FILTER STAINLESS STEEL SCREEN 206540 WITH 3/4 IN. & 1 IN. HOSE BARB 206541 WITH CHECK VALVE AND 3/4 IN. & 1 IN. HOSE BARB 20 MESH INTAKE SCREEN ALUMINUM BODY WITH 50 MESH STAINLESS STEEL SCREEN MAXIMUM 145 PSI / 5.8 GPM / 175 F INLET X OUTLET 1/2 IN. BSP-F X 1/2 IN. BSP-M PN:400879 7100 SERIES INLINE FILTERS BOWL-TYPE LUBRICANTS cat crankcase oil is a special blend, multi-viscosity petroleum based hydraulic lubricant for high pressure hydraulic systems. non-detergent for greater wear and protection at high rpm and pressure. anti-wear, high pressure and oxidizer inhibitor additives for maximum protection and wear. runs significantly cooler than typical lubricants, enhancing the longevity of components. NYLON BODY WITH 304 SS MESH SCREEN INSIDE OUT DIRECTION ALLOWS SEDIMENT COLLECTION INSIDE OF SCREEN MAXIMUM 150 PSI / 150 F MAXIMUM SUCTION/ PORT SIZE DIMENSIONS INCHES 7104 6 GPM / 10 GPM 1/2 IN. 3.6X2.95X5.35 7105 15 GPM / 20 GPM 3/4 IN. 3.6X2.95X5.35 7106 20 GPM / 25 GPM 1 IN. 5.0X4.1X6.35 7108 60 GPM / 75 GPM 1-1/2 IN. 5.13X4.1X8.13 SIZE 6101 21 U.S. OZ. 6100 12 X 21 U.S. OZ. 6105-1 2.5 U.S. GAL. 6105 2 X 2.5 U.S. GAL. JETTER VALVE MISCELLANEOUS ACCESSORIES 400280 ANALOG HOUR METER 240173 TANK CLEANER FOR USE IN SEWER CLEANING APPLICATIONS REPLACES VALVE CAP APPLICATION 240176 USE WITH TT SERIES PUMPS 240177 USE WITH EZ SERIES PUMPS 240178 USE WITH 47 SERIES PUMPS HIGH QUALITY DESIGN WITH ACCURATE READOUT 24 VAC 2-3/4 IN. FACE 6 COUNT INDICATION INCLUDING 1/10 HOUR AIR-DRIVEN 4.0 TO 10.5 GPM MAXIMUM 2000 PSI ROTATING HEAD WITH 4 NOZZLES FOR SMALL OPENINGS REQUIRES 400279 GASKET AT PSC WE STOCK A WIDE RANGE OF ACCESSORIES FOR USE WITH VIRTUALLY ANY BRAND OF WASHER. CONTACT OUR CUSTOMER SERVICE DEPARTMENT IF THE ACCESSORY YOU NEED IS NOT SHOWN IN THIS CATALOGUE.

HIGH PLUNGER PUMPS-GENERAL (Contact us if your pump is not listed here) T9051EBF or T9051BA 2.11 GPM MAXIMUM 1500 PSI INLET 1750 BORE 0.591 STROKE 0.370 11.2 OZ. 1/4 NPTF TT9061EBF or TT9061BA 2.11 GPM MAXIMUM 1500 PSI INLET 3400 BORE 0.591 STROKE 0.197 11.2 OZ. 1/4 NPTF TT9071EBF or TT9071BA 2.8 GPM MAXIMUM 1500 PSI INLET 3400 BORE 0.591 STROKE 0.260 11.2 OZ. 1/4 NPTF T9951 or T9951B 3.5 GPM MAXIMUM 1500 PSI INLET 1750 STROKE 0.335 15.2 OZ. TT2035GBF 3.5 GPM MAXIMUM 2000 PSI INLET 3400 BORE 0.591 STROKE 0.315 11.2 OZ. 1/4 NPTF T991 3.5 GPM MAXIMUM 1500 PSI INLET 1450 STROKE 0.394 15.2 OZ. EZ2542E or W959BH 4.2 GPM MAXIMUM 2500 PSI INLET 1750 BORE 0.708 STROKE 0.512 14.0 OZ. EZ3040G or WW961BC 4.0 GPM MAXIMUM 3000 PSI INLET 3400 BORE 0.591 STROKE 0.374 14.0 OZ. TS1011 4 GPM MAXIMUM 2000 PSI INLET 1450 STROKE 0.472 33.8 OZ.

TS2011 4 GPM MAXIMUM 3500 PSI INLET 1450 STROKE 0.472 40.6 OZ. T1321 ot T1321B 5.5 GPM MAXIMUM 2100 PSI INLET 1150 BORE 0.866 STROKE 0.630 40.6 OZ. T9211 ot T9211B 4 GPM MAXIMUM 3000 PSI INLET 1750 STROKE 0.394 40.6 OZ. TS2021 or TS2021BN 5.6 GPM MAXIMUM 3500 PSI INLET 1450 BORE 0.866 STROKE 0.630 40.6 OZ. TS1041 or TS1041B 8 GPM MAXIMUM 1600 PSI INLET 1450 STROKE 0.630 50.7 OZ. TS1531 7.92 GPM MAXIMUM 2175 PSI INLET 1450 STROKE 0.866 50.7 OZ. T1631 10 GPM MAXIMUM 2500 PSI INLET 1080 BORE 0.866 STROKE 0.630 54 OZ. INLET PORTS (4) DISCHARGE PORTS (4) T2031 9 GPM MAXIMUM 3000 PSI INLET 1140 STROKE 0.630 54 OZ. INLET PORTS (4) DISCHARGE PORTS (4) T5050 5 GPM MAXIMUM 5000 PSI INLET 1845 BORE 0.630 STROKE 0.748 40.6 OZ.

HIGH PLUNGER PUMPS CAT (Contact us if your pump is not listed here) 2SFX29ELS 2.85 GPM MAXIMUM 1500 PSI INLET -2 TO 75 PSI 1725 BORE 0.708 STROKE 0.335 11.83 OZ. INLET PORT (1) SHAFT (HOLLOW) 5/8 WEIGHT (PUMP ONLY) 10.6 LBS. 2SFX22ES 2.2 GPM MAXIMUM 2500 PSI INLET -2 TO 75 PSI 3450 BORE 0.708 STROKE 0.132 11.83 OZ. INLET PORT (1) SHAFT (HOLLOW) 5/8 WEIGHT (PUMP ONLY) 10.6 LBS. 2SFX30GS 3 GPM MAXIMUM 2000 PSI INLET -2 TO 75 PSI 3450 BORE 0.708 STROKE 0.177 11.83 OZ. INLET PORT (1) SHAFT (HOLLOW) 3/4 WEIGHT (PUMP ONLY) 10.6 LBS. 4SF40ELS 4 GPM 3500 PSI INLET FLOODED TO 60 PSI 1725 STROKE 0.382 23.66 OZ. INLET PORT (1) BY-PASS PORT (1) SHAFT (HOLLOW) 1 1/8 4SF45ELS 4.5 GPM 3000 PSI INLET FLOODED TO 60 PSI 1725 STROKE 0.437 23.66 OZ. INLET PORT (1) BY-PASS PORT (1) 4SF40GS1 4 GPM 3500 PSI INLET FLOODED TO 60 PSI 3200 STROKE 0.224 23.66 OZ. INLET PORT (1) BY-PASS PORT (1) SHAFT (HOLLOW) 1 3CP1120 4.2 GPM 100 TO 2200 PSI INLET FLOODED TO 60 PSI 1725 BORE 0.709 STROKE 0.500 11.8 OZ. 5CP5120 5 GPM 100 TO 3000 PSI INLET FLOODED TO 60 PSI 1415 BORE 0.709 STROKE 0.709 17 OZ. 5CP6120 6 GPM 100 TO 1600 PSI INLET FLOODED TO 60 PSI 1450 STROKE 0.709 17 OZ.

HIGH PLUNGER PUMPS-CAT (Contact us if your pump is not listed here) 7CP6170 11 GPM 100 TO 2000 PSI INLET 1450 BORE 0.866 STROKE 1.024 38 OZ. 140 F 310 4 GPM 100 TO 2200 PSI INLET -5 TO +60 PSI 950 STROKE 0.709 18 OZ. 550 5 GPM 100 TO 3000 PSI INLET -5 TO +60 PSI 1415 BORE 0.630 STROKE 0.945 25OZ. 650 7 GPM 100 TO 3000 PSI INLET -5 TO +60 PSI 1000 STROKE 1.181 42 OZ. 660 10 GPM* 100 TO 3000 PSI* INLET +10 TO +60 PSI 1429 STROKE 1.181 42 OZ. SHAFT DIAMETER (D-END) 1.181 WEIGHT 44 LBS. 1050 10 GPM 100 TO 2200 PSI INLET -5 TO +60 PSI 958 BORE 0.945 STROKE 1.181 42 OZ. 2530 21 GPM 100 TO 1200 PSI INLET 914 BORE 1.260 STROKE 1.516 84 OZ. 1 1/4 NPTF 3507 9 GPM 100 TO 5000 PSI INLET 800 STROKE 1.890 134.4 OZ. 1 3517 14 GPM 100 TO 3000 PSI INLET 800 BORE 0.984 STROKE 1.890 134.4 OZ. 1

HIGH PLUNGER PUMPS CAT (Contact us if your pump is not listed here) 3520 23 GPM 100 TO 2000 PSI INLET 800 BORE 1.260 STROKE 1.890 134.4 OZ. 1 3535 36 GPM 100 TO 1200 PSI INLET 800 BORE 1.575 STROKE 1.890 134.4 OZ. 1 3545 45 GPM 100 TO 1000 PSI INLET 800 BORE 1.772 STROKE 1.890 134.4 OZ. 140 F 1 3801 9 GPM 100 TO 1200 PSI INLET 800 STROKE 1.890 134.4 OZ. 1 3811 14 GPM 100 TO 3000 PSI INLET 800 BORE 0.984 STROKE 1.890 134.4 OZ. 1 3821 23 GPM 100 TO 2000 PSI INLET 800 BORE 1.260 STROKE 1.890 134.4 OZ. 1 3831 36 GPM 100 TO 1200 PSI INLET 800 BORE 1.575 STROKE 1.890 134.4 OZ. 1 6811 15 GPM 100 TO 5000 PSI INLET FLOODED TO 50 PSI 600 BORE 0.984 STROKE 2.579 320 OZ. 120 F 1 6821 25 GPM 100 TO 3000 PSI INLET FLOODED TO 50 PSI 615 BORE 1.260 STROKE 2.579 320 OZ. 120 F 1

HIGH PLUNGER PUMPS CAT (Contact us if your pump is not listed here) 6831 40 GPM 100 TO 2300 PSI INLET FLOODED TO 50 PSI 625 BORE 1.575 STROKE 2.579 320 OZ. 140 F 1 6841 48 GPM 100 TO 2000 PSI INLET FLOODED TO 50 PSI 615 BORE 1.771 STROKE 2.579 320 OZ. 120 F 2 1 1/4 NPTF 6861 60 GPM 100 TO 1200 PSI INLET FLOODED TO 60 PSI 520 BORE 2.165 STROKE 2.579 320 OZ. 120 F 2 1 1/4 NPTF 150R060-CARBON STEEL 151R060-STAINLESS STEEL 152R060-DUPLEX SS SPECIFICATIONS STANDARD ALTERNATE API 100 GPM 115 GPM 86 GPM 2700 PSI 2300 PSI 2700 PSI 310 COMMON SPECIFICATIONS 360 270 INLET FLOODED TO 50 PSI MINIMUM 75 BORE 2.36 STROKE 5.91 120 F 22.4 GAL. 6.0 NPTF 4.0 NPTF SHAFT DIAMETER (D-END) 4.724 SHAFT LENGTH 8.081 HIGH PISTON PUMPS CAT 280 3 GPM 100 TO 1000PSI INLET 1330 STROKE 0.394 10 OZ. INJECTION PORT (1) 1/4 NPTF DISCHARGE PORTS (1) 290 3.5 GPM 100 TO 1200 PSI INLET 1200 STROKE 0.472 10 OZ. INJECTION PORT (1) 1/4 NPTF DISCHARGE PORTS (1) 333 4 GPM 100 TO 1200 PSI INLET 1070 BORE 0.709 STROKE 0.768 21 OZ. INJECTION PORT (1) 1/4 NPTF DISCHARGE PORTS (1)

HIGH PISTON PUMPS CAT (Contact us if your pump is not listed here) 323 5 GPM 100 TO 1500PSI INLET 1000 BORE 0.866 STROKE 0.669 21 OZ. INJECTION PORT (1) 1/4 NPTF DISCHARGE PORTS (3) 430 5 GPM 100 TO 1000 PSI INLET 1040 STROKE 0.768 21 OZ. DISCHARGE PORTS (3) 3/4 NPTF 623 6 GPM 100 TO 1200 PSI INLET 850 STROKE 1.122 40 OZ. DISCHARGE PORTS (3) 820 10 GPM 100 TO 1000PSI INLET 940 BORE 0.984 STROKE 1.102 40 OZ. DISCHARGE PORTS (3) 1010 13 GPM 100 TO 700 PSI INLET 900 BORE 1.122 STROKE 1.102 40 OZ. DISCHARGE PORTS (3) 3/4 NPTF 1520 15.1 GPM 100 TO 1000 PSI INLET 830 BORE 1.122 STROKE 1.417 84 OZ. 1 1/4 NPTF DISCHARGE PORTS (3) 2520 25 GPM 100 TO 800PSI INLET 772 BORE 1.490 STROKE 1.417 84 OZ. 1 1/4 NPTF DISCHARGE PORTS (3) 2520C HI-TEMP COOLED INLET 25 GPM 100 TO 800PSI INLET 772 BORE 1.490 STROKE 1.417 84 OZ. 210 F 1 1/4 NPTF DISCHARGE PORTS (3) CIRCULATING PORTS (2) 1/4 NPTF COOLING FLUID CAPACITY 1.6 QTS. 6020 60 GPM 100 TO 1000 PSI INLET 500 BORE 2.205 STROKE 2.461 320 OZ. 2 NPTF DISCHARGE PORTS (3) 1 1/4 NPTF SHAFT DIAMETER (D-END) 1.772 WEIGHT 235 LBS.

INLET 6024 12 GPM 100 TO 5000PSI 500 BORE 0.984 STROKE 2.480 320 OZ. 140 F 2 NPTF DISCHARGE PORTS (3) SHAFT DIAMETER (D-END) 1.772 WEIGHT 265 LBS. DIMENSIONS 31.4 X 24.0 X 17.1 HIGH PISTON PUMPS PRATASSOLI DIMENSIONS 35.3 X 24.0 X 17.1 *PUMP SHOWN WITH OPTIONAL OILERS INLET 6040 40 GPM 100 TO 1500 PSI 500 BORE 1.811 STROKE 2.461 320 OZ. 2 NPTF DISCHARGE PORTS (3) 1 1/4 NPTF SHAFT DIAMETER (D-END) 1.772 WEIGHT 235 LBS. *PUMP SHOWN WITH OPTIONAL OILERS INLET 6044 20 GPM 100 TO 3000 PSI 500 BORE 1.260 STROKE 2.480 320 OZ. 140 F 2 NPTF DISCHARGE PORTS (3) SHAFT DIAMETER (D-END) 1.772 WEIGHT 265 LBS. DIMENSIONS 35.3 X 24.0 X 17.1 *PUMP SHOWN WITH OPTIONAL OILERS EK SERIES MAX. INLET : 45 PSI MAX. FLUID TEMPERATURE: 140 F INLET PORT THREAD: 1 IN. BSP-F DISCHARGE PORT THREAD: 3/4 IN. BSP-F SHAFT DIAMETER: 1.181 IN./30 MM PUMP DIMENSIONS: 18.2 IN. X 17.5 IN. X 7.3 IN. : 100 OZ. STROKE: 1.575 IN./40 MM SHIPPING WEIGHT: 120 LBS. MODEL NO. -GPM -PSI BORE MIN. INLET-PSI EK18 7.9 4350 1000.709 IN./18 MM 4.8 EK20 9.8 3600 1000.787 IN./20 MM 4.8 EK22 11.9 3050 1000.866 IN./22 MM 4.9 EK25 15.6 2300 1000.984 IN./25 MM 4.9 EK30 16.3 2150 750 1.181 IN./30 MM 4.9 HD SERIES MAX. INLET : 45 PSI MAX. FLUID TEMPERATURE: 140 F INLET PORT THREAD: 1 IN. BSP-F DISCHARGE PORT THREAD: 3/4 IN. BSP-F SHAFT DIAMETER: 1.378 IN./35 MM PUMP DIMENSIONS: 20.4 IN. X 17.7 IN. X 8.1 IN. : 127 OZ. STROKE: 1.575 IN./40 MM SHIPPING WEIGHT: 145 LBS. MODEL NO. -GPM -PSI BORE MIN. INLET-PSI HD18 7.9 7250 1000.709 IN./18 MM 4.8 HD20 10.0 5800 1000.787 IN./20 MM 4.8 HD22 12.0 4650 1000.866 IN./22 MM 4.9 HD25 15.6 3600 1000.984 IN./25 MM 5.1 KL SERIES MAX. INLET : 45 PSI MAX. FLUID TEMPERATURE: 140 F INLET PORT THREAD: 1 1/2 IN. NPT-F DISCHARGE PORT THREAD: 1 IN. NPT-F SHAFT DIAMETER: 1.378 IN./35 MM PUMP DIMENSIONS: 19 IN. X 17.7 IN. X 8.4 IN. : 127 OZ. STROKE: 1.575 IN./40 MM SHIPPING WEIGHT: 155 LBS. MODEL NO. -GPM -PSI BORE MIN. INLET-PSI KL30 22.2 2600 1000 1.181 IN./30 MM 5.4 KL33 27.0 2150 1000 1.300 IN./33 MM 5.7 KL36 32.2 1750 1000 1.417 IN./36 MM 6.0 KL40 33.8 1600 850 1.585 IN./40 MM 5.7 KL45 40.1 1450 800 1.772 IN./45 MM 6.0 MS SERIES KL50 MAX. INLET 43.3 : 45 PSI 1150 MAX. FLUID TEMPERATURE: 700 1.969 140 F IN./50 MM 5.8 INLET PORT THREAD: 2 1/2 IN. NPT-F DISCHARGE PORT THREAD: 1 1/4 IN. NPT-F SHAFT DIAMETER: 2.758 IN./70 MM PUMP DIMENSIONS: 27.7 IN. X 23.8 IN. X 11.9 IN. CRANKCASE MODEL NO. CAPACITY: -GPM 333 OZ. STROKE: -PSI 2.362 IN./60 MM SHIPPING WEIGHT: BORE 570 LBS. MIN. INLET-PSI MS36 35.9 4350 750 1.417 IN./36 MM 6.5 MS40 44.4 3500 750 1.575 IN./40 MM 6.8 MS45 56.3 2750 750 1.772 IN./45 MM 7.1 MS50 69.5 2250 750 1.969 IN./50 MM 7.6 MS55 84.0 1800 750 2.165 IN./55 MM 7.8

HIGH PISTON PUMPS PRATASSOLI (Contact us if your pump is not listed here) MSN SERIES MAX. INLET : 45 PSI MAX. FLUID TEMPERATURE: 140 F INLET PORT THREAD: 2 1/2 IN. BSP-F DISCHARGE PORT THREAD: 1 1/4 IN. BSP-F SHAFT DIAMETER: 1.969 IN./50 MM PUMP DIMENSIONS: 27.7 IN. X 23.8 IN. X 11.7 IN. : 333 OZ. STROKE: 2.362 IN./60 MM SHIPPING WEIGHT: 650 LBS. MODEL NO. -GPM -PSI BORE MIN. INLET-PSI MSN3615R1-5 35.4 4350 1500 1.417 IN./36 MM 6.5 MSN3618R1-5 35.9 4350 1800 1.417 IN./36 MM 6.5 MSN4015R1-5 43.9 3500 1500 1.575 IN./40 MM 6.8 MSN4018R1-5 44.4 3500 1800 1.575 IN./40 MM 6.8 MSN4515R1-5 55.5 2750 1500 1.772 IN./45 MM 7.1 MSN4518R1-5 56.3 2750 1800 1.772 IN./45 MM 7.1 MSN5015R1-5 68.7 2250 1500 1.969 IN./50 MM 7.6 MSN5018R1-5 69.5 2250 1800 1.969 IN./50 MM 7.6 VH SERIES MAX. INLET : 45 PSI MAX. FLUID TEMPERATURE: 140 F INLET PORT THREAD: 90 MM BSP-F DISCHARGE PORT THREAD: 1 1/4 IN. BSP-F SHAFT DIAMETER: 1.969 IN./50 MM PUMP DIMENSIONS: 33.3 IN. X 28.2 IN. X 13.5 IN. : 467 OZ. STROKE: 2.835 IN./72 MM SHIPPING WEIGHT: 880 LBS. MODEL NO. -GPM -PSI BORE MIN. INLET-PSI MH4515R1-5 51.2 4350 1500 1.722 IN./45 MM 5.2 MH4518R1-5 49.4 4350 1800 1.722 IN./45 MM 5.2 MH5015R1-5 63.4 3500 1500 1.969 IN./50 MM 5.4 MH5018R1-5 61.0 3500 1800 1.969 IN./50 MM 5.4 MH5515R1-5 76.6 2900 1500 2.165 IN./55 MM 5.5 MH5518R1-5 74.0 2950 1800 2.165 IN./55 MM 5.5 MH6015R1-5 91.1 2400 1500 2.362 IN./60 MM 5.8 MH6018R1-5 88.0 2550 1800 2.362 IN./60 MM 5.8 VH MH6515R1-5 SERIES MAX. INLET : 107.0 145 PSI MAX. 2050 FLUID TEMPERATURE: 1500 86 F 2.559 IN./65 MM 6.1 INLET PORT THREAD: 3/4 IN. BSP-F DISCHARGE PORT THREAD: 1/2 IN. BSP-F MH6518R1-5 103.0 2100 1800 2.559 IN./65 MM 6.1 SHAFT DIAMETER: 1.378 IN./35 MM PUMP DIMENSIONS: 22.7 IN. X 17.7 IN. X 8.3 IN. : 127 OZ. STROKE: 1.575 IN./40 MM SHIPPING WEIGHT: 185 LBS. MODEL NO. -GPM -PSI BORE MIN. INLET-PSI VH12 2.6 17500 750.472 IN./12 MM 90 VH14 3.6 14500 750.551 IN./14 MM 90 VH16 4.7 10800 750.630 IN./16 MM 90 SH SERIES MAX. INLET : 100 PSI MAX. FLUID TEMPERATURE: 86 F INLET PORT THREAD: 1 1/2 IN. BSP-F DISCHARGE PORT THREAD: 3/4 IN. BSP-F SHAFT DIAMETER: 1.969 IN./50 MM PUMP DIMENSIONS: 42.4 IN. X 25.8 IN. X 13.7 IN. : 467 OZ. STROKE: 3.543 IN./90 MM SHIPPING WEIGHT: 840 LBS. MODEL NO. -GPM -PSI BORE MIN. INLET-PSI SH2001 11.3 20300 1500.787 IN./20 MM 90 SH2017 11.6 17400 1750.787 IN./20 MM 90 SH2201 13.7 15950 1500.866 IN./22 MM 90 SH2217 14.0 15950 1750.866 IN./22 MM 90 SH2401 16.3 13800 1500.945 IN./24 MM 90 SH2417 16.6 13800 1750.945 IN./24 MM 90 SH2601 19.2 11600 1500 1.024 IN./26 MM 90 SH2617 19.5 11600 1750 1.024 IN./26 MM 90 SH2801 22.3 10150 1500 1.102 IN./28 MM 90 SH2817 22.7 10150 1750 1.102 IN./28 MM 90 LH SERIES MAX. INLET : 45 PSI MAX. FLUID TEMPERATURE: 140 F INLET PORT THREAD: 90 MM BSP-F DISCHARGE PORT THREAD: 1 1/4 IN. BSP-F SHAFT DIAMETER: 1.969 IN./50 MM PUMP DIMENSIONS: 36.3 IN. X 25.8 IN. X 13.5 IN. : 467 OZ. STROKE: 3.546 IN./90 MM SHIPPING WEIGHT: 800 LBS. MODEL NO. -GPM -PSI BORE MIN. INLET-PSI LH4015 45.4 4350 1500 1.575 IN./40 MM 5.1 LH4017 49.7 4350 1750 1.575 IN./40 MM 5.1 LH4515 57.6 3500 1500 1.772 IN./45 MM 5.4 LH4517 62.9 3500 1750 1.772 IN./45 MM 5.4 LH5015 71.1 2900 1500 1.969 IN./50 MM 5.5 LH5017 77.4 2900 1750 1.969 IN./50 MM 5.5 LH5515 86.1 2300 1500 2.165 IN./55 MM 5.8 LH5517 93.8 2300 1750 2.165 IN./55 MM 5.8 LH6015 102.0 2050 1500 2.362 IN./60 MM 6.1 LH6017 112.0 2050 1750 2.362 IN./60 MM 6.1

TECHNICAL DATA Note: the components listed herein may differ from the pictures shown

Pressure pumping & washing equipment ELECTRIC DRIVEN, COLD WATER WASHING & PUMPING SYSTEMS Available Specifications: 1000 psig to 7250 psig / 2 gpm to 200 gpm ELECTRICALLY HEATED, HOT WATER WASHING SYSTEMS Available Specifications: 1000 psig to 5000 psig / 2 gpm to 16 gpm EXPLOSION-PROOF, HOT & COLD WATER WASHING SYSTEMS Class I,II, Division 1, Groups C, D, F & G Available Specifications: Cold Water-1000 psig to 7250 psig / 2.2 gpm to 65 gpm Hot Water-1000 psig to 5000 psig / 2 gpm to 16 gpm VFOS (VARIABLE FREQUENCY OPERATING SYSTEM), MULTI-STAGE, AND TANK-FED WASHING & PUMPING SYSTEMS Available Specifications: 1000 psig to 5000 psig / 8 gpm to 100+ gpm NATURAL GAS & PROPANE FIRED HOT WATER WASHING SYSTEMS Available Specifications: G30/P30 Series-1000 psig to 3000 psig / 4 gpm to 6 gpm 300,000 BTUH INPUT (2)G40/(2)P40 Series-1000 psig to 3000 psig / 4 gpm to 16 gpm 395,000 & 790,000 BTUH INPUT ENGINEERED PUMPING & WASHING SYSTEMS Available Specifications: Designed/built to application requirements ASME B31.1, 2004 & N285.0 Class 6 code compliant designs Certified safety, limit and performance testing and validation MTC (material traceability certificate) Level II 3300 Steeles Ave. West, Concord, Ontario, Canada L4K 2Y4 tel: 800-246-9689 / 905-761-1733 fax: 905-738-6168 www.pscclean.com email: info@pscclean.com COPYRIGHT 2012 PSC CLEANING SYSTEMS INC., ALL RIGHTS RESERVED